Search Documents

By W. A. Backofen, G. Y. Chin, W. F. Hosford

The effect of machine stiffness on discontinuous flow and fracture of the 2024 aluminum alloy was studied in tension at 4.2OK. An increase of machine stiffness was found to decrease the amount of elongation and drop in load during discontinuous flow, thereby postponing fracture to larger strains and higher stresses. The possibility of utilizing stiffened tools in deformation processing to suppress shear fracture originating from unstable flow was indicated. The problem of nucleating discontinuous flow and the role of the effective mass of the system in discontinuous flow were also considered. AT low temperatures the plastic flow of metals is often discontinuous, with sudden load drops and elongations.1,3 Basinski1,4 has presented strong evidence that discontinuous flow, at least in aluminum alloys, occurs under nearly adiabatic conditions. During testing the load may drop suddenly and flow become localized when the thermal softening, due to heat generated in plastic straining, is greater than the strain and strain-rate hardening. This instability criterion is more easily satisfied at low temperatures because 1) the volume specific heat is reduced so that relatively large temperature increases are possible in straining, and 2) the flow stress is relatively temperature-dependent. The important role of adiabatic shear in ductile fracture processes has been emphasized,5-1 and consideration has already been given to the influences of thermal and mechanical properties on the tendency of a material to undergo adiabatic shear.17677 By focusing attention on how the mechanical loading system influences low-temperature discontinuous flow, additional insight into adiabatic shear and its effect on fracture may be gained. EXPERIMENTAL PROCEDURE Because of its low thermal conductivity, the 2024 aluminum alloy exhibits a highly consistent discon- tinuous-flow behavior at 4.2°K and was therefore chosen as the material for study. Machined specimens of 0.113 in. diam and 1.125 in. gage length were solution heat-treated at 490°C for 3 hr, quenched into cold water, and immediately immersed in liquid nitrogen until just before testing. Testing was done at 4.2°K by immersion in liquid helium at a crosshead drive rate of 0.03 in. per min. As normally used (hard-machine basis), the spring constant of the testing machine was k = 25,000 lb per in. By inserting beam springs in series with the specimen, this value could be lowered by a factor of about 100. Details can be found elsewhere.? As a result of variable machine stiffness, the actual strain rate ranged from about 3 x 10 5 to 3 x 10-4 per sec from one test to another, as well as within any one test. However, preliminary tests had established that the tensile curves were not altered significantly by this strain-rate variation. Fig. 1 shows a typical load vs plastic-elongation curve for a solution heat-treated 2024 aluminum alloy specimen pulled in the standard hard machine (k = 25,000 lb per in.) at 4.2"K. The elastic extension has been subtracted. Plastic flow proceeded smoothly from yielding at approximately 22,000 psi (load = 220 lb) to a strain of about 4 pct at which point the flow became discontinuous. The magnitude of the load drops as well as the plastic elongation per drop increased with increasing strain until the specimen finally broke abruptly. The load-elongation behavior of a sample tested with a relatively soft machine under otherwise identical conditions is given in Fig. 2. In general, there

Jan 1, 1964

By Richard Rice

TURBO blowers for blast-furnace blowing have now been in use for some years, and a review of the experience gained and the present state of progress may be interesting. FIG. 1.-STEAM TURBINE DIRECT CONNECTED TO AIR COMPRESSOR. The first blast-furnace blowing engine of this type to be installed in America was built by the General Electric Co. and is installed at the oxford Furnace of the Empire Iron & Steel Co. This machine was put into operation March 8, 191.0. A duplicate unit is situated at the furnace of the Northern Iron Co. at Port Henry, N. Y., which unit was put into opera ion June 30, 1910 (Fig. 1).

Jan 5, 1914

W: 0. HOTCHKISS, Madison, Wis. (written discussion*).-Mr. George's paper on. "The Wisconsin Zinc District" is a very complete and clear description, which it is a pleasure to read. His discussion of the origin of the ores is the least satisfactory part, and Mr. George correctly states present knowledge when he begins his paragraph on a origin with the words "the general supposition is, etc." There is still much to be learned regarding the details of the processes by which the ores have reached their present situation. In this the Wisconsin district differs not at all from other mining districts. It is my hope that Mr. George and others, equally clear-thinking, who are in close touch with these operations will be able at an early date to give us more information on this subject.

