Search Documents

By Reger, B. David

FOR many years, the belief that the so-called "Clinton" sand of Ohio might produce. oil and gas, if it could be reached, has been prevalent in West Virginia. To test this theory, many hundreds of thousands of dollars have been spent and several extremely deep wells, including the deepest boring of the world, have been sunk at various points. With the exception of one well now completed through the sand and the possible exception of another still in progress, all of these wells failed to reach the goal, either through failure of funds or through drilling accidents. REVIEW OF DEEP DRILLING The subject of deep-sand oil and gas in West Virginia has already been discussed by the author1 and by White.2 In these papers, it was shown that the Upper and. Middle Devonian shales, lying between the Berea oil sand (basal Mississippian) and the Oriskany sandstone (Lower Devonian), thicken steadily from eastern Ohio across northern West Virginia and Pennsylvania; but it was stated that the same rate of thickening did not occur in that part of West Virginia south of the Great Kanawha River and in the adjoining portion of Kentucky. In spite of this great eastward thickening, the fact that both the Oriskany and "Clinton" sands, the latter of which is equivalent to the White Medina of New York, exist in great thickness all along the Appalachian Mountains farther east, was held as proof of their probable presence in the deep Appalachian basin.

Jan 3, 1925

By K. E. Gray, G. M. Myers

In previous publications,5 results of single-blow bit tooth impacts on saturated rocks at various stress states were reported. This paper extends these earlier works to include study of bit impact tests on salt water-saturated Berea and Bandera sandstone samples under conditions of elevated confining and pore pressure. During the tests dynamic filtration and deposition of a mud cake were occurring due to the presence of drilling mud in the borehole and a borebole-to-formation pressure differential. Results indicate that saturation of these sandstones with salt water tends to make them weaker than when saturated with nonreactive fluids. Plastic failure often occurs even when extremely high fluid-loss muds are present in the borehole. The failure mode tends toward plasticity with decreasing fluid loss. Brittle failure of sandstones in mud-filled holes is apparently relatively rare. Depending on the stress level, and the associated failure mode, withdrawal of the bit tooth induces a tensile force that seems rather important relative to the quantity of rock removed by vertical tooth impact. INTRODUCTION A vast majority of the oil wells drilled today involve the use of colloidal muds having a measurable mud filtrate loss. It is known from field experience that reduction of the water loss of a mud generally results in a reduction of the penetration rate. This paper describes an investigation of crater formation at simulated bottom-hole pressure conditions for drilling fluids having different water losses. The literature on single bit tooth impact (cratering) at atmospheric conditions is extensive, but only a limited amount of work has been performed at the stress conditions similar to that found in oil wells. Spherical penetrator cratering tests on rocks at hydrostatic pressure were performed by Payne and Chippenda1e.1 Chisel impact studies on limestone with independently varying overburden and borehole pressure and atmospheric pore pressure were reported by Garner, et al.2 Gnirk and Cheatham3 performed "static" penetrator tests on dry rocks at equal overburden and borehole pressures. Podio and Gray4 studied the effect of pore fluid viscosity at atmospheric pore and borehole pressures and varying overburden pressures. Their results illustrated the importance of fluid saturation of the rock. Yang and Gray5 reported single tooth impact tests on saturated rocks at elevated borehole, pore and confining pressures, but with equal pore and borehole pressures. For the work reported in Refs. 4 and 5, filtration across the hole bottom purposely was avoided. Maurer6 has investigated the effect of independently varying pore and borehole pressures at elevated overburden pressures by using a zero water-loss mud in the borehole. His tests were carried out under conditions that allowed independent control of overburden, pore and borehole pressures, but without control of filtration at the hole bottom. EXPERIMENTAL APPARATUS AND PROCEDURE APPARATUS The single blow chisel impact apparatus used by Garner,2 as modified for this study, is shown in Fig. 1. A cross section of the pressure vessel is shown in Fig. 2. Several pieces of auxiliary equipment were added to the original apparatus in order that the borehole and pore pressure could be applied in a manner analogous to the actual bottom-hole situation. The pore-pressure system included a filtrate volume-measuring transducer and had sufficient surge capacity to allow filtrate to be injected into the sample without significant changes in pore pressure at points remote to the borehole. The borehole-pressure system contained a cross connection to the pore-pressure system so that both systems could be pressured simultaneously. The borehole-pore pressure differential was applied rapidly by the use of a quick and full-opening valve. The operation of this valve triggered two industrial

Jan 1, 1969

As already announced in the notice of the 114th (New York) Meeting of the Institute, the ladies present met and organized the Women's Auxiliary of the Institute. All ladies of the families of members of the Institute-are eligible to this Auxiliary. The purpose and objects of the Auxiliary are well stated in the address of the President, Mrs. S. J. Jennings, in opening the organization meeting on the morning of Feb. 20, 1917. The address follows: "Ladies: Friends from far and near, on behalf of the Women's Entertainment Committee of the A. I. M. E., I extend to you a hearty welcome. "Most especially are we glad to see our friends from the Pacific Coast and the middle West, .whose royal hospitality to the members of the A. I. M. E. and their wives and daughters on their trips to California and to the Copper Country of the Southwest can never be forgotten. We are glad to be able in some small measure to return it.

