Search Documents

By D. Harker, M. J. Murphy

THE mechanism by which age-hardening takes place is still not completely understood. The principal theories range from the extreme of "precipitation-hardening" to that of "order-hardening," with many intermediate gradations. In the hope of obtaining new data on which to base a choice among the many theories, the authors have made electron micrographs of formvar replicas taken from metallic specimens at various stages of age-hardening. The results so obtained on an alloy of 2 per cent beryllium in copper and one of 20 per cent molybdenum in iron will be described in the following pages, as well as the technique used in preparing the replicas. PREPARATION OF FORMVAR REPLICAS OF METALLIC SPECIMENS This section is concerned with the techniques that have proved successful in preparing formvar replicas for studying the microstructure of metals with the electron microscope. Because of its simplicity and accuracy, the formvar replica1 method developed in the General Electric Research Laboratory has been used exclusively, since it is much simpler than the silica replica method of Heidenreich and Peck2 and produces as good results. The formvar method to be described requires a technique acquired only by practice, and no foolproof set of rules can be given. It is a rapid method and a replica can be obtained in less than five minutes under favorable conditions. This does not mean that perfect replicas can be produced every five minutes, but rather that one can well afford to take several strippings* in order to produce a replica of high quality. The metallographic technique required for replica work-very fine polishing and etching with very dilute solutions-is described here. It can be said, in general, that almost any surface that has been carefully prepared for a photomicrograph at 1000 or more diameters can be used to obtain a replica for the electron microscope. PREPARATION OF METALLOGRAPHIC SPECIMENS The preparation of the metallographic specimens is somewhat more exacting than that usually given to samples to be used for inspection under the light microscope. After much experimentation, it was concluded that the best method consists in polishing the metal through to the coarse cloth, then etching and repolishing on final cloth until the layer of distorted metal is removed. After this procedure has been completed, a dilute etch-to approximately the depth necessary for a micrograph at 1000 diameters-usually produces a sur-

Jan 1, 1945

By E. Swartzman, G. C. Behnke

THE free-swelling index, a numerical value for the free-swelling properties of coal, is being used to an increasing extent in specifying coal for burning in various types of equipment. The empirical standard ASTM method for determining this index uses, as a source of heat, a gas burner which requires frequent calibration because gas pressures are not constant, relatively small changes in gas pressure resulting in rather wide variations in the temperature attained in a crucible and thus in the resultant size of the coke button. Furthermore, the quartz crucibles specified for the test are not standard equipment, and relatively small variations in dimension and wall thickness from those specified often result in rather wide variations in the resultant size of the button. A method of analysis to be satisfactory not only for a scientific laboratory but also for use in industrial control laboratories under varying conditions should employ equipment which is rugged, easily calibrated, and readily replaceable by standard materials. Gas is not universally available as is electricity, and it is generally easier to calibrate and control a simple electric furnace or heater than a gas burner, the voltage not usually fluctuating to the degree that gas pressure does. Quartz crucibles are fragile, and the size specified in the test is not normally used for any other purpose in the laboratory. Although more expensive, the 15-cc platinum crucible, available in all laboratories where volatile matter in coal is determined by the standard ASTM method, is sturdy and standard and easily replaced. Because of these considerations, a modification of the standard method has been developed which employs a standard laboratory 350-w cone heater and standard 15-cc platinum crucibles. The results of numerous tests conducted with such apparatus show conclusively that the free-swelling index values as judged by the buttons produced with this equipment are exactly the same as those obtained by the standard gas burner method. Thus it is suggested that this electric cone heater method employing standard 15-cc platinum crucibles be considered as an alternative to the ASTM method, Designation: D720-46. The free-swelling index of coal is determined by means of the ASTM method, D720-46. This method, which is an adaptation of the crucible swelling test for coal of the British Standards Institution, consists of heating 1 g of coal in a special covered quartz crucible in a regulated gas flame for a period of not less than 2.5 min in which time the temperature of the inner surface of the bottom of the crucible reaches a temperature of 82025°C. The residual coke button is then compared in size and shape with a series of standard profiles shown in Fig. 1 and designated by number from 1 to 9 in increasing order of size. As the method is empirical, it requires rigid standardization of the apparatus and repeated calibration of the gas burner. The dimensions of the low form quartz crucible recommended must be rigidly adhered to as small variations in diameter or wall thickness result in variations in the rate of heat transmission and thus in the resultant size and shape of the coke button. The gas burner must be calibrated almost every time a new set of determina-

