Search Documents

By Tom W. Pfeifle, Paul E. Senseny

INTRODUCTION Engineered structures such as mines, shafts and tunnels, and storage caverns for hydrocarbons, chemical s and brine are being built in natural rock salt formations in increasing numbers. In addition, salt formations are being considered as potential hosts for mined, nuclear waste repositories. The popularity of these formations for engineering purposes stems from the many favorable commercial, physical, and thermal characteristics attributed to the material itself. Not only have the formations been stable and free of dissolution for hundreds of millions of years, but the salt is fairly easily mined and has very low permeability, low water content, and high thermal conductivity. Another characteristic of salt is its tendency to flow or creep when subjected to a shear stress. Although this behavior may be desirable in certain instances, it may be detrimental in other instances since the creep rate may be large enough to produce deformations that tend to reduce the volume of storage caverns or to restrict access to mining operations. In either case, the engineer is faced with the problem of accurately predicting the long-term structural deformations under various combinations of stress and temperature and is required to compare these deformations with long-term design criteria. In the laboratory, deformation-versus-time curves obtained at constant stress and temperature show that creep of salt is similar to creep of many other crystal line solids. Figure 1 shows a typical deformation-versus-time curve for salt. When a shear stress is first applied, the rate of deformation is high, but decreases monotonically. This initial behavior is called transient or primary creep. At some time, the deformation rate no longer decreases but continues at a constant rate. This behavior is called steady-state

Jan 1, 1982

By K. G. Gorling, S. J. Wallden, N. B. Lindvall

It is the policy of The Metollurgical Society to provide, in the TRANSACTIONS OF THE METALLURGICAL SOCIETY OF AIME, a prompt and accurate medium for publication of reports of significant new research in both the scientific and engineering aspects of metallurgy. Papers submitted to the Society are judged by competent reviewers according to established criteria for technical merit, accuracy, originality, and presentation. STAFF: Editorial Director, Rixford A. Beals; Associate Editor, James J. Burke; Assistants, L. Capria and R. K. Larkin. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: A. W. Thornton, Choirmon; Dennis Carney, John Chipman, J. C. Fulton, J. H. Hollomon, H. tl. Kellogg, A. E. Lee, R. Maddin, J. D. Sullivan, and O. Swan. Review and selection of manuscripts is under the supervision of the following Publications Committees: Extractive Metallurgy Division T. B. King. Cha~rmon; S. J. Dickenson, R. P. Hermsdorf, R. Schuhmann, Jr.. and P. T. Stroup. Institute of Metals Division: Robert Maddin, Chairman. F. Lincoln Vogel, Jr., Vice-chairman, W. A. Backofen, R. W. Balluffi, J. H. Bechtold, M. B. Bever, R. S. Busk, C. G. Goetzel, Paul Gordon, C. D. Graham. Jr., Robert F. Hehe-mann, R. I. Jaffee, F. E. Jaumot, Jr., lrving R. Kramer, A. J. Leno, Horold Margolin, C. J. McHorgue, Russell A. Meussner, J. 6. Newkirk, H. W. Paxton, G. E. Pell~ssier, I. S. Servi, Alan U. Seybolt, A. J. Sholer, and Sack Wahsburn. Iron and Steel Division: J. C. Fulton, Chairman; T. B King, F. C. Langenberg, W. O. Philbrook, and T. B. Winkler. Published bimonthly by the American Institute of Mining Metallurgical and Petroleum Engineers Inc., 29 West 39th Street, New York 18, N. Y. Telephonne pennsylvania 6-9220.Petroleum Subscription Engineers$20 per year for non-AIME members in United States and North South and Central 6-9220.SubscriptionAmerica $25 toreign; $5 for AIME members. Single copies, $4.00, iinalo copies Southfpr;ign,andCentral $5 00. The AIME 'is $25not responsible for any statement made or opinion expressed in its publications Copyright 1958 1958 by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. . Registered coble address, AIME New York . . . Indexed in Engineering Index, Industrial Arts Index, ...and Chemical Abstracts . . . Application for second class mail privileges IS pending at New Yark, N. Y. Volume 212, Number 2.

