Search Documents

By V. Steve Reed, Ed L. Reed

The in situ leach mining process generates a waste stream that is high in sulfates, total dissolved solids, and radium 226. During the mining phase, the volume of the waste stream is relatively low and consists primarily of the bleed stream. During the restoration phase, larger volumes of waste water are generated. These waste streams require environrnentally sound disposal. The low net evaporation rate in the Coastal Bend area precludes pond evaporation as a feasible disposal alternative. Reverse osmosis is a practical method of reducing the volume of the waste water handled, but the concentrated waste stream from the reverse osmosis unit must be disposed properly. Deep well injection into highly saline reservoirs is considered a sound method of disposing of the liquid waste generated by in situ mining in the Gulf Coast uranium district. Thirteen injection wells have been permitted to serve the disposal needs of the leach mining industry in Texas. Of these 13, 11 have actually been drilled. Seven applications are pending. The injection zones for the permitted wells range from depths of 3050 to 6200 feet. Pressure limitations imposed on these wells range from 500 psi to 1350 psi. The following criteria are used to determine the desirability of a disposal well site: 1. A minimal number of nearby, improperly plugged borings which penetrate the disposal zone; 2. Minimal crustal disturbance; 3. Sufficient salinity of the water contained in the disposal zone; 4. Protection of oil and gas producing zones; and 5. Sand of sufficient permeability and areal extent to handle the desired volume without fracturing the reservoir. 1. Improperly plugged borings: During the early part of the century, oil wells, gas wells and test holes were drilled using cable tool equipment, often with a minimum amount of surface casing. Production casing, when it was set, was often partly removed when the holes were abandoned. Thus, wells drilled prior to 1940 frequently have less than 100 feet of surface casing and either no production casing or the upper part of the production casing removed. Additionally, these holes are often plugged only with mud. The close proximity of these holes to an injection well location are a concern in that they can provide an avenue for injection-depth fluids to migrate up the bore hole and jeopardize shallower fresh water reservoirs. Usually, where there are more than 6 or 8 poorly plugged borings in a 2 1/2 mile radius of the well site, it is preferable to examine deeper zones for disposal well potential. The deeper zones are especially attractive where the borings are not in a cluster, which renders monitoring more difficult. Often, even the deeper disposal zones are penetrated by a few improperly plugged borings. When this condition arises, the potential for leakage through the borings can be addressed in the following ways. a. Demonstration that the static head in the boring is higher than the anticipated increase in bottom hole pressure generated at the boring by the disposal well. A 100 psi differential between these two pressures is recommended. The calculated increased pressure at a boring caused by injection should be refined using annual bottom hole pressure measurements in the disposal well. Figure 1 illustrates an injection pressure map which can be overlain on the oil well map to determine the anticipated increase in pressure expected at each oil, gas or abandoned hole. b. Shallow ground water monitoring. A shallow monitor well is drilled next to the boring and both pressure and quality measurements are made periodically in the shallow well. c. Disposal zone monitoring. Recently there has been a tendency for regulators to require disposal depth monitor wells instead of shallow well monitoring. We consider disposal depth monitoring to be a less effective method of monitoring because it provides only indirect evidence of potential problems. Assumptions have to be made for the unplugged borings, such as mud weight, that are not addressed by the disposal zone monitoring program. There is little improvement with this system to that discussed in "a" above. A shallow zone monitoring program, however, yields direct evidence of a developing problem with an unplugged boring. Leakage by the boring will be detected quickly by an abnormal increase in pressure in the shallow well. Quality monitoring will detect upward migration of poor quality fluids. The pressure data provide an early warning of impending leakage; the quality monitoring will detect actual fluid migration.

Jan 1, 1980

Jan 1, 1880

By R. C. Corson

Modern microprocessor systems make it possible to use several variables to anticipate changes in the process and to react with responses before upsets can be magnified by the process or by control action. Through tighter control, "insurance" can be eliminated from process set points without affecting product quality. In actual operation with a traveling grate furnace this control philosophy has produced savings of up to 20% in fuel consumption and 8% in fan power usage while producing a more consistent quality product.