Jan 1, 1952

By Corliss R. Kinney

SINCE the first atomic bomb exploded over Japan, a great deal of speculation has been published about the use of atomic energy instead of coal for the production of power. Atomic energy, in time, may displace coal for this purpose, but atomic energy will not displace coal in supplying chemical raw materials to the rapidly expanding carbon-chemicals market. Modern civilization demands large quantities of carbon compounds and the logical source of many of these is coal. Consequently, many progressive operators are considering the possibilities of the utilization of coal as a chemical raw material as never before. Furthermore, the demand for clean, smokeless, and ashless fuels will continue to increase and the only way to handle coal under those conditions is to take it apart, just as crude petroleum is taken apart. One can readily imagine where the petroleum industry would be now if it had insisted on selling customers only crude oil, perhaps emulsified with a little salt water to correspond to the moisture and mineral matter in raw coal. The time seems to be coming at an accelerated pace when mine operators will find that competing for a highly selective fuel market by producing a larger tonnage at smaller cost will be less profitable than to increase the value of a smaller tonnage many fold by producing something more valuable to industry and civilization than raw coal. For example, about 750,000 tons of carbon black selling for $50 to $60 per ton was produced in the United States in 1945. This tonnage is insignificant compared with the total production of coal in the United States, but a very tidy tonnage, together with the coal necessary to operate the process, for any mine operator fortunate enough to obtain a method of producing a better carbon black from coal. From the point of view of tonnage, the manufacture of coke of various kinds and its by-products is at present the most important source of carbon chemicals from coal. Nearly 20 per cent of the coal mined in this country is used for this purpose. A large proportion of the coke is used for the production of iron and steel, but even in this operation a considerable part of the coke is used for a chemical purpose; that is, the reduction of the ore to metallic iron. In addition, large quantities of coke are used in manufacturing many important products that find their way into the market. POSSIBILITIES OF ACETYLENE One of the important chemicals manufactured from coke is calcium carbide, from which many products are made. One of these is acetylene. This hydrocarbon can also be manufactured from natural gas or from waste oil-refinery gas and' these industries will probably offer competition for the manufacture of acetylene. Coke-oven gas can be used for making acetylene and should receive consideration

Jan 1, 1946

THE paper on "Cross-cuts in Coal Mining," by J. J. Rutledge (published in MINING AND METAL-LURGY, February, 1927, p. 64) was brought up for discussion at the annual meeting, where the follow-ing comments were made T. D. Thomas (Lehigh Coal & Navigation Co., Lansford, Pa.) : This question has caused me a lot of worry, not in the particular district in which I am, but throughout other districts. There are always several angles to consider. If you are in a hurry to push development work, you might increase the distance between cross-cuts from 60 to 350 ft., but if you have a 40-ft. chain pillar every 60 ft. it will cut down your entry driving a whole lot. Looking at it from the ventilation angle, I agree that too many cross-cuts in entries are bad things. You have a tremendous amount of leakage, and I have seen currents starting out with 45,000 cu. ft., and after passing about 30 or 40 cross-cuts the current has dwindled down to about 18,000 or 15;000 cu. ft. The result is that the question of putting in auxiliary fans is raised. That involves several points into which I do not want to go too far, but I am in favor of not getting in too many cross-cuts, putting them in only where they are necessary: I think the state mining laws are wrong in a number of places on that, and that when you finish with a cross-cut it should be in the room. It should be well sealed on an entry. There are several ways of tightening up the cross-cuts so as not to have the great amount of leakage and wastage of: air that we now have. 'I prefer tile stopping; other people prefer cement or brick, but there is a big fac-tor to all mines, saving the mine. I checked up on the number of fans in the anthracite region and found there are 651. That was derived from the state report of 1921, and it enabled me to compute from the power the weight of the air. In the anthracite region of Pennsylvania we put in 9 tons of air to every ton of coal we get out. Tracing that back again and taking the Government's figures which they made some time ago, I found but 20 per cent of the air got to the faces where it was actually needed. That is a tremendous big loss and shows a possibility for saving, money for the various coal companies. Chairman Rice: I think what Mr. Thomas refers to was an investigation by R. Y. Williams, of the Bureau of Mines in Illinois, where a study was made of 100 typical mines, and, speaking off-hand, my recollection is that we found as little as 15 per cent of air reached the faces in one of the mines and another was as much as 50. That seems to be a reflection on the type of stoppings and general ventilation scheme.

