Search Documents

By John A. Garcia

A standard set of coal mining laws for the entire United States is hardly practicsble, yet the numerous variations in the state laws for almost every item seems entirely unnecessary. The same useless variations appear in almost every comparable section with no apparent reason except that no attempt has ever been made to codify them, and as they were developed over a long period of time by innumerable individuals and legislatures, the present situation is the logical outcome of lack of cooperation between states. The ventilation of a mine is affected indirectly by many provisions not listed specifically under this heading, so that it would be necessary to tabulate the major portion of all the laws to secure a complete comparable digest; therefore only a few of the more important have been set down here. This point is well illustrated in the section providing for clearance between car and rib, which is intended as a safety measure against personal injury, but is very important from the standpoint of ventilation because of choked airways in mines on two-entry system. Confusing Phraseology Misinterpretation and confusion may be expected from the phraseology alone; one state provides that the scale of the mine map shall be "not more than 100 ft. to 1 in.;'' another state demands "not less than 100 ft. to 1 in." Both probably mean the same thing and seek to prevent the operator from furnishing a map on which the workings will appear SO small that the detail is illegible. Legislation is certainly indefinite that specifies structures must be fireproof when "near" a mine opening, and just what is a "dusty" or "gaseous" mine is open to argument in most of the states. The variation in spacing crosscuts and break-throughs and the limited number of men on a split seem entirely unnecessary, as the distance is not reduced in gaseous fields, excepting in Arkansas and Tennessee, which states produce a comparatively small amount of coal, and the number of men differs 100 per cent. and more for no apparent reason.

Jan 1, 1927

By W. A. Klikoff, I. Fatt

The concept of fractional wet wattability is examined. Fractional water wettability of a reservoir rock is defined as the fraction of the internal surface urea that is in contact with water. Capillary pressure and relalive permeability of unconsolidated sand are shown to be functions of fractional wettability. INTRODUCTION The petroleum industry has long recognized that wettability of reservoir rock has an important effect on multiphase flow of oil, water and gas through reservoirs. As early as 1928 the American Petroleum Institute sponsored a study of wettability as part of API Project 27 at the U. of Michigan.' Despite 30 years of research, there is still little exact knowledge of the wettability of reservoir rocks. There are two parts to the wettability problem. After agreeing to a uniform nomenclature in regard to wettability,' the first question to be answered is, "What is the in situ wettability of a given reservoir rock?" If this can he answered the next question is, "What part does wettability play in determining the characteristics of multiphase fluid flow through the rock?" This paper represents an oblique attack on the problem of wettability. No attempt is made here to answer the basic question of wettability in situ. instead the consequences of the concept of fractional wettability are examined. Multiphase flow in sandpacks is shown to he highly influenced by fractional wettability. Jennings' has given 3 definition of wettability and the other terms used in discussing wettability. These terms must be applied to the physical situation existing In reservoir rock. A survey of the pertinent literature from 1928 to 1956 indicates that the concept of a contact angle was applied to reservoir rock in the same way it would be applied to a flat, homogeneous surface. Attempts were made to state quantitatively the wettability of a reservoir rock in terms of a contact angle which was presumably constant at all points on the very rough and heterogeneous interior surface of a porous rock. Calhoun, et al,3-6 prepared synthetic consolidated and un-consolidated porous media in which they claimed there was a known uniform contact angle. They then showed the effects on the capillary pressure and relative permeability characteristics of varying this angle. The API Project 47 at the U. of Texas' and others' have made extensive studies of an indirect approach to the contact angle through the use of heat of wetting data. Even if successful. however, this approach also states the wettability of porous rock in terms of a contact angle which is uniform over the entirc surface. If the angle varies from one part to another on the internal surface, there is no way of determining from the measurements the area distribution of contact angles. In 1956 Brown and Fatt5 suggested that the concept of a contact angle, as applied to reservoir rock, be abandoned. This suggestion was made because it is known that the internal surface of most reservoir rocks is composed of many different minerals, cach with a different surface chemistry and a different capacity to adsorh surface active materials from reservoir fluids. Furthermore, the operation of a contact angle in determining the form of a fluid-fluid interface is difficult to picture in the very complex geometry of a pore. Brown and Fatt proposed that the wettability of reservoir rock be stated in terms of the fractional internal surface area that is in contact with water or oil. All surfaces on which there is water are called water-wet; surfaces on which there is oil are called oil-wet. The fractional water wettability is then stated as a number which represents the fraction of the internal surface that is in contact with water. A symmetrical statement can be made for the fractional oil wettability. The concept of a fractional wettability as previously stated has in its favor the recognition of the heterogeneous mineral composition of most reservoir rocks. Another point in its favor is that fractional wettability can be measured quantitatively with relative ease. Hol-brook and Bernard10 se a simple dye adsorption test to obtain fractional wettability of reservoir rocks. Amott11 uses a combination of imbibition and displacement to arrive at a wettability index of reservoir rocks which seems related to fractional wettability in the range 0.25 to 0.75 fractional water wettability. Jennings" has shown the changes in relative permeability that take place when a porous material is changed from unity to zero fractional water wettability. He also shows that reservoir rocks in their natural state, but at room temperature and atmospheric pressure, have relative permeability characteristics which would indi-

