Search Documents

By D. A. Thomas, M. F. Comerford

Poly crystalline wires of Fe-3.2 wt pct Si were cold-drawn to 31, 66, and 87 pct reductions of area. Mechanical properties and tnicrostructures were studied after recovery and re crystallization. An initial increase in strength during recovery was ascribed to strain aging, and subsequent softening was largely due to polygonization rather than re-crystallization. No unique actioation energies could be determined for the recovery process. Rather, activation energies ranged from 60,600 cal per mole at 10 pct recovery to 83,200 cal per mole when recovery was 50 pct complete. Sites for the nucleation of recrystallization were found to depend on time and temperature. In the early stages of re-crystallization, nucleation occurred in deformation hands. Later, or at high temperatures, recrystal-lized grains were nucleated primarily al grain boundaries. Polygonized structures did not seem to be preferred sites for nucleation. MUCH of the research on deformation, recovery, and recrystallization processes in bcc materials has been performed on single crystals or lightly worked polycrystals. Little study has been devoted to the relation of mechanical properties to micro-structure in polycrystals after severe deformation and subsequent annealing. This paper presents the results of a study of the tensile properties and microstructures of Fe-Si wires drawn varying amounts and annealed at a series of temperatures. EXPERIMENTAL PROCEDURE The experiments were carried out on an alloy of the following composition: 3.2 wt pct Si, 0.08 Mn, 0.016 C, 0.005 0, 0.0002 N, 0.0001 H, 0.008 P, 0.034 S. The material was received as l-in.-sq bars cut longitudinally from a hot-rolled slab provided by the Armco Steel Corp. The bars were forged to 3/8-in. rounds, centerless-ground to 0.250 in., and swaged to '0.108 in. All subsequent reductions were performed by room-temperature wire drawing at the rate of 2 in. per min. Each preliminary draft gave approximately 30 pct reduction of area and was followed by a l-hr anneal at 1010°C in dry hydrogen. Three lots of wire were made with ultimate cold reductions of 31, 66, and 87 pct reduc-

Jan 1, 1965

By James R. Garvey

Coal reserves of the United States are enormous. Considered on the basis of proven reserves, and compared with reserves of other fuels, coal constitutes 88% of the proven recoverable energy resources of the nation. That includes oil, natural gas, oil shale and uranium used in burner reactors. Considered on the basis of "ultimate recoverable reserves", that is, those resources which can be extracted with improved technology and at somewhat higher costs and including those resources of all fuels not yet found but believed to be waiting discovery, coal still accounts for 75 % of the national total. In the U.S. hydrocarbon economy about 76% of the total energy needs are supplied by petroleum and natural gas and about 20% by coal. Domestic resources of oil and gas are running dangerously low, and assuming a continued hydrocarbon economy, the 20% supplied by coal may increase dramatically. Nearly a quarter of the petroleum consumed in the U.S. is imported. Natural gas is in shorter supply than petroleum and the problems of its importation seem at least as difficult as those of oil.

Jan 6, 1972

By D. G. Westlake

THE structure observed in thin foils by transmission electron microscopy is not necessarily representative of the initial bulk material. We have shown that hydrogen, originally present in a specimen of vanadium, niobium, or tantalum, can be concentrated by the thinning operation used to prepare foils from the bulk materials.' These foils exhibited domain walls indicative of a tetragonal distortion of the bcc unit cells, probably caused by ordering of the hydrogen in preferred interstitial sites. We believe this ordering does not occur at room temperature in the bulk material which contains less than 1 at. pct H. In a continued effort to prepare metal foils whose hydrogen concentrations remain constant during preparation, we have developed some new chemical and electrothinning techniques for vanadium. Each of the procedures presented in Table I produced foils that were thin enough for transmission electron microscopy. The experiments described below were performed to test the effect of each thinning procedure on hydro-