Jan 3, 1927

By W. E. Horst

During the past few years of operation at Kings Mountain, N. C., full-scale flotation has generally yielded poorer metallurgical results than those obtained in the laboratory or pilot plant. After 2 min in each size of Denver flotation machine in the spodumene rougher circuit, pilot recovery (41.7 pct) was almost three times that of the plant (13.6 pet) and about twice that of the laboratory (21.0 pet). Pilot and commercial plant data are based on continuous operation, and laboratory results on batch testing of rougher performance. The ore is a pegmatite containing spodumene, feldspar, quartz, mica, and amphibolite. Data were accumulated to evaluate the scale-up relationships between laboratory, pilot plant, and plant flotation cells. Flotation rate constants and dimensional analysis were used to define the relationship existing between flotation behavior and scale of operation.

Jan 11, 1958

By Corliss R. Kinney

Since the first atomic bomb exploded over Japan, a great deal of speculation has been published about the use of atomic energy instead of coal for the production of power. Atomic energy, in time, may displace coal for this purpose, but atomic energy will not displace coal in supplying chemical raw materials to the rapidly expanding carbon-chemicals market. Modern civilization demands large quantities of carbon compounds and the logical source of many of these is coal. Consequently, many progressive operators are considering the possibilities of the utilization of coal as a chemical raw material as never before. Furthermore, the demand for clean, smokeless, and ashless fuels will continue to increase and the only way to handle coal under those conditions is to take it apart, just as crude petroleum is taken apart. One can readily imagine where the petroleum industry would be now if it had insisted on selling customers only crude oil, perhaps emulsified with a little salt water to correspond to the moisture and mineral matter in raw coal. The time seems to be coming at an accelerated Dace when mine operators will find that competing for a highly selective fuel market by producing a larger tonnage at smaller cost will be less profitable than to increase the value of a smaller tonnage many fold by producing something more valuable to industry and civilization than raw coal. For example, about 750,000 tons of carbon black selling for $50 to $60 per ton was produced in the United States in 1945. This tonnage is insignificant compared with the total production of coal in the United States, but a very tidy tonnage, together with the coal necessary to operate the process, for any mine operator fortunate enough to obtain a method of producing a better carbon black from coal. From the point of view of tonnage, the manufacture of coke of various kinds and its by-products is at present the most important source of carbon chemicals from coal. Nearly 20 per cent of the coal mined in this country is used for this purpose. A large proportion of the coke is used for the production of iron and steel, but even in this operation a considerable part of the coke is used for a chemical purpose; that is, the reduction of the ore to metallic iron. In addition, large quantities of coke are used in manufacturing many important products that find their way into the market. Possibilities of Acetylene One of the important chemicals manufactured from coke is calcium carbide, from which many products are made. One of these is acetylene. This hydrocarbon can also be manufactured from natural gas or from waste oil-refinery gas and these industries will probably offer competition for the manufacture of acetylene. Coke-oven gas can be used for making acetylene and should receive consideration

Jan 1, 1947

By Corliss R. Kinney

Since the first atomic bomb exploded over Japan, a great deal of speculation has been published about the use of atomic energy instead of coal for the production of power. Atomic energy, in time, may displace coal for this purpose, but atomic energy will not displace coal in supplying chemical raw materials to the rapidly expanding carbon-chemicals market. Modern civilization demands large quantities of carbon compounds and the logical source of many of these is coal. Consequently, many progressive operators are considering the possibilities of the utilization of coal as a chemical raw material as never before. Furthermore, the demand for clean, smokeless, and ashless fuels will continue to increase and the only way to handle coal under those conditions is to take it apart, just as crude petroleum is taken apart. One can readily imagine where the petroleum industry would be now if it had insisted on selling customers only crude oil, perhaps emulsified with a little salt water to correspond to the moisture and mineral matter in raw coal. The time seems to be coming at an accelerated Dace when mine operators will find that competing for a highly selective fuel market by producing a larger tonnage at smaller cost will be less profitable than to increase the value of a smaller tonnage many fold by producing something more valuable to industry and civilization than raw coal. For example, about 750,000 tons of carbon black selling for $50 to $60 per ton was produced in the United States in 1945. This tonnage is insignificant compared with the total production of coal in the United States, but a very tidy tonnage, together with the coal necessary to operate the process, for any mine operator fortunate enough to obtain a method of producing a better carbon black from coal. From the point of view of tonnage, the manufacture of coke of various kinds and its by-products is at present the most important source of carbon chemicals from coal. Nearly 20 per cent of the coal mined in this country is used for this purpose. A large proportion of the coke is used for the production of iron and steel, but even in this operation a considerable part of the coke is used for a chemical purpose; that is, the reduction of the ore to metallic iron. In addition, large quantities of coke are used in manufacturing many important products that find their way into the market. Possibilities of Acetylene One of the important chemicals manufactured from coke is calcium carbide, from which many products are made. One of these is acetylene. This hydrocarbon can also be manufactured from natural gas or from waste oil-refinery gas and these industries will probably offer competition for the manufacture of acetylene. Coke-oven gas can be used for making acetylene and should receive consideration

