Search Documents

By S. J. Prison, C. R. Smith

The effect of fluid injection to control water coning in oil and gas wells was investigated. Analytical and model techniques were employed. The factors investigated were the position and length of the completion interval, the point of fluid injection, the viscosity of the injected fluid and the relative thickness of the oil and water sections. The resulting influence of these factors on the net producing water-oil ratio was determined. Several important conclusions can be drawn from the study. In general, it was found that the net producing water-oil ratio can be reduced by fluid injection. The magnitude of this reduction depended on the factors listed above. An important practical consideration is that the injection fluid may be either oil or water. If the injected fluid is less dense than the connate water of the reservoir, the fluid will not be lost. This fact is reassuring when valuable oil is being injected. Efforts to suppress water production were more successful when the injection fluid was more viscous than the reservoir oil, or when a zone of reduced permeability existed in the vicinity of the point of fluid injection. Under test conditions, little benefit was derived through the use of impermeable barriers or cement "pancakes". INTRODUCTION The occurrence of water coning has been known for at least 60 years. In thin oil or gas pay sections, the presence of an oil-water or gas-water contact hinders production and often causes early abandonment of the afflicted well if a completion is even attempted. Even when relatively thick pay sections are found, the encroachment of water when a water drive is present will eventually pose serious water coning problems. This water is often corrosive, expensive to separate from the oil or gas and is costly to dispose of. The theory of water coning has been discussed by a number of authors. 1,2,3,4 Briefly, water coning to the producing interval in a well is due to pressure gradients resulting from the production of fluid from the reservoir. These pressure gradients will cause a water cone to rise toward the bottom of the producing interval if a water-oil or water-gas contact exists. The tendency of the water to cone is offset or partially offset by gravity forces since the water has a higher specific gravity than the oil. A balance then exists between two forces, gravitational forces arising from the difference in specific gravities of the oil and water, and the pressure gradients causing the flow of fluids to the wellbore. If the pressure gradient exceeds the gravitational force, water coning to the wellbore occurs and water production results. Through the years considerable thought has been given to the water coning problem. More than 50 U. S. Patents have been granted to inventors on the subject. A relatively complete literature review of the water coning problem has been made. 5 A number of these patents hold considerable promise for the solution or the partial solution of the water and/or the coning problem. Very little has been written describing field tests of techniques for the suppression of water coning. A notable exception is the paperby West. 6 He reports success in reducing gas coning by a combination of gravel packing and oil injection above the oil-producing interval. He also describes a comparable method to prevent water coning, but provides no field examples. This study experimentally and analytically verifies the benefits of oil injection as a means of partially or completely suppressing the water cone. While the gas coning problem was not treated, it is anticipated that results comparable to those obtained in water suppression could be obtained with reduced oil injection since the viscosity contrast between oil and gas exceeds that between oil and water. For the purpose of this study, the conventional potential flow theory was applied to the water-coning problem. The experimental verification centered on both a radial and a linear model. The model study permitted the investigation of complex flow configurations and the use of fluids of differing densities and viscosities. No analytic expressions are available to permit a solution of the problem as stated (see Fig. 1).

ON July 2 the Krupp plant in Essen was occupied by the French. The City of Frankfurt, on the edge of the Mayence Bridgehead was surrounded by the French. French infantry and cavalry occupied some more towns in the Ruhr. These moves were apparently in the way of reprisals. The Bank of England on July 5 raised its discount rate from three per cent. to four, per, cent., the lower rate having previously prevailed for almost exactly a year.. The advance appears to have been inspired by the reserve ratio, but especially owing to the fact that the low rate in the London market had led to the out-flow of funds from there to other markets. Philip Snowden brought up again in the British .Parliament his motion in favor of the condemnation of the capitalistic system and the substitution of socialism. The motion was put to vote and was defeated by large majority, only the members of the Labor party voting for it. The Allies and the Turks finally came to an agree-ment at Lausanne, the Turks getting about all for which they asked. It would be tiresome to record the details. The main fact is that the Turks, after having been ejected from Europe in 1918, are now going to return. Russia agreed to the settlement respecting the Straits. The Soviet Government of Russia formulated and adopted, subject to ratification, a constitution for the United States of Russia, which appears to be patterned after the constitution of the United States of America and the unwritten constitution of Great Britain. The important thing about this seems to be that it definitely reunites the constituent parts of the old Empire, the semi-independence of the Ukraine being surrendered.

