Search Documents

By J. C. Williams

The operations described in this paper are those of the flotation plant of the Valley Forge Cement Co. at Conshohocken, Pa., and concern the use of a particular cationic reagent—namely, DP-243. The role of this reagent in this plant may be better understood by first considering the purpose of beneficiating cement rock in general and the specific problems at the Valley Forge plant. The ultimate purpose of beneficiating cement rock is to obtain a kiln feed of the desired chemical composition in a form suitable for the most efficient kiln operation. The chemical composition is governed by the type of cement to be made. Before government restrictions (the purpose of which is to simplify operations during wartime) limited the types of portland cement a manufacturer is permitted to produce, five principal types of cement were generally recognized by the industry. They are based upon chemical and physical specifications proposed by the American Society for Testing Materials, federal and other governmental agencies, state highway departments, water boards and other users of large quantities of cement. The physical as well as chemical specifications for any particular type of cement necessitate proper proportioning of the major components—that is, the silica, alumina, iron and lime—and it is necessary to establish and maintain definite limits for each in the raw mix. The manufacturer must then prepare a kiln feed of a composition that will yield a final product that will fulfill the desired specification. This step is further complicated for kilns using coal as fuel, by the amount and analysis of the ash introduced. The amount and nature of the dust lost during burning will also affect the composition of the kiln feed. The problem of preparing a kiln feed of the desired chemical composition is not a simple one, and it is the final product that governs the methods used to obtain such a feed. For example, in starting with a material deficient in lime for the mix sought, it may not be sufficient to raise it to the required lime content. The other constituents must also be present in the proper proportions. In some cases, it may be necessary to raise the lime content to a point greatly exceeding that of the final mix, then, by addition of one or more other materials lower in lime, obtain the mix. The rock used at the Valley Forge plant is a metamorphosed argillaceous limestone of the Jacksonburg formation, the same formation as that of the Lehigh Valley cement rock (which occurs approximately 50 miles north), and its oxide composition is similar to that of the latter. The only practical differences between the two are that, as a result of metamorphosis, crystallization of the Valley Forge rock is considerably coarser and it contains less carbon than the Lehigh Valley rock as well as slightly more magnesia in the form of magnesian mica. The calcium carbonate content of the various strata in the Valley Forge quarry ranges from about 65 per cent to over 85 per cent, the average for the entire quarry being somewhat under the requirement for manufacture of cement, which usually is from 75 to 76 per

Jan 1, 1947

By J. C. Williams

THE operations described in this paper are those of the flotation plant of the Valley Forge Cement Co. at Conshohocken, Pa., and concern the use of a particular cationic reagent-namely, DP-243. The role of this reagent in this plant may be better understood by first considering the purpose of beneficiating cement rock in general and the specific problems at the Valley Forge plant. The ultimate purpose of beneficiating cement rock is to obtain a kiln feed of the desired chemical composition in a form suitable for the most efficient kiln operation. The chemical composition is governed by the type of cement to be made. Before government restrictions (the purpose of which is to simplify operations during wartime) limited the types of portland cement a manufacturer is permitted to produce, five principal types of cement were generally recognized by the industry. They are based upon chemical and physical specifications proposed by the American Society for Testing Materials, federal and other governmental agencies, state highway departments, water boards and other users of large quantities of cement. The physical as well as chemical specifications for any particular type of cement necessitate proper proportioning of the major components-that is, the silica, alumina, iron and lime-and it is necessary to establish and maintain definite limits for each in the raw mix. The manufacturer must then prepare a kiln feed of a composition that will yield a final product that will fulfill the desired specification. This step is further complicated for kilns using coal as fuel, by the amount and analysis of the ash introduced. The amount and nature of the dust lost during burning will also affect the composition of the kiln feed. The problem of preparing a kiln feed of the desired chemical composition is not a simple one, and it is the final product that governs the methods used to obtain such a feed. For example, in starting with a material deficient in lime for the mix sought, it may not be sufficient to raise it to the required lime content. The other constituents must also be present in the proper proportions. In some cases, it may be necessary to raise the lime content to a point greatly exceeding that of the final mix, then, by addition of one or more other materials lower in lime, obtain the mix. The rock used at the Valley Forge plant is a metamorphosed argillaceous limestone of the Jacksonburg formation, the same formation as that of the Lehigh Valley cement rock (which occurs approximately 50 miles north), and its oxide composition is similar to that of the latter. The only practical differences between the two are that, as a result of metamorphosis, crystallization of the Valley Forge rock is considerably coarser and it contains less carbon than the Lehigh Valley rock as well as slightly more magnesia in the form of magnesian mica. The calcium carbonate content of the various strata in the Valley Forge quarry ranges from about 65 per cent to over 85 per cent, the average for the entire quarry being somewhat under the requirement for manufacture of cement, which usually is from 75 to 76 per

