Search Documents

By Nicholas J. Grant, David S. Bloom

An investigation of the Cr-Ni system has revealed that there exists a eutectoid transformation at about 1180°C. 'The transformation in chromium implied by the eutectoid reaction was detected at about 100°C below its melting point. Associated with the eutectoid transformation, a metastable transition structure has been found. THE Cr-Ni phase diagram is shown in current literature to be a simple eutectic system in which the high chromium end of the diagram is incompletely determined, Fig. 1. The last investigation of this system was undertaken in 1936.' Because of limitations in metal purity, especially of chromium, and temperature measuring techniques, the diagram should be accepted with some reservations, as was indicated by Hansen.V or examwle.-, the wresence of the compound Cr²Ni, with a tetragonal structure," remains unverified and incompatible with the simple eutectic diagram. The work reported here began because of discrepancies that appeared in experimental studies in the binary alloys Cr-Ni and in the ternary system Cr-Mo-Ni. The existing binary Cr-Ni diagram failed to provide a complete explanation of observations made by microscope, X-ray, and thermal analyses. Experimental Methods The materials employed were of a higher degree of purity than were available to previous investigators. The Mond nickel used had a nominal purity of 99.87 pct, while the electrolytic chromium analyzed 99.03 pct with the major impurity being 0.5 to 0.7 pct oxygen with some iron. All alloys were melted in a vacuum furnace to remove dissolved gases, sufficient carbon was added to the charge to combine with all the oxygen as CO. Final analysis determined the carbon as about 0.02 pct and the oxygen around 0.06 pct or slightly more. Stabilized zirconia crucibles and thermocouple protection tips were used throughout and contributed no detectable impurity to the melts, as long as the oxygen in the chromium was kept low. Heats averaged about 250 g, which permitted about 2 in. of the thermocouple protection tips to be submerged. The temperature drop across the thermocouple protection tip was determined to be about 3°C, a minor source of error. The alloys, after removal from the vacuum furnace, were placed in a furnace operating in a purified argon atmosphere for the thermal analyses. An- nealed wolfram-molybdenum thermocouples provided the primary means of temperature determination, though a Pt-Pt-10 pct Rh couple was employed for a check when possible. A sensitive, high-speed Leeds and Northrup Speedomax recording potentiometer indicated the thermocouple output. X-ray diffraction patterns were obtained primarily on a Norelco unit, which permitted diffraction angles only up to 45" (28 = 90"). In general, either rotated or stationary solid samples were used, because it later evolved that many samples were susceptible to transformation resulting from the cold working involved in pulverizing. It was also noted that rotating a sample sometimes suppressed weak lines, so, usually, samples were not rotated. Later a high temperature camera was adapted for use at temperatures up to 1400 °C on the Norelco unit utilizing both solid and powdered samples. Unless otherwise noted, all X-ray patterns were made with a chromium tube and a vanadium filter. Further-

Jan 1, 1952

By David L. Riley

Organization The Foundling Years - 1901-1921 Two events that occurred in the decade of the 1870's have had far- reaching effects upon the petroleum industry in the U. S. and formed a basis for the birth and growth of the petroleum engineering profession. In 187 1 a group of mining engineers banded together to form the American Institute of Mining Engineers "to promote the arts and sciences connected with the economic production of the useful minerals and metals and the welfare of those employed in these industries by all lawful means". Although it was to be 30 years before an event in Jefferson County, Tex., would cause petroleum to come into prominence as the world's principal source of energy, the founding of AIME provided an organization through which the application of engineering to the recovery of petroleum and natural gas could be developed. In 1875, a Pennsylvania judge who was called upon to make a decision for which there was no precedent reasoned that oil and gas were like wild game - they belong to the man who can reduce them to possession. His decision sired the "rule of capture", which stated that a landowner possesses the oil produced from his well, even though it might have come from beneath his neighbor's land. This interpretation prevailed for more than half a century, during which time gold-rush tactics were employed in the drilling and production of many oil fields in the U. S. The resulting overproduction and tremendous waste led to a virtual economic collapse of the U. S. petroleum industry by the early 1930's. To bring these malpractices under orderly control, proration and conservation policies were developed, and petroleum engineering became the medium through which they were devised and implemented. At the turn of the 20th Century, more than 90 percent of this country's oil production came from the East, but the picture changed with dramatic suddenness on Jan. 10, 1901. Captain Anthony F. Lucas, an Austrian mining engineer, had noticed concentrations of oil and gas near salt domes during mining operations on the Louisiana Gulf Coast. In 1899 he leased a low mound near Beaumont, Tex., began drilling, and after almost 2 years of intermittent operations, brought in the famous "Lucas Gusher"

