Search Documents

By D. M. Schuster, E. Scala

The elastic effects occurring in the matrix of a composite reinforced by discontinuous fibers were studied by means of photoelastic techniques. A hirefringent plastic was employed as the matrix material with high-strength a Al2O3 whiskers as the reinforcing fibers. It was found that for whiskers aligned parallel to the tensile load direction: (I) Matrix reinforcement occurred along the length of the whisker to within about 5 diameters of the whisker tip for a length to diameter ratio, L/D, of 40. (2) Significant stress concentrations were created in regions immediately surrounding the tips; the fine as-formed tapered ends exhibited the minimum stress concentration whereas the square-ended whisker produced relatively high values, K r 2.5 for L/D = 40. (3) The axial and radial stress distributions could he determined quantitatively; the stress distribution at the whisker-matrix interface was in general agreement with theoretical calculations. (4) The highest source of stress concentration occurred at points of fracture in whiskers which had ruptured after incorporation into the composite. Whiskers aligned perpendicular to the load direction neither reinforced nor caused appreciahle stress concentrations in the matrix. ThE properties of composites have generally been formulated empirically on the basis of macroscopic tests. There are still many questions concerning the mechanical and chemical interactions occurring at the interface between the reinforcing fiber and its matrix. Continuously reinforced plastics and dispersion-hardened metals represent the two extremes of composite reinforcement. Whether artificially produced or formed in situ, the whisker composite falls between these two extremes and is an example of discontinuous fiber reinforcement. The effect of fiber shape, size, surface condition, and end configuration on the stress distribution in the matrix is important since the presence of stress concentrations, especially in any high-strength, thin-wall structure, could become the cause of catastrophic failure. DOW,' in his theoretical discussion of discontinuous fiber reinforcement, has pointed out that appreciable stress concentrations occur at the tips or ends of the reinforcing fibers. It is the purpose of this study to examine directly, by means of the photoelastic technique, the stresses which occur in the vicinity of a discontinuity or whisker tip and to measure qualitatively and quantitatively the effects of whisker geometry when embedded in a birefringent matrix material. The use of sapphire (a A1,O3) whiskers was decided upon as the reinforcing agent because of their high elastic modulus (E- 60 X 106 psi) and in some cases strengths in excess of one and a half million psi. Sapphire whiskers are of further practical interest since they retain large fractions of their strength up to temperatures approaching the melting point (3720oF).2 The whiskers were grown, by the vapor-phase reaction commonly employed,3 as part of this study to insure a physically uniform supply. Tensile and bend tests were performed to verify that the whiskers were of the expected ultra-high strength. The high-strength whiskers can be identified and selected from the combustion boats by surface perfection, shape, and size; otherwise, strength values can vary by a factor of ten or more. Macroscopic defects are quite common on the surface of large bladed whiskers and the principal experiments were conducted with hexagonal whiskers of about 0.002 in. diameter and lengths ranging from 0.1 to 0.4 in. Upon completion of these two phases of the experiment, several birefringent resins were evaluated. A plastic, developed by Zandman,4 which is supplied by the Budd Co., was found most suitable and was used as the matrix material for the whisker composite throughout the study. It has a sensitivity of 60.5 lb per in. order, calibrated in tension and cures without introducing residual stresses. Young's modulus for this matrix material is 430,000 psi in the fully cured condition. Since good wetting and bonding between the sapphire and the matrix material is essential to the interpretation of the results, a wettability test was performed. The contact angle was measured to be 168 deg where perfect wetting is defined as 180 deg; therefore, the Budd Plastic wets the sapphire

Jan 1, 1964

By Edwin A. Zink, Gerald P. Zink, John E. Wolgamott

Recent advances in high-pressure water technology can be effectively employed in underground mining. The new equipment is based on standard industrial water cleaning hardware and is compatible with conventional mining techniques. Three viable applications are addressed: rock drilling, hole notching, and rock bolting. Highlights of test results are presented that were obtained in several underground mines during the last two years of development work.