Jan 1, 1947

By H. Tabachnick, N. Hedley

The extraction of gold and silver from ores with alkaline cyanide solutions is well known. Cyanide solutions are also good solvents for many base metal minerals, particularly most of the copper minerals. Leaver and Woolf,1 who determined the solubilities of copper minerals in 0.10 pct sodium cyanide solution, showed that malachite, cuprite, chalcocite, and bornite are readily soluble in cyanide; least soluble are chalcopyrite and chrysocolla. The Mining Chemicals Laboratory of American Cyanamid Co. has studied the possibilities of using cyanide solutions for leaching base metals. In this article the authors present the results of their experiments with cyanide leaching to reduce the copper content of a zinc concentrate from 0.050 pct to the desired specification of less than 0.02 pct. Zinc Ore Sample: The sample of commercial zinc ore used in this investigation to produce zinc concentrates was ball mill feed ranging from 1/2 in. to fines. The ore was crushed to —10 mesh and riffled into 600-g charges for zinc flotation. Analysis revealed 4.54 pct Zn and 0.005 pct Cu. Examined microscopically, the ore consisted essentially of cream-colored sphalerite and carbonate gangue. It contained a small amount of pyrite, partly tarnished. The only copper mineral identified was chalcopyrite, mostly smaller than 20µ, some of which occurred as attachments on sphalerite. Flotation Procedure: Batches of zinc concentrates were made as required according to the following general procedure. A 600-g charge of —10 mesh ore was ground for 4 min at 60 pct solids in a laboratory steel rod mill. Screen sizing showed it to be all —35 mesh with 42 pct —200 mesh. The pulp was transferred to a Fagergren laboratory flotation machine, diluted to 25 pct solids and conditioned for 5 min with 0.6 lb per ton CuSO4, . -5H2O. It was then conditioned with 0.10 lb per ton Sodium Aerofloat promoter and floated for 5 min with pine oil as frother and creosote as froth stiff-ener. The pH during flotation was 8.5. A typical analysis of zinc concentrate subjected to leaching is 44.41 pct Zn and 0.051 pct Cu. The ratio of concentration was close to 10 to 1. Leaching Procedure: Aero Brand cyanide, technical calcium cyanide analyzing 49.5 pet NaCN equivalent, was used for all cyanide leaching tests. For each test three rougher concentrates floated as described were combined (total weight close to 180 g) and the water content adjusted to 150 ml. The percent solids in the pulp was thus 55. After a weighed amount of cyanide flakes had been added, the pulp was agitated on rolls for a given period, then filtered and washed. Filtrate and washed concentrate were assayed for copper content. The procedure for ammonia leaching was similar to the cyanide process. A series of tests was run in which the effects of ammonia as a solvent for copper in the zinc rougher concentrate were investigated. In each test 180 g of zinc rougher concentrate was leached with 150 ml of ammonia solution. Various strengths of ammonia and times of leaching were investigated. The results are shown in Table I. It is apparent that ammonia was a poor solvent for copper in the zinc concentrate; 60 min of agitation with a relatively strong NH:, solution extracted only 2 pct of the copper. CYANIDE LEACHING TESTS Effect of Solution Strength: The solvent effects of 0.125, 0.187, and 0.250 pct NaCN equivalent solutions were compared for leaching periods of 15 min. Residue and filtrate were assayed for copper content. The copper content of the filtrate plus wash was calculated back to the original volume of cyanide solution (150 ml). The effects of cyanide strength are given in Table II, It will be noted that 15 min leaching with 0.25 pct NaCN equivalent solution extracted 74.6 pct of the copper in the zinc concentrate. The leached product assayed 0.013 pct Cu, appreciably below the required specification of 0.020 pct. Effect of Leaching Time: Portions of zinc concentrate were leached with 0.25 pct NaCN equivalent