Jan 3, 1918

By D. Havlena, A. S. Odeh

The use of the straight-line method of solving the material balance equation is illustrated by means of six field cases. Also, the application of statistical criteria to arrive at the most probable answer is shown. The theory underlying the straight-line method of solution and the applicability of the statistical criteria was presented in a previous paper.' The field cases include saturated and undersaturated oil reservoirs with and without water drive. The aquifers discussed are: limited radial, infinite radial, very small aquifer and infinite linear. The field cases also include a gas reservoir producing under water drive. INTRODUCTION In a previous paper,' the authors presented the theory underlying the solution of the material balance as an equation of a straight line. The appropriate equations for various material balance cases as well as the methods of analysis and interpretation with comments and discussion were also included. To illustrate the various theoretical cases treated previously, five field cases are analyzed in this paper by employing the straight-line method of solving the material balance equation (MBE) and one example previously published is referred to. The use of statistical criteria to arrive at the most probable answer is also shown. All the field examples presented, except Case 2, are excerpts from complete reservoir studies. To illustrate the method, only sections specifically dealing with the material balance principles are included. Additional geologic information and basic data are reported to better acquire an understanding of the cases and thus to better follow the reasoning that suggested the successful application of the straight-line method of solving the MBE. The six cases are: (1) saturated reservoir, small gas cap, limited aquifer; (2) saturated reservoir, very small gas cap, infinite aquifer; (3) undersaturated-saturated reservoir, very small aquifer; (4) highly undersaturated reservoir, no water drive; (5) high undersaturated one-well reservoir, limited aquifer; and (6) gas reservoir, infinite linear aquifer. THE D4 SAND, GUICO FIELD, VENEZUELA The D, sand, which was discovered in 1943, is presently in a depleted state. Since its discovery it has produced under water drive, gas-cap-gas expansion, and solution gas drive. In Nov., 1947, water injection was initiated to arrest further pressure decline. When discovered, the D, sand was a saturated reservoir with a gas cap /oil zone volume ratio m estimated volu-metrically at 0.0731, an average permeability of 500 md, a porosity value of 25 per cent, and an oil viscosity at reservoir conditions of 0.3 cp. The volumetrically determined stock-tank oil initially in place was 23.1 million bbl. The volumetrically weighted physical data and production data available until Nov., 1953 are reported in Table 1. In Ref. 1, the effects on the straight-line plot of various values of ro/r for a constant ?to, or of various dimen-sionless times for a constant r8/r10 were theorized and were illustrated in Fig. 3A of that reference. In this field case, the previously theoretically predicted effects are established. Thus, the MBE calculations using Eq. 3c of Ref. 1 were performed for various r6/r10 and dimension-less time values. Eq. 3c of Ref. 1 is:

Jan 1, 1965

By AIME AIME

EVEN in the choice of his birthplace and parents, Donald B. Gillies indicated clearly the trend of his professional career. He was born on Nov. 4, 1872, at Bruce Mines, in Ontario. His father and mother came from the Isle of Skye, Scotland, to Nova Scotia, moved from there to Canada, and finally settled in the copper country in the northern peninsula of Michigan, where the senior Mr. Gillies followed mining as an occupation. Donald's early education was in the public schools and he graduated from Linden Lake (Mich.) high school in 1890. Following the family interest in mining he entered the Michigan Mining School, now Michigan College of Mining and Technology. There he was the rare student who excelled both in athletics and scholastic work. On the athletic field he was a crack football player and track roan. As early as 1890 lie established a record of 10 sec-

Jan 1, 1938

By R. J. Watson, A. H. Juch

About half a million sucker-rod pumps are installed in oil wells in the U. S. alone. In Venezuela, too, the system is widely used; some 5,000, or 90 percent, of Cia. Shell de Venezuela's wells produce a total of 400,000 BOPD by this method. Most of the crude pumped is viscous, gassy and contains relatively small amounts of free water. API gravities vary from 90 to 16O; dead oil viscosities vary from 10 to 10,000 cp at the pump; and GOR's range from 100 to 2,000 cu ft/bbl. Pumps are set at depths ranging from a few hundred to 6,000 ft; the average setting depth is about 2,500 ft. From the literature, it appears that although recent years have seen significant progress toward understanding the rod pumping system as a whole, relatively little attention has been paid to those key items, the sucker-rod pump and the subsurface gas separator or gas anchor. Perhaps because of proration in the U. S., pump manufacturers have seemingly concerned themselves more with the durability of their product, achieved mainly through robust design and metallurgical know-how, than with its working efficiency. In 1963, CSV commenced a major rehabilitation and expansion of its heavy oil fields along the Bolivar Coast. The advent of the more efficient gravel-packed completion and of large-scale thermal recovery (mainly steam soak) operations resulted in well potentials *Now with B. I. P. M., The Hague, The Netherlands. greater than pump capacities. Hence, an urgent need arose to improve over-all pump efficiencies and to attack those special problems related to the production of both the extremely viscous and the hot, steam-laden crudes that formed an increasing proportion of the total stream. There followed a detailed investigation and testing program, carried out in close cooperation with a major pump manufacturer. This culminated in the introduction to the oil industry of a new line of sucker-rod pumps. Early Investigations and Experiments Field Tests Extensive field tests were carried out in three primary Bolivar Coast wells with an in-situ dead oil viscosity ranging from 400 to 6,000 cp. In these installations provision was made to (1) monitor bottom-hole pressures below, in and above the pump by means of pressure transducers, and record casing- and tubing-head pressures continuously; (2) measure accurately the annulus gas, as well as measure the tubing gas and liquid production from the well; (3) take special PVT samples of the well fluid; (4) measure power consumption of the prime mover; and (5) measure the rod loads at the polished rod. A typical test installation is illustrated in Fig. 1. It was established from the pressure transducers that with viscous oils, there is considerable flow resistance across the pump and gas anchor assembly. Pressure surges were observed over each pump cycle,

