Search Documents

By N. L. Ananthanarayanan, J. F. Libsch

A LITERATURE survey1-' of sintering metal pow-A ders and powder compacts indicates that studies have so far been confined primarily to the latter stages of sintering in relatively coarse powders. Presumably this is due to the difficult techniques associated with studies of the early stages of sintering. Recent experimental and theoretical investigationsL-" on the preparation and the magnetic properties of ultrafine ferromagnetic powders suggest the possi- bility of following the sintering process from a very much earlier stage than has previously been considered. It is now well-known that ferromagnetic powder particles which are below a critical size behave as single domains and exhibit permanent magnet qualities characterized by a very high coercive force. When the same particles are fully sintered, the coercive force decreases to very low values corresponding to those of the solid metal. Thus the coercive force appears as a sensitive parameter which may be measured to study the early stages of sintering. To determine the feasibility of this technique, experi-

Jan 1, 1954

By Henry M. Howe

The transformation which steel undergoes in slow cooling, from the condition of austenite whelk above the transformation rage into that of pearlite plus either ferrite or cementite below that range, is subject to great lag. This transformation is essentially the pearlitizing of the austenite. Indeed the hardenillg of steel is due to this lag, which is made so great by extremely rapid cooling that a very large part of the transformation itself is restrained, so that the rapid cooling catches the metal in an only partly transformed state, that of martensite, and under favorable contditions even in an almost wholly untransformed state, as in the cases of Maurer's austenitic manganese steel. Hadfield's austemtic. manganese steel, 25 per cent. nickel steel, and other anstenitic alloy steels, arc austenitic even after slow cooling. It has long been known that this lag increases (1) with the rapidity of cooling, (2) with the presence of certain retarding elements, notably manganese and nickel, and (3) with the temperature from which cooling starts. The present inquiry touches the last of these influences, but incidentally it throws light on the first also. This influence of higher heating ill increasing lag manifests itself in different ways which, though they may at first seem unrelated, are in fact hut different aspects of one and the same thing. Thus, among heatings to different high temperatures, all of them above the transformation range: the higher the temperature to which the steel is heated (1) the lower is the temperature at which the transformation occurs in cooling slowly down, (2) the shorter is the time occupied in the actual cooling from above the transformation range to the room Temperature under given external conditions, Whether of slow or

Jan 1, 1914

By Henry Howe

(New York Meeting, February, 1913.) THE transformation which steel undergoes in glow cooling, from the condition of austenite when above the transformation range into that of pearlite plus either ferrite or cementite below that range, is subject to great lag. This transformation is essentially the pearlitizing of the austenite. Indeed the hardening of steel is due to this lag, which is made so great by extremely rapid cooling that a very large part of the transformation itself is restrained, so that the rapid cooling catches the metal in an only partly transformed state, that of martensite, and under favorable conditions even in an almost wholly untransformed state, as in the cases of Maurer's austenitic manganese steel. Hadfield's austenitic manganese steel, 25 per cent. nickel steel, and other austenitic alloy steels, are austenitic even after slow cooling. It has long been known that this- lag increases (1) with the rapidity of cooling, (2) with the presence of certain retarding elements, notably manganese and nickel, and (3) with the temperature from which cooling starts. The present inquiry touches the last. of these influences, but incidentally it throws light on the first also. This influence of higher heating in increasing lag manifests itself in different ways which, though they may at first seem unrelated, are in fact but different, aspects of one and the same thing. Thus, among heatings to different high temperatures, all of them above the transformation range, the higher the temperature to which the steel is heated (1) the lower is the temperature it which the transformation occurs in cooling slowly down, (2) the shorter is the time occupied in the actual cooling from above the transformation range to the room temperature under given external conditions, whether of slow or

Jan 3, 1913

By Louis Ware

BEFORE the war we often heard the term "Big Business." And there were complaints of the ills and abuses attributed to bigness in business. Although there were examples where the small businessmen spoke for their rights and sought protection from the bigger ones, it has only been in recent war years that a tendency has developed definitely to divide the business of our nation into the big and the small. In some cases, those with an eye to the political value of the vastly greater number of small businessmen of the country have fomented this division by hurrying to the protection of these more numerous voters, and intentionally or not have emphasized in their writings and verbal attacks any and all differences of these interests that could either be found or fabricated to, suit the occasion. It has become another example of breaking the people into classes and thus setting up the basis for the claims of one class against another, and the subsequent demand for legislation and Governmental aid. The terms "big" and "small" are purely relative. One businessman, employing a hundred men, told me recently he did not know which adjective would be more appropriately applied to his operation. He did not know whether he should join the small operators' group that had been organized, or should consider himself big. He said that his present plant seemed big to him when he looked back to its humble beginning many years ago with a couple of men in two rooms. Yet, when compared with many of his competitors who employ thousands, his was small. He did add, however, that he probably became big one day a few years ago when the union moved in and organized his employees.