By R. W. Culbertson, S. Kasper

During the 1920's, approximately 11,000 small gasifiers were in operation in the United States. They converted about 15 million tons (13.6 Mt) of coal per year into low Btu gas. In some cases, hot raw gas was used for applications such as firing open hearth furnaces or brick kilns. In other cases the gases produced in the gasifiers were cooled, cleaned and desulfurized for various utility and industrial purposes. The steel industry was by far the largest user. The most important fact was that the conversion of coal to a usable fuel gas was demonstrated to be commercial. During the late 1940's and early 1950's, this form of energy was largely replaced by natural gas as the pipeline net work was expanded. Producer gas was no longer economically competitive. Over the past 25 years, government controls on the interstate price of natural gas have maintained this situation. At present only three commercial small coal gasifier plants are still in operation in the United States. These facilities are operated

Jan 1, 1980

By H. J. Modi, P. L. De Bruyn

IN recent years interest has been aroused in flotation rate studies both from a technical and a more practical aspect. With increasing fineness of grind becoming a necessity in treatment of low grade ores, difference:; in flotation rates of various size ranges will assume importance in the evaluation of overall recovery results. Theoretical analysis of flotation kinetics was initiated by Schuhmann,' who sought to define flotation rate of a given mineral and specified size range in terms of certain physical variables of the flotation system. Using as a basis for his analysis the bubble-particle encounter hypothesis previously advanced by Gaudin,' Schuhmann writes for the rate of flotation (R,.) of particles of average size x, Rx = PcPa(x) V F. [1] In this relation Pc and Pa represent, respectively, the probability of collision between particle and gas bubble in a given time interval and the probability of adhesion of particle to the bubble after collision. Rigorously speaking, the term PC does not have the significance of a probability factor, since it depends on the time interval and therefore can be numerically greater than unity. The term c(x) expresses the concentration of particles of an average size x in the flotation cell in weight per unit volume of pulp, and V denotes the total volume of pulp in the cell. The product, P,c(x)V, defines the frequency of particle-bubble collisl.on, and when it is multiplied by P,, the number of collisions per unit time resulting in successful adherence is obtained. The factor, F, measures the froth stability and is introduced because after fruitful bubble-particle contact some particles may still riot reach the froth launder. Coalescence of bubbles in the froth column or too short a bubble life could account for this effect. Schuhmann also introduced the concept of "specific flotation rate" (Q) to allow for the relative abundance of different mineral species in the flotation pulp. The specific flotation rate, having the dimension of reciprocal time, is defined as Eq. 2: Qx =Rx/c(x)v [2] and it also follows from Eq. 1 that Qx = PcPaF. [31 The theoretical aspects of flotation kinetics were also considered by Sutherland,3 who tried to improve Eq. 1 by expressing the probability factors in terms of such physical variables as particle radius (x), bubble radius (X), velocity of bubble relative to particle (v), the number of bubbles per unit volume of pulp (N) and the induction period (A) necessary for air-mineral adhesion. According to Sutherland's treatment, the rate equation, Eq. 1, transforms to R, = [3pX x v N] [sech2 (3 v ?/4 X) ] ?c(x) V [4] where the first term in brackets on the right-hand