Jan 1, 1959

By J. van Lookeren

In the case of a reservoir where the oil underlies a large gas cap and overlies bottom water, production can be inzproved considerably if wells are perforated below the water-oil contact rather than opposite the oil-bearing section. The theoretical arguments for this improvement, which in some cases may be tenfold, are supported by experimental evidence. INTRODUCTION Reservoirs frequently consist of one sand body containing an oil layer underlying a thick, gas-bearing section and overlying bottom water (Fig. 1). Wells in such reservoirs are customarily opened up opposite the oil-bearing interval or, rather, opposite the lower part of this interval (Fig. 2). More often than not, it is inefficient or prohibited to blow off large quantities of gas with the oil. This im-psses a severe limitation on the drawdown, which results in low oil-production rates. Because of the small difference in specific gravity between oil and water, the latter will easily cone upwards, so that the production of water together with the oil is not prevented by this completion method. In such a situation wells should be opened deeper, in the originally water-bearing zone. The gas can be shut off by not perforating over the upper part of the interval (Fig. 3) or by a tubing hung close to the bottom of the interval (Fig. 4). Initially much water will be produced, but when steady-state conditions have been established (as depicted in Figs. 3 and 4) larger drawdowns are permissible than in a conventionally completed well, and correspondingly higher oil-production rates will result. Water cuts are only slightly higher because of the small effect of gravity on the water-oil flow distribution. CALCULATIONS The ratio of improvement has been estimated by means of approximate calculations. The completion depicted in Fig. 4 is the most convenient basis for these calculations. By postulating that vertical flow gradients can be disregarded, the Appendix shows that the well-known Dupuit formula can be obtained except for some complication due to the presence of two fluids rather than one. The Appendix makes the reasonable assumption that, for suitable boundary conditions, the oil layer occupies a constant fraction of the total fluid height throughout the reservoir. The oil- and water-production rates can thus be related to the liquid levels in the borehole as follows:

Jan 1, 1966

By G. A. Croes, N. Schwarz

The dimensionless groups, to which the variables that govern the displacement of oil from reservoirs by liquids can be combined, are derived. Three types of displacement are considered, viz. cold-water drive, hot-water drive and solvent injection. The derivation of the dimerzsionless groups is carried out by means of the relevant basic equations (in-spectional analysis). The resulting sets of groups are afterwards completed by means of dimensional analysis. The form of the groups is given in such a way that they can be adapted to suit the various boundary conditions that are encountered in practice. The physical meaning of the groups is discussed. They have all been brought together on a chart, from which their mutual relation and their corresporzdence to related dimensionless groups in common use in other engineering sciences can be read off. The limitations of dimensionally scaled model experiments as a useful tool for studying liquid flow in porous media, as occurring in oil reservoirs, are discussed. The use of models to study fluid mechanics has an appeal for everyone endowed with natural curiosity. What active boy has not played with ship and airplane models, or crude models of dam and drainage systems Even in the most advanced technical engineering, such models play a fundamental and indispensable role. "And yet in few departments of the physical sciences is there a wider gap between theory and practice, between scientific knowledge and the state of art, than in the use of models to study hydrodynamic phenomena." Garrett Birkhoff1 INTRODUCTION Laboratory displacement experiments are extensively used to investigate, directly or indirectly, the production behavior of petroleum reservoirs. Such experiments are representative of the reservoirs as a whole, if they are carried out with models that are "properly scaled." The performance of oil reservoirs is governed by the values of a number of variables, which can be combined to dimensionless groups. Two general methods are available for the derivation of these groups. In the first of these, dimensional analysis, combination of the variables is done essentially by trial and error. Its only premise is knowledge of the complete set of relevant variables. In the second method, inspectional analysis, the dimensional homogeneity of the equations describing the behavior of the system to be studied is used. The resulting dimensionless groups can be divided into: (a) independent (variable) groups, such as dimensionless length, time, etc.; (b) dependent groups, giving the dimensionless form of the variables, such as recovery and pressure, that can, at least in principle, be measured during an experiment; (c) similarity groups, which are independent constant groups, such as ratio of length to height of the reservoir and ratio of

Jan 1, 1957

By J. R. Low, M. B. Reynolds, L. O. Sullivan

The effect of neutron bombardment upon the stability of type 347 austenitic stainless steel has been investigated by a magnetic technique. The relation of the ferrite content of a stainless steel to its magnetic properties is given, and an apparatus suitable for the measurement of the ferromagnetic saturation induction of small specimens is described. Results of measurements on irradiated specimens are tabulated. Exposure to a neutron flux was found to cause a slight increase in the ferrite content of type 347 stainless steel, the change increasing with increasing length of exposure and with increasing initial ferrite content. The similarity of the effect of irradiation to the effect of annealing is pointed out. Possible effect of irradiation upon density of austenitic stainless steel is discussed. COMMERCIAL austenitic stainless steels are alloys of iron, chromium, and nickel, plus small quantities of other elements. Although these alloys are normally used in the austenitic condition, this state is thermodynamically metastable at ordinary temperatures and transformation to a more stable state takes place under favorable conditions. In the austenitic state, these stainless steels have the face-centered-cubic crystal structure characteristic of y iron, but the stable state at room temperature is a mixture of austenite and body-centered-cubic ferrite. The transformation from the pure austenitic condition may be brought about by cold working the alloy at a temperature below that at which the aus- tenite becomes thermodynamically unstable (about 400°C), the completeness of transformation increasing with increasing severity of cold work and decreasing temperature. The behavior of the austenitic stainless steels under ordinary conditions of use is rather well known. However, use of these alloys in a nuclear reactor introduces a new variable: the effect of neutron bombardment upon the transformation from the austenitic to the ferritic state. It was with this in mind that a study of the radiation stability of austenitic type 347 stainless steel was undertaken. Magnetic Technique for Ferrite Determination Commercial austenitic stainless steels such as type 347 undergo little transformation under normal conditions of fabrication and use. In view of this fact, it seemed likely that neutron irradiation would change the ferrite content of the alloy but little. The method chosen for measurement of the effect of neutron irradiation was thus limited to one which would be quite sensitive to small changes in the ferrite content of the alloy. Of the properties of the stainless steel which can be measured, the magnetic characteristics are most sensitive to the quantity of ferrite present.

