Search Documents

By John R. Spencer

A capillary tube variable volume cell is described, which has operated satisfactorily over a range of 100°F and 3,500 psi to 550°F and 1,500 psi. The cell contents are entirely visible over the length of the capillary with the exception of a space at the top amounting to three per cent of the total volume. Observations on the critical behavior of simple systems have been greatly facilitated by the apparatus, it being possible to establish the critical conditions for a particular mixture in the course of a day's run. INTRODUCTION Many types of apparatus have been designed for obtaining data on the phase relationships of hydrocarbon systems. Such apparatus can in general be subdivided into two classifications; (l), indirect measurement of phase volume, and (2), direct visual observation of phase volume, each of which has outstanding advantages and disadvantages. Indirect measurement of phase volume requires the use of rather elaborate apparatus including internal probes in which are located the device for determining the locus of the interface between phases. Such equipment is by its very nature costly, and is complex from the standpoint of operating technique. Probing techniques can be used, however, over wide ranges of temperature and pressure with a high degree of reproducibility. Apparatus for visual observation of phase behavior obviously has the advantage of enabling the experimenter to see exactly what takes place, but because the material to be tested is contained in a cell constructed of both metal and glass, is limited severely as to the temperature range of operation. Furthermore. the maximum pressure usually is limited by the choice of material used for sealing the glass to the metal, and by the strength of the glass itself. In the interest of increased efficiency of observation, as much of the cell as possible should be visible to the eye. Glass capillary tubes have been used successfully but have always given difficulty at the metal-to-glass seal. An apparatus has been devised to overcome the problems of sealing and resistance to temperature effects that have heretofore been the limiting factor with glass apparatus in the observation of phase volumes at elevated temperature and pressure. APPARATUS The objective which dictated the general arrangement of the apparatus (Figs. 1 and 2) was simplicity of operation. The air bath, A, was constructed of an iron framework to which was attached approximately one inch of glass wool bats which were covered on the outside with "Masonite." A roughly octagonal center piece was installed to provide forced circulation of the air by the fan, B, past the heaters, D, cell, F, and thermoregulator, C, respectively. The entire top of the box is removable to facilitate charging of the cell and to permit easy maintenance. Two windows are provided before and behind the cell to allow the operator to observe the contents against the background fluorescent light, E. The heaters,

Jan 1, 1951

By John R. Spencer

A capillary tube variable volume cell is described, which has operated satisfactorily over a range of 100°F and 3,500 psi to 550°F and 1,500 psi. The cell contents are entirely visible over the length of the capillary with the exception of a space at the top amounting to three per cent of the total volume. Observations on the critical behavior of simple systems have been greatly facilitated by the apparatus, it being possible to establish the critical conditions for a particular mixture in the course of a day's run. INTRODUCTION Many types of apparatus have been designed for obtaining data on the phase relationships of hydrocarbon systems. Such apparatus can in general be subdivided into two classifications; (l), indirect measurement of phase volume, and (2), direct visual observation of phase volume, each of which has outstanding advantages and disadvantages. Indirect measurement of phase volume requires the use of rather elaborate apparatus including internal probes in which are located the device for determining the locus of the interface between phases. Such equipment is by its very nature costly, and is complex from the standpoint of operating technique. Probing techniques can be used, however, over wide ranges of temperature and pressure with a high degree of reproducibility. Apparatus for visual observation of phase behavior obviously has the advantage of enabling the experimenter to see exactly what takes place, but because the material to be tested is contained in a cell constructed of both metal and glass, is limited severely as to the temperature range of operation. Furthermore. the maximum pressure usually is limited by the choice of material used for sealing the glass to the metal, and by the strength of the glass itself. In the interest of increased efficiency of observation, as much of the cell as possible should be visible to the eye. Glass capillary tubes have been used successfully but have always given difficulty at the metal-to-glass seal. An apparatus has been devised to overcome the problems of sealing and resistance to temperature effects that have heretofore been the limiting factor with glass apparatus in the observation of phase volumes at elevated temperature and pressure. APPARATUS The objective which dictated the general arrangement of the apparatus (Figs. 1 and 2) was simplicity of operation. The air bath, A, was constructed of an iron framework to which was attached approximately one inch of glass wool bats which were covered on the outside with "Masonite." A roughly octagonal center piece was installed to provide forced circulation of the air by the fan, B, past the heaters, D, cell, F, and thermoregulator, C, respectively. The entire top of the box is removable to facilitate charging of the cell and to permit easy maintenance. Two windows are provided before and behind the cell to allow the operator to observe the contents against the background fluorescent light, E. The heaters,

