Search Documents

By W. A. Ver Wiebe

The year 1939 in Kansas, with a production of 57,944,300 bbl. from 19,669 wells, shows a slight recession from the peak of oil production reached the previous year, when slightly over 59,000,000 bbl. of oil was marketed. The previous peak had been reached in 1917 with 45,451,000 bbl. marketed. Another still earlier peak had been reached in 1904, when slightly less than 5,000,000 bbl. was produced and sold. The production of gas probably reached a new peak during 1939 with a total of over 69 billion cubic feet. Between the peak of the year 1908, when over 80 billion cu. ft. was produced, and that of 1939 the production dropped to 16 billion cu. ft., in the year 1921. During the year 1458 wells were drilled. This figure is somewhat lower than that given in several trade journals, because it does not include wells that were deepened or recompleted in a different geological horizon. Nearly 75 per cent (1029) of the total number of wells were completed as commercial oil wells (824 in western and 205 in eastern Kansas). The commercial gas wells completed number 71, of which 24 are in eastern Kansas and 47 in western Kansas. The remaining completions include 154 dry holes in eastern and 204 dry holes in western Kansas. Based on daily potential capacity the new discoveries of the year accounted for a cumulative initial production of 264,000 bbl. in eastern and 1,158,827 bbl. in western Kansas. It is interesting in this connection to note that the number of wells completed in the state rose gradually to a first peak in 1904, when 2782 were drilled. The number dropped off rapidly to 368 three years later, but rose to the second and highest peak in 1918, when 4671 wells were completed. In the period between 1904 and 1912 more gas wells than oil wells were completed. Between the high peak of 1918 and the somewhat lower peak of 1937, the low point was reached during 1931 with the completion of only 470 wells. In the matter of new pools discovered, Kansas again ranks high. The exact number depends somewhat upon the interpretation of a "new" area—whether it should be called a new pool or a long extension of an older pool. In some places this determination cannot be made until more wells are drilled within the area. Therefore, the figures given

Jan 1, 1940

By W. A. Ver Wiebe

The year 1939 in Kansas, with a production of 57,944,300 bbl. from 19,669 wells, shows a slight recession from the peak of oil production reached the previous year, when slightly over 59,000,000 bbl. of oil was marketed. The previous peak had been reached in 1917 with 45,451,000 bbl. marketed. Another still earlier peak had been reached in 1904, when slightly less than 5,000,000 bbl. was produced and sold. The production of gas probably reached a new peak during 1939 with a total of over 69 billion cubic feet. Between the peak of the year 1908, when over 80 billion cu. ft. was produced, and that of 1939 the production dropped to 16 billion cu. ft., in the year 1921. During the year 1458 wells were drilled. This figure is somewhat lower than that given in several trade journals, because it does not include wells that were deepened or recompleted in a different geological horizon. Nearly 75 per cent (1029) of the total number of wells were completed as commercial oil wells (824 in western and 205 in eastern Kansas). The commercial gas wells completed number 71, of which 24 are in eastern Kansas and 47 in western Kansas. The remaining completions include 154 dry holes in eastern and 204 dry holes in western Kansas. Based on daily potential capacity the new discoveries of the year accounted for a cumulative initial production of 264,000 bbl. in eastern and 1,158,827 bbl. in western Kansas. It is interesting in this connection to note that the number of wells completed in the state rose gradually to a first peak in 1904, when 2782 were drilled. The number dropped off rapidly to 368 three years later, but rose to the second and highest peak in 1918, when 4671 wells were completed. In the period between 1904 and 1912 more gas wells than oil wells were completed. Between the high peak of 1918 and the somewhat lower peak of 1937, the low point was reached during 1931 with the completion of only 470 wells. In the matter of new pools discovered, Kansas again ranks high. The exact number depends somewhat upon the interpretation of a "new" area—whether it should be called a new pool or a long extension of an older pool. In some places this determination cannot be made until more wells are drilled within the area. Therefore, the figures given