Jan 4, 1917

By John Birkinbine

The early history of the mining and metallurgical industries of Pennsylvania is so intimately associated with the section of the State in which we meet, that a brief resume of a few of the important historical facts, and a reference to some of the more modern enterprises, in which members of the Institute have been largely concerned, seem appropriate to this occasion. It is just two hundred years since the publication of the earliest mention of the manufacture of iron in Pennsylvania. What kind of iron this was, or where or by whom it was produced, is uncertain. The only record of it is the following verse, quoted in the admirable work of Mr. James M. Swank,* from a poem published in 1692: " A certain place here is, where some begun To try some Mettle, and have made it run, Wherein was Iron absolutely found, At once was known about some Forty Pound." One who stood one hundred and seventy years ago on the summit of this Neversink Mountain † (had the atmospheric conditions been favorable, and the timber somewhat removed) might have noticed in the daytime the smoke, or at night the reflection, from the fires of the first successful Pennsylvania iron enterprises, scarcely 15 miles to the south, viz.: Rutter's bloomary forge, built in 1716, and the Colebrookdale blast-furnace erected in 1720, respectively 3 and 8 miles distant from Pottstown. Here the pioneers of iron production in the State which has so long led, and still leads all others in this manufacture, had their trials and successes ; and it may be a satisfaction to some who bewail a present depression in trade, and the low prices now ruling, to recall the fact that in 1731 pig-iron is reported to have been sold ''in large quantities" at the Colebrook-

Jan 1, 1893

By D. Swan

Industrial research may be defined as a critical and exhaustive investigation to create new and better ways of doing things. The results of industrial research are new and improved products, processes, and techniques. This broad definition, of course, covers investigation of all subjects by either individuals or groups of people, and this chapter aims to examine the purpose (what research tries to do), and methods (or how research is done) as applied in the mineral industries. Concepts and History The idea or concept of organized research probably originated in the universities of Europe. There, groups of scholars banded together for discussion and application of their particular specialty to a common problem. Publication of the conclusions drawn from such investigations gave scholars in other areas the opportunity to review and criticize the work of their colleagues, and one of the hallmarks of scientific research work is the publication and criticism of the results of the investigation. It was not until the late nineteenth century that the concept of organized research for the profit of industry was recognized. During the late nineteenth and early twentieth centuries, a large number of industrial enterprises sponsored organizations to study the application of the physical sciences with the aim of making discoveries that would result in profit to the sponsoring organization. The tangible benefits accruing from these activities were so great that they, in turn, fostered several other methods for the support of organized research activities. For the large problems involving public interest, United States Government scientific research laboratories were set up. As the demand of smaller enterprises for research activities increased, research institutes and consulting laboratories were organized. In Europe the idea of common industry sponsorship of research centers grew and many large research organizations there were sponsored by associations of manufacturers. Finally, in the United States

Jan 1, 1964

By R. B. Ladoo, C. A. Stokes, R. N. Secord, A. L. Hall

INDUSTRIAL mineral history shows that the entrance of new, nonmetallic minerals into commercial production can be expected to occur from time to time. Latest entrant into the field is wollastonite. Except for one short-lived period in Kern County, Calif., starting in 1933, wollastonite has never before been produced on a commercial scale. But the signs are up for its entrance as an economic factor in the mineral market. Small scale experimental production from a deposit near Willsboro, N. Y., started about 1943. A pilot plant was built in 1949-50 and irregular, small scale, production has continued. In early 1951 Godfrey L. Cabot, Inc. of Boston, world's largest producer of carbon black, took an operational lease on the property to study the deposits and make market surveys. This became Cabot's first venture in the mineral field, when they took over operations and began design of a new mill, expected in production in 1953. Properties The properties and major uses of wollastonite are comparable to New York fibrous talc. It has about the same specific gravity and index of refraction as talc, but is somewhat whiter and softer. The two most important fields of use, paint and ceramics, are the same as for talc. Ground wollastonite has a fiber length as much as 13 to 15 times the diameter. This particular property makes it applicable in the paint field and others. In addition, the length-diameter ratio may be controlled to rather narrow limits by choice of grinding method. Another important commercial property is brightness or whiteness. Wollastonite reads from 92 to 96 pct of MgO on the G.E. brightness meter for a 99 pct -325 mesh grind. Purity and uniformity of product are important. Chemically, the wollastonite now being mined analyzes SiO2 51.76, CaO 47.56, FeO 0.46, MnO 0.04, and H2O 0.09 pct. Theoretically pure wollastonite analyzes SiO2 51.75 and CaO 48.25 pct. This analysis indicates over 98 pct calcium silicate, with only small amounts of contaminating ingredients. That these ingredients are not detrimental to color or brightness is shown by the high brightness value of the fine ground material. [ ] By-product calcium silicate from electric furnace production of phosphoric acid has little physical re-semblance. to this wollastonite, being an off color white, and lacking in fibrous crystalline character. Minerology Wollastonite is a calcium metasilicate, CaSiO3, a white, medium hard, fibrous mineral. In this deposit wollastonite occurs as well crystallized aggregates of bladed crystals intergrown with garnet, and with a few percent of green diopside. The beneficiated product is about 75 pct wollastonite, 15 pct garnet, and 10 pct waste, largely middling. Wollastonite-garnet ore occurs in at least two beds. The main bed, varying in true thickness from 30 to 70 ft, dips into the hill at an average 30° and is enclosed in gneisses. Diamond drilling has proven the orebody to an average depth of 200 ft along 2000 ft of outcrop with adequate tonnage for many years of quarry operation. The wollastonite-garnet ratio varies locally, but average composition is uniform over long distances. A friable ore, it is easy to drill, shoot, and crush. Beneficiation Unlike talc this ore has to be beneficiated. Successful treatment depends upon the fact that it contains virtually nothing but wollastonite, garnet and a minor percentage of diopside. A very pure wollastonite product can be made by high intensity magnetic and/or gravity separation methods.