Jan 1, 1957

By Frederick Burbridge

The Morning silver-lead-zinc mine of the Federal Mining & Smelting Co. is about 'two miles northwest of Mullan, Ida. The lode is a metasomatic fissure vein. The orebody is approximately 2000 ft. long within the bounds of the property and varies in width from knife edge stringers to 50 ft. It has been developed to a depth of 3600 ft. and stands nearly vertical in Revett quartzite, which .strikes north 65" west. The high-grade veins and lenses are generally mixed with waste (siderite, quartz, and quartzite). The average grade of ore to sorting plant in 1921 was 4 oz. silver per ton, 8.6 per cent. lead, and 4.1 per cent. zinc. Wall rock stands only a short time without timbering. The minimum angle of gravity flow is 45". The ratio of waste sorted out to ore is 6 per cent. No gases are generated underground and temperature has no influence on mining operations. Fresh air is forced down the air raise and up the main shaft. Drifting and Stoping Main drifts 12 ft. wide and 13 ft. high are driven every 200 ft. (vertically) and are connected by raises 125 ft. apart. These raises consist of three compartments (chute, tramway, and timber slide) and are for the purpose of ventilation, access, and hoisting supplies to stopes. Ground is stoped between raises. Chutes are placed every 25 ft. for drawing off ore broken in stopes. Waste for filling is obtained from waste raises off the stope in walls or waste is dumped from the level above down the chute compartment of raises, which is bulkheaded so that waste can be drawn off at any floor as required. Timbering Posts and caps for square sets (varying in diameter from 6 to 24 in.) are cut to length in a sawmill on the surface. No preseratives are used. Timber is taken on a flat car along drifts to a raise nearest the working place and hoisted as required. Practically no timber is salvaged for

Jan 1, 1925

Jan 1, 1896

By J. F. Gallie

From the standpoint of exploration and new discoveries, South Arkansas had a discouraging year in 1944. In January there were 73 untested drilling blocks, and 60 additions were made during the year. Of the total, 65 were condemned by dry holes on or adjacent to them, while 5 proved productive. The latter resulted in the discovery of the Salem Church, Calhoun Wilks, and Strong fields, and the extension of the Village field to the southeast. The year ended with 63 untested blocks, 41 of which were scheduled for tests to the Smackover lime, the state's deepest oil-producing formation. Geophysical activity in 1944 totaled 164 crew weeks, of which 110 were seismic, 43 gravity, and 11 radioactive (Fig. I), in contrast with 674 crew weeks reported for 1943, of, which 563 were seismic and in gravity, Five seismograph and two gravity crews were engaged in exploration in South Arkansas during January 1944. but only two seismograph crews were working there at the end of the year. In addition, exploratory core drills were used for a total of 38 weeks during the year. The year's few discoveries, none of which is considered as having added appreciably to state reserves, were the meager results obtained in the drilling of 62 wildcat wells 2000 ft. or deeper. Of this total (a detail of which appears in Table 2), 42 were drilled to the Smack-over lime or below, The average depth of the 62 wells was 5384 ft., as compared with 4992 ft. in the preceding year, while the average depth of the 42 wildcats in the lime was 5913 ft. in 1944. Fig. 2 has been prepared to show all , wells penetrating to the Reynolds oölitic lime. The 1944 dry holes are circled lightly, while discoveries are heavily circled and shown as producers. Smackover lime fields, producing from the Reynolds oolitic lime member, are indicated in black, and the locations of dry wildcat wells drilled prior to 1944 are also shown. Table 3 provides a listing of all Smackover lime wells drilled through the end of 1944. Production for the year was slightly more than in 1943, totaling 29,282,747 bbl., as compared with 27,521,943 bbl. for the preceding year. The increase was 1,760,804 bbl., or 6.4 per cent, bringing production to a peak exceeded only in the 1923 to 1928 period of flush production from the older shallow fields, principally Smackover. The increase was largely attributable to additional development in the Dorcheat-Macedonia, Atlanta, Fouke, Stephens-Smart, Haynesville, and Village fields, little production deriving from 1944 discoveries. These six fields accounted for loo of the 122 field wells drilled during the year. Annual and cumulative production for the producing life of the state are presented graphically in Fig. 3. Fig. 6 has been prepared by the author to show the producing ages and present known productive limits of all fields in South Arkansas. Production data, as usual, are assembled in Table 2, and provide a further breakdown of producing formations in the individual fields.

