Search Documents

By L. M. Barker, E. G. Lewis

THE literature of milling is replete with papers devoted to the subject of ball milling, all of which no doubt have contributed in one way or another to progress in that art. In this paper reference will be made to only a few of the many authors, but the value of the contributions of all who have written on that subject is hereby acknowledged. With a few exceptions the efforts of most students of the subject have been devoted to laboratory investigations of principles. Davis1 was one of the first to report on plant-scale investigations and to present to mill men certain criteria for the guidance of ball-milling practices. His conclusions with respect to the significance of sizing analyses of classifier sands in their relation to the factors of mill speed and ball sizing are particularly referred to. Those conclusions were: I. If the balls are large or the speed of the mill is high, crowding will appear at the finer sizes in the classifier sands. 2. If the balls are small or the speed is low, crowding will appear at the coarser sizes in the classifier sands. 3. The indications are that best efficiency is obtained when the screen analysis of the sands show a minimum crowding at any size. The last conclusion was qualified by the statement that it had not been proved conclusively. It is surprising, however, that the literature of later years reveals little evidence that millmen have made any serious attempt to apply those criteria. This may, perhaps, be explained by the fact that the average plant-scale ball-milling problem presents so many variables that an investigation of any one of them encounters the problem of control of the others-a problem that often is unsurmountable in a small plant. In a large plant, in which there is a duplication of grinding units in parallel operation, opportunity may be afforded for determining the value of such criteria. Nevertheless, a study of published data from grinding circuits of both large and small plants suggests that either Davis' criteria have been tried and found inapplicable or have never been given consideration. For the purpose of testing Davis' conclusions and with improvement of ballmilling efficiency as the final objective, a test program was initiated in the concentrator of the New Cornelia branch of the Phelps Dodge Corporation early in 1938. The practices of that plant have already been described.2 The fine-grinding units are arranged so that any one of eight units may be operated as a test unit and its results compared with those of the remaining units. All units receive similar feed from a common storage bin, in which the product of the fine-crushing plant is bedded by traveling tripper. The ball mills are all similar in size and operated at the same speeds, and are individually metered. The feeder conveyors of each unit are equipped with Merrick weightometers. The test program as initially outlined proposed investigation of the following:

Jan 1, 1941

By L. M. Barker, E. G. Lewis

THE literature of milling is replete with papers devoted to the subject of ball milling, all of which no doubt have contributed in one way or another to progress in that art. In this paper reference will be made to only a few of the many authors, but the value of the contributions of all who have written on that subject is hereby acknowledged. With a few exceptions the efforts of most students of the subject have been devoted to laboratory investigations of principles. Davis1 was one of the first to report on plant-scale investigations and to present to mill men certain criteria for the guidance of ball-milling practices. His conclusions with respect to the significance of sizing analyses of classifier sands in their relation to the factors of mill speed and ball sizing are particularly referred to. Those conclusions were: I. If the balls are large or the speed of the mill is high, crowding will appear at the finer sizes in the classifier sands. 2. If the balls are small or the speed is low, crowding will appear at the coarser sizes in the classifier sands. 3. The indications are that best efficiency is obtained when the screen analysis of the sands show a minimum crowding at any size. The last conclusion was qualified by the statement that it had not been proved conclusively. It is surprising, however, that the literature of later years reveals little evidence that millmen have made any serious attempt to apply those criteria. This may, perhaps, be explained by the fact that the average plant-scale ball-milling problem presents so many variables that an investigation of any one of them encounters the problem of control of the others-a problem that often is unsurmountable in a small plant. In a large plant, in which there is a duplication of grinding units in parallel operation, opportunity may be afforded for determining the value of such criteria. Nevertheless, a study of published data from grinding circuits of both large and small plants suggests that either Davis' criteria have been tried and found inapplicable or have never been given consideration. For the purpose of testing Davis' conclusions and with improvement of ball-milling efficiency as the final objective, a test program was initiated in the concentrator of the New Cornelia branch of the Phelps Dodge Corporation early in 1938. The practices of that plant have already been described .2 The fine-grinding units are arranged so that any one of eight units may be operated as a test unite and its results compared with those of the remaining units. All units receive similar feed from a common storage bin, in which the product of the fine-crushing plant is bedded by traveling tripper. The ball mills are all similar in size and operated at the same speeds, and are individually metered. The feeder conveyors of each unit are equipped with Merrick weightometers. The test program as initially outlined proposed investigation of the following:

Jan 1, 1941

By James Terry Duce

In order to facilitate interpretation of the data in this chapter, we print the following excerpts from the Circular to Authors. The field is the unit in this tabulation. In cases of fields extending across State boundaries, such as Rodessa, it is suggested that each State author treat the section of the field in his State as a unit, and by a footnote indicate that the field extends into an adjacent State. Each space in Table 1 may represent one of four possibilities; either it is not applicable to the particular field, or the proper entry is not determinable, or the proper entry may be determinable but is not determinable from data available to the author, or the proper entry is determinable. When spaces are not applicable, leave blank; in spaces where the proper entries are determinable from data available to the author, please insert y; in spaces where the proper entries are determinable by the author, make such entries. y implies a hope that in some future year a definite figure will be available. The entry of an 0 is a positive declaration, and an important declaration where it is in order. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries are not subject to precise determination. In such cases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces the correct entries represent the opinion of the author (for example, "Area Proved") and in such cases the entry need not be hedged to such extent as when the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use x. It is thought that the nearest whole numbers are sufficiently accurate for our purposes except as to percentage of sulphur in oil. If an author desires to report any other figures to tenths, he may do so. The quantity of gas produced should include, where possible, gas sold or otherwise marketed, and gas blown into the air, burned as flares or otherwise wasted. Segregation of these figures would be interesting if the authors can make such segregation. In any event, the figures should represent as nearly as possible the total quantity of gas removed from the reservoir. Under the columns on "Depth," the average depth to the top of the productive zones and to the bottom of the productive wells, when subtracted, should give the approximate thickness of the productive zone. For fields where this is not true

Jan 1, 1940

By James Terry Duce

In order to facilitate interpretation of the data in this chapter, we print the following excerpts from the Circular to Authors. The field is the unit in this tabulation. In cases of fields extending across State boundaries, such as Rodessa, it is suggested that each State author treat the section of the field in his State as a unit, and by a footnote indicate that the field extends into an adjacent State. Each space in Table 1 may represent one of four possibilities; either it is not applicable to the particular field, or the proper entry is not determinable, or the proper entry may be determinable but is not determinable from data available to the author, or the proper entry is determinable. When spaces are not applicable, leave blank; in spaces where the proper entries are determinable from data available to the author, please insert y; in spaces where the proper entries are determinable by the author, make such entries. y implies a hope that in some future year a definite figure will be available. The entry of an 0 is a positive declaration, and an important declaration where it is in order. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries are not subject to precise determination. In such cases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces the correct entries represent the opinion of the author (for example, "Area Proved") and in such cases the entry need not be hedged to such extent as when the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use x. It is thought that the nearest whole numbers are sufficiently accurate for our purposes except as to percentage of sulphur in oil. If an author desires to report any other figures to tenths, he may do so. The quantity of gas produced should include, where possible, gas sold or otherwise marketed, and gas blown into the air, burned as flares or otherwise wasted. Segregation of these figures would be interesting if the authors can make such segregation. In any event, the figures should represent as nearly as possible the total quantity of gas removed from the reservoir. Under the columns on "Depth," the average depth to the top of the productive zones and to the bottom of the productive wells, when subtracted, should give the approximate thickness of the productive zone. For fields where this is not true

Jan 1, 1940

By V. A. Zanadvoroff

The mine and concentrator of the Howe Sound Co., Chelan Division, are at Holden, in a remote section of the Cascade Mountains of northwestern Washington. Holden is at an elevation of 3200 ft., in the narrow valley of Railroad Creek. This creek drains into Lake Chelan, at a point some 40 miles up the lake from the town of Chelan. The concentrator treats 2000 to 2500 tons of low-grade copper-gold-zinc ore per day. Concentration is achieved by the differential flotation process, with recovery of 94 per cent copper and 82 per cent gold in the copper concentrate, followed by the recovery of 65 to 70 per cent zinc in the zinc flotation circuit. The final flotation tailing is deslimed, and coarse . sands, representing 60 to 70 percent of the total, are cyanided. The tonnage of tailing material amounts to 1900 to 2370 tons per day. General Considerations The property is within the Chelan National Forest. Railroad Creek is a fishing stream, being stocked regularly with trout from State hatcheries. Consequently, in planning a milling operation, the Howe Sound Co. was obliged to avoid any pollution of the stream by tailing material, and also destruction of valuable stands of timber. Moreover, the selected tailing- disposal sites should not mar the natural beauty of the valley. In addition to these requirements, the problem of tailing disposal at Holden was complicated by topography and climatic conditions. The valley is long and narrow, averaging 1200 to 1500 ft. in width. Its walls are flaring at a steep angle. There are no extensive flat areas suitable for deposition of tailing. All valleys tributary to Railroad Creek, also the well-marked paths of snowslides, must be avoided. Finally, the direction of prevailing winds and possible dust hazard arising therefrom dictated the necessity of selecting the tailing-disposal sites downstream from the mill building and two campsites. Heavy snowfall during the winter months of November to March, inclusive, impedes building of the retaining dike, making it necessary to prepare the needed storage space during the summer months. It is inadvisable, also, to do any dike building during the freezing weather, because the dike becomes unstable with the spring thaws, producing inevitable "sloughing" of the built-up borders. Tailing-disposal Sues The existing tailing-disposal areas are near the south wall of the valley. They were developed, and put to use in the following sequence: No. I. Area.—Covers approximately 10 acres. Built up to the height of 60 ft. and abandoned. Total length of dike border is 1900 feet.

