Search Documents

By Mark Malamphy

DURING the latter part of the year 1932, the Servico Geologico e Mineralogico do Brasil ordered four magnetic field balances with tem-perature-compensated magnetic systems and a photographic recording apparatus for the registration of the diurnal variation. These instru-ments were delivered during the early part of the year 1933 and a short time later were taken to Santa Catherina for use in the field. Before the field work was begun, a series of experiments was carried out to determine the behavior of these new instruments under existing field conditions. The recording instruments were mounted in an under-ground chamber and their sensitivities checked by means of a Helmholtz coil. The field instruments were then mounted at fixed stations and readings were taken to determine the diurnal variation and compare it with the photographic records. The data obtained with the horizontal field balances were concordant but that obtained with the vertical component instruments showed a considerable divergence. This divergence was of such a magnitude that it was necessary to spend considerable time in determining its cause and finding a means of improving the functioning of the instruments. This paper presents the results of our observations on these systems and the conclusions at which we arrived; also the means we took to partly elimi-nate the difficulty until new systems could be ordered from Germany.

Jan 1, 1935

By W. J. Taylor

FURNACE-MEN who have not taken advantage of the use of dynamite in certain blast-furnace troubles, as explained by Mr. Witherbee in his valuable papers read before the Institute some years since, cannot appreciate the quick relief and great advantage that may be derived at times from its judicious employment. Before giving my experience in the use of high explosives in blastfurnace troubles of certain kinds, I will record a method I have used with marked success in " blowing down." Had I not understood, however, the use of powder, I would have " salamandered " effectually the first time I tried it. Early in my straight-furnace experiments, last summer, at the Chester, N. J., Furnace, I wanted to blow down to within 3 or 4 feet of the tuyeres. To do this with a down-comer not lined, and without putting in any limestone to keep the gases cool enough to do no harm, was not an easy task. We could keep the bell and hopper cool by filling them with water, say 12 inches deep; but before we got the stock down 15 or 20 feet the pyrometer in the gas-flue on top mas up to 1300°, and the clowncomer was red-hot, with the heat still rising. In this emergency my assistant, Mr. N. M. Langdon, urged the trial of a plan lie had often advocated, viz., the introduction of water in some way under the bell in the proper quantity, in order that its evaporation might absorb and reduce the heat of the escaping gases to a point where it would not do any harm. He thought the bell

Jan 1, 1885

AS I told you before in the treatise on ores, once these are found (whether they are ores of metals or semiminerals) it is necessary to assay them in order to know what is in them, since the judgment of the sight is not sufficient for recognizing the quantity or even what substance they contain. For this reason, it is necessary to come to assaying and, with the knowledge of experience, to weigh their virtues and to proceed with the work or withdraw from it and its expense; and also through knowledge to make provision for their defects if some evilness harms the ores. For if you should have need of a thing that would help them and should not find it, all that you have done would be lost; and, on the other hand, if you should find that the ores are abundant and rich and easy to smelt, you take courage to continue without respect for anything. Therefore, in the following book I shall tell you first in general how the assay of all the metals should be made. I shall enlarge in particular on silver more than on any of the others since it is more important. Then I shall tell you how the ores should be prepared for smelting and also how blast furnaces and other furnaces for smelting such ores should be constructed, and finally how all elemental mixtures of metals are to be separated one from the other with the ability and power of art, and how they are reduced to their final perfection and fineness according to their species.

Jan 1, 1942

By J. B. Newsom

IN the Indiana limestone district, some 50 or 60 per, cent of the merchantable stone in a quarry opening is waste, and only about 40 or 50 per cent of the stone from the opening is finally sold. So long as the present system of quarrying is used, the wastes measured and reported in this paper will continue. Comprehensive development of an entirely different method of quarrying, using wire saws for cutting, promises great improvement. Some of the savings to be expected are pointed out in the following pages. No attempt has been made to measure losses due to variations and natural flaws in the stone, since these vary greatly in different quarries, and accurate measurement would be difficult. The wastes that have been measured account for about 30 per cent of the total ledge, which leaves 20 or 30 per cent chargeable to unmeasured sources of loss.