Jan 1, 1945

By G. L. Oldright

Nearly all of the present schemes for treating complex (i. e. lead-silver-zinc-copper) ores are based on the idea that lead holds, and will hold for some time, the strongest economic place from the viewpoint of supply and demand of all the non-ferrous metals. Copper, it is thought, will come back to its own when European affairs are stabilized, although at that time competition from Chile, Peru, and Katanga, in particular, will be more severe than in pre-war days. The future for silver and for zinc is uncertain. New uses are developing for zinc, and the market has remained better than many expected, but the stabilization of world markets will bring in foreign competition instead of relief. The cost of producing zinc from simple zinc ores, by the retort process, will, from the nature of the labor required and the increasing cost of fuel, increase steadily. As a result, the small producers of purely zinc ores around Joplin are shutting down their mines, even with a good market price for zinc; on the other hand, the producer of lead from complex ores, in the Rocky Mountain states, is confident of a profit from the sale of his lead, and is seeking means to make the zinc in his ore pay some part of the cost of treatment. However, the tonnage costs for mining and ore dressing are much higher in the Rocky Mountain states, as may be seen by comparing tax-return statements from the various states. Even before the recent drop in the price of silver, many mines were operating on a very slender margin of profit; labor and supplies cost more. Mining at greater depth has shown most orebodies to grow increasingly more complex, so that improvements in mining and ore-dressing practice have not been sufficient to compensate for the additional expense involved in beneficiating these ores. The smelters have bad to meet the same general economic situation, so they can only give

Jan 1, 1924

By J. Szekely

A rrlethod is presented for the estitnation of oxygen pickup by teettzed molten steel streams. Of the mechanisrt~s considered for oxygen absorption, physical entrainment appeared to be the most significant. The estent of this physical entrainment may be calculated by the application of boundary layer theory. It was found that the values of oxygen pickup thus predicted were in wry good agreement with data reported in the literature, in the case of short, well-defined metal streams. This entrainment model does not provide an adequate description of oxygen pickup by long streams, exoosed to external winds and where breakup of the streatn is likely. WheN molten steel is teemed into a mold or tundish it will absorb oxygen contained in its environment. Recently interest has been expressed in the measurement and possible prediction of the extent of this oxygen absorption: this interest owes its existence to two principal factors: a) the desirability of providing a quantitative assessment of the role played by the absorbed oxygen in impairing the quality of (vacuum degassed. stainless, or continuously cast) steel; b) the need for providing guidelines for stream protection methods. The purpose of this communication is to suggest a simple method for the prediction of oxygen absorption by continuous metal streams and to compare the predicted values with the data available in the literature. It is hoped that this method may provide at least an initial framework for the interpretation of additional data that might become available. FORMULATION Consider a continuous metal stream falling into a molten metal pool as depicted in Fig. 1. This system may absorb oxygen due to the following two mechanisms: 1) physical entrainment of gases (including oxygen) into the molten pool where reactions. thus absorption, will occur; 2) mass transfer (convec:tive diffusion) of oxygen to the metal stream. 1) Physical Entrainment. The physical entrainment may be calculated by using the concept of the diaplace-ttzent tlzickness of the laminar boundary layer, which will be stated briefly in the following.&apos; When a fluid flows past a solid surface, a portion of the fluid close to the surface is retarded due to fric-tional forces. This region in which the velocity of the fluid differs from that in the main stream is called the boundary layer. An illustration of this is given in Fig. 2 where it is seen that the thickness of the boundary layer increases as we move along in the x direction. In the laminar region, when Re, < 10&apos; the thickness of the boundary layer is given by the following relationship: f =4.64 Re;1" [1] where 61 is the boundary layer thickness, x is the length along the leading edge, Us is the velocity of the free stream, (i is the viscosity of the fluid (gas in this instance).