Jan 1, 1971

By Edmund C. Pechin

I REGRET that I am unable to present this subject in definite form and detail. All I shall attempt at this meeting is to lay before you some curious facts, the bearings and explanations of which must be reserved for future consideration. I hope before the next meeting to have carried experiments far enough to furnish a more important contribution to the science of iron metallurgy. The Wickersham process consists in the introduction into the molten metal, as it runs from the furnace, of air from the hot blast. Mr. Samuel Wickersham is the originator of the plan, as applied in practice, although Mr. Martien had the idea a long time ago, and, I believe, went to England about it. But at that time Mr. Bessemer was coming before the public with his invention, which engrossed the attention of iron-masters, and Mr. Martien accomplished nothing. The principal difficulty in our experiments at Dunbar was to get a practicable runner or trough, through which the molten metal should pass, and in which it should be exposed to the action of the Mast. The runner we used was ten feet long, and perforated on the sides to permit the entrance of the air-currents. When we used a cast-iron and fire-clay runner, the heat was so great that before we were more than half done with a run, the lower part of the runner was melted, and we had a magnificent Fourth of July display of fireworks until the blast was shut off. We had to abandon fire clay. The runner with which we have had the best success is made of wrong- ht-iron tubes, 29 inches in diameter, attached to a wrought-iron frame, and lined with a mixture of crushed conglornerate (quartz) and a little fire clay to give it cohesion. The wrought-iron shell curves inward over the upper edges, so as to catch and throw back into the current the flying sparks and particles of metal thrown out by ebullition. With this we have been able to run 12 to 14 tons at a heat with great ease. Mr. Wickersham has since prepared this material (pounded quartz) into a shaped brick or tile, with the necessary perforations for the passage of the air, which promises to answer every requirement for steady working. As regards the improvement in the quality of the iron, there seems to be no question. A large number of practical tests were made in

By Ernest Stütz

The problem of increasing blast-furnace efficiency through diminution of flue-dust production while operating with burdens consisting largely of fine ores has of recent years attracted the attention of metallurgists, whether directly or indirectly interested in the economies of iron smelting, and the various methods evolved from theory or practice have been submitted to wide discussion. After the very thorough and, at that time, exhaustive view of the whole subject, which was afforded to the industry by the meeting of this Institute in February, 1912, the subject was again taken up at the meeting of the Verein deutscher Eisenh?ttenleute at D?sseldorf in December, 1912. While American and German conditions are not entirely identical, it may be of interest to give here the words of the gentleman summing up the discussion at the Diisseldorf meeting: " The chief advantage offered by the use of briquettes lies in the fact that disturbances in the furnace, caused mostly by the presence of fine ores in the burden, are avoided, and that blast pressure can be considerably reduced. The resulting economies cannot be overrated, as, with lower blast consumption per ton of product, the installation will be able to take care of increased production. In consequence of lower pressure and speed of blast, heat is more efficiently utilized, flue gas temperature is lowered, and coke particles are less liable to be carried along with the flue dust, of which considerably less is produced. Finally, by increased regularity of operation and higher temperature in the lower parts of the furnace, the quality of the product is improved. The question of briquetting iron ores has grown to be one of the most important in the iron industry, and it is not any more a question of what is the cost of briquetting a ton of ore, but what, in using ore briquettes, is the cost of production of a ton of iron." Dr. A. Weiskopf, of Hannover, admirably condenses in these words

Jan 1, 1914

By J. A. Wilcox

A NEW LINE of specialists has arisen as a result of the trend toward labor socialization and collectivism in all branches of industry. These men are the ones who will govern the destiny of many companies and the labor policy of our government in coming years. They must be men of integrity and of rather exceptional qualifications; men who can foresee the trend of labor relations with business, and who are willing to sacrifice the immediate fruits of technical training for manual labor and study. They must take their place in industry, not with the idea of following the orthodox line of advancement, but knowing that they must stay at the bottom until they have learned to understand the viewpoints, the work, the advantages and the disadvantages of each classification of labor. They must not be of a radical nature or become easily biased, and they must study. You will say I am looking for a superman and in one sense that is true, but the business man and our government are both in the market even now for this type of man, and with the proper training and background, many of our young technicians can readily enter this field of work.