Jan 1, 1961

By C. C. Nathan

Data are resented on the physical properties of five waxes obtained from fields in Texas and Louisiana in which "parafin" troubles are being experienced. The crude parafin was fractionated into three components, voluble in cold acetone, soluble in boiling acetone, and insoluble in boiling acetone. The acetone insoluble fraction was found to consist essentially of straight chain parafin hydrocarbons in the molecular weight range 525 to 700. Solubilities of the purified high molecular weight parafins were determined in a number of solvents. It was found that in hydrocarbon solvents, including crude oil, solubilities could be calculated satisfactorily by use of ideal solubility relations. In chlorinated, and oxygenated solvents, large deviations from ideal behavior were observed. These deviations could be partially correlated with the internal pressure of the solvent. INTRODUCTION A problem encountered in many producing oil fields is that of "paraffin" deposition. The problem refers to the deposition of material from the crude oil onto tubing, pumping rods, flow lines, or other material contacted by the crude. This problem has been recognized for nearly a hundred years, and numerous investigations have been reported on its causes and prevention or alleviation. One of the more comprehensive of such investigations was published by Reistle1 in 1932. A few of the salient findings of his report are briefly as follows: The term "paraffin" as used to describe this problem refers to the deposit of carbonaceous material which is not soluble or dispersible by the crude oil under the conditions where deposition occurs. The "paraffin" normally consists of high molecular weight paraffin hydrocarbons, both straight chain and branched, resins and asphaltic materials of undetermined nature, occluded oil and water, and possibly sand. In consistency, the deposit may vary from a soft, sticky material, to one which is hard and brittle. Deposits are usually black, although lighter colors are sometimes observed. Under the conditions of temperature, pressure, and crude oil composition occurring in the underground reservoir, the paraffin is in suspension or solution in the crude. As the oil flows to the surface, there is generally a reduction of temperature, pressure, and the amount of dissolved gases contained in the oil. Reduction of temperature and gas break-out were shown by Reistle to be factors causing reduced solubility of the paraffin in the crude. Thus, as the crude containing paraffin rises to the surface and flows to storage tanks at atmospheric temperature, the solubility of the paraffin may be exceeded. Deposition will begin at the point in the system where the temperature of the system falls below its cloud point, and continue as long as there is a further drop in the solution power of the crude for the paraffin. The severity of the deposition as well as the location of the bulk of the deposition, i.e., in subsurface or surface equipment, will depend on the amount of paraffin originally in the crude, the manner in which pressure and temperature of the crude

Jan 1, 1956

By Donald L. Katz

FIFTEEN years ago Dr. Manning published a paper in "Petroleum Development and Technology" on '.Fundamental Research Relating to Petroleum." He tabulated for several industries "the proportion of their present success which can be fairly attributed to the application of information and processes obtained by scientific research," giving petroleum a score of 7 compared to 100 for the electrical and coal-tar industries. Today the petroleum industry as a whole and the producing groups both have raised their score beyond the majority and are climbing toward the top. Present practices are being developed both by fundamental research and the application of the research method in field operation.

Jan 1, 1941

By Bruno V. Nordberg

The high cost of coal in Butte and the development of large amounts of cheap electric power from the Missouri river caused the Anaconda Copper Mining Co. in 1908 to make an investigation as to the possibility of adapt- ing this cheap electric power for the operation of their many large hoisting plants. At this time electric power had already been adopted for practically all other power purposes around the mines, such as pumping, compressing air, etc. The map (Fig. 1) shows the location of the mines of the Butte mining district. These mines are located within a circle of approximately a 1-mile

Jan 1, 1914

By H. R. MacMichael

THE rate, at which zinc ore can be sintered varies widely, depending on the characteristics- of the ore. A coarse table concentrate already roasted to a very, low sulfur content may sinter at the rate of-8.6 tons per hour per 100 sq.ft., of wind-box area. At the other extreme is a finely ground flotation, concentrate, with considerable sulfur remaining in the ore as delivered to the sinter plant, for which corresponding rate may be only 3.8 tons per hour, or 44 per cent of the first rate. A usual, size-of sinter machine in zinc plants is one with wind-box 3.5 by 33 ft., making 115.5 sq. ft. of area, and using a 100-hp. fan. Such a machine with the coarse concentrate described would produce 10 tons of sinter per hour; and with the fine, flotation concentrate would produce only 4.4 tons per hour. Ore of the latter class is -sintered at the plant of the Mexican Zinc Co. (subsidiary of the American Smelting & Refining Co.) at Rosita, Mexico. ; Consequently, an unusually large sintering capacity per ton of ore to be treated is required, and provision was made for treatment of 9000 tons concentrates per month, preroasted to. 5 to 9 per. cent sulfur. For this duty three of the usual 33-ft., 100-hp. sintering machines would have been needed.. Considering the auxiliary equipment. necessary for proportioning, handling, and mixing charge, as well as means for disposition of the sinter, a three-unit plant becomes-very complicated, especially if the capacity should be doubled later. After much study it was decided to build a single sintering unit of ample capacity for the work, the plant thus being much simpler and cheaper in construction as well as in operation (Figs. 1 and 2). The sintering machine was built with a wind-box 5.25 by 60 ft. (315 sq. ft.) and provided with a 300-hp. fan.