Jan 1, 1970

By Henry N. Doyle

Basic procedures in the mining industry have changed only slightly over the centuries since metals and fossil fuels became an essential part of man&apos;s economic and cultural life. Mining techniques of the 20th century bear a close resemblance to those of the ancients: exploration, ore breakage and removal, hoisting, and processing. The great advances, however, have been in equipment and machinery of greater size and speed which allow greater efficiency in each of these operations, with a corresponding reduction in manpower requirements. Yesteryear production was measured in pounds per man-day; today a giant and complex, but highly efficient, continuous mining machine can remove as much as eight tons of material a minute from the coal face. If our energy and metal demands of the future are to be met, and at this time it can be assumed that coal will continue to supply a significant part of the energy demand, other dramatic and spectacular technologic advances must be accomplished. Along with mechanization, however, public policy will require the industry to place greater emphasis on health and safety protection, as has been well demonstrated by recent actions of Congress. Together, fossil fuels and metals formed the basis for the industrial revolution-coal to develop power and metals to transform power into useful energy. Strangely enough, however, the mining industry the world over has lagged behind the continuous social changes brought on by the industrial revolution, such as preventive health and industrial hygiene services, and other programs directed to the well-being of the worker. In some countries this resistance, to change may have led in part to the nationalization of the coal industry. Whether this disinclination to social change in the industry of the United States reflects managerial attitudes, inept labor leadership, government neglect, or economic relationship would be the subject of an interesting study. Doubtless the mores of miners and their resistance to change, as well as their geographic isolation from other industrial groups, may have had a strong influence on these factors. In every major coal mining country the accident rate in the coal industry is substantially higher than other industrial groups, and the cost of pneumoconiosis compensation in some countries is greater than the combined costs for all other occupational diseases from all other industries. The high social cost of occupational accidents and diseases may have been a factor in the closing of the industry in at least two countries. Despite diminishing manpower needs, the industry is faced with critical manpower shortages. Miners once reared their sons to be miners; now it appears that the opposite is true. This factor alone, however, does not explain an acute labor shortage in the industry. Traditionally, the industry drew much of

Jan 1, 1976

By William P. Blake

It is scarcely necessary to point out the important functions of water in the mining operations of man, especially in the State of California, where sluicing and hydraulic mining have been practiced on such a grand scale as to arouse the opposition of the agricultural interests. But the role which water and ice have played in mining or excavating on their own account is not so apparent. The alluvions of existing rivers, and the higher gravel-beds left by ancient streams, are doubtless the result of running water; but how far these gravelly materials owe their origin primarily as rocky debris and fragments of veins to glacial erosion, it is difficult .to determine. Yet we see on every side in our higher mountains unmistakable evidences of the cutting, crushing and eroding effects of glacial ice. We note that mountain-summits have been reduced in height and shaped into rounded and dome-like summits. We know that the general contour of the hills of New England, of the Highlands of the Hudson, and of the mountains of northern New Jersey, is due to glacial carving. The same is true of the Laurentian hills of Canada and of the mountains of all northern regions. And we recognize in the vast deposits of so-called " drift," which are spread out over the surface of the northern States, the chips and debris from the glacial workshops. Thus we cannot avoid the conclusion that there was an enormous amount of cutting and excavating in glacial times, and that vast quantities of veinmaterial and of ores and metals must have been liberated by ice-action.

Jan 1, 1900

By B. K. Mozumdar

This paper describes the development and application of a dynamic simulation model of ground movement in an underground mine. Ground movement and related stress distributions with or without stowing are computed as the mining face advances. Pressure profiles plotted for different face positions indicate the presence of a front abutment with a maximum value of four times the original ground pressure but no back abutment in the gob. The surface strain is considerably reduced with increase in packing density in the gob up to a certain value. Beyond this value, the reduction in the strain is minimal, indicating an economic level of packing. As a result of model experiments with different physical systems and geological parameters, it has been concluded that when one of the coordinates for the subsidence and the strain curves is made dimensionless in terms of the critical width, the relationship will hold true for all physical situations. This was in agreement with the NCB observations for different panel lengths.