Jan 1, 1982

By Robert D. Pehlke, Kazuhisa Okajima

The activity of zinc in dilute liquid lead alloys containing small additions of silver and gold has been measured using a multielectrode galvanic cell with a fused chloride salt electrolyte. The range of temperatures studied in the Pb-Zn-Ag system was 550" to 670°C and in the Pb-Zn-Au system was 680" to 800°C. The interaction parameters between zinc and the precious metals in the respective temperature ranges are ThE lead-rich corners of the Pb-Zn-Ag and Pb-Zn-Au ternary systems are of considerable industrial importance. The use of zinc additions for the desilvering The results of this investigation have Provided a senzi-quantitative determination of the liquidus phase boundaries in the lead-rich corner of these ternary diagrams. of liquid lead either by the Parkes process or by the more recent Williams continuous process is an important refining phase of lead production.1 Several in-ve~ti~ations~-~ have been carried out on the Pb-Zn-Ag system with the hope of improving the efficiency of refining lead in this manner. The addition of zinc also provides a means for separating gold from lead. Since gold is eliminated more easily than silver, a two-stage removal of gold and silver is possible.8'7 The thermodynamic interactions between zinc and these precious metals in dilute solution in liquid lead

Jan 1, 1968

By N. A. Stockett

SOUTHEAST Missouri is the largest and oldest lead-producing district in the United States. For the year 1941, the statistical picture of pig-lead production, stated in short tons (partly estimated by the Engineering and Mining Journal) is as follows. [Tons World production 2,000,000 United States production 460.000 Southeast Missouri production 242,000] The consumption of primary lead in the United States in 1941 was approximately 900,000 tons, or almost double the country's production. The largest previous year's consumption in the United States was 718,000 tons, in 1926. The largest quantities of lead are used for cable sheathing, storage batteries and white lead. During 1941 tetraethyl lead for auto and aviation gasoline consumed 50,000 tons of lead. The entire lead production of Southeast Missouri is now mined by the St. Joseph Lead Co., whose dominant position as the largest producer in the United States of lead directly from ores is best shown by the fact that in 1941 it produced approximately 31 per cent of the lead production of the United States from its mines in southeast Missouri, where 22,000 tons of ore, averag¬ing over 3.00 per cent lead, is mined per working day. It is known that lead was mined at Mine La Motte, Madison County, Missouri, by Renault in 1723. Other white men and Indians probably did some mining prior to that time. Since 1865, the recorded production to Jan. 1, 1942, shows that the St. Joseph Lead Co. and the various other companies that have operated in St. Francois County mined lead ore, which, after milling and smelting losses produced 5,00,000 short tons of pig lead. About 95 per cent of the present lead production of Southeast Missouri is mined in St. Francois County. The northern part of this area is 60 miles south of St. Louis. The remainder of the lead is obtained at Mine La Motte, about 25 miles southeast from the center of the producing area in St. Francois County. PROSPECTING In this district, most of the ore is discovered by surface and underground diamond drills and by prospect drilling underground with rock drills. Each 2-ft. length of the cuttings from these Jackhamer prospect holes is assayed for lead. These holes are marked and the records are entered on maps. It has been found that close drilling--100-ft. centers of holes, and sometimes less-is necessary in order to locate most of the smaller commercial ore bodies, many of which previously had been missed by drilling the areas with holes spaced 200-ft. centers or more.

Jan 1, 1943

By Bayard Morrow

THE copper-bearing ores concentrated at the Anaconda plant of the Anaconda Copper Mining Co. are principally a mixture of copper and iron sulfides associated in a gangue consisting of quartz, lightly altered granite and feldspars, with sphalerite and galena and more rarely barite and hubnerite as accessory minerals. The predominant sulfide is pyrite. The copper minerals present are: chalcocite, bornite (Erubescite), enargite, chalcopyrite, covellite, tetrahedrite and some tennantite. Normal concentrator practice removes a slime prior to ball-mill grinding. The deslimed ore is ground to approximately 10 per cent plus 65 mesh for flotation. Two selective flotation circuits are used, one for deslimed ore and one for slime. The metallurgical results obtained are shown in Table 1.

Jan 1, 1933

By W. T. Lankford, Low J. R., Gensamer M.