Jan 1, 1932

By C. K. Stoddard, R. G. Knickerbocker, E. T. Leidigh, R. R. Lloyd, K. L. Mattingly

During July 1941, a study was initiated at the Boulder City Experiment Station of the Bureau of Mines on proposed methods for the production of magnesium metal. The major emphasis was placed upon development of a process that required minimum reliance upon the sale or utilization of by-products to meet economic competition from processes already in operation. It was felt that only through the development of such a process could the nation's vast resources of dolomite and low-grade magnesite that are contiguous to large blocks of firm power be properly utilized. During the course of exploratory tests on electrolytic and electrothermic processes, it was noted that fused magnesium chloride would dissolve appreciable quantities of magnesium oxide in the presence of small amounts of boric oxide. The use of such a solution in an electrolytic cell employing a graphite anode and a steel cathode caused the deposition of magnesium at the cathode and the evolution of carbon oxides at the anode with minimal amounts of chlorine The original results were sufficiently encouraging to justify further investigation on an enlarged scale, since the process seemed to present advantages over other proposed processes.1,2 for the direct use of magnesium oxide in a fused chloride electrolyte. When work oil a larger scale was initiated it was found that the addition of boric oxide to the electrolyte resulted in dispersion of metal and constantly decreasing current efficiency. However, by this time solubility studies had shown that magnesium oxide was sufficiently soluble in magnesium chloride melts containing no boric oxide to effect the same anode reactions, and development work was continued. Over two years of development work have been carried out, and considerable work remains to be done. It is desired to emphasize the fact that many of the difficulties met require a long period of continuous operation before they become serious enough to affect operation of the cell. ACKNOWLEDGMENTS This paper is one of many reporting on various aspects of the Bureau of Mines' program initiated in August 1939 by passage of the Strategic Minerals Act the scope of which was greatly expanded by subsequent legislation. Some of these papers are published as war minerals reports. others as bulletins, technical papers, reports of investigations

Jan 1, 1949

By C. K. Stoddard, R. G. Knickerbocker, E. T. Leidigh, R. R. Lloyd, K. L. Mattingly

DURING July 1941, a study was initiated at the Boulder City Experiment Station of the Bureau of Mines on proposed methods for the production of magnesium metal. The major emphasis was placed upon development of a process that required minimum reliance upon the sale or utilization of by-products to meet economic competition from processes already in operation. It was felt that only through the development of such a process could the nation's vast resources of dolomite and low-grade magnesite that are contiguous to large blocks of firm power be properly utilized. During the course of exploratory tests on electrolytic and electrothermic processes, it was noted that fused magnesium chloride would dissolve appreciable quantities of magnesium oxide in the presence of small amounts of boric oxide. The use of such a solution in an electrolytic cell employing a graphite anode and a steel cathode caused the deposition of magnesium at the cathode and the evolution of carbon oxides at the anode with minimal amounts of chlorine The original results were sufficiently encouraging to justify further investigation on an enlarged scale, since the process seemed to present advantages over other proposed processes 1.2 for the direct use of magnesium oxide in a fused chloride electrolyte. When work on a larger scale was initiated it was found that the addition of boric oxide to the electrolyte resulted in dispersion of metal and constantly decreasing current efficiency. However, by this time solubility studies had shown that magnesium oxide was sufficiently soluble in magnesium chloride melts containing no boric oxide to effect the same anode reactions, and development work was continued. Over two years of development work have been carried out, and considerable work remains to be done. It is desired to emphasize the fact that many of the difficulties met require a long period of continuous operation before they become serious enough to affect operation of the cell. ACKNOWLEDGMENTS This paper is one of many reporting on various aspects of the Bureau of Mines' program initiated in August 1939 by passage of the Strategic Minerals Act the scope of which was greatly expanded by subsequent legislation. Some of these papers are published as war minerals reports. others as bulletins, technical papers, reports of investigations