Jan 1, 1968

By H. J. Struth

The benefits of proration of oil production were perhaps more concretely realized in 1932 than at any time since the oil industry adopted nation-wide production control. Reduced output of crude petroleum, which brought the daily average of the United States down to approximately 2,000,000 bbl. from a peak in 1931 of more than 2,600,000, had a telling effect on the trend of oil prices. Mid-Continent crude was advanced in price from 776, for 36-gravity oil, to $1.04 a barrel. California crude, of 26-gravity at Signal Hill, moved forward from 736 to 976 a barrel. Pennsylvania crude, the only exception to the upward trend, rose in price from $1.82 per barrel to $2.02, only to react to $1.72. This was due to local conditions which necessitated an adjustment to overcome competition from other areas of the United States. East Texas continued to exert a far-reaching influence on the crude and gasoline market during 1932. Despite the fact that oil prices were advanced in most fields, large quantities of oil were produced in East Texas in violation of state proration orders, and sold in the market at prices considerably below official postings. This created competitive conditions in the gasoline market that were felt by all refining centers of the United States. The quantity of gasoline produced from cheap East Texas crude was not large, but the volume was sufficient to influence prices in practically all sections of the country. Thus, while the industry's' economic situation showed visible improvement statistically, the unreported and unseen statistics originating in East Texas proved to be an insurmountable obstacle to the economic betterment that was otherwise apparently justified. Somewhat surprising to many was the fact that gasoline consumption was maintained within 10 per cent of the preceding year. Domestic consumption showed only a net decline under 1931 of about 8.5 per cent; exports dropped in volume to the extent of about 23 per cent. As a matter of fact, domestic gasoline consumption was only about 1.4 per cent less than it was in the predepression year of 1929. Exports, however,

Jan 1, 1933

By W. A. Backofen, A. T. English

The kinetics of re crystallization were determined metallographically for a 3-1/4 pcl Si-Fe rapidly compressed at temperatures of 710° to 911°C, and held for various times at the working temperature. As in re crystallization following cold wwk, the time for re crystallization was reduced by increased temperature and strain. Nucleation occurred chiefly at grain edges, although other pre-existing interfaces, notably inclusions, also served as nucleation sites. The importance of intragranular nucleation to grain refinement in hot working is pointed out, together with some possible techniques by which nucleation might be induced within the grains. The observed isothermal growth rates are quite accurately described by the equation G = 4 x 10-'/t (cm per sec), independent of temperature and strain at all but the shortest times. Changes in G during recrystalliza-tion can exceed two orders of magnitude. It is argued that release of stored energy associated with lattice defects cannot adequately explain the time dependence. A suggested alternative involves processes of solute segregation and desegregation in the unrecrystallized matrix and at the moving boundary, respectively. EFFORTS to improve hot-working practice are hampered by an incomplete understanding of the fundamental metallurgy involved. Research directed at establishing the required basic foundation falls into two categories, the first concerned with measurement of mechanical properties under the conditions of high temperature and strain rate which characterize such processing, the second focused on structure and its relation to the deformation conditions. Rossard,' Rossard and Blain,2 and Hardwick and Tegart have conducted many high-speed, high-temperature torsion tests on various metals. One of their objectives was interpretation of stress-strain curves in terms of the structures of specimens rapidly quenched following interruption of twisting. They showed that appreciable hardening occurred in the early part of the test, and that this hardening reflected the concurrent development of an increasingly dense substructure within the grains. The detailed nature of this substructure was observed to depend on the ease of polygonization which, at least in fcc metals, varies with the stacking-fault energy.= By holding specimens after interruption but before quenching, the nucleation and growth of new grains could also be studied. Some success has been realized in relating the microstructure of hot-rolled steel to its temperature:strain rate:strain history with such testing.' The same general observations have been made by others investigating rolling4f5 and drop-hammer forging.~-~ Incident to these experiments, some efforts were made to determine the kinetics of re-crystallization as well as the velocity of the migrating boundaries. The results have been largely qualitative, owing to difficulties of interpreting hardness measurements5 and microstructures. The work described here was undertaken to obtain more quantitative information from tests on a material having suitable metallographic properties, and, in this way, to provide further insight into the fundamentals of this practically most important kind of deformation processing. I) MATERIALS AND EXPERIMENTAL TECHNIQUES Materials. Electrolytic etching of a Si-Fe alloy reveals dislocations and substructure in unrecrystallized grains.8'9 This unique characteristic makes possible a precise determination of the extent of recrystallization. For that reason, it was the material selected for all experiments in the present work. The two particular alloys that were used are identified in Table I. A major difference between "A" and "B" is the number of inclusions, as noted in the table. Most of the experiments were made with material "A". It was received as hot-rolled plate 1 in. thick, sawed to 2-in. widths, hot-forged at 1200°C to 5/8-in. rounds, and finally annealed in a mechanical vacuum at 1000°C for 24 hr. The result was substructure-free grains of mean diameter 0.05 cm.*