Jan 1, 1956

By Robert Warner

The growing importance of screening makes an accurate measure of the quality of a sizing operation desirable. Screen efficiency is considered equal to the percentage of true undersize in the feed obtained as undersize from the screen. This method is unreliable, as it gives the same credit for removing minus 200-mesh material as for removing material just able to pass the aperature of the screen. A more accurate measure of screen efficiency is to consider only the work done on the "difficult" grains, that is, those grains of which the intermediate diameters closely approach the screen aperture.. The application of this method is given, together with the derivation of formulas and an example of their use. Is AN accurate measurement of the efficiency of a screen under a given set of operating conditions valuable? If so, what is the efficiency; of, a screen and how can it be measured? Sizing, especially of the finer sizes of material, has increased in importance in the development of flow sheets as a result of the perfecting of the rapid vibrating screens. More consideration should be given screens in the preparation of ball-mill feed, where they permit the admission of a dryer feed than, the classifier. Where possible, the introduction of a screen ahead of the primary ball-mill, and the diverting of ore below, say, 4 mm. to a secondary mill, might result in a greater overall economy because of the thicker feed and the better, adjustment of crushing media and mill operation to the reduction demanded. With the present trend back toward a combination of gravity methods and flotation, rather than flotation alone, the accurate, economical sizing possible with the new screens makes fine jigging a method to be considered. W. 0. Borcherdt1 and John Bland2 discuss the screening problem and also the value of close sizing in the concentration of some of the rare-metal ores. If a screen is to be used, it should be selected in competition with others; other things being equal, that screen which makes the cleanest oversize should be preferred. The quality of the screening and the tons

Jan 1, 1924

Establishment of a Bureau of Mineral Research at the Michigan College of Mining and Technology, initiated by the State of Michigan with legislation in 1951, is moving toward realization. The Michigan Legislature appropriated $24,000 to cover preliminary costs of plans and specifications for "engaging in a broad, widespread study of the beneficiation of lowgrade ores, of ore dressing, and all the problems of metallurgy that enter into such a program." Ralph C. Calder, of Detroit, who designed Michigan Tech's campus buildings, is preparing plans for the proposed Ores Research Building. Members of the college staff, Professors F. J. Tolonen, W. E. Keck, and Research Engineer Paul Jasberg are assisting in preliminary planning. C. Harry Benedict, retired chief metallurgist of Calumet and Hecla and a member of Michigan Tech's Board of Control, is assisting with technical details. Professor Nicholas Manderfield, head of the department of Mineral Dressing, was assigned to visit other research installations and suggest plans for the Bureau.

Jan 1, 1952

By Horace Winchell

SCOPE OF DISCUSSION THE laws here referred to Are those which define the status of the prospector for mineral deposits in the soil or beneath it, establish his methods of procedure, protect him in his possession while searching for the subterranean treasures, and give him assurance of title when all required conditions have been fulfilled and valuable minerals discovered. Regulations for the operation of mines and the safety and health of mine employees are likewise subjects of Federal and State legislation, but are not within the scope of the present program. Various features of our present laws will be discussed in detail by able students of the subject, and specific remedies will be proposed for the most glaring defects. It is my purpose to present in this paper a summary review of the reasons why revision is needed and demanded by the great majority of those in daily contact with the industry.

Jan 4, 1914

By Kenneth C. Vincent, A. M. Gaudin

In a study1 of the action of amyl xan-thate on chalcocite in water suspension, it was found that if the xanthate is added in relatively large quantity the xanthate group can be accounted for in three forms: (1) as xanthate ion remaining in water, (2) as benzene-soluble cuprous xanthate on the chalcocite, (3) as a benzene-insoluble coating on the chalcocite. Reduction in the amount of xanthate added leads to disappearance of form I then of form 2. With minute quantities of added xanthate, substantially all the reagent is of the "unleachable" kind. Yet this unleach-able xanthate can be dissolved by pyridine to form a soluble cuprous xanthate complex, and it is sufficient in effectiveness to make chalcocite flotable even if insufficient in quantity to form a complete mono-molecular film on the mineral. In that study it was also found that chalcocite abstracts cuprous xanthate from benzene so1ution, in what may (or may not) be a case of molecular adsorption. It seemed desirable, therefore, to study further the "unleachable" xanthate on the chalcocite, and particularly to ascertain whether it is formed as a result of the benzene leach or is actually formed during the conditioning of chalcocite in aqueous xanthate solution. A 'splendid tool to make such studies has recently been perfected; that is, the use of radioactive spies or tracer atoms. With this tool, it was thought possible to answer the problem stated above, but, unfortunately, this did not prove to be true. Answer to the flotation question was clouded by the existence of rapid and selective diffusion of copper atoms in the solid mineral—a phenomenon that was totally unexpected yet remains interesting and perhaps important. Method of Radioactive Spies The method of radioactive spies is discussed in many places. Two convenient references are the article by Evans2 and the book by pollard and Davidson.3 The method was first developed by van Hevesy and paneth in 1013, when only natural radioactive isotopes were available. These isotopes are few in number, and so the method remained limited in scope. Recently the synthesis of over 350 active isotopes of all the known stable chemical elements4 has opened widely expanded possibilities for the method, A fundamental tenet of the method is that a radioactive atom and a nonradio-active atom are exactly alike until disintegration of the radioactive atom. Then, by its sudden death, the spy reveals its location. The relative abundance of spies at various locations makes it possible to ascertain the relative abundance of the corresponding nonradioactive atoms at the same times and locations. A second fundamental tenet of the method of radioactive tracers is that the radioactivity lies in the nucleus of the atom: transfer of radioactivity from one

