Search Documents

By E. J. Dulis, R. M. Fisher, K. G. Carroll

IT is well known that ferritic steels containing more than 15 pct Cr when subjected to temperatures in the range of 700" to 1000°F exhibit increasing hardness and decreasing ductility. The phenomenon has been widely termed the "885 °F embrittlement," after the temperature of most marked effect.'.' In view of the excellent review articles available in the literature3-6 only a brief account of experimentally established facts need be given here. The extent of changes in physical characteristics during embrittlement depends on chromium concentration and time at temperature, higher alloy content and longer time both promoting more rapid and extensive changes. In a 27 pct Cr steel, changes in impact strength and in angle of fracture in bending can be detected after only a 1 hr exposure at 885°F; after 50 hr this steel becomes quite brittle. Hardness increases slowly with time during thousands of hours exposure and may attain a maximum hardness number twice as large as that of the unexposed steel. Microstructural changes accompanying embrittlement have been described as an initial widening of grain boundaries followed by eventual darkening of ferrite grains. Embrittled steels etch more readily, e.g., the weight loss of a 27 pct Cr steel in acid solution may occur at a rate one hundred fold greater following exposure at 885 OF. Marked changes which accompany embrittlement have been observed in electrical resistivity, specific gravity, and magnetic coercive force. Changes in physical properties may be readily removed by heating at temperatures above the embrittling range, such as a treatment at 1100°F for 1 hr. It has frequently been noted that the 885 °F embrittlement suggests precipitation on a submicro-scopic scale of a chromium-rich constituent, the nature of which has not been revealed by X-ray diffraction. Progressive broadening of the body-centered cubic diffraction lines during embrittlement has been observed," and recent observations by Lena and Hawkes' upon single crystals have shown early asterism in X-ray photographs, disappearing within an hour at 900 °F. Many workers have ascribed8-13 the phenomenon to a precipitation of a phase (FeCr), which is known to cause embrittling effects at temperatures much higher than 885°F. Two general observations, however. suggest that a precipitation cannot be responsible for the 885°F phenomenon: 1—prior cold work greatly enhances a formation, whereas it scarcely affects the 885 °F embrittlement, and 2—the presence of an alloying element such as nickel or manganese may have an effect on the 885 °F embrittlement which is opposed to its effect upon a formation. The slight enhancement of a formation and 885°F embrittlement observed in the presence of elements with strong carbide and nitride forming tendencies' is probably a consequence of lessened chromium depletion of the matrix. The bar graph in Fig. 1 shows a typical example, taken from two 27 pct Cr steels used in this work, of the hardness after exposure for 10,000 hr at 900°, 1050°, and 1200°F. Steel A (0.03 pct C, 3.13 pct Mn) showed marked hardening at 900" and 1200°F, whereas steel B (0.12 pct C, 0.63 pct Mn) exhibited only the 900°F hardening. The cr phase was found in steel A at the higher temperatures but not in steel B. Presumably a formation is enhanced by the low-carbon and high-manganese concentrations in A," Thus there are two distinctly different hardening phenomena present which cannot both be ascribed to v precipitation without invoking a transition phase possessing remarkable properties. Materials A number of chromium steels exposed for long periods (5000 to 34,000 hr) at 900°F, as well as unexposed samples of one of the steels, were available for this investigation. Table I gives the chemical compositions and aging treatments of these steels. In addition to these steels exposed in the elevated temperature test furnaces of the National Tube Division, a number of high-chromium steels were heated for short periods in small laboratory air furnaces and lead baths. Supplementing these commercial steels, a sample of high-purity (0.018 pct C, 0.002 pct N) 28 pct Cr iron, exposed 1000 hr at 887°F. was furnished by the Union Carbide and Carbon Corp. In addition, an alloy of iron and chromium of high purity containing 46 pct Cr was used. This