Jan 1, 1945

By John F. Abel

The following quotation is from "Guidelines for evaluation of undergraduate curricula in geological engineering, mineral processing, and mining engineering" prepared by the Committee on Education of SME of AIME. "The objectives of the Engineers' Council for Professional Development (ECPD), as delineated in its constitution, are: (a) To promote and advance all phases of engineering education with a view to the promotion of the public welfare through the development of the better educated engineer and engineering technician." (Italics added.) The problem is that no one has as yet seriously developed a method of supplying engineering technicians. There were great hopes that the expansion of junior colleges would help satisfy this need. Sadly, they have not; and it appears they are unwilling or unable to supply the need for mineral engineering technologists. Apparently, the junior colleges cannot afford staff for such courses, even when the colleges are located in mining districts.

Jan 1, 1971

By AIME AIME

MANY years ago when the writer chaperoned a group of student officers from Wright Field on their re- quired inspection trip through the Mid- dletown plant of American Rolling Mil1 Co., Leo Reinartz was our guide. After the party had watched continuous strip being rolled and was ready to move on we ventured a remark-to emphasize the difference between Armco iron and automobile fender stock-that this strip was ordinary steel. The remark was overheard by our guide and the effect was instantaneous; in a rather re- proachful tone Leo said: "Gentlemen, your teacher has been in this plant many times, and he should know by now that we, in this company, never make ordinary steel-all of our prod- ucts are the highest possible quality."

Jan 1, 1943

By J. D. Lubahn, R. P. Carreker, J. G. Leschen

The formation of slip bands in crystalline solids undergoing plastic deformation has recently been treated as a problem of nu-cleation and growth.' A simplified theory was developed and shown to be qualitatively consistent with certain experimental observations reported in the literature, such as the frequent failure of slip bands to traverse the entire crystal, the effect of specimen diameter and temperature on the yield stress, and the occurrence of incubation periods in the deformation of suddenly loaded crystals. The theory further predicts the appearance of transients in the rate of strain of a crystal when the applied stress is suddenly changed from one constant value to another. A transient consists of a discontinuous change in the strain rate followed by a gradual approach to a steady-state value. Such transient behavior apparently has not been recognized in previous experimental work. The preliminary experiments reported in the present paper were undertaken to confirm the existence of the predicted transients and thus to determine whether a more detailed treatment of the nucleation theory of slip might be theoretically and experimentally fruitful. Experimental Procedure A simple creep apparatus was assembled as shown in Fig I. Very little insulation was used on the furnace in order to facilitate rapid changes of temperature. Temperature was measured with a thermometer placed in the center of the furnace and was controlled by adjusting the Variac setting. The specimens were cold-headed in split-cylinder grips. The strain was measured as total elongation by a dial gauge sensitive to I/I0,000-in movement of the weight pan. Since the specimen gauge lengths were

Jan 1, 1949

By J. D. Lubahn, R. P. Carreker, J. G. Leschen

THE formation of slip bands in crystalline solids undergoing plastic deformation has recently been treated as a problem of nucleation and growth.1 A simplified theory was developed and shown to be qualitatively consistent with certain experimental observations reported in the literature, such as the frequent failure of slip bands to traverse the entire crystal, the effect of specimen diameter and temperature on the yield stress, and the occurrence of incubation periods in the deformation of suddenly loaded crystals. The theory further predicts the appearance of transients in the rate of strain of a crystal when the applied stress is suddenly changed from one constant value to another. A transient consists of a discontinuous change in the strain rate followed by a gradual approach to a steady-state value. Such transient behavior apparently has not been recognized in previous experimental work. The preliminary experiments reported in the present paper were undertaken to confirm the existence of the predicted transients and thus to determine whether a more detailed treatment of the nucleation theory of slip might be theoretically and experimentally fruitful. EXPERIMENTAL PROCEDURE A simple creep apparatus was assembled as shown in Fig 1. Very little insulation was used on the furnace in order to facilitate rapid changes of temperature. Temperature was measured with a thermometer placed in the center of the furnace and was [ ] controlled by adjusting the Variac setting. The specimens were cold-headed in split-cylinder grips. The strain was measured as total elongation by a dial gauge sensitive to 1/10,000-in. movement of the weight pan. Since the specimen gauge lengths were