Jan 1, 1970

By C. L. Meyers, J. L. Lytton, T. E. Tietz

The recovery of tensile flow stress of 99.995-pct Al and Al-1 pct Mg alloy was investigated using a fractional recovery parameter. Tensile strainirg was conducted at room temperature, and recovery treatments were made in the range from 80° to 200°C. Equal values of fractional flow stress recovery were found to result in equivalent structural states. Identical recovery treatments were found to produce constant values of fractional flow stress re covery, independent of prestrain. The activation energy for recovery of the 99.995-pct A1 between 80" and 200°C was found to be 23,000 +2000 cal per mole, and the activation energy for the Al-1 pct Mg alloy was 27,500 cal per mole. 1 HE degree of recovery of a cold-worked metal may be studied by measuring the changes which take place in any of a number of properties. Some of the properties which have been used by past investigators include X-ray diffraction phenomena, electrical resistivity, hardness, creep strength, elastic limit, and flow stress. Despite the apparent preponderance of such studies, little is known concerning the effect of recovery on the strength of metals except as deduced from changes in various types of hardness measurements. Furthermore, little information is avail- able concerning the effects which specific solute atoms have on the recovery process. Limited studies have indicated that in some cases solid-solution additions greatly decrease the rate of recovery,' whereas in at least the case of magnesium additions to alluminum an increase in the rate has been reported.2 The purpose of this investigation was to determine the effect of a 1 pct Mg addition on the recovery of high-purity aluminum. Because of the particular interest in the effect of solute additions on the recovery behavior as related to mechanical properties, the degree of recovery was evaluated in terms of tensile flow stress. For the purposes of this study, a recovery process shall be defined as any process, short of recrystallization, whereby the properties, of work-hardened metals tend toward their values ill the unstrained state. EXPERIMENTAL PROCEDURE Test Materials. The materials used in this study were a 99.995-3 A1 and an Al-1 pct Mg alloy made from high-purity base metal. The high-purity aluminum contained the following wt pct impurities: 0.001 pct Cu, 0.002 pct Fe, 0.001 pct Si, and 0.0004 pct Mg. The Pil-1 pct Mg alloy contained 0.001 pct Cu, 0.002 pct Fe, 0.003 pct Si, and 0.99 pct Mg. Both materials were obtained in the form of as-rolled 0.125-in.-thick sheets, from the Alcoa Research Laboratories, New Kensington, Penn. Tensile specimens were cut from these sheets with the longitudinal axis in the rolling direction. Both materials were recrystallized in a molten salt bath; the high-purity aluminum at 450° C for 20 min and

Jan 1, 1962

By R. S. Kinasevich, D. D. Crabtree, D. W. Fuerstenau, T. P. Meloy, A. L. Mular

The effect of such variables as feed size, particle shape, cleavage, and hardness on the relative proportion of impact, abrasion, and chipping events in a tumbling mill is demonstrated. The concept of an average event, which is a combination of the three comminution mechanisms, is introduced. It is postulated that the average event in a particular mill determines not only the size distribution but also the energy-size reduction relationship for the comminution process. Fragmentation of particles in tumbling mills appears to result from a combination of impact, abrasion, and chipping grinding.' The relative rates of size reduction attributable to any of the basic grinding mechanisms must depend upon a number of variables, such as feed size, particle shape, hardness, and the number and kind of particles in the mill. The purpose of this paper is to show experimentally how these variables in the properties of materials affect the size distributions obtained by grinding the material's in a laboratory tumbling mill. The resulting size distributions will be intetpreted in terms of a combination of three comminution mechanisms. METHODS AND MATERIALS In this study, minerals of widely differing properties were ground either separately or as mixtures in laboratory mills using rods or balls for grinding media. The materials used include quartz, Tuolomne, limestone (99.8% CaCO3), barite, corundum, galena, pyrite, glass beads, and crushed glass. The mill used was 8 in. in diam. and 9-1/4 in. long. For the ball milling tests, 17.6 kg of steel balls (36: 7/8 in. balls, 178: 1 in. balls, and 44: 1-1/8 to 1-1/4 in. balls) were used. For the rod milling experiments, 17.6 kg of steel rods 9-1/16 in. long (25: 5/8 in., 10: 3/4 in., and 5: 7/8 in. in diam.) were used. In each test, 1 kg of solids were ground wet at 60% solids at 77 rpm. In all cases except where otherwise specified, the feed to the mill was 4 x 8 mesh material. Size distributions of the ground products were determined by a wet-dry sieving procedure with Tyler series sieves. Size distributions of mixed products containing limestone were determined by dissolving the limestone with acid and sizing the residue. EXPERIMENTAL RESULTS AND DISCUSSION If the size distribution of the product from a tumbling mill depends upon the relative proportion of impact and attrition (abrasion and chipping) events, altering the grinding conditions may change these proportions and consequently alter the size distribution of the product. Data to illustrate this point can be taken from Gaudin's classic 1926 paper.2 In one series of experiments, Gaudin ground quartz of different initial sizes for four hours in a laboratory ball mill with 7/8-in. balls. In Fig. 1, his data are reproduced as the cumulative fraction finer than the stated size for the following initial feed sizes: 13.3 x 9.4 mm, 6.7 x 4.7 mm, 2.6 x 1.6 mm, and 0.83 x 0.59 mm. As the feed size was decreased, a dramatic change in the shape of the size distribution curves took place, even though the amount of minus 100-mesh