Jan 1, 1945

Charles Catlett, Staunton, Va. (communication to the Secretary*):—Mr. Chance's suggestions that the brown hematite-ores of the Potsdam formation are due to the alteration in place of iron sulphide, and that their extension may reasonably he expected to contain valuable deposits of unaltered sulphide, are interesting; hut the facts marshaled by him are too limited

Jan 1, 1909

By Edward Steidle

THAT veterans are crowding the colleges is no longer news; 78 per cent of the 1916-47 enrollment in mineral industries curricula in the United States were veterans, but the rapid comeback from an estimated 1262 total mineral industries students in 1944-45 to 11,422 in 1946-47 is almost astonishing. The figure, which includes 1008 graduate students, is a substantial increase over the previous top record of 9619 in 1938-39. A small part of the increase is caused by the larger number of women entering the field, of whom there were c 9 in 1916-47. Petroleum leads the curricula with 34.5 % of the enrollment, metallurgy is second with 28%, and mining is third with 18%. Table 1. shows all curricula offered and those accredited by ECPD. Using the Mississippi River as a dividing line, 31 colleges in the East and 27 in the West offer curricula in the mineral industries.

Jan 1, 1948

By L. F. Mondolfo, B. E. Sundquist

The undercooling associated with the nucleation of the secondary phase from the liquid by the solid primary phase was studied in sixty binary alloys by means of a hot-stage microscope. It was found that in a system of a and ß, a usually nucleates ß at low undercoolings, but ß does not nucleate a, except possibly at undercoolings approaching homogeneous nucleation. This behavior can be explained in terms of relative interfacial energies and shows that crystallographic disregistry is only a minor factor in heterogeneous nucleation from metallic liquids. PREVIOUS experimental work1-6 on nucleation of solids from liquids has shown that normally nucleation is heterogeneous, and that small solid particles present in the liquid are responsible for the nucleation. These experiments and the theory that has evolved from them have made apparent that there is a "characteristic undercooling" associated with the nucleation of the solid from a given liquid by a given impurity. Little is known, however, about the chemical and structural relationships between the nucleating agent and nucleated solid that control the effectiveness of the nucleating agent in catalyzing the nucleation, as measured by the required undercooling. A review of the literature has yielded seventeen undercoolingsL-6 for the nucleation of solid from liquid metals by "known" nucleating agents. All values come from experiments in which the metal studied was divided into a number of particles (10 to 300 pin diam.) much larger than the number of extraneous impurity particles so as to obtain a large number of particles free of foreign nucleating catalysts. Known nucleating agents are then introduced by coating the droplets with particles or a thin film of the catalyst. Six of the seventeen undercooling values referred to cases where, for various reasons, the identity of the nucleating species was not at all certain. Another six cases involved nucleating agents with a crystal structure that was not known. Four other cases involved undercoolings listed as greater than or equal to undercoolings which were very likely those for homogeneous nucleation. One investigation3 involved adding to droplets powdered oxides, carbides, and so forth that were doubtlessly covered with adsorbed oxide or nitride films. The highly variable nature of these films resulted in highly variable undercooling (as was also found in preliminary work in this investigation). It is apparent that the information on heterogeneous nucleation in liquid metals is too limited to give rise to any definite conclusions on the nature of the catalytic process. With these problems in mind a new method was