Jan 1, 1984

By J. Armanet

THREE MINING colleges are maintained in France; the École Nationale Supérieure des Mines, of Paris; École Nationale Supérieure des Mines, of Saint Etienne; and the École Supérieure de la Metallurgie et des Mines at Nancy. Besides graduates of these schools, a few graduates of the École Centrale des Arts et MIanufactures and of the École Polytechnique are employed as ]nine managers or engineers; however, most of the latter have taken a graduate course at one of the mining schools.

Jan 1, 1939

By Richard H. Jahns

Gem materials, comprising those minerals and closely allied natural substances used for personal adornment, for the fashioning of ornamental objects, or for other decorative purposes, have been valued in human commerce for thousands of years. Amber, jet, natural glasses, and at least 15 mineral species were sought and used by primitive man, and most of the materials in common use today were known well before the time of Christ. Their variety is remarkably great, and the traceable relationships among their respective sources, modes of occurrence, properties, and histories of production, preparation, and valuation are extremely complex. Their uses have been affected by numerous shifts in fashion, and from time to time by superstition, by decrees of church and state, by personal interpretations of religious significance, and by various presumptions concerning medicinal value and influence on human behavior (Ball, 1935, 1950; Kunz, 1913; Pogue, 1915, Whitlock, 1946). Thanks to their durability, portability, and relative scarcity, some gem stones have been employed as media of exchange, and the investment value of the more precious stones has long been recognized and exploited, especially in Asiatic and European countries. Demands for gem materials have stimulated trade among various peoples for centuries, and they also were responsible for much early geographic exploration. During more recent times they have prompted numerous geological studies and a considerable amount of research on the growth and properties of crystals. Apart from decorative uses, some naturally occurring gem materials also are employed directly in numerous fields of industry. Substances that are manufactured for gem or industrial uses are termed synthetic gem materials; most of these correspond in composition and crystal structure to certain minerals found in nature. Imitation materials are those whose use is based upon their resemblance to substances of different composition and greater intrinsic value. Gem stone is a designation commonly restricted to those materials suitable for personal adornment, and the complementary term ornamental stone is applied to the remaining materials not used industrially. This distinction is arbitrary and somewhat inconsistent, owing to numerous geographic differences and historical shifts in end uses. Further, there is a complete gradation between the category of ornamental stones and that of dimension stone. Substances that lose their identity in use are excluded from the gem category; thus a transparent crystal of beryl would not be classified as a gem stone if it were processed as a source of beryllium metal. The adjectives precious and semiprecious have been employed as a means for distinguishing different gem materials on the basis of recognized value. Diamond, emerald, ruby, and sapphire consistently have been regarded as precious stones, and in cut form they commonly are referred to as the noble gems. Opal, pearl, turquoise, and chrysoberyl also have been classed as precious at various times. In recent years, however, it has been increasingly recognized that no satisfactory distinction can be based upon assessed value or any group of specific properties, and now all gem stones normally are referred to as precious. Indeed, the tendency is to extend this term to include many of the so-called ornamental stones, and the designation semi- precious has been essentially discontinued. Unlike most mineral commodities of economic value, gem materials are little altered in processing for end uses. Some stones are used in essentially their natural form, and most are reshaped and polished without significant changes in their fundamental properties. Thus the preparation of gem and ornamental stones is intended chiefly to emphasize or enhance

Jan 1, 1975

By George Hunt

THE first practical treatment of wood to prevent decay was devised early in the 19th century. At that time the oaken navy of England, when . the nation was fighting for its very existence, seemed doomed to annihilation by the swift ravages of decay. The acute situation inspired a desperate search for preventive measures and resulted in the development of the Burnett, Bethel and Kyan processes for impregnating wood with zinc chloride, coal-tar creosote and mercuric chloride, respectively. In the century that has elapsed, their use has spread throughout the world and the three original preservatives are used today in enormous quantities. Meanwhile, improved processes have been developed, new preservatives discovered, and the practice of impregnating wood to make it last longer has attained a position of major importance in the field of structural materials. USE OF PRESERVATIVES BY- THE RAILROADS In the application of wood preservatives in the United States the railroads have been the leaders for the past 50 years or more.. Having found, that decay is the chief cause of the early destruction of wood and that preservative treatment is the remedy, they have treated their ties and timber in increasing amounts(1) ?-in 1925 about 220,000,000 cubic feet. By preservative treatment the Santa Fe Railroad saves annually 1,500,000 ties in its 18,000 miles of track, and many other railroads effect similar savings. (2) In like manner the life of wooden bridges and trestles,(3) poles, marine piling, water tanks and other wooden railroad structures has been greatly increased, reducing the amount of timber required annually to maintain them.(5),(7)