Jan 1, 1942

By E. Klar, A. B. Michael

Differences in the electrical conductivities of copper powder sintered under reducing, selectively oxidizing, and neutral atmospheres are related to impurities in solution or as precipitated oxides. The precipitation of impurities as oxides during sintering in nitrogen is proposed for maximizing the conductivity of sintered copper. Conductivity equations for two-phase systems are summarized. Selected equations are applied to porous sintered copper and composite structures. A recent review of the influence of impurities on the electrical conductivity of copper by Gregory et al.1 emphasized that an impurity in solid solution has a much more pronounced effect on reducing the electrical conductivity than when present partly or wholly as a second phase. When impurities in solid solution can be precipitated as oxides, the copper is purified with respect to these elements and the conductivity is increased. Cast and wrought copper, therefore, frequently contain an intentional residual oxygen concentration to oxidize and precipitate impurities less noble than copper. Copper powders generally also contain impurities which can contribute to a reduction in the electrical conductivity of the sintered material. The most deleterious impurities commonly found in commercial copper powders which markedly decrease the electrical conductivity when in solid solution but which can be precipitated as oxides include iron, tin, antimony, arsenic, cobalt, and nickel. In addition to impurities, porosity in sintered copper also contributes to a reduction in the electrical conductivity. The work reported herein discusses the influence of impurities, sintering atmospheres, and porosity on the electrical conductivity of sintered copper. These are important factors for controlling the electrical conductivity of materials such as sintered copper electrical contacts. Several publications on the electrical conductivity of sintered copper and composite materials with random pores or obstacles have incorrectly considered the conductivity to be proportional to the volume fraction of conducting material. However, analyses and equations have been proposed, the earliest of which is perhaps Lord Raleigh's of 1892,' which more accurately describe the conductivity of two-phase systems. These equations which in many cases allow one to closely estimate the electrical conductivity of porous sintered materials and two-phase composites will be reviewed and related to the measured electrical conductivity of sintered copper, copper-graphite. and Ag-W composites. INFLUENCE OF IMPURITIES AND OXIDIZING, REDUCING, AND NEUTRAL ATMOSPHERES Zone-Melted and Leveled Copper. The electrical conductivities of an electrolytic copper and a lower-purity compacting grade of copper powder after consecutive treatments in reducing or selectively oxidizing atmospheres are compared in Fig. 1. The powder and drillings from the electrolytic copper ingot were melted and solidified in a graphite crucible under hydrogen. The vertical zone leveling technique of multiple passes in opposite directions was used to obtain a uniform distribution of impurities. The electrical conductivity was measured on machined specimens 3 by 0.10 in. diam of the zone-leveled material and after the same specimens were consecutively treated as follows: 1) heating in hydrogen at 1600°F for 3 hr; 2) heating in air in a sealed tube so that 0.04 pct 0 was introduced; heating was started at 1000°F for 1 hr and continued at 1800°F for 8 hr; the stepwise diffusion treatment was used to avoid loss of copper due to evaporation of copper oxide at higher temperatures; and 3) final heating in hydrogen at 1600°F for 3 hr. A L&N Kelvin Bridge, type 4306, and a test fixture with knife edges 2 in. apart were used to measure the room-temperature conductivity with an estimated accuracy of ±0.5 pct. In all cases the conductivity of the electrolytic copper was approximately 100 pct of IACS. The conductivity of the impure copper was 80 pct of IACS both in the cast state and after heating in hydrogen. However, after the heating in air, the conductivity of the impure material was 100 pct IACS. After again heating in hydrogen, the electrical conductivity decreased to 60 pct of IACS. This decrease is attributed both to the dissolution of impurities and observed intergranular cracks due to the phenomenon of hydrogen embrittle-ment in copper. These data show that the electrical conductivity of commercial copper as represented by a compacting type powder can be increased significantly by the precipitation of impurities as oxides through heat treatment in an oxidizing atmosphere. Sintered Copper Powder. A commercial compacting type of copper powder pressed to various densities was sintered either in nitrogen, dissociated ammonia, or dissociated ammonia followed by a selectively oxidizing atmosphere of air in sealed Vycor tubes so that 0.06 pct O was added to the material. The electrical conductivity was measured perpendicular to the pressing direction on as-sintered specimens of approximately 3 by 0.25 by 0.15 in. The fully dense material was obtained by zone melting and leveling

