Search Documents

By G. B. Misra

While investigating on the aerodynamic resistance of airways supported with peripheral timber sets, at regular intervals, the following theoretical equations were developed by the author to estimate the resistance coefficient of such airways: [ ] for S < 1, where f is Darcy-Weisbach resistance coefficient of the airway, C is modified drag coefficient of the supporting member, D is equivalent diameter of the bare airway, 8 is ratio of the approach velocity over the sets to the average velocity of the bare airway, A is cross-sectional area of the bare airway, a is projected frontal area of the sets, A., is cross-sectional area of the air stream at the vena contracta inside the set, S is spacing of the sets, f, is resistance coefficient of the bare airway, l is length of aerodynamic influence of sets, p is perimeter of the bare airway, p, is setted portion of the perimeter of the bare airway, pe is unsetted portion of the perimeter of the bare airway, and P shielding factor. The equations were verified experimentally in a model rectangular airway supported with one- (bars), three-, and four-piece sets of square-section timber of three different sizes and were found to hold true. The work has been further extended to one-, three-, and four-piece sets of round timber of 2.6, 3.2, and 3.8 cm diam with the same experimental set up. Tests have been carried out for spacings of 25, 50, 75, 100, 150, and 200 cm over a regime of flow defined by the Reynolds number (with respect to the equivalent diameter of the bare duct) ranging from about 1.5 X 106 to 5 X 106 using the same experimental techniques. The values of f are calculated in the manner indicated in [Ref. 1]. Unlike with square-section timber, the resistance coefficient f of the airway setted with round timber shows a distinct variation with the Reynolds number of flow. This conforms to observations made by Sales and Hinsley.2 In order to have a comparable value of f for all types of sets with all sizes of timber, it was necessary to select the value of f at a fixed Reynolds number of flow. Since f is chiefly a function of the drag coefficient of the sets, the appropriate Reynolds number RE is that with respect to the diameter of timber in the set. Considering the diameters of timber used and the regime of flow over which measurements were made, f was chosen at a value of RE = 20,000 in all cases. The f vs. S curves are maximal in nature and in conformity with theory, the f vs. 1/S curves are straight lines up to a value of S = 1 beyond which they show a distinct flexure. The observed values of 1, the length of aerodynamic influence of sets, agree with the relation 1 = 42 e, developed for square-section timber sets, thus suggesting that the shape of timber has little influence on the length of aerodynamic influence. The value of the modified drag coefficient CD for round timber was calculated in the same way as for square timber in Ref. 1, taking the contraction factor Z = 1.5 for round-edged constrictions. CD has an average value of 0.96 with a standard deviation of 6.08% as compared to the free stream drag coefficient of 1.2 at RE = 20,000 for long cylindrical obstructions The shielding factor [ ] is plotted against S/1 in [Fig. 1]. The curves are more or less independent of the size of timber, but are different for the different types of sets, possibly due to their different degree of symmetry. Values of f calculated by the author&apos;s [Eqs. 1 and 2], using experimental values of CD&apos; and [ ] and taking I = 42 e, are plotted in [Fig. 2] against experimentally measured values of f for different types of sets with different sizes of round timber. The values agree closely with a standard deviation of only 5%, thus establishing the veracity of the theoretical equations developed by the author for round timber as well. A comparison was made between the Xenofontowa4 equations (the only other reasonable relations available for the estimation of the resistance coefficient of supported airways) and the author&apos;s [Eqs. 1 and 2] by comparing in [Fig. 3] the values of the resistance coefficient f computed by the Xenofontowa relations with those experimentally measured by the author. In order to make

Jan 1, 1975

By Douglas A. Sloan

Who would believe that young elementary school children could understand something as complex as the mining industry? The Challenge The challenge of accomplishing this is tremendous. An examination of Canadian school children indicated that they knew very little about the world of work in general, and hardly anything about the mineral resource industry in particular. It calls to mind the story about two youngsters who decided to play house. The little girl played her role well as she went about the house doing things she had watched her mother do every day. When it was the little boy&apos;s turn, he grabbed his lunch, waved goodbye to his "wife," jumped on his bicycle and pedalled furiously down to the end of the driveway-where he stopped. The youngster explained that he saw his dad go out of the driveway each morning, but he didn&apos;t know where he went, or what he did on the job. When you stop to consider the number of families today with two working parents, you can begin to appreciate the importance of the opportunities for role identity provided by this project. The Approach The challenge of teaching the school children of Canada about the world of work and, specifically, the mining industry is the challenge which the Canadian Institute of Mining and Metallurgy met with the Curriculum Development Research project. It started when a small, dedicated group of Vancouver members met Dr. Doreen Binnington. After this meeting, Dr. Binnington, an expert in curriculum development at the University of British Columbia, set herself to develop a curriculum program for the elementary shcools which accomplishes two main goals: It uses the "Identity Approach," developed by Dr. Binnington, an expert in curriculum development at the enable students to understand and appreciate the contribution of people, in this case, working with mineral resources. It has pupils enthusiastically exploring the importance of rocks, minerals, and the mining industry in their lives [(Fig. 1)]. Evolution of the Curriculum Development Research Project When the curriculum development research project was presented to the Vancouver Branch of the Canadian Institute of

Jan 1, 1981

By Frank Doxey

AT Dominion Steel & Coal Corp. it has long been recognized that continued mechanization of mine operations is necessary in the Pictou, Cumberland, and Sidney coal fields of Nova Scotia. The varied physical conditions in these fields call for special consideration of individual cases before planning is finalized. Because standard equipment cannot be procured which would operate successfully, many experiments have been necessary over the years to keep pace with the progress made in other countries. There are two mines, producing 2000 tpd, located in the Pictou coal field. The field is badly distorted and crossed by many faults. Seams are highly inclined and irregular and vary in thickness from 5 to 40 ft. Entries are difficult to maintain because of squeezing of the coal ribs and movement of the roof and pavement.