Jan 1, 1946

By J. C. Williams

The operations described in this paper are those of the flotation plant of the Valley Forge Cement Co. at Conshohocken, Pa., and concern the use of a particular cationic reagent—namely, DP-243. The role of this reagent in this plant may be better understood by first considering the purpose of beneficiating cement rock in general and the specific problems at the Valley Forge plant. The ultimate purpose of beneficiating cement rock is to obtain a kiln feed of the desired chemical composition in a form suitable for the most efficient kiln operation. The chemical composition is governed by the type of cement to be made. Before government restrictions (the purpose of which is to simplify operations during wartime) limited the types of portland cement a manufacturer is permitted to produce, five principal types of cement were generally recognized by the industry. They are based upon chemical and physical specifications proposed by the American Society for Testing Materials, federal and other governmental agencies, state highway departments, water boards and other users of large quantities of cement. The physical as well as chemical specifications for any particular type of cement necessitate proper proportioning of the major components—that is, the silica, alumina, iron and lime—and it is necessary to establish and maintain definite limits for each in the raw mix. The manufacturer must then prepare a kiln feed of a composition that will yield a final product that will fulfill the desired specification. This step is further complicated for kilns using coal as fuel, by the amount and analysis of the ash introduced. The amount and nature of the dust lost during burning will also affect the composition of the kiln feed. The problem of preparing a kiln feed of the desired chemical composition is not a simple one, and it is the final product that governs the methods used to obtain such a feed. For example, in starting with a material deficient in lime for the mix sought, it may not be sufficient to raise it to the required lime content. The other constituents must also be present in the proper proportions. In some cases, it may be necessary to raise the lime content to a point greatly exceeding that of the final mix, then, by addition of one or more other materials lower in lime, obtain the mix. The rock used at the Valley Forge plant is a metamorphosed argillaceous limestone of the Jacksonburg formation, the same formation as that of the Lehigh Valley cement rock (which occurs approximately 50 miles north), and its oxide composition is similar to that of the latter. The only practical differences between the two are that, as a result of metamorphosis, crystallization of the Valley Forge rock is considerably coarser and it contains less carbon than the Lehigh Valley rock as well as slightly more magnesia in the form of magnesian mica. The calcium carbonate content of the various strata in the Valley Forge quarry ranges from about 65 per cent to over 85 per cent, the average for the entire quarry being somewhat under the requirement for manufacture of cement, which usually is from 75 to 76 per

Jan 1, 1947

Jan 1, 1911

By C. E. Shoenfelt

There was a notable decrease in drilling operations in 1940 in all of the Rocky Mountain states except Montana, where the two large fields on the Canadian border, Cut Bank and Kevin-Sunburst, were espe-cially active. The expanding markets for Montana natural gas made necessary the more intensive development of such fields as Rowdoin, Cedar Creek and Devon. While there were no important oil and gas discoveries in 1940 in any of the Rocky Mountain states, a few small pools were opened, which may constitute separate areas but may prove with later development to be extensions of old fields. Some of the old fields were extended and deeper pay zones were discovered in others. These have given the areas greatly increased oil reserves and therefore are just as important as the discovery of new fields. The more important of the developments in 1940 are given, by states, in the following paragraphs. Colorado Hiawatha Field, Moffat County.—The Mountain Fuel Supply Co. began the development at Hiawatha of its oil reserves, which were discovered in about 1929, and late in the summer oil began moving from the field by truck to the shipping point at Rock Springs, Wyoming. The Hiawatha field of northwestern Moffat County was discovered in 1927 by the Sormir Petroleum Co., with the completion of No. r Florence Wilson for 4,5,000,000 cu. ft. of gas a day from a Wasatch sand lens at 2200 it. In later development of the field, oil showings were reported in several wells but no development of this resource was undertaken until 1940, when a test of the oil possibilities was started with the release in April of a location for No. 5-A Wilson on the S\W. SW. NW. of sec. 23-1zN-1ooW., on the east side of the field. The Well had an initial production of 327 bbl. of oil a day pumping from three Wasatch (Tertiary) sands between 2005 and 2540 ft. It was drilled to 2562 ft., where the 65/8-in. casing was cemented and gun-perforated at 2005 to 2125 ft., 2260 to 2335 ft. and 2513 to 2540 ft. At the end of the year, this well was averaging zoo bbl. of oil per day, pumping. Two other wells were drilled for oil on Hiawatha during the summer—one a small well of 60 bbl. per day and the other a small gas well. Powder Wash Field, Moffat County.—The development of the Powder Wash field in northwestern Colorado was resumed in 1940 by the Mountain Fuel Supply Co., with the release of a location for No. 2-A Musser in the CWL.NW.SE. of sec. 4-1rN-97W. The Powder Wash field was discovered in 1931 by the Mountain Fuel Supply Co. and the discovery well, No. I Musser, on C.NW. of sec. 5-IIN-97W., was completed at 2152 ft. in the Hiawatha member of the nonmarine Wasatch for-mation for an open flow of 34,000,000 cu. ft. of gas per day under a natural pressure of 685 lb. per sq. inch. Oil was discovered in the Powder Wash field on Nov. 26, 1936, in the company's No. I Carl Allen on the NE.SW.SE. of sec. 32-12N-97W. The oil production was

