Search Documents

By J. H. Johnson, H. J. Schock

The cases of no auxiliary ventilation and ventilation with tubing were mathematically modeled, using a turbulent dispersion model. The Scooptram® used to load is modeled as a variable-speed, variable-strength source of pollutants moving in and out of the dead-ended drift. Model predictions are compared to experimental measurements. A parametric analysis was performed to determine If a relationship existed between C02 and NO levels. It was concluded from this analysis that when modeling a load-haul-dump cycle, it is necessary to use a model that can predict changes in source strength as well as source location. Carbon dioxide was used as a tracer to calibrate the model since, knowing the fuel flow rate, it is possible to calculate C02 production. The model was then verified after this calibration process using additional experimental results. With the calibrated model, it is possible to predict pollutant concentrations at any location in the heading using an engine map and the previously calculated flow field.

Jan 1, 1984

By A. A. Collins

OF widespread interest to all lead metal¬lurgists is a dross smelting process that will consistently give mattes and speiss of low lead and high copper contents. It is -a problem that has intrigued operators through the years. In the past few years, with increased amounts of copper and overcrowded metallurgical furnaces, it has been almost imperative to evolve some method. Experience at El Paso has shown that high copper-to-lead ratios can be consistently attained by use of the new soda process.* OLDER METHODS Three older methods; i.e., I. Dross plus siliceous ore and limestone, 2. Dross plus one fourth blast-furnace speiss and siliceous ore, 3. Dross plus sulphides and siliceous ore and scrap iron, do not give consistent results and the products are higher in lead and lower in copper than those produced with the soda process. Any radical changes in the blast-furnace drosses will throw any of these older methods into a tailspin. For almost ten years, El Paso used the third method, with varying results. It was noted that as the arsenic and antimony contents of the dross increased, the speiss and matte steadily increased in lead and decreased in copper. A dross containing four parts of copper to one part of arsenic was considered to be ideal. At times this balance of copper to arsenic was almost impossible to obtain, especially when handling copper Cottrell dusts, which vary so greatly in copper and arsenic. Custom smelters like El Paso, handling a great variety of dusts, concentrates and ores, are apt to have anywhere from 1 to 15 pct copper on charge, with a variable in arsenic of from 0.5 to 2 pct. With such conditions, and drosses varying from 12 to 40 pct copper, an operator using the older dross reverberatory practices would find it just about im¬possible to control the reverberatory operations and to produce a good product low in lead and high in copper. These conditions prevailed at El Paso from the year 1940 to the present. In May 1942 it, was decided to experiment with the soda process. THE SODA PROCESS After considerable work the soda method was finally evolved to the present state. It has never failed to produce a good product even under the most adverse conditions. It might be well to remember that many men of thought in the smelting industry have at one time or other suggested the removal of all copper, arsenic and antimony from the lead blast-furnace charge as an aid to better metallurgy.