Jan 1, 1932

By Robert R. French

Beneficiation of low-grade nonmetalliferous mineral deposits by electronic color sorting is currently undergoing a period of rapid development. For those deposits in which the specific gravity, strength, soundness, and electric and magnetic properties of the ore and gangue are similar, the possibility of separation by color, reflectivity, or fluorescence offers hope for the utilization of much poorer quality ore than previously thought possible. For those ores in which consistency of color is required or for which a dry process is preferred, the electronic color sorter is particularly adaptable. Tests performed late in 1966 and reported herein are the result of continued interest in the dry beneficiation of gypsum and the development of higher capacity color-sorting machines. These tests should be considered only as an indication of the efficiency of the process and only with respect to the low-grade, untreated ore tested. Although most of the ore mined in Martin County, Ind., is of acceptable quality, a few thin carbonate strata and irregular nodules of dolomite and limestone are present within the main evaporite bed (Fig. 1).

Jan 1, 1969

By L. F. Elkins

In 1946 Littlefield, Gray and Godbold published a thorough geologic description of the West Edmond Hunton Lime reservoir, located in Central Oklahoma, and discussion of its early performance.l They stressed implications of the nature of the reservoir rock on performance to be expected with production both by natural means and by pressure maintenance with gas injection. The essence of their analysis was that presence of an extensive interconnected system of fractures and solution channels constituting about 10 percent of the total reservoir void space in otherwise very low permeability reservoir rock would result in severe channeling of naturally encroaching water or injected gas through the fractures with little or no benefit to ultimate recovery of oil. Considerations were in progress to unitize the reservoir for pressure maintenance by gas injection. Some other engineers involved in the project had considerably different opinions at the time regarding continuity of fractures and regarding effects of such fractures on performance. The field was unitized Oct. 1, 1947. Subsequently, pilot gas injection tests were conducted in four areas of the field; large scale waterflooding was conducted in two parts of the field in the Bois d'Arc or Upper Hunton; and pilot waterflooding was conducted in the Chimney Hill or Lower Hunton. Full scale water-flooding is now in progress in the Chimney Hill section where it is oil productive. The primary purpose of this paper is to divine some of the secrets of this reservoir through analysis of all aspects of its performance, with the hope that it will be of help to engineers and operators in developing and operating other low permeability fractured reservoirs. In part, this considers variance of actual performance from some widely used conventional reservoir engineering assumptions. For brevity, other aspects of unit operation and its benefits to the owners are not discussed. Oil and Gas in Place For unit participation, net pay in the Bois #Arc defined by the gross SP anomaly on electric logs totalled 2,100,000 acre-ft in the 30,000-acre reservoir. Development of West Edmond predated modem logging techniques that now would be used to determine "net" or "productive" pay. In Fig. 1 this log pick is compared with detailed core analysis and core descripfion by Littlefield et a1.l for one well identified as A on the index map in Fig. 2. Not all of the gross Bois #Arc section had oil staining, but all cores with measureable intergranular permeability were stained. (The committee selection of the Bois d'Arc SP interval also includes the Frisco section as identified from cores by Littlefield.) The Bois d'Arc is oil productive throughout the entire 600-ft monoclinal accumulation from the eastern upstructure erosional pinchout to the west-side oil-water contact. (See Littlefield et al.l and McGee and Jenkins for geologic detail.)