Jan 1, 1947

By Kenneth C. Vincent, A. M. Gaudin

In a study1 of the action of amyl xan-thate on chalcocite in water suspension, it was found that if the xanthate is added in relatively large quantity the xanthate group can be accounted for in three forms: (1) as xanthate ion remaining in water, (2) as benzene-soluble cuprous xanthate on the chalcocite, (3) as a benzene-insoluble coating on the chalcocite. Reduction in the amount of xanthate added leads to disappearance of form I then of form 2. With minute quantities of added xanthate, substantially all the reagent is of the "unleachable" kind. Yet this unleach-able xanthate can be dissolved by pyridine to form a soluble cuprous xanthate complex, and it is sufficient in effectiveness to make chalcocite flotable even if insufficient in quantity to form a complete mono-molecular film on the mineral. In that study it was also found that chalcocite abstracts cuprous xanthate from benzene so1ution, in what may (or may not) be a case of molecular adsorption. It seemed desirable, therefore, to study further the "unleachable" xanthate on the chalcocite, and particularly to ascertain whether it is formed as a result of the benzene leach or is actually formed during the conditioning of chalcocite in aqueous xanthate solution. A 'splendid tool to make such studies has recently been perfected; that is, the use of radioactive spies or tracer atoms. With this tool, it was thought possible to answer the problem stated above, but, unfortunately, this did not prove to be true. Answer to the flotation question was clouded by the existence of rapid and selective diffusion of copper atoms in the solid mineral—a phenomenon that was totally unexpected yet remains interesting and perhaps important. Method of Radioactive Spies The method of radioactive spies is discussed in many places. Two convenient references are the article by Evans2 and the book by pollard and Davidson.3 The method was first developed by van Hevesy and paneth in 1013, when only natural radioactive isotopes were available. These isotopes are few in number, and so the method remained limited in scope. Recently the synthesis of over 350 active isotopes of all the known stable chemical elements4 has opened widely expanded possibilities for the method, A fundamental tenet of the method is that a radioactive atom and a nonradio-active atom are exactly alike until disintegration of the radioactive atom. Then, by its sudden death, the spy reveals its location. The relative abundance of spies at various locations makes it possible to ascertain the relative abundance of the corresponding nonradioactive atoms at the same times and locations. A second fundamental tenet of the method of radioactive tracers is that the radioactivity lies in the nucleus of the atom: transfer of radioactivity from one

Jan 1, 1947

By Milton C. Neul

As recently as the mid-1930's, steam and rail haulage were still the primary means of moving large quantities of rock. However, 2- to 5-ton standard on-highway trucks were beginning to be used in the mining industry's efforts to lower haulage costs. It was quickly obvious that rubber-tired equipment was more flexible, faster and more maneuverable. The trend towards haulage trucks had begun. Now while savings were being realized, the severe operating conditions encountered in open pit operations proved too much for the lightly constructed frames, gasoline engines and highly inflated tires. As a result, a few years later, the first 10 to 15-ton, two-axle heavy duty trucks were designed specifically to operate under off-highway conditions.

Jan 3, 1966

By Kenneth C. Vincent, A. M. Gaudin

IN a study1of the action of amyl xanthate on chalcocite in water suspension, it was found that if the xanthate is added in relatively large quantity the xanthate group can be accounted for in three forms: (1) as xanthate ion remaining in water, (2) as benzene-soluble cuprous xanthate on the chalcocite, (3) as a benzene-insoluble coating on the chalcocite. Reduction in the amount of xanthate added leads to disappearance of form 1 then of form 2. With minute quantities of added xanthate, substantially all the reagent is of the "unleachable" kind. Yet this unleachable xanthate can be dissolved by pyridine to form a soluble cuprous xanthate complex, and it is sufficient in effectiveness to make chalcocite flotable even if insufficient in quantity to form a complete monomolecular film on the mineral. In that study it was also found that chalcocite abstracts cuprous xanthate from benzene solution, in what may (or may not) be a case of molecular adsorption. It seemed desirable, therefore, to study further the "unleachable" xanthate on the chalcocite, and particularly to ascertain whether it is formed as a result of the benzene leach or is actually formed during the conditioning of chalcocite in aqueous xanthate solution. A splendid tool to make such studies has recently been perfected; that is, the use of radioactive spies or tracer atoms. With this tool, it was thought possible to answer the problem stated above, but, unfortunately, this did not prove to be true. Answer to the flotation question was clouded by the existence of rapid and selective diffusion of copper atoms in the solid mineral-a phenomenon that was totally unexpected yet remains interesting and perhaps important. METHOD OF RADIOACTIVE SPIES The method of radioactive spies is discussed in many places. Two convenient references are the article by Evans2 and the book by Pollard and Davidson.3 The method was first developed by Von Hevesy and Paneth in 1913, when only natural radioactive isotopes were available. These isotopes are few in number, and so the method remained limited in scope. Recently the synthesis of over 350 active isotopes of all the known stable chemical elements4 has opened widely expanded possibilities for the method. A fundamental tenet of the method is that a radioactive atom and a nonradioactive atom are exactly alike until disintegration of the radioactive atom. Then, by its sudden death, the spy reveals its location. The relative abundance of spies at various locations makes it possible to ascertain the relative abundance of the corresponding nonradioactive atoms at the same times and locations. A second fundamental tenet of the method of radioactive tracers is that the radioactivity lies in the nucleus of the atom: transfer of radioactivity from one