Jan 1, 1941

By C. E. Shoenfelt

There was a notable decrease in drilling operations in 1940 in all of the Rocky Mountain states except Montana, where the two large fields on the Canadian border, Cut Bank and Kevin-Sunburst, were espe-cially active. The expanding markets for Montana natural gas made necessary the more intensive development of such fields as Rowdoin, Cedar Creek and Devon. While there were no important oil and gas discoveries in 1940 in any of the Rocky Mountain states, a few small pools were opened, which may constitute separate areas but may prove with later development to be extensions of old fields. Some of the old fields were extended and deeper pay zones were discovered in others. These have given the areas greatly increased oil reserves and therefore are just as important as the discovery of new fields. The more important of the developments in 1940 are given, by states, in the following paragraphs. Colorado Hiawatha Field, Moffat County.—The Mountain Fuel Supply Co. began the development at Hiawatha of its oil reserves, which were discovered in about 1929, and late in the summer oil began moving from the field by truck to the shipping point at Rock Springs, Wyoming. The Hiawatha field of northwestern Moffat County was discovered in 1927 by the Sormir Petroleum Co., with the completion of No. r Florence Wilson for 4,5,000,000 cu. ft. of gas a day from a Wasatch sand lens at 2200 it. In later development of the field, oil showings were reported in several wells but no development of this resource was undertaken until 1940, when a test of the oil possibilities was started with the release in April of a location for No. 5-A Wilson on the S\W. SW. NW. of sec. 23-1zN-1ooW., on the east side of the field. The Well had an initial production of 327 bbl. of oil a day pumping from three Wasatch (Tertiary) sands between 2005 and 2540 ft. It was drilled to 2562 ft., where the 65/8-in. casing was cemented and gun-perforated at 2005 to 2125 ft., 2260 to 2335 ft. and 2513 to 2540 ft. At the end of the year, this well was averaging zoo bbl. of oil per day, pumping. Two other wells were drilled for oil on Hiawatha during the summer—one a small well of 60 bbl. per day and the other a small gas well. Powder Wash Field, Moffat County.—The development of the Powder Wash field in northwestern Colorado was resumed in 1940 by the Mountain Fuel Supply Co., with the release of a location for No. 2-A Musser in the CWL.NW.SE. of sec. 4-1rN-97W. The Powder Wash field was discovered in 1931 by the Mountain Fuel Supply Co. and the discovery well, No. I Musser, on C.NW. of sec. 5-IIN-97W., was completed at 2152 ft. in the Hiawatha member of the nonmarine Wasatch for-mation for an open flow of 34,000,000 cu. ft. of gas per day under a natural pressure of 685 lb. per sq. inch. Oil was discovered in the Powder Wash field on Nov. 26, 1936, in the company's No. I Carl Allen on the NE.SW.SE. of sec. 32-12N-97W. The oil production was

Jan 1, 1941

By R. J. Wasilewski

THERMAL expansion of rhenium data have been reported by Agte et al.,&apos; and Medoff and cadoff,&apos; respectively, while the linear expansion coefficient was determined by Sims et Al.3 Denoting expansion coefficients parallel and at right angle to c axis by all and Al respectively, their weighted mean should be equal to dilatometric linear coefficient of a random polycrystalline specimen. The values reported for these coefficients are tabulated below: Since these values are in poor agreement, and because of anomalous expansion behavior observed in titanium 4 and chromium, a rede termination of the axial expansion was carried out. A Unicam 19-cm-diam high-temperature camera was used, with unfiltered CuK radiation. Camera calibration was carried out using at Pt wire standarde at temperatures up to 1100oC, the variation between indicated and true temperature being within the experimental error (estimated at <3oC) above 750o C. Rhenium Johnson Matthey spectrographic standard) was vacuum annealed at 1000 oC prior to X-ray diffraction experiments. Lattice parameters were obtained by least-squares solution using the reflec- tions (1232), (1015), (2024), and (3030) for all the patterns, and the additional reflection (2133) for higher temperature (400°C and above) patterns. The relative expansion data obtained are shown in Fig. 1, lengths of the vertical bars indicating the spread in the parameter values obtained by using various combinations of three spacings from the four or five measured. The data calculated from the equation of Ref. 2 are included for comparison purposes. Several specimens were used to obtain the above data, neither of them showing a significant parameter change after completion of the high temperature runs. Some parameter data and the corresponding expansion coefficients between 25 oC and the measurement temperature are tabulated below. The comparison of the present data with those previously reported shows reasonable agreement with the results of Medoff and cadoff2 within the temperature range covered by them (up to 1000 oC). The a values are appreciably higher throughout most of the investigated temperature range. The basal expansion is—in agreement with their findings—appreciably higher than that in the direction of hexagonal axis. The expansion coefficient, al, however, decreases rather more slowly with temperature than previously reported. The expansion along the c axis up to nearly 1000°C appears in excellent agreement. However, at higher temperatures there is a marked deviation towards higher expansion, reproducible between different specimens. Furthermore, there seems to be some irregularity in the variation of all with temperature, the apparent local minimum and maximum values at 510o and 1024o C, Table II, being well outside the experimental error limits. It must be stressed that the apparent discontinuity in the c parameter expansion is still insufficient to account for the expansion value reported by Agte et al.&apos; since a total expansion of close to 2 pct would