Jan 7, 1954

For the convenience of members who may be traveling from place to place, the Secretary has compiled a list of libraries or other places in the United States and foreign countries where MINING AND METALLURGY or the Transactions may be consulted. This list will be. sent to members if they so request. LIST OF THE MEETINGS OF THE INSTITUTE AND THEIR LOCALITIES FROM ITS ORGANIZATION TO MARCH, 1920

Jan 1, 1925

By J. L. Craig, C. L. Edwards, M. D. Harper, J. M. Ray

The Los Alamos National Laboratory executed 19 intermediate scale cratering experiments in oil shale at the Colony Mine in Garfield County, Colorado. These experiments have led to a better under- standing of fracture characteristics and fragmentation of & - oil shale by use of a conventional high explosive. Geologic site characterization included detailed mapping, coring, and sample analyses. Site-specific geology was observed to be a major influence on the resulting crater geometry. The joint patterns at the experimental site frequently defined the final crater symmetry. Secondary influences included vugs, lithology changes, and grade fluctuations in the local stratigraphy. Most experiments, in both the rib and floor, were conducted to obtain data to investigate the fragmentation results within the craters. The rubble was screened for fragment- size distributions. Geologic features in proximity to the explosive charge had minimal effect on the rubble due to the overpowering effect of the detonation. However, these same features became more influential on the fracture and rubble characteristics with greater distances from the shothole. Postshot cores revealed a direct relationship between the grade of the oil shale and its susceptibility to fracturing. The Colony Mine experiments have demonstrated the significant role of geology in high explosive/oil shale interaction. It is probable that this role will have to be considered for larger applications to blast patterns and potential problems in retort stability in the future of oil shale development.

Jan 1, 1983

Discussion of the paper of GEORGE K. BURGESS and SIR ROBERT A. HADFIELD, presented at the New York meeting, February, 1915, and printed in Bulletin No. 98, February, 1915, pp. 455 to 468. ALBERT SAUVEUR, Cambridge, Mass.-There is a definiteness and finality in the investigations that have been conducted by the Bureau of Standards and in the method of presenting the results that is most satisfactory and refreshing.. A year ago Dr. Burgess and his co-workers investigated the question of critical points in carbonless iron, and they settled the question once for all. No one can now claim that the thermal point A2 in carbonless iron does not exist. At the past meeting of this Institute in Pittsburgh, Dr. Burgess showed the worthlessness of the shrinkage clause. To my mind after his demonstration no one can again claim that the shrinkage clause renders any service. He also showed us that it was a practicable proposition to use pyrometers in steel work in order to ascertain the finishing temperatures of rails. No one can again come before this body and make the claim that it is not a practical proposition. And now Dr. Burgess shows us that steel ingots can be made in a commercial way, practically free from pipe, from segregation, aid from blow holes. It places again before us in a very clear manner the question of piped ingots and of segregation, a question which has been debated for 20 years or more. I know very well the attitude of the standpatters in the matter. They claim that most of the pipe is removed in the discard, and that if a little is left it is so thoroughly welded that it does no harm. I for one am not convinced of the soundness of the argument. I do not believe there is any one present who would claim that, given an ingot free from pipe, free from segregation, and free from blow holes, better rails will not be made out of that ingot than out of the ordinary piped or segregated metal which is used by almost all of our steel mills. In my opinion, if we give our sanction to the casting of steel in the shape of piped or segregated steel ingots, we are guilty. If we give our sanction to the rolling of rails from such metal, we are guilty. It is our duty as experts, as steel makers, and as steel consumers to make and to use the best steel obtainable on a commercial basis, for the manufacture of rails. Now, we have been shown that sound ingots can be produced from which superior rails can be made. If we do not insist upon these sound ingots, then we fail in our duty. I think that the art of casting steel ingots has advanced to such a point that the casting of steel ingots piped and segregated ought no longer to be tolerated.

Jan 5, 1915

By E. A. Anderson, P. W. Ramsey, E. J. Boyle

Only a few zinc-rich alloys are in commercial use today, and these depend largely upon solid solution effects for their desirable properties. Typical examples are rolled alloys containing about 1 Per cent of copper, with Or without additions of elements such as magnesium, and die-casting alloys containing about 4 Per cent of aluminum with small amounts of magnesium and sometimes copper." A number of elements are capable of forming alloys with zinc, Which do not enter into solid solution except in limited degree. The Present Paper considers One such system, zinc-titanium, in which alloys having potentially useful properties in the rolled form were found. Zinc-titanium System The zinc-rich portion of the zinc-titanium diagram, as determined by standard methods in this laboratory,3 is shown in Fig. I. The portion of the diagram of significance in the present work extends from 0 to about 0.5 per cent titanium. Gebhardt4 places the eutectic at 0.45 per cent, but the evidence in favor 01 the composition given in Fig. I is considerable. The solid solubility of titanium in zinc is very low indeed and possibly places these alloys in a somewhat different category from the commercial alloys previously mentioned. Alloy Preparation All of the alloys used in this work were prepared with titanium metal of 98.9 per cent purity. In most cases high-purity zinc (99.99 per cent) was used but sufficient work was done later to show that zinc of about high-grade composition would yield approximately equal results. Best practice in alloy manufacture seemed to be to prepare a zinc-titanium hardener by adding about 4 per cent of titanium metal to molten zinc and holding under a boric acid cover, with frequent stirrings, at 750°C, until the titanium had dissolved. The desired titanium content could readily be obtained in the final alloy by adding the calculated amount 01 this hardener. The alloys proved to be quite stable in composition, unless overheated, and, with reasonable temperature control, required no cover or flux to prevent loss of titanium content by oxidatioll, Hot-rollig Tests Three alloys containing, by analysis, 0.05, 0.12, and 0.23 per cent titanium were selected for preliminary study. Slab cross sections a a marked grain refinement* (Fig. 2) in the two alloys of highest titanium content. Cast unalloyed zinc has a columnar grain structure similar to that shown for the alloy of lowest titanium content but without the scatter of small equiaxed grains at the center.