Jan 1, 1952

By A. M. Gaudin

Activation of sphalerite with silver ions results from the exchange of two Ag ions for one Zn ion in the sphalerite lattice. The exchange is proportional to the logarithm of time and proceeds until either of the reactants is consumed. Sodium cyanide prevents the activation of sphalerite by controlling the ratio [Zn++]/[Ag+]' in solution. If sphalerite has already been activated with excess silver, cyanide ions can deactivate sphalerite provided oxygen is present. SOLUBLE: silver salts are effective activators for flotation of sphalerite with potassium ethyl xan-thate as collector.* Since sphalerite takes up large quantities of silver ions rapidly,2-4 investigation of this system appeared fruitful for studying the mechanism of sphalerite activation and deactivation. Experimental data presented here comprise studies of the mechanism and rates of activation and deactivation of sphalerite with silver and cyanide ions. A 20-lb sample of sphalerite from Ottawa County, Oklahoma, was handpicked, crushed, screened, hy-drosized to produce a 65/100-mesh fraction, and purified by electrostatic separation. The sphalerite was then leached with benzene and absolute ethyl alcohol to remove possible organic contaminants and with 0.1 M NaCN to remove any copper that might have been picked up during screening. The benzene had been specially purified by grinding with fine sphalerite for 12 hr to remove trace impurities that might have had a specific affinity for sphalerite. Ii'inally, the mineral was washed, dried in flowing nitrogen, and stored in large ground-glass stoppered weighing bottles under a small nitrogen pressure. The specific surface of two samples from the 65/100-mesh sphalerite stock, measured by krypton gas adsorption," was 420 cm2 per g. Compared with spheres of the same size and specific gravity, the prepared mineral had five times as much surface. Results of a wet chemical analysis and of a spectro-graphic study are given in Table I. Manganese, nickel, tin, indium, thallium, cobalt, and magnesium were not detected spectrographically. All solutions were preparid by -adding reagent-grade chemicals to conductivitv water. which had been previously saturated with the desired gases. Nitrogen and oxygen were purified, but no attempt was made to purify the laboratory air. Radioanalysis was carried out with prepurified Ag110 tracer obtained from the Oak Ridge National Laboratory. The complete decay scheme for Ae is complex. Its primary emissions are 0.09 and 0.55 mev ß rays and 1.48 mev y raysB and its half-life is believed to be 270 days. In preparation of solutions of AgNO3, the amount of Ag110 added was negligible compared to that of the inert silver. Abstraction of silver from solution by sphalerite was measured after agitation of 1.5 g sphalerite with 20 ml of solution in 50-ml pyrex flasks. All sample preparations were carried out in a dry box so that the proper atmosphere could be maintained. After the mineral had been agitated in the silver nitrate solution, an aliquot of the solution and a sample of the wet mineral were transferred to separate counting vials and weighed. The solid sample was dried and re-weighed and the activity in both vials measured by means of a scintillation counter. With scintillation counting it is possible to count y radiation from the solid and liquid, a distinct advantage over the older ß-ray counting techdiques.4 All measurements of silver activity were made using a sodium-iodide well-type scintillation counter. The amount of zinc in solution was measured colorimet-rically by the monocolor method of Sandell.7 Activation Studies Exchange Between Zinc Ions and Silver Ions During Activation: The increase of Zn++ in solution during activation with Ag+ is shown in Table 11. These data indicate a replacement of one Zn++ by two Ag+. Analysis of a separate two-month agitation test indicated that the replacement of Zn++ by Ag+ was, as expected, in the molar ratio of 2.0.