Jan 1, 1962

By R. S. Dean

The commercial production of electrolytic manganese on a small scale commenced in 1939. The writer made a short report on the progress of production and utilization in Mining and Metallurgy for January 1941. Progress during the last two years, naturally, has been more rapid. In June 1940, Congressman (now Senator) Scrugham presented a proposal to Congress for an appropriation authorizing erection of a pilot plant for " the production of metallic manganese by electrolytic or other means." As a result of this, a pilot plant, having a capacity of a few hundred pounds per day was built at Boulder City, Nev. Subsequent appropriations permitted expansion of the plant to about a ton per day. Much has been learned in this plant about electrolytic manganese, and the product even in its small way has found war uses of considerable importance. Meanwhile, the Knoxville plant of the Electro Manganese Corporation, the sole commercial producer, was expanded to about 4 tons per day to supply needed material for the war program. Other proposals for commercial plants have not been favorably received by the War Production Board. The Bureau reported on one such proposal by the American Alloys and Chemical Corporation. Practice at BouldeR City The present practice, as carried out at Boulder City, which is being described in more detail in a current paper by the Bureau staff at Boulder City, starts with a manganese dioxide ore containing about 20 per cent manganese. Currently this ore comes from the Three Kids deposit near Las Vegas. The steps for the production of electrolytic manganese, in general, are as follows: 1. The manganese in the ore is reduced to MnO. 2. The MnO is dissolved from the ore in spent electrolyte, which contains about 38 to 47 grams per liter of free sulphuric acid, 135 grams per liter of ammonium sulphate, and 10 to 12 grams per liter of Mn as sulphate. In the leaching step the manganese is built back up to 32 to 36 grams per liter of Mn as sulphate; the pH is adjusted to neutral by means of gaseous ammonia and passed through thickeners. 3. The electrolyte is purified by adding H2S, which precipitates the heavy metals. After filtering, ferrous sulphate is added to the solution and oxidized with air and the solution is filtered and clarified on a precoat filter. 4. The purified catholyte is electrolyzed in a diaphragm cell using stainless-steel cathodes and lead-silver anodes. The current density is about 45 amp. per sq. ft. Current efficiencies of 60 to 65 per cent are regularly obtained.

Jan 1, 1944

By R. S. Dean

The commercial production of electrolytic manganese on a small scale commenced in 1939. The writer made a short report on the progress of production and utilization in Mining and Metallurgy for January 1941. Progress during the last two years, naturally, has been more rapid. In June 1940, Congressman (now Senator) Scrugham presented a proposal to Congress for an appropriation authorizing erection of a pilot plant for " the production of metallic manganese by electrolytic or other means." As a result of this, a pilot plant, having a capacity of a few hundred pounds per day was built at Boulder City, Nev. Subsequent appropriations permitted expansion of the plant to about a ton per day. Much has been learned in this plant about electrolytic manganese, and the product even in its small way has found war uses of considerable importance. Meanwhile, the Knoxville plant of the Electro Manganese Corporation, the sole commercial producer, was expanded to about 4 tons per day to supply needed material for the war program. Other proposals for commercial plants have not been favorably received by the War Production Board. The Bureau reported on one such proposal by the American Alloys and Chemical Corporation. Practice at BouldeR City The present practice, as carried out at Boulder City, which is being described in more detail in a current paper by the Bureau staff at Boulder City, starts with a manganese dioxide ore containing about 20 per cent manganese. Currently this ore comes from the Three Kids deposit near Las Vegas. The steps for the production of electrolytic manganese, in general, are as follows: 1. The manganese in the ore is reduced to MnO. 2. The MnO is dissolved from the ore in spent electrolyte, which contains about 38 to 47 grams per liter of free sulphuric acid, 135 grams per liter of ammonium sulphate, and 10 to 12 grams per liter of Mn as sulphate. In the leaching step the manganese is built back up to 32 to 36 grams per liter of Mn as sulphate; the pH is adjusted to neutral by means of gaseous ammonia and passed through thickeners. 3. The electrolyte is purified by adding H2S, which precipitates the heavy metals. After filtering, ferrous sulphate is added to the solution and oxidized with air and the solution is filtered and clarified on a precoat filter. 4. The purified catholyte is electrolyzed in a diaphragm cell using stainless-steel cathodes and lead-silver anodes. The current density is about 45 amp. per sq. ft. Current efficiencies of 60 to 65 per cent are regularly obtained.