Jan 1, 1940

ENGINEERS AVAILABLE. (Under this heading will be published notes sent to the Secretary of the Institute by members or other persons.) Member, graduate of College of Mines of University of California, with 12 years' operating experience in mining and milling in California, Canada, and Mexico, is open for engagement. Speaks Spanish fluently. No. 17. Mining engineer and metallurgist open for engagement Jan. 1 as superintendent of mines or constructing engineer. Technically educated, with 14 years' experience in United States and Latin America in concentration, amalgamation, cyaniding, constructing. At present building large modern .all-sliming cyanide mill in Central America. No. 18. Member, mining and metallurgical engineer, is open to engagement. Specialty, the treatment of copper ores. Nine years' experience in the operation and also in the design and erection of copper smelteries. Four years true pyrite smelting. Able to organize the administration, accounting, etc., of a large plant. Speaks a fair amount of Spanish, Russian, German, and French. Qualified to take charge of a large smeltery, or to act as assistant to manager of a combined mining and smelting concern. No. 19. Member, technical graduate, 33 years old, 11 years' experience as chemist, metallurgist, and superintendent of lixiviation plant and in charge of construction of cyanide mill, is open for engagement. Speaks Spanish. No. 21. Member, lately with the Bishop Creek Milling Co., California, is now open for engagement as mine superintendent or superintendent of construction of mine and mill structures. No. 25.

Jan 12, 1913

By J. E. Burke

THE origin of recrystallization textures continues to be a matter of controversy. One explanation is that a recrystallization texture occurs because only grains having a limited range of orientations ever appear in the deformed matrix—the oriented nuclea-tion* hypothesis. Another explanation is that grains essentially having all orientations are nucleated but that those having certain orientations grow much more rapidly than any others in the deformation texture, and thus only the rapidly growing grains survive when recrystallization is complete. There has recently appeared a great deal of evidence'- indicate that recrystallized grains of face-centered cubic metals are frequently related to their parent grains by rotations of 20" to 40" about a common [lll] direction. Furthermore, it has been observed that the growth rate of the new grains depends upon their orientations with respect to the matrix, and that the most rapidly growing grains lie within the stated range of orientations. In a recent note, Beck7 has concluded from observations of this type that oriented growth alone is responsible for the appearance of preferred orientations in re-crystallized metals. It should be pointed out. however, that many of the available data indicate that oriented nucleation operates in addition to oriented growth. Thus, while oriented growth may permit a selection to be made among nuclei of several orientations, only a limited number of orientations are available in the first place for such selection.

Jan 1, 1953

SEC. 1. The membership of the Institute shall comprise six classes, namely: 1. Members; 2. Honorary Members; 3. Senior Members; 4. Associates; 5. Junior Members; 6, Rocky Mountain Members. All shall be equally entitled to the privileges of membership, excepting that no member of any class whose residence shall be outside of the United States of America, except those residing in Mexico and Canada, shall be entitled to vote. SEC. 2. Members: A person to be eligible for election or transfer into the class of Member must be at least 27 years of age and must have had at least six years' employment in the practice of engineering, mining, geology, metallurgy, or chemistry, during at least three years of which he must have held positions of responsibility in one or more of these fields. This shall not apply to Rocky Mountain members. SEC. 3. Honorary Members: Each candidate for Honorary Membership must be recommended by at least ten Members and must be elected by ballot at a meeting of the Board of Directors by the unanimous vote of the Directors present; provided, however, that the number of Honorary Members shall at no time exceed twenty. Such election shall automatically act as a transfer of such member from any other class of membership to which he may belong. SEC. 4. Senior Members: The Directors may in their discretion place on the Honor Roll of Senior Members and transfer from any other class of membership other than Honorary Membership the name of any Member or Associate who has reached the age of seventy years and who has paid dues for thirty years, and for good reasons in • special cases may vary the age or number of years. SEC. 5. Junior Members: A person to be eligible for election to the class of Junior Member must be qualified through education or experience to hold a subordinate position in engineering, mining, metallurgical, geological or chemical work. He shall be not more than twenty-seven years of age at the time of election. The rights of the present Junior Associates shall continue until the same expire by limitation of time. SEC. 6. Associates: A person eligible for election or transfer into the class of Associate shall be one, who, in the opinion of the Committee on Admissions and the Board of Directors, is suitable for such election or transfer by reason of his interest in or connection with mining, geology, metallurgy, or chemistry. SEC. 7. Rocky Mountain Members: Membership in a special class of life memberships without annual or other dues and without right to receive the printed literature distributed to other members or the right and privilege of wearing the official badge of technical members, is given to all members of the Rocky Mountain Club at the time of consolidation. These special Rocky Mountain memberships shall be claimable by any member of the Rocky Mountain Club, not already a member of the Institute,