Jan 1, 1969

By Roswell Johnson

THE Manual of the Oil and Gas Industry, under the Revenue Act of 1918, published by the Treasury Department for the guidance of oil companies in preparing their estimates of future recoverable oil for the purpose of calculating depletion, gives the first large public collection of comparative decline curves for the whole country. It is a matter of both scientific and practical interest to so arrange these data that the pools can be readily compared. There are certain difficulties in such a comparison, however: 1. The economic limit varies from 50 to 2000 bbl. a year in different pools taken. (2) Because of this variation in economic limit, the range of data shown makes comparison possible only for wells of intermediate size. In order to be as inclusive as possible, I have taken as an expression of the rate of decline the amount of oil produced in the period during which a well drops from 3000 to 2000 bbl. a year.. No period of smaller production could be used because of the high economic limit in California; and no period of larger production and yet include the small well areas of the Appalachian. As it is, the Lima-Indiana wells are excluded. In a few instances, curves were extrapolated to obtain the reading, where the curve seemed regular enough to warrant it. In general, the amount of oil, in barrels, produced while a well declined from 3000 bbl. to 2000 bbl. a year is shown in Table 1.

Jan 1, 1920

By R. H. Johnson

The Manual of the Oil and Gas Industry, under the Revenue Act of 1918, published by the Treasury Department for the guidance of oil companies in preparing their estimates of future recoverable oil for the purpose of calculating depletion, gives the first large public collection of comparative decline curves for the whole country. It is a matter of both scientific and practical interest to so arrange these data that the pools can be readily compared. There are certain difficulties in such a comparison, however: (1) The economic limit varies from 50 to 2000 bbl. a year in different pools taken. (2) Because of this variation in economic limit, the range of data shown makes comparison possible only for wells of intermediate size. In order to be as inclusive as possible, I have taken as an expression of the rate of decline the amount of oil produced in the period during which a well drops from 3000 to 2000 bbl. a year. No period of smaller production could be used because of the high economic limit in California; and no period of larger production and yet include the small well areas of the Appalachian. As it is, the Lima-Indiana wells are excluded. In a few instances, curves were extrapolated to obtain the reading, where the curve seemed regular enough to warrant it. In general, the amount of oil, in barrels, produced while a well declined from 3000 bbl. to 2000 bbl. a year is shown in Table 1.

Jan 1, 1921

By Edmund C. Pechin

I REGRET that I am unable to present this subject in definite form and detail. All I shall attempt at this meeting is to lay before you some curious facts, the bearings and explanations of which must be reserved for future consideration. I hope before the next meeting to have carried experiments far enough to furnish a more important contribution to the science of iron metallurgy. The Wickersham process consists in the introduction into the molten metal, as it runs from the furnace, of air from the hot blast. Mr. Samuel Wickersham is the originator of the plan, as applied in practice, although Mr. Martien had the idea a long time ago, and, I believe, .went to England about it. But at that time Mr. Bessemer was coming before the public with his invention, which engrossed the attention of iron-masters, and Mr. Martien accomplished nothing. The principal difficulty in our experiments at Dunbar was to get a practicable runner or trough, through which the molten metal should pass, and in which it should be exposed to the action of the blast. The runner we used was ten feet long, and perforated on the sides to permit the entrance of the air-currents. When we used a cast-iron and fire-clay runner, the heat was so great that before we were more than half done with a run, the lower part of the runner was melted, and we had a magnificent Fourth of July display of fireworks until the blast was shut off. We had to abandon fire clay. The runner with which we have had the best success ,is made of wrought-iron tubes, 2 1/2 inches in diameter, attached to a wrought-iron frame, and lined with a mixture of crushed conglomerate (quartz) and a little fire clay to give it cohesion. The wrought-iron shell curves inward over the upper edges, so as to catch and throw back into the current the flying sparks and particles of metal thrown out by ebullition. With this we have been able to run 12 to 14 tons at a heat with great ease. Mr. Wickersham has since prepared this material (pounded quartz) into a shaped brick or tile, with the necessary perforations for the passage of the air, which promises to answer every requirement for steady working. As regards the improvement in the quality of the iron, there seems to be no question. A large number of practical tests were made in