Jan 1, 1947

By L. W. Fagg

The purpose of this paper is to present in a convenient form data and examples necessary in making dynamometer card analyses; also to outline a procedure of well weighing. Many articles and papers have been written delving into the mathematical considerations relative to the shape and characteristics of dynamometer cards. However. it is recognized that there are too many unknown factors involved in such calculations to assure a workable degree of accuracy. For this reason the accepted procedure is to take dynamometer cards on wells in question rather than try to calculate the load curve. The polished rod dynamometer is now recognized as a necessary tool for measuring loads, torque, and horsepower. It is also used to determine pump action and trouble-shoot for any seemingly abnormal pumping condition. The apparently infinite variety of a = maximum load (height x scale constant) b = minimum load. Range of load is difference between maximum and minimum load speed—taken with stop watch stroke —measured at polished rod c = beginning of down stroke in direction of arrow. (End of up stroke) d = beginning of up stroke. (End of down stroke). Polished Rod Horsepower = (Area of card) x Scale const. x Stroke x Length x spm (Length of card) 33000x 12 1.35 1.35------x5300x 24 x 12 2.53 --------------------------= 2.06 23000x12 Appraximate Peak Torque: Upstroke = (2390) (12) (1) = 28,700 in. Ib Downstroke = (1 860) (12) (.866) = 19,300 in. Ib Counterbalance should be increased to make up stroke and down stroke peak torque equal. FIG. 1 dynamometer cards that can be obtained is one reason for the general lack of usage of the dynamometer as a control instrument rather than a means for making routine measurements of leads and horsepower. When it is considered that the dynamometer card is a record of the resultant of all forces acting on the polished rod at any particular instant during the pumping stroke. the problem is then one of breaking down this resultant into its various components. As a means of a quick review we shall consider the examples shown in Figs. 1 to 9: and Tables I and II and then proceed to the interpretation of variously shaped cards caused by some abnormal operating condition. In Table 11, when we were considering the factors involved in calculating the peak polished rod load, it can be seen that the factors involved greatly oversimplify the problem. Certain assumptions are made which may or may not he even close to the actual field conditions, such as the specific gravity of the fluid generally considered as one; that the crank has constant angular velocity; that the down-hole friction is zero; and that the fluid lift is from the pump. In the following examples we shall see what a variation in fluid weight and friction can do to the general shape and magnitude of the dynamometer card. (Figs. 10 to 22.) MAKING THE WELL STUDY It is obvious that it would be impractical to consider in detail all of these factors each time a well study is made, inasmuch as each well study job could conceivably be extended into a research project rather than serve the practical requirements of finding the answer to a specific problem. For this reason it is important that some objective be established previous to the time the well study is made. Load at TU = 3070 Ib Crank angle when polished rod is at position TU = ? ? = 30° Maximum counterbalance effect at polished rod = 2760 Ib Torque at TU = (Load at TU — Max. counterbalance effect-lbs) sin 0 x Length of Stroke 2 = (3070-2760) .5 x 24 = 1860 in. 15 2 Torque at TD = (Load at TD — Max. counterbalance effect-lbs) sin ? x Length of Stroke 2 = (530 - 2760) sin 330' x 24 = 13,400 in. Ib 2 Note: sin 0 from c to d on UPSTROKE will be positive value. sin 0 from c to d on DOWNSTROKE will be negative value Torque at c and d is zero because 0 is zero. FIG. 2 —APPROXIMATE METHOD FOR CALCUlATlNG TORQUE

Jan 1, 1950

By Fred P. Peters

At first glance this paper may seem unique among those comprising this symposium on designing for powder metallurgy, since it is evidently concerned with everything but Powder metallurgy. This paradox mill be at once resolved, however, when the real Purpose of the symposium meeting is understood—to present factually and objectively the things that can and cannot he done with powder-metallurgy methods, and especially to set forth with brutal frankness the limitations of Powder metallurgy, so that costly over-enthusiasm and misapplication may be prevented. Since much of powder metallurgy's future development (and many of its present disappointments) has been in competition with other and long-established methods of fabricating parts, it is easy to see that its true competitive possibilities in any given case cannot be accurately appraised without rudimentary knowledge of what the competition can do. This paper, therefore, presents a few reminders of things you all know—a background to be kept in mind as you examine the data on each of their specialties given by the authors of the papers that follow. From the standpoint of the design engineer powder metallurgy is often in Competition with one or more of the following: sand casting, die casting, permanent-mold casting, precision investment casting, ma- chined bar stock, screw-machine parts, cold-heading, drop-forging, and stamping and drawing. We will here briefly discuss each of these individually, and set forth so, rough (and therefore dangerous) generalizations about its competitive position, especially with respect to powder metallurgy. Sand Casting Sand-casting of small parts is sometimes an inexpensive method of manufacture, for its raw-material costs (i,e., for gray iron) are the lowest of the various methods and it involves the use of no tools and dies of jewelry quality. its design flexibility— that is, the ability to make complicated, cored and undercut parts in one piece—is about the highest of the competing processes and in this respect it can do many things that are impossible by powder metallurgy. For small castings its production rates may be higher, by using multi-impression molds, than can be achieved with parts of the same size by powder metallurgy. But its labor charges for melting, pouring, patternmaking and molding are comparatively high and the waste it entails in gates and risers is always considerable. Tolerances of sand castings are wide (+1/6 to 1/32 in- per in.) and where precision approaching that of powder metallurgy is required sand castings must be machined to final size, thus increasing their cost. Steel sand castings are more expensive and less precise than iron, and nonferrous the most costly of all.