Jan 1, 1944

By Joseph Jensen

When the legal holders of Government permits in the Middle dome of Kettleman Hills entered into an agreement on May 27, 1929, to suspend all drilling activities on five permits, covering portions of the Kettleman Hills Middle dome, until Jan. 1, 1931, and the owners of fee lands contiguous thereto assured Secretary Ray Lyman Wilbur, of the Department of the Interior, that they too would respect a drilling suspension for a period of a little more than 19 months, none of these interested parties realized that this was the first step in a chain of events that would culminate, more than four years later, in the formation of the Middle Dome Corporation for the development of the Middle dome area in a unit plan that would be the first unit plan to be approved by the California Regional Producers Committee and recommended to the President as a satisfactory unit plan, under Section 7 of Article III of the Oil Code, approved Aug. 17, 1933. Neither did they realize that more than two million dollars would be spent before oil or gas would be successfully and continuously produced from wells drilled on that Middle dome area. On Oct. 1, 1933, under the terms of the Middle Dome Agreement, the Middle Dome Corporation assumes control of activities and is responsible for the division of all product's produced from the Middle dome area to members of the Middle Dome Corporation. This Middle dome plan is the second successful unit plan developed in California in the past three years, the first being the Kettleman North Dome Associationll formed under the agreement, of Jan. 31, 1931, for the unified operation and development of more than 12,000 acres of land on the North dome of the Kettleman Hills. All other unit plans discussed in the past four years in the state have not yet been completed, for one reason or another, but under Section 7 of Article 111 of the new Oil Code numerous plans of development, some of which may be unit plans, will be forthcoming within the next few months. There is much

Jan 1, 1934

By L. L. Newman

As soon as the Congress recognized the alarming rate at which our domestic oil resources were being depleted during the war, it took action to step up the rate of research and development which the Bureau of Mines had been conducting for several years on the production of synthetic liquid fuels from coals. Under Public Law 290, approved April 5, 1944, funds were authorized for the Bureau to proceed with research, development, design and construction of demonstration plants for the hydrogenation of coal, the synthesis of oil from carbon monoxide and hydrogen, and the distillation of oil from shale. During the latter part of 1944, when it became evident that the collapse of Germany was near, a Technical Oil Mission was organized to study the Ger- man techniques of synthetic oil production. Since the cost of hydrogen or synthesis gas is one of the major factors of expense in the operation of hydrogenation or synthesis gas processes, the Bureau of Mines considered it of prime importance to include on the mission gas engineers whose instructions were to examine closely the methods employed by the Germans in solving the problem of providing low- cost hydrogen or synthesis gas for their very extensive operations on synthetic liquid fuels. The Solid Fuels Mission and the Utilities Mission, as well as the Army and Navy Missions, also included teams for the study of German gas production. Although their objectives naturally differed from those of the Technical Oil Mission and from each other, it was recognized that there was considerable overlapping of their fields of investigation. Duplication of effort, however, was largely avoided through the close cooperation between the group leaders of these missions. For example, although I went to Europe as a member of the Technical Oil Mission, my first German assignment was actually made by Dr. Harry F. Yancey, leader of the Solid Fuels Mission- to investigate the brown-coal gasification methods in central Germany. The art of gasification in the United States and England, and to a large extent in the proximity of the coking-coal regions of Germany and the rest of continental Europe, depends essentially on two stages of operation; namely, carbonization and intermittent water-gas generation. As far as the United States is concerned, complete gasification in a single stage of operation is rarely practiced, except in gas-producer operations where the product is a relatively lean gas consumed close to the point of manufacture, and for water-gas production with anthracite as a generator fuel. Complete gasification of bituminous coal has been the subject of numerous investigations. Many relatively simple modifications of the water-gas generator have been tried to permit the direct gasification of low-cost bituminous coal instead of high- cost coke and anthracite for the production of water gas. Although varying degrees of success have been achieved and the water gas produced generally has been higher in calorific value, in only a few isolated in- stances has there been any sustained use of bituminous coal for water-gas production for public utility uses after the shortages of anthracite and coke have been lessened.