Jan 1, 1954

By R. M. Raymond

THE Mining Section of The National Safety Council recently sent out a questionnaire to operators, regarding the class of rope used, specifications required or obtained, factors of safety observed, methods of fastening ropes, lubrication, inspection, and points observed when rope is to be discarded. The answers received from this questionnaire, largely from metal mines, give interesting information, from which recommendations for safety practice on hoisting ropes are drawn. DEPTH OF MINE The depth in the majority of cases noted is from 1000 ft. to 1500 ft. (304 to 457 m.) and records come from a number hoisting from depths of 2000 to 3000 ft. Hoisting is generally done in balance, with a few companies using counterweights. Seldom, more than two shifts are occupied in hoisting. A number of large operators limit the shift for engineers to 6 hr. A few of the larger operators have separate hoists for men and supplies, with a higher class rope for men. The range of loads varies from 7 to 17 tons and greater in a few cases, with a balanced weight of 4 to 7 tons.

Jan 2, 1922

COLLECTIVE bargaining, hereto-fore loudly proclaimed as one of the stout timbers of the Republic, has passed from the picture. The coup de gr[a]ce was struck by the President of the United States when he ignored his vested legal prerogative and seized the steel industry by the dubious authority of, his "inherent powers." Autocratic judgment by a single official replaced arbitration by the steel industry and labor union. This is the outcome of a battle which has been bitterly waged for months in the hazy atmosphere created by well oiled propaganda machines. Prior to government intervention, there was no clear picture of the issues at stake. All parties concerned marshalled their accountants to conjure up figures proving their respective contentions. The results were fed into public relations departments for embellishment and dissemination. Thus, the public was asked to believe on one hand, that the steel worker, who is second only to the coal miner in hourly wages, was entitled to an increase in pay and other benefits. Nothing was said about the effect-of such an increase on the national economy. Industry in turn pointed to declining profits after taxes, but failed to mention the more than a billion dollars spent on plant expansion, in addition to the payment of substantial dividends for 1951. With the intervention of the administration, the immediate issue became clear to freedom-loving Americans. Is the executive branch of the government above the law, or is it supposed to uphold and carry out the .laws of Congress? The present administration forgot that it is a servant of the public and has become despotic. The American people must obliterate this dangerous precedent which has been set by the administration or accept the. ominous consequences of submission. Fortunately, the strongest weapon of the citizen-the ballot -still remains. When democratic procedure is restored, stabilization of the economy will continue to challenge us. This is the main public stake in the steel controversy. Only a solution based on bed-rock democracy will work. If the emergency is real, and we must assume that it is, this is the time for sacrifice. Industry and labor must meet without rancor to resolve wage contracts through collective bargaining. The government role, under emergency conditions, must be to objectively maintain wage, and price ceilings in the interest of stabilization. Political expediency cannot be permitted to' influence these controls. Politics and not the public weal have been the guide lines for too long. We are at the cross roads. By all sober judgment, this is the time for Americans to take a militant interest in their government today. Tomorrow will be too late.

Jan 1, 1952

By Arthur Taggart

THE following conclusions on the work of the Hardinge mill are based on data furnished to the writer by the Hardinge Conical Mill Co. in the form of the mesh cards hereto appended. Energy units (E. U.) and relative mechanical efficiencies (R. M. E.) are computed by the "volume method" of Stadler.1 Screen apertures used are the average apertures of testing screens of the meshes given. Card 122. June 28, 1912. Vipond Porcupine Mines Co., Ltd., Schumacher, Ont., Canada. Ore from mill bin. Gangue, quartz and basalt. 4.5 ft. by 13 in. ball mill. Capacity, 48 tons per 24 hr. Charge, 4,000 lb. balls. Speed, 33 rev. per minute. Horsepower, 15 to 17. Water, 100 per cent. by weight. (50 per cent. ?) Product deslimed and oversize reground-in pebble mill, see Card 113. Feed to mill through 2-in. mesh.

