Search Documents

By Willis H. Carrier

PARTICULAR interest in the ventilation of deep mines, especially those in South Africa, has been created by a very complete system of cooling of the world's deepest mine, the Turf shaft of the Robinson Deep in Johannesburg. The writer visited this mine in January, 1936, and again in 1937. During these visits and subsequently, a considerable part of the theory involved in rock cooling in tunnels was developed and this has been checked by practical observations of the rates of rock cooling made within mines. The purpose of this paper is to set forth the method of attack of the mine problem. The cooling or air conditioning of mines by the use of mechanical refrigeration was not wholly new 1-5 when the Robinson Deep installation was made. The first mine to be cooled was the Morro Velho mine, in Brazil. The first installation in this mine was put into operation in December 1920, the refrigerant being ammonia.5 The surface cooling gave considerable benefit but it proved inadequate as greater depths were reached, therefore in 1929 two centrifugal refrigerating machines were installed at the 6000-ft. level. These were used in conjunction with the surface cooling system to furnish additional cooling at the lower levels. This later installation used Carrene as a refrigerant. This nonflammable refrigerant, having a boiling point of 104º at sea level, insured reasonable safety, since all parts of the machine operated at subatmospheric pressure. Very favorable reports have been received on the effectiveness of this installation, but no recent data are available. An interesting feature of that plant is that the condenser water is cooled by spraying it into the exhaust air from the mine at the base of the ventilation upcast, which permits the water to be cooled within a few degrees of the wet-bulb temperature of the air entering the upcast, and the only water that has to be supplied for condensing purposes is that lost by evaporation, or about 0.5 per cent of the volume circulating through the condenser. This plan affords an ideal means for the removal of the heat load from the refrigerating system, and of course also from the mine itself. In many mines, however, especially those in South Africa, there is no

Jan 1, 1938

By Horace Pops, L. L. Isaacs

SOLID-STATE transformations at low temperatures are frequently studied by optical metallography. Greninger and ooradian' and Hull and Gar-wood2 have examined the martensitic-type transformations in 0-phase Cu-Zn alloys during continuous cooling below room temperature. The lowest range of temperatures in the apparatus described by these investigators is limited to approximately 110°K. Present studies of reversible first-order phase transitions near liquid-helium temperatures have necessitated the design of a new cold-stage cryo-stat for optical metallography. The features of interest of this instrument are as follows: a) temperatures down to 4.Z°K are obtainable; b) the specimen is always under vacuum, thereby avoiding the condensation of moisture; c) specimens can be rapidly cooled or heated at varying rates, thus permitting studies of transformation hysteresis. Fig. 1 shows the details of the cryostat. All major parts are made of type 304 stainless steel. Both helium and nitrogen cans are Heliarc-welded to the helium filling tube, permitting the use of a common shielding can. Hence, the over-all weight and the area of the evacuated surface are mini- mized. The copper sample holder is screwed into the bottom of the helium can. To assure good thermal contact between the sample holder and the refrigerant, an indium ribbon is placed on the threads

Jan 1, 1964

SPEAKING generally, it may be said that leaching is the simplest method of recovering copper from its ores. Likewise it is perhaps the oldest method of treatment used by copper metallurgists of the modern era. Reliable records indicate that as early as 1752 cupriferous pyrite was leached in the famous Rio Tinto region in Spain. Though the manipulation was quite different from that in use today at Chuquicamata, New Cornelia, Inspiration, and Andes, it resembled that employed by Phelps Dodge at Bisbee, as described in Chapter XIV. Leaching consists of subjecting ore to the action of a liquid solvent or menstruum (usually an aqueous solution) which dissolves the major part of the soluble copper minerals. The resulting pregnant solution is drained off or otherwise separated from the residual ore; and the copper in the solution is then recovered by some appropriate means of precipitation. When sulphuric acid is the lixiviant, as is usual, the simplest procedure is to pass the copper-bearing solution through large troughs containing scrap iron. The iron displaces the copper in the solution, precipitating it as a slime coating the iron and varying in color -from bright copper to a dull black. This may be washed off at intervals, collected as a sludge, dried, and melted with a little fluxing material to produce reasonably pure copper. Usually, of course, the mud is sent to a smelter where most often its destination is the converter or reverberatory furnace. Modern practice uses precipitation on iron only as a complemental process to electrolytic precipitation or deposition, wherein the pregnant copper-bearing solution, acting as the electrolyte in a cell having insoluble anodes and copper cathodes, is depleted of the copper it contains. Cathode copper, 99.5 per cent pure, is produced ready for the market as refined copper, or for a simple process of melting, fire-refining, and casting in