Jan 1, 1945

By M. N. Shetty

LARGE copper whiskers were grown from cuprous iodide by reduction with hydrogen at about 500°C. Carefully selected single-crystal whiskers of [loo], [110], and [Ill] orientations were used and the whisker shapes and cross sections are shown in Fig. 1. Spec-trographic analysis of a typical batch of whiskers showed that the composition was better than 99.9 pct with iron and silicon as the major impurities. The test specimens varied from about 70 to 400 u in diam and they did not show a conspicuous yield drop as observed in very fine whiskers (diam <25 u), tested by Brenner.1 The characteristics of the stress-strain curves were similar to those of bulk single crystals, even though the maximum flow stresses reached in some orientations were comparable to the yield stresses observed in fine whiskers. Mechanical properties of whiskers of different materials and copper whiskers up to about 100 u in diam have been reviewed,&apos; and a mechanism of slip band propagation in fine whiskers has been recently suggested.3 Whiskers in this work were tested in a floor-model Instron testing machine using low strain rates. (Details of the testing procedure, diameter dependence of the yield stress, and the characteristics of the load elongation and stress-strain curves have appeared esewhere.4) Due to the extensive deformation, >50

Jan 1, 1970

By V. M. Frey

IN 1936 the foreman at one of the oldest limestone quarries in northern Virginia discovered the remains of three old well-drill holes that contained dynamite. As consulting engineer for the property, I was then called upon to devise a method for removing the explosive. As no exact formula for the handling of unexploded dynamite exists, the proper steps for removing it must always be dictated by local conditions. A description of the procedure in this case may, therefore, be of interest to others faced with a similar problem.

Jan 1, 1939

By J. W. Leonard, J. C. Anderson, C. T. Holland

PREPARATION CONTROL IN UNDERGROUND MINING Selective Mining According to district Depending upon the particular geographic location or seam characteristics modem raw coal preparation practices can be used to obtain improved product quality and uniformity. Nevertheless, certain coal markets may require only marginal quality while others may require very high quality and these objectives may be sought by commencing the preparation of coal underground at the "working face." Underground preparation involves choosing those portions of the bed which can be cleaned to satisfy predetermined market requirements involving (1 ) maintenance of uniformity in chemical quality, (2) elimination of removable impurities, (3) control of sizes and size ratios and (4) control of moisture. The methods employed to attain these objectives vary widely with the (1) seam under development, (2) mining equipment available and (3) changing trends in the consuming markets. When a mining property is opened and development progresses from one section to another the (1) petrography of the coal in the bed does not re- main uniform, (2) character of roof and floor are subject to change and (3) character and prevalence of mineral impurities are subject to considerable variation. The quality of coal shipped to market from any mine depends upon intelligent foresight, planning, execution and supervision. Mining becomes a highly technical art. The quality of coal as determined by chemical and petrographic analysis is without question one of the most important considerations in the development and life of any coal-mining property. Variations in such proper- ties as volatile matter, ash, sulfur, Btu content and petrography are of considerable interest and to a limited extent so are such properties as phosphorous content, free swelling index, plasticity, hardness, pressure formation during coking and ash composition. The maximum and minimum specifications of these characteristics as established by competitive market conditions place definite limits on the marketability of a coal. The prospecting and evaluation of any area containing one or more salable coal beds by means of channel samples taken from outcrop openings and/or from diamond-drill cores can yield valuable data on coal characteristics. By correlating the data developed from distinct petrographic sections of channel and/or drill core samples, the quality of the bed according to stratification will be evident. There are few coal beds that do not show wide variations of such characteristics as ash and sulfur