Jan 7, 1915

By Abdul-Fattah K. Kaddou, P. C. Rosenthal

THE authors have studied the problem of temper brittleness in steel1 employing an internal friction method. The specimens are in the form of wire, 14 B and S gage (0.064 in diam), 6 in. long. It was very desirable to have an apparatus to test the wire specimens for temper brittleness without making standard notched-bar Izod or Charpy impact tests. Such a device would have two favorable advantages: the first is that no standard impact specimen would be necessary, thus saving time and labor; the second is that there would be a direct correlation with internal friction results, thus eliminating the size factor if standard impact specimens had to be used. A search was made without result to find a commercial apparatus for this purpose. The literature was surveyed to investigate if such a test had been utilized. No such work has been reported in the literature; however, zapffe2 has described an apparatus used for testing for hydrogen embrittlement in

Jan 1, 1961

By J. R. Mihalisin

Phase changes in as-cast alloys in the Ni2 CoCr-Ni, Ti-NSAl system containing 0.1 wt pct C were studied after heat treatment at 1650°F. It was found that a vegion of CrCo-type s was developed in this system after I1000 hr. The tendency for s formation was dePendent upon the aluminum and litanium content, the s -forming tendency generally becoming more pro-nounced as the latter two elements are increased. s lended to form in interdendritic regioues and was associated with solutioning- of- carbide phases. Electron- vacancy computations for prediction of s formation on these alloys mere in sufficient agreement with what was observed experimentally to indicate that the method should be of value in assessing a-forming potential in cast alloys. However, the correlation of electrotz- vacancy numbers may not be as favorable in cast as cormpared to wrought alloys. THE increasing use of high-temperature alloys for longer times at higher temperatures has resulted in a real need for obtaining information on the phase changes taking place in these alloys since these changes often have a direct effect on properties. This paper reports on a study of the phase changes in Ni-Cr-Co-Al-Ti alloys after prolonged heating at 1650°F. The alloys were selected from the pseudo-ternary system Ni2CoCr-Ni3Ti-Ni3Al and this system was chosen because it is the basis of many of the newer cast commercial superalloys. The attempt here was not to define accurately the boundaries of s formation in the NizCoCr-Ni3Ti-Ni3Al system but to delineate the phase transformations taking place upon heating alloys covering a wide range of chemistries in this system. An addition of carbon was made to all alloys to further simulate commercial alloys. It was hoped that the information generated in this manner would be of more direct use to superalloy designers than an equilibrium diagram approach since commercial alloys generally have outlived their usefulness when equilibrium is attained. EXPERIMENTAL PROCEDURE The alloys were vacuum-melted from carbonyl-nickel pellet, vacuum-grade chromium, electrolytic cobalt, high-purity aluminum and titanium, and spec-trographic-grade carbon.

Jan 1, 1968

By Waldemar Lindgren

THE following pages present data accepted by many geochemists and geologists regarding the succession of minerals and the temperatures of formation in ore deposits affiliated with igneous rocks. They also present the individual views of the author on the composition of the solutions that were active and on the mode of deposition. He does not regard these views as speculations or hypotheses but as forming a well motivated and consistent theory. It is not certain, however, that all investigators will subscribe to them.

Jan 1, 1936

Fred. T. Greene, Rossland, B. C. (communication to the Secretary): At the beginning of his gaper, Mr. Herzig refers to an article of mine in the Engineering and Mining Journal of January 27, 1900. I would like to add that the method de-

Jan 1, 1901

By John L. Watson

A conceptual model (MAGSEP) is described to simulate the beneficiation characteristics of a drum magnetic separator in terms of the probability of an individual grain being recovered in the magnetic concentrate. This probability is determined as a function of particle magnetic composition and magnetic field strength and is modified by particle size and the separator operating conditions. The model predicts the size, magnetic grade and distributions of magnetic and gangue minerals in the concentrate and tailings produced by the drum separator. The configuration of the magnetic concentration circuit may be altered to permit single or double drum units in parallel or series operation. The characteristics of the feed material, in terms of a magnetic parameter, are essential in permitting the determination of individual grain recovery probabilities upon which the model is based. Thus the model requires input data relating to the distribution of composite grains in terms of magnetic grade and particle size. To illustrate the use of the conceptual model an example is given for the beneficiation of New Zealand iron sands.