Jan 1, 1947

By V. A. Zanadvoroff

The mine and concentrator of the Howe Sound Co., Chelan Division, are at Holden, in a remote section of the Cascade Mountains of northwestern Washington. Holden is at an elevation of 3200 ft., in the narrow valley of Railroad Creek. This creek drains into Lake Chelan, at a point some 40 miles up the lake from the town of Chelan. The concentrator treats 2000 to 2500 tons of low-grade copper-gold-zinc ore per day. Concentration is achieved by the differential flotation process, with recovery of 94 per cent copper and 82 per cent gold in the copper concentrate, followed by the recovery of 65 to 70 per cent zinc in the zinc flotation circuit. The final flotation tailing is deslimed, and coarse . sands, representing 60 to 70 percent of the total, are cyanided. The tonnage of tailing material amounts to 1900 to 2370 tons per day. General Considerations The property is within the Chelan National Forest. Railroad Creek is a fishing stream, being stocked regularly with trout from State hatcheries. Consequently, in planning a milling operation, the Howe Sound Co. was obliged to avoid any pollution of the stream by tailing material, and also destruction of valuable stands of timber. Moreover, the selected tailing- disposal sites should not mar the natural beauty of the valley. In addition to these requirements, the problem of tailing disposal at Holden was complicated by topography and climatic conditions. The valley is long and narrow, averaging 1200 to 1500 ft. in width. Its walls are flaring at a steep angle. There are no extensive flat areas suitable for deposition of tailing. All valleys tributary to Railroad Creek, also the well-marked paths of snowslides, must be avoided. Finally, the direction of prevailing winds and possible dust hazard arising therefrom dictated the necessity of selecting the tailing-disposal sites downstream from the mill building and two campsites. Heavy snowfall during the winter months of November to March, inclusive, impedes building of the retaining dike, making it necessary to prepare the needed storage space during the summer months. It is inadvisable, also, to do any dike building during the freezing weather, because the dike becomes unstable with the spring thaws, producing inevitable "sloughing" of the built-up borders. Tailing-disposal Sues The existing tailing-disposal areas are near the south wall of the valley. They were developed, and put to use in the following sequence: No. I. Area.—Covers approximately 10 acres. Built up to the height of 60 ft. and abandoned. Total length of dike border is 1900 feet.

Jan 1, 1947

By Charles Wright

AT most mines where large tonnages are handled, "bulldozing" or secondary blasting is an important and costly operation. To reduce the large blocks from primary blasting operations or stoping so that they will be small enough to pass through the chutes into the cars at the haulage level, and not too large for the crushing plant, requires blasting. Often this is done by placing a few sticks of dynamite on top of a block with or without a capping of mud, but to consume less dynamite and to promote safety, most secondary blasting is now done by blockholing, or the drilling of holes 6 to 12 in. long in the blocks, using only a part of a stick of dynamite per hole. Regardless of the method of blasting, however, the term "bulldozing chamber" is applied to the room where this work is done. Bulldozing chambers permit secondary blasting at all times in a safe place without disturbance to the other mining operations. The chambers are usually high above the haulage level and well below the stope level or open-pit floor. In most instances the material is passed through a grizzly in the bulldozing chamber, but sometimes no grizzlies are used. One to four raises extend from the chamber to the stope floor and one or two from the haulage level to the chamber floor. Occasionally large slabs of ore or rock choke the raises above the bull-dozing chamber, and these have to be blasted by attaching a bundle of dynamite sticks on the end of a long pole and placing them up in the raise between the pieces causing the choke. This is called "chute-blasting." To give a picture of the progressive developments in the use of the bulldozing chamber, a few typical mines that show the application of this method to both metal and limestone mines have been selected for description here. Limestone mines have been included because many metal miners do not realize to what extent the nonmetallic, or rock, miners are now applying metal-mining methods successfully in their operations. The bulldozing chamber is the "neck of the bottle" for some mines.

Jan 1, 1935

By E.G. Lewis, l.M. Barker

The literature of milling is replete with papers devoted to the subject of ball milling, all of which no doubt have contributed in one way or another to progress in that art. In this paper reference will be made to only a few of the many authors, but the value of the contributions of all who have written on that subject is hereby acknowledged. With a few exceptions the efforts of most students of the subject have been devoted to laboratory investigations of principles. Davis1 was one of the first to report on plant-scale investigations and to present to mill men certain criteria for the guidance of ball-milling practices. His conclusions with respect to the significance of sizing analyses of classifier sands in their relation to the factors of mill speed and ball sizing are particularly referred to. Those conclusions were: 1. If the balls are large or the speed of the mill is high, crowding will appear at the finer sizes in the classifier sands. 2. If the balls are small or the speed is low, crowding will appear at the coarser sizes in the classifier sands. 3. The indications are that best efficiency is obtained when the screen analysis of the sands show a minimum crowding at any size. The last conclusion was qualified by the statement that it had not been proved conclusively. It is surprising, however, that the litera- ture of later years reveals little evidence that millmen have made any serious attempt to apply those criteria. This may, perhaps, be explained by the fact that the average plant-scale ball-milling problem presents so many variables that an investigation of any one of them encounters the problem of control of the others—a problem that often is unsurmountable in a small plant. In a large plant, in which there is a duplication of grinding units in parallel operation, opportunity may be afforded for determining the value of such criteria. Nevertheless, a study of published data from grinding circuits of both large and small plants suggests that either Davis' criteria have been tried and found inapplicable or have never been given consideration. For the purpose of testing Davis' conclusions and with improvement of ball-milling efficiency as the final objective, a test program was initiated in the concentrator of the New Cornelia branch of the Phelps Dodge Corporation early in 1938. The practices of that plant have already been described.2 The fine-grinding units are arranged so that any one of eight units may be operated as a test unit and its results compared with those of the remaining units. All units receive similar feed from a common storage bin, in which the product of the fine-crushing plant is bedded by traveling tripper. The ball mills are all similar in size and operated at the same speeds, and are individually metered. The feeder conveyors of each unit are equipped with Merrick weightometers. The test program as initially outlined proposed investigation of the following:

Jan 1, 1943

By L. M. Barker, E. G. Lewis

The literature of milling is replete with papers devoted to the subject of ball milling, all of which no doubt have contributed in one way or another to progress in that art. In this paper reference will be made to only a few of the many authors, but the value of the contributions of all who have written on that subject is hereby acknowledged. With a few exceptions the efforts of most students of the subject have been devoted to laboratory investigations of principles. Davis1 was one of the first to report on plant-scale investigations and to present to mill men certain criteria for the guidance of ball-milling practices. His conclusions with respect to the significance of sizing analyses of classifier sands in their relation to the factors of mill speed and ball sizing are particularly referred to. Those conclusions were: 1. If the balls are large or the speed of the mill is high, crowding will appear at the finer sizes in the classifier sands. 2. If the balls are small or the speed is low, crowding will appear at the coarser sizes in the classifier sands. 3. The indications are that best efficiency is obtained when the screen analysis of the sands show a minimum crowding at any size. The last conclusion was qualified by the statement that it had not been proved conclusively. It is surprising, however, that the litera- ture of later years reveals little evidence that millmen have made any serious attempt to apply those criteria. This may, perhaps, be explained by the fact that the average plant-scale ball-milling problem presents so many variables that an investigation of any one of them encounters the problem of control of the others—a problem that often is unsurmountable in a small plant. In a large plant, in which there is a duplication of grinding units in parallel operation, opportunity may be afforded for determining the value of such criteria. Nevertheless, a study of published data from grinding circuits of both large and small plants suggests that either Davis' criteria have been tried and found inapplicable or have never been given consideration. For the purpose of testing Davis' conclusions and with improvement of ball-milling efficiency as the final objective, a test program was initiated in the concentrator of the New Cornelia branch of the Phelps Dodge Corporation early in 1938. The practices of that plant have already been described.2 The fine-grinding units are arranged so that any one of eight units may be operated as a test unit and its results compared with those of the remaining units. All units receive similar feed from a common storage bin, in which the product of the fine-crushing plant is bedded by traveling tripper. The ball mills are all similar in size and operated at the same speeds, and are individually metered. The feeder conveyors of each unit are equipped with Merrick weightometers. The test program as initially outlined proposed investigation of the following:

Jan 1, 1943

The Wheeler Condenser & Engineering Co., of Carteret, N. J., is now building a line of horizontal and vertical shaft centrifugal pumps for general services, as well as for condenser work.. This company has been building centrifugal pumps for over 20 years, most of them being used, however, in connection with condensers. The new line of pumps is suited for all services. A small motor-driven unit for tank or stand pipe operation is shown in Fig. 1. Referring to the sectional illustration (Fig. 2), it will be seen that this pump conforms to the most recent advances in centrifugal pump construction, having a two-part divided casing, with the suction and discharge nozzles in the lower half. The impeller is of the closed double-suction type, protected by labyrinth wearing rings. The shaft is protected from the water by bronze sleeves, which screw on to the shaft and extend clear through into the bearing bracket boxes. Bearings are of the ring-oiled type, and in the outboard bracket, is a ring-oiled thrust bearing, which is a refinement not usually found in double-suction