Jan 1, 1964

By B. K. Miller, George E. Moore

THE Missouri fire clays are here divided into plastic and semiplastic clays occurring as widespread bedded deposits in east central Missouri and flint and diaspore clays occurring as isolated "sink-hole" deposits in the north central Ozark region. Visual inspection was the first method used in clay prospecting. Thin overburden, hard sandstone "rimrocks," and the occurrence of diaspore float made this method particularly applicable in the flint and diaspore fields. The first drilling tool used was a hand auger. One man can drill 25 to 50 ft. per day at a cost of about 35 cents per foot. Holes can be drilled to a depth of 150 feet. Spud drills are often used where the over burden is hard. This drill uses a slotted earth socket bit. A two-man crew can drill about 100 ft. per day at a cost of about 35 cents per foot. Mechanically powered auger drills have been used extensively in wildcat drilling in the past few years. This type of drill furnishes a continuous set of cuttings. The practical depth limit with this drill is 50 to 60 ft. Two men can drill 300 ft. per day at a cost of about 20 cents per foot. Core drilling is used mainly to prove a known clay deposit. A two-man crew with a No. 22 Sullivan drill can drill about 30 to 40 ft. per day in soft clay, at a cost of about $1.25 per foot.

Jan 1, 1947

Edward Payson Mathewson EDWARD PAYSON MATHEWSON, President of the American Institute of Mining and Metallurgi-cal Engineers, was born in Montreal, Canada, Oct. 16, 1864, of Scotch-Irish ancestors. After preparation in private and public schools, he graduated from McGill University with the degree of Bachelor of Applied Science, in 1885, having specialized in mining engineer-ing and metallurgy. He spent the succeeding summer as a surveyor with the Canadian Geological Survey, being employed in the lake region of Ontario. The following spring he left Canada for Colorado, where he immediately obtained a position as assayer with the Pueblo Smelting & Refining Co. Within three years he became superintendent of the plant, and his success in this position brought him to the attention of the Guggenheim family, whose employ he entered in 1897. He was first in charge of their Pueblo plant, but was soon transferred to their refinery at Perth Amboy, N. J. During the succeeding five years he was in charge of important smelting operations conducted by the firm in Mexico and South America. In June, 1902, Mr. Mathewson accepted a position at the Washoe reduction works at Anaconda, soon thereafter becoming manager of the property. It is unnecessary to recount the improvements and enlarge-ments instituted at that plant under his management, until it became the Mecca of all metallurgists visiting the United States. The esteem in which Mr. Mathew-son was held, not only by the men directly under him, but by all his fellow citizens, was expressed in a send-off such as probably no other plant manager has ever received, when he left Anaconda in October, 1916, to accept the general managership of the British America Nickel Corporation, at Nickelton, Ont., Canada. Soon thereafter Mr. Mathewson accepted an appoint-ment as director of the American Smelting and Refining Co., acting as consulting metallurgist for the company and its subsidiaries. In November, 1919, he resigned this position and opened an office in New York City as a consulting metallurgist.

Jan 3, 1923

By P.V. Roundy, G.R. Mansfield

Public lands in Florida were first withdrawn from entry by President Taft on July 2, 1910, as a conservation measure because of their possible phosphate content. The reserve thus established was subsequently modified by further withdrawals and by restorations, so that on Jan. 1, 1934, it contained 66,796 acres, of which only a small part had been definitely classified. The reserved land was in scattered parcels, ranging from less than 40 acres to 320 or more, distributed in many counties. For administrative purposes and for final disposal of any of the numerous parcels, mineral classification of the land is legally necessary. In 1934 and 1935 the United States Geological Survey, under two successive grants from the Public Works Administration, prospected some 83 tracts of these lands in Polk County, comprising in all about 3300 acres, and six tracts comprising 240 acres in Citrus and Marion Counties. The tracts in Polk County were all in the so-called land-pebble field and the others in the hard-rock field. The Survey field party was under the direction of P. V. Roundy, from whose unpublished report the material in this paper is largely taken. The foreman of the prospecting crew was J. H. Wingate of Zephyrhills, Fla. The individual tracts were identified through the cooperation of the General Land Office, by transitman Hugh B. Crawford. This prospecting work fitted well the classification adopted for Public Works projects in general: it could not be done on any considerable scale under the Survey's usual appropriations; it gave employment to unemployed labor; and it may be expected ultimately to repay the Government in royalties more than the cost of the exploration. Commercial, Prospecting Methods Commercial methods of prospeeting for phosphate in Florida have been briefly described by Mansfield.' In the hard-rock field, where the floor of the phosphate deposit is extremely irregular, it is customary to drill a.:

Jan 1, 1938

By P. V. Roundy, G. R. Mansfield

Public lands in Florida were first withdrawn from entry by President Taft on July 2, 1910, as a conservation measure because of their possible phosphate content. The reserve thus established was subsequently modified by further withdrawals and by restorations, so that on Jan. 1, 1934, it contained 66,796 acres, of which only a small part had been definitely classified. The reserved land was in scattered parcels, ranging from less than 40 acres to 320 or more, distributed in many counties. For administrative purposes and for final disposal of any of the numerous parcels, mineral classification of the land is legally necessary. In 1934 and 1935 the United States Geological Survey, under two successive grants from the Public Works Administration, prospected some 83 tracts of these lands in Polk County, comprising in all about 3300 acres, and six tracts comprising 240 acres in Citrus and Marion Counties. The tracts in Polk County were all in the so-called land-pebble field and the others in the hard-rock field. The Survey field party was under the direction of P. V. Roundy, from whose unpublished report the material in this paper is largely taken. The foreman of the prospecting crew was J. H. Wingate of Zephyrhills, Fla. The individual tracts were identified through the cooperation of the General Land Office, by transitman Hugh B. Crawford. This prospecting work fitted well the classification adopted for Public Works projects in general: it could not be done on any considerable scale under the Survey's usual appropriations; it gave employment to unemployed labor; and it may be expected ultimately to repay the Government in royalties more than the cost of the exploration. Commercial, Prospecting Methods Commercial methods of prospeeting for phosphate in Florida have been briefly described by Mansfield.' In the hard-rock field, where the floor of the phosphate deposit is extremely irregular, it is customary to drill a.:

Jan 1, 1938

By E. S. Machlin, C. W. Chen

RECENTLY Chen and Machlin' proposed a mechanism for intercrystalline cracking in metals during high-temperature stressing. According to this mechanism the formation of voids at grain boundaries is primarily responsible for intercrystalline cracking. A model has been provided to demonstrate the initiation of submicroscopic cracks and voids at jogs of grain boundaries where grain boundary sliding is inhibited. Submicroscopic cracks can grow as a result of either further grain boundary sliding or localized tensile stress. In the former case, it is believed that grain boundary sliding produces more voids which link together to produce macroscopic cracks and which may lead to the eventual failure of the metal. Concurrently, Nield and Quarrell2 reported their interesting results obtained in a systematic investigation of intercrystalline cracking in two aluminum alloys under various creep conditions. Their observations are generally in agreement with the above mechanism, especially the conclusion that voids are formed as a direct consequence of grain boundary sliding. On the basis of the volume fraction occupied by voids, they could find no confirmation of vacancy condensation as the mechanism for void growth. Furthermore, an important feature of intercrystalline cracking has been likewise pointed out by them that the majority of cracks are not formed at grain corners. Nield and Quarrel1 meanwhile emphasized the importance of grain boundary migration by designating it as one of two main processes operative in the mechanism of crack formation during creep. The designation seems unnecessary because overemphasis of grain boundary migration only complicates the mechanism of void formation. There are two reasons which militate against the inclusion of grain boundary migration in the mechanism of void formation. In the first place, the formation of intercrystalline voids per se does not require grain boundary migration. Secondly, in addition to grain boundary migration, void formation may be minimized by any other process such as plastic deformation which is capable of relieving localized stresses around jogs. Chang and Grant3 have shown that intercrystalline cracking is prevented in aluminum by lattice bending in high stress regions. The influential role played by grain boundary migration in creep has also been realized in our studies. In several cases, voids did not appear at all in grain boundaries whenever grain boundary migration took place prominently during creep. The purpose of this paper is to discuss the effect of grain boundary migration on the formation of intercrystalline voids and other related rupture properties. Experimental evidence indicates that in an unstable grain structure void formation may be markedly modified by structural changes. The abnormally high ductility and the transcrystalline mode of fracture observed in copper at elevated temperatures reveals that effective grain boundary migration minimizes void formation. Grain boundary migration has long been known as a common high-temperature phenomenon in metals with the grain configuration in a nonequilibrium state. Its effect on ductility and mode of fracture has not been recognized until recently.4 Since the introduction of the term "Equicohesive Temperature," the conventional belief has been that below the equicohesive temperature the ductility of metals increases moderately with decreasing temperature until the ductile-to-brittle transition temperature of fracture is reached. In this temperature range, metals fracture in a ductile mode with a "cup-and-cone" fracture surface. Above the equicohesive temperature, ductility remains invariably low and decreases slightly with increasing temperature. The mode of fracture is strictly brittle and intercrystalline. Typical examples have been shown for a brass and copper in Fig. 1 and 9, respectively, in the paper by Greenwood, Miller, and Suiter.5 The observation in the upper temperature range that ductility of metals is low and insensitive to temperature may be explained in terms of void formation at grain boundaries. It is also in accordance with the findings of McLean6 and Fazen, Sherby, and Dorn7