Jan 1, 1933

Solution mining got back in the news recently when Kalium Chemicals, Ltd., a joint subsidiary of Pittsburgh Plate Glass and Armour & Co. announced its plans to go full speed ahead in mining potash by the solution method in its vast holdings 30 miles west of Regina, Saskatchewan. The company is keeping the technical details of this mining technique under wraps for competitive reasons, but company officials insist that the major difficulties in solution mining of potash have been overcome and that the final product will have definite competitive advantages on the open market. Kalium's holdings in the Regina area total about 500 sq mi. The ore-primarily sylvite mixed with appreciable quantities of halite-occurs in the Prairie Evaporite formation at a depth of 5300 ft. The ore zone averages about 100 ft in thickness. Too deep to be economically mined by conventional underground methods, such as is being done at International Minerals & Chemical Corp.'s Esterhazy mine (depth about 3100 ft), Kalium gambled that it could develop a successful method of solution mining even though earlier attempts in Germany, the U.S., and Canada had failed.

Jan 6, 1964

By Alan Morris

IN a previous paper1 the results of cutting tests on free-cutting brass rod were reported. Investigation was made of the effects of variation in lead content, microstructure and cold drawing. The author's reply to the discussion of that paper includes a study of the directional cutting properties of drawn and annealed rod. The present paper records the results of tests made on series of samples in which the tin, iron and copper contents have been varied. The apparatus, used and method of testing are described in detail in the previous paper. The machine is of the pendulum-operated milling type used and described by Airey and Oxford.2 Angular readings of the height to which the pendulum rises after falling from a fixed position, both when a cut is made and when the pendulum swings freely, give the basis for calculation of the energy consumed in making a cut. Careful weighing of the sample before and after cutting gives a measure of the amount of metal removed. The results are expressed in foot-pounds per cubic inch of metal removed, and have been called "unit cutting energy." In the course of the discussion of the author's earlier paper, W. B. Price reported large-scale tests involving some 50,000 lb. of material. These tests indicated that the addition of as much as 0.6 per cent of iron and 0.25 per cent of tin had apparently no adverse effect on the high-speed cutting characteristics of the rod. The rod also contained a small amount of nickel. The test results reported here tend to confirm his observations.

Jan 1, 1933

By D. B. Hobbs, H. O. Burrows, T. D. Stay

ALUMINUM which has lost its original identity as to source may be considered as secondary. This would include scrap originating in the fabrication of aluminum, which is not consumed at the plant of fabrication, and all material resulting from fabrication, which has lost its original identity regardless of whether it be consumed at the plant of fabrication or not. In general, secondary aluminum may be divided into two classes, commercially pure and alloyed. The chief impurities found in commercially pure aluminum are copper, iron, titanium and silicon; while in aluminum alloys, copper, iron, titanium, silicon, zinc, manganese, magnesium, nickel, or tin, may be present in varying proportions. Occasionally lead and antimony are found in secondary aluminum alloys, especially if the alloy results from remelting vender's automotive scrap. Such alloyed elements as are found in the scrap cannot be removed on remelting. In this, the remelting of secondary aluminum differs from the smelting of secondary copper or most other secondary metals. The majority of secondary materials reach the consumer in the form of remelt ingot or remelt No. 12 ingot. This ingot varies greatly in quality, depending upon the source of the material, and the manner in which it is refined and blended. The principal differences between primary and secondary ingot are: 1. The composition of secondary ingot may be more or less indefinite. 2. Secondary ingot may contain more dross and oxide. Secondary ingot may, however, be used successfully in a great many products. RELATION OF PRIMARY PRODUCTION TO SECONDARY PRODUCTION Table 1, compiled from data published by The American Metal Market, gives an approximate idea of the relation of primary to secondary production. Information obtained from other sources leads the authors to believe that the figures for secondary production are somewhat low.