Jan 1, 1944

By P. W. Ramsey, E. J. Boyle, E. A. Anderson

Only a few zinc-rich alloys are in commercial use today, and these depend largely upon solid solution effects for their desirable properties. Typical examples are rolled alloys containing about 1 Per cent of copper, with Or without additions of elements such as magnesium, and die-casting alloys containing about 4 Per cent of aluminum with small amounts of magnesium and sometimes copper." A number of elements are capable of forming alloys with zinc, Which do not enter into solid solution except in limited degree. The Present Paper considers One such system, zinc-titanium, in which alloys having potentially useful properties in the rolled form were found. Zinc-titanium System The zinc-rich portion of the zinc-titanium diagram, as determined by standard methods in this laboratory,3 is shown in Fig. I. The portion of the diagram of significance in the present work extends from 0 to about 0.5 per cent titanium. Gebhardt4 places the eutectic at 0.45 per cent, but the evidence in favor 01 the composition given in Fig. I is considerable. The solid solubility of titanium in zinc is very low indeed and possibly places these alloys in a somewhat different category from the commercial alloys previously mentioned. Alloy Preparation All of the alloys used in this work were prepared with titanium metal of 98.9 per cent purity. In most cases high-purity zinc (99.99 per cent) was used but sufficient work was done later to show that zinc of about high-grade composition would yield approximately equal results. Best practice in alloy manufacture seemed to be to prepare a zinc-titanium hardener by adding about 4 per cent of titanium metal to molten zinc and holding under a boric acid cover, with frequent stirrings, at 750°C, until the titanium had dissolved. The desired titanium content could readily be obtained in the final alloy by adding the calculated amount 01 this hardener. The alloys proved to be quite stable in composition, unless overheated, and, with reasonable temperature control, required no cover or flux to prevent loss of titanium content by oxidatioll, Hot-rollig Tests Three alloys containing, by analysis, 0.05, 0.12, and 0.23 per cent titanium were selected for preliminary study. Slab cross sections a a marked grain refinement* (Fig. 2) in the two alloys of highest titanium content. Cast unalloyed zinc has a columnar grain structure similar to that shown for the alloy of lowest titanium content but without the scatter of small equiaxed grains at the center.

Jan 1, 1944

By J. Ostachowicz, B. Holynska, M. Lankosz

The paper presents an analyzer and the method for the continuous determination of weight percentage of ore grains with diameter smaller than 75 µm in mineral slurries. The method is based upon the measurement of characteristic x-rays of copper excited by primary radiation of two different energies 16.5 keV and 60 keV from Pu238 and Am241 sources respectively. Additionally the backscattered primary radiation is measured in order to correct the variations of the solids content in the slurry. Since the particle size distribution of slurry can be described by the Rosin-Rammler formula, some calculations have been carried out in order to evaluate the influence of distribution parameters upon the results of the measurements of weight percentage U75 of particles smaller than 75 µm. The influence of solids content and of the copper concentration variation on the results has been also evaluated.1 It resulted from the calculations that the ratio rl/rz, where rl and r2 are the relative intensities of copper characteristic x-rays excited with 16.5 keV and 60 keV photons respectively does not depend on the copper content within the range 1 % to 4% of copper and is slightly dependent on the solids weight fraction and its chemical composition. The change of the dispersion parameter of the Rosin- Rammler distribution from 0.5 to 0.9 results in a change of value of U75 of approximately 3.0%. The results of calculations have been confirmed by the results of laboratory experiments. Therefore, a prototype of industrial analyzer for continuous determination of weight percentage of particles smaller than 75 µm has been designed and made. Its schematic drawing is shown in [Fig. 1]. Slurry is flowing down through steel flow-cell of the length equal to approx. 2 m. In the center, two XRF measuring heads (1) and (2) are located. Each of the heads comprises a rigid waterproof cover (3) with the mylar window (4), in which a proportional counter of resolution 15% for 6.4 keV is mounted with a preamplifier (5). The low- energy isotope source (6) is centrally located above the detector

