Search Documents

By W. E. Horst

Flotation feed was hell constant for batch laboratory tests and continuous pilot and commercial plant tests on a spodumene ore to determine the relation.ship between flotation behavior and the size and type of flotation machine. Results. showed that additional retention time would be needed in the plant flotation circuit to duplicate laboratory or pilot plant performance when operating Dariables of the. plant flotation machines remained unchanged. During the past few years of operation at Kings Mountain, N. C., full-scale flotation has generally yielded poorer metallurgical results than those obtained in the laboratory or pilot plant. After 2 min in each size of Denver flotation machine in the spodumene rougher circuit, pilot recovery (41.7 pct) was almost three times that of the plant (13.6 pct) and about twice that of the laboratory (21.0 pct). Pilot and commercial plant data are based on continuous operation, and laboratory results on batch testing of rougher performance. The ore is a pegmatite containing spodumene, feldspar, quartz, mica, and amphibolite. Data were accumulated to evaluate the scale-up relationships between laboratory, pilot plant, and plant flotation cells. Flotation rate constants and dimensional analysis were used to define the relationship existing between flotation behavior and scale of operation. Measuring Flotation Rates: Efficiency of the rougher stage was measured by flotation rate, defined as the recovery that can be attained within a given time." • The problem of measuring flotation rates has been studied by many investigators, whose methods have varied. Published studies an flotation kinetics have been summarized recently by Gaudin.l When comparing flotation rates, it is more satisfactory to compare straight line relationships between recovery and flotation time than exponential curves resulting from plotting cumulative recovery vs cumulative flotation time. To convert the exponential curves into straight line relationships, rate equations were applied similar to those used in chemical kinetics to study the velocity of chemical reactions. Two rate equations have been used in this investigation to measure efficiency of the various cells: 1.5 order Rate Equation dR/dt=k (A-R)1.0 [Eq.1] Second Order Rate Equation dR ---- - K(A - R)2 [Eq. 2] dt Upon integration Eq. 1 becomes 1/(A-R)1/2=k/2 t+1/A1/2 [Eq. 3] and Eq 2 becomes: or fEq. 4] t/R=1/A2K+t/A [Eq. 4] where R = cumulative recovery [percent recovery of total value (spodumene) in flotation feed]. A = initial concentration, pct (100 pct of mineral to be separated). t = flotation time (minutes). k = flotation rate constant for 1.5 order rate equation [units: 1/(percent) 0.5 (min)1. K = flotation rate constant for second order rate equation [units: 1/(percent) (min) 1.

Jan 1, 1959

By John Garcia

IN some districts of the bituminous coal field the problem of construct-ing bulkheads to seal off water under pressure is becoming increasingly important. Recently this matter has been brought very much to the front by the loss of a large Illinois mine due to failure of a bulkhead that separated it from several old, flooded mines. As this great misfortune has provoked much inquiry about proper bulkhead design, it-is felt that a description, of the successful and extensive water-sealing practice at three mines that have different natural conditions will be of considerable interest to those connected with properties having a present or future water problem and to engineers that may have to design safe bulkheads of economical construction. These three mines are the Saxton and Dresser, near Terre Haute, Ind., and the Hegeler, near Danville, Ill. All three have water conditions that make it necessary to regularly seal off all worked-out sections of the mine, and there are considerably over a hundred bulkheads in each. As far as the writers know, these three mines are the only ones in the bitu-minous coal fields of the United States with anything like so large number of water seals and experience, although a number of other mines are known to have a few bulkheads. More detail will be included herein on the Saxton mine than on the others, as the writers are more familiar with it.