Jan 1, 1977

By Emma Smith, R. W. Guard

INVESTIGATION of the nickel-rich end of the Ni-Zr system has been prompted by an interest in the effect of small amounts of zirconium in high temperature alloys. Hansenl presents a hypothetical diagram based on the work of Allibone and Sykes,2 who investigated the system up to 44 atomic pct (55 wt pct) Zr by metallographic means. Since the alloys they used were melted in Alundum crucibles they were probably contaminated with appreciable amounts of aluminum. They found two compounds which they called Ni3Zr and Ni4Zr. Hayes, Roberson, and Paasche3 identified a compound NiZr (50 atomic pct Zr) with a melting point of 1470°C. Such a high melting compound is not compatible with the observation of Allibone and Sykes2 hat a eutectic is formed near 50 atomic pct. The alloys containing up to 60 atomic pct Zr were melted in an inert atmosphere in a noncon-sumable electrode arc furnace. Analysis of most of the alloys indicated negligible loss of zirconium. The alloys were examined in the as-cast condition and also after annealing for 6 hr at 1175°C (or 1000°C for the alloys between 25 atomic pct and 45 atomic pct). Metallographic specimens were etched using mixtures of HF-HNO3-H2O or acetic acid- HN0,-H,O. The specimens for the solidus determinations were wrapped in molybdenum foil and sealed in evacuated quartz tubes. Specimens to be heated above 1300°C were enclosed in zirconia tubes inside the quartz to prevent reaction with molybdenum. The solidus determinations were carried out by heating the specimens at various temperatures for a few minutes and then examining the interior structure metallographically to determine at what temperature melting began. The 150 mesh powders for X-ray analysis were annealed in an evacuated quartz tube for 2 hr at 540 °C to remove cold work. Alloys with 22.5 atomic pct Zr and 44.4 atomic pct Zr required annealing at 700 °C for complete recovery. The grains of both of these alloys were soft and rather ductile. Both Debye-Scherrer film patterns and spectrometer traces were made for each alloy using filtered copper radiation. Results and Discussion The presence of a substantial amount of second phase in an alloy with 1.1 atomic pct Zr indicated that the solid solubility of zirconium in nickel is somewhat less than 1 atomic pct. The a0 value for the face-centered-cubic matrix in the same alloy was equal to that of pure nickel, so that the solubility must be very small. This observation is as expected from the large atom size difference. Annealed specimens of alloys with 15.0, 16.7, 22.5, 28.6, 44.4, and 59.4 atomic pct Zr showed. micro-structures that were essentially single phase. When

Jan 1, 1958

By George W. Healy, Ko Yamaguchi

In typical calorimetry the energy given off by a material under study is transferred to a water bath, whose temperature is sensed by a thermometer; for correct measurement the water bath must attain a uniform temperature to which the thermometer must respond. This introduces two sources of error, non-uniformity of the heat sink and a time lag until its temperature is registered. These errors may become important where a rapid process such as solidification of metals and alloys is being studied by means of Oelsen&apos;sl quantitative thermal analysis. To overcome this difficulty, a calorimeter sink was conceived in which the water bath is replaced by a copper coil, which serves simultaneously as heat

Jan 1, 1967

By R. E. Zimmerman

Wide attention is being placed upon various methods for cleaning the fine sizes of bituminous coals. The author describes and analyzes the results achieved on wet concentrating tables of modern design on unclassified feeds of —Vz in. particle sizes, including tests on high-sulphur coals. THE increased economic necessity of cleaning the small sizes of coal has forced wide attention upon various methods or processes being used. Although numerous cleaning plants in the past have been cleaning coal smaller than Vz or % in., the large quantities of higher ash fines being produced by mechanical mining and the need for cleaner coal under competitive market conditions have brought about many new installations of fine-coal cleaning plants. Of various methods used, one of the more popular types is the wet concentrating table. Approximately 525 tables have been installed in the United States in the past four years of which 320 have been installed in 20, large new plants. There are now probably 1600 tables of all types in existence in this country for cleaning coal. The purpose of this paper is to describe the cleaning of fine coal by wet concentrating tables. Its scope is confined to a discussion of the theory of tabling and some of the factors entering into tabling action, a description of the Deister SuperDuty diagonal-deck coal table and a discussion of the results of tabling various fine sizes of coals. Al- though tables have been used for cleaning coal as coarse as 2 in. and favorable results are reported, this paper is limited to reporting on the results of cleaning coal fines from 1/2 in. down. Also, although it is well known that the performance of tables is even superior under classified or closely sized feed conditions, this paper concerns itself with the results achieved by tabling unclassified feeds. History of Wet Concentrating Tables The wet concentration of minerals by some form of tabling is quite old, starting originally from fixed, smooth surfaced, tilted boards taking advantage of the laminar flow of liquid films and the separation of minerals according to specific gravity. This was followed by the development of rough deck surfaces