Jan 1, 1928

By M. G. Benz, J. F. Elliott

A new type of solution calorimeter has been constructed to measure heats of mixing, enthalpy increments, and heats of fusion, formation, and reaction at temperatures above 1000°C. With it, measurements hove been made of the partial molar heats of mixing joy tin in the Cu-Sn system from 0 to 13 at. pet Sn at 1127°C and fir nickel in the Cu-Ni system from 0 to 9 at, pet Ni at 1200°C. The integral molar heat of mixing for the Cu-Sn system is strongly negative with a calculated minimum value corresponding to the composition Cu3Sn. The integrnl molar heat of mixing for the Czi-Ni system is slightly positive at these temperatures. These integral molar values have been measured with a probable error less than 30 cal per g-atom at an atom fraction of nickel or tin equal to 0.1. The estimated probable error for the Cu-Sn system is approximately 450 cal for a measured heat of solution of approximately 9000 cal. For the Cu-Ni system it is approximately 700 cal for a measured heat of' solution of approximately 60 cal. A new type of heat of solution calorimeter was designed and constructed to provide a more accurate experimental method for determining heat effects at high temperatures, (T > 1000°C). With it, partial molar heats of mixing, enthalpy increments, heats of fusion, and heats of formation and reaction for metal systems can be measured directly. Previously it has been necessary to rely upon the use of the dropping calorimeter or the van't Hoff equation applied to equilibrium data for this information. For the most part equilibrium data are scarce and difficult to obtain in many cases, and it has been necessary to rely upon the "method of mixtures" for the desired enthalpy measurements. An earlier study1 provides a prototype for this work. The "method of mixtures" as outlined by K. K. kelley,2 "consists of dropping the substance under investigation from a furnace, with controlled and measured temperature, into a calorimeter operating at or near room temperature.'' In this manner the change in the total heat content (enthalpy) of the substance between the temperature of the furnace and that of the calorimeter is determined. In order to determine high-temperature heats of mixing, enthalpy increments, and heats of fusion, formation, and reaction, it is necessary to take the difference between two such measurements, one before and one after the occurrence of the enthalpy change being studied. The desired enthalpy change is then the small difference between two large numbers. Small errors in the large numbers are included as large errors in this small difference. It is this difficulty that must be avoided for accurate measurement of the desired functions. The procedure with the new solution calorimeter consists of dropping the substance under investigation from a furnace, with controlled and measured temperature, into a solution calorimeter operating in the temperature range of 1000o to 1200°C. Measurements in the range of 1200" to 1600°C are planned for the future. By selection of the composition and

Jan 1, 1964

By J. W. Givens, P. B. Crawford

A potentiometric model study has been made of the effect of vertical fractures existing in the matrix of the reservoir on the flooding or cycling performance. Fractures can have unusual flow characteristics. Fluid entering one side of a fracture can emerge on either the same or opposite side of the fracture, depending on the particular streamline. Fracture orientation has a great influence on the sweep efficiency. However, sustained fluid injection may still permit large areas to be swept. INTRODUCTION One can find considerable information available in the literature on the effect of fractures originating at the wellbore on sweep efficiencies of water-flooding or gas cycling programs.1-5 However, there arc few, if any, quantitative data reported in the literature on the effect of vertical or horizontal fractures existing out in the reservoir matrix on secondary recovery performance. Several papers have been presented on the effect of vertical and horizontal fractures on the productivity or conductivity of waterflood and gas injection patterns, but in all cases the fractures initiated at the well and simulated commercial fractures.6,7 It is believed that natural fractures may exist out in the reservoir matrix and would effect the displacement performance. The purpose of this report was to study the effect of a few isolated vertical fractures existing out in the reservoir matrix on the performance of waterflood or gas injection patterns. DESCRIPTION AND EQUIPMENT Since the potentiometric model was described by Lee8 it has been widely used to study numerous types of fluid displacement problems. The potentio- metric model can be used for fluid displacement studies when the following assumptions are valid: (a) steady-state conditions exist; (b) the mobilicy ratio is one; and (c) the capillary and gravitational effects can be neglected. Five-spot and direct line drive square patterns were studied using a copper strip of the desired length and orientation to simulate a vertical fracture in the reservoir matrix. The 20 x 20-in. model was considered to represent only one element of an infinite array of similar patterns. DISCUSSION AND RESULTS FIVE-SPOT PATTERN — ONE FRACTURE BETWEEN INJECTION AND PRODUCING WELLS Fig. 1 shows a quadrant of a five-spot pattem with the vertical fracture existing out in the matrix along a line connecting the injection and producing wells. Length of the fracture was equal to 35.4 per cent of the distance between injection and producing wells. In this particular pattern it is noted that fluid breaks through from the injection well to the producing well when the dimensionless time is equivalent to 26.9. Dimensionless time is defined as volume of fluid injected divided by the volume of displaceable fluid in the pattem expressed as a per cent. The cross-hatched areas of this