Jan 1, 1944

By E. Richard Randolph, Rolland L. Blake, Stanley H. Ward, Gerald J. Anderson

During the last 30 years the inductive electro- magnetic method has been used chiefly in the search for massive sulphide mineralization. This application has met with varying degrees of success and in recent years has resulted in discovery of several large orebodies. Little has been written concerning its use in exploration for soft iron ores, but one of the present authors has reported on experiments with massive magnetic deposits. To augment the exploration tools available to geologists in delineating iron orebodies, Cleveland-Cliffs Iron Co. and McPhar Geophysics Ltd. undertook in 1953 to apply the inductive electromagnetic method to Cleveland-Cliffs properties in the Lake Superior region. As a result of this project, equipment has been developed that enables simultaneous transmission of two audio frequency waves, and the field technique and interpretative procedure involved have furthered exploration in the district significantly.

Nov 1, 1955

By William Price

DURING the past three or four years, the fabricators of silicon-bronze alloys have endeavored to induce risers of phosphor bronze to use instead the silicon-bronze alloys, claiming that the silicon bronzes are superior to the phosphor bronzes for switches and springs, or where high fatigue resistance is desired. This paper gives the results of tests comparing several phosphor bronzes with a 3 per cent silicon bronze and a copper-nickel-tin alloy (Adnic), all processed by the Scovill Manufacturing Co. So far as the authors are aware, sheet-metal fatigue tests have not been made on any of the alloys included in this report, except on one phosphor bronze, material C, Table 1, which was tested by Townsend and Greenall1.

Jan 1, 1937

By Oscar A. Glaeser

INDUSTRIAL relations in the United States Smelting Refining and Mining Company&apos;s Western operations covers the field of personnel and labor relations, and the principal aims are to render service to the employes of the Company and to its operating departments. Accident prevention Safety is a primary function. A safety engineer is employed at each operation. The wholehearted support of Company officials, staff, and the working force has been most successful in preventing accidents. Constant vigilance has been combined with a policy of building safety into all operating activities whether these are in the construction of a new facility, the developmnt of a mining system, or the direction of the working force. That this policy has produced results is attested to by the fact that the accident frequency rate at the Company&apos;s major mining operations in Utah has been reduced approximately 75 per cent in the ten-year period ending Dec. 31. 1946.

Jan 1, 1948

By E. T. Turkdogan, P. Grieveson

Molten silver is equilibrated with silicon nitride at 1400°C in nitrogen + hydrogen gas mixtures, and from the solubility data the activity coefficient of silicon is found to be 1.76 at silicon concentrations below 1 pct. Using this value, and that available from the silicon cmbide solubility measurements, together with those derived from the phase equilibrium diagvam, the activities of silver and silicon are estimated for the entire composition range. The main feature of the activity data is that there is a pronounced positive deviation from ideality. The activity of silver in molten silver containing up to 5 pct Si was determined by Schadel, Derge, and Birchenall1 by measuring the vapor pressure of pure silver and of the alloy over a temperature range of 850º to 1050°C. They deduced from their results that there is a positive deviation from Raoult&apos;s law and that the activity coefficient of silver increases with decreasing temperature. However, as pointed out by Kubaschewski and Catterall,2 their activity coefficients are much too high, giving silver activities greater than unity. At a later date McCabe and Birchenal13 showed that the previous vapor pressure data on silver4 were high by a factor of about 1.3; presumably a similar error must have occurred with the vapor pressure measurements on the Ag-Si alloys. The activities of silicon and silver calculated by tager&apos; from the phase diagram and by Gibbs-Duhem integration, respectively, show a positive deviation from Raoult&apos;s law for silicon activity and positive and negative deviations for the silver activity. According to these computations, at infinite dilution of silicon ygi = 1.12 at 1420°C. d&apos;Entremont and chipman6 measured the solubility of silicon carbide in molten silver at unit carbon activity; the equilibrium silicon content is found to be Nsi = 0.017 ± 0.002 atom fraction for 1420°C. Using the data of Grieveson and Alcock7 for the free energy of formation of silicon carbide from pure silicon and graphite, the activity of silicon for unit activity of carbon and of silicon carbide is asi = 0.0308 at 1420°c; therefore for the above solubility data on silver, YSi = 1.81, which is somewhat higher than that given by Hager. Use is often made of silver alloys in the measurements of activities of solutes in metals where silver has a very low solubility; in fact, Ag-Si and Ag-A1 alloys have been used in the past for such purposes. In an attempt to gain more thermodynamic data on molten Ag-Si alloys, measurements have been made in the present study on the solubility of silicon nitride in molten silver; the results on these solubilities are given in this paper together with a detailed discussion of activities of silver and silicon. SOLUBILITY OF SILICON NITRIDE The standard free energy of formation of silicon nitride is known with a reasonably high degree of accuracy. According to the measurements made by Hincke and Brantle8 and by Pehlke and Elliott,&apos; the following are the free energy data for the standard states of solid Si3N4, liquid silicon, and Nz at 1 atm pressure:

Jan 1, 1963

By Leland Wemple

PREVIOUS to 1915, zinc refining had not become a general practice among the zinc smelters in the United States. Such refining as had been carried on was confined chiefly to remelting very high-leaded zinc, such as third-draw metal from the retort furnaces, and slab dross, and hard spelter from galvanizing pots. In this remelting operation, the lead and iron were settled out and the refined spelter obtained graded fifth class, i.e., Prime Western. Owing to the presence of lead in most zinc ores, the bulk of the spelter produced by direct smelting is of this Prime Western grade. Careful selection of ores of low lead content gave purer grades of spelter, i.e., Brass Special and Intermediate; and smelters which could secure ores carrying practically no lead produced high-grade spelter. Thus, in general, the grade of spelter produced by any smelter was pre-determined by the purity of the ore it could obtain. The needs of the warring nations of Europe for enormous quantities of cartridge and other high-grade brass resulted in such a demand for the purer grades of spelter that the available supply of lead-free and low-lead ores could not produce the quantity required. Prime Western grades went begging, so to speak, while high grades sold at times from 5 to 15 c. per pound over the Prime Western market. The great demand, coupled with the wide market margin, which permitted the inherent costs and losses, resulted in the conversion of the lower grades into higher grades by processes of refining. These conditions also accentuated the development and size of the electrolytic plants, which were being worked out at the time this increased demand for pure grade of metal occurred. The electrolytic process, where available, produces a higher grade of spelter from impure ores than does the fire process; a large portion of those impurities in the ore, which by the distillation process would be carried into the spelter, are removed in the leaching of the ores and the purification of the solutions. The refining process, adopted at a number of smelters for the purpose of converting low-grade spelter into "grades suitable for brash was that of redistillation.

Jan 11, 1917

By Samuel S. Adams

Potash, the generic term for a variety of potassium-bearing minerals, ores, and refined products (Table I), owes its importance as an industrial mineral to the potassium requirement of growing plants. The term "potash" originally referred to potassium carbonate produced by the leaching of wood ashes. This process, for which the first U.S. patent was issued in 1790, was the basis for the largest United States chemical industry in the early nineteenth century. The agricultural use of potash soon eclipsed the chemical applications following the German discovery in 1840 that potassium is essential to plant growth. The initial discoveries of large deposits of soluble potassium minerals, essential for agriculture applications, were made in 1857 in Germany and in 1914 in the United States. More than 90% of the 20.4 million short tons K2O produced in the world in 1970 (Eilertsen, 1971 ) was derived from marine evaporite deposits and approximately 90% was used in fertilizers. The potassium content of an ore, mineral, or product is customarily expressed as % K,O, a unit of measure which is neither a natural nor synthetic compound of potassium (1 .O% K is equivalent to 1.2046% K,O) . Geology Potassium, the seventh most abundant element in the earth&apos;s crust, is present in silicate minerals in igneous, sedimentary and meta- morphic rocks. Potassium is also a major constituent of many surface and subsurface brines (Table 2). Economic potash deposits are essentially restricted, however, to widespread, thick accumulations of marine chloride evaporite deposits. These deposits yield high grade, large tonnage ore bodies, many of which are amenable to low cost mining and beneficiation. The products from these deposits are, moreover, ideal for use in fertilizer because of the high relative solubility of the potassium chloride and sulfate evaporite minerals. World potash production and reserves for such de- posits so vastly overshadow other sources of potassium that the following discussion will be limited largely to potash deposits in marine evaporites with brief reference to certain potash-rich brines. Approximately 85% of current domestic production is from bedded salt deposits and much of the balance is from brines. Marine evaporite deposits are accumulations of salt minerals deposited in structural sedimentary basins through the evaporation of sea-water or mixtures of seawater and other brines. The salt minerals are precipitated in assemblages and sequences of assemblages as determined by the compositions of the brines and the solubility relations in the salt systems (D&apos;Ans, 1933). The evaporation of seawater normally yields carbonate minerals as the first precipitates (Table 3). Further evaporation and concentration of the brine leads to the precipitation, in succession, of sulfate, chloride, and supersaline mineral assemblages including the salts of potassium and magnesium. The common minerals, ores, and products of potassium deposits are listed in [Table 1]. Many potash deposits contain accessory evaporite minerals together with a variety of detrital and authigenic silicates (Braitsch, 1971).