Jan 1, 1929

By Conrad W. Stellar, John L. Paynich

Design/Build concept that provides for earliest possible completion and lowest cost is presented. Elements of the program include: joint cooperation between owner, designer and builder; schedule construction sequence; and a line budget. Benefits over lump sum contracts are reviewed.

Jan 1, 1979

By R. W. M. Lai

This paper presents a simple flotation kinetics model (Lai, 1981) along with a method of presenting the model in an informative graphical form. Examples are given for evaluating various flotation conditions and different ore types.

Jan 1, 1983

By H. M. Howe, W. E. C. Eustis

THE processes which form the Subject of this paper have been experimented on in the laboratory of W. E. C. Eustis, but have not passed beyond the experimental stage. The first is the invention of Mr. J. L. Thomson, of Capelton, Quebec, Canada, the others have been invented by the writers. THOMSON'S PROCESS FOR THE EXTRACTION OF NICKEL This consists essentially in first rendering the nickel magnetic, and then separating it from the materials. with which it is mechanically

Jan 1, 1882

By H. J. Hager

The Alabama By-Products Corp. is an entirely independent Alabama enterprise. Organization of the company stemmed from the consolidation of three important properties in the Birmingham District and a by-product coke plant at Tarrant, Ala. In 1924 ABC was merged with the Pratt Consolidated Coal Co. This merger greatly extended the company's holdings of valuable coal lands in Walker and Jefferson Counties.

Jan 12, 1950

By Warren L. Howes

This paper deals primarily with an investigation of ball-mill liners that was conducted by the writer over a period of six years at the Mammoth mill in Arizona. The investigation covered a wide variety of designs of liners in both primary and secondary mills. The comparative results are presented herein as evidence of the extent to which design influenced liner life and mill performance. Flowsheet The feed to the Mammoth mill was a complex, oxidized, gold-silver-lead-molybde-num-vanadium ore with rhyolite, andesite and granite as gangue. Although the ore varied between stopes, the long-term average in character remained substantially the same. Capacity was 560 tons per day.† Fig. I shows an abbreviated flowsheet of the grinding section of the mill. Primary Ball Mill A 3-ft. Symons shorthead crusher in open circuit crushed to 1/4-in. maximum one-way dimension the feed to the 5 by Io-ft. Marcy open-end ball mill. The mill rotated at 80 per cent of critical speed and was charged with 4-in. forged steel balls. Cast balls were used for a few months at a slight reduction in ball cost, but breakage of the large balls reduced the ball size and grinding capacity to a point where the over-all costs suffered out of proportion to the saving in cost of balls. For metallurgical reasons, the finished product of the mill was maintained at minus 8-mesh. This coarse product, plus the very abrasive ore and the absence of fines in the feed, caused abnormally rapid wear of the mill liners. The resultant high operating cost led to the most extensive phase of the investigation. In order to clarify the difference in design of the various types of liners used, Fig. a shows the profiles with the arrangement in which grinding balls of maximum size would lie on the face of the liners. The results with each type of shell liner in the primary mill are shown in Table I. Since most of the testing was done with