Jan 2, 1927

By George Hunt

THE first practical treatment of wood to prevent decay was devised early in the 19th century. At that time the oaken navy of England, when the nation was fighting for its very existence, seemed doomed to annihilation by the swift ravages of decay. The acute situation inspired a desperate search for preventive measures and resulted in the development of the Burnett, Bethel and Kyan processes for impregnating wood with zinc chloride, coal-tar creosote and mercuric chloride, respectively. In the century that has elapsed, their use has spread throughout the world and the three original preservatives are used today in enormous quantities. Meanwhile, improved processes have been developed, new preservatives discovered, and the practice of impregnating wood to make it last longer has attained a position of major importance in the field of structural materials. USE OF PRESERVATIVES BY THE RAILROADS In the application of wood preservatives in the United States the railroads have been the leaders for the past 50 years or more. Having found that decay is the chief cause of the early destruction of wood and that preservative treatment is the remedy, they have treated their ties and timber in increasing amounts(1)?-in 1925 about 220;000,000 cubic feet. By preservative treatment the Santa Fe Railroad saves annually 1,500,000 ties in its 18,000 miles of track, and many other railroads effect similar savings. (2) In like manner the life of wooden bridges and trestles,(3) poles, marine piling, water tanks and other wooden railroad structures has been greatly increased, reducing the amount of timber required annually to maintain them.(5),(7)

Jan 1, 1927

THE first mention of the mining and use of coal in the Pittsburgh district refers to the mine under Duquesne Heights that furnished coal for the garrison at the fort at Pittsburgh in 1760. Coal had been dug and used as fuel just outside of Brownsville, Fayette county, in 1759, but this was not a regular mine as the opening was in an outcropping. Maps of Ohio in 1770 showed "Cole Mines" at various points. The Penns purchased all the coal south of Kittanning in southwestern Pennsylvania from the Chiefs of the Six Nations for a reported price of $10,000. During the Revolution, coal from Herron Hill, Minersville, and Coal Hill, all within the present city limits, was used in Pittsburgh. There is today one custom pit opened in Coal Hill (Duquesne Heights). The first steam engine was set up in Pittsburgh in 1794 and used coal as fuel. The first mine in the Youghiogheny gas district was opened in 1796. In 1803, the first shipment of coal by water was made from Pittsburgh down the Ohio river and landed at Philadelphia, where it sold for approximately $9.50 per ton. The mines along the Monongahela were naturally the first to be opened. With the completion of locks and dams in 1844, permitting slack-water navigation, the industry began to thrive. The No. 8 field of Ohio and the Fairmont region of northern West Virginia were opened in the period 1840 to 1855. From that time on there has been a continuous development of the coal resources of this district, until at present-productive capacity is enough to supply 30 per cent. of the country's needs of bituminous coal. The original method of working the Pittsburgh seam was to drive under cover at some .easily accessible point on the outcrop with a single entry, usually 1 1/2 yd. wide. Rooms or gangways were turned to the