Jan 7, 1923

By PDF

C. 0. FAIRCHILD, Washington, D. C. (written discussion*).-Referring to the paragraph entitled "Effect of change in temperature of absorbing glass on its transmission," Dr. Foote and the writer have been using, since

Jan 11, 1919

By Walter J. Karplus, Otto J. M. Smith

The transient response of earth formations may be tlcter.171ined by means of four electrodes mounted coli-rienrly on n sonde. Exponentially decaying current pules are applied to one pair of electrodes and the re.rrrlting voltage transient at the other pair is recorded. It is shown by theoreticol analysis and verified by laboratory experiments that this arrangement readily yields the direct resistivity of the formation and provides valrrable additional information as well. INTRODUCTION Although electrical transients have been employed with moderate success in geophysical prospecting, their application to well logging has received virtually no attention in technical literature. In the conventional direct resistivity logging methods only the zero frequency impedance of the formation under study is measured, and no information is obtained regarding its reactive characteristics. Since the use of certain transients appears to offer some advantages in this respect, experiments were performed on a laboratory scale to investigate this possibility. This investigation was limited to a study of a four-electrode array where both the receiving and transmitting electrode pairs are mounted on a logging sonde, and decaying exponential pulses are applied to the transmitting electrodes. THEORY Given an electrode configuration as shown in Fig. I, located in a homogenous medium of resistivity p, if each electrode has an effective radius, r, which is small compared to the spacing, s and a, it is easy to show by integrating the volume resistivity that the input resistance, Rrw, of the transmitting electrodes is Rxw=p/2pr If a capacitor of capacity C, charged to a voltage Em, is suddenly connected to these electrodes, the resulting current, I(t), will then be The voltage transient, E(t), at the receiving electrodes may then be found by substracting the resulting potential at electrode Y from that appearing at electrode Z. and by inserting Eqs. 1 and 2 Integrating Eq. 4 with respect to tim

Jan 1, 1957

By Richard D. Hagni

Although the ore microscopist routinely examines polished sections to determine the mineralogy and texture of ores, his importance to the solution of problems peripheral to geology is not always fully realized. The techniques which he uses can be applied with little modification to the solution of a wide variety of beneficiation problem. By extending his studies beyond those normally considered to be of interest to the geologist, he can include examinations of polished sections of selected mill products. This is a logical extension, because the minerals and textures in the polished sections of ores are the same as those in millproducts. The mill dressing engineer should be more aware of the types of beneficiation problem that can be solved by the ore microscopist and what the ore microscopist can do for him. A greater degree of cooperation between the ore microscopist and the mill dressing engineer can be of significant mutual benefit. Ore microscopy holds an advantage over chemical analysis, because the interrelations and combinations ofthe mineral constituents of an ore or mill product can be visually determined. This advantage provides solutions to many beneficiation problem. Locking is a type of beneficiation problem that is particularly amenable to ore microscopy. The percentage, type, and distribution of locked particles can be readily determined with the aid of an ore microscope and an estimate made of the extent of additional grinding required for liberation. The extent of intimately locked types, which no reasonable amount of grinding will liberate, can also be evaluated. Mineral coating conditions, free particles of a deleterious mineral, and free particles of a valuable mineral held in flocculated clusters of gangue are other features that can readily be observed. In some instances, visual examination may show that the problem is not one of locking. Photomicrographs illustrate the variety of beneficiation problems for which the ore microscope is applicable. These problems and their resolution demonstrate the importance of the instrument and show the value of close coordination between the mill dressing engineer and the ore microscopist.

Jan 1, 1979

NEW MEMBERS. The following list comprises the names of those persons who became members during the month of April, 1913: BARNES, BLAKESLEE, Min. Engr Burrwood, La. BOYLSTON, HERBERT M., Cons. Met. Engr 26 Abbot Bldg., Cambridge, Mass. BUEHLER, HENRY A., State Geol Rolla, Mo. CASTO, WILLIAM H., JR., Mining Bonanza, Idaho. COHEN, MAXWELL B., Mill Operator Miami, Ariz. EVANS, MILTON R., Shop Draftsman 92 Division St., Kingston, Pa. HARPER, WALTER S., Asst. Treas 42 Broadway, New York, N. Y. JAMES. JAMES S.. Min. Engr Telluride. Colo.