Jan 1, 1943

By Warren L. Howes

This paper deals primarily with an investigation of ball-mill liners that was conducted by the writer over a period of six years at the Mammoth mill in Arizona. The investigation covered a wide variety of designs of liners in both primary and secondary mills. The comparative results are presented herein as evidence of the extent to which design influenced liner life and mill performance. Flowsheet The feed to the Mammoth mill was a complex, oxidized, gold-silver-lead-molybde-num-vanadium ore with rhyolite, andesite and granite as gangue. Although the ore varied between stopes, the long-term average in character remained substantially the same. Capacity was 560 tons per day.† Fig. I shows an abbreviated flowsheet of the grinding section of the mill. Primary Ball Mill A 3-ft. Symons shorthead crusher in open circuit crushed to 1/4-in. maximum one-way dimension the feed to the 5 by Io-ft. Marcy open-end ball mill. The mill rotated at 80 per cent of critical speed and was charged with 4-in. forged steel balls. Cast balls were used for a few months at a slight reduction in ball cost, but breakage of the large balls reduced the ball size and grinding capacity to a point where the over-all costs suffered out of proportion to the saving in cost of balls. For metallurgical reasons, the finished product of the mill was maintained at minus 8-mesh. This coarse product, plus the very abrasive ore and the absence of fines in the feed, caused abnormally rapid wear of the mill liners. The resultant high operating cost led to the most extensive phase of the investigation. In order to clarify the difference in design of the various types of liners used, Fig. a shows the profiles with the arrangement in which grinding balls of maximum size would lie on the face of the liners. The results with each type of shell liner in the primary mill are shown in Table I. Since most of the testing was done with

Jan 1, 1943

By Warren L. Howes

THIS paper deals primarily with an investigation of ball-mill liners that was conducted by the writer over a period of six years at the Mammoth mill in Arizona. The investigation covered a wide variety of designs of liners in both primary and secondary mills. The comparative results are presented herein as evidence of the extent to which design influenced liner life and mill performance. FLOWSHEET The feed to the Mammoth mill was a complex, oxidized, gold-silver-lead-molybdenum-vanadium ore with rhyolite, andesite and granite as gangue. Although the ore varied between stopes, the long-term average in character remained substantially the same. Capacity was 560 tons per day. [t] Fig. I shows an abbreviated flowsheet of the grinding section of the mill. PRIMARY BALL MILL A 3-ft. Symons shorthead crusher in open circuit crushed to ¼ -in. maximum one-way dimension the feed to the 5 by 10-ft. Marcy open-end ball mill. The mill rotated at 80 per cent of critical speed and was charged with 4-in. forged steel balls. Cast balls were used for a few months at a slight reduction in ball cost, but breakage of the large balls reduced the ball size and grinding capacity to a point where the over-all costs suffered out of proportion to the saving in cost of balls. For metallurgical reasons, the finished product of the mill was maintained at minus 8-mesh. This coarse product, plus the very abrasive ore and the absence of fines in the feed, caused abnormally rapid wear of the mill liners. The resultant high operating cost led to the most extensive phase of the investigation. [ ] In order to clarify the difference in design of the various types of liners used, Fig. 2 shows the profiles with the arrangement in which grinding balls of maximum size would lie on the face of the liners. The results with each type of shell liner in the primary mill are shown in Table I.

Jan 1, 1943

EXECUTIVE COMMITTEES OF LOCAL SECTIONS New York LOUIS D. HUNTOON, Chairman. ARTHUR S. DWIGHT, Vice-Chairman. THOMAS T. READ, Secretary, Woolworth Bldg., New York, N. Y. E. MALTBY SHIPP, Treasurer. GEORGE F. KUNZ. W. DE L. BENEDICT. Boston ROBERT H. RICHARDS, Chairman. ALBERT SAUVEUR, Vice-Chairman. AUGUSTUS H. EUSTIS, Secretary-Treasurer, 131 State St., Boston, Mass. TIMOTHY W. SPRAGUE, HENRY A. WENTWORTH. Columbia F. A. THOMSON, Chairman. GEORGE W. RODDEWIG, Vice-Chairman. LYNDON K. ARMSTRONG, Secretary-Treasurer, P. 0. Drawer 2154, Spokane, Wash. R. S. McCAFFERY, S. H. RICHARDSON.