Jan 1, 1951

By R. E. Zimmerman

Wide attention is being placed upon various methods for cleaning the fine sizes of bituminous coals. The author describes and analyzes the results achieved on wet concentrating tables of modern design on unclassified feeds of —Vz in. particle sizes, including tests on high-sulphur coals. THE increased economic necessity of cleaning the small sizes of coal has forced wide attention upon various methods or processes being used. Although numerous cleaning plants in the past have been cleaning coal smaller than Vz or % in., the large quantities of higher ash fines being produced by mechanical mining and the need for cleaner coal under competitive market conditions have brought about many new installations of fine-coal cleaning plants. Of various methods used, one of the more popular types is the wet concentrating table. Approximately 525 tables have been installed in the United States in the past four years of which 320 have been installed in 20, large new plants. There are now probably 1600 tables of all types in existence in this country for cleaning coal. The purpose of this paper is to describe the cleaning of fine coal by wet concentrating tables. Its scope is confined to a discussion of the theory of tabling and some of the factors entering into tabling action, a description of the Deister SuperDuty diagonal-deck coal table and a discussion of the results of tabling various fine sizes of coals. Al- though tables have been used for cleaning coal as coarse as 2 in. and favorable results are reported, this paper is limited to reporting on the results of cleaning coal fines from 1/2 in. down. Also, although it is well known that the performance of tables is even superior under classified or closely sized feed conditions, this paper concerns itself with the results achieved by tabling unclassified feeds. History of Wet Concentrating Tables The wet concentration of minerals by some form of tabling is quite old, starting originally from fixed, smooth surfaced, tilted boards taking advantage of the laminar flow of liquid films and the separation of minerals according to specific gravity. This was followed by the development of rough deck surfaces

Jan 1, 1951

By V. I. Purcell, S. C. Sun. R. E. Snow

A study including effects of 7) pH value, 2) fatty acid collector, 3) fuel oil, 4) interfering ion, 5) particle size, and 6) operational variables. Test results indicate feasibility of fatty acid flotation under certain restrictive conditions. FATTY acids have been used as standard collectors for floating the matrix1-8 but not the leached zone phosphate ores. After a series of investigations, Davenport9 and Tarbutton10 concluded that the Florida leached zone ores tested were unamenable to fatty acid flotation and must be upgraded by floating the siliceous gangue with Armac-T as collector. The cationic flotation was estimated11 to cost almost ten times as much as a fatty acid process that would ideally give the same flotation grades and recoveries of phosphates. Mineralization: Extensive deposits of leached zone aluminiferous phosphate occur in Florida."= The ore sample used for this work was obtained from the Virginia-Carolina Chemical Corp., Clear Springs area, Florida. The ore is a potential source of uranium and aluminum as well as phosphorus. Since the uranium and the recoverable aluminum are contained in some of the phosphate minerals, an upgrading of phosphate results in a corresponding enrichment of both uranium and aluminum. The phosphate minerals in the ore are primarily pseudo-wavellite, millisite, and carbonate fluorapatite, with a minor amount of wavellite. Quartz and clay are the common gangue minerals, quartz being predominant. Others present in small amounts are ilmenite, hydrated iron oxides, staurolite, monazite, and zircon. Experimental Procedures: After being dried to less than 1 pct surface moisture the material was dry-ground in a Hardinge conical ball mill to —6 mesh. The ground product was classified into 6/20, 20/200, and —200 mesh size fractions. On the basis of Table I, the coarse and fine size fractions were considered as phosphate concentrates, because of their high phosphorus contents. In contrast, the 20/200 mesh fraction, which was low in phosphorus, was used as the flotation feed. All the flotation tests, unless otherwise stated, were performed in a laboratory Fagergren machine under the following conditions: 1) 400 g of solid feed for each test, 2) 2000 rpm impeller speed, 3) 8.9 pH and 4-min conditioning, and 4) 3-min flotation. The procedure used for the quantitative bubble pick-up tests has been described previously.18