Jan 1, 1980

By P. W. Ramsey, E. J. Boyle, E. A. Anderson

ONLY a few zinc-rich alloys are in commercial use today, and these depend largely upon solid solution effects for their desirable properties. Typical examples are rolled alloys containing about I per cent of copper, with or without additions of elements such as magnesium,1 and die-casting alloys containing about 4 per cent of aluminum with small amounts of magnesium and sometimes copper.2 A number of elements are capable of forming alloys with zinc, which do not enter into solid solution except in limited degree. The present paper considers one such system, zinc-titanium, in which alloys having potentially useful properties in the rolled form were found. ZINC-TITANIUM SYSTEM The zinc-rich portion of the zinc-titanium diagram, as determined by standard methods in this laboratory,3 is shown in Fig. I. The portion of the diagram of significance in the present work extends from 0 to about 0.5 per cent titanium. Gebhardt4 places the eutectic at 0.45 per cent, but the evidence in favor of the composition given in Fig. I is considerable. The solid solubility of titanium in zinc is very low indeed and possibly places these alloys in a somewhat different category from the commercial alloys previously mentioned. ALLOY PREPARATION All of the alloys used in this work were prepared with titanium metal of 98.9 per cent purity. In most cases high-purity zinc (99.99 per cent) was used but sufficient work was done later to show that zinc of about high-grade composition would yield approximately equal results. Best practice in alloy manufacture seemed to be to prepare a zinc-titanium hardener by adding about 4 per cent of titanium metal to molten zinc and holding under a boric acid cover, with frequent stirrings, at 750°C. until the titanium had dissolved. The desired titanium content could readily be obtained in the final alloy by adding the calculated amount of this hardener. The alloys proved to be quite stable in composition, unless overheated, and, with reasonable temperature control, required no cover or flux to prevent loss of titanium content by oxidation. HOT-ROLLING TESTS Three alloys containing, by analysis, 0.05, 0.12, and 0.23 per cent titanium were selected for preliminary study. Slab cross sections revealed a marked grain refinement* (Fig. 2) in the two alloys of highest titanium content. Cast unalloyed zinc has a columnar grain structure similar to that shown for the alloy of lowest titanium content but without the scatter of small equiaxed grains at the center.

Jan 1, 1944

By G. W. Gross

A commercial deposit of white kaolinite clay contained in the sandy overburden of the Cambrian Gatesburg formation in Central Pennsylvania was successfully mapped by combined SP and resistivity methods and results were checked by drilling. Resistivity minima in the range between roughly 2000 and 3500 ohm-meters coupled with second-order SP maxima of 50-60 mV contrast were found to characterize commercial white kaolinite clay beneath not more than 30-40 ft. of sandy overburden in the area stdied. This investigation supports the hypothesis, established previously, that certain SP phenomena may reasonably be ascribed to diffusion and membrane potentials produced by interaction of clay lenses, sandy matrix, and ground waters. The success of this test proves that this prospecting technique can assist in locating clay deposits in sandy overburden derived from the weathering of sandstones and carbonate rocks such as the Cambrian formations of Central Pennsylvania. In a recent paper, Gross and Moore (1959) described broad self-potential minima above the outcrops of the Cambrian Gatesburg formation. These "first-order" SP anomalies, of 220-350 mV contrast (Figure 7), are related to the peculiar sandy residual soil covering the Gatesburg formation. Small positive ("second-order") peaks of 50-60 mV contrast are superposed on the bottom or flanks of the first-order troughs. They appear to be related to lenses and layers of kaolinite clays within the sandy Gatesburg overburden. Both first-order and second-order anomalies show a characteristic inverse relationship with apparent resistivity profiles in most cases. An explanation in terns of liquid-junction and shale potentials was advanced. According to this working hypothesis, shale potentials are generated: 1) at the contact of the sandy Gatesburg overburden with the more argillaceous soils of surrounding formations; 2) at the boundary of clay lenses contained in the sandy matrix of that overburden. Concentration gradients between interstitial infiltration waters and perched water tables within the Gatesburg overburden are believed to give rise to the liquid-junction potentials. In order to test this hypothesis further, a detailed study was carried out of a second-order positive anomaly on the property of the Woodbury Clay Co. at Mines (Blair County, Pa., Hollidaysburg folio of the U.S. Geological Survey). A second aim was to establish if combined SP and resistivity surveys are suitable as a practical method for delimiting favorable areas in which commercial kaolinite clay de~osits may be found by drilling. Drilling control was provided by the Woodbury Clay Co. PROCEDURES Instrumentation used for SP measurements was the same as described in the paper mentioned. For resistivity surveys, a direct-current voltmeter-ammeter device built by Georator Gorp. of Manassas (Va.) was used in combination with non-polarizing electrodes from the same manufacturer. Power was supplied by one to six 45-volt, heavy-duty B-batteries

Jan 1, 1961

By C. A. Siebert, S. H. Bush

Isothermal temper-embrittlement studies were conducted on a 5140 steel at various temperatures for times as long as 3000 hr. Specimens from the embrittled steel were subjected to impact tests, metallographic examination, microhardness, and lattice-parameter measurements. SEVERAL of the steels in the low alloy group are subject to a pronounced decrease in impact energy if held within, or cooled slowly through, a range of temperatures below the lower critical. This phenomenon, known as temper embrittlement, is quite pronounced in the chromium steels of which AISI 5140 is typical. This study considered the response of one heat of 5140 steel when embrittled isothermally at various temperatures for times as long as 3000 hr. Excellent reviews of the work done in the field of temper embrittlement have been written by Hollomonl and Woodfine.&apos; Both authors list the various theories which have been advanced to explain temper embrittlement. Some of the mechanisms considered were: 1—a transformation below 700°C; 2—an allotropic modification of iron; 3—precipitation from the ferrite of such compounds as carbides, nitrides, phosphides, or chromium oxides; 4—decomposition of retained austenite; 5—modification of special carbides; 6—grain-boundary segregation; and 7—selective distribution of carbides. The present study investigated the changes in hardness, Meyer&apos;s number, impact properties, micro-structure, and lattice parameter which occurred on embrittlement. Previous studies considered the influence of microstructure and of prior austenitic grain size3 on the response of 5140 steel to temper embrittlement. Equipment and Procedure All samples were taken from one heat of 5140 steel; the chemical composition of this steel was: 0.43 pct C, 0.86 pct Mn, 0.020 pct P, 0.019 pct S, 0.27 pct Si, 0.84 pct Cr, 0.10 pct Ni, 0.06 pct Mo, 0.10 pct Cu, and the remainder Fe. The material was received as % in. rounds. This stock was cut down to blanks measuring approximately 0.425~0.425~2.196 in. Heat Treatment: The rough blanks were normalized at 1600°F (870°C) for 1 hr, then austenitized at 1600°F (870°C) for 1 1/2 hr, and quenched into an agitated oil bath. The specimens were tempered at 1275°F (690°C) for 5 hr and water quenched. These tempered specimens were designated as the toughened state. Embrittling Treatments: The tempered bars were divided into sets and subjected to the various embrittling treatments listed in Table I. Temperatures from 750" to 1050°F were investigated for times of 1 to 3000 hr. Special tests to determine the effect of heating a short time at a higher temperature after long-time embrittlement at some lower temperature were also conducted. All specimens were water quenched at the end of the embrittling cycle, then ground and notched to obtain standard Charpy V-notch specimens. Impact Tests: The bars were fractured in a 260 ft-lb Charpy impact unit; specimens were fractured at temperatures ranging from —315°F to room temperature. Fixed temperatures used consisted of —315°F with liquid nitrogen, —115°F with dry ice and acetone, and 32°F with ice and water. Intermediate temperatures were obtained by suspending the bars in a jig over the liquid nitrogen, dry ice and acetone, or ice and water.