Jan 10, 1926

The first mention of the mining and use of coal in the Pittsburgh district refers to the mine under Duquesne Heights that furnished coal for the garrison at the fort at Pittsburgh in 1760. Coal had been dug and used as fuel just outside of Brownsville, Fayette county, in 1759, but this was not a regular mine as the opening was in an outcropping. Maps of Ohio in 1770 showed "Cole Mines" at various points. The Penns purchased all the coal south of Kittanning in southwestern Pennsylvania from the Chiefs of the Six Nations for a reported price of $10,000. During the Revolution, coal from Herron Hill, Mincrsville, and Coal Hill, all within the present city limits, was used in Pittsburgh. There is today one custom pit opened in Coal Hill (Duquesne Heights). The first steam engine was set up in Pittsburgh in 1794 and used coal as fuel. The first mine in the Youghiogheny gas district was opened in 1796. In 1803, the first shipment of coal by water was made from Pittsburgh down the Ohio river and landed at Philadelphia, where it sold for approximately $9.50 per ton. The mines along the Monongahela were naturally the first to be opened. With the completion of locks and dams in 1844, permitting slack-water navigation, the industry began to thrive. The No. 8 field of Ohio and the Fairmont region of northern West Virginia were opened in the period 1840 to 1855. From that time on there has been a continuous development of the coal rcsources of this district, until at present productive capacity is enough to supply 30 per cent. of the country's needs of bituminous coal. The original method of working the Pittsburgh seam was to drive under cover at some easily accessible point on the outcrop with a single entry, usually 1½ yd. wide. Rooms or gangways were turned to the right and left from this entry and ventilation was usually poor and inade-

Jan 1, 1927

By H. G. Botset

ANY information that will increase the accuracy of our knowledge of the conditions prevailing in petroleum reservoirs should be of direct value in the determination of the proper operating technique as well as in the estimation of reserves and of ultimate production. The obvious method of obtaining this information is by studying a sample of the reservoir rock and its contents. In any such study, the problem of primary importance and maximum difficulty is that of getting the core to the surface in such a manner that its original fluid content is undis-turbed, which has so far proved to be an impossible task. Though it might be rash to say this will never be done, it is certainly safe to assume that a method for the recovery of a core at the surface in its undisturbed original state may not be developed in the immediate future, and certainly will not be forthcoming without a great deal of costly experimentation. Therefore any information that may be obtained that will help to correlate the state of a core (its fluid saturation) at the surface with its condition at the time it was drilled should be of value to the petroleum industry. The experiments described in this paper were undertaken with the purpose of determining, if possible, any relationship that might exist between the saturation of a core at the surface and its original fluid content. No consideration has been given to the question of contamina-tion by penetration of drilling water, since this problem has been exten-sively studied by other investigators. 1-3 Furthermore, it was regarded as being outside the scope of the present experiments, which were con-cerned only with the effect of pressure reduction upon the liquid content of cores. In an experimental study of this sort involving a large number of variables, accurate control of all factors is very important. The essen-tial and obvious procedure is to vary systematically one factor or condi-tion while keeping all the others constant, which necessarily involves a rather protracted and sometimes tedious experimental program.

Jan 1, 1939

By E. Ray Webb

A interest to geologists and to mining and petroleum engineers is a laboratory method for determining the dip and strike of sub- surface structures, as well as the direction of fault planes traversing them. The information is derived by making use of the magnetic properties of borehole cores which must show visible representations of bedding or fault planes. Complete knowledge of these factors aids greatly in the successful exploitation of both ore and petroleum deposits.

Jan 1, 1940

By M. E. Wadsworth, D. R. Wadia

The rate of reaction of cuprite was measured in a series of sulphuric acid solutions, from which oxygen had been excluded, at various concentrations and temperatures. The overall reaction CuzO + H2S04 + Cu " + CuO + H20 + So4' may be explained quantitatively by two simultaneous rate reactions involving not only H+ but also the hydrolytic adsorption of H2SO4. The results indicate the importance of considering surface mass balance relationships associated with heterogeneous surface reactions. T EACHING has long been an important method for the recovery of metals from certain minerals. Many processes have assumed minor importance in modern practice but such operations as the recovery of uranium and present interest in high pressure-high temperature solution of sulphides' ' well illustrate the importance of leaching as a unit operation. Little quantitative information is available in a form sufficient to determine the mechanism of solution at the solid-aqueous solution interface for given systems. For this reason, it is important that fundamental studies of leaching processes be conducted so that parameters associated with such surface reactions may be understood and correlated. Cuprite was chosen for this study as a result of a recent investigation carried out at the University of Utah on ores of the Ray and Chino Mines Divs. of the Kennecott Copper Corp. These sulphide deposits contain sufficient oxidized minerals, such as cuprite, malachite, and azurite, so that recovery of metal values contained in the oxidized fraction is of primary interest. Of these oxides, cuprite (Cu,O) is the most interesting, since it dissolves in sulphuric acid by an oxidation reduction couple resulting in the formation of 50 pct metallic Cu and 50 pct cup-