The problem of sheet metal formability is one which has received a vast amount of attention during recent years. In spite of the great amount of study and experimental work which has been devoted to this problem, many of its fundamental aspects are still not well understood. No generally satisfactory test has been developed which is capable of providing a reasonably adequate evaluation of sheet metal formability, particularly in borderline cases. Anomalies persistently arise in which a lot of supposedly satisfactory material exhibits excessive breakage when formed. This lack of suitable technological tests greatly hinders the design of new parts and the substitution of new materials in parts of existing design, frequently necessitating considerable costly trial and error experimentation on an actual production basis. When, at the beginning of World War 11, it became apparent that mass production methods of forming would bc required in the aircraft industry if the large numbers of military aircraft needed were to be supplied, renewed attention was focussed on the problem of sheet metal formability. It was widely recognized that the formability requirements placed on sheet metals had been steadily increasing in severity through the years, especially as greater and greater emphasis was placed on streamlined designs with the resultant freer application of doubly curved surfaces. The recent advent of several new high strength aluminum alloys of more limited formability than some of the older alloys also served to emphasize the need for new approaches to the problem. It seemed evident that progress in the technology of sheet metal forming would depend to a great extent on the development of more reliable criteria for the evaluation of formability. Although the problem is admittedly very complex, the most logical approach appeared to be through studies of the fundamental material properties of sheet metals, especially under complex stress conditions simulating those prevailing in actual forming operations. Most previous investigations have failed to make full use of existing knowledge of fundamental material properties, and in many instances have attempted correlations with properties which are now recognized as being ambiguous in nature. This investigation was undertaken, therefore, with the aim of developing methods for the study of the flow and fracture of sheet meta1s under combined stresses, and of making use of such methods as might be developed in

Jan 1, 1947

By Low J. R., Gensamer M., W. T. Lankford

The problem of sheet metal formability is one which has received a vast amount of attention during recent years. In spite of the great amount of study and experimental work which has been devoted to this problem, many of its fundamental aspects are still not well understood. No generally satisfactory test has been developed which is capable of providing a reasonably adequate evaluation of sheet metal formability, particularly in borderline cases. Anomalies persistently arise in which a lot of supposedly satisfactory material exhibits excessive breakage when formed. This lack of suitable technological tests greatly hinders the design of new parts and the substitution of new materials in parts of existing design, frequently necessitating considerable costly trial and error experimentation on an actual production basis. When, at the beginning of World War 11, it became apparent that mass production methods of forming would bc required in the aircraft industry if the large numbers of military aircraft needed were to be supplied, renewed attention was focussed on the problem of sheet metal formability. It was widely recognized that the formability requirements placed on sheet metals had been steadily increasing in severity through the years, especially as greater and greater emphasis was placed on streamlined designs with the resultant freer application of doubly curved surfaces. The recent advent of several new high strength aluminum alloys of more limited formability than some of the older alloys also served to emphasize the need for new approaches to the problem. It seemed evident that progress in the technology of sheet metal forming would depend to a great extent on the development of more reliable criteria for the evaluation of formability. Although the problem is admittedly very complex, the most logical approach appeared to be through studies of the fundamental material properties of sheet metals, especially under complex stress conditions simulating those prevailing in actual forming operations. Most previous investigations have failed to make full use of existing knowledge of fundamental material properties, and in many instances have attempted correlations with properties which are now recognized as being ambiguous in nature. This investigation was undertaken, therefore, with the aim of developing methods for the study of the flow and fracture of sheet meta1s under combined stresses, and of making use of such methods as might be developed in

