Search Documents

By Wolfgang Pitsch

INVESTIGATIONS on the above topic have recently been published by Shapiro and Kraussl and Jana and wayman in this journal and by Kessler and Pitsch.- Parts of the results in these papers are in good agreement with each other but there are also some results which are substantially different. The main points of these differences shall be briefly discussed in this communication. Shapiro and Krauss' measured single-surface traces of the habit planes of reversed austenite plates formed within the martensite crystals and deduced from these measurements two distinct habit planes A = (0.174; 0.309; 0.935) and B = (0.375; 0.545; 0.749) within 3 deg. Kessler and pitsch4 found instead by two-surface analysis7 one habit plane n = {0.23; 0.62: 0.75) with a real scatter of 6 deg. The latter observation of a single habit plane apart from a certain scatter is in agreement with most of the investigations of martensite transformations. The differences between these two results are so great that they cannot be explained by experimental error. The purpose of this communication is to show that the A- and B-poles of Shapiro and Krauss are due to an erroneous interpretation of a single-surface trace analysis. The difficulties in the interpretation of such single-surface trace analyses are due to the high symmetry of cubic lattices, from which it follows that there are in general twenty-four equivalent possibilities of plotting a single-surface trace in a pole figure. All these possibilities must be taken into account, when putting different traces from different plates together in order to construct the habit plane. Alternatively the poles of all the traces may be plotted in a unit triangle. This is done in Fig. 1 with twenty-nine traces of different reversed austenite plates, all of this were measured by Shapiro and Krauss in the same plane of a single martensite ther traces taken from Fig. 13 in the Shapiro and Krauss paper' which were determined by electron diffraction. The traces in Figs. 1 and 2 have to be compared with the habits A, B, and n which are under discussion. Therefore the great circles of the poles A, B, and n are plotted in Figs. 3, 4, and 5 together with a 3-deg scatter region for poles A, B and a 6-deg scatter region for pole n. Comparing Figs. 1 and 2 with Figs. 3, 4, and 5 one finds the statements which

Jan 1, 1969

By Young C. Kim

The use of computer models to design the ultimate open pit limits during feasibility studies as well as during long-range mine planning is becoming an enforced practice in all types of mining, e.g., ferrous, non-ferrous, and coal. As a result, the state of the art in computerized ultimate pit limit design methodologies and associated computing and optimizing techniques has advanced considerably in recent years. Unfortunately, very little has been published to date regarding the preferred ultimate pit limit design philosophy, i.e., optimizing us satisfying, or regarding the modeling approaches being used for different types of orebodies. This paper reviews the current state of the art in various modeling approaches and optimizing techniques that are in use for different types of deposits, through available literatures and personal communications.

Jan 1, 1979

By C. M. Marquardt

Tramp iron and steel moving on a conveyor belt cause small currents to be generated in a coil situated in a strong magnetic field, which are converted to an alternating current and are amplified. The output voltage from the amplifier fires a thyratron with a relay in its anode circuit, which actuates a howler and simultaneously drops a spot of marker material on the belt.

Jan 1, 1950

By C. A. HEILANDG

THERE is a need for men well trained in geo- physical prospecting. Although the number of geophysicists required by the industry in the future cannot be expected to be very great, there will always be a demand for courses on the subject. A number of educational institutions are, therefore, interested in providing instruction in geophysical prospecting. Some institutions will be satisfied with courses in general geophysical prospecting designed to give the geologist fundamental concepts on the comparative merits of the methods and the interpretation of the results. Other institutions will want to give special instructions in theory, field procedure, and interpretation of any or all geophysical methods. In giving such special courses a number of problems will be faced, and it seems to me that such difficulties are easier to overcome in an engineering institution than in a university. A knowledge of basic engineering subjects, such as required of all students in an engineering school, seems to be the best foundation upon

Jan 1, 1930

The Johns Hopkins Press, Johns Hopkins University, Baltimore, Md The Johns Hopkins Press has issued a number of books as The Johns Hopkins University Studies in Geology Five of the studies are paleontological in character; five are on geology: No. 1, The geology of the Corocoro copper district of Bolivia, by J. T Singewald, Jr and E W. Berry, $1 50, 2, The geology and paleontology of the Huancavehca mercury district, by E W Berry and J T Singewald, Jr $1 50, 6, Contributions to the geology and paleontology of South America, by E W. Berry and F M Swartz, 3175, 7, The geology of the Island of Trinidad, B W I, by G A Waring, with notes on the paleontology by G. D Harris, $1 75, 8, Fifty years' progress in geology, 1876-1926 Papers presented at the Geological Conference during the 50th Anniversary of the Johns Hopkins University, $1 50 An additional publication on geology is. Notes on the minerals occurring in the neighborhood of Baltimore, by G H Williams, 25 cents. In the list of Doctors' Dissertations available from the University are found all theses on geology and mineralogy, about 90 in number, from 1886 on Authors of many of these have since made great names for themselves in the fields of geology and mineralogy. Most of the theses have been published as papers by other agencies and, as such, will be found under other headings in this directory