Jan 1, 1964

By G. R. Fitterer

Trends in slag composition in acid open hearth practice, particularly the variation in iron and manganese oxides during refining, are reviewed. A procedure which is currently being used to control the refining reactions is described and partially explained through slag phase diagram considerations. In addition, the ionic nature of these slags is considered and it is proposed that silica combines with the oxide ion and forms a series of complex silicate ions. The effect of basic oxides such as FeO, MnO, and CaO is apparently additive in furnishing the oxide ion for this purpose. IT is now possible to control192 the refining of steel in an acid open hearth furnace to a surprising degree. This control has been brought about through the knowledge and use of several facts and tests. These are: 1—A planned charge analysis based on a knowledge of the type of fuel, the bath depth, etc. 2—Knowledge and control of rate of fuel input as well as its method of atomization, if any. 3—Determination of the slag fluidity. 4—Bath temperatures (use of the Pt-Pt-Rh thermocouple). 5—Periodic determination of carbon content (use of the Carb-analyzer or Carbometer). Through the use of these control methods, a heat may be made to "melt-in" with or without residual manganese and silicon. The rate of refining or carbon elimination may be controlled accurately, and the desired tapping (or "go-ahead") carbon may be approached at a rapid or slow rate according to preference and type of steel being made. Thus operating time may be predetermined and greatly reduced. Further, all of the refining can be done without any ore or other oxidizing additions, and the heat may be brought to the desired tapping temperature simultaneously with the attainment of the desired carbon analysis. This control procedure is being used in most acid plants in the United States today and has been de- scribed.', ' Although the slag metal relations are sufficiently well known to control the heat as stated, yet it is possible to account for only about two-thirds' of the 0, which must have been used for the elimination of the carbon and other metalloids. Phase diagram studies' of the slags, slag weights, the metal particle theory,' ore additions, limestone additions, etc., may all be taken into consideration; yet, the mechanism of oxidation and source of all the oxygen remain to be explained. This paper reviews some of the principles upon which the control methods were based and proposes other possibilities regarding the unexplained phenomena. Old and New Acid Open Hearth Practice Some of the recent statements in the literature regarding acid open hearth operation are based on old heat data which are not typical of modern American practice. These old heat logs have been responsible for many misconceptions regarding the acid hearth practice and represent heats which do not coincide with modern methods. In recent years, American practice has been altered materially and these changes will be briefly described. Modern American Practice: A typical log of a modern American acid open hearth heat' is shown in Fig. 1 which indicates that the refining time was only two hours, during which the carbon was eliminated rapidly and the bath temperature increased at a fast rate. The manganese and silicon contents of the metal were essentially eliminated and their oxides had become constituent parts of the slag at the "melt-down" period. During the course of the heat, the MnO content of the slag remained practi-