Jan 1, 1946

By A. W. Ruff

In the last ten years large gains have been made in the field of blasting. These gains have been both in the theoretical and in the practical application of explosives. One of the most publicized changes in the practical application of commercial explosives is the now-prevalent use of ammonium nitrate and fuel oil. The new water-compatible mixture of ammonium nitrate and TNT should also have a large field of application. Most of the theoretical gains have been concerned with the actual rock breakage obtained with explosives. In the last ten years, large gains have been made in the field of blasting. These gains have been both in the theoretical and in the practical application of explosives. One of the most publicized changes in the practical application of commercial explosives is the now prevalent use of ammonium nitrate and fuel oil. The new water-compatible mixture of ammonium nitrate and TNT should also have a large field of application. Most of the theoretical gains have been concerned with the actual rock breakage obtained with explosives. EXPANDING-GAS-BUBBLE THEORY There has been an outstanding change in the conception of how an explosive produces rock failure. The early theory which explained rock breakage was correct for some of the first force-producing agents such as quicklime. When a drillhole was filled with quicklime and water added, the material expanded and steam was generated. The expanding material and the steam exerted a slowly increasing pressure on the sides of the drillhole. The force broke the rock by splitting. Because a great quantity of gas was produced by the deflagration of gunpowder, the same process of the gas pressure splitting the rock was assumed to take place. Even after 80 years of use, the rock-breaking action of all high explosives was thought to be caused entirely by the expanding gas bubble which tore and split the rock. Fig. 1 shows a vertical section through an exploding spherical charge of high explosive. It illustrates the early theory which attributed the entire breakage to the expanding gas bubble. The basic idea of this theory is that the breakage started at the explosive charge and progressed toward the free face. REFLECTED-WAVE THEORY me expanding-gas- bubble theory has gradually been replaced by the reflected-wave theory. The reflected-wave theory explains rock failure by explosives in the following manner: The enormously high gas pressure in the drillhole produces fracturing of the rock on the sides of the drillhole. The fracturing around a 1 1/2-in. diam drillhole is usually confined to an area with about a 6-in. diam. In the fractured area, the pressure of the gas is reduced until the force on the walls is no longer capable of fracturing the rock. Although the gas pressure does not continue to fracture the rock, the pressure imposes a high impact stress on the wall rock. In addition, a pressure or seismic pulse is produced in the rock. The pulse is probably entirely a compression pulse when originally produced in the rock. But, with distance, part of the energy of the compression pulse is transformed into a tension pulse which follows the compression pulse. The explosive charges and burdens used in conventional mine blasting are such that the tension pulse of the original wave is probably too small to be considered in a practical evaluation of the theory. The compression pulse is transmitted through the rock with no associated fracturing.

Jan 1, 1961

By John S. Johnson, Thomas Fraser

SIZING is the process of separating mixed particles into groups of particles all of the same size, or into groups in which all particles range between certain definite maximum and minimum sizes. In coal preparation, sizing is generally accomplished by passing the coal over screens. Separation by differential settling in air or water currents has been adapted to the special field of separating very fine sizes, and these processes are in commercial use to a relatively small extent in the coal industry. Separation with screens is a very old industrial practice. Agricola described the use of screens for ore treatment in the middle ages. In the literature of the British coal industry references were made to the screening of coal as early as 1589, but the practice of extensive sizing for the market did not become general until the last half of the nineteenth century. In America, the practice of sizing developed first in the Pennsylvania anthracite region, beginning with the use of rakes in the mine working places to recover coarse coal. This mining procedure left the fines in the mine. Preparation outside the mine started with the installation of stationary cast-iron plates with 4 to 6-in. square holes. The run-of-mine coal was dumped upon the platforms, the large pieces of rock were picked out by hand, and the large lumps of coal were broken with hammers. The term "breaker," which still applies to the anthracite-preparation plant, originated with this practice, but the term is no longer descriptive of the entire function of the plant. In 1884, the first power-operated anthracite coal breaker was erected by Gideon Bart at his colliery at Wolf Creek near Minersville, Pa. This plant utilized a system of rolls for breaking the coal and revolving screens for sizing. The plant was driven by a steam engine. It could handle coal at the rate of 200 tons a day. By 1860, revolving screens were in wide use in the Pennsylvania anthracite field. Shaking screens were introduced in the Pennsylvania anthracite region in the 90's and they rapidly displaced the lower-capacity revolving screens.