Jan 1, 1933

By D. S. Pye, J. P. Gallus

Successful hydraulic pressure treatment of oil and gas wells that have long producing intervals, multiple pay zones, fluid thief zones, or natural or induced fractures has long been a serious problem plaguing the petroleum industry. High fluid-injection rates, straddle packers, ball sealers, and either liquid or solid additives to the treating fluids are being used to cope with this difficult and costly problem.l-6 The use of ball sealers and straddle packers is limited, in practice, to wells that have been completed with perforated cemented casings or liners. Well stimulation with ball sealers and straddle packers is usually successful as long as the cement remains competent. The other techniques of diverting are used with all types of completions. However, there are two significant disadvantages of the high rate method: excessive horsepower requirements, and the need of large treating-fluid volume. Consequently, most well stimulation techniques that involve diverting depend upon ball sealers or granular materials. Liquid diverting agents, and some of the solid ones in use today, frequently will cause formation damage. On the other hand, the most popular particulate diverting agents often are so soluble in the treating fluid that they become largely ineffective; their particle size is severely reduced as they dissolve while being transported through thousands of feet of pipe to the formation face down hole. In our attempts to deal with the shortcomings of these diverting agents, we experimented with a large variety of potentially suitable deformable materials the solubility of which could be controlled. Following are the criteria for the diverting agent sought: 1. The material must be effective in reducing fluid loss to thief zones, including existing fractures and very high permeability layers in the formation to be pressure treated. 2. The material must have enough strength to bridge under the treating pressure. 3. The material must be insoluble or slowly soluble in the treating fluids so that the particles retain sufficient size to be effective after they reach the formation face. 4. The material must be completely soluble in the produced oil or condensate liquid so that it can be removed readily; it must not cause formation damage. A number of products consisting of various polymers blended with waxes and other solid hydrocarbons were examined. All these materials satisfied the criteria for a diverting agent and also exhibited some degree of plastic deformability. On the basis of initial tests of strength and hardness, several blends of wax and polymer were selected for extensive testing in the laboratory and the field. These compounds have congealing temperatures ranging from 140 to 190F; they are insoluble in water and soluble in oil. They conformed, therefore, to the criteria specified for a theoretically superior diverting agent. Laboratory and field tests were conducted using these wax-polymer materials to demonstrate that the use of a deformable diverting agent can significantly improve fluid diverting performance. Data in this

Jan 1, 1970

By C. H. Fulton

Page Introduction........................... 280 Distillation Products from Reduction of Zinc Ore........... 281 Preliminary Investigations..................... 290 Equilibrium of Reaction Zn + CO2 + ZnO + CO in Temperature Range of Condensation........................ 293 Requisites for Successful Condensation................ 299 Discussion............................ 300 Introduction The study of the condensation of zinc from its vapor was undertaken to shed light on certain problems encountered in large-scale electric zine-furnace work. recently conducted. It is a matter of common knowledge that one of the disadvantages of the arc type, electric zinc furnace, is the production of a large amount of blue powder and proportionately little liquid spelter, for, as stated by Stansfield,l "A notable defect in the electric smelting of zinc ores is the difficulty experienced in obtaining the distilled zinc in the liquid state; ...... when zinc ores are smelted electrically, very little liquid metal is commonly obtained, nearly all of the zinc being in the state of powder." This difficulty was not encountered in the electric furnace used12 the main difficulty being the destruction of the fire-brick lining of the large condenser, in certain parts, and the formation of .some oxide and dross coatings on the condensing surfaces. The reason for these difficulties could readily be explained by the infiltration of air whenever the condenser was changed from one retort base to the other, the zinc absorbed in the fire-brick forming oxide and causing rupture by its expending volume. Two facts, however, tended to disprove this theory for the rupture of the fire-brick lining: first, the large distilling retort, lined with fire-brick, which was shifted from charge to charge on alternate bases at temperatures between 1200 and 1300 C., fully exposed to the air, showed no signs of disintegration whatever; second, marked disintegration in the condenser occurred .only in places that were at tempera-