Jan 1, 1975

By Richard E. Chism

SAN DIMAS, in the State of Durango, Mexico, on the frontier of the State of Sinaloa, is the centre of an extensive and rich mining region, which has been exploited for over a hundred years; and the patio process for working silver ores has there attained the highest perfection of which it is capable. Local modifications have been engrafted upon the underlying principles of the process, but, as a whole, the San Dimas practice so fully illustrates its typical capabilities, that I have undertaken to describe its workings in the hope of lightening, to some degree, the labors of my professional brethren who may have occasion to visit Mexico." As is tolerably well known, the patio process, like all other systems of free amalgamation, is not successful with ores containing more than a trace of zinc or lead, the presence of zincblende being especially obnoxious. Iron and copper in small quantities are not particularly disadvantageous. The process succeeds very well with all sulphide ores which do not contain much more than a trace of arsenic and antimony, provided the tailings are concentrated, although, of course, it is best adapted for free milling ores. For suitable silver ores that contain small amounts of free gold the process is still a good one, but where the gold is combined with sulphurets, a considerable and even an excessive loss is inevitable. Hitherto the Mexicans have submitted to this loss, but, since the introduction of American mills, they are gradually abandoning the patio process in favor of the other. The San Dimas ores have a gangue of quartz and feldspar. They are composed principally of silver sulphides, with some chloride and

Jan 1, 1883

By Thomas L. Garwood, F. C. Menk

I T is generally accepted that no method of coal cleaning except froth flotation is effective in cleaning dust. In the majority of coals mined in the United States the dust sizes contain a high percentage of impurities, hence the removal of the dust from the coarse sizes lowers the impurity content of these sizes. Dedusted coal is desired as a means of providing a better feed to cleaning plants because of increased efficiency in both dry and wet plants. In dry-cleaning plants, a dedusted feed makes for a pervious and uni¬form bed. With a dusty feed the fines tend to segregate in the feed stream and pass en masse over the air separators, causing a lack of uniform aeration and fluidity of the bed necessary to efficient cleaning. In wet-cleaning plants deducting of the feed often decreases the sludge problem to the point of eliminating the necessity of wasting wash water. It may be advantageous to eliminate sludge-settling equipment in favor of dedusting equipment, to provide the advantages of a dedusted feed to the wet-washing process. Dedusting advantages may include: (1) the removal of fusain, especially advantageous in plants washing coal intended for metallurgical coke; (2) prevention of the gradual build-up of solids in the wash water, with a consequent variation in the washing ability of the system; (3) prevention of the loss of dust to the sludge ponds, providing instead a fuel for local consumption or special markets.

Jan 1, 1943

By P. R. Kalischer

In the production of alloys by powder metallurgical processes it is often necessary or desirable to include one or more cornponents that tend to form very stable oxides. Included in this group of metals are aluminum, manganese, magnesium, silicon, and a few others. In many cases it is not necessary for the sintered compact to have full density and the other physical characteristics of a cast alloy and in that event no undue precautions need be taken. If, however, it is required that the sintered part be entirely homogeneous, and have maximum density and physical properties, some method must be found to reduce the surface films of oxide, which are always present on the metals, and for the metals mentioned above this is always extremely difficult, if not impossible. since the production of high-density alloys is of particular interest to powder metallurgists, some experiments were undertaken to devise methods of reducing the refractory oxides. For this work, alloys of iron, nickel, and aluminum were chosen because aluminum oxide is one of the most stable oxides and because these alloys in the right compositions form excellent permanent magnets. All of the pertinent properties of the magnets could be accurately and delicately measured by density measuremerits and magnetic tests of sufficient scope to give a complete demagnetization curve. From such a curve the maximum coercive force, residual magnetism, and energy products could be obtained and compared with the same properties for a cast material. Any lack of homogeneity, density, or solid diffusion would be immediately apparent as a decrease in the magnetic properties. Nature and Removal of Surface Barriers The early work of the present investigation was based upon published processes.* In the published information it was claimed that by intimately mixing iron, nickel, and iron-aluminum alloy (50 Per cent Fe, So Per cent Al) powders, compressing such a mixture into the desired shape and size, and then sintering (heating to a temperature below the melting point of the component metals) in hydrogen at 1200°C. or higher, a sound, homogeneous article could be made having the desired physical size, shape, and strength, and good magnetic characteristics. However. this early work showed clearly that something in the powder compress was inhibiting diffusion and the process was almost entirely unworkable. In the initial phase of the investigation samples of iron powder, nickel powder, and iron-aluminum alloy powder were pressed into separate bars and sintered in hydrogen. Both the iron and nickel powders sintered