Jan 1, 1984

By M. R. Tek, M. L. Katz

The flow of fluids in stratified porous systems, in which adjacent layers of the system are in communication over part or all of their common interface, in many instances involves crossflow between layers. A theoretical study has been made of the unsteady-state flow of slightly compressible fluids during depletion of bounded stratified porous systems. Consideration has been restricted to single-phase flow, with negligible capillary and gravity effects. Analytical expressions have been derived for pressure distribution and for (luxes at the producing face in two-layer systems with complete fluid communication between layers. These expressions occur in the form of double Fourier and Fourier-Bessel series. The method of extending the solution to any number of layers is demonstrated by deriving the equation for pressure distribution in a three-layer system. On the basis of the exact results for two-layer systems, certain generalizations regarding the behavior of stratified systems in general are presented. The performance of stratified systems, in terms of cumulative flux as a function of time, is shown to lie at all times between bounds established from single-layer theory. The upper bound is given by treating the system as a single layer with arithmetic average physical properties. The corresponding lower bound is the summation of the fluxes from each layer as treated individually. Variation in performance of stratified systems between the upper and lower bounds is determined by the extent to which crossflow occurs in the system. The principal parameters affecting the amount of crossflow are the vertical permeability of the system, the ratio of system thickness to "radius of drainage" and, for radial systems, the ratio of system thickness to interior radius. At very early times, the system performance is near the lower bound. As time and the radius of drainage increase, the per- formance tends toward the upper bound. INTRODUCTION One of the principal problems confronting the reservoir engineer today is the incorporation of the effect of reservoir heterogeneity into predictions of reservoir performance. The first part of this problem is the characterization of the actual reservoir heterogeneity in a mathematically useful manner.1, 2 It is then necessary to calculate the effect of this heterogeneity on the system performance. It is frequently possible to estimate this effect by comparison with the known behavior of an idealized system. One such idealized system is the stratified or "layer-cake" model. Many studies have been made of the behavior of stratified systems, from both a theoretical and experimental standpoint. The great majority of the theoretical studies have been concerned with systems of separated layers, with no fluid crossflow. Among the more noteworthy of such theoretical papers is that recently published by Lefkovits, et al,3 in which a comprehensive analysis was presented for the behavior of bounded stratified systems which are unconnected except at the wellbore. Three recent references have dealt with stratified systems including the effect of crossflow. Jacquard4 has presented mathematical derivations pertaining to depletion of two layer systems producing at constant rate. A doctoral dissertation by Katz5 contains analytical solutions and tables of results for pressure distribution and fluid flux during constant-terminal-pressure depletion of two-layer and three-layer systems with crossflow, together with tables of eigenvalues necessary in the computations. The dissertation also presents results from experimental studies of stratified systems using a heat-transfer analog model. This paper is largely based on the material in this dissertation. A third paper has been presented by Russell and Prats6 since completion of the work resented herein, containing mathematical derivations for and discussion of the behavior

By Norman C. Stines

Russia's mineral potential is a secret that has been effectively kept by the Iron Curtain. There is no conclusive data and because of its extreme importance to the Free World, the subject is greatly discussed. Opinions range from those presented by Paul Tyler in his article "Russia's Mineral Potential," June issue of MINING ENGINEERING to those of Norman C. Stines, presented herewith. Mr. Stines is a consulting mining engineer of Los Gatos, Calif. He was in Russia, China, and Manchuria from 1909 to 1918 as a mining executive. From 1917 to 1919 he served as assistant military attache Intelligence Branch U. S. Army in Petrograd, Russia.