Jan 1, 1958

By William Fink

Two of the aluminum-alloy systems previously studied-the alumi-num-titanium and the aluminum-chromium-exhibit a peritectic reaction at the extreme aluminum end of the diagram. Preliminary work indi-cated that the aluminum-zirconium and certain other aluminum systems were similar in this respect. The present paper, the twentieth of a series from the Aluminum Research Laboratories, reports the results of a recent investigation of equilibrium relations in aluminum-zirconium alloys of high purity, which confirm the preliminary observations. PREVIOUS INVESTIGATIONS There has been only one investigation of the aluminum end of the aluminum-zirconium system. Sykes1 prepared and studied alloys containing 0 to 70 per cent Zr. The lowering of the freezing point of aluminum by the addition of zirconium was found to be very little, if any (less than 2°C.). He placed the solid solubility of zirconium in aluminum at room temperature between 0.57 and 0.97 per cent. A few other investigators have attempted to determine the com-position of the intermetallic compounds occurring in this system. Hönigschmid2 obtained the compound ZrAl3 as a by-product during the preparation of ZrSi2. He made no attempt to prepare other aluminum-zir-conium compounds. Weiss and Newmann3 prepared an alloy by heating aluminum with a double fluoride of potassium and zirconium. When this alloy was treated consecutively with caustic soda and hydrochloric acid, there was a residue, which contained approximately 72 per cent Zr and 28 per cent Al (Zr3Al4). Marden and Rich4 prepared an alloy in the same way, treated it with caustic soda, and obtained a residue of silver-white crystals, which contained 70 per cent Zr and 30 per cent Al (Zr3Al4).

Jan 1, 1939

By F. D. Richardson

STAFF: Editor, Gerhard Derge Carnegie lnstitute of Technology Schenley Park Pittsburgh, Pa. 15213 Editorial Assistant, M. A. Redmerski Production Editor, Otto T. Johnson THE METALLURGICAL SOCIETY: Jack H. Scoff, President; Richard C. Cole, Past-President; Harold 0. Emerick, President-Elect; Ralph L. Hennebach, Treasurer; Robert W. Shearman, Secretary; Donald A. Parks, Assistant Secretary; Leslie S. Wilcoxson, Assistant Secretary. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: R. E. Lund, Chairman; T. E. Dancy, H. O. Emerick, P. R. Gouwens, R. E. Grace, J. H. Jackson, H. H. Johnson, A. E. Lee, Jr., R. R. Nosh, R. D. Pehlke, and Paul Queneau. Review and selection of manuscripts is under the supervision of the following Publications Committees: Extroctive Metallurgy Division: R. E. Grace, Choirmon; G. M. Bell, D. W. Bridges, J. M. Cigon, G. W. Heoly, T. A. Henrie, R. D. (Holli-doy, C. E. O&apos;Neill, C. S. Somis, A. W. Schlech-ten, and Charles Shull. Iron and Steel Division: R. D. Pehlke, Choirmon; T. P. Floridis, Arnulf Muon, G. R. St. Pierre, E. T. Turkdogan, L. H.Von Vlock, and J. M. Uys. lnstitute of Metals Division: H. H. Johnson, Jr., Chairman; J. B. Clark, Vice Choirmon; M. R. Achter, G. F. Bolling. J. O. Brittoin, G. P. Conard, II, R. S. Davis, L. A. Girifolco, G. T. Hohn, J. P. Hirth, L. Himmel, G.T.horn, George Krauss, J. D. Livingston, R. D. Manning, H. M. Otte, S. V. Rodcliffe, R. E. Reed-Hill, H. C. Rogers, E. ScaIa, O. Sherby, M. T. Simnad, G. R. Speich, E. A. Steigerwald, R. A. Swolin, W. A. Tiller, W. R. Upthegrove, J. B. Wagner, Jr., Derek Wolton, H. W. Weart, W. W. Webb, and D. Published seven times yearly in February, March, April, June, August, October, and December by the American lnstitute of Mining, Metallurgical, and Petroleum Engineers, Inc., 345 East 47th Street New York, N. Y. 10017. Telephone PLAZA 2 -6800. Subscription $30 per year for non-AtME members m United States and North, South, and Central America; $32, foreign; $7.50 for AlME members Single copies, $6.00, single copier foreign, $6.50. The AiME is not responsible for any statement made or opinion expressed in its publications . . . Copyright 1964 by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. . . . Registered cable address, AiME New York Indexed in Engineering Index, Industrial Arts Index, and Chemical Abstracts. Second dost postaas poid ot New York, N. Y.,ond Ann Arbor, Mich. Volume 230, Number 6.