Jan 1, 1937

By J. R. Long, T. R. Graham

THIS report is concerned with part of a series of investigations carried on by the Federal Bureau of Mines on alloys, particularly nonferrous alloys, made with electrolytic manganese. A broad general program instituted after commercial quantities of electrolytic manganese became available was necessary in order to compare the effects of electrolytic manganese with those of the ordinary commercial grades. Representative analyses of these two materials show the commercial manganese metal to contain up to 2 per cent iron, a maximum of I per cent silicon and 0.06 per cent carbon, while the electrolytic manganese rarely exceeds 0.01 iron, 0.02 sulphur, with no silicon or aluminum. In the literature, the emphasis has been largely on high-strength casting alloys containing up to 5 per cent manganese, and few data are available on wrought manganese alloys. These factors, coupled with the strategic position of copper and zinc, have given impetus to the Bureau's War Research Program for the development of alloys containing nonstrategic manganese for the purpose of supplementing or providing alternates for the more strategic metals. The alloy reported here was studied, along with several other ferrous and nonferrous alloys, as possible cartridge-case material, and was chosen after a review of the properties of the ternary alloys of copper-manganese-zinc. PRELIMINARY WORK In a cursory survey of this system, alloys ranging from 60 to 95 per cent copper, 0 to 50 per cent manganese, and 5 to 40 per cent zinc were investigated. The alloys containing 60 per cent copper were found to fall into the two-phase alpha plus beta region of the system, and since those containing 70 per cent would not permit a saving, only alloys containing 65 per cent copper were considered. The tensile properties of these 65 per cent alloys are plotted in Fig. I as a function of manganese content for annealed material and for four conditions of cold-work In the annealed condition the increases in strength and decreases in elongation are minor up to 15 per cent manganese; beyond this, the changes become more significant. In the cold-worked condition, the first 5 to 10 per cent of manganese appears to have the greatest strengthening, effect, the rate of increase dropping off as the manganese increases beyond this amount. These effects are more pronounced with moderate than with severe cold reduction. It is also interesting to note that while the elongation of annealed material drops regularly with increasing manganese, the elongation in the cold-worked state is relatively little affected by increasing manganese content, particu-

Jan 1, 1944

By Robert Gillham, Victoria Yablonsky, Grover R. Castle

INTRODUCTION The commercial paper market, unique to the United States, is a direct exchange of funds between high-grade borrowers and large lenders; because it eliminates both the bank's role as middleman and also some significant transaction costs, commercial paper is the lowest cost short term instrument in the world. For this reason, virtually all borrowers would like to enter the market, but only issuers with the highest rating from Moody's and Standard & Poor can attract purchasers at the best rates. COMMERCIAL PAPER The commercial paper market, in existence for over 100 years, has traditionally been used for short-term financings, with most paper maturing within 30-45 days. Under the U. S. Securities Act of 1933, (section 3(a)3) industrial paper can avoid registration only if it matures within 270 days and is used for current transactions. It was first used to finance the short-term seasonal working capital needs of manufacturing companies. Since World War II, commercial paper use has grown steadily, serving in the 1950's as the market in which finance companies financed the explosion in consumer credit purchases of heavy consumer durables. LETTER OF CREDIT BACKING As far as is known, the use of letters of credit to support energy-related commercial paper began about 13 years ago with an arrangement to finance the nuclear fuel for Con Edison's Indian Point 3 Plant. Goldman, Sachs was the architect of this financing and Chemical Bank provided the letter of credit support. After an early burst of interest, this type of financing wobbled severely in the difficult credit markets of the mid-seventies before regaining serious momentum in 1976 and 1977. A mining project would not normally qualify as a borrower in the commercial paper market because of its credit standing and because its large capital needs require long term financing. However, lately, commercial paper has begun to take the place of a bank term loan in limited recourse project financings. L/C backed commercial paper took this new and startling turn in 1982 when it was used as part of the $700 million financing for the development of the Newlands-Collinsville coal mines of Mount Isa Mines Ltd. in Australia. This was the first use of L/C backed commercial paper in a long-term limited recourse project financing. First Boston acted as financial advisor and, again, Chemical Bank provided sole letter of credit support of $155 million. The $785 million BHP financing for the acquisition of the Queensland (Australia) coal assets of Utah International from General Electric Company followed the next year; there we acted with two other Front Banks to provide $270 million of L/C support. These two important transactions indicate that not only has commercial paper become an integral part of a long-term financing package, but also that it is no longer the exclusive domain of the best known U. S. companies. Lesser-rated companies and a multitude of foreign borrowers have gained access to this "exclusive club." How has this become possible? OPERATION OF AN L/C An instrument of the commercial banks, the "direct pay" letter of credit, has enabled lesser-rated companies to issue commercial paper in their own names. The letter of credit allows the issuer to substitute the credit rating of the supporting bank for its own. The L/C in effect allows a lesser-rated company to rent the bank's credit rating. This upgrading is possible because the bank is unconditionally obliged to pay the note-holders at maturity and then turn to the Issuer for reimbursement. The Issuer commonly "rolls over" a new short-term issue and reimburses the supporting bank from the sale of the new issue until cash flows from the project allow the borrower to reduce the level of paper outstanding. The commitment for an L/C facility, up to 12 years in the case of the Broken Hill transaction, governs the life of the commercial paper tranche of the financing. The term of the L/C commitment thus has the power to extend the ordinary 30-45