Jan 1, 1951

By F. L. Bosqui

NO metallurgical process developed in the last half century has been more widely advertised to both technologists and lay- men, or has done more to promote efficiency and economy in the extraction of the valuable portions of ores than has the flotation process. Practically everybody has heard of this strange procedure whereby the heavy portions of an ore are made to float while the light parts sink. Some- times it is called froth flotation, the mineral-bearing froth being from the first a distinguishing characteristic. Many times it is called oil flotation, because a thin film of oil was commonly applied to the particles to be floated to make them adhere to the bubbles that rise through the pulp to form the surface froth. Oil, though commonly used, is not, however, necessary for this purpose, which is one of the facts that has been learned as the process has been developed.

Jan 1, 1940

By A. W. Asman

The problem of balanced design in a belt conveyor has been under constant study. Increased use of this method of transport in recent years has stimulated investigations. Conveyor belt, power transmission and other machinery should be adequate to perform the required service. All components of the belt conveyor should work as an efficient unit moving its load continuously between terminals. As part of a long term research project on belt conveyors, Hewitt-Robins established in 1954 a 2-year grant at Pennsylvania State University. Under terms of the grant, certain fundamental phenomena were to be studied. This work evolved a new concept in belt conveyor power determination based on the principle of belt tension. The Penn State contract furnished the foundation for later more detailed studies. From these most recent investigations, more specific factors were defined. In the final analysis, all of the data collected has been worthwhile in belt conveyor design. Units now operate over long distances at speeds of over 800 fpm. Long high lifts are commonplace. Where vertical or inclined shafts were the rule, belt conveyors receive first consideration. Although belt conveyors have moved forward rapidly, the future will see a tremendous gain in their use. The ideal test belt conveyor would be several thousand feet in length and have a maximum tension of at least 70,000 lb., Also, this conveyor should be horizontai and have a variable feed rate of more than one material. Data from such a field belt conveyor combined with laboratory information would permit accurate analysis. Since this type of conveyor was not available, many field locations were visited: An alternate would have been to erect a closed circuit system in the laboratory. Either method had limitations and the first was selected as having the best possibilities. Manufacturers of conveyor belting and machinery basically have been using the same horsepower formula. As more information became available from field installations, factors in the basic formula were modified. Practically all conveyors are designed today by adding together the horsepowers required to move the empty belt, move the load horizontally, and elevate the load. In selecting size of drive motor, the first two elements are relatively unimportant if the last is large. However, it is the combination of