Jan 1, 1948

By J. J. Mike

During the past few years the combination of continuous billet casting with in-line reduction has been studied and several machines have been built with this capability included in the design parameters. (1,2,3,4,5) In-line reduction and continuous casting in combination are obvious and attractive. As pinch rolls are already in place for the continuous casting operation, it can be readily seen that a redesign of the mechanical and electrical equipment of the pinch rolls is all that is necessary to have in-line rolling. There have been numerous in-line reduction experiments conducted by simply increasing the pinch roll pressure on existing machines. (6,7,8,9) These generally failed to produce quality billets and often resulted in internal metallurgical defects (Figure 1).

Jan 1, 1972

By Y. Nakada, U. F. Kocks, B. Chalrners

THE orientation dependence of work hardening has previously been studied over the entire range, i.e., including special orientations of high symmetry, in aluminum1-3 and silver.* The differences between various orientations are substantial, and the trend is the same in all fcc crystals. However, there are quantitative differences in behavior between aluminum and silver at room temperature, particularly in the (100) orientation. While many experiments on gold have been reported,5'9 none included the special orientations. We therefore undertook tension tests on gold crystals of the axial orientations (100),(110), (Ill), (211), and, as a representative of single slip, one whose Schmid factor was 0.5 (hereafter referred to as m = 0.5). Single crystals of dimensions 1/4 by .1/4 by 6 in. were grown from the melt1' at a rate of 4 in. per hr, using gold of 99.99 pct purity obtained from Handy and Harman. A growth rate of 1/8 in. per hr, or a purity of 99.999 pct,ll produced no difference in results. The crystals were annealed at 1000°C in air for 24 hr and furnace-cooled down to room temperature, after which they were electro-polished in a solution of potassium cyanide (40 g), potassium ferrocyanide (10 g), soda (20 g), and enough distilled water to make 1 liter of solution, at a current density of 0.02 amp per sq mm. After 2 or 3 hr, a very smooth surface was obtained by this method. Nine m = 0.5, two (loo), one (110), three (Ill), and one (211; crystals were tested at room temperature in a floor-model Instron machine at a tensile strain rate of 0.5 pct per min. The accuracy of the stress measurement was k10 g per sq mm up to 500 g per sq mm, k2 pct for higher stresses. The strain measurement was accurate to t2 pct. The scatter of stress at a given strain among the crystals of the same orientation was small, *5 pct being the largest. The representative stress-strain curves for various orientations are shown in Fig. 1. Table I summarizes the work-hardening parameters as used by seeger.12 Results of other investigators are also included in this table for comparison. There are no previous data for the corner orientations. Values for m = 0.5 crystals agree fairly well with those of Berner. Tm is defined as the stress at which the stress-strain curve begins to deviate from linearity of Stage 11. However, in practice this is a very difficult value to estimate because each investigator has a different idea of linearity. Therefore, the comparison with the values of other investigators may not be valid. In the present experiment, (100) crystals had the highest 111, followed by (111) crystals. The work-hardening rate in Stage I1 was highest for the (111) crystal followed by the (100) crystals. Our value for 0x1 of m = 0.5 orientation agrees very well with those of other investigators. 1) Single-Slip orientation (m = 0.5). These crystals were oriented so that the primary-slip vector was contained in one side face. The dimension perpendicular to this side should then not change if single slip indeed takes place. Within the accuracy of measurement, this dimension did not change during the deformation. Since the accuracy is k0.2 pct, the amount of secondary slip is less than 0.7 pct of the slip on the primary-slip system at 30 pct tensile strain. This is in conformity with the results obtained by Kocks" for aluminum crystals. The tensile axis moved toward (211) during the deformation. Slip bands, Fig. 2(a), were very fine and closely spaced. Some deformation bands were observed. There were no clear-cut cross-slip traces such as the ones observed on aluminum m = 0.5 crystals. 2) (111) Crystals. The orientation of the tensile axis was stable during the deformation. From this observation, one can deduce that at least three slip systems must have operated, and probably all six because the remaining three all have cross-slip relation to one of the first three.' It was very difficult to observe the slip markings. Consequently, we could not confirm by this method that six systems were operative during the deformation. At high strains (above 50 pct shear strain), this orientation had the highest stress-strain curve. At 80