Jan 5, 1913

By George Mansfield

INTEREST in the reserves of phosphate rock in the United States and their proper conservation has recently been aroused by hearings held in different parts of the country by the "Joint Committee to investigate the adequacy and use of phosphate resources of the United States." This committee was appointed within a few days after a Presidential message to Congress on the same subject, dated May 20, 1938, and began to function almost immediately. Hearings were held in Washington, D. C., Pocatello, Ida., Wilson Dam, Ala., Knoxville, Tenn., and Lake-land, Fla. The resulting testimony, when published, comprised a volume of 1182 pages.1 At the earlier hearings held in Washington and Idaho the seeming disparity between the great reserves of the West and the smaller reserves in the East led to some suggestions as to the desirability of curtailing or even prohibiting the exportation of phosphate rock so that eastern pro-ducers, becoming alarmed, cooperated in making available for the use of the committee information hitherto closely guarded. This informa-tion has provided an opportunity for new studies by official agencies, for a restatement of the reserves of Florida and Tennessee, and for some modification of figures for the Western States. The writer, representing the Federal Geological Survey, was given free access to the Florida material and has prepared for publication a report,2 some features of which are summarized in this paper. The Tennessee material was studied by Dr. G. I. Whitlatch,3 of the Tennessee Division of Geology. Prof. J. Stewart Williams,4 of the Utah State Agricultural College at Logan, has published a recent study of the phosphate resources of Utah and the writer has given some further study to reserves of western phosphate from the viewpoint of including material of lower grade than that hitherto considered.

Jan 1, 1940

By M. C. Fuerstenau, D. N. Collins, R. B. Bhappu, D. N. Moir

D. N. Moir (Senior Scientific Officer, Warren Spring Laboratory, D.S.I.R. Stevenage) and D. N. Collins (Scientific Officer, Warren Spring Laboratory, D.S.I.R., Stevenage, England) — During work on the petroleum sulphonate flotation of beryl in 1959 at Harwell, and subsequently at Warren Spring Laboratory, effects similar to those mentioned by the authors were noticed. Brief details of some of this work were given to the 6th International Mineral Processing Congress at Cannes.' It is interesting to note that the authors experienced strong activation effects with Fe+++ ions on beryl when using petroleum sulphonate collectors. This phenomenon was of interest in our work when

Jan 1, 1963

By Douglas J. Harvey

The surface tension of lead-tellurium alloys (in the range 0 to 6.70 at. pct Te) ad lead-arsenic alloys (in the range 0 to 10.53 at. pct As) has been examined by the maximum bubble pressure method. The surface tension of high purity lead can be expressed over a range of temperatures (M.P. to 750°C) by the relationship = 512 — 0.133t. Arsenic and lellurium were both found to be surface active in lead. The surface excess concentration at 700°C was .found to be constant at 0.74 x 10-10 moles per sq cm for tellurium. The surface excess of arsenic at 700°C varied between 0.26 x 10-10 moles per sq cm at 0.16 at. pct to 1.5 x 10-10 moles per sq cm at 8.3 at. pet. The surface tension of lead has been investigated sporadically over the last 90 years. The first recorded study was made by Quincke1 who used a rather crude application of the drop-weight method. Hogness2 obtained the first reliable value for the surface tension of lead by measuring the pressure necessary to force the liquid metal from the end of a small capillary of known radius. Hogness gives the empirical formula: ?(surface tension)= 444 - 0.077 (l-327) which describes the relationship between surface tension and temperature ("C); This work was followed by that of Bircumshaw3 who applied the two-capillar maximum bubble pressure method of Sugden.4 The values published by Bircumshaw are in good agreement with those found by Hogness. Matuyama5 examined the surface tension of lead by the drop weight method. However, the values found are somewhat higher than those previously reported. More recent investigations by Greenaway6 and by Melford and oar' have resulted in data which are not in close agreement, but which are well within the expected range at most temperature levels. The study of the surface tension of lead alloys began with Drath and sauerwald8 who examined the lead-bismuth system. They found that the surface tension values of the alloys in this system deviated only slightly from the ideal mixture rule. Matuyarna5 examined the lead-antimony system. Bircumshaw the lead-tin, and the lead-indium system was studied by Hoar and Me1ford.10 The results of these investi- gations are summarized in Fig. 1. It may be seen that the data vary only slightly from the ideal mixture rule. As none of the metals studied and reported in the literature has a very interesting effect on the surface tension of lead,*the next logical step might be to examine the effect of metals of low solubility or nonmetals having some liquid solubility. Baes, and Kellogg11 have pointed out that the elements most likely to be surface active in liquid metals are ones of limited solubility in the liquid state and possessing weak intermolecular bonding forces in the solid state. Therefore, Group V, VI and VII nonmetals are most likely to be surface active. It was decided to examine the effect of a borderline metal, arsenic, and a nonmetal tellurium. Arsenic forms a eutectic with lead having a melting point of 290°C and a composition of 6.9 at. pct As.13 Pure arsenic sublimes when heated above 610°C. Even though alloying with lead lowers the vapor pressure, fumes containing arsenic are evolved at a very noticeable rate when lead-arsenic alloys are heated above 650°C. Tellurium raises the liquidus temperature of lead sharply to 904°C,14 the melting point of PbTe (lead-telluride). The solid solubility of tellurium in lead was determined by Greenwood and worner15 to be 0.0007 at. pct at room temperature. EXPERIMENTAL METHOD Surface Tension Measurement—The two capillary maximum bubble pressure method for measuring surface tension developed by Sugden,4 and used later