Jan 4, 1916

By P. H. Turnock, R. D. Pehlke

The effects of mutual interactions between elements on the solubility of nitrogen in liquid iron alloys containing chrormium, columbium, molybdenurn, nickel, or silicon have been determined. The equilibrium nitrogen solubilities in the liquid iron alloys were measured by the Sieverts method. The second-order effects caused by the presence of chrormium, columbium , or silicon in the melt were found to be significant. The solubility of nitrogen in liquid iron alloys containing several alloying elements has also been measured as a function of melt temperature and nitrogen pressure. The heat of solution of nitrogen in microcomponent iron alloys has been found to be a function of the logarithnz of the activity coefficient of nitrogen, irrvespectilje of the composition of the melt. The heat of solution of nitrogen in pure liquid iron was determined to be 1265 ± 450 cal per g-atom of N over the temperatxue range 1600° to 1800°. Sieverts ' law was obeyed for all melt compositions studied in the pressure interval 0.4 to 1.0 atm. The solubility of nitrogen in liquid pure iron and in many dilute binary liquid-iron alloys has been the subject of many investigations. Pehlke and Elliott' made a comprehensive investigation on this subject in which they summarized and compared previous researches. However, the practical application of these solubility studies requires prediction of the nitrogen solubility in the multicomponent alloys encountered in operating practice. The interaction parameter as defined by wagner2 has been used to predict the behavior of a solute in a complex alloy, and a modification of this approach has met with reasonable success in several instances.'1"5 The necessity for extending the nitrogen solubility data on binary alloys is caused by the lack of direct measurements of the solubility of nitrogen in molten alloy steels. A direct comparison between measured solubilities and those predicted for multicomponent alloys based on data in binary systems has been made in only a few instances, and most of these were reviewed by Langenberg,6 who developed a graphical technique for predicting nitrogen solubilities in multicomponent iron alloys. The solubility of nitrogen has also been studied over the entire Fe-Cr-Ni ternary system by Humbert and Elliott.? Both studies compared the solubilities computed from binary iron alloy data with those measured in ternary alloys in the liquid state at 1600°C. Most of the nitrogen solubility measurements referred to above were for iron alloys at 1600°C; thus, the ability to predict nitrogen solubilities in molten iron alloys has been restricted primarily to alloys at 1600°C. Recently, Nelsson8 devised an approximate method for calculating the change in nitrogen solubility in molten iron alloys as a function of temperature, but an assumption of regular solution behavior limits the applicability of the method. Chipman and Corrigan9,10 have developed an empirical correlation. based on the activity coefficient of nitrogen in the iron alloy at 1600°C, which facilitates the estimation of nitrogen solubilities at higher temperatures. This method also has limitations, due to the necessity of calculating the activity coefficient for nitrogen in a multicomponent iron alloy at 1600°C from the nitrogen solubility data for binary iron alloys. The shortcoming of such a straightforward approach to the problem of predicting nitrogen solubilities is the disregard of mutual interactions between elements in a complex iron melt. This investigation was conducted in an attempt to provide a more reliable method of predicting nitrogen solubilities in multicomponent iron alloys. The effects of the mutual interactions between chromium, nickel, silicon, molybdenum, or columbium in iron were studied, using the Sieverts' technique1,7 to measure the effects of alloy composition, temperature, and pressure on the solubility of nitrogen in ternary liquid iron alloys.

Jan 1, 1967

Jan 1, 1899

By Jesse Betterton

IN the Parkes process of lead refining, after desilverization has been completed by means of zinc additions, there will remain in the lead from 0.5 to 0.6 per cent zinc. At this stage in the refining practically all impurities are reduced to refined lead specifications except zinc and antimony. All excess of copper and nearly all the arsenic goes out with the silver. Silver remaining should not exceed 0.1 oz. per ton. It thus remains only to remove zinc and antimony to produce refined lead. The older practice was to complete refining by means of oxidation processes in reverberatory furnaces. Essentially this consisted of heating the lead to 1200° to 1300° F. and allowing it to come in contact with a considerable excess of air passing through the furnace, or accom-plish the same result by blowing the lead with steam by means of pipes introduced for that purpose, at the same time allowing air to enter the furnace. Usually some procedure involving alternate oxidation and reduction with fine coal or coke was employed in order to reduce the weight of dross or skim finally removed from the furnace. This practice had many elements of weakness in that the main flow of lead, after the preceding expensive operations had been performed, and the whole refining process nearly completed, was subjected to an operation at a comparatively high temperature, which involved much lead loss if the furnaces were not on bags, and the production of 3 to 5 per cent of the weight of the lead as dross or skim, which had to be resmelted and the lead either refined or produced as antimonial lead. In addition, the operating expense of the process was a considerable item. The, process of dezincing with chlorine was developed as a substitute for the foregoing described oxidation process, and finally resulted in such advantages as nearly equal operating costs, a practical elimination of the lead loss, and the direct production of a very valuable byproduct, zinc chloride, that may be sold as such or retreated for its zinc and chlorine contents, both of which can be reused in the refining processes.

Jan 1, 1933

By F. Paredes, W. R. Holman, R. W. Crawford

The diffusion coefficient for hydrogen in the ß titanium alloy containing 13 pct V, 11 pct CY, and 3 pct A1 was measured over the temperature range 20° to 500°C. Results fit the expression: D= 1.58 x lgs exp-------==-----) cm2,sec THE diffusion coefficient for hydrogen in the metastable ß-phase titanium alloy containing 13 pct V, 11 pct Cr, and 3 pct A1 was measured as part of an investigation of the effects of hydrogen on the mechanical properties of titanium alloys. Several theories on the mechanisms of hydrogen embrittle-ment include diffusion of hydrogen at ambient temperature as an important step in the embrittling process.'-5 In hydrogen-contaminated a-ß titanium alloys, it has been postulated that the rate-controlling step may be the rate at which hydrogen diffuses from the ß phase to stress- or strain-nucleated brittle hydride platelets at the a-ß interface.' However, embrittlement of the all-ß alloy investigated in this work may proceed by a different mechanism, since this alloy can be embrittled without the formation of detectable hydride platelets.6 Troiano has suggested that in this case the mechanism of delayed failure or embrittlement is similar to that proposed for high-strength steel, i.e., repeated crack initiation caused by a decrease in bonding energy as hydrogen diffuses to points of high tri-axial stress at the root of a notch. In both types of alloy the rate of embrittlement is believed to be controlled by diffusion of hydrogen in the ß phase. Accurate hydrogen-diffusion data in the vicinity of room temperature should therefore be of some assistance in understanding the mechanisms of embrittlement in these two classes of titanium alloys. Diffusion of hydrogen in pure titanium has been studied by Wasilewski and Kehl7 at temperatures above 500°C. Their measurements on diffusion in the ß phase were extended below the ß-a transformation temperature (882°C) to approximately 600°C. This was possible because of the 8 stabilizing effect of hydrogen. No results at lower temperatures have been published and there are no data in the literature on hydrogen diffusion in the ß -phase alloy used in this program. Hydrogen diffusion in metals is generally investigated by measuring the rate of transport of hydrogen past a solid-gas interface, i.e., by absorption, permeation, or degassing-rate measurements. These methods produce accurate diffusion data when bulk diffusion is the rate-determining step in the over-all process. However, at the lower temperatures of interest in hydrogen-embrittlement studies or under conditions where surface films are present, the measured rates may be surface-controlled and the calculated diffusion coefficients will be in error. Surface effects were eliminated in the present work by using a modification of the common welded-couple technique m which two bars with uniform but different compositions are joined before the diffusion anneal." The same type of step change in the initial concentration vs distance curve was produced by electrolytically hydrogenating thin-strip specimens which had been electrically insulated over half of their length. Concentration vs distance curves were determined, after appropriate diffusion-annealing treatments, by vacuum-extraction analyses of transverse samples sheared from the strips. Diffusion coefficients were calculated by the methods of Grube.M This technique was feasible because of the large concentrations of hydrogen which can be charged into p -phase alloys without the formation of hydrides15'16 and because of the extremely low degassing rates observed when hydrogenated titanium alloys are heated in air. EXPERIMENTAL WORK The diffusion couples were cut from a 0.022-in.-thick mi ll-annealed sheet.* Strips 8 in. long by 1/2