Jan 1, 1950

By Claudio Barsotti, Leonard C. Kitchener

INTRODUCTION The major mining operations of the Ontario Division of Inco Metals Company are located in the Sudbury Basin. Around the rim of this geo- logical formation and within thirty miles of the City of Sudbury are located eleven under- ground mines of the Company, two of which are on standby. In addition, there is one mine in Northwestern Ontario at Shebandowan, 1127 Km (700 miles) northwest of Sudbury. In 1980 ore production totalled 10.6 x 10 mt (11.7 million tons) from underground and open pit operations. Underground mining methods include blasthole, vertical retreat, sublevel caving, cut-and-fill and undercut-and-fill. Inco reduction operations in the Sudbury area include two concentrators, one smelter, one iron ore recovery plant, a copper refinery a nickel refinery and a high purity plate rolling mill. As well, an electrolytic nickel refinery is located on Lake Erie at Port Colborne, near Niagara Falls. In the Sudbury District, Inco employees total 14,278 of whom 6,490 are directly employed in the mining and milling operations. I T H DRILLING Background - The use of long blastholes in underground operations at Inco mines in the Sudbury district started more than 30 years ago at the Levack Mine. At that time, diamond drills were used to mine ore by open stoping and for pillar recovery. By the 1950's the concept had been extended to all mines. The heavy percussion drill was also developed by this time and led to the acceptance of the 11.43 cm (4% in.) piston diameter drifter for bar and arm and fan drill applications. The use however, of the nominal 5.08 cm (2 in.) diameter blastholes drilled radially from the level or sublevel causes overdrilling at the periphery. As well, the smaller holes are subject to hole deviation, are difficult to drill beyond 38.1 m (125 ft.) and require the need for several drilling horizons or sublevels. The need to improve blasthole stoping techniques and our experience with large diameter blastholes in open pit mining led to the trial of an I T H drill in 1962. The test was unsuccessful however, since button bits were not available at the time and the tungsten carbide cross bit experienced short life, gauge loss, and caused hole deviation and poor penetration rates. The successful application of the raise borer beginning in 1964 and the ability to drill 20.32 cm (8 in.) to 27.94 cm (11 in.) diameter pilot holes led to the development of smaller, more portable, rotary drills for blasthole mining. As a result, a mining method based on the use of 20 cm (7 718 in.) diameter, 60.1 m (200 ft.) long rotary blastholes was developed and tested successfully at our C.C.North Mine. Between 1972, when the method was first tested, and 1973 over 4572 m (15000 ft.) of large holes were drilled with rotary drills in the recovery of 175,960 mt (194000 tons) of primary stoping and pillar remnants. A new mining method was developed that made use of this large hole drilling equipment. Instead of longhole carbide drilling by bar-and-arm or fan drill set-ups at sublevels, the large diameter holes were drilled full stope height from the top sill, which substantially reduced development, drilling time and improved fragmentation. These drills however, were difficult to move and set-up, and had a high maintenance cost and low productivity. The capital outlay and extensive technical development required to improve these drills and reduce the high drilling costs however, was economically unattractive. New development in drills and button bits INTRODUCTION The major mining operations of the Ontario Division of Inco Metals Company are located in the Sudbury Basin. Around the rim of this geo- logical formation and within thirty miles of the City of Sudbury are located eleven under- ground mines of the Company, two of which are on standby. In addition, there is one mine in Northwestern Ontario at Shebandowan, 1127 Km (700 miles) northwest of Sudbury. In 1980 ore production totalled 10.6 x 10 mt (11.7 million tons) from underground and open pit operations. Underground mining methods include blasthole, vertical retreat, sublevel caving, cut-and-fill and undercut-and-fill. Inco reduction operations in the Sudbury area include two concentrators, one smelter, one iron ore recovery plant, a copper refinery a nickel refinery and a high purity plate rolling mill. As well, an electrolytic nickel refinery is located on Lake Erie at Port Colborne, near Niagara Falls. In the Sudbury District, Inco employees total 14,278 of whom 6,490 are directly employed in the mining and milling operations. I T H DRILLING Background - The use of long blastholes in underground operations at Inco mines in the Sudbury district started more than 30 years ago at the Levack Mine. At that time, diamond drills were used to mine ore by open stoping and for pillar recovery. By the 1950's the concept had been extended to all mines. The heavy percussion drill was also developed by this time and led to the acceptance of the 11.43 cm (4% in.) piston diameter drifter for bar and arm and fan drill applications. The use however, of the nominal 5.08 cm (2 in.) diameter blastholes drilled radially from the level or sublevel causes overdrilling at the periphery. As well, the smaller holes are subject to hole deviation, are difficult to drill beyond 38.1 m (125 ft.) and require the need for several drilling horizons or sublevels. The need to improve blasthole stoping techniques and our experience with large diameter blastholes in open pit mining led to the trial of an I T H drill in 1962. The test was unsuccessful however, since button bits were not available at the time and the tungsten carbide cross bit experienced short life, gauge loss, and caused hole deviation and poor penetration rates. The successful application of the raise borer beginning in 1964 and the ability to drill 20.32 cm (8 in.) to 27.94 cm (11 in.) diameter pilot holes led to the development of smaller, more portable, rotary drills for blasthole mining. As a result, a mining method based on the use of 20 cm (7 718 in.) diameter, 60.1 m (200 ft.) long rotary blastholes was developed and tested successfully at our C.C.North Mine. Between 1972, when the method was first tested, and 1973 over 4572 m (15000 ft.) of large holes were drilled with rotary drills in the recovery of 175,960 mt (194000 tons) of primary stoping and pillar remnants. A new mining method was developed that made use of this large hole drilling equipment. Instead of longhole carbide drilling by bar-and-arm or fan drill set-ups at sublevels, the large diameter holes were drilled full stope height from the top sill, which substantially reduced development, drilling time and improved fragmentation. These drills however, were difficult to move and set-up, and had a high maintenance cost and low productivity. The capital outlay and extensive technical development required to improve these drills and reduce the high drilling costs however, was economically unattractive. New development in drills and button bits