Jan 1, 1954

By T. P. Chen, F. W. Bowdish

Studies made with a captive bubble apparatus on the sulfidization and collection by amyl xanthate of true chrysocolla specimens have defined the ranges of pH value and sulfide concentration which permit contact between the bubble and the mineral surface. Titanium compounds were the most effective of the materials found to activate the sulfidization of chrysocolla. With titanium activation, the contact angles and the ranges of pH value and sulfide wncentration giving bubble contact were all increased. Chrysocolla ores were concentrated by flotation. Chrysocolla ores occur at many localities in grade and quantity sufficient to make mining and millin feasible, but no satisfactory method of concentratio has been found. Although chrysocolla may be leached with acid, only those ores without acid-consuming gangue may be leached economically. Because of its potential importance, a study of the conditions nece sary for flotation of chrysocolla has been carried ou The literature contains a few references to flotation of chrysocolla. Two methods were developed by the U. S. Bureau of Mines.1,2 The first consisted of a fatty acid soap and a high xanthate as collectors of chrysocolla from a synthetic ore, while the second involved the use of hydrogen sulfide and xanthate. Ludt and DeWitt3 demonstrated the difference in adsorptive powers of chrysocolla and quartz for bas triphenyl methane dyes and suggested the use of butyl, hexyl or octyl-substituted malachite green as collector. Jackel4 emphasized the effects of combin tions of reagents such as Aerofloat 31, pine oil, and Reagents 404 and 425 with sodium sulfide and zinc hydrosulfite as conditioning agents. Although he reported recoveries of 89% from a synthetic ore and 98% from a natural ore containing azurite, malachite, chalcopyrite and chrysocolla, careful application of Jackel's method to chrysocolla from Tyrone, N.M., failed to give a high recovery. MATERIALS AND TECHNIQUE Samples from Inspiration, Ariz., and Tyrone and Magdalena, N. M., were used for experimentation and verified as true chrysocolla by leaching tests, specific gravity tests and X-ray diffraction. Chrysocolla does not dissolve at pH 4, although malachite and azurite do. Chrysocolla is about half as dense as the copper carbonates. X-ray diffraction analyses by the powder camera method confirmed the samples as true chrysocolla. A captive bubble apparatus, which cast an enlarged image of the air bubble and the mineral surface upon a screen, was used to check on the character of the surfaces. The specimens were prepared by grinding a flat surface on a glass plate using fine abrasive; then they were washed and kept in distilled water until they were to be treated with reagents. Before each reagent treatment, the specimen was carefully checked for cleanliness in the captive bubble apparatus. It was assumed that the surface was clean if, after fine grinding and washing of the specimen, the bubble would not stick. Specimens were handled with glass forceps, and precautions were taken to avoid contamination of the mineral surfaces. Contact angle measurements were carefully made several times on each treated specimen to obtain reliable average values. EFFECT OF pH VALUE AND SODIUM SULFIDE CONCENTRATION In each experiment, a specimen with a freshly ground surface was immersed for 10 min in a solution of sodium sulfide, washed and immersed for 15 min in a solution containing 30 mg per 1 of potassium amyl xanthate. The specimen was then washed again in distilled water and tested for contact angle in the captive bubble apparatus while submerged in distilled water. In this series of experiments, the pH of the sulfidizing solution was varied from 3 to 7, and the concentration of sodium sulfide, containing 60% Na2S, was varied from 50 to 650 mg per 1. Many combinations of pH value and sulfide concentration resulted in no contact between the bubble and the surface, but over a limited range of conditions, contact angles varying from 24ºto 52ºwere obtained. The data in Fig. 1 show sulfidization conditions that lead to bubble contact and those that do not. The region of contact is surprisingly small, which may indicate why flotation of chrysocolla involving sulfidization has proven so difficult in practice. Several features of the system are illustrated in Fig. 1. In the region between pH values of 4 and 6 with sodium sulfide concentrations below about 350

Jan 1, 1963

By Frederic Carter

THE gold, silver, copper alloys have been the subject of several fairly complete investigations by Jänecke, Sterner-Rainer1 and others, and indeed it would seem as if almost too much labor had been expended on them when one thinks of the numerous other ternary alloys calling for more light; however, the combinations of the three metals are actually so widely used in jewelry that they merit perhaps the work done on them. There are a few properties of importance and interest not treated by the authors mentioned which the writer investigated some little time ago, and therefore he has ventured to put on record the results of some of his tests made at that time. He has chosen, as being the two series of most importance to the jeweler, only the 14 and 18-kt. golds, so the subject is by no means so inclusive as that previously treated. As stated, this paper is merely a record of tests made in a practical manner on two useful series of alloys, and is not at all a critical study of their properties. 14-KARAT ALLOYS These alloys are important because they are the most generally used in 14-kt. jewelry; by changing the proportions of silver and copper there are obtained all shades of color from the green of the alloy containing gold and silver but no copper, to the red of the alloy containing gold and copper but no silver. Many 14-kt. gold alloys are made with the addition of zinc to the three metals mentioned here; the added metal does not appreciably alter the color of the alloy nor has it, in general, much effect on the working properties; it may, however, prove useful as part of the zinc added may act as a deoxidizer and render the alloy free of gas. It is not a necessary addition because with proper precautions all the 14-kt. gold alloys containing only silver and copper in addition to the gold can be made free of gas and capable of being cold rolled without cracking. The alloys in which approximately equal quantities of silver and-copper

Jan 1, 1928

By Frederic E. Carter

THE gold, silver, copper alloys have been the subject of several fairly complete investigations by Jänecke, Sterner-Rainer1 and others, and indeed it would seem as if almost too much labor had been expended on them when one thinks of the numerous other ternary alloys calling for more light; however, the combinations of the three metals are actually so widely used in jewelry that they merit perhaps the work done on them. There are a few properties of importance and interest not treated by the authors mentioned which the writer investigated some little time ago, and therefore he has ventured to put on record the results of some of his tests made at that time. He has chosen, as being the two series of most importance to the jeweler, only the 14 and 18-kt. golds, so the subject is by no means so inclusive as that previously treated. As stated, this paper is merely a record of tests made in a practical manner on two useful series of alloys, and is not at all a critical study of their properties. 14-KARAT ALLOYS These alloys are important because they are the most generally used in 14-kt. jewelry; by changing the proportions of silver and copper there are obtained all shades of color from the green of the alloy containing gold and silver but no copper, to the red of the alloy containing gold and copper but no silver. Many 14-kt. gold alloys are made with the addition of zinc to the three metals mentioned here; the added metal does not appreciably alter the color of the alloy nor has it, in general, much effect on the working properties; it may, however, prove useful as part of the zinc added may act as a deoxidizer and render the alloy free of gas. It is not a necessary addition because with proper precautions all the 14-kt. gold alloys containing only silver and copper in addition to the gold can be made free of gas and capable of being cold rolled without cracking. The alloys in which approximately equal quantities of silver and copper