Jan 1, 1961

By R. F. Krueger

Results are presented from tests of dynamic fluid-loss rates to cores from clay-gel water-base drilling fluids containing different commercial fluid-loss control agents (CMC, polyacrylate or smt,ch), organic viscosity reducers (quebracho and complex metal lignosulfonate) and oil at several different levels of concentration. In the dynamic system the most effective individual additives to the clay-gel drilling fluid, based on cost-equalized concentrutiom, were found to be starch and the viscosity reducers. These results do not conform with the rankings determined by API fluid-loss rests, which indicate CMC, polyacrylate and starch to be the most effective and comparable. Generally, minimum dynamic fluid-losr rates were attained at cost-equalized concentrations of additive (including thinner) of about $1.00/ bbl, or less. For chernically treated clay-gel drilling fluids, both the standard and the high-pressure API filter-loss tests were found to he inaccurate indicators of trends in dynamic fluid-loss rates under the test conditions used, particulurly for drilling muds containing viscosity reducers. From a practical field viewpoint, restrictions on the applicability of the API fluid-loss test are such that it is open to question whether or not results of this test can be used routinely with confidence as an indicator of control of down-hole fluid loss under field treating conditions. INTRODUCTION The petroleum industry spends large sums of money during drilling operations to control the fluid-loss properties of drilling fluids based on the standard API filter-loss test,' which is a static filtration system. Laboratory studies' ' of dynamic filtration have shown that in a given time period filtrate loss from a circulating mud stream is greater than from a static system and that it is a function of linear mud velocity, pressure and the properties of the drilling fluid. Ferguson and Klotz' and Horner, et al," observed that (I) the dynamic fluid-loss rates for the drilling fluids used were not related to the extrapolated API filter loss and (2) the drilling fluids with the lowest API filter losses did not have the lowest dynamic fluid-loss rates. However, there has been no published information on the relative effects on dynamic fluid-loss rate as a given drilling fluid is treated with increasing amounts of chemical additive to reduce the API filter loss. Such information is economically important because drilling-fluid costs rise rapidly as chemical requirements increase. This paper presents the results of a study of dynamic filtratioi rates to cores from a clay-gel water-base drilling fluid treated with various commercial viscosity reducers and chemical fluid-loss control agents. The dynamic fluid-. loss rates to cores are compared with the standard API filter-loss values at several different levels of additive concentration. Dynamic filtration rates were obtained in each experiment under two different simulated wellbore conditions: (1) filtration just above the bit through a new mud cake laid down dynamically on a freshly drilled formation and (2) filtration up-hole through a mud cake formed by deposition of a static filter cake on top of the initial dynamically formed cake. The latter case corresponds to the bottom-hole conditions existing above the bit when mud circulation is restarted after a stand of pipe has been added or a round trip has been made to change the bit. Except for the short-duration, high-rate filtration beneath the bit where no mud cake can form, these two conditions probably represent the two extremes of dynamic filtration. Because thickness of a dynamic mud cake formed on freshly exposed formation is limited by the shearing action of the mud stream, the filtration rate for this condition is high. On the other hand, once circulation is stopped and a static mud cake forms on top of the dynamic cake, re-starting circulation has only a small effect on the cake properties and filtration rate is much lower thereafter. A discussion of the mechanics of mud-cake deposition and dynamic filtration is outside the scope of this paper but may be found in more detail in publications by prior investigators. APPARATUS AND EXPERIMENTAL CONDITIONS The test equipment used to simulate the dynamic flow conditions existing during drilling was a modification of that described previously by Krueger and Vogel: A schematic flow diagram is shown in Fig. 1. In general, a power-driven, high-pressure mud pump capable of delivering up to 60 gallmin was used to circulate drilling fluid parallel to the faces of 1-in. diameter sandstone cores mounted in a 2 3/4-in. ID high-pressure test cell. Pump rates were controlled by means of a magnetic clutch to maintain an average axial fluid velocity of 110 ft/min in the annular space between the cell wall and a 1 1/2-in. rod positioned on the center line of the cell. The core specimens were Berea sandstone plugs sealed with plastic inside 1 1/8-in. OD tubes and were fluid-saturated prior to use. Burettes were used to accumulate fluid discharged from the cores. The mud sump shown was used for treatment and storage of the drilling-fluid samples during a particular test. The valve arrangement permitted either (1) circulating drilling fluid through the by-pass line while treating with

"NAME…""Utah"" is derived from the name of the Indian tribe, variously spelled ""Yuta, “Ute"" ""Youta,"" ""Uta,"" ""Eutaw,"" and finally ""Utah."" It means ""in the tops of the mountains,"" or ""on the heights."" The state emblem is the ""Beehive,"" typical of industry. State nickname is ""Beehive State.""AREA…Utah is the tenth state in area. It contains 84,990 square miles, of which 2,806 miles are water. When admitted as a territory in 1850, Utah included all the area from the east line of California to the summit of the Rocky Mountains between the 37th and 42nd parallels, which embraced practically all of the present state of Nevada, all of western Colorado, part of Idaho and part of Wyoming, in addition to the present area of Utah.TOPOGRAPHY…Utah is generally mountainous, with several main ranges and also detached groups of mountains. The valleys are broad and level. The mean altitude of the state is 6,100 feet above sea level, which makes the state the third highest of the Union. The highest point in Utah is King's Peak (13,498) in the Uinta range. The lowest point is Beaverdam Creek (2,000) in Washington county.CLIMATE…The climate is diversified between mild temperate in the northern portion to semitropical in the southern portion. There are four distinct seasons. Snowfall is heavy at the greater altitudes and rare in the southern portion. Rainfall is moderate throughout the state. Extremes of heat and cold are unusual."