Jan 1, 1962

By Donald E. Grimes

In conjunction with Inland Steel&apos;s development of lead-bearing steels possessing improved machin-ability because of tellurium and/or selenium additions, it was decided to determine liquidus and solidus temperatures in the Pb-PbTe-PbSe sub-ternary system. With the exception of alloys in the PbTe-PbSe system, it is believed that no previous study of this subternary has been performed. Thermal analysis was employed in a general survey of the subternary. In addition to PbTe, PbSe, and pure lead, ten ternary compositions were selected at intervals of ten at. pct. Sixty-gram alloys were prepared by sealing an appropriate mixture of the elements in quartz crucibles with a central thermocouple-well under a vacuum of less than 10 p. All three elements were 99.999+ pct pure with only trace impurities detected by spectroscopic examination. After the alloys had been heated at least 20°C above the liquidus in a Kanthal furnace, cooling and heating curves were obtained. Two or more cooling curves were employed both for the determination of each alloy liquidus and for the solidus of those al- loys containing greater than 50 at. pct Pb. Cooling rates were 0.5° to 3.5°C per min during the 5 min immediately prior to the start or end of solidification. For those ternary alloys containing 50 at. pct Pb, the solidus was determined from heating curves. Temperatures were measured with a Pt/Pt-10 pct Rh thermocouple which was calibrated in the same apparatus against the freezing points of zinc (A. D. MacKay—99.999 pct), antimony (A. D. MacKay-99.999 pct), and copper (ASARCO—99.999+ pct) both before and after the experimentation. The only interruptions in the continuous strip-chart recording of the temperature occurred for brief periods at significant points of interest when direct readings were made with a Rubicon Type B potentiometer sensitive to * 1 µv. The average liquidus and solidus temperatures obtained in this investigation are listed in Table I together with probable errors based on the accuracy of the thermocouple calibration and the reproduci-bility of the data. No chemical analyses of the alloys were performed because the synthetic or as-charged compositions were felt to be reliable. The melting points obtained for PbTe (924.7° ± 0.7°C) and PbSe (1084.0° ± 0.6°C) compare favorably with recent findings of other investigators.&apos;-&apos; As indicated in Table I, both the liquidus and solidus temperatures increase as selenium replaces tellurium for a constant atomic percent lead. As a result, the ternary liquidus and solidus temperatures for a given percent lead lie between the corresponding binary temperatures published in the literature. It should be noted that those ternary alloys containing 50 at. pct Pb exhibit a relatively narrow liquid-plus-solid region (<80°C) when compared with alloys containing greater than 50 at. pct Pb. Alloys with 60, 70, or 80 at. pct Pb not only have a much wider liquid-plus-solid region (>500°C) but also exhibit considerably lower and approximately constant solidus temperatures which thus form a virtually isothermal solidus "plane" slightly below the melting point of pure lead (327.3°C). For these alloys

Jan 1, 1965

By B. E. Lindsly

The withdrawal of gas and/or oil in appreciable quantity from a natural oil reservoir causes the pressure within the reservoir to diminish, and if the oil is completely saturated with gas, this dissolved gas begins to evolve from solution. The liberation of gas from solution in oil causes the oil to change in several ways, the principal changes being: (1) reduction in volume or "shrinkage"; (2) increase in specific gravity (decrease in degrees A.P.I.); (3) decrease of energy in the oil; (4) increased viscosity; (5) increased surface tension. As the writer&apos;s investigations have been concerned more with the first three items than with changes in viscosity and surface tension the following discussion relates particularly to the volumetric shrinkage of the oil, to the increased specific gravity, and to the decreased energy in the oil, each caused by the liberalion of dissolved gas. One of the most surprising facts that have developed in the study of high-pressure well-head and "bottom-hole" samples is the great reduction in volume that occurs in some oils when the naturally dissolved gas is liberated. High-pressure samples taken from well heads in the Oklahoma City, Kettleman Hills and Ventura, Calif., fields decreased in volume from 11.2 to 40.5 per cent when the dissolved gas was liberated in reducing the pressure on the sample to atmospheric. The amount of shrinkage an oil undergoes when gas is liberated depends upon the quantity of gas liberated and also upon its composition. A given volume of the heavier gases, propane and butane for example, will occupy more space in the oil than an equal volume of methane. The reason for this probably is that the molecules of the heavier gases are larger than those of the lighter gases. When gases are not in solution, and particularly when they are at low pressures, the distance between the gas molecules is so much greater than the dimensions of the molecules themselves that the mere size of the molecules has little effect upon the space occupied by the gas, Avogadro&apos;s hypothesis, which in effect states that all gases under the same conditions have the same number of molecules per unit volume, relates to this phenomenon. The fact that the heavier gases occupy more space than the lighter gases in the oil, and

Jan 1, 1934

By H. A. Winne, B. R. Prentice

THE announcement of this World Conference on Mineral Resources briefly traced the development of the metals industries over the past 75 years The various phases were characterized as iron and steel for the railroad era, then copper and the electrical age, through alloy steels to the age of light metals in World War II, ending with the curtain rising on the atomic age at the end of the war The interests of mining and metallurgical industries in the atomic age may perhaps be divided broadly into three - groups (1) production of the special materials required by atomic-energy installations and processes, (2) use of atomic power in the mining or refining of materials, (3) use of radioactive isotopes and radiation in metal and chemical processes both for laboratory study and in the production of materials for use in any field In the production of special materials, the mining and metallurgical, scientific and industrial groups have already contributed much to the start of the atomic age The mining, refining and fabrication of the basic uranium to a degree of purity and form suitable for production of plutonium in the Hanford Engineering Works is just one example. The production of graphite for the Hanford piles, sufficiently free of neutron-absorbing impurities to allow a chain reaction with natural uranium, was a signal achievement These, together with many