Jan 1, 1967

The movement for Federal endowment of engineering and industrial research was revived early in the present Congress by the introduction of two bills into the Senate. The first bill, introduced by Senator Smith of Georgia, provides for the establishment of an engineering experiment station in each state under the direction of and in connection with some university, engineering school, or land-grant college. The state legislature of each state is authorized to designate the institution best equipped to conduct the work but wherever the land-grant college has facilities approximately equal to those of the other institutions of the state, it shall be designated. All designations of institutions are made subject to the approval of the Secretary of Commerce. The Secretary of Commerce is authorized to secure practical uniformity of methods, and efficiency and economical expenditure of funds by indicating such lines of work as shall seem to him important from a military; naval, industrial or national standpoint, but the responsibility for the initiation and conduct of research shall rest with the individual engineering experiment stations. Uniform standards of research are further provided for by making each experiment station a depository of the Department of Commerce and the Bureau of Standards, and the work of each station shall conform to the standards established by the U. S. Government through said bureau, which may whenever practicable utilize the facilities of the station for the prosecution of research.

Jan 8, 1919

SEC. 1. This Institute is incorporated under the Membership Corporations law of the State of New York; its corporate name is American Institute of Mining and Metallurgical Engineers, Inc.; and its abbreviated title A. I. M. E. SEC. 2. The objects of this Institute, as set forth in its certificate of incorporation, are: "To promote the arts and sciences connected with the economic production of the useful minerals and metals, and the welfare of those employed in these industries by all lawful means; to hold meetings for social intercourse and the reading and discussion of professional papers, and to circulate by means of publications among its members the information thus obtained, and to establish and maintain a place for meeting of its members, and a hall for the reading of papers and delivery of addresses, and a library of books relating to subjects cognate to the sciences and arts of mining and metallurgy." ARTICLE II MEMBERSHIP SEC. 1. The membership of this Corporation shall include all those who on the third Monday in February, 1928, were members and all others subsequently elected and qualified in accord with the By-laws of the Institute at the time of such election. SEC. 2. The membership shall be divided into such classes as may be from time to time fixed by the By-laws. ARTICLE III DIRECTORS SEC. 1. The business, financial, professional, technical, scientific and social interests of the Institute shall be managed by a Board of Directors, elected annually by letter ballot in the manner specified in the By-laws, to serve for the terms as set forth in the Certificate of Incorporation. ARTICLE IV AMENDMENTS SEC. 1. Proposals to amend this Constitution may be made by resolution of the Directors or by written petition signed by at least ten members. Such proposals must reach the Secretary not later than October fifteenth. The Board of Directors shall consider them and, in case of petitions, the proposers shall be notified of the opinion of the Board in regard to them, when they may cither withdraw their proposals, or accept any changes suggested, or insist on the original form. All proposals when in final form shall be mailed to all members on or before January first, with the election ballots, and with a ballot in proper form for voting on the amendment in its original or amended form. Ballots shall be received by the Secretary until the second Tuesday in February. The Tellers of the election shall count these ballots,

Jan 1, 1929

By Frank C. Aplleyard

The two calcium sulfate minerals-gypsum and anhydrite-occur in many parts of the world, and gypsum has long been of economic importance in the family of industrial minerals. Gypsum, the dihydrate form of calcium sulfate (CaSO4•2H2O) and anhydrite, the anhydrous form (CaSO4) are frequently found in close association, and it is seldom that a calcium sulfate deposit will consist exclusively of one mineral or the other. Although known gypsum deposits are extensive, anhydrite makes up the largest part of total calcium sulfate reserves. However, it has very minor economic use, and most of the following discussion will be devoted to gypsum. Calcium sulfate is one of the principal constituents of evaporite deposits, and when pure, has the following composition: [Sulfur Combined Lime Trioxide Water (CaO) (SO,) (H2O) Gypsum 32.6% 46.5% 20.9% Anhydrite 41.2% 58.8% -] Deposits of pure gypsum or of pure anhydrite which are large enough to be considered commercial have never been found because of both the metastable relationship between the two minerals, and the presence of impurities such as calcium or magnesium carbonates, chlorides, other sulfate minerals, clay minerals, or silica. As a result most mine production of gypsum will range between 85 and 95% pure. Often it is used as mined, although in certain cases, one or more forms of mineral beneficiation are employed to upgrade the product. End Uses The largest use for gypsum is based upon the unique property which calcium sulfate has of readily giving up, or taking on, water of crystallization. With the application of a moderate amount of heat in a process known as calcining, gypsum is converted to plaster of paris (the hemihydrate of calcium sulfate, CaSO4 ½ H2O) which when mixed with water will set or harden as the calcium sulfate returns to the dihydrate form. This semifinished product, usually called stucco, is then manufactured into a large variety of plasters, wallboard, and block for construction use, or into plasters for industrial applications. About 75% of the gypsum used in the United States is calcined for these purposes. Uncalcined uses of gypsum are principally as a retarder for portland cement, as a soil conditioner, as a mineral filler, and other minor industrial applications. About 25% of the gypsum mined in the United States goes into these markets; however, in less developed countries where construction and other industrial uses may be quite limited, the use of uncalcined gypsum for portland cement retarder may well be the dominant-if not the only-market for the mineral. It has often been noted that calcium sulfate constitutes the world's largest reserve of sulfur, and minor use of both anhydrite and gypsum has been made to produce sulfuric acid or other sulfur compounds such as ammonium sulfate. However, because sulfur is readily available at lower cost from other sources, use of calcium sulfate has been limited to only a few locations where it could compete economically. No such use is reported in the United States at this time. Mineralogy Anhydrite, CaSO4 because of its geologically rapid conversion to gypsum, and relatively high solubility (about 0.2 g per 100 g H2O) is not often found outcropping in climates wet enough to support abundant vegetation except on steeply dipping slopes or other places where hydrated material is continuously removed. Anhydrite rock is most often light to bluish gray in color, and under the microscope, varies