Jan 1, 1958

By R. A. Deju, R. B. Bhappu

The basic structural unit of all silicate minerals is a tetrahedron with a silicon atom at the center and four oxygen atoms at the corners. The oxygen-silicon distance is about 1.6 & and the oxygen-oxygen distance about 2.6 &. The different types of oxygen-silicon frameworks in the various silicates are based entirely on the combinations of the tetra-hedral oxygen-silicon groups through sharing of oxygen atoms. In recent years, infrared spectroscopy has permitted estimation of the ratio of the ionic character of the oxygen-silicon bond to be a few times that of the oxygen-carbon bond and the ratio of electro-negativity of the two bonds has also substantiated this finding. On this basis, it is generally accepted that the oxygen-silicon bond is the strongest one occurring in silicate minerals. As the oxygen-silicon ratio increases from quartz to the olivines, a greater percentage of the oxygen bonding power is available for bonding to cations other than silicon. Hence, with an increasing oxygen-silicon ratio, there is increasing oxygen-to-metal bonding. Upon the fracturing of a silicate mineral crystal, the oxygen-metal bond, which is almost entirely ionic in character, should break more easily than the stronger oxygen-silicon bond, resulting in a greater number of unsatisfied negative forces on the surface. If, then the mineral is immersed in a liquid containing hydrogen ions, these negative forces should tend to be neutralized by hydrogen ions from solution, resulting in a change of the pH of the solution. An increase in the degree of adsorption of hydrogen ions is to be expected as the oxygen-silicon ratio in the crystal structure increases. This study attempted to correlate the oxygen-silicon ratio for various representative silicate minerals to the adsorption of hydrogen ions. Experiments to determine the effect of surface area on this adsorption and to investigate the effect of surface iron were also conducted. It is believed that such studies of the surface properties of silicate minerals will supply pertinent information about their behavior in froth flotation systems. EXPERIMENTAL PROCEDURE Ion Exchange: Carefully selected, hand-picked samples of the minerals investigated were dry-crushed in a ceramic ball mill and sieved to obtain a minus 100 plus 200-mesh sample. The sized samples were then run through the electro-magnetic separator to remove any iron-bearing particles. A 10-g sample of each mineral was placed in 100 ml of freshly deionized water previously adjusted to a pH of 3.50 with HCl. The beaker containing the sample and the water was placed under a bell jar from which the air was displaced at once by nitrogen gas from a tank. All experiments were carried out in a nitrogen atmosphere. The sample and solution were stirred gently but continuously during the entire experiment, the stirring speed being kept about the same for all runs. Changes in pH were followed with a Beckman Zeromatic pH meter and recorded on a

Jan 1, 1967

By Dwain K. Butler

INTRODUCTION Characterization of a site for the prediction and simulation of dynamic events requires the determination of mechanical properties of the rock at stress/strain levels and rates and at a scale appropriate for the events and critical structures involved. The structures of interest can be on the surface, underground, or designed to impact and penetrate into the site (projectiles). Dynamic events of interest are equally diverse: seismic waves from distance earthquakes or explosions; close-in phenomena associated with earthquakes and explosions; vibrations associated with heavy equipment or machinery; and stress transients associated with impact and penetration. The complexity of site characterization depends on two factors not specifically related to the nature of the site itself: the stress levels generated by the dynamic event and the sophistication of the prediction and simulation techniques. For very high stress levels, such as occur near a nuclear detonation, and for low stress levels, such as occur during seismic wave propagation, site characterization is simplified, and often certain details of the site are not particularly important, such as shear strength variations in the case of very high stress levels. In the intermediate stress range, however, all descriptive relations are non- linear, a complete finite strain constitutive model is required, and all details of the site, such as lithology and fracture distribution, become important. The site characterization must be complete enough to support the most sophisticated prediction and simulation technique that will be applied to the analysis of the dynamic event. The procedures of site characterization are illustrated in this paper by a specific dynamic event, projectile impact and penetration, and a specific site, an outcrop of Dakota Sandstone near San Ysidro, New Mexico. The structure of interest was the projectile itself: nominally, 1.5 m in length, 0.165 m in diameter, 180 kg

Jan 1, 1984

By Gerd L. Klinkenborg

Ever see a curvaceous conveyor belt? Reports from Europe indicate appreciable interest in a relatively new system that has revamped some of the concepts of what single-belt conveyors can and cannot do. Invented about ten years ago by two German engineers, the so-called "Serpentix" single-belt conveyor, patented by the firm of Albert Stuebbe, is now operating at more than 100 foreign installations. The system boasts of three unique capabilities-climbing, turning and side discharge of load-which give it, the advantages of a multiple-unit system. The new conveyor needs only one drive station (which may be combined with tensioning), and except for the immediate area of the drive, is capable of conveying loads over a non-linear route. Transfer points are eliminated, and discharge points, which may be located anywhere along the route, may be operated automatically or manually, by direct or remote control.

Jan 1, 1962

Inflation, fuel shortages, environmental restrictions, and a worldwide recession that sharply curtailed the demand for goods and services, were the main causes for the poor performance & virtually all industrial minerals in 1975. This poor showing was not a surprise. As Felix Shay correctly predicted in his introductory remarks to last year's industrial Minerals Review (ME, Feb. 1975, p. 70), ". . . the minerals industry will soon be facing falling demand as a consequence of sharp declines in auto production, housing, appliances, and other consumer goods. Moreover, when sales weaken. the high-volume, low-priced industrial minerals will incur sharply.