Jan 1, 1925

By W. A. Selvig

BY plotting fixed carbon against British thermal units of coals free from mineral matter, and ranging in rank from anthracite to lignite, it is found that the coals of higher rank, from anthracite to the higher rank of the high-volatile bituminous coals, inclusive, can be separated into groups according to their degree of metamorphism by reference to their fixed carbon. Such charts show also that the coals lower in rank can be best separated into groups with respect to B.t.u., especially when plotted on the moist basis, that is, coal containing its natural bed moisture. A tentative scheme for coal classification was presented at the October, 1932, meeting of the Technical Committee on Scientific Classification, of the American Standards Association Sectional Com-mittee on Coal Classification. This scheme was sponsored by Sub-committee IV on Tentative Classification of Coals, under the chairmanship of W. T. Thom, Jr. It proposed the grouping of coals according to rank by reference to fixed carbon and B.t.u., on the basis of coal containing its natural bed moisture but free from mineral matter. This scheme proposed classifying coals into four broad classes: (1) anthracitic, (2) bituminous, (3) subbituminous, (4) lignitic.. The anthracitic class was divided into three groups designated as meta-anthracite, normal anthracite, and semianthracite. The bituminous class also was divided into three groups, low volatile, medium volatile, and high volatile. The high-volatile group was further subdivided into four subgroups according to moisture content, as follows: (1) less than 5 per cent, (2) 5 to 10 per cent, (3) 10 to 15 per cent, and (4) 15 per cent and more. The subbituminous class was divided into two groups, group, 1 including subbituminous coals having calorific values of 10,500 B.t.u. or more, and group 2 including those with less than 10,500 B.t.u. , The lignitic class of coal was divided into two groups both below 8,000.B.t.u., the one group consisting of consolidated and the other of unconsolidated

Jan 1, 1934

By C. M. Sellars, F. Maak

Electvomotie -force measurements hazle been made on ten Au-Ni alloys at temperatures 7754 825O, 900O, and 935°C using galvanic cells with solid electrolyte. Partial and ivtegral thermodynamic functions are derived from the determined activities. which show la9,ge positive deviations jvom Raoult's law. The enthalpies of mixing- are in close accord with calorinletric data and are of comparable accuracy. The results are used to determine the miscibility gap and the spinoidal curL1e, and are qlalitaticely interpreted in terms of the large size difference and electvonic interactions between gold and nickel. Tabulated nalues of the actielities and partial and inteqal free energies, entropies , and enthalpies of mixing are given in the appendix. The Au-Ni binary alloys are of particular interest thermodynamically as despite the large size difference between gold and nickel atoms they have a simple phase diagram.' This shows complete solid solubility above a miscibility gap with a maximum at about 71 at. pct Ni and 810°C. Activity measurements (over a range of temperature) have been made previously on this system using an electrolytic-cell method with a liquid chloride eletrolyte. The accuracy of this data has, however, been queried3'4 as it leads to values for the enthalpy of mixing which are too high when compared with calorimetric measurements.46 Also, the entropy of mixing is too high when compared with the values derived from specific-heat measrements. It was therefore considered worthwhile redetermining the activity data using a galvanic cell with a solid electrolyte (0.85 ZrO, 0.15 CaO). This method is based on a technique introduced by Kiukkola and aner'' and has been used to determine the thermodynamic data for Cu-Ni alloys.' THE ELECTROLYTIC CELL The cell used to determine the activity of nickel in Au-Ni alloys was: The cell reaction, which is discussed for a similar cell by Rapp and Maak, gives a direct measurement of the activity of nickel in the alloys as where aNi(alloy) is the activity of nickel in the alloy, 3 is Faraday's constant, E is the measured electromotive force, R is the gas constant, and T is absolute temperature. For the valid application of this type of cell the arrangement must be ther modynamic ally stable, which means that: 1) The free energies of formation of the oxides fulfill the relation 2) The vapor pressures or dissociation pressures of each component must be so small that during the time of the experiment the amount of any material transported by the gas is negligible. 3) Side reactions which change the alloy composition must be negligible. These reactions are possible both with the surrounding gas atmosphere and with neighboring solid material. The first two conditions are fulfilled by the above cell.' The third condition is approached by care in the experimental technique. The factors which control the attainment of equilibrium in this type of cell have been considered by Rapp and aak, who conclude that metallic diffusion in the alloy is the rate-control ling step. A lower temperature limit for the practical application of this cell is therefore set by the condition that equilibrium must be attained in reasonable times. EXPERIMENTAL MATERIALS AND TECHNIQUE The starting materials were mint gold (99.99 pct Au) and Mond nickel (99.9 pct Ni). Alloys, nominally 5 at. pct Ni and then each 10 at. pct across the system, were produced by vacuum-levitation melting compacts of mixed drillings of the pure metals. The nickel used for the reference tablets in the cells was melted in a similar manner. The alloy ingots, cast in boron nitride molds, were cold-forged and

Jan 1, 1967

By S. Epstein

THE new low-alloy high-strength steels are obviously here to stay. With 75 per cent higher yield strength and 50 per cent higher tensile strength than plain carbon structural steel, they permit 20 to 40 per cent weight savings and 10 per cent or more increase in pay load in the con-struction of railroad cars, buses, trucks, and a great variety of material-handling equipment. Their cost is low enough so that the extra cost of the new lighter construction over that with carbon steel offers an attrac-tive self-liquidating investment; in some instances new construction with these low-alloy steels may even be as cheap as with plain carbon steel. A considerable and rapidly growing demand for the low-alloy steels has already sprung up. The many steel compositions that have appeared on the market lately 18,27,28,29,30 to meet this demand would seem to indicate that no single composition is uniquely fitted for the purpose. However, no doubt some compositions are more suitable than others. The purpose of this study was, therefore, to compare the effects of the various alloying elements that might be used in the low-alloy steels in order to choose the metallurgically most logical composition, paying due regard, of course, to the economic aspects involved.