Jan 1, 1964

By Howard N. Eavenson

FROM the Pittsburgh coal bed in the four states of Pennsylvania, Ohio, Maryland and West Virginia has been produced an output that, at mine prices, represents a greater value than any other single mineral deposit in the world has yielded.12 While this distinction may in a few years pass to the gold reef of the Witwatersrand, it is possible that eventually, owing to the tremendous reserves still remaining, the ultimate yield of the Pittsburgh bed will be greater than that of any other known single deposit. Considering its importance, not a great deal has been written of its early history and development as a whole; most of the accounts have been of limited localities, or, at the most, of the area within a single state. In "Coal through the Ages" the writer mentioned some references to its early history, but this study will deal not only with its history but with the character of the bed, where and why it was first developed, and its effect upon the states in which it is found. It has not been the intention to write a detailed history of the development of the seam in each locality, as neither time nor inclination were available for doing such work, but only to show the influences that tended to hasten or retard such development. In general the historical matter ends about 1830, when geological surveys began to be made. Some of the maps show data available only since that time, and the sections about coal preparation and coking have been extended to the present time to show the changing conditions. It is believed that the early history includes all published records, and many more sources than those shown in the bibliography were consulted. It is quite likely that some references to coal in this area may be found in the unpublished papers of some of our early soldiers and colonizers, which exist in several libraries, and it is hoped that some future

Jan 1, 1938

By Ward W. Minkler

Since 1978, the titanium metals industry, throughout the non-socialist world, has experienced a period of growth and prosperity unparalleled since the late 1950s. Sponge producers, melters and mill product manufacturers have operated at capacity, record shipments have been attained, new producers have entered the industry and established producers have implemented expansion plans. However, there is now mounting evidence that the underlying elements which generated this vigorous surge have abated, at least temporarily. It now appears that in 1982, the industry will encounter overcapacity, excessive inventory accumulations and the probability of declining prices. Therefore, it does seem appropriate that we now take inventory of the present and future markets for titanium with the hope we can identify both near term opportunities as well as challenges the industry now faces. If we view the development of titanium markets as a function of time, they fit rather neatly into three sectors.

Jan 1, 1982

By R. L. Lloyd

UNLIKE the development of sintering lead, copper and zinc ores, the sintering of fine irony material had its birth, not as a result of gradual growth along lines aimed at the production of sintered and agglomerated product, but because the success of the sintering operation in other lines had been brought to the attention of the ironmasters, who were immediately attracted by the prospect of being able to convert their own fines-into a similar product. The abundance of iron ores in the United States and their comparative cheapness had led iron men into the habit of not paying particular attention to the fine material blown out of their blast furnaces. Hundreds of thousands of tons had been stacked up and used only during times of shortage of ore and then usually without any preliminary preparation, though many attempts had been made to briquette it. Briquettes proved good material, but the operation of briquetting was too expen-sive when applied to iron-ore fines. The development of the iron-ore blast furnace in the United States tended toward large units, high columns and heavy blast pressure, and this tendency is still peculiar to this country, whereas in the other countries the tendency has been to smaller units, lower columns and lower blasts. The high blast pressures and swift driving of the American blast furnace tend, of course, to produce more flue dust than European practice, and this production of flue dust was augmented when large quantities of soft ore, of which the Mesabi is typical, came on to the market. These ores are desirable chemically but physically they are soft, friable and fine, and when they are used in the iron blast furnace the flue dust produc-tion is increased. The necessity of rehandling the flue dust lead to briquetting on an extensive scale. The binders used were either chemical or mechanical, and in one system the briquettes were kiln fired in very high temperatures. Rotary kilns, coal or oil fired, were used extensively, and gave a product of hard and more or less nodulized material, but at considerable cost. This was the situation in regard to iron flue dust when the late James Gayley and his associates became interested in the idea of sintering the iron blast-furnace flue dusts under their own fuel (included coke dust) of which they carried between 15 and 30 per cent.

Jan 10, 1922

[ ]

Jan 1, 1940