Jan 3, 1976

By L. D. Fetterolf, G. T. Mahler, W. M. Peirce, R. K. Waring

UNTIL recently, the only commercial method of producing magnesium has been fused salt electrolysis, despite a considerable amount of experimental work on the direct reduction of magnesium oxide. In this early work, a number of investigators demonstrated that magnesium oxide would react with any one of several reducing agents to produce magnesium vapor, but that the mixture of magnesium oxide and reducing agent must be heated to a high temperature even in a vacuum. In particular, it was demonstrated that silicon and aluminum are effective reducing agents and that when either of these is used the magnesium vapor can be condensed to massive metal. In spite of this knowledge, no successful commercial reduction process was developed, at least in this country, because of the operational difficulties imposed by the requirement of high temperature and vacuum and because of the high cost of the reducing agent. The outstanding experimental work done by Pidgeon, who carefully reviewed all of the known methods of making magnesium and then selected ferrosilicon reduction, overcame some of the operational difficulties. The process developed by Pidgeon comprises briquetting a mixture of calcined dolomite and reducing agent, pre-heating the briquets to about 600°C. in an externally heated alloy retort, reducing the MgO with silicon in an evacuated horizontal alloy retort heated externally to about 1150°C., and condensing the magnesium vapor to a solid in a cold extension of the retort projecting beyond the fr6nt of the furnace. A major advantage of Pidgeon's process is that the retort is not cooled down between charges. Earlier investigators had used apparatus that necessitated cooling and reheating of the retort between charges. Early in January 1942, when the War Production Board was considering the Pidgeon process for quickly increasing the production of magnesium, The New Jersey Zinc Co. offered to have a research investigation of the process carried on, with the hope of assisting in its further development. This offer was accepted, and a two-retort pilot plant was built at Palmerton and put in operation on Jan. 29, 1942. An intensive investigation of certain phases of the process was carried out in the ensuing four months. This investigation was completed in the last part of May 1942, and the pilot plant was then shut down. Subsequently, The New Jersey Zinc Co. was requested to have further development work done on the process, and a more extensive investigation was undertaken in August I942 under contract with the War production Board and under the super- vision of the War Metallurgy Committee. This paper describes the phases of the investigation that are thought to .be

Jan 1, 1944

By Alfred Weiss

Daniel C. Jackling's innovative concept for handling low grade ores ushered in a new philosophy of open pit mining. As one of the greatest minemakers of all times he revolutionized major segments of the industry and helped strengthen US defense efforts during World Wars I and II by making possible the tremendous copper supplies from US mines. Many great mining men have since followed in his footsteps with their discoveries of new orebodies or development of new mines. Their brilliance in leadership can also be traced to the coupling of a new idea to the physical nature of the materials in the earth's crust or to the extractive stages of minerals recovery. The minerals industry is now in another era of change and must again devise techniques to meet the challenge. The task is not only to create new exploration techniques and develop new mining methods, but, I believe, to optimally apply new concepts and tools in daily decision-making.

Jan 11, 1978

By Elmars Ence, Harold Margolin

The Ti-Fe and Ti-Fe-0 systems were re-examined because of the controversy regarding the existence of Ti2Fe, and to consider all available data points to the existence of Ti,Fe. The Ti-Fe-0 system contains two ternary compounds: E, corresponding to Ti2Fe; and y. SEVERAL authors have investigated the constitution of titanium-rich alloys of the Ti-Fe system. The most extensive study of titanium-rich portions of the Ti-Fe system was by Van Thyne, Kessler, and Hansen,' who investigated this system up to 50 pet Fe and used the highest purity materials available for their alloy preparation (iodide titanium was used for alloys up to 20 pet Fe). According to Van Thyne et al., phase relationships in the region of investigation are governed by phases a,ß, and TiFe. No evidence of an intermetallic compound Ti,Fe was found. although earlier. works by Laves and Wallbaum,' and Duwez and Taylor' reported its existence. Rostoker's study on the occurrence of TilX phases" confirmed the findings of Van Thyne et al. Rostoker proposed that the compound Ti Fe found by Duwez does not exist but is actually a ternary compound, Ti1Fe3O, originated by inadvertent oxygen contamination. The partial isothermal section of the ternary Ti-Fe-0 system as reported by Rostoker' seems to confirm this explanation. In the course of phase diagram work conducted at New York University, however, certain irregularities were observed to be associated with ternary systems of the type Ti-Fe-X. The ternary phase 6, observed in the systems Ti-Fe-Mo' and Ti-Fe-V." was found to be structurally identical to the com-pound Ti2Fe as reported by Duwez and Taylor, and to Rostoker's compound Ti1,Fe2O. Since the amount of oxygen possibly present in the Ti-Fe-Mo and Ti-Fe-V systems could not account for the observed amounts of the compound, it appears that the d phase in these systems is not Ti,Fe,O. On the other hand, considering the amounts of the 6 phase, particularly in the Ti-Fe-Mo system, the location of the phase was uncertain. It was felt that the introduction of the Ti2Fe phase would alleviate some of the inconsistencies of the two systems. Because of the uncertainties relating to the phase Ti2Fe, or Ti1Fe2O, it appeared worthwhile to re-examine the Ti-Fe and Ti-Fe-O systems in the vicinity of these compounds with highly sensitive metallographic techniques and with X-ray methods. Experimental Procedure Alloy Preparation—For the study of the binary system four alloys were prepared, containing 26.9 (30 wt pct), 34.0 (37.5 wt pet), 41.2 (45 wt pet), and 56.3 (60 wt pet) atomic pet Fe, and for the ternary Ti-Fe-O system 18 alloys were prepared in the composition range of 1.6 to 16.9 atomic pet 0 and 24.3 to 55.7 atomic pet Fe. The materials used for the Ti-Fe alloys were iodide titanium (99.98 pet Ti, 0.002 pet 0) and Ferro-vac-E iron (99.95 pet Fe, 0.0052 to 0.0072 pet 0). For the Ti-Fe-O study the materials used were sponge titanium containing less than 0.06 pet 0, Ferrovnc-E iron, and Baker's analyzed TiO2. The nominal weight and atomic percentages of the ternary alloys prepared are shown in Table I. Melting—Charges of 10 to 15 g were melted in a nonconsumable arc furnace in argon atmosphere according to the technique described elsewhere.'" Since there was practically no weight loss through the various stages of melting and oxygen losses have not been observed previously, it appeared justifiable to use nominal composition for interpretation of data. Iodide titanium control buttons, of the same mass as the Ti-Fe charges, and melted under the same conditions, were used to check hardness pickup during melting. A hardness increase of 2 to 3 Vhn was found. Heat Treatment—The specimens were annealed in quartz capsules under argon. To avoid contact between the specimen and capsule material all specimens were wrapped in titanium sheet. The annealing times are given in Table 11. The attain-