Jan 1, 1919

• The Venezuelan Trade Mission to the United States announced that Bethlehem Steel Corp. will begin exporting iron ore from its El Pao concession, south of the Orinoco River in Venezuela, in about three months. The ore will be transported by rail from the mines to barges on the Orinoco and transshipped to ore vessels at the coast for shipment to the Sparrows Point, Md., plant. The Latin American business men warned that projected increases in the United States tariff on petroleum imports from Venezuela would force that country into bilateral trade agreements with other countries and would mean drastic curtailment of Venezuelan imports from this country. •Bethlehem, South American Gold and Platinum Co., and U. S. Steel are investigating the possibilities of securing American foodstuff for their South American mining camp commissaries through the International Basic Economy Corp. IBEC buys in quantity to supply its subsidiary companies operating in Venezuela and Brazil. The mining companies will rid themselves of this burdensome task as well as realizing a saving from the bulk purchases of IBEC. •Oliver Iron Mining Co. has begun construction of a fine ore and taconite agglomeration plant at Virginia, Minn. It is expected to be ready in six months. The plant will be used to experiment with the making of clinker cakes and egg-sized lumps by sintering machines and nodulizing kilns respectively; about 1 million tons per year will be produced. • Roof pinning has been adopted at the iron mines of TCI, near Birmingham, to support overlying strata as mining progresses. Favorable results have been obtained in that dilution of the ore has been reduced by 50% which is attributable to this method of supporting the roof. •An American mining engineering team has gone to Turkey for a two-year assignment assisting Turkish government agencies in the $45 million ECA development, mechanization, and construction of cleaning plants for the Zonguldak coal field, 200 miles east of Istanbul on the Black Sea. The group consists of James Beeley, John E. Good, John S. Lambright, David Renshaw, and Charles R. Weir, all of the Paul Weir Co. •Arthur F. Taggart describes a new way of training engineers by emphasis on broad, basic engineering courses on page 460 of this issue. •Lawrence T. Tierney, chairman of the National Bituminous Coal Advisory Council, released a report stating that the increase in oil imports since the latter part of 194$ has caused significant damage to the U. S. fuel economy. It has reduced the strength of and employment opportunities in the coal, domestic petroleum, and transportation industries, as well as in related service and supplier fields. •Women, camels, and donkeys are the beasts of burden of the Sahara, according-to the UNESCO World Review. •Increased demand for magnesium sheet in airplane construction ana other phases of the national security program have led Alcoa to establish a sheet magnesium rolling division at its New Kensington, Pa., works which will begin operation shortly. Novel prospecting methods being used by the USGS in its search for uranium include: shock-mounted instruments in light trucks,. Geiger-counter probes lowered into augur holes, and experimental airborne prospecting.

Jan 4, 1950

By Samuel Wyer

THE art of natural-gas compressing is now over 25 years old, and has grown at practically the same rate as the increase in domestic natural-gas consumers. There are now over 200 natural-gas compressing stations in North America, aggregating more than 320,000 hp. of compressor capacity and representing a property value of more than $22,000,000, and compressing more than 85 per cent. of all the gas used. The age and magnitude of the art make it evident that the use of gas compressors is a recognized integral part and universal custom of the natural-gas business. The public also is not without its rights and vital interests in this problem. Approximately 1,700,000 domestic natural-gas consumers in North America are dependent upon gas compressors for their natural-gas service. That is, if the use of compressors were to be prohibited, the majority of these consumers would be unable to secure adequate natural-gas service. Each consumer represents between four and five persons, and it therefore follows that the comfort and well-being-as far as natural-gas service is concerned-of at least 8,000,000 persons would be affected if the use of natural-gas compressors should be prohibited. These 1,700,000 consumers have invested, in services, house piping, fixtures, and appliances, an average of about $90 each, or an aggregate of $153,000,000, which is much more than the companies' investment in gas compressors. Furthermore, in all cases where the rate paid by the consumers is fair to the gas company-considering the value of the service rendered by the gas company-the consumers are entitled to continued service and protection of the investment they have made on the faith that the gas service would be continued in the future.

Jan 2, 1916

By H. P. Stuwe

It is investigated whether a model of sphere packing permits the computation of the lattice parameters and their variation with concentration in various a phases; it does, except in phases containing silicon. Several observations indicate that a particular role is played by the "E-atoms" in the lattice. THE phase is formed by many alloys of the transition elements.'-' Its structure has been described by Bergman and Shoemaker,5,8 Dickins, Douglas, and Taylor,7 and Kasper, Decker, and elanger.' There are five kinds of crystallographically equivalent positions for the 30 atoms in the unit cell which have been designated by these authors I, 11, 111, IV, and V or, in the same sequence, A, B, C,D, and E, as shown in Fig, 1. For the purposes of the present paper two elements of the lattice will be discussed separately: The lattice planes perpendicular to the c-axis which are made up by the atoms A, B, C, and D and which determine the a-parameter; and the close-packed "vertical rows" of E-atoms which determine the c-parameter. asper,9 and Frank and kasper10 described the a phase and other complex structures as sphere packings. In these papers particular attention is paid to the coordination polyhedra. Lattice positions with an equal number of nearest neighbors are considered equivalent regardless of their crystallo-graphic description. This seems to work very well for the explanation of ordering phenomena in the a phase as far as information on this is available." If the description of the phase as a sphere packing is valid it should be possible to draw two further conclusions: 1) It should be possible to calculate the lattice parameters from the atomic radii of the components, and 2) It should be possible to predict the variation of the lattice parameters with concentration within one phase field. Both points are discussed in this paper. PROCEDURE Measurements of lattice constants were done with a symmetrical back-reflection X-ray camera. With Cr-radiation, about a dozen a1 lines could be observed with most samples. From the (550/710)- and 720-lines the a-value was computed. With this value the c-parameter was calculated from the (333)- and (413)-lines. Finally, the position of all the other lines was computed from the lattice parameters thus obtained. In this way the validity of the indexing could be checked and, at the same time, this proce- dure gave an estimate of the accuracy of the lattice parameters. A correction was made for film shrinkage. The atomic radii used in the computations are the Goldschmidt radii for coordination number 12. Actually, some of the atoms have a coordination number of 14 or 15, but the error thereby introduced is small. * For the computation of lattice constants from the atomic radii an "average atomic radius" of all components was used, i.e., complete disorder was assumed. Although this seems to be true for some systems like OS-Cr,4 it is not true in others.11,13,14 The ordering model, however, which has been suggested by Kasper on the basis of extensive research lets both kinds of atoms contribute to both the ''vertical rows" and the lattice planes perpendicular to them, so that even with ordering of this kind the assumption of complete disorder cannot introduce a very serious error in calculating lattice parameters. RESULTS Bergman and shoemaker6 gave a table of the interatomic distances in the Fe-Cr phase. If we disre-