Jan 1, 1983

United Engineering Trustees, Inc James L Head, '50 E C Meagher, '52 Gail F Moulton, '53 The Engineering Foundation E R Kaiser, '54 W M Peirne, '52 E C Meagher, ex officio as Pres , LET Engineering Societies Library Board James Douglas, '52 Frank T Sisno, '50 American Standards Association Mining Standardization Correlating Committee Otto Herres, '51 H H Otto, '51 B F Tillson, '50

Jan 1, 1952

By J. H. Brophy, M. H. Kamdar, J. Wulff

A constitutional diagram for the Ta-W-Re alloy system is presented. Rhenium dissolves in the complete range of solid solutions between tungsten and tantalum up to 48 wt pct in tantalum 'to about 30 wt pct in tungsten. Intermediate x and u phases only are found. X-ray diffraction and fluorescence, metallography and melting-point measurements were employed. THE constitution diagram of ternary alloys of tungsten, tantalum, and rhenium for temperatures above 1000°C is reported in this paper. Alloys in this system rich in tantalum and tungsten are of interest for high-temperature applications, and those rich in rhenium for electronic applications. No ternary phase diagram appears to be available in the literature. The three-component binary diagrams have been previously established1-3 and the present ternary data are consistent with these. EXPERIMENTAL TECHNIQUES Commercially pure tantalum (99.7 pct), rhenium (99.99 pet), and tungsten (99.9 or 99.95 pct) powders were purchased from Fansteel Metallurgical Corp., Chase Brass and Copper Co., and Fansteel or Westinghouse Electric Corp., respectively. These powders were pressed without binder and arc-melted under helium. The preparatory and analytical techniques employed were identical to those used for the Ta-Re system investigation carried out in this laboratory.324 These included X-ray diffraction and metallographic phase identification, X-ray fluorescent and wet chemical analyses, solidus determinations and heat treatments in a resistance-heated tantalum-filament vacuum furnace. For microstructural examinations standard mechanical polishing techniques were used through diamond laps. Polished speciments of all compositions were etched by swabbing with 4 parts HI?, 4 parts HNO3, and 1 part H20. Since the microstruc-tures of alloys containing one or two phases closely resembled their counterparts in the respective binary systems, typical examples are omitted in this presentation. In all the alloys examined, it was possible to observe the number of phases present. Particularly when there were small amounts of one phase involved, it was possible to identify it only by a combined conclusion based on X-ray diffraction, position of an alloy in a composition series, and the phase rule. A total of 100 different alloy compositions was arc-melted and studied in the as-cast condition metallographically and by X-ray diffraction. Specimens of each of these compositions were heat-treated at 2680, 2530, and 2020°C for 1, 2, and 4 hr, respectively. Those which were treated at 2020 were given a preliminary homogenization treatment at 2500°C for 1 hr. Specimens of 25 alloys were heat-treated at 1200o C for 168 hr. Solidus temperature measurements were made by the detection of incipient melting in eighteen alloy compositions. The metallographic and X-ray diffraction results are summarized in Table I. Graphically, this information appears in the isothermal plots of Figs. 2 and 3. Within the accuracy of the experimental methods, two such plots are sufficient to locate these data, since the results for 1200°C were similar to 2020 and those at 2530 resembled 2680