Jan 1, 1956

By M. Muskat, H. G. Botset

Any information that will increase the accuracy of our knowledge of the conditions prevailing in petroleum reservoirs should be of direct value in the determination of the proper operating technique as well as in the estimation of reserves and of ultimate production. The obvious method of obtaining this information is by studying a sample of the reservoir rock and its contents. In any such study, the problem of primary importance and maximum difficulty is that of getting the core to the surface in such a manner that its original fluid content is undisturbed, which has so far proved to be an impossible task. Though it might be rash to say this will never be done, it is certainly safe to assume that a, method for the recovery of a core at the surface in its undisturbed original state may not be developed in the immediate future, and certainly will not be forthcoming without a great deal of costly experimentation. Therefore any information that may be obtained that will help to correlate the state of a core (its fluid saturation) at the surface with its condition at the time it was drilled should be of value to the petroleum industry. The experiments described in this paper were undertaken with the purpose of determining, if possible, any relationship that might exist between the saturation of a core at the surface and its original fluid content. No consideration has been given to the question of contamination by penetration of drilling water, since this problem has been extensively studied by other investigators.1-3 Furthermore, it was regarded as outside the scope of these experiments, which were concerned only with the effect of pressure reduction upon the liquid content of cores. In an experimental study of this sort involving a large number of variables, accurate control of all factors is very important. The essential and obvious procedure is to vary systematically one factor or condition while keeping all the others constant, which necessarily involves a rather protracted and sometimes tedious experimental program. The procedure adopted was essentially very simple, and consisted merely in filling a given core with fluid (gas and oil, gas and water, or

Jan 1, 1939

By M. Muskat, H. G. Botset

Any information that will increase the accuracy of our knowledge of the conditions prevailing in petroleum reservoirs should be of direct value in the determination of the proper operating technique as well as in the estimation of reserves and of ultimate production. The obvious method of obtaining this information is by studying a sample of the reservoir rock and its contents. In any such study, the problem of primary importance and maximum difficulty is that of getting the core to the surface in such a manner that its original fluid content is undisturbed, which has so far proved to be an impossible task. Though it might be rash to say this will never be done, it is certainly safe to assume that a, method for the recovery of a core at the surface in its undisturbed original state may not be developed in the immediate future, and certainly will not be forthcoming without a great deal of costly experimentation. Therefore any information that may be obtained that will help to correlate the state of a core (its fluid saturation) at the surface with its condition at the time it was drilled should be of value to the petroleum industry. The experiments described in this paper were undertaken with the purpose of determining, if possible, any relationship that might exist between the saturation of a core at the surface and its original fluid content. No consideration has been given to the question of contamination by penetration of drilling water, since this problem has been extensively studied by other investigators.1-3 Furthermore, it was regarded as outside the scope of these experiments, which were concerned only with the effect of pressure reduction upon the liquid content of cores. In an experimental study of this sort involving a large number of variables, accurate control of all factors is very important. The essential and obvious procedure is to vary systematically one factor or condition while keeping all the others constant, which necessarily involves a rather protracted and sometimes tedious experimental program. The procedure adopted was essentially very simple, and consisted merely in filling a given core with fluid (gas and oil, gas and water, or

Jan 1, 1939

By Hans Lundberg, Basil T. Wilson, H. Steuart Scott

FOR the benefit of those readers who may not be in close touch with present practices in the geophysical prospecting for ore, brief reference will fiat be made to the advantages and shortcomings of the methods to be discussed. Magnetic and electric methods are generally accepted as the most useful for ore prospecting. By magnetic methods, magnetic intensities that are not normal may be recorded and outlined. From these can he located concentrations of such highly magnetic minerals as magnetite or pyrrhotite, which sometimes occur in such large masses that they are of economic value in themselves. More often. however, these magnetic min¬erals are associated with others, such as copper, zinc, lead, gold, and silver, which, if existing in sufficient concentration and quantity, may constitute valuable ore bodies. It is therefore only when pyrrhotite and magnetite are present in these bodies that the magnetic method can be used to indicate their presence.