Jan 4, 1914

By T. H. Alden

A correlation has been found in rock-salt structure single crystals between the latent hardening, measured by the direct stress activation of oblique slip systems, and the stress-strain behavior in simple compression. Materials with high latent hardening, like LiF, strain-harden at a low rate (Stage I) even when severely constrained. KCl, in contrast, shows low latent hardening and a tendency to strain-harden at a high rate (Stage 11). This correlation suggests that oblique slip is essential for Stage II hardening of these materials. THE role of secondary slip in the strain hardening of metal single crystals is a topic of lively controversy. On the one hand are theories in which secondary dislocations participate directly in Stage II hardening in the fcc metals, for example through the production of sessile dislocations,1 forest intersections, or jog formation. Much of the experimental evidence on which these theories are based has been reviewed by Clarebrough and Hargreaves.~ On the other hand, a recent theory5 denies that secondary slip has an essential role in Stage II hardening or in the transition from Stage I to Stage 11. In the latter view, Stage I is not terminated by an increase in the activity of secondary systems but by the exhaustion of undeformed material.6 The experiments reported in this paper will not resolve this controversy since the materials being studied are cubic ionic crystals rather than metals. However, the results do show in an unusual way a direct connection between "secondary" (nonortho-gonal or oblique) slip and strain hardening in these materials. Specifically, a correlation has been found between two independently measured properties, first the latent hardening of oblique (110)(1i0) slip systems as measured by direct stress activation of these systems, and second the stress-strain behavior at small strains. From prior work, it was known that in most cubi-cally oriented rock-salt structure crystals, two orthogonal slip systems operate and exclude the other equally stressed pair, oblique to the first pair.7'8 This observation apparently indicates that a significant interference exists between slip on oblique (110) planes and a relatively small interference between orthogonal (110) planes. The present experiments were begun with the intent of obtaining a quantitative measure of this difference by means of a study of latent hardening in these crystals. I) EXPERIMENTAL METHODS The experiments were basically of two types, first the determination of stress-strain curves by compression along a single (100) axis, and second the measurement of latent hardening by compressive prestrain along one cube axis followed by the determination of the yield stress in a second (latent) cube direction. All tests were done at room temperature in an Instron machine by compression between lapped, parallel steel faces. Three specimen shapes were used. For long crystals (nominal dimensions, 1/8 in. square by 1/2 in. long) the ends were lubricated with an oil-graphite mixture. Superior results with short crystals (about 1/8 in. cube) were obtained using 0.003-in. teflon film.' Thin crystals (1/4 in. square by 3/32 in.) were used for latent-hardening measurements and similar results were obtained with either lubricant. Test specimens were cleaved from Harshaw single crystals which had been irradiated to a dose of lo8 roentgen using a cobalt-60 source. The irradiation raises the yield stress and tends to prevent plastic deformation during sample preparation.10 Prior to testing, the irradiation hardening was removed by an anneal at 400°C. Ideal compression specimens have flat, parallel faces. In short specimens particularly, satisfactory results demand a close approximation to this ideal. In the present work, cleaved surfaces were often used directly as compression faces. The degree of success using this method depends on two factors: 1) the smoothness of cleavage faces, and 2) the extent to which the crystal is deformed or crushed by the chisel during the cutting of a long crystal into short pieces. Unfortunately, only one material of those studied, LiF, was completely satisfactory. NaF, NaC1, KC1, and KBr behaved less well so that