Jan 1, 1928

By M. Duclos, A. Sawatzky

A simple model has been developed which describes the steady-state solute distribution in Ti-H type systems above the eutectoid temperature in the presence of a temperature gradient. The solute distribution is dependent on the shape of the phase boundaries. An interesting result, and one that is not observed at steady state in thermal diffusion below the eutectoid temperature, is the existence of a two-phase region. The heat of transport for hydrogen in a titanium, Q*a, over the temperature range 275" to 650.C is determined to be 4500 * 230 cal per mole. The heat of transport for hydrogen in B titanium, QB* over the temperature range 320" to 590.C is found to be 630 ± 200 cal per mole. It is also shown that thermal diffusion provides a method by which phase bounduries above the eutectoid may be determined in Ti-H type systems. IN modern technology materials are being used at constantly increasing temperatures under greater temperature gradients. Thus atomic migration in metal alloys due to a temperature gradient (thermal diffusion) may in some cases occur to an observable extent. The thermal diffusion of hydrogen in zirconium has in recent years received considerable attention1-' because of the use of zirconium alloys in nuclear power reactors. The thermal diffusion kinetics below the eutectoid (547°C) are fairly well understood. At steady state the solid solution, a, and hydride, 6, phases are completely separated with the hydride precipitating at the lower temperatures. No experimental work has been carried out in the a + B region although Droege4 suggested that a complete separation of the two phases, as observed at temperatures below the eutectoid, might not always occur. In the present investigation a simple model has been used to determine the steady-state solute distribution under a temperature gradient in Zr-H type systems heated above the eutectoid temperature. The solute distribution is shown to be dependent on the shape of the phase boundaries in the constitutional diagrams and several typical cases are discussed. The model has been applied to Ti-H. This system was chosen in preference to Zr-H because of its much lower eutectoid temperature (-300°C as compared with 547.C), thereby reducing experimental errors due to oxidation and hydriding. The heats of transport for hydrogen in the a and B phases of titanium also have been determined since they were required to compare the proposed thermal diffusion model with experiment. THEORY In the presence of a temperature gradient the atomic flux in a single-phase region of a two-com-ponent system of which the atoms of only one component are diffusing is given by:' J = - U\dx + RT3 dx) which can be written as: j-D(dn/dt +Q*n/RT2)dt/dx [11 J - -D\dT + RT2)dx [1] where D = diffusion coefficient, n = solute concentration, T = absolute temperature, R = gas constant, dT/dx = temperature gradient, and Q* = heat of transport. At steady state (J = 0) Eq. [I] leads to the solute distribution: n = noexp Q*/RT where no = a constant depending on total solute content. The heat of transport Q* can be experimentally determined from the steady-state distribution. In the present paper we shall determine the solute distribution in systems having the constitutional diagram exemplified by Ti-H shown in Fig. l.' As shown, N,(T) and NB(T) are the equilibrium solute concentrations in the a and 0 phases at temperature T. Lines AA' and CC' define the region of interest to us. The following assumptions are made: 1) Steady-state conditions prevail. 2) In a single-phase region all points on an isotherm have the same thermodynamic potential so that the composition over an isotherm is uniform. If a two-phase region exists, thermodynamic equilibrium is found only at phase interfaces. However, we assume the component of the concentration gradient along an isotherm to be small so that the composition in each phase is approximately the same as at the interface and is given by the constitutional diagram, Fig. 1. 3) There is appreciable diffusion of only one component. 4) We shall consider only the case where Qa*, QB*, and Qg*, the heats of transport for solute diffusion in the a, B, and 6 phases, respectively, are positive. This has been observed for the thermal diffusion of hydrogen in zirconium3 and titanium.10 We will show that the steady-state solute distribution above the eutectoid is primarily determined by the heats of transport and the temperature dependence of Na(T) and Np(T). It may be quite different from the steady-state distribution below the eutectoid. For example, we will see that, under certain conditions,

Jan 1, 1970

By J. Bulina, J. T. Brown

SINCE the inception of vacuum cold-hearth arc melting of high-temperature alloys (about 4 years ago) it has been theoretically reasoned and qualitatively found that better mechanical properties are often obtained from alloys which have been melted by this practice. Mechanical properties are emphasized in this evaluation because of their importance in design. Vacuum-arc melting has an intrinsic advantage in that it creates an ingot grain structure which is easier to forge and thus leads to greater yields for the finished product. The greater yield naturally gives the process an economic basis when the cost per pound of alloy is rather high. However, the question stressed here is, does the process create an alloy with inherently better properties? There are several theoretical reasons for suspecting that it does. One is the vacuum refining which should permit lowering the content of harmful residuals with high vapor pressures. A second is the vacuum process which should preclude the formation of harmful distribution of oxides, nitrides, or carbo-nitrides, by keeping the amount of such constituents formed to a minimum. A third is the vacuum-arc cold-hearth method which prevents the possibility of pick-up of harmful elements from a refractory crucible since none is used. Fourth, the rapid solidification rate, induced by having a cold mold and only small amounts of molten metal at any one time, minimizes the segregation of elements like titanium, aluminum, and molybdenum from the top to the bottom of the ingot. This rapid solidification rate also decreases the tendency of the above elements to form undesirable phases by segregating locally. Another less frequently considered vacuum-arc melting advantage is the inherently finer-grained ingot structure which can be produced. Finer initial grain size leads to better forgeability, and means that after relatively small reductions to billets or final forged products a finer-grained material is obtained, which, by virtue of its finer grain size, would usually have greater stress-rupture ductility.