Jan 1, 1962

By D. B. Hobbs, H. O. Burrows, T. D. Stay

Aluminum which has lost its original identity as to source may be considered as secondary. This would include scrap originating in the fabrication of aluminum, which is not consumed at the plant of fabrication, and all material resulting from fabrication, which has lost its original identity regardless of whether it be consumed at the plant of fabrication or not. In general, secondary aluminum may be divided into two classes, commercially pure and alloyed. The chief impurities found in commercially pure aluminum are copper, iron, titanium and silicon; while in aluminum alloys, copper, iron, titanium, silicon, zinc, manganese, magnesium, nickel, or tin, may be present in varying proportions. Occasionally lead and antimony are found in secondary aluminurn alloys, especially if the alloy results from remelting vender's automotive scrap. Such alloyed elements as are found in the scrap cannot be removed on remelting. In this, the remelting of secondary aluminum differs from the smelting of secondary copper or most other secondary metals. The majority of secondary materials reach the consumer in the form of remelt ingot or remelt No. 12 ingot. This ingot varies greatly in quality, depending upon the source of the material, and the manner in which it is refined and blended. The principal differences between primary and secondary ingot are: 1. The composition of secondary ingot may be more or less inclcfinite. 2. Secondary ingot may contain more dross and oxide. Secondary ingot may, however, be used successfully in a great itiany products. Relation of Primary Production to Secondary Production Table 1, compiled from data published by The Ameriran Metal Market, gives an approxirnatc idea of the relation of primary to srcondary production. Information obtained from other sources leads the authors to believe that the figures for secondary production are somewhat low.

By Charles E. Heinrichs

There arc still ample reserves of phosphate in Florida and Tennessee, but the richest low-cost areas have been exhausted. The miners, by the introduction of more efficient equipment, have succeeded in preventing material increases in production costs. Further mechanical improvements could not be expected to keep up with the factors tending to increase costs. While the conventional phosphate "washers" are capable of recovering practically all of the plus 1.5-mm. phosphate from the matrix, approximately 50 per cent of the phosphate values are in the minus 1.5-mm. sizes. Flotation now affords an economical and efficient means for recovering the fine ( — 1.5 mm.) phosphate formerly discarded to waste dumps. Through the reclamation of dumps and recovery from current washer wastes, flotation has doubled the reserves of Florida and Tennessee. By doubling recoveries from the matrix, flotation reduces capital investment requirement and substantially reduces production costs. It definitely improves the grade of the total production and provides a flexibility of operation that cannot be obtained by any other known means.

Jan 1, 1934

Human progress has a visible material phase, easily discernible, that is expressed in the standard of living. This material phase, however, is only the outward expression of a spiritual or mental phase that acts as a driving force in making humanity improve both its outlook and its mode of living. The instrument of progress is the human brain. Under the urge of spiritual drive, the brain acts as a focal point to utilize the forces of nature and put them to work for the benefit of mankind. Besides intelligence, which is an innate quality, the tools of the human brain are knowledge, experience, training, initiative, and skill. Given sufficient intelligence, the human brain can make an amazing amount of progress, provided it is supplied with an adequate spiritual and moral urge and a good technical background. It is the role of education to sup- ply such a background. The material phase of human progress proceeds on a series of parallel fronts, all of them interdependent to some extent (Fig. 7). The rise of the standard of living, dependent as it is upon the manufacture and mass distribution of goods, is based essentially upon the development and utilization of the material resources of a country or land area. This development involves the extraction of mineral and organic products from Mother Earth, their transportation to manufacturing centers, their transformation into finished goods and their dis-