Jan 1, 1957

By R. G. Knickerbocker

A most important research and development item on ferroalloys in the calendar year of 1949 was the increase of interest in the recovery of secondary manganese. Owing to the importance of manganese to the nation's welfare, it is Ferroalloys most necessary that all possible avenues of research and development on the recovery of this vital metal be investigated. The principal objective of this new development is to recover manganese from steel furnace slags. Steel furnace slags contain a total of approximately 772,000 tons of metallic manganese which is compared to the 680,000 tons of metallic manganese as ferromanganese that is estimated to be used by the steel industry, annually, at this time.

Jan 6, 1950

By W. H. W. Husband

Rock salt has been solution mined for many years in many countries. Attempts have been made in the past in Canada and various other countries to produce potash by the same method. However, only Kalium Chemicals Ltd. has been successful, possibly because the conditions in Saskatchewan are the most favorable to be found so far for the development of a solution-mining method for potash. In view of the fact that few studies of solution mining of potash have been attempted, only one company has succeeded in using the method, and no information has been released by this company, the application of solution mining of potash ore bodies has to be presented on the basis of available theory, past small-scale studies, and recent patents. A simple mining method is outlined and possible methods of recovering the potash from the brine are discussed. Dissolution data pertaining to solution mining of potash, flowsheets, and material balances are presented. The available information is brought together in a cost analysis to show capital and product costs in terms of 1966 dollars.

Jan 1, 1972

By M. S. Burton, H. H. Kranzlein, G. V. Smith

The influence of up to 2 at. pct of Ni and Pt on the yield strength of mono- and polycrystalline high-purity iron has been evaluated at temperatures from + 25° to -196°C. Current theories of solid -solution strengthening fail to explain the experimental observations. The temperature dependence of yield stress was found to be less in the alloys than that in high-purity iron. The room-temperature yield stress increased with alloy content, but at —78°C the yield strength first decreased with increasing a1loy content. AS a result of many studies, a number of theories have been proposed for solid-solution strengthening. The purpose of the present study was to evaluate these theories, as applied to the solid-solution strengthening observed in Fe-Ni and Fe-Pt alloys. Of various theories of solid-solution strengthening, those of Cottrell,1,2 Fisher,3 Suzuki,4 and Mott and Nabarro5 are most prominent, and have been discussed widely in the literature.'-' Of the recent concepts of solid-solution hardening the work of Fleischer9 is notable. Each of these models has been applied to particular alloy systems with some success, but in general none has proved generally applicable. In many of the previous studies to assess the effects of alloy additions in ferrous systems, lack of adequate control of the purity and grain size of the materials has obscured strengthening effects, so that few comprehensive data relating composition, temperature, and change of lattice parameter have been determined. In the present investigation an attempt was made to obtain data which would be meaningful in evaluating the theories of strengthening. Materials of high purity were used to minimize extraneous impurity effects, and both single crystals and polycrystalline materials were studied to evaluate the effect of grain boundaries. Nickel and platinum were chosen as alloy additions, because both belong to the same chemical group and have the same crystal structure and valence, with markedly different atomic diameters. It appeared that some conclusions regarding atomic size effect on strengthening might be made. MATERIALS AND PROCEDURES Fe-Ni and Fe-Pt alloys containing 0.5, 1.0, 1.5, and 2.0 at. pct alloy additions were prepared from high-purity materials. The iron was supplied by the American Iron and Steel Institute from a stock of 99.98 pct zone-refined iron prepared by Battelle Memorial Institute. The minimum purity of the nickel and platinum used for alloying was 99.98 and 99.999 pct, respectively. Alloys were prepared by levitation melting, cast into cylindrical copper molds, and cooled, all under a partial pressure (0.3 atm) of purified helium. Samples were 0.375 in. in diameter and weighed 20 to 25 g. Chemical analyses of the alloys are given in Table I. A sample of unalloyed iron also was cast as a control specimen.