Jan 1, 1936

By Ulick Evans

I SHOULD like to commence by saying how much I appreciate the honor which the American Institute of Mining and Metallurgical Engineers has done me in inviting me to visit your country, and to deliver this lecture before you. In choosing a subject, and in deciding what to include and what to omit, I have endeavored to discuss as far as possible work carried out recently in Europe with which you may not be unduly familiar. It would be poor return for your hospitality, and a mistaken sort of compliment indeed, if I were to load the lecture with accounts of researches carried out in your own country-researches with which you are probably better acquainted than I. Not that I have in any way excluded work done on this side of the Atlantic from my survey; one would indeed find it difficult to write on this, or on any other branch of science, without mentioning American work. But I have endeavored as far as possible to concentrate on aspects of the case which will, I hope, be comparatively fresh to you, and I feel fairly certain that this will be in accordance with your own wishes. If a strip of iron is heated strongly at one end, the other end remaining cold, there is produced over the heated portion a layer of oxide scale, the thickness of which diminishes steadily with the distance from the hot end. Somewhere in the middle of the strip, the thickness of the oxidized layer will become comparable to the wave length of light, and over this region the thin films give rise to a series of beautiful interference tints, commonly known as "temper colors." The colors are caused by the fact that two trains of light waves are reflected respectively from the outer and inner surfaces of the oxide film, and the possibility arises that the "crests" of one series of waves may coincide with the "troughs" of the other, thus diminishing the intensity of the light of some particular wave length. The state of affairs in this part of the strip is shown diagrammatically in Fig. 1, in which the film thickness is enormously exaggerated, of course, in comparison with the length of the strip; the

Jan 1, 1929

By Strathmore R. B. Cooke

That calcium will activate quartz for flotation with anionic collectors such as soaps has been known for a number of years,1 2 3 and the method has been applied to the concentration of various iron ore 4 5 6 as well as to other materials. Clemmer gives the permissible pH range for the activation of quartz by calcium as between 9.5 and 12.5 with an optimum value of 11.0, and Hertzog7 has determined the calcium abstraction of iron ores and of Ottawa sand, but otherwise little quantitative data are available. The purpose of the present investigation was to determine those conditions under which dilute solutions of calcium chloride will activate quartz for anionic flotation and to determine the amount of calcium ion adsorbed by quartz. Those variables, the influence of which was primary, such as calcium, sodium, and hydrogen ion concentrations, were studied. Other factors which influenced the results are discussed in the description of the experiments. Three different experimental methods were used to determine the activation of the quartz. The first method was to treat a sample of ground, deslimed quartz with solutions of calcium chloride and sodium hydroxide, and to determine the calcium adsorbed by chemical analysis of the solution. Ad- vantages are that a direct value for the

Jan 1, 1949

By Richard D. Snouffer

Prime topics of conversation these days are the new concepts of rail haulage for bulk items such as iron ore, potash and coal. We have heard such ideas as the "integral train" and the "unit train" discussed frequently during the past two years at various AIME meetings, and progress reports have kept up a steady appearance in the technical press and in local newspapers. While no railroad has a complete "unit train" in service at this moment, one has 50 fast-discharge cars under construction and the Pennsylvania Railroad has experimented with radio-controlled motive power distributed at intervals throughout the train. To a great extent, however, the promise for greater efficiency and lower costs held out to industry by these new haulage methods is dependent not on greater speed or larger cars or more dedicated equipment alone but, rather, on the utilization of modern practices in the loading and unloading of rail cars. It is the purpose here to examine these two key steps and the up-to-date procedures and equipment they entail.

Jan 7, 1963

By W. A. Eardley

FIFTEEN years ago the world's deepest oil well penetrated the earth about 7300 ft. That depth has now been more than doubled. Why has such deep drilling become necessary and how has it become possible? Three factors have had an important bearing: (1) Depletion of shallow zones, making it necessary to search for deeper producing measures. (2) The perfection of prospecting methods, which have been success- fully used to locate favorable buried structures, many at great depth. (3) Improvement in the quality of steels used for drilling.