Jan 1, 1985

By O. D. Sherby, J. E. Dorn

SEVERAL years ago Zener and Hollomon1 suggested that the flow stress of metals might be related to the temperature and strain rate in accord with the functional equation: s=s(eeh/rt) [1] at the same state. The Zener-Hollomon relation also contains the significant tacit implication that the energy for activation, AH, is substantially independent of the state of the material. The utility of this method for correlating creep data with tensile data was illustrated in a preliminary reportL on the effect of alloying additions on the secondary creep rates of binary a solid solutions in aluminum as shown for Al-Mg alloys in Fig. 1. Not only do the secondary creep and ultimate tensile properties for each alloy correlate well on this plot but in addition the activation energy, AH = 17,900 R cal per mol. is identical for the various compositions. Similar types of curves correlating the secondary creep rates at 422°K (300°F) with ultimate tensile data were also obtained for a series of dilute a solid solutions of copper, germanium, zinc, and silver in aluminum. In all cases the activation energy for creep, AH, was found to be equal to about 17,900 R cal per mol independent of the type of alloying element or its concentration. The coincidence of the activation energies for these alloys is probably due to the fact that the activation energies for creep are rather insensitive to small composition changes. Alloying additions, as shown in Fig. 1, however, increased the stress necessary to obtain equivalent values of ee?H/RT. Thus the stress level in curves of the type represented by Fig. 1 gives the relative creep strengths of the various alloys. Inasmuch as these correlations between creep and tensile data were obtained for creep tests at 422°K, it appeared advisable to ascertain the range of secondary creep rates and temperatures over which correlations between creep and tensile data could be made on the basis of the Zener-Hollomon relationship. If, for example, the activation energy changes with different ranges of creep temperatures, the utility of the proposed analysis would be severely weakened. But if AH is constant not only for all dilute alloys, but also over wide ranges of temperature and secondary creep rates, confidence will be developed not only in the broad utility of the Zener- Table I. Chemical Analysis':' and Grain Size of Alloys Mean Grain Residual Impurities. Wt Pct Diam- Alloying Atomic-eter, Element Pct Si Fe Cu Mg Mn mm Aluminum 99.987 0.003 0.003 0.006 0.001 0.25 Magnesium 1.617 0.003 0.004 0.006 0.26 Copper 0.101 0.003 0.003 0.0006 0.001 0.29 Zinc 1.616 0.003 0.005 0.007 0.001 '0.26 * The authors express their appreciation to the Aluminum Company of America for the preparation and chemical analyses of these alloys. Hollomon relationship, but also in its theoretical justification. The following investigation was instituted in order to ascertain the range of validity of the Zener-Hollomon relationship when it is applied to creep and tension data. Materials, Equipment, Technique In view of rather extensive correlatable data now available on the plastic properties of a series of binary a solid solutions of magnesium, copper, germanium, zinc, and silver in aluminum, these alloys were again selected for the present investigation. Previous reports have already covered the tensile properties of these alloys at subatmospheric temperatures," and at elevated temperature," as well as their fatigue properties at atmospheric temperatures, nd their creep properties at 422°K.' Resistivity measurementsa as well as precision lattice constant determinations? evealed that these alloys are a solid solutions. After homogenization. 0.100 in. thick sheets were rolled to 0.070 in. in thickness and recrystallized to about the same grain size. Since the details of these treatments were reported previously," they will not be repeated here. In order to appropriately reduce the scope of creep tests in this investigation only the typical alloys shown in Table I were investigated. All creep specimens were machined such that their tensile axes were in the rolling direction of the 0.070 in. sheet stock. The gage section was 2 in. long and 0.500 in. wide with a reduced section of 3.50 in. Creep strains were measured by means of rack and pinion type extensometers with a sensitivity of 0.005 in. per division. Readings were estimated to 1/10 of

Jan 1, 1953

By J. C. Detweiler

THE Jacksonville plant of Humphreys Gold Corp., operating under leases from National Lead Co. and Rutile Mining Co. of Florida, recovers rutile, ilmenite, zircon, and monazite from an ancient beach deposit containing about 2.5 pct of these minerals in combination. The location of the plant is unique, being situated about ten miles from the center of Jacksonville, Fla., surrounded by a thriving suburb. Two four-lane highways pass within 1 ½ miles of the plant. An expressway now under construction will pass over the tailing pile, within 500 ft of the mine office. The elevation at the plant site is approximately 50 ft above sea level. This is one of two mines producing titanium minerals and zircon in Florida. Another mine is also operated by Humphreys at Starke, about 50 miles southeast of Jacksonville. The Jacksonville deposit extends about six miles in a north-south direction, averaging approximately one half mile wide and twenty ft thick. Values begin at the surface over most of its length and ter-