Jan 1, 1960

By John Mullen

Impingers TWO types of midget impinger apparatus are used at Climax. The Mine Safety Appliances Company's midget impinger (MSA) and the Climax Molybdenum Company's midget impinger (CMC) (Fig. I). The Leiman Brother's No. 25, positive displacement pump is used in the CMC impinger instead of the four-cylinder radial pump that is used in the MSA impinger. With the MSA apparatus it is possible to obtain the proper vacuum by adjusting the needle valve on the vacuum chamber, while with the CMC impinger the proper vacuum is obtained by varying the rate at which the pump is cranked. The Leiman Brother's No. 25 pump is built to displace 0.1 cu. ft. of air per min. when operated at 145 r.p.m. In the CMC impinger this pump is so geared that the required crank speed is approximately 59 r.p.m. Both types of impinger apparatus are equipped with a water gauge mounted on top of the case and they are calibrated and operated in reference to the gauge. The MSA impinger flasks and nozzles are used with both types. Calibrating Impingers A calibrated precision Sargent wet-test meter (Fig. 2) is used in calibrating the impinger apparatus. The apparatus is set up as for taking a sample in the field, except that the hose from the outlet side of the meter is attached to the impinger nozzle. One revolution of the large hand of the meter indicates 0.1 cu. ft. of air displaced. The impinger pump is cranked for one minute, therefore, at a rate that will cause the large hand of the meter to make one revolution. The gauge reading is noted, then the impinger is cranked at this rate for 10 min. and is checked for error. If the meter indicates that more or less than I cu. ft. of air has been displaced, the impinger must be cranked—ither slower or faster according to the error—for another 10 min. and again checked for error. This operation is repeated until the proper gauge reading for a sampling rate of 0.1 cu. ft. per min. has been determined. This gauge reading is used in all sampling operations until the impinger is again calibrated. An impinger is calibrated at least twice each week. MlCROPROJECTOR A Bausch and Lomb model B micro-projector is used (Fig. 3). It consists of a substantial metal base supporting the light source and a microscope. Illumination is provided by a Bausch and Lomb 4.5-amp. arc lamp with mechanical feed. A glass water cell filled with a heat-absorbing and color-filter solution is placed between the arc lamp and the microscope. Two types of solution have been found satisfactory— a 2 per cent solution of copper sulphate or a 2 per cent solution of picric acid and distilled water. This percentage may be varied to give the desired color to the light reflected upon the screen. Any standard microscope may be used. A Bausch and Lomb microscope with

Jan 1, 1946

By James K. Stanley

Preferred orientation, particularly in irons and low-carbon steel, is a phenomenon that is both of considerable importance and theoretical interest. At times it is a liability and at other times an asset. In deep-drawing operations, preferred orientation is extremely undesirable because it necessitates trimming operations and increases scrap loss. Furthermore, oriented metals are likely to crack more easily than randomly oriented material because the forming of symmetrical and unsymmetrical shapes out of preferentially oriented metals and alloys increases the probability of rupture in regions of high stress, owing to differential ductility.' In the electrical industry, on the other hand, preferentially oriented silicon irons are in demand for transformer application because of the improved magnetic permeabilities in the rolling direction.2 This phenomenon of preferred orientation in soft magnetic materials has been responsible for the tremendous improvement in transformer design and construction in recent years. Directional properties in metals have received a great deal of attention in the metallurnical -literature,3-9 in which much of the information reported about orientation has been obtained by conventional methods, mechanicai properties and X-rays. A wealth of data has been obtained and often at a great expenditure of time. The recent introduction of the magnetic torque measurements on ferromagnetic materials provides a very simple and rapid method of evaluating orientation. The judicious use of the method can supply important information, but it should be borne in mind that such studies must be supplemented by X-rays, optical methods,10 and etch and pressure figures" to get a rational understanding of the orientation phenomena. No claims are made that the magnetic torque of evaluating orientation will reveal the behavior of the metal in deep drawing. For this purpose the accepted tests for deep-drawing quality must be used. For a good drawing stock, which must have low impurities, desirable grain size, ductility, strength, hardness, good surface, random orientation, and good recrystallization behavior, it cannot be expected that any simple test will be satisfactory for appraising all the factors. The only factor on which the magnetic method can be used is orientation, which is, of course, of considerable importance. When directionality can cause a 10 to 15 per cent change in tensile strength and a IOO to 300 per cent change in tear length,12 it goes without saying that a reliable as well as rapid method for detecting these changes would be desirable. There are certain inherent advantages in testing orientation by the torque method: The method is rapid with the proper type of equipment; no elaborate preparation of specimens is required—it is only necessary to punch or machine a I-in. disk of the sheet material and insert it into the testing device.