Jan 1, 1968

By W. B. Tucker

UNUSUAL interest has recently centered in the Mojave mining district of California, owing to new discoveries of gold ore at the Silver Queen mine, and subsequently at other neighboring proper- ties. These finds have proved that opportunities exist for the prospector even in old mining districts, where careful search may still be rewarded. The Mojave district is characterized by a group of small hills centering around Soledad Butte, four to six miles southwest of Mojave, in Kern County. This butte is 1250 ft. higher than the surrounding desert and 4000 ft. above sea level. Four miles west of Soledad Mountain are the so-called Middle Buttes, a group of flat-topped hills. Gold was first discovered in the district in 1894, and the following productive mines developed: Queen

Jan 1, 1936

By W. F. Netzeband

Jan 1, 1927

By C. S. Smith, Chih-Chung Wang

TURNBULL and his collaborators1,2 have developed the theory of homogeneous nucleation as applied, inter alia, to solidification of liquid metals. Vonnegut³ and Turnbull4 have shown that if a liquid metal is subdivided into small droplets a vast majority of them will undercool very considerably before solidification, generally to as low as about 0.8 of the freezing temperature on the absolute scale. The nuclei effective at small degrees of supercooling in bulk metal seem to be internal or surface heterogeneities, relatively small in number. If the metal is subdivided, those droplets that happen to contain such nuclei will solidify at a temperature not greatly below the true freezing point, but only a small part of the whole volume will be affected and the majority of the drops will under-cool to the much lower temperature at which homo- geneous nucleation occurs as a result of fluctuations. It occurred to one of the authors that an appropriate subdivision to give effective freedom from random nuclei is produced during the solidification of many alloys that contain a minor amount of a phase of low melting point, and that one might then expect marked undercooling of the distributed phase. Experimental: The alloys selected for initial study were copper with minor amounts of lead and bismuth, and aluminum with tin. In all these alloys, the major component freezes at a temperature not much below that of the pure metal, and there is little further change in constitution on cooling until the lower melting point constituent freezes in an almost pure state. Cooling curves were taken using the controlled heat flow method permitting approximate specific heats to be obtained. Chromel-alumel thermocouples were used, with the standard emf tables, since extreme precision was not needed. The crucible (3/4 in. id, 5/16 in. wall) was made of B & W K-20 insulating brick. It held about 10 cc of the alloy being investigated. The cooling rate was 2.5" to 2.9°C per min under a controlled temperature difference of 20°. Approximate specific heats were computed from the inverse rate curves together with data from a blank run and from a standard run with a copper cylinder of known heat capacity. The alloys for investigation were made from high-purity metals (99.99+pct) and cast into graphite molds. The castings were machined to fit the crucible and to provide a hole for the inner thermocouple. Cooling curves were taken after heating to a temperature about 50" above the melting point of the minor, lower melting-point, constituent. Results The lead phase in an alloy of copper with 5 pct lead did not undercool more than 3" below the melting point of lead (327°C) either as cast or after annealing to produce a new dispersion of the liquid phase. A copper-zinc-lead alloy with 23.75 pct zinc and 5 pct lead undercooled more but showed no thermal effect below 319°C. A cast alloy of copper with 5 pct bismuth undercooled to 249°C (M.P. bismuth 27l °C), but once solidification started it was completed at the same temperature. This was anticipated, since the bismuth forms a nearly continuous phase between the grains of copper, and a solid crystal nucleated anywhere would rapidly* con- sume the entire network of liquid, unless the physical continuity of the liquid were broken through volume changes, inadequate fluidity, or gas evolution. Similar arguments apply in the case of copper-lead alloys, where the lead-rich liquid forms a network along grain edges, though not grain faces. In both cases there would be a few isolated particles