Jan 1, 1873

By G. B. Pryde

IN laying out a new mine, provision should be made for the ultimate recovery of as much coal in any given bed as is consistent with safety and economic mining. Though each mining district, if not each individual mine, has problems that make the adoption of any hard and fast rule impossible, certain basic principles are adapted to practically all conditions. One of the most vital is the provision for barrier pillars of ample dimensions to protect all haulage and permanent airways during the life of the property. Where conditions permit, room or butt entries should be driven on the strike or slightly to the raise and rooms turned at right angles to said entries. The width of rooms and room pillars is governed by conditions prevailing in the mines under consideration. A safe rule is: In advancing, extract not more than 25 to 35 per cent. of the entire seam; in exceptionally thick seams, considerably less than 25 per cent. should be taken. Rooms usually vary in length from 250 to 350 ft. (76 to 106 m.) with a barrier pillar of not less than 80 ft. between the last crosscut in rooms, and entry and room crosscuts should be driven on sights; room crosscuts should be driven at right angles to the direction of the rooms. In mines under excessively heavy cover or where roof conditions are bad, rooms should be driven narrow and a barrier pillar left at every fifth to tenth room. This barrier should be of such dimensions that one or more rooms, with pillars of usual dimensions, may be turned through it when the barrier is no longer required. Two of the advantages of such a barrier are the protection of the panel against peaking of roof load during pillar extraction and the easy closing of the entry in case of fire.

Jan 2, 1921

By E. A. Cappelen Smith

FOR distinguished service in the art of hydrometallurgy, the Mining and Metallurgical Society of America presented its gold medal to E. A. Cappelen Smith, at a dinner held in the Hotel Commodore, New York, on Nov.' 10, 1920. Prof. Waldemar Lindgren, president of the society, in giving the medal, said: "By the advancement of the science of hydrometallurgy, by the construction of plants on a scale audacious in their conception, by the successful overcoming of all sorts of difficulties, you have placed your name among those who occupy the very front rank among the hydrometallurgists. In recognition of this distinguished contribution to the science of metallurgy, the Mining and Metallurgical Society of America now awards you its gold medal."