Jan 1, 1964

By Frederick Laist

This paper is a review of Montana reverberatory smelting practice covering a period of approximately fifty years, during which time the small furnaces that had been in use elsewhere for a century or more, without much change in size or method of operation, were revolutionized and were developed into the huge, continuously operating furnaces of today. A study of Montana practice is particularly instructive, since reverberatory furnace smelting for the production of copper matte received more attention there than in other smelting centers and many of the improvements that finally resulted in establishing the preeminence of this type of furnace over the blast furnace originated in Butte and Anaconda. The material in this paper was gathered from original sources, wherever possible, and all of the illustrations were made from original drawings, some of which have been simplified and worked over so as to be better adapted for reproduction. The aim has been to trace the modifications in design and operation which took place during the period in question—the reasons for the changes and the results achieved through them. For developments during the first twenty years, the technical literature of the period was freely drawn upon, but I am particularly indebted to W. M. Kelly, general foreman at the Anaconda Works, whose recollections and personal experience extend back to the early days. I wish to acknowledge the use made of publications of E. P. Mathewson, William Wraith and L. V. Bender, as well as information obtained here and there from friends and associates. The resume of Great Falls practice was compiled from correspondence, notes and drawings found in the files of the old Boston & Montana Co. and the tabulations showing the performance of furnaces at Butte and Anaconda are adapted from plant records and correspondence in the files of the Anaconda Copper Mining Company. The paper deals with some interesting comparisons that were made between furnaces operated under various conditions in connection with the Carson Case, and results obtained when using natural gas as fuel. This part of the paper may be considered original to the extent that these results have not previously been published.

Jan 1, 1934

By John Birkinbine

The press, trade publications, and special circulars, some elaborately illustrated, have been liberally employed within recent years in this country, to set forth the advantages of various locations as industrial centers, having as a basis the possibility of profitably producing pig-iron at these proposed centers: and special stress has been placed upon opportunities believed to exist at certain points for making iron of a quality suitable for the manufacture of Bessemer steel. The remarkable statements and prophecies made in some of these publications, have suggested the present paper, treating of the influence which location exerts upon the special industries named.

Jan 1, 1893

By R. J. Stoehr, F. Howell

Since the ore mined in the Grants-Ambrosia Lake uranium area is taken from a water-saturated sandstone formation, part of the milling operation includes a drying process. The authors discuss the merits and disadvantages of two methods: natural drying and mechanical gas-fired drying; operating and cost data are included. In the Grants-Ambrosia Lake uranium area, approximately 7000 tons of ore are mined each day from a water-saturated sandstone formation. This ore is sampled and treated at four separate milling operations. Prior to the design and initial construction of the milling facilities, very little was known as to the physical properties of the ore which would be handled in the sampling and crushing facilities at the mills. All four mills initially were constructed without ore-drying facilities. As mining proceeded, it was determined that, even after drying the ore in place by use of drainage development underground, the moisture content of the ore as hoisted averaged approximately 18 pct. Actually, some of the mines produced ores which resembled cream-of-wheat in character and had a moisture content in excess of 24 pct. Each of the four mills had a differently designed sampling and crushing plant; therefore, the moisture content of the ores had varying adverse effects upon the operation of the plants. It was determined after some experience that most of the sampling and crushing facilities could not economically handle ore if the moisture content was greater than 10 pct—one operator considers 12 pct moisture as a maximum. In all of the plants, moisture content over 8 pct increases costs to some extent. In addition to the added sampling and crushing costs, some of the mills were located 15 to 20 miles from the mines and the high moisture content of the ores increased the haulage costs from the mine to the mill. It was generally conceded that it was necessary to employ some method to reduce the moisture content of the ore prior to sampling. Several methods were considered: 1) natural drying at the mine site, 2) mechanical gas-fired drying at the mill site, 3) mechanical gas-fired drying at the mine site, 4) radiant heating on concrete clabs, and 5) infrared shed drying. After preliminary investigation all possibilities but natural drying and mechanical gas-fired drying at the mill site were eliminated. NATURAL DRYING A cooperative feasibility study was conducted on the natural drying method. This study indicated the following: 1) During summer months May through September, ore piled 4-ft deep would dry from +20 to +10 pct HzO in 30 days with no mechanical turning. 2) In the first four days after piling a reduction of 5 to 7 pct total moisture content was accomplished by drainage and absorption of the water into the underlying ground on which the ore was piled, providing the ground surface absorption rates approached 10 gal per sq ft per day. After the first four days the decrease of moisture caused by drainage was practically nonexistent. 3) In the summer months drying by evaporation amounted to approximately 0.1 pct decrease in total moisture per day and mechanical turning of the ore could increase this as much as three times. 4) Climatic conditions of the area indicated that: a) Air temperatures averaged 64' May, June, July, August, September; 41" October, November, December, March, April; 31" January, February. b) Average rain fall was 10 in. with 40 pct of this occurring during July and August. c) Only on very rare occasions were there over five consecutive days with below freezing temperatures. d) The annual evaporation rate was approximately 75 in. On the basis of this study, two of the mill operations decided to attempt to meet the moisture specifications by natural drying supplemented by mechanical turning. The other two operations decided upon rotary gas-fired drying at the mill site. The natural drying method has been quite successful in practice. The ore running approximately 18 pct moisture is trucked from the head frame and piled in rows about 6 ft wide, 3 1/2 ft deep, 5 feet apart during the months of May through September. In approximately 30 days this ore will