Jan 1, 1944

By James K. Stanley

Preferred orientation, particularly in irons and low-carbon steel, is a phenomenon that is both of considerable importance and theoretical interest. At times it is a liability and at other times an asset. In deep-drawing operations, preferred orientation is extremely undesirable because it necessitates trimming operations and increases scrap loss. Furthermore, oriented metals are likely to crack more easily than randomly oriented material because the forming of symmetrical and unsymmetrical shapes out of preferentially oriented metals and alloys increases the probability of rupture in regions of high stress, owing to differential ductility.' In the electrical industry, on the other hand, preferentially oriented silicon irons are in demand for transformer application because of the improved magnetic permeabilities in the rolling direction.2 This phenomenon of preferred orientation in soft magnetic materials has been responsible for the tremendous improvement in transformer design and construction in recent years. Directional properties in metals have received a great deal of attention in the metallurnical -literature,3-9 in which much of the information reported about orientation has been obtained by conventional methods, mechanicai properties and X-rays. A wealth of data has been obtained and often at a great expenditure of time. The recent introduction of the magnetic torque measurements on ferromagnetic materials provides a very simple and rapid method of evaluating orientation. The judicious use of the method can supply important information, but it should be borne in mind that such studies must be supplemented by X-rays, optical methods,10 and etch and pressure figures" to get a rational understanding of the orientation phenomena. No claims are made that the magnetic torque of evaluating orientation will reveal the behavior of the metal in deep drawing. For this purpose the accepted tests for deep-drawing quality must be used. For a good drawing stock, which must have low impurities, desirable grain size, ductility, strength, hardness, good surface, random orientation, and good recrystallization behavior, it cannot be expected that any simple test will be satisfactory for appraising all the factors. The only factor on which the magnetic method can be used is orientation, which is, of course, of considerable importance. When directionality can cause a 10 to 15 per cent change in tensile strength and a IOO to 300 per cent change in tear length,12 it goes without saying that a reliable as well as rapid method for detecting these changes would be desirable. There are certain inherent advantages in testing orientation by the torque method: The method is rapid with the proper type of equipment; no elaborate preparation of specimens is required—it is only necessary to punch or machine a I-in. disk of the sheet material and insert it into the testing device.