Jan 1, 1951

By J. A. Benell

DIOXIDE of silicon, commonly called silica, is one of the greatest single constituents of modern in-dustry. It is brought most clearly to the mind when we consider the various kinds of sand and their rela-tion to industry. The major portion of.all sand is silica, and should be its principal component part in building materials. As an abrasive for cutting, polish-ing and sand-blasting, sand serves a vital purpose in many industries. Even lumber is now being sand-blasted, to cut away the softer grains of wood, leaving the harder grains in relief. The result not only in-creases the beauty of the wood, but adds to it an ap-pearance of antiquity. The common uses of silica in industry may be classified about as follows: Chemical industries-filtering medium; manufacture of carborundum; manufacture of water-glass. Paint-inert extender. Mineral fillers-wood filler; filler in rubber, hard rubber, pressed and molded goods, phonograph records.

Jan 5, 1928

By Joseph J. Yancik, Leonard L. Felts, George B. Clark

Little information has been published concerning the actual or useful amount of energy obtained from explosives when they are used for blasting. To provide more data on this subject, 8-in. neet cement cubes were blasted in a steel plate box and the breakage energy evaluated by comparison with drop crusher results using Rittinger&apos;s," &apos; Kick&apos;s,%nd Bond&apos;s&apos; theories. Theories by Bond and Wang," Lineau,&apos; Hatch,&apos; Roller," and others were not considered applicable. Those used in this investigation may be expressed mathematically as follows: [ ] The above equations were employed to determine values of KK, K for particle size distributions similar to those obtained from the blasting curves. These values were in turn used as a means of approximating the specific energy of the blasted material. The efficiency of crushing by blasting was then determined by dividing this specific energy by the maximum available work of the explosive per gram of cement.

Mar 1, 1956

By Charles Austin

IN a recent paper the authors1 discussed the reactions to tempering of hypereutectoid steels quenched from 1000° C., as revealed by studies on changes in hardness, electrical resistivity, coercive force and metallo-graphic characteristics. The data, which related specifically to temper-ing temperatures of 550°, 650° and 710° C., for varying periods up to 125 hr., permitted the following important conclusions: 1. The rate of softening of the steels at the temperatures examined differed markedly although the steels were of "similar" general chemi-cal composition. 2. The temperature of maximum softening spread over a range from about 650° C. to the eutectoid inversion. 3. The divergence in behavior was ascribed, at least in part, to a profound difference in tendency to graphitization on annealing at sub-eutectoid temperatures. 4. The mode of spheroidization of the cementite, as revealed by metallographic studies, also varied considerably in the different steels. The purpose of the present investigation is to pursue further the study of the difference in behavior of the steels on tempering over a wider range of temperature. To this end the following features have received particular attention: 1. Comparison of temperatures of maximum softening of the various steels when the quenched samples were tempered for 5 hr. and for 75 hr. followed by furnace cooling and by quenching in water. 2. Determination of the effect of quenching temperature, prior to tempering, on the rate of softening. Quenching temperatures of 1000° and 850° C. were used in the investigations. 3. Examination of the microstructures obtained with the various heat-treatments employed.

Jan 1, 1938

Alpha Portland Cement Co.&apos;s mining operations at Manheim W. Va., produce 750,000 bbl of limestone yearly, averaging 2200 bbl per working day. Thirteen parallel entries have been driven to date, each almost 30 ft high and about 45 ft wide, extending back 5000 ft to the working faces. Pitch of the seam from the lowest to the highest entries is steep enough to provide excellent year- round natural ventilation, and this, together with the size of the entries and a good bottom, has allowed face crews to drive right up to the working areas in the family car.