Jan 1, 1950

By George W. Mitchell

THE property of Eureka Corp. Ltd. is located in the approximate geographic center of Nevada, 2 miles from Eureka, the county seat. The great sources of power, the Colorado, Snake, and Salmon Rivers and the rivers of northern California, are 300 to 500 miles distant, and no lines serve areas closer than 150 miles. Fuel for diesel and steam generation is available in Utah, 300 to 400 miles to the east. Eureka's railhead is 80 miles north where two trunk lines cross the county. A spur line serves Ely, 77 miles east. Good highways connect Eureka to the railheads. Activity in the Eureka mining district began in the early 1870's. The oxidized high grade lead-sil-ver-gold ore terminated against the footwall of the Ruby Hill fault, and in 1890 the main operations ceased. In 1938 Eureka Corp. Ltd. discovered ore in the hanging wall of the fault by diamond drilling. The history of Eureka in the late 1800's indicates that there was some water at 600 to 800 ft in the old workings, probably accumulations above the water table which did not seriously interfere with mining operations. Both the Locan and Richmond shafts were sunk to a level below the table, but apparently the only serious difficulty with water occurred in the Locan. The steam pump used when the last work was done on the 1200 level in 1923, many years after exhaustion of the main orebodies, is still installed on the Locan 900 level. The capacity was about 500 gpm, lifting 750 ft to the 100 level, which connected with the surface. In addition to this. bailers were used to keep the 1200 level free of water. It is said that pumping in 1923 lowered the water in the Holly shaft, about a mile and a half away, but this seems doubtful. The pumping was of short duration because no ore was found. When work at the new Fad shaft was started in 1941 Eureka Corp. Ltd. engineers were fully aware of the probability of encountering water in large volume. Their primary exploration and development had to be carried on at the 2250 level. The first water was encountered at 300 ft. This was undoubtedly surface drainage in the bedding of the Pogonip limestone and was less than 100 gpm. The fractured, loose Hamburg dolomite at the water table was not well cemented, and relatively little water, 300 gpm, percolated through it with difficulty. At 1350 ft well-cemented dolomite containing some open fractures was encountered. These fractures produced the first water of consequence, 750 gpm. At 1700 ft the volume was 1000 gpm increasing to the maximum during shaft sinking, 1600 gpm, at the 2000 level. Secret Canyon shale, a dry formation, was entered at 2100 ft, where a concrete water ring was placed to catch all of the water. The volume decreased rapidly to a constant flow of 1200 gpm. Below 2100 ft the shaft and stations remained in the shale and water was not a problem. Several faults of moderate displacement, including the reverse Martin fault, had been intersected during the traversing of 1000 ft of wet Hamburg, but no undue quantities of water were encountered. Observations in the diamond drill holes in the ore zone area showed a rapid lowering of the water table. The shaft was flooded when it left the dry shale and entered the water-bearing Eldorado dolomite on the 2250 level, crossing a fissure which paralleled the Martin fault. High pressure water doubled the volume then being pumped. Pipe failure through a water door bulkhead was a contributing factor. Immediately following this flooding in March 1948 preparations were made to recover the shaft as rapidly as possible by increasing power and pump capacities as needed. Measurements before flooding indicated the water could be lowered at a fast rate. However, the water table did not recede as rapidly as expected and volumes required to lower the water in the shaft were higher. Obviously the size of the main water channel on the 2250 level was increasing because of erosion, allowing greater volumes to enter the workings and draining beyond the cone originally being drained during shaft sinking. Eroded material was being deposited in the shaft below the 2250 level in serious proportions. In December 1948 a second flooding of the Fad shaft was allowed for the purpose of reassessing existing conditions and studying alternate methods of attack. The detailed geology of the Eureka mining district, see Fig. 1, has been described during the past 75 years by many geologists.' Only the general features and those which seem to affect the drainage problem will be discussed. The old ore zone, mined between 1870 and 1890, is located in a wedge-shaped block of Eldorado dolomite between the footwall of the Ruby Hill fault and the underlying Prospect Mountain quartzite, see Fig. 2. Production of high grade oxidized lead ore containing high values in gold and silver has been variously estimated at $50 to $90 million. The tonnage mined was probably close to 1,500,000, nearly all of which was found above the water table. The new ore, discovered by diamond drilling in the hanging wall of the Ruby Hill fault, is a flat-