Jan 1, 1952

By Roscoe C. Clark, Henry F. Coffer, J. J. Reynolds

A cement slurry lightweight additive has been adapted in the Conoco laboratories for use in oil well cements. This additive makes possible the use of air to lighten oil well cement slurries. Specifically, the additive consists of small clay bubbles of air having sufficient strength to resist crushing by bottom hole pressures. Clay bubble cement slurry weights can be safely reduced to 10 Ibs/gal. In addition, the clay bubbles tend to act as lost circulation materials and to provide a cement texture which should produce good perforating characteristics. Clay bubble cement is relatively impermeable. INTRODUCTION In many areas in Oklahoma, Texas, Wyoming, and California, difficulties are experienced during casing cementing operations with lost returns caused by the high density of the cement slurries. Wells in these areas are ordinarily drilled with 9 to 11 lbs/gal. drilling mud while neat cement slurries may range in densities from 14.5 to 17 lbs/gal. In these areas, cement slurry weights are at present being successfully reduced to around 12 lbs/gal. (under bottom-hole conditions) by the use of additives in the cement. Since the use of additives will decrease the strength which the cement will develop, the amount of additives which can be used must be based on the minimum cement strength which is acceptable; and thus the maximum slurry weight can be reduced. At present, the minimum tensile strength generally acceptable is 50 lbs/sq in. cured for 24 hours under bottom-hole temperature. This figure is based on laboratory tests1 and on a large number of cement jobs which have been conducted using cement which will not develop more than 50 psi tensile strength in 24 hours under bottom-hole conditions. Two additives are now in use for decreasing cement slurry weights. These are expanded perlite and/or bentonite. The density of both of these materials is greater than that of the cement slurry; however, large quantities of water may be added with these materials without producing a slurry which will settle out of suspension. It is these large quantities of water which contribute to the reduction in the slurry weight. The minimum slurry weight at present obtainable with expanded perlite and/or bentonite is approximately 12 lbs/gal. using a standard Portland cement slurry. In many areas, this weight reduction is insufficient; and returns are still lost during casing cementing operations. In many cases, the pay formation itself is fractured; and a considerable quantity of this cement is lost to the pay zone. It is therefore believed that if cement slurry weights can be reduced to as low as 10 lbs/gal., two advantages will accrue: 1. The lighter densities (10 to 12 lbs/gal.) should mitigate or eliminate lost returns during casing cementing operations. 2. Cement slurries above 12 Ibs/gal. (the present minimum limit ) should develop considerably more strength than is now being obtained. A tensile strength of 100 psi is desirable.' It is the object of this paper to describe a cement slurry having a weight of 10 lbs/gal. and capable of

Jan 1, 1955

By G. M. Kirwan, Joseph B. Perry

MagnEsitE is found in 22 California counties, but many of the deposits are too small or too impure to be of commercial value. Several of substantial size and quality were entirely exhausted by wartime operation. At present, three properties comprise the only known workable deposits in the state. Of these, the Western mine and the Patterson mine have been known and worked for many years, and have been described in considerable detail in various publications, therefore need only brief mention here, because of their proximity to the Bald Eagle mine. The latter, recently developed, is unusual in type of ore deposit, plant design and operation, as well as products made, and very little has been written concerning it. WESTERN MINE The Western mine, 32 miles south of Livermore, Calif., was formerly operated by C. S. Maltby. It has been a consistent producer for many years.l The ore is of amorphous variety, occurring along fracture zones in serpentine. The veins vary greatly in width, the average being perhaps 8 ft., with the maximum indicated in one early stope of 40 ft.; 2 ft. is considered the minimum for economical mining. The strike of the veins is predominantly north and south, with dip to the west varying from 40" to 75". Walls are well defined and as a rule firm and easily supported. Veins range in length from a few hundred feet to 1000 or more. Their maximum vertical extent is about 350 ft., but many run less. Early mining consisted of open-cut and glory-hole work on the larger outcrops. This was followed underground by a modified shrinkage system, the waste and low-grade horses being removed by hand sorting on the tramming levels and transported to surface dumps. Filled-stope mining is used now, in order to eliminate the handling of waste, which has

Jan 1, 1942

By Joseph B. Perry, G. M. Kirwan

MagnEsitE is found in 22 California counties, but many of the deposits are too small or too impure to be of commercial value. Several of substantial size and quality were entirely exhausted by wartime operation. At present, three properties comprise the only known workable deposits in the state. Of these, the Western mine and the Patterson mine have been known and worked for many years, and have been described in considerable detail in various publications, therefore need only brief mention here, because of their proximity to the Bald Eagle mine. The latter, recently developed, is unusual in type of ore deposit, plant design and operation, as well as products made, and very little has been written concerning it. WESTERN MINE The Western mine, 32 miles south of Livermore, Calif., was formerly operated by C. S. Maltby. It has been a consistent producer for many years.l The ore is of amorphous variety, occurring along fracture zones in serpentine. The veins vary greatly in width, the average being perhaps 8 ft., with the maximum indicated in one early stope of 40 ft.; 2 ft. is considered the minimum for economical mining. The strike of the veins is predominantly north and south, with dip to the west varying from 40" to 75". Walls are well defined and as a rule firm and easily supported. Veins range in length from a few hundred feet to 1000 or more. Their maximum vertical extent is about 350 ft., but many run less. Early mining consisted of open-cut and glory-hole work on the larger outcrops. This was followed underground by a modified shrinkage system, the waste and low-grade horses being removed by hand sorting on the tramming levels and transported to surface dumps. Filled-stope mining is used now, in order to eliminate the handling of waste, which has