Jan 1, 1960

By P. B. Butler

IN common with others, the zinc industry found itself after the war largely over-capitalized, a condi-tion which still exists notwithstanding that Tri-State production has doubled since prewar days. This is partly due to the abnormal war demands and partly because of the war impetus given to research, a stim-ulus that because of its success has persisted (and probably will persist) constantly since then. Improved practice and metallurgy resulting from research are today responsible for an increased pro-duction in the Tri-State district of 15 per cent over the practice of five years ago, and the giant strides in this respect in the western states together with the more moderate advance in the Tri-State district has thrown out of equilibrium the more or less balanced production of before the war and production has con-sequently gained on consumption, a condition resulting in rapidly narrowing profits in the Tri-State field, where the present average cost is actually greater than the price received for our product. Despite this condition, no thinking person will de-plore the cause or means used to achieve a greater production and, as this progress is merely the economic application of intelligent thought, it follows that equal effort and thought may be expected to produce the remedy. It has been suggested that the practical application of research has resulted in less need for man-power and consequently in the lessening of employment to common labor and to engineers. I cannot think that such is the case although personally I have received more ap-plications for employment during the last two years than ever before. But when one considers the strides production of all commodities has taken, it is difficult to reconcile this immense development with the possible increase in pop-ulation especially in view of our stringent immigration laws. Whether or not improved industrial methods are responsible for the lessening of employment the ques-tion as to the wisdom of such improvement is hardly debatable. While the Tri-State district of Oklahoma, Kansas and Missouri continues to be the leading factor in the zinc¬mining industry, gradually lowering prices during 1925 and 1926 and a. decided drop during 1927, have de-creased its production almost 20 per cent, this tonnage having largely been replaced by western concentrates.

Jan 4, 1928

Alexander N. Winchell, Butte, Mont. (communication to the Secretary): Mr. Spurr calls attention to the fact that an ore-deposit may be due to a succession of concentrations at different geological epochs. He cites an example of such a condition on Napoleon creek, a branch of Forty-Mile creek, Alaska. It will perhaps be of interest to call attention to another example of the same general character, not so remotely situated. The example referred to is located on Pole creek, a tributary of Cherry creek, in the extreme northeastern part of Madison county, Montana. An excellent geological map of this region is to be found in the Three Forks folio (No. 24) of the United States Geological Survey. According to this map, Pole creek, in its upper course, occupies the contact between the " Flathead " formation, which Peale correlates with the Middle and Lower Cambrian, and an area of gneisses and schists supposed

Jan 1, 1903

By P. Bardzil, J. Gurland

An experimental study of the variation of transverse-rupture strength with composition Anexperimentaland grain studysize has shown that the strength reaches a maximum for values of the mean free path between carbide particles of 0.3 to 0.6 microns. The fracture oforiginates in and proceeds through the carbide grains mainly. Impact strength and hardness also were recorded. MOST of the physical properties of sintered carbides vary linearly with composition. The transverse-rupture strength, however, shows a unique behavior. As the amount of binder metal is varied from 6 to 25 pct by weight, the strength at first increases; then, between 15 and 20 pct Co, it reaches a maximum of nearly 400,000 psi, and finally decreases with further additions of binder metal. This behavior of the transverse-rupture strength has been reported, among others, by Englel and Sandford and Trent.' The significance of these observations has not been discussed in the literature. That it may be of more than specific importance is indicated by the very similar variation of strength with composition encountered in other systems sintered in the presence of a liquid phase, such as Tic-Ni3 and Fe-Cu.' Experimental Details All compacts were prepared and sintered according to normal industrial practice. The average diameter of WC grains and the mean free path between grains were measured on metallographically prepared samples by a method of linear and planar analysis sing the relations where d is the average diameter of dispersed grains; Nl is the number of noncontiguous grains intersected on a metallographic plane by a line of unit length; N, is the number of noncontiguous grains per unit area; P is the mean free path between grains of dispersed phase; and f is the volume fraction of dispersed phase. Approximately 1000 grains were counted on each sample. For each composition d2 was plotted against P, the resulting straight lines serving as a check on the measurements. The distribution curves of the WC powders of different average diameters were homologous, and no attempt was made to influence the grain size by blending powders, adjusting the sintering conditions, or otherwise altering the particle size distribution. Densities were measured by differential weighings in air and water. The degree of densification did not vary consistently with either composition or grain size. The density is influenced by slight amounts of impurities, specifically by 0.1 to 0.2 pct Fe which enters the powders during ball milling. As an illus- -tration of the experimental variations, a number of measured densities are listed in Table I. They are expressed in percentage of theoretical density, as calculated from the published X-ray densities of WC and Co.' For the purpose of determining the transverse-rupture strength, rectangular test specimens (3/16x 3/8x3/4 in.) were broken by loading at the center of a 9/16 in. span. The average strength of five or more samples is reported for each composition and grain size. The compacts were ground on two parallel surfaces only. The load was applied at an average rate of 6,800 psi per sec. Since the elongation after fracture of the alloys is very small, it was assumed that the compacts deform elastically to failure and the fracture stress was calculated by the conventional beam formula. The data for one alloy are presented in Table II as an example of the results and scattering ranges encountered. The precision of the test, as measured by the average difference between duplicates, is of the order of 15,000 psi. The results are strictly comparable only to compacts prepared and tested in the manner described and of similar chemical composition and grain size characteristics. Unnotched Charpy specimens were used for impact testing. Each point represents the average of 3 to 20 samples, the larger number being used in an attempt to determine the influence of grain size. Considerable scatter was encountered, the range from lowest to highest value often amounting to 30 pct of the impact strength. The hardness is reported as a Ra reading, using a 60 kg load with diamond brale indenter. Compositions are given in weight percent.