Jan 1, 1940

By J. J. Jakosky

THE method of electrical mapping of oil structures to be described possesses certain limitations, as well as certain definite advantages. It, in common with other geophysical methods, is not a panacea for the solution of all subsurface geological problems. It operates on differences in electrical conductivity of the geological strata, whereas the other most-used methods operate on (1) differences in magnetic properties, (2) differences in gravimetric properties, or (3) differences in seismic properties. This modification of the resistivity method is therefore able to obtain subsurface information under conditions not favorable to the other methods mentioned. Where the other methods have been employed with ambiguous results it may act as a complementary method.

Jan 1, 1936

By H. N. Eavenson

Prior to 1907 nearly all coke was made in beehive ovens, and most of the gas produced was made in the old-style gas retorts, and while there were a few coke plants in southern West Virginia, southwest Virginia and Kentucky operating on high-volatile coals the proportion of the total product made by them was small and usually was used locally. The greater part of the coke made, and the coal gas produced, came from the Pittsburgh seam of western Pennsylvania and northern West Virginia, which was then regarded as the standard coking and gas coal of the country, and the best coal available anywhere for these purposes. With the advent of the byproduct oven and the building of coke plants at the furnaces, the restriction of the use of one grade of coal for making coke was removed and the use of mixtures of low-volatile and high-volatile coals began. The change in the locations of the coke plants removed the necessity of using Connellsville coal and also made sources of gas available to the public utilities other than of their own manufacture. Most of the first oven plants were built at points distant from the Connellsville region and this afforded an opportunity for the use of coals from the southern Appalachian fields, which were then at approximately equal distances from the ovens. Since that time development has been made on a number of seams of coal of great purity in southern West Virginia, southwestern Virginia and eastern Kentucky, which have been largely used for gas, cokemaking and metallurgical purposes where low amounts of ash, sulfur and phosphorus are determining factors. These coals are much lower in the objectionable elements than most of the coal shipped from the Pittsburgh seam, or than any northern coal, and when blended with low-volntile cod produce coke in byproduct ovens that is not excelled for any purpose by any coal mined in this country, and is equaled very seldom. Coal from several of these scams is shipped in great quantities without beneficlation and is lower in ash and sulfur than any but the best washed product from the Pittsburgh seam in the north. The writer has made a study of these coals to ascertain their relative qualities and the areas and reserves of coal available in each of them. No attention has been paid to the coals of Alabama, which do not compete with any of these coals, and no coal of equivalent quality is found in

Jan 1, 1934

By H. Wilhelm, E. L. Davis, W. A. Clark

MATHEMATICAL formulas for the analysis of the behavior of producing oil wells can be devised which will be correct for the assumed conditions. However, in an oil zone, variables always exist which are unknown, or to which. it is impractical to assign mathematical values. It seems apparent that one should reason back from observed facts to an analysis of causes, rather than start with a hypothetical reservoir with assumed properties and attempt to explain observed phenomena. In this paper we hope to throw some additional light on factors influencing production, especially edgewater behavior. OIL and gas are contained in reservoirs of either the sealed type or the edgewater type. In the former all the recoverable oil is produced by gas expansion only. In this type of reservoir, edgewater is not effective. This may be because of faulting or overlapping strata, or more often, probably, the edgewater pressure is ineffec¬tive on account of resistance or lack of head.

Jan 1, 1933

By N. G. W. Cook

At present, tunnels can be driven in rock by either of two essentially different techniques, in one of which rock-breaking is accomplished by drilling and blasting and in the other by mechanical loading. The methods based on these techniques are comparable in terms of the rates at which tunnels may be advanced, although they differ widely in their range of applicability to different types of rock and lengths of tunnel. The method based on drilling and blasting has reached a high degree of development. It is applicable to even the hardest rocks and rates of advance in excess of 50 ft per day (fpd) are attainable. The main disadvantages of this method are that it involves a sequence of operations punctuated by blasting and that it is relatively uncontrolled, resulting in overbreaking the tunnel profile and damage to the surrounding rock. However, its flexibility, mobility, and low capital cost constitute real advantages in many situations, such as those involving short lengths of tunnel or low rates of advance. Tunneling machines based on mechanical breaking of the rock are a more recent development. They offer a continuous and controlled means of tunneling capable of rates of advance in excess of 100 fpd under favorable conditions. However, these machines weigh many tens of tons and consume several hundred horsepower, so that they are costly and lack mobility. At present, their applicability is limited to long tunnels in relatively soft rock where the high rates of advance and tunnel quality can offset their onerous capital cost. Many situations exist in which the superior quality of a machined tunnel and freedom from blasting would be real advantages, but where the rock is either too hard for existing machines or the length of the tunnel does not justify their capital cost: What are the possibilities of developing cheaper, more flexible, and mobile tunneling machines? Most existing tunneling machines fragment all the rock at the tunnel face to facilitate its disposal. If a machine were used to cut only the profile of a tunnel as one of a sequence of operations, it would be required to break