Jan 1, 1947

By E. H. Timmerman, A. F. van Everdingen, J. J. McMahon

The prevent paper contains a method which combines the material balance equation&apos; with the water influx equation&apos; to obtain reliable values for the active oil originally in place and a quantitative evaluation of the cumulative water influx. The method is illustrated by an application to a reservoir without original gas cap. In the absence of an original gas cap. results may be obtained using only field production and pressure data, PVT analyses. and a minimum of subsurface information. CHARACTERISTICS OF RESERVOIR AND RESERVOIR FLUIDS Production in the field under review is obtained from the top of the Wilcox formation of Eocene age, at a depth of approximately 8,100 ft subsea. The structural map, Fig. 1, shows that the accumulation, half elliptical in shape with the long axis in east-west direction, is trapped to the north and on the upthrown side of a normal fault. A number of east-west faults with additional minor faulting in random directions are found in the general area, and seismic information and production performance indicate in this particular case the existence of a second fault a short distance downdip, with a strike more or less parallel to the fault controlling the accumulation. It is estimated that 1,830 acres were originally underlain by oil and that the maximum thickness of the original oil column, about 37 ft, was only slightly greater than the maximum thickness of the oil-bearing sand. Maximum net sand thickness was estimated at approximately 26 ft. From logging and subsurface information the gross sand volume has been placed at 37.400 acre-ft. which reduces to about 27,500 acre-ft after probable non-productive intervals have been deducted. The following table presents laboratory analyse; data for the Wilcox sand cores. Average Average Samples Considered Permeability Porosity All Samples 236 md ..19.9percent Samples with k>l md 256 md 20.5 per cent Samples with k>8 md 275 md 20.9 per cent Interstitial water was estimated at 15 per cent. The initial gas-oil ratio was approximately 900 cu ft/bbl. and the initial shrinkage factor was determined by the laboratory to

Jan 1, 1953

By M. Shelef, A. W. Fletcher

The effect of alkali sulfates in promoting the sul-fation of nickel and copper in a bulk sulfide flota -tion concentrate by fluidized bed roasting has been studied in the laboratory, and it was shown that the various alkali sulfates promote sulfation to approximately the same extent. The sulfation of a mixture of synthetically prepared iron and nickel oxide and of nickel ferrite has also been studied. Nickel sulfation was promoted by high ratios of Fe:Ni and by the presence of sodium sulfate. THE work described in this paper was a continuation of earlier studies into the role of alkali sulfates in promoting the sulfation roasting of nickel sulfides1,2 in an endeavor to determine how the system was affected by the presence of compounds of iron and copper. The earlier work1 showed that, in the sulfation of NiO at 680°C, the reaction was limited by the formation of an impermeable film of nickel sulfate on the oxide surface. The relative effect of the various alkali sulfates in promoting nickel sulfation varied in the order: Li > Na >Cs > Rb > K A study of alkali sulfate/ nickel sulfate interactions at high temperatures showed that the promoting action was due to the fact that the nickel sulfate product layer sintered and agglomerated only when the more active additives were present. This resulted in the formation of discontinuities in the nickel sulfate layer so that diffusion of the sulfating gases to the NiO surface was no longer impeded and the reaction could proceed to completion. A similar explanation was used for the observation that sodium and lithium sulfates promote the oxidation of NiS to NiO at temperatures below 750°C since small amounts of nickel sulfate were formed during oxidation.2 It was of interest to study the effect of alkali sulfates on the sulfate roasting of a sulfide flotation concentrate which is typical of material treated commercially. In order to control temperature it is essential to roast sulfides in a fluidized bed and this technique was therefore used, although the batchwise operation of a small-scale laboratory reactor does not reproduce all conditions which prevail in full-scale continuous plant. The results obtained are therefore only comparative, and cannot be used for predicting the optimum conditions for metal extraction. The sulfation of synthetically prepared mixed oxides of nickel + copper and nickel + iron and of nickel ferrite was also studied to evaluate the relative effects of alkali sulfates with more complex systems. SULFATION ROASTING OF A SULFIDE FLOTATION CONCENTRATE The bulk sulfide flotation concentrate used in this work contained 7.92 pct Ni, 1.74 pct Cu, 35.66 pct Fe, and 31.28 pct S. The sulfide minerals present in order of abundance were pyrrhotite FeS, pyrite FeS2, pentlandite (FeNi)S, and chalcopyrite CuFeS2. Two samples described as coarse and fine were used. The coarse sample, which was a flotation concentrate (58 pct plus 300 mesh), was ground to 100 pct minus 350 mesh to produce the fine sample. Before roasting, the sample of sulfide concentrate was agglomerated by wetting witli a solution of the alkali sulfate (or water), thoroughly mixing, and drying at 110°C. This gave a cake which was gently crushed and screened, the -18 +100 mesh fraction being used for fluidized bed roasting. A similar-size fraction had been used by the authors in pilot plant work with a 4-in.-diam fluidized bed reactor.&apos; In this work it was found that the molar ratio of additive to the total iron + nickel + copper content of the sulfide sample should be adjusted to a value of approximately 0.06, as this was the optimum amount necessary for nickel sulfation. Experimental. The fluidized bed reactor consisted of a quartz tube approximately 60 cm long and 30 mm in diameter resting in a vertical tube furnace. The sulfide bed (30 g) was supported on a bed of -4 +12 mesh quartz particles 3 cm high, which rested on a sintered quartz disc welded to the tube. The temperature of the furnace was controlled with a variable transformer to give a final bed temperature of 680°C. The bed was fluidized with air or mixtures of air + 10 pct v/v SO2, at a total apparent gas velocity of 60 to 65 cm per sec at 680°C. The SO2 was introduced into the fluidizing air stream only when the oxidation of the sulfides was completed. At the end of the roasting period the calcine was leached with boiling water and the