Jan 1, 1947

By Lloyd B. Underwood

Dr. Gardener, in Chapter 2, has presented a comprehensive state-of-the- art review of site investigations For tunneling. Nearly all of the techniques he discussed will also be required for future site investigations. Therefore, this chapter will be devoted to a few rather new exploration techniques plus ideas for improving some of the present-day methods. In March 1962, the first symposium on "Remote Sensing of Environment" was held at the University of Michigan.l Since that time, four additional symposiums have been held at the same University. Also, the technical Literature has recently included a number of articles on remote sensing techniques. A recent one appeared in the February 1968 issue of Materials Research and Standards.Vt was entitled "Developments in Remote Sensing Applicable to Airborne Engineering Surveys of Soils and Rocks," and was written by Dana C. Parker. Mr. Parker predicts that aerial reconnaissance will someday supplant soil augers, rock drills, surface reconnaissance, and geophysical surveys as the engineer's primary means of obtaining information about soils and rocks. He states, "The engineer wishing to survey a route or a site or to locate rock and soils suitable for construction projects will be able to push some buttons in an airplane and record all the data required for determining the relevant conditions. In a short time after he returns to earth with his rolls of film and charts, he will be able to reduce and analyze the data by partially computerized techniques and to compile a concise and comprehensive engineering report that gives all the relevant information about rocks, soil, water, and vegetation in the area he surveyed. Most important he will feel as confident with his recommendations, derived primarily from image characteristics and spectral power distributions, as his predecessors did with recommendations based on more tangible evidence obtained from drill cores and surface reconnaissance." The airborne sensors for engineering surveys of soils and rocks are those that sample some electromagnetic property of the materials that com- prise the terrain and cover its surface. In addition to cameras, these include

Jan 1, 1970

By A.A. Gustafson

In diamond or churn drilling for the prospecting of ore bodies, two products can be used for quantitative analyses; i.e., the core and the cuttings, or sludge. Some operators prefer an assay of core; others insist that the sludge be sent for analysis. Both must recover the sludge for check samples or for assays if there is no core recovery for any particular section of the diamond-drill hole. The Freeport Sulphur Co. found that numerous cumbersome sludge boxes or barrels were inconvenient and delayed drilling. The sludge settled slowly in the ordinary shallow, rectangular diamond-drill boxes and its total removal from the container was difficult, time-consuming and unsatisfactory; and sampling of deposits of which the metal contents are easily concentrated, as in ores containing cinnabar, gold and silver, is subject to error if the boxes are not thoroughly cleaned. Mr. Charles Ballard, dredge superintendent at Freeport's operation at Grande Ecaille, Louisiana, developed a portable cone while he was in charge of prospecting a mercury property near Tonopah, Nevada, in 1940. Ballard later improved the design while the settler was being used at a manganese property in New Mexico. The operation is based on the "free settling" of comminuted particles in a quiescent liquid. The ordinary sludge box discharges over a lip 8 to 12 in. wide and consequently the water has sufficient velocity so that the discharge water is never clear. The cone settler used by Free-port Sulphur Co. discharges over the entire circumference, which gives a discharge ltp of 9 ft. in the size of cone used at the cinnabar and manganese prospects. Consequently, the velocity of the discharge water is slow enough so that all fine material settles and the discharge water is clear. When the drilling of a sample interval is complete, the sludge can be drawn off by the time the driller is ready to cut another sample. Thus, only one cone is needed per drill. The cone has been used by Freeport successfully in churn-drilling a manganese deposit, in diamond-drilling a mercury deposit, and in diamond-drilling a deposit of ore containing tin, copper, gold and silver. The cone is greatly superior to the old methods of collecting sludge and is now used on all Freeport drilling campaigns in the western states, both for surface and underground drilling. Fig. I shows the important details of a cone designed for average operating conditions, 30 in. in diameter and 36 in. high. Abnormal conditions may require some revisions in design. Fig. 2 shows a working drawing. A hose or pipe larger than the one used to convey water from the pump to the swivel head of the string of rods is connected to the stuffing box at the collar of a diamond-drill hole, The usual T-connection is used. It is not necessary to use a stuffing box if the top of the cone can be placed lower than the collar of the hole. Then the return water and cuttings can be made to flow by gravity. This hose or pipe discharges the cuttings of the drill bit and the return