Jan 1, 1970

By Herman Dykstra, R. L. Parsons

A numerical method for solving partial differential equations in steady state fluid flow is described. This method, known as the "relaxation method," has two advantages over analytical methods: (1) practically any problem can be solved, and (2) a solution can be obtained quickly. A disadvautage is that the solution is not general. The method is applied to core analysis and relative permeability measurement to calculate constriction effects and to calculate the true pressure drop measured by a center tap in a Hassler type relative permeability apparatus. Further applications are suggested. INTRODUCTION Many problems in fluid flow cannot be solved analytically because of the nature of the boundary conditions. For many problems, however. an exact answer is not necessary because boundary conditions are not exactly defined or the parameters describing the porous medium are not accurately known. The relaxation method can be used to obtain an approximate answer easily and quickly for the flow of incompressible fluids in porous media. The method can also be used for other types of problems, such as determining the stress in a shaft under load. or the temperature distribution during steady state heat flow. In this discussion only calculations concerned with the flow of fluids in porous media will be considered. The method was introduced by R. V. Southwell in 1935.' THEORY The treatment given here follows that given by Enimons.2 Consider a porous medium to be replaced entirely by a net of tubes of equal length and uniform cross-sectional area as shown in part in Fig. 1. Assume that the net of tubes behaves exactly like the porous medium which it replaces; that is, the net can be made fine enough to reproduce exactly the porous medium. Assume also that Darcy's Law can be used to calculate the flow from one point to another point through these tubes. The flow from point 1 to point 0 is KA . ------ P-P) .......(11 where a is the distance between points: K is the "permeability" of a tube; A is the cross-sectional area of a tube; is the viscosity of the liquid in the porous medium; and (P1 — P0) is the pressure difference between point 1 and point 0. In like manner the flow can be calculated from points 2, 3, and 4 to point 0. The net flow into point 0 is Qo = KA/µa (P1 + P2 + P33 + P4-4P0) . . (2) MB For an incompressible fluid the net flow into point 0 will be zero or, Q. = 0. This says that at point 0 fluid is neither being accumulated nor depleted. 'Therefore. P1 + P2 + P3 + P4 - 4P0 = 0 .... (3) . If. now. with specified boundary conditions. the pressure i.; known at a finite number of points in a given region, as at the points shown in Fig. 1, Equation (3) will be satisfied at every point. If, on the other hand, the pressure is not known, the pressure can be guessed at these points. Then. unless the guess is perfect. Equation (3) will not be satisfied at all of the points. When Equatiol~ (3,) is not satisfietl. let d = P1 + I?, + P, + P, - If' .,....(4) where 6 is an apparent error and is called the residual at point 0. Equation (4) shows how much the pressure guess is in error at point 0 with respect to the surrounding points. A positive residual means that the pressure is too low, and a negative residual means that the pressure is too high. To bring the residual, 6. to zero in order to satisfy Equation (3). it is necessary to make changes in the pressure guesses. Equation (4) shows that a +1 change in Po will change the residual at point 0 by -4. A +1 change in the pressure at any of the four surrounding points will change the residual at point 0 by +l. Thus it can be seen that a change at any point will affect the residual at that point and the four surrounding points. By changing the pressure from point to point, all of the residuals can eventually be brought nearly to zero and the problem will be solved. This procedure is the essence of relaxation methods and is used to relax the residuals so that Equation (3) is satisfied at every point. The procedure can be most easily explained in detail by solving a simple problem. as Southwell says, "To explain every detail of a practical technique is to risk an appearance of complexity and difficulty which may repel the reader. A