Oct 1, 1956

"Located at Canyon Ferry on the Missouri River, 17 miles from Helena and 63 miles from Butte. River drainage area 15,570 sq. miles. Built in 1898.DAM: Rock-filled, wooden crib, 490' long and 39' feet at maximum head; also masonry core, earth bulk-head 300' long and granite masonry abutments.SPILLWAY: 473' long, crest elevation 3660.5; steel flashboard system 10' high.PENSTOCKS: 10 main penstocks, 12' diam., about 40' long, leading from canal to turbines, each supplying 1 pair turbines.WHEELS: 4 main center discharge, horizontal units, each 1 pr. of 42"" wheels made by Dayton Globe Iron Works, and 6 main units, each 1 pr. of 45"" wheels made by S. Morgan Smith Co., all 157 r. p. m., normal head 34', and direct coupled to generators.GENERATORS: 10 W. E. & M. Co., Kodak Type, revolving armature, 750 k-w., 157 r. p. m., 550 v., 3 phase, 60 cycle alternators.OPERATION: The plant has large water storage and can carry peak loads to 12,000 h-p. It is the central control station for the system."

Jan 1, 1913

A. Bement, Chicago,Ill. (communication to the Secretary*):— Formerly it was the general practice of engineers to designate coal that is free from moisture and ash as " combustible," notwithstandirig that it contains oxygen and nitrogen. The origin of this practice was more particularly due to the requirements in connection with boiler-testing, which demanded a consideration of that portion of the fuel which took part in the combuition-process because results based on a unit of either moist or dry coal were not comparable, since both moisture and ash were recognized as variable quantities. Thus, a pound of " combustible " became a standard of value, and was treated as a constant before employing measurements of heating-power and calculating therefrom the percentage of efficiency. The recognition of this term " combustible " was an advance to be credited to the engineer rather than to the chemist, because the latter, not having to do with the interpretation of analyses in practice outside the laboratory, usually saw no reason for reporting results in terms other than those of the moist-coal composition. Some years ago I needed a table of fuel-composition in terms of moist, dry, moisture-free and ash-free coal, and of the combustible components. This table required the use of the word combustible in its proper sense, for the purpose of designating carbon, hydrogen, and sulphur, instead of including these three elements with oxygen and nitrogen, to which aggregate the term combustible was formerly applied. To make such a tabulation involved either the use of the inconvenient and cumbersome term, "ash- and moisture-free coal," or of some other representative term, and for this purpose I adopted the expression pure coal, which is short, simple, convenient, and technically correct. It is also harmonious, because it agrees

Jan 1, 1909

By J. Kucera, J. Vreštál

DIFFERENT authors1 &apos; have been engaged in meas-uring the vapor pressure of pure cobalt. The results of their measurements satisfy the expected temperature dependence of vapor pressure and are in mutual agreement, with the exception of the results by De Dyk Man and ~esmejanov.~ The latter authors, by using the effusion method, have achieved considerably higher values than other workers. By using the isotope exchange method they obtained much lower values than other authors. The determination of thermodynamic functions of the binary Ni-Co system was carried out, as far as we know, only by De Dyk Man and Nesmejanov.4 This determination was based on extremely low values of vapor pressure over pure cobalt obtained by the isotope exchange method. Therefore we considered it useful to repeat these measurements. Furthermore, the reliable values of thermodynamic functions should complement the migration characteristics, the inner magnetic field data obtained by Miissbauer effect measurements, specific heat data, and the K effect and positron annihilation characteristics that have been achieved for the Ni-Co system in the Institute of Metallurgy of the Czechoslovak Academy of Sciences in Brno.5-9 The measurements in this paper were performed by the isotope exchange method. In this method, as has been shown by analysis,10-&apos;3 the vaporization rate, w, can be calculated from the relation w = k/1oSw [1] i0Sw) [1] where L, is the activity per unit mass of the source, S is the area of evaporation, k is the tangent at the point t = 0 to the curve giving the radioactivity de-pendence of the target vs annealing time, t, and wis the probability for the tracer atom condensation on the target surface. The value for cc. can be obtained from the equation w = a + 2P(l-a) [2] where P is Clausing&apos;s coefficient and a is the condensation coefficient. In the present work the cylinder shaped containers for annealing the samples were used, characterized by the ratio 1:d = 1.06. Here 1 is the length and d the diameter of the container. For this ratio P = 0.514 and w =0.5, and w is independent of the condensation coefficient. The vaporization rate is related to the vapor pressure p by the relation where R is the gas constant, T is the absolute temperature, and M is the molecular weight of the component investigated. Measurements of the vapor pressure of the i component over the pure metal, p!, and the alloy, pi, at the given temperature and composition enable one to calculate the thermodynamic activity of this component from the equation ai=pi/pi [4] is and the activity coefficient ri=ai/xi [5] xi where xi is the molar fraction of the investigated alloy component. EXPERIMENTAL Evaporization rate measurements were carried out with pure cobalt and eight different Ni-Co alloys, which were kindly delivered by the Centre National de Recherches Me&apos;tallurgiques Liege, Belgium. The composition of the alloys is given in Table I. The cobalt used in these alloys contained the following impurities: 0.016 wt pct Fe, 0.014 wt pct Cu, 0.01 wt pct Mn. Other elements were present in much lower concentrations. From the melts, samples in the form of small cylinders of 12 mm in diam were ma-chined. The thickness of the targets and sources was 2.5 and 1.2 mm, respectively. The lower thickness of the sources was chosen to make their over-all ac-tivity as low as possible. Sources were activated in