Jan 1, 1942

By J. E. Tiffany

FOR blasting in coal mines the U. S. Bureau of Mines recommends that permissible explosives be used exclusively, that these shall be fired electrically, and that where feasible the working place shall be cut or sheared. These recommendations are made to promote safety and prevent mine explosions. Although permissible explosives are not flameless, their lower flame temperature and shorter duration of flame make their use safer than that of non-permissible explosives. Mixtures of air with both methane and bituminous coal dust, which are liable to occur in coal mines, may be ignited by coming in contact with any type of flame or spark of sufficient temperature and duration or by the firing of a blast. In a working place where a blast is to be fired, in addition to the use of permissible explosives, adequate ventilation for the dilution and removal of accumulations or outbursts of flammable gas should be provided. Bituminous coal mines should be rock-dusted as a means of rendering the coal dust harmless. The efficient use of permissible explosives depends upon the proper preparation of the working place, standardized drilling, the strength characteristics of the explosive, and the use of a proper weight of charge. Experienced shotfirers should load, tamp and fire all holes. The major part of the information and data here presented is based on the results of efficiency tests made in large producing mines of Pennsylvania and Illinois. Bureau of Mines Report of Investigations, Serial No. 2697, describes how a standard method of blasting was worked out and put into operation in a mine in southern Illinois.1 This paper contains a description of the methods worked out subsequently in another mine in that district.

Jan 1, 1928

By W. H. Bassett

ABOUT twenty-five years ago the copper industry had outgrown the Lake Superior production. The electrolytic copper producers had- their process well in hand and the industry was well started in the use of electrolytic copper, both for working into wire and sheet, and for the making of alloys. The trade knew that some brands of copper made good material and that other brands did not. There came together a group of men-a refiner, a rolling-mill man, and a manufacturer of electrical machinery-each of them desiring to know why there was a difference and what .it was. Much investigation was done with wire bars and cakes which involved ' chemical analysis, metallographic examination, physical tests and electrical tests. To find the influence of different kinds of copper in making brass 200 carloads of ingots were made into ,eyelet brass under careful observation; each carload was carefully analyzed and tested before used. The alloy was made and rolled under standard conditions and the results recorded.

Jan 1, 1924

By T. R. Graham, J. R. Long

This report is concerned with part of a series of investigations carried on by the Federal Bureau of Mines on alloys, particularly nonferrous alloys, made with electrolytic manganese. A broad general program instituted after commercial quantities of electrolytic manganese became available was necessary in order to compare the effects of electrolytic manganese with those of the ordinary commercial grades. Representative analyses of these two materials show the commercial manganese metal to contain up to 2 per cent iron, a maximum of I per cent silicon and 0.06 per cent carbon, while the electrolytic manganese rarely exceeds 0.01 iron, 0.02 sulphur, with no silicon or aluminum. In the literature, the emphasis has been largely on high-strength casting alloys containing up to 5 per cent manganese, and few data are available on wrought manganese alloys. These factors, coupled with the strategic position of copper and zinc, have given impetus to the Bureau's War Research Program for the development of alloys containing nonstrategic manganese for the purpose of supplementing or providing alternates for the more strategic metals. The alloy reported here was studied, along with several other ferrous and nonferrous alloys, as possible cartridge-case material, and was chosen after a review of the properties of the ternary alloys of copper-manganese-zinc. Preliminary Work In a cursory survey of this system, alloys ranging from 60 to 95 per cent copper, o to 50 per cent manganese, and 5 to 40 per cent zinc were investigated. The alloys containing 60 per cent copper were found to fall into the two-phase alpha plus beta region of the system, and since those containing 70 per cent would not permit a saving, only alloys containing 65 per cent copper were considered. The tensile properties of these 65 per cent alloys are plotted in Fig. I as a function of manganese content for annealed material and for four conditions of cold-work In the annealed condition the increases in strength and decreases in elongation are minor up to 15 per cent manganese; beyond this, the changes become more significant. In the cold-worked condition, the first 5 to 10 per cent of manganese appears to have the greatest strengthening effect, the rate of increase dropping off as the manganese increases beyond this amount. These effects are more pronounced with moderate than with severe cold reduction. It is also interesting to note that while the elongation of annealed material drops regularly with increasing manganese, the elongation in the cold-worked state is relatively little affected by increasing manganese content, particu-