Jan 11, 1951

By R. F. Krueger, L. C. Vogel

A design is presented for an electrical analog computer which can solve non-steady state heat transfer problems in an extensive radial forrnation containing a moving cylindrical source. The computer is used to simulate a .simplified thermal oil recovery process in which heat transfer from a moving, constant temperature source takes place radially by conduction only. Temperature distribution curves are .shown for several different assumed modes of travel for the heat source. The data are used to estimate the residual fuel requirements necessary to maintain a self-propagating isotherma1 front for the particular system being studied. Although the computer is designed to represent an unique system. conversion factors can he adjusted to show the effects of changing the assumed values of system constants, such as thermal conductivity of the formation and temperature of the source isotherm. Examples are given to illustrate the relative influence the assumed values of these variab1es will have upon the quantity of fuel required to maintain the source. The maximum effect of heat transfer by the flowing air stream is estimated mathematically, and full requirements for this system are shown to he markedly reduced. Inasmuch as the examples discussrd refer to a simplified process, the results are not directly applicable to a practical field operation. It is believed, however, that the data il1ustr-ate some general trends which are important in thermal recovery processes. Data from laboratory and field experimentation can he used to modify the computer to take into account the influence of heat transfer by various mechanisms, for example, by injected air and by fluids ahead of the hot zone. With .such refinements it would be possible to estimate more accurately the limiting values for the rate of travel of the high temperature front and for the required air- injection rates. Use of this computer should aid in evaluating the economic feasibility of oil recovery by various thermal processes. It is hoped this paper will stimulate further work by others to help accomplish this objective. As the costs of exploration for and development of new oil fields rise. increasing the recovery of oil from established fields becomes more and more important. In fields containing low gravity crude oil, ultimate recoveries by primary means are sometimes less than 10 per cent and often total only 10 to 20 per cent of the oil in place. Conventional secondary recovery methods are not always effective in increasing this total. Methods which have been proposed for increasing the recovery of viscous oils include thermal processes for increasing the mobility of the oil. One method is to provide a moving heat source generated within the formation to heat the oil and a flowing gaseous medium (for example, air) to sweep the oil to the producing wells. The possibility of such a process has intrigued engineers for many years.'. '." but little or no information has been available in the literature relative to the technical or economic feasibility of this method. Recently, however, interest has been revived by publication of laboratory and field test results indicating the feasibility of maintaining

Jan 1, 1956

By O. B. Ellis

Although thousands of tons of stainless steel have been used successfully for many types of equipment, there have been few cases of failures due to the phenomenon described as stress corrosion cracking. During the past seven years only six cases of such failures have been drawn to our attention and investigated in the Research Laboratories with which the author is associated. These failures oc¬curred in two coffee urns, two wool con¬ditioning units, one dyeing machine, and another in a part of a steam-jacketed stock pot. In each case the equipment failed in a comparatively short time after exposure to conditions of high humidity at tempera¬tures in the range of 100 to 200 F. The failures in all cases were characterized by general embrittlement and cracking of the stainless steel, with only slight indications of general corrosion except at the cracks. The first failure of this type was a coffee urn returned for investigation in 1937. The top and bottom sections showed a general corrosive attack and embrittlement and cracking of the stainless steel. The chemical analyses of these sections were as follows:

Jan 1, 1945

By Lawrence Burkhart, S. B. Joo

Axially unsymmetric ordered circulation patterns on the surface of a hemispherical constant volume drop with forced Internal motion were considered as a manifestation of hydrodynamic instability, which was affected by internal flow as well as by the properties of the interface A simplified mathematical model was analyzed In order to study the mechanism of onset of interfacial circulation from a non-circulatory basic state. Values of the critical Reynolds numbers were obtained when the basic state became a fully developed rotational flow and the values changed for different interfacial properties. The work describes a heretofore unreported surface flow pattern on drop surfaces From a practical point of new, any motion in the interface of a droplet can have a significant effect of mass transfer rates in solvent extraction processes Although surface motion in droplets actual processing equipment is very complex, continued study of the fundamental nature of such phenomena should ultimately lead to more effective equipment design procedures.

Jan 1, 1981

By Stanley Kesler

The first of two initial 650-mw units of the Paradise Steam Station, located on the banks of the Green River in the south-central portion of the western Kentucky coal basin, is scheduled for operation in late fall of 1962. This plant will be the eighth large-capacity, modern station built by TVA in a series starting with Johnsonville, operated first in 1951. During the subsequent ten years, unit sizes have increased from a capability of 125 mw to 650 mw at Paradise. This new unit will take its place in a power system that serves an area of about 80,000 sq miles with a present installed capacity of over 12,000 mw. Upon completion of the Paradise units and other additional hydro and steam units presently under construction, the system capacity will have reached over 15,000 mw. Projected load estimates indicate that this system will provide a margin of slightly under 10% of dependable capacity above peak demand at that time. One Paradise 650-mw unit at that time will represent approximately 4yc of the total system installed capacity.