Jan 1, 1964

By James R. Cudworth

ENGINEERING has been taught at the University of Alabama for over a hundred years. The School of Mining and Metallurgy was authorized by the Board of Trustees in 1887 and four students were graduated in 1888. In 1919 the legislature directed that all mineral industry instruction in the state should be centralized at the University and designated the department of mining of the College of Engineering as the Alabama School of Mines and made financial provisions for carrying on both instructional and research work for the benefit of the mining industry of the state and for cooperation with the U. S. Bureau of Mines, which had established its Southern Experiment Station on the campus.

Jan 12, 1950

By Klaus Emicke

The paper describes the lead refining process operated at Norddeutsche Affinerie (N.A.). Incoming materials are different grades of lead with varying percentages of impurities: Cu, Te, As, Sn, Sb, Bi, precious metals. The facilities are designed for charge-wise operation. After drossing, generally Te, As, Sn and Sb are removed substantially by the Harris Refining Process using fused NaOH. A certain selectivity during refining is achieved by controlled addition of NaNO3. Another refining step is decopperizing by means of elemental sulfur. Complete separation of Te, As, Sn and Sb is accomplished by chemical methods in a leaching plant. A Howard Press is used in the Parkes Process for desilverizing. After vacuum dezinking in kettle, Bi is removed, if required, by means of Ca and Mg. In an end refining step Ca, Mg and Zn are removed by having the lead melt treated with NaOH and NaN03. The refined lead as such, or in the form of special alloys, is cast by an ingot casting machine into 50-kg ingots. Zinc which is used as a precipitant in the Parkes Process is recovered by distillation from the high grade Ag-Zn-Pb crystals in Faber du Faur retorts while the Pb/Ag alloy is fed to the cupellation furnace. Ca and Mg are removed from the Ca-Mg-Bi crystals formed in the course of Bi removal, and the Bi-bearing lead is cast into anodes. The electrolytic lead refining facilities at N.A. are operated largely for the purpose of separating Pb and Bi. These facilities are also used particularly for the refining of Bi-bearing lead which had gone through the above process, but from which Bi has not been removed by Ca and Mg.

Jan 1, 1970

By R. S. Dean. J. R. Long T. R. Graham, Roberson A. H., Armantrout C. E.