Jan 1, 1962

By J. Alfred Berger, O. M. Katz

Selected samples of hydrided Zr-Hf alloys were rapidly quenched to voom temperature and exrtrnined metallographically, by X-ray diffraction, and through micro hardness studies to confirm high-temperutuve data Confirming experiments sllowed that there were five phases in this Lernary system: 1) hextrgonal with lattice parameters similar to that of the initia1 Zr-Hf alloy but slightly enlarged due to dissolved hydrogen; 2) fee with properties of a brittle, intermediate, hydride compound; 3) fct with c/a crvoltnd 1.07 and which appeared as a neetilelike precipitale; 4) hexagonal, designated ?, with c/a ratio of 2.37; and 5) orthorhombic, designated X, with a = 4.67, b = 4.49, and c = 5.093 and whose tnicro-st?ruct~ival nppetrl-nnce depcncled o/i, heat lvecrt~r~ent. The tetragonrrl phase never crppeal-erl witkorct the cubic hydricle. Abpecrrtrnce of 0 and A also tlependet on the hafnium content of the zirconium. A previous paper' on the Zr-Hf-H system described the thermochemical data obtained with a high-vacuum, high-sensitivity mirrogravimetric apparatus. This data presented a fairly complete picture of the phase relationships at elevated temperatures. However, it could not establish the actual crystal structures, lattice parameters, or metallographic disposition of the hydride phases. The present complementary study utilizes X-ray powder patterns along with light and electron microscopy to characterize completely the five hydrided phases found in Zr-Hf-H alloys quenched to room temperature. Crystallographic features of the zr-Hf,2,4 zr-H,5-7 and Hf-H8 systems have been summarized in Table I. Designations of a, ß, and ? were retained in the Zr-Hf-H system for the phase regions through which the pressure-composition isotherms always sloped. However, it was not firmly agreed that these were single-phase regions.' In fact, the region designated y always contained a cubic as well as a tetragonal phase after quenching to -196°C. MATERIALS Preparation of the high-purity Zr-Hf alloys has been described.' The four zirconium alloys which were hydrided contained 37 wt pct Hf (23 at. pct), 51 wt pct Hf (37 at. pct), 73 wt pct Hf (58 at. pct), and 91 wt pct Hf (82 at. pct), respectively. These were designated B-2, B-4, B-6, and B-8. Photomicrographs of the initial alloys showed the material to be quite clean as would be expected from the precautions exercised in producing them. However, there were a number of annealing twins but no other subgrain structure. In addition to the four original alloys, fifteen hydrided samples were observed at room temperature. Hydrogen compositions are given at the top of Tables I1 to V. APPARATUS The phases present at elevated temperatures were studied by quenching hydrided samples to room temperature by two different methods, both under vacuum: 1) fast cooling of the sample tubes of the microgravimetric apparatus1'9 with flowing air and 2) rapid quenching into liquid nitrogen. The cooling rate for 1) was 750° to 250°C in 30 sec. Since the microbalance chamber was not designed to permit very rapid cooling of a hydride sample, all liquid-nitrogen quenching was done in an auxiliary experiment. The auxiliary quenching apparatus consisted of a small-bore, high-temperature furnace, a sealed SiO2 tube containing the sample, and a dewar quenching flask filled with liquid nitrogen. The hydrided sample, previously quenched in the microgravimetric reaction chamber, was placed in a platinum boat in a vacuum-degassed SiO2 tube. A zirconium wire getter and degassed SiO2 rod, to reduce the internal volume, were also in the tube. After sealing the tube under vacuum the zirconium getter was heated to absorb the last traces of gas. Only the sample was heated at the reaction temperature for the desired length of time, and then the tube dropped through the opposite end of the furnace into the dewar. A quenching rate of 200" to 400° C per sec was estimated. Analyses of samples after the auxiliary experiment also showed practically no increase in oxygen or nitrogen content from heating in the SiO2 tube. All of the samples were examined at room temperature by the X-ray powder method. The majority of the powder patterns were obtained with double nickel-filtered CuKa radiation after 8- and 16-hr exposures in an 11.48-cm-diam camera. Cobalt and chromium radiation were also used to spread out the high d value end of the Pattern. Such patterns readily identified the minor phases. NO oxide or nitride lines were found. Where sharp back-reflection lines existed it was possible to reduce the