Jan 1, 1970

By R. H. B. Jones

This paper reviews pertinent geology of the Biwabik iron formation, Mesabi Range, Minnesota. This iron formation is divisible into four members. Each member is distinctive and contains marker horizons, which are recog nizable throughout all phases of alteration from lean, fresh rock to high-grade iron ore. Some beds have a larger magnetite content than others. During the process of ore genesis, which is essentially an oxidation process, the magnetite content is lowered. Alteration from iron formation to ore includes both oxidation of iron minerals and silica removal by leaching and these distinct processes progress at variable rates for different locations and structures. Magnetic intensities, of each horizon of the iron formation are dependent chiefly upon its preoxidation magnetite content, upon the subsequent degree of oxidation, upon the character of the enclosing rocks, and on the extent of fracturing, folding, or faulting. The results of a number of magnetic surveys are described and are correlated with results of drill-hole and mine exploration and developmerit. The magnetic anomalies obtained are discussed in relation to phases of formation of ore within the iron formation. General Information One hundred years ago a party of surveyors, applying the principles of geophysical prospecting, discovered iron ore in the state of Michigan in the Lake Superior district. This event was officially reported as follows:' On Sept. 19 (1844) while running the east line of Town 47 North, Range 27 West, they observed by means of the solar compass remarkable variations in the direction of the needle, amounting to 87" from the normal. Ascribing this phenomenon to iron ore, they sought and found it in ledges or outcrops at several points. The solar compass referred to was invented by William A. Burt, deputy surveyor in charge of this party.2 It is used for determining the true meridian by an observation on the sun. Eight years later, on July 7, 1852, the first iron 're, consisting of 6 bbl. of Ore, was shipped from Marquette, Michigan. It was another 40 years before the first or> shipment left the Mesabi Range in Minnesota, in October 1892. It totaled 4245 tons. Fifty years later, 90 years after the original shipment, during 1942 the Lake Superior district shipped 93,495,392 gross tons of iron ore. Production came from Minnesota, Michigan, Wisconsin, and Ontario, Canada. Throughout the 90-Year period it was known that magnetic properties of most of the ore bodies, and of the iron formations in which they occur, affected the compass. This phenomenon, later to be made use of to outline areas of ground favorable for exploration, was at first a

Jan 1, 1949

By R. H. B. Jones

This paper reviews pertinent geology of the Biwabik iron formation, Mesabi Range, Minnesota. This iron formation is divisible into four members. Each member is distinctive and contains marker horizons, which are recog nizable throughout all phases of alteration from lean, fresh rock to high-grade iron ore. Some beds have a larger magnetite content than others. During the process of ore genesis, which is essentially an oxidation process, the magnetite content is lowered. Alteration from iron formation to ore includes both oxidation of iron minerals and silica removal by leaching and these distinct processes progress at variable rates for different locations and structures. Magnetic intensities, of each horizon of the iron formation are dependent chiefly upon its preoxidation magnetite content, upon the subsequent degree of oxidation, upon the character of the enclosing rocks, and on the extent of fracturing, folding, or faulting. The results of a number of magnetic surveys are described and are correlated with results of drill-hole and mine exploration and developmerit. The magnetic anomalies obtained are discussed in relation to phases of formation of ore within the iron formation. General Information One hundred years ago a party of surveyors, applying the principles of geophysical prospecting, discovered iron ore in the state of Michigan in the Lake Superior district. This event was officially reported as follows:' On Sept. 19 (1844) while running the east line of Town 47 North, Range 27 West, they observed by means of the solar compass remarkable variations in the direction of the needle, amounting to 87" from the normal. Ascribing this phenomenon to iron ore, they sought and found it in ledges or outcrops at several points. The solar compass referred to was invented by William A. Burt, deputy surveyor in charge of this party.2 It is used for determining the true meridian by an observation on the sun. Eight years later, on July 7, 1852, the first iron 're, consisting of 6 bbl. of Ore, was shipped from Marquette, Michigan. It was another 40 years before the first or> shipment left the Mesabi Range in Minnesota, in October 1892. It totaled 4245 tons. Fifty years later, 90 years after the original shipment, during 1942 the Lake Superior district shipped 93,495,392 gross tons of iron ore. Production came from Minnesota, Michigan, Wisconsin, and Ontario, Canada. Throughout the 90-Year period it was known that magnetic properties of most of the ore bodies, and of the iron formations in which they occur, affected the compass. This phenomenon, later to be made use of to outline areas of ground favorable for exploration, was at first a