Jan 1, 1920

By S. K. Tarby, W. O. Philbrook

The rate of FeO and MnO reduction from silicate and aluminate slags by carbon-saturated iron is dependent on both slag composition and temperature. Owing to variable stirring rules during- the course of reaction, the reduction processes occur in two stages in stationary graphite crucibles. In the first stage the slirring caused by CO evolution results in forced convection conditions in the slag. As the boiling action subsides during reduction, the flow conditions within the system become those defined by natural convection. Analysis of the data by an unsteady-state penetration model indicates that the rate of reduction is controlled by the rate of cocur-rent flow of' cations and anions from the bulk slag to the interface during both stages of reduction. The hearth reactions of the blast furnace have been extensively investigated from the viewpoint of equilibrium by deductions from controlled laboratory experiments. However, the literature contains relatively few studies that have been directed toward the area of slag-metal reaction kinetics, and the majority of these have been concerned with the rate and mechanism of sulfur transfer between iron and slag. More recently, attention has turned to the kinetic factors in the reduction of oxides from liquid slags. One of the first investigations in this field was conducted by Dancy1 on the reduction of pure liquid FeO and pure liquid Fe3O4 by carbon-saturated iron. The integrated form of the rate equation indicated that the reduction of FeO was of the first order up to 80 pct reduction. Over the initial 30 pct of reduction, the magnetite reaction was also interpreted as a first-order process. The rates of reaction were extremely rapid as indicated by a 30 pct reduction of the liquid magnetite in a time interval of about 1 to 2 sec. Phil-brook and irkbbride' studied the reduction of FeO from a lime-alumina-silica slag by carbon-saturated iron and solid graphite in stationary crucible assemblies. With the use of the differential form of the rate equation, the rate of the reduction reaction was found to be proportional to the second power of the concentration of the reactant FeO for both the slag-metal and slag-graphite reactions. These authors presented a number of comments in an effort to explain the difference between the molecularity of the above reaction and the observed second-order relation. One such argument, recently extended by Wagner,3 was that the rate-limiting step may well be one of transport control. A complete discussion of the proposed mass-transport control mechanism of this reduction reaction will be presented in a later section of this paper. Kinetic studies of the reduction of other oxide species, namely chromous oxide, titania, and silica, have also been reported. McCoy and philbrook4 used rotating crucible assemblies to investigate chromium reduction from Ca0-SiO2-A12O3 slags. First-order kinetic law was obeyed for the slag-metal reduction reaction as determined by the integration method of data analysis. Due to scatter of the data, any dependence of the rate constant on temperature or slag composition was obscured. Concentration-time data for the reduction of titania from blast-furnace type slags under reducing conditions were obtained by Delve, Meyer, and Lander.' The data were too few, however, for a formal kinetic interpretation. Kinetic data for the very slow reaction of silica reduction have been observed by McCoy and Philbrook6 and Fulton and chipman.7 The former experimenters found the reaction-rate constant for silica reduction by carbon-saturated iron to be 20 to 60 times less than the rate constant for chromium reduction. In their work on the reduction of SiO2 in mechanically stirred systems, Fulton and Chipman also found small values for the specific reaction rate and derived a high value for the energy of activation for the reaction. In both of these investigations, the reduction process was assumed to follow first-order behavior. schuhmann8 proposed that the rate-limiting step in this reaction is the diffusion of oxygen from the interface through a boundary-layer film to the bulk metal phase, and Rawling and Elliott9 have reported experimental confirmation of this hypothesis for temperatures below 1600°C. Turkdogan et a1.10 have also concluded that the rate of reduction of silica is a slow process and controlled by the diffusion of oxygen in the metal, but only in the absence of carbon monoxide bubbles at the slag-metal interface. In the presence of bubbles, achieved either by injecting carbon monoxide at the slag-metal interface or by blowing it through the metal and slag, these investigators found a rather rapid reduction of silica which appeared to be controlled by an interfacial reaction involving the de-sorption of silicate ions from the slag-metal interface to the metal phase as silicon and oxygen atoms. In view of the unresolved nature of the kinetics of FeO reduction and the lack of kinetic data for the manganese reaction,

Jan 1, 1968

By Charles L. Mantell, Kurt Straler

The hydrogen reduction of Cr2O3 to chromium metal was found to be feasible at very low water-vapor concentrations, corresponding to dew points of -38° to -24°C, over a temperature range of 1130" to 1490°C. Hydrogen reduction under these conditions was predicted by the calculated equilibrium curves which also indicated that CrzOs is reduced directly to chromium without forming the intermediate oxide, CrO. This reduction path was confirmed by X-ray diffraction analysis. The percent reduction of Cr2O3 at each reaction temperature was constant with time, suggesting an inhibiting effect of water vapor. A small increase in the residual water-vapor concentration of a single temperature, 1490°C, strongly retarded the rate of reduction This effect was expressed by an empim'cal equation which indicated a direct relationship between "distance from equilibrium" and the rate of reduction. me effect of temperature over the range of 1130" to 1490°C was expressed in an Arvhenius plot of log rate vs reciprocal absolute temperature. From this curve the apparent enthalpy of activation was found to be 29,600 cal. Based on the hypothesis that the rate of reductiun is contvolled at the oxide-metal interface, an over-all rate equation consistent with the experimental data and the thery of absolute reaction rates was formulated. A simplification of this expression to an Arrhenius equation was justified by the overriding effect of temperature on the rate of reaction for the minimum water-vapor concentration range. MOST of the metals in Subgroup V1 of the periodic table can be prepared commercially by direct reduction of their oxides by hydrogen or carbon monoxide, at temperatures considerably below the melting points of both the metals and their oxides. Chromium is an exception, being generally reduced from its ore, Cr2O3 . FeO, by silicon in an electric arc furnace which operates above the melting point of the Fe-Cr alloy or above the melting point of chro- mium if a chromium oxide be the starting material. In reduction of chromium oxide by hydrogen, either reduction does not occur at all or the rate of reduction is extremely slow. Theoretical considerations based on the high, exothermic, free energy of formation of Cr2O3 compared to the oxides of the other Subgroup VI metals, molybdenum, tungsten, and uranium, would also suggest a slow rate of reaction and a high activation energy. Interest in the direct gaseous reduction of fine-powdered ores in fluidized beds was considered justification for examination of this reaction. In order to develop a basis for a continuing study of the commercial feasibility of the direct gaseous reduction of chromite, a study of the kinetics of the reduction of Cr2O3 with hydrogen was undertaken. To the authors' knowledge no accurate kinetic data for this reaction have been obtained. Neither has an activation energy been determined nor has an attempt been made to establish a mechanism of reaction. LITERATURE Maier10 compared the data of I. Y. Granaat,6 H. von Wartenburg and S. Aoyama, and G. Grube and M. Flad7 with that derived from calorimetric and ther-modynamic properties for the equilibria for the reduction of Cr2O3 with hydrogen. These results, plotted as the log of the equilibrium constant vs absolute temperature for the reduction of Cr2O3 and the intermediate oxide, CrO, to chromium, show agreement between the differently derived data. In both cases the equilibrium constants were extremely low. Maier showed that, over a temperature range of 1000° to 2000°K, Cr2O3 is more readily reducible than CrO. Granat assumed that CrO was preferentially formed from Cr2o3 above 1100°C. Grube and Flad's analysis of their reaction products in the 895" to 1000°C range indicated the coexistence of only Cr2O3 and chromium. The hydrogen reduction of the other Subgroup VI metals, molybdenum, tungsten, and uranium, shows that reduction of the higher oxide proceeds through all of the intermediate oxides before being reduced to the metal. Since evidence pointed to an anomaly in the reduction behavior of Cr2O3, the authors investigated the reduction path of Cr2Os.to chromium. This was done theoretically with more recently available free-energy data and experimentally by X-ray diffraction analysis. This work reinforces Maier's conclusion.