Jan 1, 1965

By A. W. Schlechten

The proposition is advanced that edutcation specifically for exlractive metallurgy is desirable not because the course content is cmique but rather as a means of indoctrinating the student with a backgrocmd that will give him an interest and pride in the profession. Factors that have caused the decline in enrollment in metallurgical engineering courses emphasizing extractive processes are being overcome. There is a need to distinguish between the sciences of metallurgy and the engineering applications to avoid confusion both in and out of the profession. AS a first step in preparing the 1967 EMD Lecture I searched the literature to determine what my predecessors had done hoping thereby to gain some clues for my own performance. The Transactions of the Metallurgical Society show that the first EMD Lec- turer in 1959 was Dr. W. J. Kroll, known chiefly today for his pioneering work on the production of titanium and zirconium, but equally respected by an earlier generation for his contributions to lead refining. He has been followed by a series of well-known and competent metallurgists all possessing specialized knowledge that has served as a basis for their lectures. The EMD Lectures have in general been a review of the development of a certain aspect of the extractive metallurgical industry or a preview of a particular area of science or technology that has applications in extractive metallurgy. The usual format is to describe developments of the past, summarize the present state of knowledge, and make predictions for the future. There has been great variation in the relative amount of time devoted to these three subdivisions, the past, the present, and the future. For example, Professor Gaudin, the 1961 EMD Lecturer, in speaking of Separation Engineering on the Moon, did not have too many examples of past practice and so had to emphasize the future. It is cheering to observe that all of these authorities were optimistic in their predictions. Despite the fact that four of the previous EMD Lecturers have been educators, Professors Gaudin, Pidgeon, Schuhmann, and Kellogg, none of them discussed the subject of education for extractive metallurgists. I might say parenthetically that lecturers in other divisions, such as B. M. Larsen, J. B. Austin, F. D. Richardson, John Chipman, and R. F. Mehl, have commented with concern on the present state of training for extractive metallurgy. What can you say that is new about extractive metallurgy education? Certainly nothing new can be said about the educational process itself. Professional educators do have new approaches to teaching and learn-

Jan 1, 1968

On request of the Commissioner of Education, a small group of administrative professors of engineering and commerce from higher institutions near St. Louis met in conference with the Specialist in Commercial Education of the Bureau of Education on Feb. 22, for the purpose of discussing ways and means whereby the business of our country may be furthered through increased opportunity in our higher institutions for the preparation of engineers with business training. One or more representatives were present at this conference from the University of Minnesota, University of Illinois, Washington -University, University of Missouri, University of Iowa, Iowa State College, University of Kansas. It was recommended at this conference: First, That the Commissioner of Education appoint immediately a committee to consider commercial engineering in its various aspects and to prepare and approve one or more curricula in commercial and industrial engineering that can be recommended by the Bureau of Education for adoption in our colleges and universities. It was suggested that the committee consider the following curricula plans: First, That a minimum number of hours in business training be required in all engineering courses. Second, That a curriculum providing for a minimum of fifteen to thirty units in business economics be incorporated in all engineering courses and offered on an elective basis. Third, That a curriculum in commercial or industrial engineering, permitting full and proper emphasis upon engineering subjects, be offered in the School of Commerce with degree to be given in that school. Fourth, That a five-year combined engineering and commercial course he prepared.