Jan 1, 1965

By P. Gordon

An isothermal jacket microcalorimeter, supplemented by metallographic, microhardness, and X-ray measurements has been used to study the isothermal annealing of high purity copper after room temperature tensile deformation. The amount of stored energy released during annealing has been measured as a function of deformation in the range 10.8 to 39.5 pct elongation. The data have shown the major heat effect to be associated with recrystallization and have allowed an analysis of the recrystal-lization kinetics and the calculation of activation energies of recrystallization. WHEN a metal is deformed plastically, some of the energy expended is dissipated as heat during the working process, while the remainder is stored within the metal in the form of lattice distortions and imperfections. During subsequent heating of the metal, the distortions and imperfections can be largely annealed out and the associated stored energy released as heat. It is apparent that measurements of the evolution of stored energy during such annealing may produce important information concerning the nature of the annealing mechanisms and the imperfections involved. Some excellent studies of this type have been made in the past, notably those of Taylor and Quinney,' Suzuki,2 Bever and Ticknor,3 Borelius, Berglund, and Sjöberg,4 and Clarebrough et al.5,6 None of this work, however, employed isothermal techniques, with the exception of the Borelius studies' in which only the early annealing stages were investigated. Since isothermal measurements, as compared with heating or cooling curve, have the merits that 1—they reveal the kinetics of a process more clearly, 2—the results obtained are more easily applied to theory, and 3—most fundamental investigations of annealing using techniques other than calorimetry have been carried out isothermally, it was considered important to apply calorimetry to the study of the isothermal annealing of metals. Accordingly, an isothermal jacket calorimeter of the Borelius type,' supplemented by metallographic, hardness, and X-ray measurements, has been used to study the annealing of high purity copper after room temperature tensile deformation. Experimental The microcalorimeter has been described fully elsewhere." Briefly, the specimen to be studied is placed in a constant temperature environment of virtually infinite heat capacity achieved, as shown in the drawing of Fig. 1, by means of a vapor thermostat. A high thermal resistance is provided between the sample and the environment and a sensitive differential thermopile (see Figs. 2 and 3) arranged with half its junctions in contact with, and thus at the constant temperature of, the environment, and the other half in contact with the sample. A reaction in the sample develops a small difference in temperature, AT, across the thermopile, which is followed by a recorder-galvanometer set-up as a function of time, t, and is converted to reaction heat per unit time, P, by the use of the equation AT P=a?T + b AT dt The constants, a and b, in Eq. 1 are determined by a simple calibration, making use of the Peltier heat developed by a small current run through the junction of a thermocouple located in an axial hole in the specimen (Fig. 2). In its present form, the limit of sensitivity of the calorimeter is a heat flow of 0.003 cal per hr. The copper used was the spectroscopically pure metal supplied by the American Smelting and Refining Co. in the form of 3/8 in. diam continuously cast rod, reported to be 99.999+ pct Cu. A small amount of the copper was available at the start of this work and is referred to hereafter as lot A. A second batch, lot B, was obtained later, most of the results described subsequently being for this lot. As will be seen, there is some indication that lot A was somewhat purer than lot B, but it is not known whether this difference was present in the as-received metal or arose during subsequent handling. The two lots of copper were remelted and cast into two 1½ in. diam ingots in vacuo, using high purity graphite crucibles and molds. The ingots were upset several times to break up the large cast grains, and then rolled and swaged to rods 0.391 in. in diameter, using several intermediate anneals with about 40 pct reduction in area between anneals. The penultimate anneal was 2 hr at 350°C. X-ray examination showed no marked general preferred orientation in the resulting rods. The grain structure typical of the two rods is shown in the micrograph of Fig. 4." It was found to be virtually im- possible to get an unambiguous measure of the absolute grain size in the two annealed rods because of the profusion of annealing twins and the lack of regularity of the grain boundaries. However, counts of the number of boundaries intersected per unit length along a random line on a polished section, making a correction for the proportion of boundaries (about half) estimated to be twin boundaries, gave a figure of about 0.015 mm for the average grain diameter. The grain size of the rod from lot A was about 5 pct smaller than that from lot B. The rods were cut into 1 ft long bars and these deformed in tension at room temperature to various total elongations in the range 10.8 to 39.5 pct. A strain rate of 1 pct per min was used. The deformed bars were then stored in a dry ice chest until such time as samples were to be cut from them. Five bars deformed as indicated in Table I were used for the subsequent tests. In all cases, all the calorimeter.