Jan 1, 1954

By J. R. Vilelia

IN accordance with the custom of this society, we are gathered here, as we have every year since 1924, to honor the memory of the eminent American metallurgist and teacher, Professor Henry Marion Howe. Unlike many of the distinguished metallurgists who have preceded me as a Howe lecturer, I cannot bring to you reminiscences of his personality, for it was not my privilege to be associated with Professor Howe, or to be directly one of his students. Yet, Professor Howe and Professor Albert Sauveur, through the medium of their books, were my first teachers of metallography, as they have been of almost all American metallurgists of my generation. As a teacher, and for many years the acknowledged leader of American metallurgists, he exercised a profound influence in the growth of our science and was held in honor by the men of science of his time. I can speak no words of technical appreciation that will add luster to his fame, for by his prophetic vision, his teachings, and his researches he stands among the immortals in the memory of all metallurgists. In 1926, the third Howe Memorial Lecture was presented by Professor William Campbell' of Columbia University, who entitled it "Twenty-Five Years of Metallography." He took as a starting date for his chronology the turn of the century, which coincided with his arrival from England to work in association with Howe at the Columbia School of Mines. In that informative lecture Professor Campbell enumerated the important advances in metallography achieved during the first quarter of the century, and, it now appears, may have established the custom of reviewing such progress every twenty-five years. The scope of Professor Campbell's lecture was as broad as his metallurgical knowledge, for it embraced a wide portion of the field of metallography, both ferrous and nonferrous. Twenty-five years later, the Howe Memorial Lecture Committee saw fit to assign to me the honor of writing a lecture that would commemorate the work of Henry Marion Howe and would at the same time constitute the 25th anniversary of the lecture by Professor Campbell. The Committee suggested that this lecture might properly be called "Twenty-Five More Years of Metallography," a suggestion that I have adopted. I must confess, however, that I have not followed the precedent established by Campbell and have narrowed the scope of this lecture to an appraisal of those achievements which in my opinion have contributed most to the progress of microscopical metallography during the past twenty-five years. Progress in Metallography The metallographic methods most widely used today, with the exception of the electron microscope, were firmly established more than twenty-five years ago. In general, our specimens were prepared for microscopic examination in those days in much the same manner as they are today. It is true that new details of technique have been introduced from time to time, and that superior equipment is available today, but on the whole, these improvements have been in the nature of refinements, often a matter of personal preference, and none can be considered essential to the attainment of the ultimate goal of the art and science of metallography, which is to reveal the structure of metallic specimens with unequivocal clarity so that they may be interpreted correctly. Mechanical metallographic polishing, which was the only method available in 1926, is still universally practiced and still consists of abrading the metallic specimen with a series of abrasives of increasing fineness until a specular surface is attained. We have now the alternative method of electropolishing, but it is not widely used because, except in a few special cases, its results are inferior to those of competent mechanical polishing. Likewise, most of the etching reagents preferred today were in common use more than twenty-five years ago and were applied in the same manner as they are today. Valuable improvements have been made in the optical and mechanical performance of metallurgical microscopes, but there was no dearth in those days of excellent instruments equipped with achromatic and apochromatic objectives capable of yielding micrographs comparable in quality with the best that we can make today. In fact, it would be a difficult task for any metallographer today to make optical micrographs at magnifications in excess of 3000 diameters that would surpass those made by Lucas more than twenty-five years ago. One of these is shown in Fig. 1. Yet, it is unquestionable that on the whole, the micrographs appearing in the metallurgical literature today are vastly superior to those

Jan 1, 1952

By Charles T. Holland

In connection with the problems of bumps in coal mines, much has been written concerning the manner in which roof action and methods of mining enter into the pressure effects observed but little has been written upon the relationship between the physical properties of coal and associated rocks and the cause of bumps. The question of the strength of bituminous coal, of its elasticity, and the energy it can absorb and store has been neglected to a considerable extent in connection with this problem. It is generally agreed that one of the necessary conditions for bumps is a strong coal.' Therefore, since the strength of coal is an important factor, a study of this property should be made. several investigators have conducted laboratory experiments upon the strength of coal, using small cubical or rectangular test pieces. An attempt will not be made to go into all of these investigations, but they are briefly summarized in Table I. Experiments of the U. S. Bureau of Mines and of Lawall and Holland (pp. 27 and 34 of ref. 9), however, indicate that regardless of whether the coal is a soft and weak semihituminous (Pocahontas No 3) or a hard and strong bituminous (Stockton) coal, the maximum ultimate unit stress developed in laboratory tests is higher in small cubes than in larger cubes of the Same coal.

Jan 1, 1942

By Charles T. Holland

In connection with the problems of bumps in coal mines, much has been written concerning the manner in which roof action and methods of mining enter into the pressure effects observed but little has been written upon the relationship between the physical properties of coal and associated rocks and the cause of bumps. The question of the strength of bituminous coal, of its elasticity, and the energy it can absorb and store has been neglected to a considerable extent in connection with this problem. It is generally agreed that one of the necessary conditions for bumps is a strong coal.' Therefore, since the strength of coal is an important factor, a study of this property should be made. several investigators have conducted laboratory experiments upon the strength of coal, using small cubical or rectangular test pieces. An attempt will not be made to go into all of these investigations, but they are briefly summarized in Table I. Experiments of the U. S. Bureau of Mines and of Lawall and Holland (pp. 27 and 34 of ref. 9), however, indicate that regardless of whether the coal is a soft and weak semihituminous (Pocahontas No 3) or a hard and strong bituminous (Stockton) coal, the maximum ultimate unit stress developed in laboratory tests is higher in small cubes than in larger cubes of the Same coal.

Jan 1, 1942