Jan 5, 1919

By Howard N. Eavenson

WHEN the A.I.M.E. was formed 75 years ago the bituminous coal industry was in its swaddling clothes, although it had been operating for more than a century and coal was being mined in every state now producing it, and its output had long passed that of anthracite. In 18/1, the value of bituminous coal was about seventy per cent of the value of all metals produced and more than one fifth of the value of all products of mines, both metallic and nonmetallic.[1a] While many of the operating mines then shipped by rail, most of the development was along waterways, although the canal era of transportation was nearly at its end. Coal mining is a heavy industry and one of the best measures of its progress is its output throughout the period. Fig. 1 shows this graphically from 1800 to 1945. From 1870 to 1910, the production-which is very nearly the consumption-almost doubled every decade, a most amazing growth. In 1918, in World War I, a peak was reached and a decline began, which ended in 1932. A gradual recovery then started, interrupted in 1938 but culminating in the record output of 1944, when, owing to World War II, a tonnage of 619,576,000 was produced. It is evident that the forces leading to the continuous increase ending in 1918 have spent themselves and that only unusual conditions will require so large a production again. The postwar conditions of World War II will probably

Jan 1, 1947

By R. N. Edmondson, L. Mair, M. Tenenbaum

It is the policy of The Metallurgical Society to provide, in the TRANSACTIONS OF THE METALLURGICAL SOCIETY OF AIME, a prompt and accurate medium for publication of reports of significant new research in both the scientific and engineering aspects of metallurgy. Papers submitted to the Society are judged by competent reviewers according to established criteria for technical merit, accuracy, originality, and presentation. STAFF: Editor, Dr. Gerhord Derge; Editorial Assistant, M. A. Redmyrski; Staff Coordinator, James J. Burke. THE METALLURGICAL SOCIETY: W. R. Hibbard, Jr., President; J. C. Kinnear, Jr., Past-President; John Chipmon, Vice President; T. D. Jones, Treosurer; R. W. Shearman, Secretary. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: A. w. Thornton, Chairman; Dennis Carney, John Chipman, J. C. Fulton I. H. Hollomon H. H. Kellogg, A. E. Lee, R. Maddin, J. D. Sullivan, and D. Swan. Review and selection of manuscripts is under the supenision of the following Publications Committees: Extractive Metallurgy Division: T. 0. King Chairman; S. J. Dickenson, R. P. Hermsdorf R. Schuhmann. Jr.. and P. T. Stroup. Institute of Metals Division: Robert Maddin, Chairman F. Lincoln Vogel Jr., Vice-chairman, W. A. Baikofen, R. W. Boliuffi J. H. Bechtold M. B. Beyer. R S. Busk, C. G. Gaetzel, Paul Gordon C. D. Groham, Jr., Robert F. Hehe-mann,' R. I. Joffee, F. c. Joumot Jr lrving R. Kramer A. J. Lena Harold Morglin, C. J. McHargue, Russell A: Meussner, J. B. Newkirk H. W. Paxton, G. E. Pellissier, I. S, Servi, Alon U. Seybolt, A. J. Shaler, and Jack Washburn. Iron and Steel Division: J. C. Fulton, Chairman; T. B King, F. C. Langenberg, W. 0.. Philbrook, and T. 0. Winkler. Published bimonthly by the American Institute of Mining Metallurgical and Petroleum Engineers Inc., 29 West 39th Street, New York 18, N. Y. Telephon: pEnnsvlvanio 6-9220. Subscription 522 Per year for non-AIME members in United States and North South and Central America; $25 foreign;, $5 for AIME members. Single copies, 54.00, single copies foreign, $5.00. The AIME is not responsible for any statement made or opinion expressed In its publications . . . Copyright 1958 by the American lnstltute of Mining Metallurgical and Petroleum Engineers Inc. . . . Registered cable address AIME New York , . . lndexed in Engineering Index Industrial Arts Index and Chemical Abstrats . . . Application for second class mail privileges ii pending at New York, N. Y. Volume 212, Number 4.