Jan 1, 1943

By A. A. Gustafson

IN diamond or churn drilling for the prospecting of ore bodies, two products can be used for quantitative analyses; i.e., the core and the cuttings, or sludge. Some operators prefer an assay of core; others insist that the sludge be sent for analysis. Both must recover the sludge for check samples or for assays if there is no core recovery for any particular section of the diamond-drill hole. The Freeport Sulphur Co. found that numerous cumbersome sludge boxes or barrels were inconvenient and delayed drilling. The sludge settled slowly in the ordinary shallow, rectangular diamond-drill boxes and its total removal from the container was difficult, time-consuming and unsatisfactory; and sampling of deposits of which the metal contents are easily concentrated, as in ores containing cinnabar, gold and silver, is subject to error if the boxes are not thoroughly cleaned. Mr. Charles Ballard, dredge superintendent at Freeport's operation at Grande Ecaille, Louisiana, developed a portable cone while he was in charge of prospecting a mercury property near Tonopah, Nevada, in 1040. Ballard later improved the design while the settler was being used at a manganese property in New Mexico. The operation is based on the "free settling" of comminuted particles in a quiescent liquid. The ordinary sludge box discharges over a lip 8 to 12 in. wide and consequently the water has sufficient velocity so that the discharge water is never clear. The cone settler used by Freeport Sulphur Co. discharges over the entire circumference, which gives a discharge lip of 9 ft. in the size of cone used at the cinnabar and manganese prospects. Consequently, the velocity of the discharge water is slow enough so that all fine material settles and the discharge water is clear. When the drilling of a sample interval is complete, the sludge can be drawn off by the time the driller is ready to cut another sample. Thus, only one cone is needed per drill. The cone has been used by Freeport successfully in churn-drilling a manganese deposit, in diamond-drilling a mercury deposit, and in diamond-drilling a deposit of ore containing tin, copper, gold and silver. The cone is greatly superior to the old methods of collecting sludge and is now used on all Freeport drilling campaigns in the western states, both for surface and underground drilling. Fig. I shows the important details of a cone designed for average operating conditions, 30 in. in diameter and 36 in. high. Abnormal conditions may require some revisions in design. Fig. 2 shows a working drawing. A hose or pipe larger than the one used to convey water from the pump to the swivel head of the string of rods is connected to the stuffing box at the collar of a diamond-drill hole. The usual T-connection is used. It is not necessary to use a stuffing box if the top of the cone can be placed lower than the collar of the hole. Then the return water and cuttings can be made to flow by gravity. This hose or pipe discharges the cuttings of the drill bit and the return

Jan 1, 1943

By A. A. Gustafson

In diamond or churn drilling for the prospecting of ore bodies, two products can be used for quantitative analyses; i.e., the core and the cuttings, or sludge. Some operators prefer an assay of core; others insist that the sludge be sent for analysis. Both must recover the sludge for check samples or for assays if there is no core recovery for any particular section of the diamond-drill hole. The Freeport Sulphur Co. found that numerous cumbersome sludge boxes or barrels were inconvenient and delayed drilling. The sludge settled slowly in the ordinary shallow, rectangular diamond-drill boxes and its total removal from the container was difficult, time-consuming and unsatisfactory; and sampling of deposits of which the metal contents are easily concentrated, as in ores containing cinnabar, gold and silver, is subject to error if the boxes are not thoroughly cleaned. Mr. Charles Ballard, dredge superintendent at Freeport's operation at Grande Ecaille, Louisiana, developed a portable cone while he was in charge of prospecting a mercury property near Tonopah, Nevada, in 1940. Ballard later improved the design while the settler was being used at a manganese property in New Mexico. The operation is based on the "free settling" of comminuted particles in a quiescent liquid. The ordinary sludge box discharges over a lip 8 to 12 in. wide and consequently the water has sufficient velocity so that the discharge water is never clear. The cone settler used by Free-port Sulphur Co. discharges over the entire circumference, which gives a discharge ltp of 9 ft. in the size of cone used at the cinnabar and manganese prospects. Consequently, the velocity of the discharge water is slow enough so that all fine material settles and the discharge water is clear. When the drilling of a sample interval is complete, the sludge can be drawn off by the time the driller is ready to cut another sample. Thus, only one cone is needed per drill. The cone has been used by Freeport successfully in churn-drilling a manganese deposit, in diamond-drilling a mercury deposit, and in diamond-drilling a deposit of ore containing tin, copper, gold and silver. The cone is greatly superior to the old methods of collecting sludge and is now used on all Freeport drilling campaigns in the western states, both for surface and underground drilling. Fig. I shows the important details of a cone designed for average operating conditions, 30 in. in diameter and 36 in. high. Abnormal conditions may require some revisions in design. Fig. 2 shows a working drawing. A hose or pipe larger than the one used to convey water from the pump to the swivel head of the string of rods is connected to the stuffing box at the collar of a diamond-drill hole, The usual T-connection is used. It is not necessary to use a stuffing box if the top of the cone can be placed lower than the collar of the hole. Then the return water and cuttings can be made to flow by gravity. This hose or pipe discharges the cuttings of the drill bit and the return