Jan 10, 1962

By F. G. Tryon

This paper treats only of the practicability of introducing a standard classification into the records of production and distribution of coal which we try to keep in the Bureau of Mines. From the point of view of gathering and analyzing statistics, the requirements of a satisfactory classification are that it shall be so definite as to eliminate the factor of arbitrary judgment, that it shall be reasonably simple and, finally, and most important, that it shall be understandable to the trade. In other words, to be woven in the statistical record it must be adapted to the raw material which flows in from the 7000-odd mines that produce the coal. The success of any scheme of classification, from the point of view of use, will depend largely on the degree to which it utilizes the accumulated experience of the trade and employs as far as may be possible the accepted trade designations. The experience of the Tidewater Coal Exchange during the war would be an excellent point of departure for a use classification of the coals of the Eastern Appalachians. Although the exchange long since passed out of existence, coal is still quoted and sold by the old pool numbers, and they have shown rather extraordinary vitality. Some years ago, in the Geological Survey, the experiment was tried of getting operators to classify their own coal by offering them a list of standard designations on the annual statistical questionnaire. The results were more amusing than informative. What with the confusion in terminology and the natural temptation to put one's best foot foremost, there was a general tendency to grade up the quality. Floods of semi-bituminous coal flowed in from many sources, millions of tons from districts where not a pound of that quality has ever been produced. The producers of semianthracite in Arkansas almost without exception would report their product as anthracite and their neighbors in the little Paris field, producing a fine blocky house coal averaging about 17 per cent, volatile, would say, "Our coal isn't anthracite; it's a semianthracite." Finally we discontinued the publication of those data as being more misleading than helpful.

Jan 1, 1930

By T. M. Allen, W. H. White

THE Greenwood-Grand Forks area of southern central British Columbia, known as the Boundary District, has a long history of mining exploration and production. At the turn of the century this was the premier copper mining camp in the British Empire, its total production amounting to some 20 million tons. Most of this ore came from the great Granby mines at Phoenix, but the Motherlode mine at Deadwood camp, 6 miles to the west, and several mines in Summit camp, 5 miles north of Phoenix, made important contributions. The large deposits were exhausted in 1918 and the district since has seen only desultory exploration and salvage operations. The orebodies are mineralized skarn zones in limestone members of a thick series of Upper Paleozoic sedimentary and volcanic strata. Chalcopyrite is the primary ore-mineral. Copper carbonates and silicates occur sparingly in outcrops, but the oxidized zone generally is very shallow. Much of the surface is mantled by glacial drift which in most places ranges in thickness from 2 to 15 ft. In some of the hanging valleys, however, the glacial drift may be as much as 100 ft thick and may assume drumlin-like forms. In 1951 an ambitious program aimed at the discovery of new orebodies and important extensions of abandoned deposits was launched by Attwood Copper Mines, Ltd. In this district so thoroughly searched by an earlier generation of prospectors, any orebody which had remained undiscovered must have little or no surface indication. Consequently, in addition to the basic detailed geological work, the program of exploration included magnetometer and self-potential surveys. Geological bets and geophysical anomalies were tested further, prior to diamond drilling, by a study of copper distribution in tree twigs and/or in the soil. The soil sampling and analytical methods used and some of the results seem of sufficient importance to warrant this paper. The authors had done some plant sampling in this and other districts, using the dithizone neutral-color-end-point method (Warren and Delavault, 1948, 1949; White, 1950),1-3 but they were unfamiliar with its soil application. Finally, after much experimenting in the field, they adopted the methods described here. These methods are not entirely original or defensible on theoretical grounds, but under field conditions of rapid sampling and analysis the results are reliable enough to be of use. Fig. 1, which shows the results of duplicate analyses of duplicate soil samples taken at 50-ft intervals across an anomalous zone, indicates the relative dependability both of the sampling and analytical methods. Sampling and Analytical Equipment A 2-ft piece of 1-in. solid drill steel, one end sharpened to a broad, conical point. The steel is marked at 1 ft from the point. A 2-ft piece of ½-in. black iron pipe, one end filed to a bevelled cutting edge. The pipe is marked at 1 ft 3 in. from the cutting end. A 3-lb hammer. A plastic or rubberized sheet about 18 in. square. Moisture-proof assay pulp envelopes. A 10-mesh seive made from window screen with the paint burnt off. A small assay spatula. A pan balance sensitive to 10 mg. Two ignition trays about 4 in. square, made of sheet iron turned up along the edges. A Coleman two-burner gasoline stove. An asbestos board about 5x8 in., used as a hot plate on the gasoline stove. A circular aluminum rack to hold 8 test tubes while refluxing (design of Almond and Morris). Pyrex Glassware Large refluxing test tubes, 25x200 mm, marked at 40 ml volume. Breakers, 20 ml. Pipettes, 1, 5, and 10-ml capacity. Graduate, 50 ml. Shaking cylinders, 100 ml, glass stoppers. Burette, 25 or 50-ml capacity, with holder. Chemical Supplies 1 N sulphuric acid. Hydroxylamine hydrochloride, solid crystals. Fisher Alkacid test paper. Copper standard solution. Dithizone standard solution 60 mg per liter. Water reasonably free of metals. Soil Sampling Method: The problem of how to take a soil sample is extremely crucial. The method outlined below, adopted after a number of tests, has the advantages of uniform pattern, uniform depth, and uniform size of sample. The area to be tested was marked off by chain and compass lines 100 ft apart, normal to the strike of possible ore deposits. Numbered stakes were set at 50-ft intervals along these lines and a soil sample was taken at each stake in the following manner. The drill steel was driven into the ground normal to the slope of the surface to the marked depth of 1 ft, moved slightly from side to side, then carefully withdrawn. The iron pipe was inserted to the bottom of this hole, tapped down to the marked depth of 1 ft 3 in. and withdrawn; the 3-in. soil plug in the