Jan 1, 1959

By A. Bar-Or, G. Hirsch, P. Wynblatt

The rates of nucleation and growth at various temperatures in U-0.45, 1.1, and 1.35 at. pet Cr alloys were determined, providing a qliantitative proo-f that the transformation under study is controlled by nucleation and diffusional growth. The linear relationship, log NV US 1/T2, suggests that the nucleation of the alloys is probably controlled by the classical law of nuclei formation. The established linear relationship, log G us 1/T, in the three alloys suggests that growth in each alloy is controlled by bidimensional nuclei formation. It was established that both the rate of growth and the rale of nucleation are retarded by chromium. Using classical formulae, sApN and sApG (the ß/a apparent interphase energies) were calculated from the nucleation and growth results, respectively. It was found that their values are of the same order of magnitude. However, why sApN is unaffected by the addition of chromium, while sApG increases with it, needs further clarification. In the last few years, an appreciable amount of research has been conducted into the mechanism of the ß —a transformation in uranium and uranium alloys. Recently, Burke1 reviewed the published work concerned with this transformation. He concluded that in dilute uranium alloys it is firmly established that, at high temperatures in the a range, ß decomposes by a diffusional process. However, he based his conclusion either on experiments dealing with the over-all transformation,2 or on qualitative results.3 It was felt that a better insight into the mechanism of transformation could be gained from the quantitative measurements of growth and nucleation rates, which we aimed to carry out in the present work. In a previous work,4 we have shown that a rim of a grains is formed during isothermal transformation at the high a range. The thickening of this rim with time was used for measuring the rate of growth in U-0.45 at. pet Cr.5 This method was also used in the present work for two more alloys. For meas- uring the rate of nucleation, a method of quenching and macroetching was developed to allow differentiation between a grains formed during isothermal transformation at the upper a range and those formed after quenching, Fig. 1. EXPERIMENTAL WORK AND RESULTS The Rate of Nucleation. The measurement of the rate of nucleation was effected by counting the num-

Jan 1, 1965

By Sadao Maruyama

INTRODUCTION Since the big discovery of Kuroko deposits in Kosaka mine, Akita Pref., northeastern Japan in 1959, major Japanese mining companies have been engaged in extensive exploration for the deposits expending large amounts of money. Above all their exploration activities have been particularly fruitful in discovering new deposits in northern Akita Pref. It is estimated that the total ore reserves newly found in the area are at least 50 million tons. Kuroko deposits are the most important ore source of copper, lead and zinc in Japan and have been mined since last century in the said area. Kuroko (black ore) is fine, compact aggregates with sphalerite , glena and barite as principal constituents and chalco- pyrite, pyrite and tetrahedrite as subsequent constituents. The name Kuroko comes from its appearance. It is not rare that total grade of copper, lead and zinc reaches 20 - 30% and the gold and silver content is also fairly good. Accordingly the unit value of the ore is much higher than the ore from other types of deposits. Besides the Kuroko ore, the Kuroko deposits consists of Ohko (yellow ore, massive cupriferous pyritic ore), Keikoh (silicious ore, cupriferous network ore) and gypsum ore. This type of deposit is considered to be not only an important source of base metal but also a source of gypsum and barite. Although the importance of this type of deposit had been commonly recognized, sub-surface nature of the occurrence hampered exploration work. In recent years the improved exploration techniques and increased knowledge of the Kuroko deposits have met with remarkable success in the location of new deposits. This outburst of exploration and dis-