Jan 1, 1944

By J. R. Long, T. R. Graham

This report is concerned with part of a series of investigations carried on by the Federal Bureau of Mines on alloys, particularly nonferrous alloys, made with electrolytic manganese. A broad general program instituted after commercial quantities of electrolytic manganese became available was necessary in order to compare the effects of electrolytic manganese with those of the ordinary commercial grades. Representative analyses of these two materials show the commercial manganese metal to contain up to 2 per cent iron, a maximum of I per cent silicon and 0.06 per cent carbon, while the electrolytic manganese rarely exceeds 0.01 iron, 0.02 sulphur, with no silicon or aluminum. In the literature, the emphasis has been largely on high-strength casting alloys containing up to 5 per cent manganese, and few data are available on wrought manganese alloys. These factors, coupled with the strategic position of copper and zinc, have given impetus to the Bureau's War Research Program for the development of alloys containing nonstrategic manganese for the purpose of supplementing or providing alternates for the more strategic metals. The alloy reported here was studied, along with several other ferrous and nonferrous alloys, as possible cartridge-case material, and was chosen after a review of the properties of the ternary alloys of copper-manganese-zinc. Preliminary Work In a cursory survey of this system, alloys ranging from 60 to 95 per cent copper, o to 50 per cent manganese, and 5 to 40 per cent zinc were investigated. The alloys containing 60 per cent copper were found to fall into the two-phase alpha plus beta region of the system, and since those containing 70 per cent would not permit a saving, only alloys containing 65 per cent copper were considered. The tensile properties of these 65 per cent alloys are plotted in Fig. I as a function of manganese content for annealed material and for four conditions of cold-work In the annealed condition the increases in strength and decreases in elongation are minor up to 15 per cent manganese; beyond this, the changes become more significant. In the cold-worked condition, the first 5 to 10 per cent of manganese appears to have the greatest strengthening effect, the rate of increase dropping off as the manganese increases beyond this amount. These effects are more pronounced with moderate than with severe cold reduction. It is also interesting to note that while the elongation of annealed material drops regularly with increasing manganese, the elongation in the cold-worked state is relatively little affected by increasing manganese content, particu-

Jan 1, 1944

By J. E. Tiffany, S. S. Lubelsky

For blasting in coal mines the U. S. Bureau of Mines recommends that permissible explosives be used exclusively, that these shall be fired electrically, and that where feasible the working place shall be cut or sheared. These recommendations are made to promote safety and prevent mine explosions. Although permissible explosives are not flameless, their lower flame temperature and shorter duration of flanie make their use safer than that of nonpermissible explosives. Mixtures of air with both methane and bituminous coal dust, which are liable to occur in coal mines, may be ignited by coming in contact with any type of flame or spark of sufficient temperature and duration or by the firing of a blast. In a working place where a blast is to be fired, in addition to the use of permissible explosives, adequate ventilation for the dilution and removal of accumulations or outbursts of flammable gas should be provided. Bituminous coal mines should be rock-dusted as a means of rendering the coal dust harmless The efficient use of permissible explosives depends upon the proper preparation of the working place, standardized drilling, the strength characteristics of the explosive, and the use of a proper weight of charge. Experienced shotfirers should load, tamp and fire all holes. The major part of the information and data here presented is based on the results of efficiency tests made in large producing mines of Pennsylvania and Illinois. Bureau of Mines Report of Investigations, Serial No. 2697, describes how a standard method of blasting was worked out and put into operation in a mine in southern Illinois.' This paper contains a description of the methods worked out subsequently in another mine in that district. Descriptions of tests in two Pennsylvania mines are given in Bulletins 11 and 19 of the Carnegie Institute of Technology.2 These tests