Jan 1, 1956

Florida State Geological Survey, Tallahassee, Fla Herman Gunter, State Geologist A list of publications will be sent upon request Citizens of the state may obtain publications available without cost, others may have them for postage, or they can be sent express collect Twenty Annual Reports have been issued from 1908 up to and including the 21st-22nd Annual Report (1931). Only three are now available; 4th Annual Report (1912), 15th (1924) and 18th (1927) Reports since 1921 contain statistics on mineral production. All reports contain papers on various subjects, many of which are still available separately, and are so indicated in the list of publications. Seven bulletins have also been issued, principally of interest to paleontologists Bulletin 7, The Pensacola terrace and associated beaches and bars in Florida (1931), is of more general interest Bulletins will be sent upon receipt of postage. Thirteen Press Bulletins, most of which are available, have also been issued, but are of minor interest

Jan 1, 1933

By Henry F. Adams, Guy H. Ruggles

In this paper the authors aim to chronicle the experience and salient points brought out in changing flotation reagents at a concentrator which had probably been using a minimum amount of oil at a minimum cost per ton, to a more complicated system requiring a partial chemical control. The original oils were coal tar and pine oil. The new reagents are lime, xanthate and pine oil. It was found that there were no insurmountable difficulties and eventually the cost of the new reagents per ton of ore proved to be very little more than that of the old. Lime Plant When the question of handling lime came up there were two propositions open: (1) to handle the lime dry; (2) to handle it wet in the form of an emulsion. Granting that a dry lime feeder would function properly, delivering lime uniformly, the chief objection was the dust that would be raised when these feeders were being charged or operated, as the only possible location was on a gallery beneath which men were working. With this objection the handling of lime as an emulsion seemed to be the better scheme. The lime plant which was first installed was for experimental work on one section. This was gradually changed and developed until it was of sufficient size to accommodate 20 sections. The various changes will not be discussed and the following description deals only with the fully developed plant. Crude as it is, and perhaps somewhat expensive to operate, the lime-handling plant has been quite successful. Much has been learned which will pave the way for a better installation in the future. Burnt lime is received loose in standard gage box cars. This is the product of the kilns and has had no screening or sorting. A grab sample is taken from each car as it is unloaded. An average of the analyses of samples from 44 cars gave the following: Available CaO Total CaO, Oxide and Hy- MgO, Fe²O³ + Al²O³, Insoluble, Per Cent. drate, Per Cent. Per Cent. Per Cent. Pek Cent. 88.3 79.2 1.6 ' 1.3 2.2

Jan 1, 1928

By W. O. Hotchkiss

Rock exposures are usually a very small part of the surface area in any mining district and the prospector and geologist must base their deductions as to the area, extent, and structure of various formations upon exposures that seldom form 5 per cent. of the area studied. Most often, outcrops form less than 1 per cent. of an area, so that exploration for mineralized contacts or mineral-bearing formations necessitates drilling, test pitting or tunneling, shaft sinking, and other underground work. In these days of high costs any method that will give definite facts regarding rock? obscured by soil or other material should be used to the greatest possible extent. In the early days of the Lake Superior iron districts, mines were located in the few places where ore was present in outcrops. Later, larger orebodies have been found, in depressions, obscured by soil and other foreign material. Mineralized rocks are oftentimes more weathered, softer, and more easily eroded than unmineralized rocks. It is quite natural, therefore, to expect that such orebodies (particularly where large enough to influence erosion in former physiographic conditions) should lie in depressions and be obscured by later debris. It is not difficult to believe that the history of the development of Lake Superior iron mining may be duplicated in other mining districts, that even larger orebodies than those first mined may be found in areas where the rock exposures, which led to original discoveries, are few or lacking. The chief properties of rocks that can manifest themselves through an obscuring cover are magnetism, electrical effects, radio-activity, gravity, and sound transmission. All of these have been used, to a small extent, to tell us a few things about what lies below the surface that we could not otherwise determine, but none has been used so long and so widely as

Jan 1, 1923