Jan 1, 1965

By A. E. Jenkins, L. A. Baker, N. A. Warner

The electromagnetic levitation technique has been successfully applied to rate studies of the de-carburization of liquid Fe-C alloys from 5.5 to zero pct C at 1660°C using gas mixtures containing 1 to 100 pct CO2 with CO or helium as diluents. The rate was shown to be independent of carbon concen -tration in the melt and only slightly affected by total pressure. The results were shown to be consistent with control either wholly or predominantly by gaseous diffusion. As well as avoiding side reactions with the crucible, levitation allowed precise calculation of reaction rates since the geometry of the system was accurately known. It also enabled interpretation using the established mass-transfer correlations for a gas flowing past a single sphere, The existence of gaseous-diffusion control and the extremely high rates of reaction reported for gas flowing past small spheres are of great practical significance in relation to current investigations into the use of spray-refining techniques in continzcous steelmaking. PREVIOUS work on the kinetics of carbon removal from liquid iron has generally involved the use of oxygen as the gaseous oxidant. Investigations have been made on commercial steelmaking furnaces and in addition laboratory-scale experiments have been attempted with a slag phase present. The general lack of agreement and the obvious difficulty in interpreting the results is at least partly due to the complexity of the systems used. This work has been reviewed by carter1 and more recently by Bods-worth2 and ward.3 The gas-liquid metal reactions have also been studied with slag-free melts by the conventional technique of blowing oxygen onto the melt contained in a crucible. The reaction between the oxidant and carbon could be followed by sampling either the melt or the gas phase. Side reactions with the crucible material have precluded direct interpretation of the results. Fujii, 5-7 using O-A mixtures, attempted to correct for the crucible reaction and reported that the reaction between carban and oxygen occurred at the melt surface and was controlled by gaseous diffusion for carbon contents greater than a critical value and by carbon-diffusion control in the metal for carbon contents less than the critical. The critical value was given as approximately 0.15 pct C. However, whereas this was the case for oxygen contents in the gas stream up to 10 pct, between 10 and 20 pct the rate was found to be approximately independent of oxygen content, and Fujii attempted to explain this observation by postulating the presence of an oxide "film".7 Turkdogan et a1.' have studied iron fuming during decarburizing and suggested gaseous-diffusion control of the reaction above a critical carbon concentration, given as approximately 2 pct C. Filippov9-12 reports in a similar manner to Fujii but makes no mention of the crucible reaction with the carbon in the melt, even though this would be expected with the temperature, crucible material (MgO), and carbon contents used. Both CO2 and O2 were used as oxidant gases. In the present work the decarburization of liquid Fe-C alloys was studied using an adaptation of the electromagnetic levitation technique, and thus the complexities introduced by crucible side reactions were eliminated. In this technique a single sphere of the Fe-C alloy is freely suspended and heated by electromagnetic induction in a flowing stream containing the oxidant gas. The full range of carbon levels up to saturation was studied, the temperature of the melts in this instance being held constant at 1660°C. The oxidant was CO2 which was used either pure or in association with a diluent gas, the total gas pressure being maintained either at 1 atm or at a reduced pressure. Thus the reaction under study was:

Jan 1, 1964

By Charles W. Wright

At most mines where large tonnages are handled, "bulldozing" or secondary blasting is an important and costly operation. To reduce the large blocks from primary blasting operations or stoping so that they will be small enough to pass through the chutes into the cars at the haulage level, and not too large for the crushing plant, requires blasting. Often this is done by placing a few sticks of dynamite on top of a block with or without a capping of mud, but to consume less dynamite and to promote safety, most secondary blasting is now done by blockholing, or the drilling of holes 6 to 12 in. long in the blocks, using only a part of a stick of dynamite per hole. Regardless of the method of blasting, however, the term "bulldozing chamber" is applied to the room where this work is done. Bulldozing chambers permit secondary blasting at all times in a safe place without disturbance to the other mining operations. The chambers are usually high above the haulage level and well below the stope level or open-pit floor. In most instances the material is passed through a grizzly in the bulldozing chamber, but sometimes no grizzlies are used. One to four raises extend from the chamber to the stope floor and one or two from the haulage level to the chamber floor. Occasionally large slabs of ore or rock choke the raises above the bulldozing chamber, and these have to be blasted by attaching a bundle of dynamite sticks on the end of a long pole and placing them up in the raise between the pieces causing the choke. This is called "chute-blasting." To give a picture of the progressive developments in the use of the bulldozing chamber, a few typical mines that show the application of this method to both metal and limestone mines have been selected for description here. Limestone mines have been included because many metal miners do not realize to what extent the nonmetallic, or rock, miners' are now applying metal-mining methods successfully in their operations. The bulldozing chamber is the "neck of the bottle" for some mines.

Jan 1, 1937

By A. J. Stosick, J. R. Hoffman, E. Rudy, St. Windisch

The binary alloy system Mo-C zoas investigated by means of X-ray, metallog/aphic, thermoanalytical, and melting-point techniques on chemically analyzed specimens. The system, Fig. 39, is characterized by three congruently melting, intermediate phases, Mo2C, n MoCi-x, and aMoC1-,, of which only Mo,C is stable at temperatures below 1650°C. Substoichio-metrzc (~32.5 at. pct C) dimolybdenum carbide undergoes a homogeneous sublattice order-disorder transformation at temperatures of approximately 1400°C, whereas hyperstoichiorrletric compositions undergo a discontinuous Phase change. The order-disorder transitions in the Me, C phases are discussed in terms of the structural changes involved in the transformation processes and the absence of long-range sublattice coherency in stoichiometric or hyperstoiclziomet-ric compositions attributed to the impossibility of obtaining long-range order in a linear chain of alternating carbon atoms and vacancies. From the experimental phase relutionships and the known thermody-namic data for Mo2 C, limits for the free energies of formation for the high-temperature phases r) MoC1-, and aMoC1-, are deriued and found to be in good agreement with data previously obtained from phase equilibria in ternary metal-carbon systems. IN the course of studies of the high-temperature phase relationships in ternary systems of refractory transition metals with carbon,' a number of inconsistencies found in previous work necessitated a reex-amination of some of the related metal-carbon binaries. A reassessment of the binary system data also seemed

Jan 1, 1968

By E. R. Palowitch, P. H. Broussard

The United States aims to achieve some modicum of energy self-sufficiency through means such as conservation, increased domestic oil and gas production, substitution by the electric utilities of coal or coaloil mixtures for oil and gas, and development of a viable synthetic liquid fuels industry. Coal's role in attaining this goal will necessitate doubling coal production by the end of the 1980's. And if the United States does in fact become the World's Saudi Arabia of coal, the total annual production to meet these domestic needs and export markets could double again by the year 2,000. As only a small portion of our Nation's reserves are recoverable by state-of-the-art surface mining methods, most of the coal produced in the future will have to be mined underground (Averitt, 1975). But this projected increase in coal demand is occurring in the face of a decade of radically decreasing productivity. Specifically, average worker productivity in underground coal mines has decreased from 14.2 tonnes (metric tons) per workershift in 1969 to 7.2 tonnes per worker-shift in 1979; and 95 percent of coal produced underground during this period was produced by room-and-pillar methods (U.S. Dept. of Energy, 1980). Although there is no complete agreement on the impact of recent Federal legislation, there is strong correlation between the dramatic decrease in productivity in underground coal mining and the implementation of the recent Federal mine health and safety regulations (U.S. Congress, 1969). A review of the wide range of coal mining research, development, and demonstration projects currently being funded by the federal government and by industry gives little encouragement for increasing worker productivity on room-and-pillar sections underground in the immediate future (Palowitch, 1978). Conversely, the opportunities for increasing production/productivity underground with longwall methods appear somewhat more encouraging. Although at least one longwall face in the U.S. did produce more than one million tonnes of coal in a single year, the national two-shift average production from one hundred or so longwall faces is about 1,000 tonnes per day (Huwood-Irwin Co., 1978 and Consolidation Coal Company, 1976). Clearly, there exists some real opportunities for improvement. One of these opportunities is to automate the cutter-loader.