Jan 1, 1944

By H. W. Schadler

The superplastic behavior of low carbon and manganese bearing steels has been evaluated. The results of elevated-temperature stress-strain rate and elongation tests are reported which indicate that high strain rate sensitivity (>0.5) and adequate elongations are achievable in ultrafine-grained steels 1 to 2 p, but at strain rates which are not commercially attractive. It has been demonstrated that the fine grain size is retained after long times and high strains if the temperature is kept within the range of the two-phase (a + ?) field. INTEREST in superplasticity has been stimulated by the desire to: 1) understand the origin of, and mechanisms responsible for, the large uniform elongations observed, and 2) exploit this property for commercial advantage in metal forming operations. Although the Zn-22 wt pct Al alloy presently being studied as a model material1-5 may find application in sheet forming and extrusion, the potential of super-plasticity should best be realized in large tonnage materials, such as steel and aluminum alloys. The degree of superplasticity in low-carbon and manganese-bearing steels has been evaluated. The results of elevated-temperature stress-strain rate and elongation tests on ultrafine grain size material are reported. Avery and Backofen6 and Hart7 have shown that geometrically stable flow leading to extensive uniform elongation in the tension test is associated with high values of the strain rate sensitivity, m, defined: Lozinsky had reported that titanium and zirconium experience permanent deformation if subjected to a constant load and cyclic heating through the temperature range of the phase transformation. Although strain rate sensitivities in excess of about 0.2 had not been reported previously for steel, permanent deformation had been observed11-13 in a wide variety of steels subjected to a constant load and cyclic heating through the temperature range of the a-? phase transformation. Thus by analogy, steel could be expected to exhibit high strain rate sensitivity but only in the a + ? condition. High strain rate sensitivity has been observed at 650°C (a + Fe3C), but not reported as such, by Bailey, Dickenson, and pearson14 in 1931 at a strain rate of about 10-9 per min. It then remained to determine whether high tensile elongations would be observed in a rate-controlled test at constant temperature and at what strain rate strain rate sensitivity values greater than 0.5 would be observed. Since previous experience8 had indicated the importance of fine grain size to realizing high m at reasonable strain rates, it was first necessary to produce an ultrafine grain size and then keep the grains from growing during the test. The results of this investigation show that fine grain size can be readily produced16 and maintained by restricting the temperature of testing to below the ? transus. Further, superplasticity (high m and large uniform elongation) is observed. However, the strain rate range is only marginally useful for commercial forming operations with the finest grain size produced. MATERIAL The material investigated initially was a 1.9 wt pct Mn, 0.42 wt pct C, hot-rolled bar previously used by Low and Turka1015 and available in the laboratory. The 0.500-in. round was cold-rolled to a 0.090-in. flat, annealed for 4 hr at 850°C in argon, air-cooled, and cold-finished to 0.050 in. Subsequently, four additional steels of the compositions given in Table I were investigated to explore the effects of manganese, carbon, and test temperature on the observed stress-strain rate behavior. These steels were melted under argon, cast to 0.75 by 2 by 5 in. slabs, hot-rolled at 850°C, surface-finished to 0.13 in., and cold-finished to 0.050 in. Sheet tensile specimens 0.200 in. x thickness with 1- or 2-in. gage length were cut parallel to the rolling direction. Table I also includes the nominal transformation temperatures for the AISI 1340 and the four experimental steels. EXPERIMENTAL PROCEDURE Production of Fine Grain Size. Ultrafine grain size (1 to 5 p) was considered essential for this studv. Grange16 has described two techniques for producing

Jan 1, 1969

In 1962, minerals beneficiation showed definite signs of coming out of the doldrums into which it has drifted after the uranium boom. Demand by steelmakers for high-grade iron pellets has created the need for concentrating plants to upgrade specular hematite by spiral concentration or flotation and magnetites by magnetic means and flotation. According to a paper given at the AMC annual meeting by C. S. Arms of Pickands Mather, "the shipment of pellets, started in the mid-1950's, has increased to 17.6 million tons in 1961 from North American operations. Many plants already underway will raise this production to about 42 million tons by 1965. This will be a very sizeable percentage of the total iron ore production contemplated by that date." Iron ore concentration methods are gradually raising the assay of pellets into the 65 to 69% Fe range and lowering silica to the 4 to 7% range. Quebec Cartier's Lac Jeannine concentrator went into operation in late 1961 and all grinding units were running by 1962. The Iron Ore Co. of Canada's new Carol Lake plant was started in mid-1962.