Jan 1, 1943

By Paul. D. Merica

I LIKE to look upon the award this year also as a recognition of the importance of metallic materials of construction to the engineer and of the active progress which I believe is continually being made in almost all branches of that field today. It has been said that metals are the material backbone of industry and technology. Well in that case, I suppose we metallurgists are industry's bonesetters. And it is possibly not inappropriate that we should occasionally give some atten¬tion to those bony structures of our industrial activities upon which engineers in other fields hang their manifold and striking creations. What is going on in the field of metals development? Well, in the first

Jan 1, 1938

By Joseph E. Pogue

THERE are two methods employed in the development of oil pools. The older and dominant method is one in which the primary object is the protection of the underground deposit from drainage through competing wells, and considerations of efficiency of extraction and cost of production are subordinated thereto. The newer and less prevalent method is one in which maximum efficiency and minimum cost are the first objectives and developments to these ends may proceed undisturbed by the exigencies of competitive drainage. The second method has developed mainly in pools under single ownership and the term "unit operation" has come to be applied to this procedure. A single ownership, however, is not essential to the method, for unity of operation may be achieved by agreement under split ownership, or even by a concert of enlightened purpose. There are examples of unit operation where neither the ownership nor the management is a unit, but merely where unity of procedure has been attained, as is the case of the Yates pool. .Throughout this paper unit operation is used in its broad sense without implying sole ownership or single management, although unit operation is more conveniently attained where these conditions are present.

Jan 1, 1930

By Charles D. Hoyt

T IME studies and cost accounting were combined to increase the efficiency of the overall mining method and thereby reduce costs at the Titania mine of the National Lead Co. in southern Norway about 70 miles southeast of Stavanger. From these studies a more effective drilling system was developed, standards were adopted for setting base pay rates, shrinkage stoping was abandoned for open stoping, a new mechanical loading chute was adopted, and the loading and haulage system was changed. Ore minerals at the Titania mine are ilmenite and magnetite; gangue minerals are plagioclase and hyperstene with accessory minerals of biotite, pyrite, chalcopyrite, and spinel. The average content of the ore is 17 pct TiO2 and from 20 to 25 pct iron. The ilmenite crystals contain microscopic lamels of hematite, making it impossible to obtain a high TiO2 content in the concentrate. An ilmenite concentrate with 44 pct TiO2 and 36 pct Fe, and a magnetite concen-