Jan 1, 1955

By C. A. Hartnagel

During- the past 10 years the annual production of petroleum in New York has averaged close to 5,000,000 bbl., the total for the period being 49,881,000 bbl. In 6 of the 10 years, the production was slightly in excess of the 5,000,000 mark. The 1944 production of 4,697,000 bbl. represents a 7 per cent decline from the previous year. Of the total 1944 output, the Allegany County district, which includes two small areas of Steuben County, contributcd 3,614,065 bbl., a decline of 5 per cent from 1943, and the contribution of Cattaraugus County, which represents the northern extension of the Bradford pool of Pennsylvania into New York was 1,082,935 bbl., a decline of more than 14 per cent. Since March 1942, the posted price of New York crude oil has remained at $3.00 per bbl. On lug. I, 1944, a Federal subsidy of 75¢ per bbl. was granted to oil producers, thus making the price actually $3.75 per bbl. Since all of the oil produced in New York comes under the designation "stripper well operations," it is entitled to the Federal subsidy. During the last few years there has been little change in the number of wells drilled annually. In the Allegany field, which accounts for three fourths of the oil produced in the state, 1240 wells, including water-intake wells, were drilled during 1944 as compared with 1223 in 1943. There was no marked increase in the number of wells drilled after granting the subsidy of 75¢ per bbl. of oil on Aug. I, the increase being but 14 wells during the last half of the year over the preceding six months. In flooding operations it is not to be expected that even a substantial increase in the price of crude oil will be reflected quickly in an increase of the number of wells drilled or in a marked increase in production of crude oil. In flooded areas, oil is obtained through a program extending over a number of years. This program involves the drilling of the water or input pressure wells, drilling of the oil wells, building up the oil flood to maximum production, and finally the watering out of the well when the amount of oil produced in proportion to the water becomes so small that pumping is no longer profitable. The various operations may extend over a period of 10 years or more, during which time the price of crude may have fluctuated greatly. Although the rate of production can be controlled to a limited extent, it is evident that a flood when once begun must be continued regardless of the price of crude. During the past seven years New York crude has had a price range from $1.68 per bbl. in 1938 to the present price of $3.75 per barrel The field pattern now in general use for wells in a flood project is the "five-spot." Under this arrangement, the lease is divided into squares with a water well at each corner and an oil well in the center. In the all-over pattern of the lease each oil well is acted upon by four water wells and each water well supplies part of the pressure to four oil wells. Spacing between the input water wells and the oil wells usually varies from zoo to 225 ft. or, on an acre basis, there is one oil well and one water well for each 2 1/2 acres. In recent years there has been a tendency to increase