Jan 1, 1945

By CHARLES HOPPER

In preparing the Steep Rock Lake iron ore body for mining, it was necessary to drain Steep Rock Lake. Using diamond drills, a cut 1800 ft long, 100 ft wide, and maximum depth of 95 ft amounting to 300,000 cu yd of material, was excavated in Greenstone to provide a drainage channel. This was done under the general contractor C. A. Pitts, of Toronto, who in turn employed a diamond drill contractor, Boyles Bros., to do the drilling. The method of excavation was selected be- cause a clean square cut and grade could be maintained in the bottom of the channel. Bootlegged holes would have left blocks of rock in the corners which would have created a situation which would have become progressively worse as the open cut advanced from one side of the ridge to the other.

Jan 1, 1949

By B. Habermann

Artificially consolidated sand models, representing one-quarter of a five-spot, have been developed and used to study factors aflecting misciblt. displacrmenr. Sweep efficiency at breakthrough, size of the mixing zone between two miscible liquids and per cent area contacted by drive after breakthrough were determined tor the high mobility ratios encountered in actual resvrvoirs. Quantitative relationships between the degree of viscous fingering and mobility ratio were obtained by measuring the length of the fluid interface. Scaled miscible-slug experiments, supported by field evidence reported in the literature, have shown that when the slug is followed by dry gas the process is less efficient than expected. In addition to low areal sweep efficiencies encountered for high mobility ratio displacements, the effectiveness of a miscible slug is greatly reduced. This is caused by an accelerated growth of the mixing zone between the driving and the displacing fluids. INTRODUCTION Considerable interest in miscible displacement as a secondary recovery process has been shown by the oil industry in recent years. In addition to extensive laboratory investigations, numerous field operations have been initiated so that 39 miscible displacement projects had been reported' in the United States by early 1959. By far the most popular approach in these projects is the use of an LPG slug followed by dry gas. Laboratory tests have indicated that with a small miscible slug, amounting to several per cent of the hydrocarbon pore volume, practically 100 per cent recovery of the oil in place can be achieved and that all of the slug material can be recovered by a subsequellt gas drive. However, these experiments were conducted on small-diameter long cores that can be considered as essentially uni-dimensional reservoirs that do not represent actual field conditions. It soon became apparent that the inherently adverse mobility ratios existing in the reservoir cannot be ignored in any miscible displacement field project. When a less viscous fiuid such as an LPG slug drives a more viscous reservoir oil, fingers develop that reduce the areal sweep efficiency. The slze of the miscible slug to be used is a subject of some controversy. It has been proposed that the size of siug needed be calculated by setting lengths of the mixing zone proportional to the square root of the distance traveled. This proposal is based on experimental evidence' and theoretical considerations"' in which fingering was not a factor. A prerequisite for successful application of the miscible displacement process to field operations is a better understanding of the following factors. L What is the effect of mobility ratio on the rate of deterioration of a miscible slug? 2. How large a slug should be used for given reservoir conditions? 3. What is the sweep efficiency? The purpose of this investigation was to provide some additional laboratory data that should help to answer these questions. More specifically, it was intended to study more quantitatively the effect of viscous fiinger-ing, mobility ratio and slug size on the efficiency of this relatively new secondary recovery process by means of experiments on thin, horizontal, porous medium models.