Jan 1, 1941

By P. R. Kalischer

In the production of alloys by powder metallurgical processes it is often necessary or desirable to include one or more cornponents that tend to form very stable oxides. Included in this group of metals are aluminum, manganese, magnesium, silicon, and a few others. In many cases it is not necessary for the sintered compact to have full density and the other physical characteristics of a cast alloy and in that event no undue precautions need be taken. If, however, it is required that the sintered part be entirely homogeneous, and have maximum density and physical properties, some method must be found to reduce the surface films of oxide, which are always present on the metals, and for the metals mentioned above this is always extremely difficult, if not impossible. since the production of high-density alloys is of particular interest to powder metallurgists, some experiments were undertaken to devise methods of reducing the refractory oxides. For this work, alloys of iron, nickel, and aluminum were chosen because aluminum oxide is one of the most stable oxides and because these alloys in the right compositions form excellent permanent magnets. All of the pertinent properties of the magnets could be accurately and delicately measured by density measuremerits and magnetic tests of sufficient scope to give a complete demagnetization curve. From such a curve the maximum coercive force, residual magnetism, and energy products could be obtained and compared with the same properties for a cast material. Any lack of homogeneity, density, or solid diffusion would be immediately apparent as a decrease in the magnetic properties. Nature and Removal of Surface Barriers The early work of the present investigation was based upon published processes.* In the published information it was claimed that by intimately mixing iron, nickel, and iron-aluminum alloy (50 Per cent Fe, So Per cent Al) powders, compressing such a mixture into the desired shape and size, and then sintering (heating to a temperature below the melting point of the component metals) in hydrogen at 1200°C. or higher, a sound, homogeneous article could be made having the desired physical size, shape, and strength, and good magnetic characteristics. However. this early work showed clearly that something in the powder compress was inhibiting diffusion and the process was almost entirely unworkable. In the initial phase of the investigation samples of iron powder, nickel powder, and iron-aluminum alloy powder were pressed into separate bars and sintered in hydrogen. Both the iron and nickel powders sintered

Jan 1, 1941

Aamot, Olav Crone, (M&apos;29) Chem. Engr., Elektro¬kemisk, Raadhusgt, 23; Oslo, Norway. Abadilla. Quirico A., (M&apos;33) Min. Engr., Dir., Bureau of Mines, Manila, P. I. Abbott, Agatin T., ( J&apos;40) Asst. Geol., Trench Mine, Patagonia, Ariz. Abbott, Clarence E., (M&apos;04) Civil Engr., V.P., Tennessee Coal Iron & R. R. Co.. 159&apos;3 Brown Marx Bldg.. Birmingham, Ala. Abel, Raymond L., (M&apos;28) Chem. Engr., Chief of Inspection Div., Pittsburgh Chem. Warfare Pro¬curement Dist., American Batik Bldg., Pitts¬burgh. Pa. Abel, Walter D., (M&apos;32) Min. Engr.. Div. of Cor¬porations, State of Calif.. 403 California State Bldg., Los Angeles, Calif. Abele. Louis T., (M&apos;31) 4800 Patterson Ave.. Richmond, Va. Abell, Leo M., (M&apos;311 Research Met., Mount Mor¬gan Ltd., Mount Morgan, Queensland, Australia. Abenius, Hakan V., (M&apos;37) c/o Falu Gruva, Falun, Sweden. Abernathy. G. E., (M &apos;33S) Geol., Kansas State Geol. Survey. Pittsburg, Kan. Abernathy, Jack. H.. (M&apos;40) Chief Engr., Sunray Oil Co.. Philtower B1dg., Tulsa. Okla. Ahorn, Robert H., (M&apos;19) Asst. Met., Research Lab., U. S. Steel Corp., Lincoln Highway, Kearny, N. J. Abraham, A. W., (M&apos;30) Petr. Engr., Richfield Oil Corp., 555 S. Flower St., Los Angeles. Calif. Abramowitz, William L., (J&apos;40) Chem., National Oil Products Co., Harrison, N. J. Abrams, Charles Jackson, (M&apos;36) Gen&apos;l Supt., Climax Molybdenum Co.; Climax, Colo. Abstein, Henry T., (M&apos;27) Yellow Pine, Idaho. Ackerman, D. E., (M&apos;35) McKinsey & Co., 2 Wall St., New York, N. Y. Ackerman. E. Dumont, (A&apos;3S) Petr. Geol.. Dist. Geol., Quiriquire&apos; Dist., Standard Oil Co. of Venezuela, Caripito, Venezuela.

Jan 1, 1941