Jan 1, 1964

By W. T. Bishop

For many years pine oil has been used extensively as a frother for the flotation of minerals, particularly sulphides, yet the published information available to the average user on its composition, chemical and physical properties, has been rather meager. It is the purpose of this paper to discuss these points and their relationship to the frothing properties of pine oil used in flotation processes. Pine oil, as the name implies, is a liquid obtained from the processing of wood of the longleaf and other southern pines. It is a complex mixture of naturally occurring terpene derivatives, primarily alcohols, and a smaller amount of terpenes, which has found many uses in various industries. Its use as a frother in flotation processes was the first large-scale application in industry and today the mining industry still consumes large quantities of pine oil but the textile and disinfectant industries consume comparable volumes. Much is used in soap manufacture and laundry operations. The surface-active properties of pine oil are in a large degree responsible for this versatility. History The name "Naval Stores" goes back to the days when pine tar and pitch were used to caulk leaky ships and 'Oat their ropes and rigging. Today this term is still used to include not only the oleoresinous products of the pine tree—rosin and turpentine— but other products such as pine oil, pine tar, and the many terpene and resinous compounds obtained by extracting the pine wood or tapping the tree. That part of the industry known as "wood naval stores" dates from about the beginning of this century and today produces a large part of the country's rosin and turpentine by processing pine wood. In addition, all of our natural pine oil is supplied by the wood naval stores industry, as tapping of the live tree gives only rosin and turpentine. This latter phase is known as the "gum naval stores " industry. The first successful commercial operation of the steam and solvent process of the wood naval stores in industry was carried out by Yaryan at Cadillac, Mich., in 1909.1 This operation did not prove profitable, so Yaryan went south to utilize the longleaf pine, and built a plant at Gulfport, Miss.2 Soon after, another plant was built at Brunswick, Ga., which is still in operation, and in 1914 was reported to have processed about 500 tons of wood per day.' In 1921 Hercules Powder Co. acquired the Yaryan interests, at which time the production of pine oil was only 3 to 5 million pounds per year and flotation was the largest customer. As time went on, technological advances were made, other companies entered the field, and the production of pine oil increased many fold. The growth of the industry was especially marked during the past 10 years, and in