Jan 1, 1964

By Charles Albert Ashburner

THE stratigraphical geology of the vicinity of Buffalo has always been of great interest on account of its bearing on the origin and history of the Niagara-river gorge, between the Falls and Lake Ontario. Recently, however, the character and thickness of the strata which underlie Buffalo have acquired more practical and economic importance on account of their relation to the possible occurrence of natural gas in commercial quantity near the Niagara river. In a paper presented at the Duluth meeting (l887), on " Petroleum and Natural Gas in New york State" (Trans., xvi., 906), I gave a brief description of the four wells which had been drilled by the Buffalo Cement Company between 1883 and that time. One of these wells is 1305 fret deep; and, at the time that my paper was finally revised for the Transactions (June, 1888), it was still an open question whether the drill in this well had reached the Niagara limestone, or had penetrated the Medina sandstones and shales, which latter are boldly exposed in a number of localities in the district, hut more particularly along the Niagara river in the vicinity of Lewiston and Qneenstown. The difficulty in this geological question at Buffalo has lain in the fact that no reliable determination could be made of the thickness of the strata included between the Corniferous limestone, immediately below which the drilling of the Buffalo gas-wells was commenced, and the Niagara limestone. On the other hand, the strata included between the latter limestone and the middle portion of the Medina sandstones and shales, have been minutely measured and studied in the Niagara gorge below the Falls by many American and European geologists. The first reliable section of these strata was constructed by Professor Eaton, and published in 1824 in his report on the Geological and Agricultural Survey of the District adjoining the Erie Canal. This section, extending from Lake Erie to Lewiston, is complete, with the exception that no thickness is given to the Salina or Onoudaga salt group,

Jan 1, 1889

By M. Katzer, R. Klimpel, J. Sewell

The effect of using selective dispersants as wet grinding aids for ores is demonstrated on laboratory scale batch and continuous grinding equipment. A complete characterization of behavior is performed on a given ore to demonstrate correlations involving torque, % solids, net production rate, and slurry weight and volume loading. The relationship between such laboratory data and industrial scale testing results is very consistent.

Jan 1, 1982

By Charles M. Cooley

In these troubled times free enterprise is maintaining vital molybdenum output, while expanding plant, and bringing in new low grade ore reserves, at Climax, the world's largest known molybdenum deposit. Climax Molybdenum Co. is putting $25 million into additional surface plant facilities and other millions into underground development. The expansion program to be operating by 1954 includes a new mining level, crushing plant, 4000-ft conveyor, milling units, by-products plant, and housing for 198 families. Completion of this program and low grade plant will add 10,000 tons per day to present capacity and several million tons to ore reserves.