Jan 1, 1949

By S. M. Parmley

Experience has shown that there are some factors connected with the drying of fine washed coal that are not present in drying of slack coal as normally practiced at cement kilns or pulverized coal plants. It is the purpose of this paper to show some of these variations as they have been encountered under actual operation. The Champion No. 1 cleaning plant of the Pittsburgh Coal Co. uses the wet system of cleaning coal. The plant is equipped to produce commercial sizes or mixtures, the primary sizes being plus 6 in. and 4 by 6 in., which are hand-picked. Minus 4-in. sizes are all cleaned by the wet process. To produce a commercial product as free of moisture as possible, the washed coal is first passed over sizing and dewatering screens, then each size except the — ?-in. coal is conveyed to loading booms by slow-moving draining conveyors. As the +?-in. sizes are not heat-dried, no data will be given, as it is the purpose of this paper to describe the heat drying of — ?-in. coal as practiced at the Champion No. 1 plant of the Pittsburgh Coal Company. To fully appreciate the conditions, it must be remembered that the — ?-in. product is now shipped at a lower moisture content than when received from the mine. The incoming coal in the — ?-in. size will average 5 per cent. moisture and the shipped product 3 per cent. moisture. This is a case where a wet process gives a reduction of both ash and moisture in the fine sizes. The shipped product, therefore, is more uniform in all characteristics, and uniformity of product is the most important single factor in coal preparation. The 0 by ?-in. coal is first dewatered on slow-moving continuous bucket dewatering elevators, running at the rate of 40 ft. per minute, with 48-in. perforated buckets with ¼ by 1½-in. slots, spaced ? by 2?-in. centers staggered. The moisture in the coal discharged from the elevators runs 20 to 28 per cent., depending on the fineness of the product. The discharge from the dewatering elevator is further drained on a drag-type conveyor equipped with ½-mm. wedge wire screen. The conveyor discharges coal with an 18 to 25 per cent. moisture to three centrifugal dryers of the Carpenter type. The Carpenter dryers

Jan 1, 1931

The University of North Dakota, State Geological Survey, Grand Forks, N. D A G. Leonard, State Geologist. Two publications of the State Geological Survey are of interest Fourth Biennial Report, The clays and clay industries of North Dakota, and Bulletin 4, Lignite deposits and lignite industries of North Dakota. Bulletin 11 of the University is of interest: Geology and natural resources of North Dakota For further information, address the above

Jan 1, 1933

ALTHOUGH the refining period of the heat is generally defined as A starting after the charge has been completely melted, it may more properly be considered as beginning with the first efforts to facilitate the shaping up of the slag and the making of corrective additions for the control of slag or metal composition. Such actions may be initiated during the latter half of the lime boil. The early part of the refining period may, then, in essence overlap the latter part of the melting period. The primary aims of the refining period are to reduce phosphorus and sulphur from the steel bath to levels safely below the maximum contents specified, to eliminate carbon as rapidly as possible and still allow time for proper conditioning of the slag and attainment of the necessary bath temperature, and to deliver the heat ready for tapping or furnace deoxidation, with slag in the proper physical and chemical condition, and with carbon and oxygen contents and the temperature of the steer bath at the proper levels for the composition and grade of steel being produced. The particular conditions that fulfil these aims are distinctly different, depending upon whether the steel is to be finished according to fully-killed, semikilled, or rimming practice and also depending upon the carbon range specified. Regard- less of the type of charging practice employed, the object of the refining period is to produce repeatedly the desired finishing and tapping conditions for the grade of steel being produced. The variations and proportions of raw materials used in the charge may cause some variations in the degree of control required during refining, but not in the method of control. The refining period can therefore be discussed from a viewpoint largely independent of charging and melting practice. SHAPING UP THE SLAG In the first helper's vocabulary, refining practice consists in "shaping up" his heat. This includes elimination of sulphur, phosphorus, and carbon, putting the slag in proper condition, and adjusting bath temperature. Shaping up the slag is a major consideration because

Jan 1, 1944

By John W. Vanderwilt

THE fluorescence of scheelite has been an important aid in recent years in the discovery and development of scheelite deposits. The use of fluorescence of synthetic compounds in industry, particularly in advertising, also has expanded greatly during the past decade. As a result, a number of new and convenient units for producing ultraviolet energy have become available, which have led to a greater application of fluorescence in the study of minerals. Studies have shown that the fluorescent color of a mineral may vary: (I) with the kind and quantity of trace elements, and (2) with the particular wave length of ultraviolet energy used. The wave length is dependent first on the type of generating equipment used, and finally on the filter employed to remove the visible light that may be present. A number of so-called ultraviolet lamps are listed and described, together with suitable filters known to be available. Scheelite fluoresces brilliantly with wave lengths of 2200 to about 3000Å., but not with longer wave lengths. The most convenient and efficient sources of ultraviolet for scheelite fluorescence- are portable and laboratory units designed particularly for use with scheelite. So-called ultraviolet light globes of the photo-flood type emit wave lengths too long to cause scheelite to fluoresce. Attention is called to the minerals that fluoresce in a manner similar to scheelite, which necessitates a check test by means of characteristic physical properties. Chemical tests are the final authority both for identity and content of tungsten in scheelite ore.

Jan 1, 1946