Jan 1, 1945

By C. N. J. Wagner, E. N. Aqua

The bee alloys of the terminal solid solution of rhenium in niobium were investigated by X-ray diffraclion methods. The analysis of the broadening of the powder pattern peaks from the niobium-rich alloys, cold-worked by filing, showed evidence for faulting on (211) planes. The alloys with larger rhenium concentrations were brittle, and fractured when filed. The analysis of the shapes of the diffraction profiles from powders produced by hammering with steel plates) of these brittle alloys indicated that the broadening was due predominantly to platelets bounded by clibe planes. This result was consistent with the Laue patterns from single-cleazlage facets which showed evidence for clearage fracture on {100} planes. The influence of faulting on the mechanical properties of face-centered cubic (fcc) metals and alloys, i.e., how faulting affects the various dislocation configurations in fcc metals, is well-known.&apos; The important question is whether or not faulting occurs in body-centered cubic (bcc) metals and alloys, and, furthermore, if faulting does occur, to what extent it affects the mechanical properties. Theoretical calculations indicate that the stacking-fault energy is rather high in most bcc metals.2 The results of sev-eral studies using transmission electron microscopy have indicated that faults are present in well-annealed and lightly deformed bcc metals and alloys, such as tungsten,3 vanadium,4 and Mo-Re alloys.5,6 These faults, as have been observed, may be stabilized by the presence of interstitial (C,N,O) atom segregation to the extended dislocations. In addition, there is considerable X-ray diffraction evidence for faulting in bee metals,7-8 using the same techniques that were successful for the study of faulting in fee metals and alloys.7 This X-ray diffraction method is currently the only technique applicable for the investigation of faulting in metals with high stacking fault energies, i.e., when severe amounts of deformation are required to produce sufficient amounts of faulting to be detectable by X-rays. The thinned films of heavily deformed metals will become opaque in the electron microscope due to the high dislocation densities present. In a previous investigation of faulting8 in bee metals of group Vb and VIb, the authors observed that niobium was ductile when filed at room temperature, and showed the highest density of faults on the (112) family of planes. A niobium-base alloy system was therefore chosen to study the effect of alloying on the occurrence of faults in a bcc alloy. There is a large range of terminal solid solubility of rhenium in the alloys of the bee refractory metals. All of the Group VIb-rhenium alloys, i.e., Cr-Re, Mo-Re, and W-Re, exhibit solid solution hardening without loss of ductility.9 In fact, the ductility reaches a maximum for alloys with compositions near to the limits of solubility. This enhanced ductility has been attributed to the lowering of the stacking-fault energy in the alloy; i.e., the increased amounts of twinning provide an additional mode of deformation, resulting in the observed high ductility.&apos; Because of this demonstrated effect of rhenium in bee alloys, it was decided to study a series of alloys of Nb-Re. Using the same X-ray diffraction methods as described in the previous investigation,&apos; one is able to identify the possible causes of broadening of the powder pattern peaks, e.q., particle size, microstrains, stacking faults, and/or twin faults. The separation of these various contributions to the measured peak shape is accomplished by the Warren-Averbach analysis.7 I) EXPERIMENTAL PROCEDURE A series of seven bee solid solution alloys containing from 2.5 to 21.5 at. pct Re (remainder niobium) were prepared at the General Electric Research Laboratory. Buttons, weighing 25 g, were alloyed from electron-beam-melted niobium chips and random rhenium sheet by arc melting in a water-cooled copper crucible, under an argon atmosphere. The buttons were inverted and completely remelted to promote homogenization. The nominal alloy compositions are listed in Table I. Samples of the cold-worked alloys were obtained by filing to produce a powder for the X-ray study. Alloys too brittle to be filed were hammered with steel plates. The resultant filings or brittle impactings were screened through 150-mesh classifiers and compacted to the required shape for the diffractometer holder. The X-ray diffraction peaks were automatically recorded by fixed time counting at uniform 28 intervals, or by continuous registration with a ratemeter. In all cases, the (110)-(220) and (200)-(400) pairs of peaks and the (211), (310), (222), and (321) reflections were measured on a GE-XRD5 diffractometer using CuKa radiation with nickel filter or MoKct radiation and a LiF monochromator in the diffracted beam. The first part of the data reduction, completed with the aid of a series of programmed computations,10 was the analytical resolution of the Kol component of the diffraction profile. Subsequent computations were then made with reference only to the resolved Kol peak shape. These included the measurement of the

Jan 1, 1967

By Dorsey Hager

North Central Texas has recently become a center of interest for the oil men of America. The bringing in of the McClosky well at Ranger, Eastland County, and the shallow pool at Brownwood, Brown County, in 1917, has stimulated interest in this area to fever pitch. Oil men from all over the United States are now investing there. The area of present interest is shown by the accompanying map (Fig. 1). The money spent in leases runs into millions of dollars. It is no exaggeration to say that a strip of country 200 miles (321 km.) long and 125 miles (201 km.) wide, comprising some 15,000,000 acres (6,070,310 ha.), has been leased practically solid at a cost for rentals and bonuses of at least $1 per acre. The test holes contracted for will certainly number 400, at a cost of at least $5,000,000. From what has been done in the past six months, $20,000,000 at least will be spent. To pay returns on this amount of money, new production to the extent of at least 12,000,000 bbl. must be obtained. At present, the production from new fields will not average over 5000 bbl. per day; three wells at Ranger are producing 3000 bbl.; 250 wells at Brownwood produce 1000 bbl.; and the Gray well, Coleman County, is as yet an unknown factor. However, at Ranger there is every indication of developing a good pool covering from 1500 to 2000 acres (607 to 809 ha.), more or less, but the wells are deep, 3400 to 3800 ft. (1036 to 1158 m.), and cost $35,000 to $40,000 to drill. Large wells are necessary to pay for such expensive holes. As new wells are drilled, the gas pressure will be lowered rapidly, and large production need not be expected. For those oil men who expect a second Cushing or an Eldorado, Ranger holds little of promise. At Brownwood, Brown County, there are some 250 shallow wells (depths from 200 to 350 ft.) averaging 4 to 7 bbl. per day. There is a chance of an extensive producing area for these shallow sands to the southwest, and the opening of several thousand acres of shallow oil territory, and also some promise of deeper oil horizons in the Ranger horizon, but probably all under 2500 ft. At present, the lease brokers and speculators, and only a handful of oil men, have made any money. More fields must be developed, and it is more particularly with these possibilities that this paper deals. Lack of water for drilling purposes has undoubtedly held back development so far this year; this part of Texas has had a drouth for two years and there is an actual scarcity of water. Geological investigations so far undertaken cover nearly all the area outlined, and while pakt of the