Jan 1, 1955

By John G. Bartram

The oil business has been relatively quiet in Wyoming during 1934. Only 34 producing wells were completed, 54 dry holes were drilled, and at the end of the year only 30 wells are listed as drilling. Wyoming still has a large reserve of production shut in, mostly in black oil or asphaltic base fields in the northwestern part of the state. The total oil production increased from 11,171,500 bbl. in 1933 to 12,539,470 in 1934, but light oil production continued to decline, and the increase was made by black oil fields. This is partly due to natural decline of light oil fields, especially Salt Creek, Big Muddy and Lost Soldier, but largely because of increased demands for road oil. The Rocky Mountain states spent much money to build and improve roads and a greater amount of road oil was used. The refining of black oil to manufacture road oil produced gasoline as a byproduct that slightly decreased the demand for light oil. The Oregon Basin and Frannie fields, in the Big Horn Basin, moved into second and third places in the list of producing fields in Wyoming because of their increased black oil production, and Big Muddy and Lost Soldier, light oil fields, dropped back. Wyoming stayed close to its allowed production, which was based on the needs of the refiners and purchasers. This activity in black oil resulted in a few more wells in the fields of the Big Horn Basin, but the greatest amount of drilling was in the shallow Osage field in eastern Wyoming. Osage supplies many little topping plants and at the close of 1934 there was not enough oil available there to supply all of them. In the Lost Soldier field and Salt Creek, one major company was rather active in a campaign to deepen, clean out and repair old wells to increase production, and the figures of that work are not included here. Of the light oil fields, Lance Creek promises to be most active during 1935, since the two wells in the recently discovered Sundance sand pool are producing and more wells will he drilled. With wildcatting almost at a standstill, two new oil fields were discovered in Wyoming in 1934. In Albany County, a 75-bbl. oil well was completed on Quealey dome in the Muddy sand (Upper Cretaceous)