Jan 9, 1950

By D. O. Hobson, J. O. Stiegler, C. J. McHargue

The effects of alloy composition, deformation temperature, heal treatment, ad inlerstilial contamination on the occurrence of deformation twins were studied. The twinning transition temperature varied with composition and was a maximuni of 140°C for the 40 pcl V composition. Tire remperature range of the transition was very narrow. Alloys of 20 to 70 pet V could he cold-rolled and exhibited profuse twinning. The alloys which did not twin at room temperature (10, 80, and 90 pel V) could plot be cold-rolled. Oxygen additions systematically lowered the transition temperatures for all vanadium contents. The transition temperature for a 30 pet V alloy increased with annealing temperature, apparently due to changes in dislocation density and configuration. Twinning did not nucleate fracture in any specimen in the 20 to 60 pet V composition range. THERE is great current interest in the refractory metals and alloys as structural materials. An important factor in considering the ductile-brittle behavior of such materials is the role of mechanical twinning as a deformation mechanism. Mechanical twins have been observed after deformation at low temperatures or at high loading rates in the pure metals iron,1 vanadium,2,3 columbium,4,5 tantalum,6 Chromium,7 molybdenum,8 and tungsten.9 Binary alloys in which mechanical twins have been observed include: iron with silicon,10 phosphorous," or aluminum;12 and chromium, molybdenum, or tungsten with rhenium.13-17 The increase in low-temperature ductility obtained by alloying the Group VI-A elements with rhenium is very important with regard to fabricability, and there has been considerable effort to understand the so-called '(rhenium effect". Factors suggested to explain this effect include:'' 1) increase in solubility of interstitial impurities with alloying (electronic effect): 2) changes in the nature of grain boundary phases; 3) changes in interfacial energies of grain boundaries and stacking faults: and 4) promotion of twinning. Although an outstanding characteristic of these alloys is the profuse twinning that accompanies low-temperature deformation, most studies of the rhenium effect have been concerned with the other factors. During recent studies of refractory-metal alloys, it was noted that solid solutions of columbium and vanadium exhibited high hardness and strength at room temperature and elevated temperature and, surprisingly, also showed considerable ductility at room temperature and below. These alloys deformed by twinning at room temperature when subjected to slow loading rates. It appeared that the low-temperature ductility resulted at least in part from the relaxation of stresses by twinning in a system where slip is difficult. The reason for enhanced twinning behavior in some bee solid-solution alloys is unknown. There have been suggestions18,19 that, as in fee alloys, the

Jan 1, 1965

By Rodney P. Smith

The rate of motion of the boundary between a single-phase a-iron region and a two phase a-iron plus ?-iron, or a-iron plus cementite region has been measured on decarburization at several temperatures between 500" and 865°C. These data, together with data for the carbon content of a-iron at the boundary, yield the diffusivity of carbon in a-iron. The activation energy for carbon diffusion is 19.8 kcal per mole for the temperature range —50° to 150°C and increases to an average value of 23.0 kcaL per mole for the temperature range 727" to 865°C. AS part of an investigation of the diffusivity of carbon in iron using a steady-state method,' the diffusivity of carbon in a-iron was determined at the temperatures 802" and 851°C. The diffusion constant thus obtained was larger, by nearly a factor of two, than that predicted from the combined results of stanley2 and of Wert.3 It seemed desirable, therefore, to continue the investigation. Since the temperature range in which the steady-state method can be conveniently used is limited, we have chosen a decarburization method, based on the laws of diffusion in metal accompanied by a phase change.4,5 If the initial carbon content of the Fe-C alloy is such that two phases coexist at the decar-burizing temperature* and decarburization is car- ried out such that the surface is maintained at substantially zero wt pct. C, the carbon distribution after a time, t, will be as shown in Fig. 1. The boundary between the single-phase and two-phase regions moves from y = 0 to y = x in the time, t, where x is proportional4 to tl". If the initial carbon (content of the sample is Ci, and CB is

Jan 1, 1962

Since I have had the pleasure of watching the development of this process very closely, I feel that I ought to say a few words on the subject, although I cannot add much to what Mr. Roe has already said. I wish, however, to bear witness to the hard work, persistence and skill which have been exercised during the past two years, and which have so well deserved the success attained. Those of us who remember the history of the past efforts in this line, such as the rotary puddlers, in which also some of us had a part, can easily appreciate the problems involved, and may well be skeptical as to the outcome. Such, at least, was my frame of mind when the process first came under my notice. Now, after having seen every heat, but three, of the many made, it really seems to me that a process and plant for the mechanical puddling of iron has at last been developed which is practical, economical and successful. Of course I do not mean by this that either the process or the machines are developed to their highest point, technically or economically, but that, in my opinion, these goals are in plain view, and that the difficulties which remain are such as will be overcome by developing the skill of the operator through practice ;