The general program of the Federal Bureau of Mines on the study of alloys made with electrolytic manganese has been extended to copper-manganese-aluminum alloys. The initial results of the work are presented in this report and concern a determination of the mutual solubilities of these three metals to form the alpha solid solution. The principal studies of this system, reported in the literature, have been focused on the Heusler alloys containing ro to 30 per cent Mn with 9 to 15 per cent Al. These investigations concern the ferromagnetic properties and the determination of the crystallization contours, with little emphasis on the phases present in the solid state outside of this area. Heuslerl recognized a breakdown of the beta solid solution of the magnetic alloy, which he says decomposes into the alpha, beta, and gamma phases of the copper-aluminum system, somewhat modified by the presence of manganese. Rosenhain and Lantsberry2 examined alloys ranging up to 10 per cent Mn and 10 per cent A1 but were unable to reach definite conclusions concerning the phase boundaries in that area. Krings and Ostmann3 made magnetic studies and examined the system by thermal analysis. They present contours of the liquidus surface but do not place any of the phase boundaries. Corson4 has drawn a hypothetical boundary for the alpha field with few, data to support such construction. The binary systems involved have rcceived considerable attention by numerous investigators, and their general features are well established. The copper-ahminum system (Fig. I) has been thoroughly examined by Stockdale,5 who places the limit of solubility of aluminum in copper at 7.4 per cent at the liquidus and 9.5 per cent at room temperature. Smith6 established the eutectoid temperature at 570°C. by a study of isothermal decomposition of the beta phase. The copper-manganese system (Fig&apos; &apos;) has been recently reviewed by Dean and CO-WorkersS.7 Using high-purity alloys,

Jan 1, 1947

By Armantrout C. E., R. S. Dean. J. R. Long T. R. Graham, Roberson A. H.

The general program of the Federal Bureau of Mines on the study of alloys made with electrolytic manganese has been extended to copper-manganese-aluminum alloys. The initial results of the work are presented in this report and concern a determination of the mutual solubilities of these three metals to form the alpha solid solution. The principal studies of this system, reported in the literature, have been focused on the Heusler alloys containing ro to 30 per cent Mn with 9 to 15 per cent Al. These investigations concern the ferromagnetic properties and the determination of the crystallization contours, with little emphasis on the phases present in the solid state outside of this area. Heuslerl recognized a breakdown of the beta solid solution of the magnetic alloy, which he says decomposes into the alpha, beta, and gamma phases of the copper-aluminum system, somewhat modified by the presence of manganese. Rosenhain and Lantsberry2 examined alloys ranging up to 10 per cent Mn and 10 per cent A1 but were unable to reach definite conclusions concerning the phase boundaries in that area. Krings and Ostmann3 made magnetic studies and examined the system by thermal analysis. They present contours of the liquidus surface but do not place any of the phase boundaries. Corson4 has drawn a hypothetical boundary for the alpha field with few, data to support such construction. The binary systems involved have rcceived considerable attention by numerous investigators, and their general features are well established. The copper-ahminum system (Fig. I) has been thoroughly examined by Stockdale,5 who places the limit of solubility of aluminum in copper at 7.4 per cent at the liquidus and 9.5 per cent at room temperature. Smith6 established the eutectoid temperature at 570°C. by a study of isothermal decomposition of the beta phase. The copper-manganese system (Fig&apos; &apos;) has been recently reviewed by Dean and CO-WorkersS.7 Using high-purity alloys,

Jan 1, 1947

By K. Kim

INTRODUCTION A thorough evaluation of the geologic material being considered must be conducted to determine the feasibility of constructing a large-scale underground facility in a deep geologic formation. The design and construction of a nuclear waste repository in basalt, due to the unprecedented nature of the project, adds significantly to the need for thoroughness of this evaluation and mandates that geoengineering data and analysis be of the highest quality. The investigations required to collect the data encompass in situ measurements and observations, as well as laboratory and field tests. Mathematical (numerical) models, which are required to predict the long-term performance of the repository structure, must be developed to evaluate rock mass behavior at canister, room, and repository scale and eventual 1 y must be validated through in situ tests and monitoring. The information generated from these geo- mechanics investigations is essential for assessing site suitability and will be utilized in the development of the repository design, the engineered barrier design, and the evaluation of repository performance. The Hanford Site near Richland, Washington is one of nine sites throughout the nation being investigated by the U .S. Department of Energy as a possible location for the first high-level nuclear waste repository in deep geologic formations. The process of site characterization is currently in progress. If the site is nominated by the U.S. Department of Energy, an extensive program will be undertaken, the culmination of which will be a decision on the suitability of the site for waste disposal. There are a mu1titude of elements to the proposed site characterization

Jan 1, 1984