Jan 1, 1953

By John A. Mathews

It is twenty years since the writer made his first molybdenum steels and others were making them commercially five years earlier but the prevailing opinion seems to be that molybdenum steels are new; from time to time the daily press speaks of important discoveries in Europe and intimates that American steel makers have much to learn in regard to alloy steels. The earlier experiments were largely confined to the use of relatively high percentages of molybdenum in tool steels and permanent magnet steels. Recent developments deal with the types of alloy structural steels used for airplane, automobile, and other engineering requirements; in these, the molybdenum content is usually less than 1 per cent. The earlier types generally have been unsuccessful commercially, but the newer types of steels are becoming of increasing importance. The war showed our dependence on foreign sources for alloying metals; molybdenum alone is widely distributed in the United States and seemingly abundant. Many deposits are not now of commercial interest, owing to location and relatively small amount of ore available, but other deposits are being developed and a stable source of supply seems well assured. In tool and magnet steels, it was early found that 1 part of molybdenum was equivalent to from 2 to 2.5 parts of tungsten. The permanent magnet steels investigated by Madame Curie,' in 1898, contained from 3.36 to 4.05 per cent. molybdenum; in 1902, Dr. E. L. French and the writer thoroughly tested steels containing from 2.0 to 4.0 per cent. These steels gave satisfactory tests for permanence, but were low in residual density and much more sensitive to hardening than the corresponding tungsten products. We discontinued work with them, therefore, and have no advice that such steels have been used commercially here or abroad. Prior to the development of the Taylor-White process and the modern high-speed steels, air-hardening steels were in general use. These were

Jan 1, 1922

By John A. Mathews

It is twenty years since the writer made his first molybdenum steels and others were making them commercially five years earlier but the prevailing opinion seems to be that molybdenum steels are new; from time to time the daily press speaks of important discoveries in Europe and intimates that American steel makers have much to learn in regard to alloy steels. The earlier experiments were largely confined to the use of relatively high percentages of molybdenum in tool steels and permanent magnet steels. Recent developments deal with the types of alloy structural steels used for airplane, automobile, and other engineering requirements; in these, the molybdenum content is usually less than 1 per cent. The earlier types generally have been unsuccessful commercially, but the newer types of steels are becoming of increasing importance. The war showed our dependence on foreign sources for alloying metals; molybdenum alone is widely distributed in the United States and seemingly abundant. Many deposits are not now of commercial interest, owing to location and relatively small amount of ore available, but other deposits are being developed and a stable source of supply seems well assured. In tool and magnet steels, it was early found that 1 part of molybdenum was equivalent to from 2 to 2.5 parts of tungsten. The permanent magnet steels investigated by Madame Curie,' in 1898, contained from 3.36 to 4.05 per cent. molybdenum; in 1902, Dr. E. L. French and the writer thoroughly tested steels containing from 2.0 to 4.0 per cent. These steels gave satisfactory tests for permanence, but were low in residual density and much more sensitive to hardening than the corresponding tungsten products. We discontinued work with them, therefore, and have no advice that such steels have been used commercially here or abroad. Prior to the development of the Taylor-White process and the modern high-speed steels, air-hardening steels were in general use. These were

Jan 1, 1922

By E. S. Wheeler

The rapid increase in the use of monel metal and malleable nickel in the form of sheet, rod and tube has resulted in a similar increase in the demand for these metals in the form of castings. These castings range in size from small valves and pipe fittings weighing a few ounces to large centrifugal pumps, gate valves and marine propellers, some of the last weighing as much as 24,000 lb. A group of such castings is shown in Fig. 1. A large nickel agitator is shown in Fig. 2. Monel metal castings are widely used in accessories for steam power plants and in a variety of chemical plant equipment where the corrosion resistance, high strength and toughness characteristic of this metal render it particularly valuable. Nickel castings find extensive use in the construction of corrosion-resistant apparatus, and are often used in conjunction with wrought nickel sheet and tube in the fabrication of equipment for handling a variety of chemical and food products, particularly dairy products. In response to this demand for castings, numerous foundries have undertaken the production of castings of these metals and have met with varying degrees of success. The successful production of castings of monel metal and nickel requires careful attention to molding practice, proper melting equipment

Jan 1, 1930