Jan 1, 1928

By Maurice C. Fetzer, Charles R. Austin

It has long been known that plain high-carbon steels may be susceptible to graphiti-zation below the A1 critical, but no data have been available to indicate what factors cause and tend to inhibit graphite formation. Two recent publicationsl,2 have shown that the factors controlling graphitization below the A1 are different from those operating above the A1 inversion where commercial graphitization of malleable iron begins. Furthermore, for plain high-carbon steels graphitization below the critical point does not appear to be related to ordinary chemical analyses. Many years ago it was recorded3 that the rate of graphitization at subeutectoid temperature is not a maximum just below the A1 critical, but at some lower temperature, which Austin and Norris have shown to be about 670°C. Indeed, work done in our laboratory has demonstrated that it is impossible to spheroidize certain steels in the temperature range of 650° to 710°C. without the formation of considerable amounts of graphite. However, if the temperature is maintained just below the A1 (720°C.) these same steels may be completely sphe-roidized at constant temperature. In previous studiesl,2,4 on I per cent plain carbon steels graphitization was encountered during prolonged tempering. The limited number of steels studied did not provide sufficiellt data to permit adequate study of the factors controlling this graphitization. Accordingly, a limited statistical investigation was undertaken, utilizing 18 steels of similar chemical analyses, furnished by four steel companies, who also supplied information regarding the history of manufacture. An extensive program of research is being carried out on these steels, including the effect of pretreatment and atmosphere on the nature and extent of graphitization, and the possible correlation of graphitization with such characteristic properties as hardenability, grain size and mechanical behavior. In the present paper discussion is restricted to a study of the correlation between graphitizing tendency at 670°C. after quenching from several temperatures above the critical, and (I) the minor variations in the chemistry of these steels of "similar" chemical composition, and (2) the deoxida-tion practice employed. The state of the lead bath, oxidized or protected from oxidation by charcoal, used in the tempering treatments is also considered. Materials Eighteen plain carbon steels of about I per cent carbon, and containing similar amounts of each of the other common elements usually found as impurities, were obtained in the form of rods % in, in diameter from four steel manufacturers. The analyses for ordinary and special elements of all the steels were made on the rod stock as received in the laboratory, and the re-

Jan 1, 1941

By Maurice C. Fetzer, Charles R. Austin

It has long been known that plain high-carbon steels may be susceptible to graphiti-zation below the A1 critical, but no data have been available to indicate what factors cause and tend to inhibit graphite formation. Two recent publicationsl,2 have shown that the factors controlling graphitization below the A1 are different from those operating above the A1 inversion where commercial graphitization of malleable iron begins. Furthermore, for plain high-carbon steels graphitization below the critical point does not appear to be related to ordinary chemical analyses. Many years ago it was recorded3 that the rate of graphitization at subeutectoid temperature is not a maximum just below the A1 critical, but at some lower temperature, which Austin and Norris have shown to be about 670°C. Indeed, work done in our laboratory has demonstrated that it is impossible to spheroidize certain steels in the temperature range of 650° to 710°C. without the formation of considerable amounts of graphite. However, if the temperature is maintained just below the A1 (720°C.) these same steels may be completely sphe-roidized at constant temperature. In previous studiesl,2,4 on I per cent plain carbon steels graphitization was encountered during prolonged tempering. The limited number of steels studied did not provide sufficiellt data to permit adequate study of the factors controlling this graphitization. Accordingly, a limited statistical investigation was undertaken, utilizing 18 steels of similar chemical analyses, furnished by four steel companies, who also supplied information regarding the history of manufacture. An extensive program of research is being carried out on these steels, including the effect of pretreatment and atmosphere on the nature and extent of graphitization, and the possible correlation of graphitization with such characteristic properties as hardenability, grain size and mechanical behavior. In the present paper discussion is restricted to a study of the correlation between graphitizing tendency at 670°C. after quenching from several temperatures above the critical, and (I) the minor variations in the chemistry of these steels of "similar" chemical composition, and (2) the deoxida-tion practice employed. The state of the lead bath, oxidized or protected from oxidation by charcoal, used in the tempering treatments is also considered. Materials Eighteen plain carbon steels of about I per cent carbon, and containing similar amounts of each of the other common elements usually found as impurities, were obtained in the form of rods % in, in diameter from four steel manufacturers. The analyses for ordinary and special elements of all the steels were made on the rod stock as received in the laboratory, and the re-

Jan 1, 1941

By K. J. Miller, R. E. Hucko

The Coal Reparation Division of the Pittsburgh Mining Technology Center conducted an investigation to assess and compare the pyritic sulfur reduction potential of coal-pyrite flotation and high-gradient magnetic separation (HGMS). Tests were run on three coals - an Upper Freeport bed coal, a Lower Kittanning bed coal, and a Pittsburgh bed coal - to establish grade-recovery relationships characteristic of both processes. Representative portions of each coal sample were crushed to two top sizes-nominal - 500 pm (-35 mesh) and nominal - 149 pm (-100 mesh)-and subjected to conventional froth flotation. The froth product was then beneficiated by coal- pyrite flotation or HGMS, to provide a direct technical companion of the two processes. At - 500 pm (- 35 mesh), the size normally employed for coal flotation, both coal-pyrite flotation and HGMS effectively separated pyrite from coal, and the performance of the two processes was essentially the same. At a - 149 pm (- 100 mesh) sire, however, the performance of HGMS exceeded that of coal-pyrite flotation. The separation effected by HGMS were more efficient at - 149 pm (- 100 mesh) than at - 500 pm (- 35 mesh). On the other hand, it was concluded that either the effectiveness of coal-pyrite flotation decreases with diminishing top size or the process has not been optimized to treat material finer than 500 pm (35 mesh).