Jan 2, 1963

By Klaus-Peter M. Hanke

INTRODUCTION In early 1979 Jim Walter Resources, Inc. (JWR) of Brookwood, Alabama approached TMCI Construction, Inc (TMCI) to make a proposal on a program that involved the sinking of up to 10 ventilation shafts of approximately 6.7 m (22 ft) diameter and ranging in depth from 500 to 700 m (1650 to 2300 ft) for the JWR coal mines in Alabama. At this time TMCI was already constructing the first spiral underground bunker (capacity 2000 tons) in North America for the JWR organization at their No. 4 mine in Alabama. The TMCI proposal was based on the use of the mos modern large diameter shaft boring machine rather than sinking the shafts using the conventional drill blast-muck technique. The proposal was made based o: the experiences by the parent company, Thyssen Schachtbau, which has been using this type of machin in Germany for shaft boring since 1971. As a result of the TMCI proposal JWR issued a purchase order to TMCI for the construction of four 6.7 m (22 ft) diameter, concrete lined, unfurnished ventilation shafts ranging in depth from 500 to 700 (1650 to 2300 ft). An order was thus placed with WIRTH Machinen- and Bohrgeraete Fabrik GmbH, in Germany for the manufacture of a model 650/850 E/Sch "Schachtbohrmaschine" (Vertical Shaft Borer = V-mole which arrived on site in Alabama in early 1981. The first V-mole GSB 450/500 was introduced in Germany in 1971 and was capable of enlarging in one step a pre-drilled 1.2 m (4 ft) pilot hole to 4.5 - 5.0 m (14.7 - 16.4 ft). This machine has sunk 9 staple shafts and deepened one surface shaft for a total of 2360 m (7740 ft) of shafts. On the last shaft boring operation in 1978 the machine was converted as an experiment to drill without a pilot hol using a hydraulic pumping system to remove the cutting debris. A second generation machine, the SB VI 500/650, was introduced in 1977 for enlarging the pilot hole to a range of 5.0 - 6.5 m (16.4 - 21.3 ft) diameter. This machine is still in operation and has already drilled well over 2000 m (6500 ft) of shaft. The third generation of V-mole, the SB VII 650/85( for diameters from 6.5 to 8.5 m (21.3 to 27.9 ft) was: commissioned in May 1980 and has been used for two surface shaft deepenings totalling 606 m (1990 ft) with another scheduled for 1982. The main advantages favouring the use of such V-moles were identified as: 1) A reduction in manpower to the crew required in a conventional shaft sinking operation. 2) A considerable reduction in time to complete a shaft compared to conventional techniques. 3) The use of the V-mole eliminates many of the hazards encountered in conventional sinking. Based on the successful performance of the first three V-moles in Germany, Thyssen Schachtbau decided to employ this principle abroad. In 1980 a second machine of the third generation was built and is now operated by TMCI Construction, Inc. in Alabama. The first shaft was completed at the end of 1981 and this paper describes the method of operation including some unique aspects not attempted on prior V-mole operations and some of the statistics arising out of the experiences during the first shaft boring operation. THE NO. 7 MINE FAN SHAFT SITE Jim Walter Resources, Inc. was formed in 1970 to exploit the coal field in Alabama on the southern tip of the Appalachian coal field. The coal reserves amount to around 650 million tons of mainly good quality coking coal of which about 350 million tons are to be extracted over the next 30 years. Shaft sinking and preparatory work began in 1972, and at present 6 mines are producing around 5.4 million t.p.a. Annual production is to expand to 10 million t.p.a. as soon as possible, and the ventilation shafts to be sunk by TMCI play a vital role towards attaining this goal. The first shaft site is located at the No.7 mine, near Brookwood, Alabama. The actual location of the shaft relative to the production shafts is shown on the mine plan (Fig. 1), which also shows the room-and-pillar extraction system used at present. The mine plan further shows the conveyor route used for the muck removal. The geological survey showed that the strata consisted of horizontal layers of mainly sandstone, sandy shale and shale interspersed with several coal seams. The seam being extracted at the No. 7 mine is a combined seam made up of the Blue Creek and Mary Lee seams at a depth of 513 m (1682 ft) and having an average seam thickness of about 2 m (6 ft). At the beginning of September 1980 the surface site preparation and pre-grouting work was completed by JWR, and TMCI was able to commence with Stage I of the shaft sinking program - the drilling of the pilot hole.

Jan 1, 1982

By Freeman Bishop

Having obviously cleared the way for fast confirmation by the Senate Interior Committee, the Administration recently named Elburt F. Osborn, vice president of Penn State University, as director of the Bureau of Mines. Interior Committee Chairman Henry M. Jackson (D of Wash.) has moved hearings on the nomination right along, forecasting that they will end in a confirmation. Dr. Osborn not only made a good impression on the Committee, he also made it amply clear that he would be the boss of his job and have right-hand aides to help straighten out conflicts stemming from recently enacted health and safety regulations for miners. Mining engineers in the field hope this clarification can come soon. They are frankly fed up with local, state, regional and national overlapping of restrictions.

Jan 1, 1970

By C. A. Pierce

Underground operations of the United States Potash Co. at its mine near Carlsbad, N.M., have been continuous since the property was opened about five years ago. Approximately one million tons of potash has been mined and two shafts have been sunk, each to a depth of about 1000 ft. Outstanding in the company's operations is the fact that not a single blasting accident has occurred during the aforesaid period. The purpose of this paper is to describe the blasting practice that has made possible the achievement of this accident-prevention record. The mining method employed in extracting the thick horizontal bed of potash may be described as a double-entry room-and-pillar system. Mine development is kept well in advance of extraction operations, and a three years' supply of ore, at least, is always available. Limits of the orebody have not been determined, and in the present system of mining headings are advanced by a "shortwall" method. This was the first potash ore bed developed in the United States. The nature of the deposit, therefore, was unknown, and it was deemed expedient to outline a conservative mining policy. Later, when more is known about the deposit and certain control ascertained, a "longwall" panel retreating method may be found advisable. The necessity for a domestic supply of potash became a national issue previous to and during the World War. The United States Government came to realize that this country should not be dependent upon foreign sources of potash, and began extensive explorations in many parts of the country, seeking an orebody that would meet the exacting requirements of the domestic market. The Department of Interior, through the Geological Survey and Bureau of Mines, made every effort to determine the location of potash deposits and encouraged their exploitation by private capital. Through the combined efforts of the Department of Interior and private industry, the deposit now being worked by the United States Potash Co. was discovered and brought into production.