Jan 1, 1961

By Fred D. Rosi

Introduction There is probably no field in which materials research has played a greater role than that of electronics. However, to trace present and future patterns of materials research in electronics is not an easy assignment, since this industry has a high degree of dynamism in its growth, and is busily engaged today in the scientific improbabilities of only recent yesterdays. On the other hand, this task seems especially appropriate since electronics is a truly frontier industry - one whose place in American industries has advanced from 50th prior to World War II to 6th in 1967, with sales of more than $22 billion. And this growth has been associated with the equally rapid progress of science and technology over the period - in particular with the emergence of materials science as a vital force in underscoring this progress. For several reasons this parallel growth is not too surprising. First, by its very definition electronics is a science that essentially deals with the nature, behavior, detection, generation, control and utilization of electrons in solids or at their surfaces. Second, in the electronics industry, systems are made of an integration of components, and these components with their interconnections are made of materials. Thus, the basic building blocks of systems are materials; and it has been largely the advances in materials research and technology that have led to new and improved devices and systems. It follows, therefore, that the broadening of the frontiers in electronics through the exploration of new territories is tantamount to scientific discovery and materials innovation to a degree found in no other major industrial activity. But to put this in the proper perspective of present and future materials trends, it would be appropriate first to survey historically the progress in electronics by pointing out major scientific discoveries and associated materials research patterns that have led directly to its tremendous growth. Then from this base we can consider recent trends in materials research that could form the basis for future progress in the electronics industry. In my review I shall examine the areas most familiar to me, so I must acknowledge at the outset that this survey is not all-inclusive.