Jan 1, 1983

By Z. T. Bieniawski, E. Unal, H. Reginald Hardy

INTRODUCTION Rock bolts are a major means of support in underground coal mines in the United States. However, two of the most crucial problems facing the mining engineer today are that of finding a well defined and standard method for testing the anchoring ability of rock bolts, and of selecting the most suitable type of rock bolt and bolting pattern for a particular mine or specific mine section (Anon., 1982). Such selection requires not only an understanding of the behavior of the rock mass and the rock-bolt unit itself, but also a knowledge of the basic mechanisms by which rock bolts provide support while they interact with the rock mass during various field loading conditions. A recent study in this area has shown the inadequacy of present methods used in selecting and testing of rock bolts and the lack of clearly defined guidelines for safe and economical design of bolting patterns (Bieniawski, et al., 1980). The present paper describes a research study aimed at developing laboratory instrumentation and associated techniques for the evaluation of bolt-rock interaction. The instrumentation system developed, procedures followed during various experiments, and typical results from a series of studies carried out on mechanical bolts are presented. DEVELOPMENT OF THE ROCK BOLT TESTING FACILITY General A block diagram of the experimental facilities are shown in Fig. 1. The system consists of three main sections. The first

Jan 1, 1982

By I. A. Lesk

The various materials utilized in the construction of integrated circuits, and the resultant materials interfaces, are discussed with emphasis on a materials system that is compatible with all types of integrated circuits and minimizes the number of different interfaces. Problems with interfaces may originate in the silicon, on its surface, and between other materials within the integrated-circuit package independent of the silicon. ThE difference between integrated-circuit theory and practice may generally be spelled out in terms of the difficulties in fabricating a desired structure. There are, of course, problems in forming the requisite materials, of the necessary composition and geometry, where needed. A distinct class of problem, however, is associated with interfaces— generally between different materials, but occasionally between regions of the same material. We require that each interfacial system perform its proper electrical, mechanical, and thermal function, and do so in an unchanging manner with time under the most severe operating conditions. In a practical sense, we deal in nonideal systems, such that it is generally not possible to form an interface exactly the way it was intended, even if we allow for a knowledge of the practical limitations of the fabrication system. Another way of looking at this situation is to realize that, when we form a group of interfaces under apparently the same experimental conditions, there are often differences of important consequence between them. Very high-magnification pictures, such as are obtained by an electron microscope, reveal fine structure that often differs over the area of a given sample, as well as from sample to sample. Low-magnification pictures look better, but don't eliminate the problem. The trend towards integrated circuits, and away from circuits fabricated utilizing separate components, is very strong in many areas of electronics. A typical silicon monolithic integrated circuit, still in place in the wafer on which it was fabricated, is shown in Fig. 1. The increased reliability which is being experienced through the use of integrated circuits can, to a large extent, be credited to the reduced complexity of the interface system that is present in the electronic system. A glance at Fig. 1, however, with all of its epitaxial and diffused p-n junctions, and interconnect system, shows that interfaces have been far from eliminated. Fig. 2, depicting a schematic cross-sectional view of a (partial) typical integrated circuit, illustrates in detail the numerous interfaces that occur in this type of structure. Besides the individual circuit elements, there are interfaces for isolation, and, Fig. 3, even a crossover requires a series of interfaces. What has been accomplished, however, irrespective of whether or not the total number of interfaces in the circuit is increased or decreased, is that the variety of interfaces is very much reduced. This is because there are fewer materials involved. Since the expense incurred in an R & D program to improve reliability is pretty much directly proportional to the variety of interfaces involved, it is economically advisable to work with integrated circuits for highest reliability. That is not to say that circuits built using standard components could not be made as reliable as integrated circuits, but that the expense involved because of the more complex over-all interface system would be much greater. Although electronic performance utilizing integrated circuits with all silicon elements (i.e., transistors, diodes, resistors, capacitors) is adequate for many applications, there are numerous instances where thin-film passive elements must

Jan 1, 1965

By Philip B. Bucky

FIFTEEN papers were presented at the Monday and Tuesday joint sessions of the Industrial Minerals Division and Society of Economic Geologists, covering beryl, mica, wollastonite, magnesium resources, exploration for pegmatite mineral deposits, rutile, properties and uses of phosphates, and a general survey of nonmetallic minerals and their war uses.

Jan 1, 1944