Jan 1, 1947

By W. T. Bishop

For many years pine oil has been used extensively as a frother for the flotation of minerals, particularly sulphides, yet the published information available to the average user on its composition, chemical and physical properties, has been rather meager. It is the purpose of this paper to discuss these points and their relationship to the frothing properties of pine oil used in flotation processes. Pine oil, as the name implies, is a liquid obtained from the processing of wood of the longleaf and other southern pines. It is a complex mixture of naturally occurring terpene derivatives, primarily alcohols, and a smaller amount of terpenes, which has found many uses in various industries. Its use as a frother in flotation processes was the first large-scale application in industry and today the mining industry still consumes large quantities of pine oil but the textile and disinfectant industries consume comparable volumes. Much is used in soap manufacture and laundry operations. The surface-active properties of pine oil are in a large degree responsible for this versatility. History The name "Naval Stores" goes back to the days when pine tar and pitch were used to caulk leaky ships and 'Oat their ropes and rigging. Today this term is still used to include not only the oleoresinous products of the pine tree—rosin and turpentine— but other products such as pine oil, pine tar, and the many terpene and resinous compounds obtained by extracting the pine wood or tapping the tree. That part of the industry known as "wood naval stores" dates from about the beginning of this century and today produces a large part of the country's rosin and turpentine by processing pine wood. In addition, all of our natural pine oil is supplied by the wood naval stores industry, as tapping of the live tree gives only rosin and turpentine. This latter phase is known as the "gum naval stores " industry. The first successful commercial operation of the steam and solvent process of the wood naval stores in industry was carried out by Yaryan at Cadillac, Mich., in 1909.1 This operation did not prove profitable, so Yaryan went south to utilize the longleaf pine, and built a plant at Gulfport, Miss.2 Soon after, another plant was built at Brunswick, Ga., which is still in operation, and in 1914 was reported to have processed about 500 tons of wood per day.' In 1921 Hercules Powder Co. acquired the Yaryan interests, at which time the production of pine oil was only 3 to 5 million pounds per year and flotation was the largest customer. As time went on, technological advances were made, other companies entered the field, and the production of pine oil increased many fold. The growth of the industry was especially marked during the past 10 years, and in

Jan 1, 1947

By R. J. Charles

F. C. Bond: This is an outstanding paper on comminution theory and represents a considerable advance in mathematical formulation. It clears the way for a discussion that should ultimately decide whether the work index should be considered as a parameter according to the Third Theory or as a constant. In the empirical differential equation dE = —Cdx/x [1] either Corn must be treated as a variable to satisfy known crushing and grinding conditions. The author has chosen the exponent n as the variable, with C as a constant. According to the Third Theory, in the general case n is a constant equal to 3/2, and C is a variable related to the work index Wi. If x is placed equal to P (the size in microns which 80 pct of the product passes) and F is the size 80 pct of the feed passes, then C equals 5 W1, and dE = 5 -5 Widx/x = 10 Wi 10 Wi w = vP vF which is the basic equation of the Third Theory. It is apparent that this integration involves the error of treating the parameter Wi as a constant, just as the author's treatment involves the error of integrating his variable n as a constant. These errors are probably relatively unimportant, considering the small range of the variables. When more is known about the factors contained in the work index, Eq. 1 can be revised as a partial differential equation. The Third Theory exponent of 1/2, or n = 3/2 in the Charles' differential equation (Eq. l), was not chosen primarily because it is the average between the Kick and Rittinger exponents; this may be merely fortuitous, since it is illogical to define truth as the average between two errors. It was first discovered from the study of a large mass of crushing and grinding data and confirmed by laboratory testing. The general correspondence of the Third Theory equation to actual crushing and grinding results over the entire size reduction range argues strongly that a fundamental phenomenon is involved. The a posteriori theoretical explanation of the constant Third Theory exponent is that the work done in breaking rock is proportional to the length of the crack tips formed. Compressive force applied to the rock results in deformation and strain energy. When this locally exceeds the breaking strength a crack tip forms, the surrounding strain energy flows to the crack tip and extends it to split the rock, with release of the energy as heat. Under rapid impact the crack tip may form before the strain has reached equilibrium, resulting in less energy expenditure and probably a coarser product. In any case, the elastic limit of a brittle material is practically the same as its breaking strength, and the work necessary to form the crack tip is the work required to break. The crack length of a ton of broken rock cannot be measured directly. However, the particle shapes of feed and product are similar, and the crack length is considered equal to the square root of one half of the new surface area formed. It is, therefore, proportional to 1/vD, where D is the equivalent product particle diameter. This is the basis of the Third Theory equation. Many secondary factors can be imposed upon the crack length breakage. These may cause the Third Theory work index to increase or decrease somewhat as the product size becomes finer. The work index is properly a parameter rather than a constant, making it an increasingly valuable practical criterion of the work input required in crushing and grinding.