Jan 1, 1956

By E. I. Organick, B. H. Golding

A simple correlation is presented for the prediction of saturation pressures in condensate-gas and volatile-oil mixtures. Saturation pressure is related directly to the composition of the mixture with the aid of two generalized composition characteristics, B, the molal average boiling point, and W, the modified weight average equivalent molecular weight. The need for hydrocarbon equilibrium constants is entirely eliminated. Only the values of the two conlposition parameters need be obtained, and these are calculated in a simple and reproducible manner from the stream analysis of the mixture and the ASTM distillation for the heavy ends. The correlation is given .in the form of a set of 14 working charts in which saturation pressures, either retrograde dew points or bubble points, are plotted cs temperature, forming partial phase envelopes for mixtures having discrete values of the composition parameters, B and Wul. A locus of critical states on each chart intersects the partial phase envelopes, distinguishing retrograde dew point pressures from bubble pressures. A comparison Between experimental and predicted saturation pressures reveals that: the probable error of the predicted values, when considering the data as a whole (214 experimental points), is five per cent; for high gasjoil ratio condensate fluids (approximately 40.000 or more cu ft/bbl) the probable error is about 8 per cent. In either case, however, the probable error is comparable with the overall uncertainty of the data from which the correlation is derived. INTRODUCTION There is a present need for a simplified, yet reasonably accurate method for predicting upper phase boundaries of reservoir fluids. In the case of high gas/oil ratio fluids, namely the so-called highly volatile oils and the condensate gases, no simple method, accurate within 5 to 10 per cent, is now available by which bubble point and retrograde dew point pressures may be predicted. In order to calculate the upper phase boundary of a volatile reservoir fluid, using correlations now available, it is necessary to find and employ the proper K-values (equilibrium volatility ratios of the hydrocarbons in that fluid). This process of finding the Proper K-values usually involves a double trial and error computation. Since the K-values are in themselves dependent upon the composition of the fluid, their use in the calculation of a saturation pressure actually represents an unnecessary complication. The correlation described in this paper relates saturation pressure directly to the stream composition, entirely eliminating the need for K-values. The only data required to calculate the Stream composition are obtained from the customary low temperature fractional analyses of separator gas and liquidt and from the ASTM distillation of the c,+ fraction of the separator liquid. A considerable simplification in the procedure for predicting saturation pressures is thereby effected without significant loss in accuracy. BASIS FOR A CORRELATION Empirical relationships between the saturation pressure and the composition of the fluid in question have already been partially explored by one of the authors.V n particular, a relationship between the critical pressure for a hydrocarbon mixture and its composition was developed. The critical pressure is in reality a saturation pressure, as it repregents a limiting case either of a dew point or of a buhhle point pressure for any given mixture. It was found that the critical pressure may be correlated as a function of two generalized composition characteristics or variables. One characteristic expressed a molal average prop-erty, the other a weight average property of the mixture. Specifically, the molal average boiling point (MABP, or B as it

Jan 1, 1952

By Kefton Teague

The minerals discussed in this section have experienced a gradual, although not spectacular, growth in general. Obvious exceptions are the gradual decreasing use of talc and bentonite as filler materials, partly because of availability and relatively lower sales price of competitive materials. Mineral fillers and filter minerals are used principally in those countries that are heavily industrialized. Except for diatomaceous earth of filter grade, most industrialized countries are reasonably self-sufficient in the various filler and filter minerals. Prices of the various mineral commodities during the period 1950-1970 increased approximately as follows: barite, 43%; diatomaceous earth (filler), 49%; diatomaceous earth (filter), 55%; fuller's earth, 55%; talc. 77%; and bentonite, 94%. Actual usage of these mineral commodities as fillers and filters, during this period, showed changes approximately as follows: (1) Decrease-fuller's earth, 6%; talc, 15%; and bentonite, 29%. (2) Increase-barite, 113%; diatomaceous earth (filler), 150%; and diatomaceous earth (filter), -194%. A relationship between the amount of the various fillers and filters used and price increases is apparent. For example, barite increased only 43% in price, but its use as a filler has increased by 113%. On the other hand, talc, which increased 77% in price, decreased in filler use by 15%; and bentonite, which increased 94% in price, has decreased for filler and filter purposes by 29%. The actual decrease in the use of some of these commodities is not entirely caused by an increase in price. Competitive materials frequently have made substantial gains in the various filler and filter markets. For example, much of the bentonite used in the late 1940s and early 1950s for clarification of mineral and vegetable oils has been replaced by competitive materials. BARITE Occurrences and Sources In the United States, barite is produced from about 14 states, listed in approximate order of importance as follows: Missouri, Arkansas, Nevada, Georgia, Alaska, Tennessee, Kentucky, California, New Mexico, North Carolina, Washington, Idaho, South Carolina, Texas, and others. During the 20 years ending in 1970, almost equal amounts of barite were produced from Arkansas and Missouri. Within recent years, Nevada has replaced Georgia as the third leading barite--producing state. West Germany is second to the United States in barite production. Other important barite-producing countries include: Mexico, USSR, Italy, Greece, Canada, and Ireland. Ireland has become an important barite producer only recently. Barite is obtained from vein and cavity fill-

Jan 1, 1976