Jan 1, 1971

By W. Bonfield

The temperature dependence of the microscopic yield stress (the stress to produce a plastic strain of 2 x 10-6 in. per in.) and the stress-plastic strain curve of polycrystalline Cu 1.9 wt pct Be have been measured for the solution treated condition, an intermediate condition containing G.P. zones and ?' precipitate and the overaged ? precipitate condition, in the range from -58° to 200° C. A transition in micro -yield behavior and a large temperature dependence were noted for the intermediate condition, which are interpreted in terms of the interaction of glide dislocations with two differently sized zones. In comparison the microscopic yield stresses of the solution treated and overaged conditions were less sensitive to temperature variations and are satisfied by the Mott-Nabarro and dislocation bowing theories, respectively. A determination of the temperature dependence of the yield stress of a precipitation hardening alloy has provided a powerful tool for evaluation of the operative deformation mechanism. There is a marked contrast between the effect of temperature on the yield behavior of a metal containing coherent zones or intermediate precipitates, which can be "cut through" by mobile dislocations, and a metal containing a dispersion of noncoherent particles, through which dislocation "bowing out" is the dominant role of deformation.' These studies have in general been confined to single crystals, as it was considered that similar experiments on polycrystalline material did not produce good data because of the lack of sensitivity with which the yield stress could be determined. However, this objection has been removed by the introduction of mi-crostrain techniques, with which the yield stress in polycrystalline materials can be measured to a strain sensitivity of 10-6. Such measurements have not only shown that the deformation of polycrystalline precipitation hardening alloys can be examined with the same detail as single crystals, but also that some unexpected results are obtained.' In this paper the results obtained from a study of the temperature dependence of the microscopic yield stress (the stress to produce a plastic strain of 2 x 10-6 in. per in.) and the stress-plastic strain curve of a polycrystalline Cu 1.9 wt pct Be precipitation hardening alloy (Berylco 25) are discussed. The temperature dependence of the alloy was measured for three different conditions: 1) The solution treated condition (a supersaturated solid solution of a containing ~12 at. pct Be3) which is obtained by water quenching the alloy from 800° C. 2) The condition of y' intermediate precipitate, to- gether with some G.P. zones,' which is produced after an aging treatment of 2 hr at 315°C from the solution treated condition. (The alloy was cold rolled to 40 pct reduction prior to aging to minimize grain boundary precipitation effects.)4 3) The condition with equilibrium ? precipitate structure2 which is developed after an aging treatment of 24 hr at 425° C. EXPERIMENTAL PROCEDURE Tensile specimens of gage length 1 in. and with rectangular cross section of 0.18 by 0.06 in. were prepared from the solution treated, cold rolled alloy and were either resolution treated for 1 hr at 800°C, followed by water quenching, or aged for 2 hr at 315°C and 24 hr at 425° C to produce the desired precipitate structures. The microstrain characteristics of the aged specimens were determined at temperatures from —58" to 200° C and those of the solution treated specimens from -58° to 30° C. Each temperature was controlled to ± 0.2°C, which was a level of stability sufficient to eliminate thermal expansion effects from the measurements (~1.2°C temperature increase produced an extension of 2 x 10-6 in.). The microplastic behavior of the specimens in the temperature range below 82" C was measured with a standard Tuckerman strain gage,5 while at temperatures above 82°C a modified Tuckerman gage with a reduced strain sensitivity (4 x10-6 in. per- in.) was used. A load-unload technique was used to establish values of the microscopic yield stress. The specimen was strained at a constant cross head speed of 2 x 10-2 in. per min to a given stress level, at which the total strain was measured. Then the specimen was immediately unloaded at the same rate and any residual plastic strain determined. This procedure was repeated for an increasing series of stress levels until the microscopic yield stress was established by a direct measure of the stress to produce a residual plastic strain of 2 x 10-6 in. per in. (It should be noted that, as reversible dislocation motion occurs at stresses less than the microscopic yield stress,2 the plastic strain rate at this level was not constant.) In an ideal test, the microscopic yield stress would be determined from a continuous stress-strain measurement, rather than from a load-unload sequence, in order to eliminate mechanical recovery effects.6 However, it was found experimentally that mechanical recovery was negligible in Cu 1.9 wt pct Be at small plastic strains for all the temperatures investigated, as the microscopic yield stress was independent of the number of load-unload cycles employed (i.e., the values measured for specimens subjected to different numbers of cycles was within the experimental scatter determined for specimens tested in an identical manner). Therefore, it is reasonable to consider the microscopic yield stress determined in the load-unload

Jan 1, 1969

By Arthur Notman

DESPITE the tremendous drop in the volume of domestic production of metals, their prices, and profits, the world as a whole has managed to produce and consume nearly as much as in 1937. Measured by production, 1937 was the record year for copper, lead, and zinc. The Copper Institute figures for 1938 (estimating December as equal to November) show that although apparent domestic consumption declined 309,422 tons, foreign consumption increased 133.035 tons. The total for 1938 was 1,971,790 tons compared with 2,148,177 tons for 1937. The domestic decline was 38.5 per cent, the foreign increase 9.9 per cent, and the total decline 8.2 per cent.