Jan 1, 1959

By J. A. Reeves

The unit-train for moving mineral raw materials is considered by many railroad men as the most significant contribution toward reducing rail freight costs since the introduction of the diesel locomotive. The idea, which involves assigning railroad equipment to only one haul and keeping the equipment rolling, results in the maximum utilization of equipment. For example, before the unit train was placed in service on coal hauled to one of Mid-Continent Coal and Coke Company's customers, about 900 cars and 9 locomotives were needed to move its coal requirements, compared with 250 cars and 6 locomotives currently used. If unit-train economics are to be achieved, coal companies cannot use railroad cars as small storage bins on wheels to accumulate their coal in train-load shipments, instead, these companies must build large bins which incorporate facilities for the rapid loading of railroad cars in a minimum length of time.

Jan 1, 1970

By Harold B. Treweek

The development of full scale flotation circuits based on laboratory and/or pilot plant data is discussed. Auxilliary operations, equipment and layout essential for trouble-free start-up and operation are noted. The selection of flotation cell size is discussed as it affects plant capital and operation costs.

Jan 1, 1978

By T. M. Morris

The forces acting between a small rod, one end of which was made water repellent, adhering to a much larger air bubble in water were measured. An equation is deduced which correlates these forces and the influence of each force is discussed. The importance of the size of bubbles in a flotation cell is emphasized.

Jan 1, 1950

Downtime cannot be tolerated on electric shovels whose cost may approach or exceed $400,000 each. The same may be said for larger-variety off-highway trucks which require an operational expenditure upwards of $50 per hour. One company, for instance, in order to ensure a more continuous operation, has specified centralized lubrication for all of its new equipment. In wet or dry weather, the mining of asbestos can place undue strains on machinery and other equipment. When the mineral is dry, its dusty, loose fibers work their way into crevices, and when wet, the glutinous asbestos may adhere to axles, gears and other wear components. Such conditions are multiplied during the extreme cold winters of eastern Canada. It is more difficult to lubricate and maintain equipment, and erosiveness becomes more punishing to wear parts. Resultant breakdowns rapidly drain off profits.

Jan 1, 1971

By John Birkinbine

A RETROSPECT of the growth of the production of pig-iron for the past half century would be the history of the invention and introduction of heated blast as applied to the smelting of iron ores. As the apparatus employed was improved in conception and construction, the economical operation of the furnaces to which it was attached was the more marked, and the production correspondingly increased. To compare the original iron box placed over a coal fire with the modern hot-blast stove, with its combustion-chamber, gas-burners, and air-regulators, would be as unfavorable to the former as to contrast the product of the little Blauöfen with the yield of the improved furnaces of to-day. But, as these little Blauöfen were the germs from which the larger plants have grown, so from the crude apparatus invented and applied by Neilson has grown, in the face of great opposition, the more economical hot-blast stoves now in use. It is not surprising that an innovation like heated blast should have received a large amount of attention from metallurgists, nor that men of recognized ability should formerly have been found both among its champions and opponents, but it is remarkable that, at the present day, with the results of careful research and thorough experiment compiled in convenient shape for perusal, there are iron¬masters who still consider it economy to allow the products of combustion to escape into the atmosphere, rather than utilize them in heating the blast, because of a supposed injury to the quality of the product. In the present state of knowledge and practice, it is proper to express as an axiom, that a well-constructed hot-blast apparatus is essential to the economic operation of an iron-producing plant. Of the interpretation of proper construction there is of necessity a variety of opinions, and, with the view of solving the problem, the apparatus for heating blast has from time to time assumed various forms. Boxes, cylinders, and pipes, placed horizontally, vertically, inclined, or in circles and spirals, have been tried ; there have been pistol-shaped pipes, double pipes, divided or diaphragm pipes, siphon pipes, and as much variety in the mains, connections, flues, and setting. It is probable that, to the introduction of the bell and hopper in

Jan 1, 1876