Jan 1, 1920

By Henry Lewelling

An experimental investigation of the relative effectiveness of standard bullets and "shaped charges" in perforating dense, hard formations is reported. A method is described which simulates the conditions under which a shot is normally fired. Results are evaluated on the basis of depth of penetration, extent 01 Fracturing. extent and nature of formation damage, and other physical characteristics. INTRODUCTION A study was made of the relative merits of bullets and "shaped charges&apos;&apos; as applied to well completions in hard, dense formations such as those encountered in the Permian Basin. The planning of the laboratory program stipulated that core samples should be prepared and mounted in such a way that perforation shots of either kind"" could be fired into them, keeping the factors pertinent to good shooting practice similar to what they would be in a well. The shooting was done in a buried tank. with the sample and shooting equipment covered with water. The depth of water was calculated to he sufficient to simulate the inertial effects of well fluids for the duration of an explosion (a few micro-seconds). Flow measurements were attempted on the specimens after perforation. Due to the lack of uniformity of the limestone, shale breaks. etc., these measurements proved to be of little value to the study. The mounting materials were removed. so that the character of the penetration. fracturing, etc., could be observed. METHOD Laboratory samples were selected from the hard. dolomitic sand cores from Block 31 Field. Core pieces having a 3 3/4 in. diameter and a useful length of 10 to 12 in. were used. Selection was aimed at those pieces having a minimum of shale streaks and other irregularities. The ends were cut off square Manuscript received in the Petroleum Branch office June 28, 1951. Paper presented at the Petroleum Branch Fall Meeting in Oklahoma City, Okla., Oct. 3-5, 1951. with the diamond saw. Prior to lbeing mounted. the cores were soaked in water to prevent them from absorbing water out of the wet concrete, thus weakening it. A set of steel capsules was fabricated for holding the core Samples. Seven-in. casing was cut in two-ft lengths. of which one end was closed by "orange-peeling" and welding, and the other was threaded to accept a standard bull plug. The bull plugs were fitted with copper tube connections .so that pressure could be applied when the capsules were made up. The cores were mounted in the capsules by means of wire centralizers whose function was to hold the Core in proper position while concrete was poured and set. A special aggregate was prepared wing a graded sand and gravel mixture

Jan 1, 1952

By J. E. Strassner

Oilfield emulsions are stabilized primarily by film-forming asphaltenes and resins containing organic acids and bases. Adding inorganic acids and bases radically changes the physical properties of these films and their emulsion-stabilizing properties. Interfacial films show one of three different physical characteristics when retracted in pendent drop tests. These compressed films have rigid, soap-type or minimum film properties depending on the quantity of asphaltenes and resins in the crude oil and on the pH and composition of the brine. There exists for each crude oil-brine system an optimum pH range over which the adsorbed film exhibits minimum contracted filtn properties. In this range, intmfacial tension is high — frequently near its maximum value — indicating the absence of highly surface-active specier; crude oil-brine emulsions generally show minimum stability; and surfactant requirements for breaking these emulsions are significantly reduced — sometimes no surfactant is needed. About two-thirds of the world&apos;s crude oil is produced as emulsions that must be treated (demulsified) to be marketed.&apos; Approximately three-fourths of all domestic crude oil produced must be treated. The percentage of crude requiring treatment increases as fields become older and more water is produced. Demulsification most frequently is attained through use of surfactants, heat and electric treaters. It is estimated that over 75 percent of all oilfield emulsions are broken by chemicals generally containing alkylene oxide condensates. Although acids and bases are known to affect emulsion stability:-&apos; they rarely are used in the oil field except in batch treatment of the most severe emulsions. Nevertheless, pH adjustment by using acids or bases in demulsification has some advantages over other methods. Mainly, it is cheaper. Acids and bases frequently are cheaper to use than surfactants, or can appreciably reduce the amount of surfactant required for demulsification. Secondary advantages are that less oil is lost by emulsi-fication into the aqueous phase, and that less corrosion is encountered when the optimum pH is basic. Limitations to the use of pH include (1) use in brines containing high concentrations of reactive ions, (2) closer supervision for pH control than is required for surfactants and (3) need for corrosion protection when the optimum pH is sufficiently acidic. These factors indicate that the economics of pH con trol in demulsification will be maximized when relatively large treating facilities are needed, when relatively large surfactant concentrations are required to break an emulsion, when a relatively low concentration of the aqueous phase is emulsified in the oil and when the emulsified aqueous phase contains relatively low concentrations of reactive ions. Because there are no broad guide lines for using pH control in breaking oillield emulsions (and because the limited guides available are highly specific and frequently contradictory), this paper will attempt to clarify the principles involved in using acids and bases to break emulsions. These principles also should be useful in refinery separations and in other oilfield applications where stable or unstable petroleum emulsions are involved. Principles of Emulsion Stability Oilfield emulsions generally occur as water droplets dispersed in oil (w/o) and occasionally as oil droplets in water (o/w). These emulsion droplets are usually in the 0.1- to 10-micron range. However, more coarsely dispersed water droplets frequently are present in the emulsion. Pure hydrocarbons and water will not form stable emulsii except in extreme dilutions where the large distance brtween droplets inhibits coalescence. An emulsion breaks because interfacial tension acts to minimize the surface area of the dispersed drops by coalescence. However, emulsions can be stablized for long periods of time by the presence of a third phase that adsorbs at the oil-water interface and inhibits coalescence of the dispersed phase."&apos; Emulsions generally are stabilized by (1) repulsive charges on the surfaces of the dispersed phase and (2) adsorbed films that, being preferentially wetted by the continuous phase, act as a physical barrier to inhibit contact between the dispersed droplets. Both these factors generally are important in stabilizing and in breaking o/w emulsions. However, repulsive charges are less effective in stabilizing w/o emulsions which generally are stabilized by adsorbed films.V or this reason the nature and importance of these films at oil-water interfaces were examined closely; as will be shown, pH changes were found to affect the films significantly, and this work led to laboratory tests of pH- adjustment in emulsion breaking. This paper will present evidence to show that emulsions are stabilized primarily by films that form around droplets