Jan 1, 1939

By C. K. McArthur

The subject of classification is so broad that this discussion is confined to what the author believes is of prime importance in connection with proper grinding and classification. The years past have witnessed many noteworthy changes in fine grinding and classification, which have been accompanied by a readjustment of ore-dressing flowsheets for the preparation of better ground and/or sized products at an expenditure of less power, steel and maintenance than formerly. Nowhere in the industry is more being done in the way of experimental work to lower costs than in grinding circuits, because, at best, grinding costs are high. Recent years have indicated that, on the average, finer grinding has a real application. Without careful preparation of the process feed, no operation can be highly efficient or successful. In an earlier paper, the findings of an extensive survey at representative concentrators were presented1. Also, in the year of 1935, a technical discussion was given by Dr. J. V. N. Dorr (Some Notes on Classification Trends in America) before the Chemical, Metallurgical and Mining Society of South Africa In both papers mentioned, much has been said regarding flowsheets, grinding and classification. The author is very familiar with these papers, having had considerable to do with the actual operation of the flowsheets, as well as large mills and classifiers in the work described. Some data from the second paper have been included in the following discussion. Circulating Load In this particular paper it seems advisable to deal with the classification phases of the work that to a major extent govern the success of any closed-circuit grinding unit. The question has often been asked in connection with a closed circuit: "What circulating-load ratio should be carried?" This is really an

Jan 1, 1939

By C. K. McArthur

The subject of classification is so broad that this discussion is confined to what the author believes is of prime importance in connection with proper grinding and classification. The years past have witnessed many noteworthy changes in fine grinding and classification, which have been accompanied by a readjustment of ore-dressing flowsheets for the preparation of better ground and/or sized products at an expenditure of less power, steel and maintenance than formerly. Nowhere in the industry is more being done in the way of experimental work to lower costs than in grinding circuits, because, at best, grinding costs are high. Recent years have indicated that, on the average, finer grinding has a real application. Without careful preparation of the process feed, no operation can be highly efficient or successful. In an earlier paper, the findings of an extensive survey at representative concentrators were presented1. Also, in the year of 1935, a technical discussion was given by Dr. J. V. N. Dorr (Some Notes on Classification Trends in America) before the Chemical, Metallurgical and Mining Society of South Africa In both papers mentioned, much has been said regarding flowsheets, grinding and classification. The author is very familiar with these papers, having had considerable to do with the actual operation of the flowsheets, as well as large mills and classifiers in the work described. Some data from the second paper have been included in the following discussion. Circulating Load In this particular paper it seems advisable to deal with the classification phases of the work that to a major extent govern the success of any closed-circuit grinding unit. The question has often been asked in connection with a closed circuit: "What circulating-load ratio should be carried?" This is really an

Jan 1, 1939

By C. K. McArthur

THE subject of classification is so broad that this discussion is confined to what the author believes is of prime importance in connection with proper grinding and classification. The years passed have witnessed many noteworthy changes in fine grinding and classification, which have been accompanied by a readjustment of ore-dressing flowsheets for the preparation of better ground and/or sized products at an expenditure of less power, steel and maintenance than formerly. Nowhere in the industry is more being done in the way of experimental work to lower costs than in grinding circuits, because, at best, grinding costs are high. Recent years have indicated that, on the average, finer grinding has a real application. Without careful preparation of the process feed, no operation can be highly efficient or successful. In an earlier paper, the findings of an extensive survey at representative concentrators were presented1. Also, in the year of 1935, a technical discussion was given by Dr. J. V. N. Dorr (Some Notes on Classification Trends in America) before the Chemical, Metallurgical and Mining Society of South Africa In both papers mentioned, much has been said regarding flowsheets, grinding and classification. The author is very familiar with these papers, having had considerable to do with the actual operation of the flowsheets, as well as large mills and classifiers in the work described. Some data from the second paper have been included in the following discussion. Circulating Load In this particular paper it seems advisable to deal with the classification phases of the work that to a major extent govern the success of any closed-circuit grinding unit. The question has often been asked in connection with a closed circuit: "What circulating-load ratio should be carried?" This is really an

Jan 1, 1937

SAMUEL L. HOYT.-The question of adding the ferromanganese to the ladle or to the furnace involves both theoretical and practical questions and its discussion might very easily occupy the rest of the day. One of the points to be kept in mind is the desirability of obtaining uniform steel. If ferromanganese is added to the ladle, it is necessary first to melt the manganese and then to distribute uniformly throughout the heat. The only heat available for this purpose is that of the molten steel itself. No doubt sufficient heat is present, but in our desire to pour the steel as quickly as possible there is hardly sufficient time allowed, many times, for the proper distribution of the manganese. In other words, this is an operation which takes a certain amount of time and any undue shortening of the time allowed must affect the quality and uniformity of the steel. Again, this particular method does not lead to as efficient a use of the manganese as might be desired; a contention which is based on theoretical grounds. In concentrated solution, manganese will completely reduce all the ferrous oxide, the presence of which I hypothecate and produce, as the reaction product, manganese oxide. In dilute solution, the manganese only partly reduces the iron oxide, but the manganesee oxide which does form dissolves the iron oxide in simple solution. The dissolution of ferrous oxide in the manganese oxide will result in a more economical utilization of the manganese and an equal purification of the heat. This whole point, at present, has not been definitely proved and its answer will involve very difficult research work. On the other hand, if the manganese is added to the furnace, the heat of the furnace is used to melt the alloy and there is plenty of time during tapping for the manganese to be very uniformly distributed throughout the steel. By distributing the alloy throughout the charge we can secure a better utilization of the manganese than is possible if the addition is made to the ladle. Certain other points, such as the recovery, have been dealt with at greater length in the paper.