Jan 1, 1935

By P. K. Weimer

Coinpletely integrated thin-film circuits inco?,porating more than 1000 active and passive elements have been fabricated reproducibly in the laboratory by evaporation of- all components. A 180-stage modified shift register comprising 540 CdSe TFT's, 360 resistovs, and 180 capacitors was deposited upon a glass substrate during one pump-down of the vacuum systeitl. Experimental units have been operated for more than 5000 hr at temperatures uP to 85°C without failure of any slages. The present pupper reviews the charvactevistics of evaporated thin-film transistors (TFT's) and discusses their application to integrnted circuils. INTEGRATED circuits most widely used today are based upon silicon technology, with the circuits formed on the surface of a block of single-crystal silicon1 or on a block of sapphire 2,3 upon which a thin layer of silicon has been deposited. Transistor patterns and interconnections are defined by photographic procedures using photoresist masking. Large groups of transistors are produced in batches which undergo many processing steps, some of which are carried out at elevated temperatures. Passive elements are formed by treatment of the semiconductor surface or are deposited by evaporation alongside the active elements. The size and complexity of the circuits are limited by defects in the devices and by the size of the available single-crystal chips. Capacitative coupling to the semiconducting substrate may also limit useful size and frequency response of the circuits. An alternative approach to integrated circuits is based upon the deposition by evaporation of all circuit components upon a noncrystalline, insulating substrate such as glass.4 Thin-film field-effect transistors,1'6 known as TFT's, can be deposited in large arrays on glass or plastic substrates at the same time the associated passive elements are being deposited. Although still in the research stage the all-evaporated approach is expected to offer certain advantages for many applications. In particular, the use of thin films upon a noncrystalline substrate offers the prospect of producing complex, large-area circuits not now feasible with single-crystal silicon. Important applications of this type include memory arrays for computers and imaging devices for television. The ease with which the evaporated TFT's can be deposited may permit continuous, automated production methods not possible with high-temperature batch processing. Recent advances7'8 in the fabrication of thin-film transistors have led to greatly improved reproduci-bility and life of the TFT's. Experimental circuits having over 1000 active and passive elements deposited upon a common glass substrate are currently being produced in the laboratory. The present paper reviews recent progress in the development of the TFT and in its application to integrated circuits. I) DESCRIPTION OF THE THIN-FILM FIELD-EFFECT TRANSISTOR The TFT is a field-effect transistor of the type having the control gate separated from the semiconductor by a thin insulating spacer. Although its operation resembles that of the silicon MOS transistorg its construction is based entirely on thin-film techniques. Fig. 1 shows a cross-sectional view of an evaporated TFT deposited upon a glass substrate compared with a silicon MOS transistor deposited upon single-crystal sapphire.3 The semiconductor in the TFT is a poly crystal line layer, of a material which can be readily evaporated, such as cadmium sulfide, cadmium selenide,l0 or tellurium." Silicon monoxide layers have usually served as the gate insulator, but other oxides, sulfides, and fluorides may be used. Film thicknesses range from a few hundred to a few thousand angstroms. The source, drain, and gate electrodes in the TFT are of metal. Qpical source-drain gap dimensions are 0.0003 x 0.030 in., with a gate strip whose width slightly overlaps the source and drain. The source and drain electrodes should make low impedance contacts to the semiconductor. With cadmium sulfide films, gold is a satisfactory material for underlying electrodes, while aluminum is preferable for overlying electrodes.12 Considerable variation in design of the TFT is permissible, with the electrodes being

Jan 1, 1967

By H. D. Hoskold

As the theory and the practice of valuing mines have never been discussed in the Transactions, a paper on the subject may be acceptable, even though not exhaustive. The method here indicated is set forth, not as a model of perfection to be followed absolutely, to the exclusion of any other system based on sound scientific, commercial and equitable principles, but merely as an aid to mining engineers and financiers in estimating the value of mining-property. This paper is intended merely to point out certain financial features of the question, and not at all to go into the theories of the formation of mineral veins, extremely valuable as it must, of course, be to understand the laws of the earth's formation and of its various changes, which are the basis of such important sciences as geology and mineralogy, and highly useful as guides in determining the probable existence and extension of mineral deposits. Financial Elements of Mine- Valuation. The practice of basing the stock-exchange price of mining shares upon reports, periodically received from the mine-captain or manager, stating that in his opinion the mine is " improving " in this or that level, and is worth so much " per fathom," is, of course, absurd. Everybody experienced in metalliferous mining is aware that a mineral vein varies in thickness and also in percentage of metal in different parts of the same mine. According to the practice just indicated, a mine must have had as many values a per fathom " as there have been given reports upon it at intervals during the year,

Jan 1, 1903