Jan 1, 1937

By E. C. W. Perryman

The recovery of X-ray line broadening, hardness, and electrical resistivity from cold worked AI-Mg alloys has been investigated. The results, together with those from density measurements, suggest that magnesium atoms freeze in the excess vacancies formed by cold working, and that this affects the climb of dislocations during the recovery process. PREVIOUS work1, " has shown that while 1 pct Mg increases the activation energy for recrystalliza-tion, it decreases the activation energy for the recovery of mechanical properties and decreases the subgrain size both after cold working and annealing. A similar result has been reported by Varley2 for an A1-2 pct Mg alloy. With plastic deformation at high temperatures, McLean and Farmer' and Rachinger have found that magnesium appears to retard the motion of dislocations and, furthermore, they find little or no effect of magnesium on the size of subgrains formed during high temperature deformation. In view of the apparent contradictions as to the effect of magnesium on subgrain size, the recovery process in Al-Mg alloys has been investigated more thoroughly by studying the annealing out of X-ray line broadening, hardness, and electrical resistivity from alloys cold worked at room temperature. Material Used—The chemical analyses of the alloys are given in Table I. Fabrication—The material used was cold rolled 20 pct at room temperature, the grain size prior to the last cold rolling operation being similar to that used in previous work; i.e., 230. The experimental procedure for annealing, determination of X-rav half-veak breadth. hardness measurement, electEica1 resistivity, and density and metallographic examination was exactly the same as previously described." Variation of X-Ray Half-Peak Breadth with Annealing Time—Isothermal annealing curves at 100°, 200°, and 250°C were obtained for material cold worked 20 pct. The half-peak breadth of the (333) Ka, line directly after cold working is shown as a function of magnesium content in Fig. 1. Only with the 2.87 pct Mg alloy was overlapping of the a, and n.. reflections observed to any appreciable extent. To separate these, Rachinger's method' was used. Typical isothermal annealing curves are shown in Figs. 2 and 3 for 100" and 200°C, respectively. These curves are similar to those obtained previously for super-purity aluminum except that the

Jan 1, 1957

By D. E. Thomas

Oxidation rate constants were determined for Cu-Pd and Cu-Pt alloys as a function of alloy composition and temperature. Reaction products were identified. Relationship between oxidation rate constants and diffusion constants in the reaction zones is discussed. THE mechanism of oxidation of alloys is consider--'¦ ably more complex and not so well understood as that of pure metals. The oxidation of a one-phase binary alloy of which one component is a noble metal should logically be the simplest case of alloy oxidation, for in this case one is concerned presumably only with the oxidation of the base metal and the diffusion process by which it reaches the reaction site. This had led a number of investigators to study such systems. Probably the earliest work was that of Tammann and Rienacker' on the tarnishing of Cu-Au alloys at temperatures up to 300°C. These alloys oxidize according to the logarithmic law, that is, the film thickness is proportional to the logarithm of the time. The rate of film formation was found to decrease with increasing gold content. Raub and Engel² investigated the oxidation of Au-Cu, Cu-Pd, Au-Ag-Cu, Au-Pd-Cu, and Ag-Pd-Cu alloys at 750°C in air. These alloy systems form a continuous series of solid solutions at the temperature of oxidation with the exception of those containing silver. Au-Cu alloys oxidize parabolically, the rate constant decreasing slowly with increasing gold content up to about 15 atomic pct* Au, and more rapidly thereafter. An alloy with 14 pct Cu forms only a very thin layer of CuO on the surface and probably also a subscale.† Alloys containing more than 14 pct Cu have scales consisting of CuO and subscales of Cu,O embedded in nearly pure gold. The Cu-Pd alloys obey the parabolic law except for slight deviations for alloys containing 53 and 84 pct Cu. The overall oxidation rate decreases rather smoothly with increasing palladium content. A scale consisting of a thin layer of CuO and a thick layer of Cu²O and a subscale of Cu²O embedded in nearly pure palladium was observed for alloys containing 84, 53, and 30 pct Cu. An alloy with 19 pct Cu formed only a subscale of CuO embedded in nearly pure palladium, and an 8 pct Cu alloy formed only a thin film which was presumed to be PdO. The ternary alloys considered by Raub and Engel oxidized in much the same way as did the binaries. Wagner and Grunewald³ found that Ni-Au alloys, oxidized at 900°C in oxygen, formed a scale of NiO and a subscale containing NiO and gold. The overall oxidation rate increases with increasing gold content, passes through a maximum and then decreases to zero for pure gold. The fact that gold increases the oxidation rate was attributed to "pores" in the scale. Kubaschewski' investigated the air oxidation of alloys of platinum or gold with up to 10 pct Cu or Ni at temperatures in the range 300" to 1550°C. Parabolic behavior was noted for all alloys except Au-Ni, with rates decreasing in the order Au-Cu, Au-Ni, Pt-Ni, Pt-Cu. The diffusion coefficients for the latter three systems are known, and they decrease in the same order. However, activation energies for the oxidation of these alloys do not agree with the activation energies for diffusion in the respective alloy systems. Kubaschewski and Goldbeck7 nvestigated the oxidation of Ni-Pt alloys in air at temperatures of 600"

Jan 1, 1952