Jan 4, 1919

By Edel Moldenke

BURMA has long been known for its ruby, tungsten, and tin deposits, and, lately, for having the largest lead-zinc mine in the world, the Bawdwin Mine of the Burma Corpn. All the coal used, however, is imported from Calcutta; this is a bituminous coal of about 11,000 B.t.u., 24 per FIG. 1.-MAP SHOWING LOCATION OF COAL FIELDS AND TRANSPORTATION ROUTES. cent. ash, and costs about $8 per ton. Bituminous coal has not, thus far, been found, but many lignite deposits are known. The most promising lignite deposits are in the Namma field, Fig. 1, situated in the Northern Shan States of Upper Burma, about 30 mi. south of Lashio, the terminus of the Burma Railway, 750 mi. north of Rangoon. The

Jan 7, 1921

By J. G. Thompson

THE methods employed for the determination of oxides and oxygen in ferrous materials may be roughly classed in two groups, "wet" methods and "hot" methods, the first group including the iodine, electrolytic, mercuric chloride, hydrochloric acid, nitric acid, and chlorine methods; the second group including the vacuum-fusion and hydrogen-reduction methods. The wet methods depend upon preferential solubility in a selected medium to separate the metallic portion of the sample from the oxygen-containing constituents. Subsequent analysis of the insoluble residue permits the isolation and separate determination of individual oxides and compounds. The hot methods depend upon the reduction of the oxide constituents of the sample by means of carbon or hydrogen at elevated temperatures. With the exception of the recently developed fractional vacuum-fusion method, the hot methods do not identify individual oxides and compounds but yield only a single value represent-ing the sum of the oxygen contents of several or all of the oxide con-stituents present. With such diversity in the principles and. aims of the different groups, it is not surprising that concordance of results by differ-ent methods has usually been difficult to obtain. The present cooperative attempt to define more rigorously than has been possible heretofore the accuracy and limits of usefulness of the vari-ous methods, originated in correspondence between Dr. John Johnston, Director of Research of the United States Steel Corporation, and other interested metallurgists. The plan was, briefly, to submit identical samples to a number of laboratories for analysis by different methods and to collate the results of these analyses. The project was endorsed by the Iron and Steel Division of the American Institute of Mining and Metal-lurgical Engineers at the annual meeting in February, 1933, and has been conducted under the joint sponsorship of the Iron and Steel Division and the National Bureau of Standards. The latter organization undertook

Jan 1, 1936

By Hans Lundberg

GEOPHYSICAL methods as described in technical articles generally fail to answer the questions of prospectors and geologists as to which method they should apply and what information they may expect from their application. This article is an attempt to discuss the use of electrical methods with special reference to the prospecting for orebodies and the map¬ping of geologic structure. Especially on virgin ground, geological reconnaissance should precede electrical prospecting, with the object of outlining carefully the orebearing rock and determining the possibilities of elec¬trical prospecting. No electrical survey will then be carried out on ground which, for geological reasons, may be considered barren or where the electrical meth¬ods are inapplicable. As the success of electrical prospecting depends on the difference in conductivity between the ore and the country rock within which the orebody is inclosed, the conductivity of the two should be considered and de¬termined, if possible. The conductivity of an orebody depends on the distribution of conductive ore minerals and, in addition, on its size (length, width and depth). Most minerals with metallic luster show good electrical conductivity; for instance, the sulfides. Zinc-blende is an exception, but as it is often associated with the ore minerals of good conductivity (for instance, pyrite or galena), there is likelihood also of finding zinc.

Jan 1, 1930