Jan 1, 1970

By L. Bombardieri, H. F. Mills

IRON KING mine, producing gold-silver-lead-zinc ore, is 10 miles east of Prescott, Ariz. At present the 1806 level is being developed. The echelon pattern of ore deposit continues at depth but is less pronounced, and the orebody is now more or less continuous over 2600 ft of strike length. with widths 5 ft to as high as 26 ft where overlapping of lenses occurs in one section of the mine. Better continuity of ore at depth has encouraged systematic mining and improved plant facilities to offset higher operating costs. With favorable persistence of ore at depth. the three-compartment No. 6 hoisting shaft appeared inadequate to handle increased tonnage from greater depths, and in 1952, a four-compartment steel and concrete shaft was started. This is now at a depth of 1906 ft, and shaft pockets and loading cartridges are being installed on the 1806 level. Ore from the new shaft, hoisted in 51/2 -ton Jeto bottom dump skips, is dumped into a 500-ton shaft bin, from which it is fed to a 16x30-in. gyratory crusher and conveyed 415 ft through an undersurface concrete gallery to the secondary crusher and conveying system supplying the 900-ton mill. Lead, zinc, and pyrite concentrates are floated, and the flotation tailings are cyanided after desliming. Waste from the new shaft is dumped into a 250-ton surge bin, fed from this bin to a 24-in. conveyor, and discharged into the glory hole above the block cave. The new shaft is served by a double-drum 400-hp hoist used for ore and waste; the No. 6 shaft conveys men and material To secure a cheap source of waste fill for stoping operations, a block cave area was undercut In the hanging wall near the north end of the mine above the 600 level. Waste from the block cave is drawn from any of three large drawpoints on the 600 level, and a series of hanging wall transfer raises with controls and bypasses on each level provide a fast low-cost material for fill. The block cave is worked vertically through to surface in the form of a steep-sided hole 350x250 ft and several hundred feet deep, the sides of which cave and provide fill material without any blasting. Fill is a mixture of caliche-cemented surface gravel and small particles of hanging wall schist. Level Development: An orebody 300 times as long as it is wide requires a lot of development work. Former practice consisted of driving a haulage drift about 30 ft from the ore in an andesitic footwall, a drift on the ore, and crosscuts from the haulage drift at 100-ft intervals. Crosscuts are about 90 ft long. At present, only the odd numbered levels are so developed, and on the even numbered levels only the haulage drift and crosscuts are driven. Little or no timber is used for this development. This change resulted in 20 pct reduction of development costs and 50 pet reduction of square set stoping required for removal of floor pillars. Elimination of ore drifts on alternate levels leaves