Jan 1, 1981

The Palabora ore consists of two types, a carbonatite containing a low titanium magnetite, and a foskorite containing high titanium magnetite. The latter type also contains substantial quantities of phosphate. These two ore types are separately crushed and are kept separate through copper flotation and magnetic separation, for recovery of magnetite, with the low Ti magnetite being shipped as iron ore. High phosphate tailings are pumped to Foskor, a government-owned phosphate plant nearby. The Palabora plant was originally designed in 1966 for 33, 000 tpd using two 54 in. by 74 in. Allis -Chalmers gyratories; two 7 ft (2. 13 m) standards; four 7 ft shortheads; and six grinding lines, each using one 1,200 hp rod mill and two 1,200 hp ball mills. A fifth short- head and one more grinding line were added later; and with flowsheet improvements, the capacity of the plant was increased to 59, 500 stpd. A further plant expansion involving a third 54 in. primary and two 32 ft by 15 ft (9.75 by 4.6 m) 9,000 hp autogenous mills and another flotation section will bring its capacity to 87,500 stpd in 1977. These two fully autogenous mills are constructed entirely out of doors near the primary crusher, and the ground ore will be pumped a mile to the concentrator by a five-stage pumping system. The Palabora ore is mined with 6, 10, and 12 7d (4.6, 7.6, and 9. 2 cu m) shovels and hauled to the crushers in 110 and 165 st trucks. Sixty-five ton trucks were originally used, but the crusher dump pockets were designed for larger units. Dump pockets, crushers, feeders, and take- away belts are offset in order to keep the two ore types separate. Centerlines of the crushers are only 43 ft (13. 1 m) apart; but, because of their being offset, maintenance room is ample. Initially, more carbonatite ore than foskorite was mined; but as the pit has deepened, this ratio has been reversed. The Palabora ore breaks in the pit with a large amount of oversize boulders; and, with the use of larger trucks, a splitter has been installed on one side of each dump pocket to protect the crusher spider. Smaller trucks dump on the opposite side. To accomodate the splitter, the pocket edge has been raised one meter and moved back one meter. Dust is collected through a special vent shaft between the crushers and the mantle relining area; but even so, two high-pressure water spray headers with nozzles are installed under the edge of the pocket at each dumping position. While only one truck dumps at a time, sprays from all four headers are used to suppress dust. Any leakage of water through the seal around the upper bowl of the crusher is caught by a circular trough under the seal and directed to a sump pump. At this point, there

Jan 1, 1978

By John Birkinbine

Through the partiality of my fellow-members I have been able, during seven years' service on the Council of the American Institute of Mining Engineers, to note the development of technical societies, a subject which commends itself as an appropriate theme for me, in retiring from the office of President, at a time when we meet in convention with Canadian technical societies. Our next assembly, called at Chicago at the time fixed for an International Engineering Congress, offers additional reason for the selection of this topic. If subsequent statements appear to give to the American Institute of Mining Engineers greater prominence than to kindred organizations, they may be excused upon the ground of long association with and loyalty to its members, and to a personal knowledge of their work. Besides, data as to its growth and development are more accessible; and at a meeting of the Institute features connected with it may be considered as of greater immediate interest than those affecting other organizations. The purpose of this address is, however, to use the record of the Institute as indicating a similar development of other technical societies, rather than to claim preeminence for any organization; the work of each must speak for it. There is a general tendency to form associations at the present time. Organizations have been created and are active in every profession and in all branches of labor, trade, industry, commerce, manufactures, science and art. A record of such associations and their aggregate membership would be startling, and would show how large a percentage of the population of North America is connected with one or more of them; but the figures cannot be even approximately estimated. The class of associations representing national, state, or local trade interests, such as boards of trade, chambers of commerce, etc., may be used as an illustration. A late report shows that in the

Jan 1, 1893

Flexibility is the keynote in designing modern exploration drills that and mobility. Add to the flexibility of individual drills the wide range of models, and the man looking for a drill has ample choice today. Weight? Choose from models as light as 50 lb or as heavy as 10,000 lb. Hole capacity? From less than 1 in. for smallest core drills to 20 in. or more for auger types. Transportation? The lightest go by packsack (in fact, that is one trade name) ; others are designed to go by Jeep, truck, on skids or are built on light trailers. Power? Select air power, gasoline or diesel engine, electric motor, or use a power take-off from the vehicle on which the drill is mounted. Drill bits offer almost as much variety as the drilling machines themselves. Many drills are suitable for a variety of uses, and often adapt to several types of bits with ease. Some of the types available are: diamond core, diamond reaming, rotary, auger, shot, and special soil sampling tools.

Oct 1, 1955