Jan 1, 1951

By R. L. Parsons, Herman Dykstra

A numerical method for solving partial differential equations in steady state fluid flow is described. This method, known as the "relaxation method," has two advantages over analytical methods: (1) practically any problem can be solved, and (2) a solution can be obtained quickly. A disadvautage is that the solution is not general. The method is applied to core analysis and relative permeability measurement to calculate constriction effects and to calculate the true pressure drop measured by a center tap in a Hassler type relative permeability apparatus. Further applications are suggested. INTRODUCTION Many problems in fluid flow cannot be solved analytically because of the nature of the boundary conditions. For many problems, however. an exact answer is not necessary because boundary conditions are not exactly defined or the parameters describing the porous medium are not accurately known. The relaxation method can be used to obtain an approximate answer easily and quickly for the flow of incompressible fluids in porous media. The method can also be used for other types of problems, such as determining the stress in a shaft under load. or the temperature distribution during steady state heat flow. In this discussion only calculations concerned with the flow of fluids in porous media will be considered. The method was introduced by R. V. Southwell in 1935.' THEORY The treatment given here follows that given by Enimons.2 Consider a porous medium to be replaced entirely by a net of tubes of equal length and uniform cross-sectional area as shown in part in Fig. 1. Assume that the net of tubes behaves exactly like the porous medium which it replaces; that is, the net can be made fine enough to reproduce exactly the porous medium. Assume also that Darcy's Law can be used to calculate the flow from one point to another point through these tubes. The flow from point 1 to point 0 is KA . ------ P-P) .......(11 where a is the distance between points: K is the "permeability" of a tube; A is the cross-sectional area of a tube; is the viscosity of the liquid in the porous medium; and (P1 — P0) is the pressure difference between point 1 and point 0. In like manner the flow can be calculated from points 2, 3, and 4 to point 0. The net flow into point 0 is Qo = KA/µa (P1 + P2 + P33 + P4-4P0) . . (2) MB For an incompressible fluid the net flow into point 0 will be zero or, Q. = 0. This says that at point 0 fluid is neither being accumulated nor depleted. 'Therefore. P1 + P2 + P3 + P4 - 4P0 = 0 .... (3) . If. now. with specified boundary conditions. the pressure i.; known at a finite number of points in a given region, as at the points shown in Fig. 1, Equation (3) will be satisfied at every point. If, on the other hand, the pressure is not known, the pressure can be guessed at these points. Then. unless the guess is perfect. Equation (3) will not be satisfied at all of the points. When Equatiol~ (3,) is not satisfietl. let d = P1 + I?, + P, + P, - If' .,....(4) where 6 is an apparent error and is called the residual at point 0. Equation (4) shows how much the pressure guess is in error at point 0 with respect to the surrounding points. A positive residual means that the pressure is too low, and a negative residual means that the pressure is too high. To bring the residual, 6. to zero in order to satisfy Equation (3). it is necessary to make changes in the pressure guesses. Equation (4) shows that a +1 change in Po will change the residual at point 0 by -4. A +1 change in the pressure at any of the four surrounding points will change the residual at point 0 by +l. Thus it can be seen that a change at any point will affect the residual at that point and the four surrounding points. By changing the pressure from point to point, all of the residuals can eventually be brought nearly to zero and the problem will be solved. This procedure is the essence of relaxation methods and is used to relax the residuals so that Equation (3) is satisfied at every point. The procedure can be most easily explained in detail by solving a simple problem. as Southwell says, "To explain every detail of a practical technique is to risk an appearance of complexity and difficulty which may repel the reader. A

Jan 1, 1951

By F. A. Hill

Coal mining in the State of Washington offers many interesting problems for the mining engineer, due to the varied physical conditions occurring in different fields, and often in the same mine. The different coal seams worked in the same mine commonly require different mining and transportation methods for economical operation. The coal measures have inclinations ranging from 5' to vertical, and in the same mine the dip of the coal may vary from 30' to 50 . In all fields, the seams are extensively faulted, folded, and sheared. The quality of the coal produced ranges from brown lignite to bituminous coking coal, the following being typical analyses: Very little of the coal contains as much as 0.75 per cent. sulfur. The brown lignites occur mostly in Lewis and Thurston Counties, and as a rule are very cheaply mined. This coal has been successfully used in locomotives of the Oregon & Washington Railroad, after equipping them with specially designed fireboxes. The sub-bituminous coals occur in all the coal-mining counties. Their cost of production varies widely, according to the character of the formations, the pitch, and the wall conditions. This makes a fairly good steam coal, but the lump is used mostly for domestic trade, after grading into lump, nut, and pea. The coking coal is used for making coke, and for locomotive and other boiler fuel. It yields a strong metallurgical coke, quite high in ash, though seldom exceeding 18 per cent. ash. Most of it is susceptible to

Jan 1, 1920