Jan 1, 1957

By J. O. Brittain, N. R. Adsit

A number of zinc bicrystal specimens with the grain boundary loaded in simple shear were plustically deformed in creep in a vacuum at 200°C and under an argon atmosphere at 350°C. The results indicated that the amount of grain boundary sliding at a given time was controlled by the slip in the grains and was proportional to the resolved shear stress on the slip plane. Curves of grain boundary sliding vs time were found to be cyclic with no regular periodicity. ALTHOUGH grain boundary sliding (G.B.S.) has been investigated in a number of different types of tests on various materials there is substantial disagreement on the interpretation of the various observations. Gifkins1 has presented a comprehensive review of the subject of G.B.S. and fracture. He reports that the activation energy for high-temperature creep is equal to that for volume self-diffusion and that pure metals show less tendency towards intercrystalline fracture than alloys. Pure metals show appreciably greater grain boundary migration than alloys, and both grain boundary migration and grain boundary sliding follow the same general trend in time as plastic deformation during creep.&apos; While there have been a number of different mechanisms proposed to account for G.B.S., none of the models explains all the results. Since zinc has only one prominent slip system, it was hoped that experiments on G.B.S. in zinc bicrystals might enable us to separate the effect of grain boundary angle and the effect of matrix slip and thereby resolve at least one part of this complex phenomenon. EXPERIMENTAL PROCEDURE Bicrystals of pure zinc (99.99 pct) were grown by a Bridgeman technique in a furnace having a gradient of 20°C per in. The bicrystals were seeded to a desired orientation and grown in a split graphite mold which was 3/4 by 5/8 by 8 in. The mold was enclosed in a Pyrex tube and the tube was evacuated and then filled with a small amount of argon before it was placed in the furnace. The growth rates were 1/2 to I in. per hr for the bicrystals and 1/2 to 3 in. per hr for the single-crystal seeds. The longitudinal V notches served to hold the grain boundary in position during the growth process. A schematic rep- resentation of a specimen which had been cut with a jewelers saw from the bicrystals is shown in Fig. 1. All specimens of a series were cut from the same crystal, some of which were 7 in. in length. After specimen preparation the boundary was approximately 5/16 in. long and the V notches had a radius of 1/16 in. The boundaries were straight at a magnification of X100 with the exception of a few which had a gradual radius of curvature of greater than 3.2 in.-1. Laue back-reflection photograms were taken on the specimens to check the orientation of grains in the bicrystals. The method of relating the orientation of the two lattices is shown in Fig. 1, where 0 is the angle between normal to the boundary and the trace of the basal plane, is the angle in the boundary between the trace of the basal plane and a line parallel to the V notch, and x is the angle in the basal plane between the Burgers vector and the perpendicular to the grain boundary. After mechanical polishing the specimens were chemically polished.2 Subsequent to the polishing operation the specimens were encapsuled under a vacuum of better than 25 annealed at 340°C for 1 hr to remove the effects of this handling, and again chemically polished. Finally, fiduciary marks were scribed on the specimen using a micromanipulator. Creep tests, which were conducted in a modified Bausch apparatusS with the boundary loaded in simple shear, were run at a constant load (since the boundary area remained essentially constant this is approximately constant grain boundary stress). The temperature was controlled to ±1/4°C as measured on a semiprecision potentiometer with a calibrated thermocouple. The specimens were tested in a vacuum of better than 0.5 at 200°C and in purified argon at a pressure of 1/2 atm at 350°C. The op-

Jan 1, 1965

John Malcolm Fraser became Prime Minister in December 1975 when Australian voters gave him the biggest landslide victory in the history of the Federation. From the previous administration, Mr. Fraser has inherited an atrocious economic mess: a staggering budget deficit, an unrealistically overvalued currency, a 14% annual rate of inflation, mounting unemployment, and a demoralized business community. He has already tackled some of these problems with some measure of success; but he has been in power for barely a year, and it&apos;s too soon to see a turn-around.

Jan 1, 1977