Jan 1, 1969

By C. J. Leith

A study of the effect of rock composition, rock structure and degree of weathering on the stability of cut slopes is being sponsored jointly by the U.S. Bureau of Public Roads and the North Carolina Highway Commission. In 58 mountain and piedmont counties of North Carolina the percentage of failed cut slopes is greatest in micaceous metasediments, gneisses, and schists, and in saprolite and soil derived from these rock types. Soil slope failures outnumber rock slope failures by two to one. Joints and similar planes of separation exert a strong influence on size and shape of the sliding mass. They may or may not act as failure surfaces, depending on their orientation with respect to the active forces. Climatological data, though indicative of weathering conditions, do not correlate well with slope failure frequency. Because of the presence of joints and similar planes of weakness in soil and rock materials, conventional methods for analyzing slope stabilities are not directly applicable. Empirically derived modifications of these methods are being investigated. A study of the stability of highway cut slopes, sponsored by the U. S. Bureau of Public Roads and the North Carolina State Highway Commission, began in 1962 at North Carolina State of the University of North Carolina at Raleigh. As part of this study all slides, rockfalls and other types of cut slope failures on Federal and State highways in the 58 mountain and piedmont counties in North Carolina were located and described, and the data catalogued in a punched card file system. A major objective of the project is to relate slope failures to properties and physical conditions of the geological units in which the slopes were constructed, and to correlate soil type and/or geological unit with type and frequency of slope failure. The complexities of the problem of slope stability and the limitations which these complexities impose on methods for analyzing slopes have been recognized for many years. A great variety of factors and processes may lead to slides, often making it almost impossible to analyze theoretically the conditions required for stability of slopes. One of the principal factors determining maximum safe slopes is the shear strength of the material in which the slopes are cut, but unfortunately there are very few data available concerning shear strengths of residual soils. Vargasl tested clay derived from gneiss and granite in southern Brazil; the properties of decomposed granite occurring near Hong Kong were determined by Lumb.2 These data are being used, when applicable, to supplement the test data obtained in the present study by Yorke.3 The locations of the North Carolina slope failures, more than 400 in number, are shown on Fig. 1. This map, adapted from the Geological Map of North Carolina,4 suggests the possibility of a relationship between frequency of slide occurrence and rock type. However, the evaluation of this possibility requires consideration not only of the type of rock, but also of its large and small scale structural features, its susceptibility to and degree of weathering, and the composition and structure of the weathering products. Soil slope failures in thoroughly weathered soil material and saprolite outnumber rock slope failures two to one. INFLUENCE OF ROCK TYPE The agricultural soil type involved in each soil slope failure was identified and each failure was catalogued in terms of the parent material from which the soil was derived. These data indicate that most of the slope failures, whether in the rock or in the derived soil, are associated with metamorphic rocks (see Fig. 2a). The data may be skewed somewhat because of the relative sizes of the total areas underlain by the various rock types, but Leith and Gupton5 have demonstrated that the preponderance of failures in metamorphic rocks is of much greater magnitude than could be accounted for by the areal factor alone. The dominance of metamorphic rocks is emphasized when soil slope failures are considered in terms of the specific rock types from which the soils were derived (see Fig. 2b). In particular, mica schists and mica gneisses account for more slides

Jan 1, 1965

Two separate but closely related projects now under construction on the St. Lawrence River- the Seaway and the St. Lawrence Power Project- are providing the impetus for what may become one of the most significant economic expansions in the Northeast. By 1959, or even earlier, electric power will be flowing from the largest single hydroelectric installation east of the Rockies. Simultaneously there will come into existence a great new commercial waterway which will provide cheap transportation from the farm and industrial heartlands of the U. S. and Canada to the markets and resources of the world. When the Seaway is completed, vessels with five to ten times the capacity of those now using the Canadian canal system will be able to move from the Atlantic Ocean to Lake Superior.

Nov 1, 1955

By R. B. Russell

The expansion coefficients of hexagonal (a) zirconium have been calculated from the lattice expansionparameters of both coefficientsofhexagonallow and high hafnium alloys in the range 0° to 600°C. It is found parametersofboththat the coefficients are straight-line functions of the temperature and that the effect of hafnium is to depress the mean coefficients by about 1 pct at room thattemperature and 9 pct at 600°C. The cubic (ß) form was stabilized so that its coefficient could be determined from 400&apos; to 900°C. COEFFICIENTS of thermal expansion for hexagonal-close-packed (a) zirconium were determined up to 600°C (1112°F), without any interference from the effects of preferred orientation, by measurement of the lattice parameters obtained from a symmetrical back-reflection focusing X-ray camera. This paper combines the results for a 1.2 atomic pct hafnium alloy from an earlier report&apos; with those for hafnium-free zirconium. The problem confronting the investigator is essentially that of getting sharp, high-angle diffraction lines which represent the material at a known constanl. temperature and chemical composition. In order to do this, it was necessary to use the proper X-ray emission wave length (Co K was chosen) and to have a fine-grained metal whose atomic spacings would be free from effects of cold work (the specimen was annealed) and to prevent a changing composition owing to gas absorption during the heating of the metal to temperature (the sample was heated in a vacuum). A summary of the effect of temperature on properties is listed in Table I which gives data for ordinary zirconium, as well as new values for the low hafnium metal. The coefficients of the linear thermal expansion that have been reported are given in Table 11. The discrepancies shown may be explained perhaps by the effect of preferred orientation, and McGeary and Lustman2 have done this successfully for sheet metal. The differences in texture cannot explain all the differences in expansion coefficient shown in Table II. liesults by the author agree most closely with those of Kroll.3 Chemical analysis of the high hafnium metal pre- viously reported1 showed that it was 98.22 atomic pct (97.40 wt pct) pure. The low hafnium metal was dehydrogenated Westinghouse crystal bar, designated SMZ-137A. Its analysis was as given in Table 111 (chemical analyses 5377, 5431, and 5432).

Jan 1, 1955