Jan 1, 1970

By C. Stansfield Hitchen

The paper describes the application of the logarithmic wedge sector method of quantitative spectrography to the estimation of commonly occurring minor impurities in crude and refined tin. Both arc and spark methods of emission were employed and with the former a new device was used to overcome difficulties arising from the low melting point of the metal. The impurities investigated included antimony, arsenic, bismuth, copper, iron, lead, and zinc, their concentrations lying, in general, between 0.01 and 0.50 per cent. The results obtained show that the method may be usefully employed for the estimation of bismuth, copper, iron, lead, and zinc, in amounts ranging from 0.50 per cent to well below 0.01 per cent. Arsenic and antimony, however, could not be estimated in amounts less than 0.03 and 0.07 per cent respectively. Out of a total of 116 estimations by arc and spark emission, in 96 the errors were less than 5 per cent of the total quantity of the element present, whereas in the remaining twenty, the errors lay between 5 and 25 per cent. Spectro-analytical data for the several impurities studied are given in the form of tables, and curves correlating line-intensity with concentration have also been included. DISCUSSION (R. G. Waltenberg presiding) D. M. Smith, London, England (written discussion).—I am interested in Dr Hitchen's account of his investigations on the application of spectrographic methods to the assay of tin and congratulate him on his valuable contribution to the literature on the subject of quantitative spectrum analysis. Some of the results obtained in the course of investigations carried out for the British Non-Ferrous Metals Research Assn., although obtained under somewhat different experimental conditions, may be of interest in connection with this paper. Arc and spark spectra of standard samples of tin containing various known amounts of antimony, bismuth, cadmium, copper, lead, silver and arsenic have been investi-

Jan 1, 1933

By Robert F. Love

Deep under the hills of southwestern Wyoming lies a nonmetallic mineral deposit of incredible dimensions and value. This nearly pure, horizontal bed of the mineral trona, a sodium sesquicarbonate (Na2HC0,.NaHC08.H20), is found in the Green River formation some 1500 ft below surface. It is believed that evaporation of an ancient saline lake left this sodium carbonate as the evaporite and mysteriously left practically no sodium chloride, which is the common constituent of an evaporated saline lake. The trona bed averages 10 ft in thickness and extends over an area of several hundred square miles. In 1938 a geologist with the U. S. Geological Survey identified the trona in the core from a former oil exploration drillhole. By so doing, he initiated the developments of a chemical industry of impressive growth in the area, an industry on the threshold of further and much more spectacular growth. A drilling program by the Union Pacific Rd. and Intermountain Chemical Co. in the early 1940's succeeded in blocking out mineable reserves of several hundred million tons. Development of the deposit started in 1946 with the sinking of a 12-ft diam, concrete-lined shaft 1500 ft deep-followed by construction of a small pilot calcining plant. Actual mining of the trona started in 1947 and continued on a limited scale until 1953, when the $15 million surface facilities were completed, along with the second shaft and other expanded underground facilities. Since April 1953 the mine has been producing more than half a million tons per year, from which the refining plant has produced more than 300,000 tons per year of high quality soda ash.

Dec 1, 1956

The economic recovery of metals from dilute solutions has been the dream of mining engineers for many years. This subject is now receiving greater attention, particularly for copper, in view of the heightened demand for the metal and the tightening supply situation. A Copper Precipitation session, sponsored jointly by EMD Hydrometallurgy Committee and MBD, which took place during the Annual Meeting in March, heard papers on recent research and plant practice. Although the bulk of research in hydrometallurgy has been carried out in countries other than the United States1, producers in this country are making important contributions to the heap or dump leaching system. They realize that the processes are essentially simple to install and give high recovery rates at reasonable cost. Jacobi estimated in 1963 2 that the copper mining industry obtained a gross return from scavenging operations -on a worldwide basis-on the order of $20 million annually, subject to the usual deductions for refining and realization charges, overheads, taxes, etc.

Jan 6, 1966

By Leo Greenberg

As one of its functions, the U.S. Bureau of Mines gathers and analyzes mine accident data, and then publishes annual reports on work injury experience in the various segments of the minerals industry- coal, nonmetals, rock. These reports contain a wealth of detailed data, with a multitude of analyses and cross-tabulations, all intended to shed as much light as possible on accidents and to suggest possible ways of reducing them. In this article, the terms, "injury" and "accident" will at times be used interchangeably to denote accidents which cause disabling injury. The Bureau bases many of its analyses on American National Standard Z16.1 for recording and measuring work injury data. This document establishes two models for measuring disabling injury experience: (1) the frequency rate, obtained by dividing the number of man hours into the number of injuries multiplied by 1 million, and (2) the severity rate, similarly constructed, with the variable of interest being the number of days lost due to these injuries. Similar computations are performed by the U.S. Bureau of Labor Statistics and the National Safety Council. Additionally, these models are used in many other countries, sometimes with minor changes.

Jan 1, 1971