By C. E. Barnett, G. R. Durland

LUMINESCENT materials have been used in an increasing variety of ways in recent years. Such uses range from the screens on which the picture or image is presented in television and other cathode ray tubes to fluorescent lamps, fluorescent effects in decorative, theatrical, and display lighting, and the many applications of phosphorescence in paints, textiles, paper, and plastics. During the war the screens for a radar set or the "night-seeing" devices were not fundamentally different from those in other cathode ray tubes, but nevertheless they presented special problems for the phosphor manufacturer. It was essential that the "pips" on a radar screen continue to glow after the exciting beam had swept on, but this afterglow would be ruinous to a television screen. In the image tube used for seeing at night with infrared instead of visible light, electrons emitted by an infrared-sensitive receiving surface were amplified and converted to visible light after striking a fluorescent screen. The small size of the screen caused special problems in reducing the grain size of the phosphor to obtain adequate resolution. Other devices used phosphor surfaces which could be stimulated directly by infrared radiation to emit visible light. Energy was stored in the phosphors by prior excitation with short-wave-length radiation, and the stored energy released on subsequent exposure to infrared radiation. Maps, navigational charts, bombing manuals, and computers of various sorts were printed on fluorescent paper or lettered with fluorescent inks. Fluorescent markings excited by small ultraviolet lamps were used on airplane instrument dials. A large amount of research was done to determine the best color for the emitted light and other properties for the fluorescent materials, and on the best methods for their fabrication into the items listed above. Phosphorescent materials found wide use during blackout restrictions to mark safe passageways, to delineate traffic hazards, to identify packages, and to mark tools and other items of equipment.

Jan 1, 1948

By E. P. Mathewson

THE OLD Pueblo smelter is being dismantled after 43 years of continuous operation, from 1878 to 1921. It was built by Mather and Geist, on a bluff overlooking the Arkansas River just below the, city of Pueblo. At the time of its construction Pueblo was considered a most favorably situated town for a custom smelter. Coal, coke, fuel, limestone, iron ore, lead, silver, and, gold ores were plentiful. It was a "downhill pull" from all directions to Pueblo. Labor, both common and skilled, was plentiful and efficient. Leadville was in bonanza and there were not sufficient furnaces in Colorado to handle the ore offered. The plant prospered from the start. It soon required more capital; so the owners; with the assistance of Thomas Nickerson of Boston, at that time prominent in the affairs of the A., T. & S. F. railway, formed the Pueblo Smelting & Refining Co. About this time, also, very heavy shipments of rich silver ore from New Mexico began to come in. Agencies were established for the purchase of ores in the most important mining camps in the country from Kingman, Ariz., to Butte, Mont. Highly siliceous silver-bearing ores from Butte were shipped to Pueblo in train loads. This was used chiefly in the concentration of leady mattes. RECOLLECTIONS OF MR. GEIST, FOUNDER OF PLANT Mr. Geist is living in Guadalajara and has sent the following brief letter: "Early in 1878 the firm of Mather & Geist, which had been operating in Utah and had then closed their smelter there, after diligent search for a new location selected Pueblo. We erected the first smelter in the valley, blowing in the first furnace in 1878. Mather & Geist carried on until January, 1882, when they transferred all their business to the Pueblo Smelting & Refining Co., which had been organized in December, 1881. Full details of this transfer are given in the enclosed Report, which was issued early in 1882, for the purpose of interesting more capital, in which we succeeded admirably. "I personally did all the work of manager and super-intendent, some job in these days. My technical quali-fications were that I was a member of the class of 1866, Yale Sheffield Scientific. I was born in 1848, so was the youngest member of the class.

Jan 11, 1923

By W. J. Parton

THE efficient recovery and preparation of small sizes of anthracite called No. 4 Buckwheat (3/3 2 by 1/3 2 in.) and No. 5 Buckwheat (1/3 2 in. by 0), present a difficult problem to the anthracite operators. In many instances preparation of these sizes, particularly No. 5 anthracite, is extremely inefficient. In many of the older preparation plants, inadequate facilities, and often none at all, were provided as an integral part of the plant for cleaning this fine anthracite. Consequently, much of the material smaller than s, 32 in. was discarded. As the demand for these sizes increased, facilities for preparing the fine sizes were often crowded into existing structures with consequent sacrifices of capacities and efficiency. In addition to this condition, the methods of preparing the finest sizes are being developed in an attempt to improve their efficiencies. Because the demand for small sizes of anthracite still is increasing, many operators would benefit by investigating and improving the cleaning equipment employed on these sizes.

Jan 1, 1949