Jan 1, 1981

By J. Chipman, T. Fuwa

The effects of various elements on the activity coefficient of carbon in liquid iron have been studied by two experimental methods: 1) equilibration with controlled mixtures of CO and CO2; 2) the solubility of graphite in the melt. Activity coefficient of C is increased by Al, Co, Cu, Ni, P, Si, S, and Srz. It is decreased by Cr, Cb, Mn, Mo, W, and V. THE thermodynamic properties of the iron-carbon binary system have now been fairly well established, although some uncertainty remains with respect to the exact location of some of the phase boundaries. The activity of carbon in ferrite and in austenite has been measured in the classic researches of R. P. smith' while similar measurements by Richardson and ~ennis, and by Rist and chipman3 have established the values of the activity of carbon in liquid iron up to 1760°C. On the other hand, our knowledge of the effects of alloying elements on the activity of carbon in dilute solutions is restricted to Smith's experiments on systems Fe-C-Mn and Fe-C-Si in the austenitic range and to some more recent experiments of schwarzman4 in the a range. In addition there have been a number of determinations of the effects of various elements on the solubility of graphite in liquid iron, and from these the corresponding effect in saturated solution may be obtained. The purpose of the present study was to extend the investigation of the liquid system to include the effects of alloying elements upon the activity coefficient of carbon, principally in dilute solutions. Equilibrium measurements were made on the reaction C + co, = 2 CO (g) The prepared mixture of CO and CO,, diluted with argon, flowed over the surface of the liquid metal which, after several hours' exposure to the gas, was quenched and anqlyzed. As in the earlier experiments, the principal experimental difficulty was in the deposition of carbon on the parts of the furnace at temperatures slightly below that of the metal bath. In order to minimize this difficulty, the ratio (Pco)2 /PCo2 was restricted to values not much higher than 100 atm, and correspondingly the carbon concentration in the metal seldom exceeded 0.30 pct. EXPERIMENTAL METHODS The method and apparatus were essentially the same as used by Rist and Chipman.3 The gaseous mixture consisting of highly purified CO, CO,, and argon, each controlled by a flowmeter, was led into the furnace and passed over the surface of the liquid-iron melt which was heated and stirred by high-frequency induction. One slight modification was made in that a molybdenum susceptor was placed outside the crucible for the sake of uniformity of temperature and to combat the tendency of carbon to precipitate on the crucible wall. Pure alumina crucibles approximately 25 mm ID were used. The charge consisting of about 30 g was made up of electrolytic iron, the alloying element to be added, and enough graphite to supply slightly more or less than the anticipated equilibrium carbon concentration. All metals used were of high purity. Metallic chromium, columbium, and vanadium were from special lots supplied by the Electro Metallurgical Co. Tin, copper, molybdenum, tungsten, cobalt, and nickel were of purest commercial grades. The electrolytic iron, after being cut to the proper size for charging, was prereduced by hydrogen at 850° to 1000°C to remove surface oxidation. The oxygen content of the reduced material was 0.002 pct. This treatment made it easy to control the carbon content of the initial melt. The charge was melted under the gas mixture to be used for the entire run. In some earlier melts the charge was melted under a stream of argon, but in this case some alumina was reduced from the crucible, and the aluminum thus absorbed in the melt was subsequently oxidized with the formation of a solid film of alumina on the surface of the melt. AS another safeguard against film formation, overheating of the bath was carefully avoided. All runs were made at a temperature of 1560°C. Under experimental conditions a charge of pure iron picked up 0.17 pct C in 3 hr and 0.23 pct C in 6 hr under an atmosphere for which the equilibrium concentration of carbon is 0.27. It is clear that the time required to reach equilibrium from an initially carbon-free melt would be very great. For this reason each experiment was started with a melt of known carbon concentration not far above or below the expected equilibrium value, and each melt was held at temperature for a period of at least 5 hr. Under such circumstances it was possible to chart the approach to equilibrium from both high-carbon and low-carbon materials. Temperature was controlled by frequent optical observation and adjustment and the metls were timed in such a way that the final 2 hr occurred during a time when electric power was steady; for example, 2 to 4 pm or after 11 pm. In melts containine volatile metals such as copper, tin, and mangane\e the time of holding was decreased somewhat in

Jan 1, 1960

By H. B. Pulsifer

The unprecedented high price of zinc ore prevailing through the early months of 1915 caused great activity in the Joplin district of Missouri. The Media mill is conspicuous as one of the first of the new "big mills" of the district. The mill was built over a mine previously worked but abandoned in 1912 because of the leanness of the ore and the large quantity of water encountered. The ore prices prevailing—$100 a ton in June, 1915, as against $50 in 1912-—favored the new undertaking. The mill was designed for good recovery so that it might operate in times of depression. In design and equipment, the mill is exclusively local in conception and construction. Former Exploitation The tract of land is a part of the large Guinn holdings; 70 acres are comprised in this particular lot, which is situated just a mile north of the center of Webb City on the Alba line of the Southwest Missouri Electric Railway. The ore lies 242 ft. below the surface at the top of the knoll which is surrounded by the well known properties: Black Cat, Ground Floor, Florence, Hurry-Up, Electrical, and Mercantile. Since the abandonment, in 1913, of the Yellow Dog a bit farther to the north, the Black Cat, Ground Floor, and Florence workings had been flooded. However, as there was no cut through from this side into the area it was proposed to exploit, it was thought that moderate pumping facilities would take care of the water. Three shafts had already been sunk to the ore horizon during the previous operations; the ground was connected by wide drifts and possibly 10 acres mined out, principally about the two southerly shafts which at surface are 8 and 13 ft. lower, respectively, than the collar of the shaft at which the new mill was built. The former mill on the lease was known as the Bohemian Girl. This mill, built in 1910, was removed after some 3 years' work. A head frame and hopper still existed at the middle shaft, sometimes known as the lower Hold Out shaft, but at the most northerly

Jan 1, 1918