Jan 1, 1903

By Robert M. Yonco, Irving Johnson, Martin G. Chasanov

The thermodynamics of the cadmium-rich portion of the Pu-Cd system has been studied with a high-temperature galvanic-cell method. The partial phase diagram of the Pu-Cd system was determined. The existence of the intermediate phases PuCd11 (cubic BaHg11 structure, ao= 9.282) and PuCd6 (cubic, CeCd6 structure, a, = 15.59) was established. The existence of at least one other intermediate phase richer in plutonium was indicated. PuCd11 was found to peritectically decompose into PuCd6 and liquid at 406" * 2°C. The solubility of plutonium in liquid cadmium may be represented by the equations: (355' to 399°C) log (at. pct Pu) = 6.223 -4282T-1 (399° to 632°C) log (al. pct Pu) - 5.148 - 5277T-1 > 1.156 x 106 T-2 The free energy of formation values (kcal per mole) of the two intermetallic phases are given by the equations: (PuCd11), ?Gf= -45.9 + 35.7 x 10-3 T (PuCd6), ?Gf0- -39.27 + 25.86 X 10-3T The excess free energy (kcal per mole) of plutonium in liquid cadmium may be represented by the equation: -(-16.72 * 29.54 NPu) 10-3T in which Npu and Ned are the atom fractions of plutonium and cadmium. The thermodyanamics of the U- Cd and Pu-Cd systems are compared. THERMODYNAMIC information on systems of the actinide metals with low-melting metals, such as zinc and cadmium, is useful in the design of pyro-metallurgical processes for the purification of nuclear reactor fuels. The thermodynamics of the Pu-Zn,1 Th-Zn.2,3 U-Zn,4-5 and U-Cd6 systems have been reported. The present report on the Pu-Cd system concerns the liquidus composition in the cadmium-rich region, the characterization of the two most cadmium-rich intermetallic phases, and the thermodynamic properties of these intermetallic phases and dilute liquid solutions of plutonium in cadmium. EXPERIMENTAL Phase Studies. The liquidus composition was determined by analysis of filtered samples of the liquid phase withdrawn at a series of temperatures. The apparatus and procedure were identical to that used in the previous study of the Pu-Zn system.' Briefly. a sample of the melt was withdrawn into a tantalum tube fitted with a porous tantalum filter (30-µ pore). the entire sample dissolved in hydrochloric acid (to avoid errors due to segregation

Jan 1, 1965

By F. F. Sharpless

ON Saturday evening, Sept. 9, a small party of Institute members, their wives and friends, left New York to attend the Fall Meeting of the Institute at San Francisco. In this party there were: President and Mrs. Arthur S. Dwight; Mr. and Mrs. George D. Barron; Mr. and Mrs. H. J. Stehli; N. S. Spencer and Miss Spencer; the Secretary and Mrs. F. F. Sharpless. They were joined at Chicago by E. F. Eurich, and by Mr. and Mrs. R. L. Baldwin and daughter. Our party was met at Chicago by Mr. and Mrs. L. V. Rice, Mr. and Mrs. A. D. Terrell and W. F. Boericke, who constituted themselves an impromptu entertainment committee and proceeded to carry out a delightful little program. We were taken to the Lake Shore drive, where a stiff wind off the lake refreshed us after a sultry day on the train, and on our return to the city saw Chicago illuminated with all its brilliance of electricity. We were entertained at dinner at the Drake Hotel. In spite of being two hours late getting into Omaha, we were right on the dot at Denver on Tuesday morn-ing. Horace F. Lunt came to the hotel soon after breakfast, and told us that a trip to the mountains had been planned. Having learned the number in the party, he began to gather up his automobiles for a 10 o'clock start.

Jan 10, 1922

By William B. Plank

FOR the third consecutive year, I have collected the data on enrolment and employment of graduates from the schools in. the United States and Canada that grant degrees in mineral technology. The data were collected in the same way as formerly; namely, by questionnaire, dated Jan. 5, 1935, and are therefore comparable with the figures reported for former years. This year, along with the names of the 48 schools in the United States and the six in Canada, are listed the courses offered and the degrees granted by each, school, together with the names of the professors in charge. The names and addresses of the four schools in Mexico are also given. The list is on pages 450-1, which should he valued as a directory by those interested in mineral technology education. So far as is known, this is the most complete and up-to-date list that has ever been published.

Jan 1, 1935