Jan 1, 1961

By J. A. Ede

The object of the writer is to call attention to a rather unique aggregation of economic products distributed over a line of succeeding formations about 3 mi. long, to be seen within a few miles of La Salle, Ill. Fig. 1 is an ideal section of the stratification exposed and exploited along a distance of 3 1/5 mi. in a southwesterly direction from the quarry of the Utica Hydraulic Cement Co. located near the historic site of Kaskaskia village to the Oglesby shaft at Oglesby. No attempt has been made to cover the whole field, special mention only being made (with the exception of two places) of the operations found along the course or parallel to the direction assumed in the ideal section. I have used Fig. 2, after J. R. Bent and De Witt Kelly, to locate the relation of the La Salle anticline to the coal mines of this district and to show the operation of No. 1 and 3 mincs of the Illinois Zinc Co. Anticline and the Rock Formations Owing to the structural deformation between La Salle and Utica, the older rocks of the state are exposed to the surface along the northern embankment and the bottoms of the Illinois River valley near the latter place. At; the Illinois Zinc Co. works, Sec. 16, Tp. 33, R 1, a well for water mas sunk 1828 ft. and samples taken every 10 ft. of the ground penetrated; duplicates were sent to Mr. Cady of the Illinois Geological Survey. A general compilation or synopsis study of this section is here presented. As the well is over 1 mi. west of the Western limb of the anticline, the section affords some reliable data. These samples were studied and interpreted by H. M. DuBois as Lower Magnesian, and by G. H. Cady as the Lower Magnesian. The results are given in Fig. 3. The most interesting geological feature of this district is the La Salle anticline. In 1865, Leo les Quereux, looking at Split Rock, asked how it happened that the upper coal measures overlie strata of the Lower Silurian and what has become of the formations which are generally found intermediate—the Upper Silurian, the Devonian and sub-carboniferous, and the lower member of the coal measures?

Jan 1, 1920

By James W. Halley

"Fine-grained" steels have been standard products for many years. This paper describes an investigation of the effects of some of the more common grain-growth inhibitors used to produce these steels. The properties, response to heat-treatment, and the deoxidation practice necessary to produce "fine-grained" steels have been the subjects of numerous papers. It has been shown that a substantial quantity of aluminum is necessary to produce this type of steel, and it has been indicated that titanium and zirconium produce a similar result. For some time there was a lively argument between those who felt that aluminum refined the grain and those who felt that aluminum oxide was the effective agent. This argument subsided with an apparent victory for those promoting aluminum oxide. Most of the work on grain size has divided steels into two broad classifications based upon McQuaid and Ehn's original carburizing test at 1700°F or some similar test at this temperature. If the steel coarsened at this temperature, it was coarse grained, while if it did not it was he grained. Quantitative data concerning how much a certain amount of aluminum raised the coarsening temperature and affected the properties, all other factors being constant, are very meager. Similar information regarding titanium and zirconium is practically nonexistent. The published information on aluminum yields some quantitative information. Epstein, Nead and Washburn' gave the first quantitative information on the amount of aluminum necessary to prevent grain growth at 1700°F. They showed that the addition of a pound to a pound and a half of aluminum per ton (0.05 to 0.075 per cent) would assure steel that would not coarsen during a McQuaid-Ehn test at 1700°F. Herty, McBride and Houghg reported that a steel containing 0.020 per cent acid-soluble aluminum coarsened between 1742° and 1832°F., while steels containing 0.016 per cent and 0.017 per cent acid-soluble aluminum coarsened between 1652° and 1742°F. compared with similar aluminum-free steels that started to coarsen at 1580°F. Herty3 also showed a marked improvebent in low-temperature notched impact resistance with increasing acid-soluble aluminum up to 0.030 per cent. McQuaid4 compared the coarsening of steels containing 0.011 to 0.204 per cent total aluminum and found a maximum coarsening temperature at 0.098 per cent aluminum. He had no samples between 0.015 and 0.098 per cent aluminum. Houdrement6 found a marked decrease in coarsening temperature with aluminum contents above 0.50 per cent. Kinzel, Crafts and Egan6 found that aluminum and zirconium improved the low-temperature impact resistance of a low-alloy steel, while titanium was detrimental. Sims7 shows that sulphur increases the coarsening temperature and that the maximum coarsening temperature is between 0.04 and 0.06 per cent added aluminum. The fact that the coarsening temperature passes through a maximum with increasing aluminum content appears to be well established. The aluminum content that

Jan 1, 1947

By James W. Halley

"Fine-grained" steels have been standard products for many years. This paper describes an investigation of the effects of some of the more common grain-growth inhibitors used to produce these steels. The properties, response to heat-treatment, and the deoxidation practice necessary to produce "fine-grained" steels have been the subjects of numerous papers. It has been shown that a substantial quantity of aluminum is necessary to produce this type of steel, and it has been indicated that titanium and zirconium produce a similar result. For some time there was a lively argument between those who felt that aluminum refined the grain and those who felt that aluminum oxide was the effective agent. This argument subsided with an apparent victory for those promoting aluminum oxide. Most of the work on grain size has divided steels into two broad classifications based upon McQuaid and Ehn's original carburizing test at 1700°F or some similar test at this temperature. If the steel coarsened at this temperature, it was coarse grained, while if it did not it was he grained. Quantitative data concerning how much a certain amount of aluminum raised the coarsening temperature and affected the properties, all other factors being constant, are very meager. Similar information regarding titanium and zirconium is practically nonexistent. The published information on aluminum yields some quantitative information. Epstein, Nead and Washburn' gave the first quantitative information on the amount of aluminum necessary to prevent grain growth at 1700°F. They showed that the addition of a pound to a pound and a half of aluminum per ton (0.05 to 0.075 per cent) would assure steel that would not coarsen during a McQuaid-Ehn test at 1700°F. Herty, McBride and Houghg reported that a steel containing 0.020 per cent acid-soluble aluminum coarsened between 1742° and 1832°F., while steels containing 0.016 per cent and 0.017 per cent acid-soluble aluminum coarsened between 1652° and 1742°F. compared with similar aluminum-free steels that started to coarsen at 1580°F. Herty3 also showed a marked improvebent in low-temperature notched impact resistance with increasing acid-soluble aluminum up to 0.030 per cent. McQuaid4 compared the coarsening of steels containing 0.011 to 0.204 per cent total aluminum and found a maximum coarsening temperature at 0.098 per cent aluminum. He had no samples between 0.015 and 0.098 per cent aluminum. Houdrement6 found a marked decrease in coarsening temperature with aluminum contents above 0.50 per cent. Kinzel, Crafts and Egan6 found that aluminum and zirconium improved the low-temperature impact resistance of a low-alloy steel, while titanium was detrimental. Sims7 shows that sulphur increases the coarsening temperature and that the maximum coarsening temperature is between 0.04 and 0.06 per cent added aluminum. The fact that the coarsening temperature passes through a maximum with increasing aluminum content appears to be well established. The aluminum content that

Jan 1, 1947