Search Documents

By James Norman, O. C. Ralston, John Dasher

Most mineral products are used in the finely divided state, but some are sold in larger sizes. Coal, gravel, metallurgical fluorspar, phosphate rock, hematite, chro-mite, and other products are sold in sizes coarser than can be treated by many mineral-dressing methods. Gravity separation of coarser sizes by log washing and jigging is probably as ancient as any process now in use. The performance of jigs on a feed with sufficient difference in density of the minerals is excellent, but many families of minerals are too similar in density to be separated effectively by this method. The use of heavy suspensions of fine solids to separate coarse coal from bone and slate has been in use for some years. This separation by sink-and-float was limited until recently to light minerals. Development of galena and ferrosilicon as suspension media, by Minerals Beneficia-tion, Inc., at Mascot, Tenn., Pitcher, Okla., and Crosby, Minn., under patents granted during and since 1938, has permitted excellent results to be obtained on minerals of very similar densities up to 3.3. This process has been put In the hands of American Cyanamid Co. for exploitation, and further research now in progress may increase the density of suspension obtainable so that separations at a density of 4.0 may be practicable before this is published. The Huntington-Heberlein dense-medium process, developed in England, is also being commercialized in the United States by Sink and Float Corporation. Du Pont has developed a sink-and-float separation using halogenated hydrocarbons as parting liquids; at this writing, the method is used commercially only on coal but has been successful in the pilot plant on many other minerals using tetrabrom-ethane at densities up to 2.95. While these processes were being developed to extend the range of separation by difference in density to the coarser sizes, the Bureau of Mines was engaged in developing a process that will extend the range of separation by difference in wettability up to 2-in. size. War work has pushed aside its further development indefinitely. The results are published here with the hope that some use may be suggested that will justify post-war development, and so that readers that may be able to make immediate use of the scheme may have the information. Earlier Work It has been known since the time of Herodotus (B.C. 484(?)-425) that water-repellent particles will adhere to sticky surfaces. That early historian reports the recovery of gold from the mud of a lake

Jan 1, 1943

By James Norman, O. C. Ralston, John Dasher

MOST mineral products are used in the finely divided state, but some are sold in larger sizes. Coal, gravel, metallurgical fluorspar, phosphate rock, hematite, chromite, and other products are sold in sizes coarser than can be treated by many mineral-dressing methods. Gravity separation of coarser sizes by log washing and jigging is probably as ancient as any process now in use. The performance of jigs on a feed with sufficient difference in density of the minerals is excellent, but many families of minerals are too similar in density to be separated effectively by this method. The use of heavy suspensions of fine solids to separate coarse coal from bone and slate has been in use for some years. This separation by sink-and-float was limited until recently to light minerals. Development of galena and ferrosilicon as suspension media, by Minerals Beneficiation, Inc., at Mascot, Tenn., Pitcher, Okla., and Crosby, Minn., under patents granted during and since 1938, has permitted excellent results to be obtained on minerals of very similar densities up to 3.3. This process has been put in the hands of American Cyanamid Co. for exploitation, and further research now in progress may increase the density of suspension obtainable so that separations at a density of 4.0 may be practicable before this is published. The Huntington-Heberlein dense-medium process, developed in England, is also being commercialized in the United States by Sink and Float Corporation. Du Pont has developed a sink-and-float separation using halogenated hydrocarbons as parting liquids; at this writing, the method is used commercially only on coal but has been successful in the pilot plant on many other minerals using tetrabromethane at densities up to 2.95. While these processes were being developed to extend the range of separation by difference in density to the coarser sizes, the Bureau of Mines was engaged in developing a process that will extend the range of separation by difference in wettability up to 2-in. size. War work has pushed aside its further development indefinitely. The results are published here with the hope that some use may be suggested that will justify post-war development, and so that readers that may be able to make immediate use of the scheme may have the information. EARLIER WORK It has been known since the time of Herodotus (B.C. 484(?)-425) that water-repellent particles will adhere to sticky surfaces. That early historian reports the

Jan 1, 1942

By James Norman, O. C. Ralston, John Dasher

Most mineral products are used in the finely divided state, but some are sold in larger sizes. Coal, gravel, metallurgical fluorspar, phosphate rock, hematite, chro-mite, and other products are sold in sizes coarser than can be treated by many mineral-dressing methods. Gravity separation of coarser sizes by log washing and jigging is probably as ancient as any process now in use. The performance of jigs on a feed with sufficient difference in density of the minerals is excellent, but many families of minerals are too similar in density to be separated effectively by this method. The use of heavy suspensions of fine solids to separate coarse coal from bone and slate has been in use for some years. This separation by sink-and-float was limited until recently to light minerals. Development of galena and ferrosilicon as suspension media, by Minerals Beneficia-tion, Inc., at Mascot, Tenn., Pitcher, Okla., and Crosby, Minn., under patents granted during and since 1938, has permitted excellent results to be obtained on minerals of very similar densities up to 3.3. This process has been put In the hands of American Cyanamid Co. for exploitation, and further research now in progress may increase the density of suspension obtainable so that separations at a density of 4.0 may be practicable before this is published. The Huntington-Heberlein dense-medium process, developed in England, is also being commercialized in the United States by Sink and Float Corporation. Du Pont has developed a sink-and-float separation using halogenated hydrocarbons as parting liquids; at this writing, the method is used commercially only on coal but has been successful in the pilot plant on many other minerals using tetrabrom-ethane at densities up to 2.95. While these processes were being developed to extend the range of separation by difference in density to the coarser sizes, the Bureau of Mines was engaged in developing a process that will extend the range of separation by difference in wettability up to 2-in. size. War work has pushed aside its further development indefinitely. The results are published here with the hope that some use may be suggested that will justify post-war development, and so that readers that may be able to make immediate use of the scheme may have the information. Earlier Work It has been known since the time of Herodotus (B.C. 484(?)-425) that water-repellent particles will adhere to sticky surfaces. That early historian reports the recovery of gold from the mud of a lake

Jan 1, 1943

By Claudio Guarnaschelli

Alteration of the electronic distribution of mineral surfaces by light irradiation has been used to modify the adsorption characteristics of flotation reagents. Energy of a few electron volts is suficient to cause the necessary transitions that either enhance or retard the adsorption phenomenon. The adsorption characteristics of potassium ethyl xanthate on galena and marmatite are presented as functions of the energy of illumination, type of semiconductor, and surface oxidation. In dilute solutions, the adsorption differences are readily detected by controlled kinetic measurements. The correlation between the electronic distribution and the adsorption and desorption phenomena at the solid surface is gaining more attention and acceptance. These interrelations have found a practical application in mineral processing since all of the sulfide minerals display semiconducting properties. By varying the ratio of free electron to electron vacancies, the separation of ilmenite from rutilel and zircon from pyrochlore" has been executed successfully. Plaksin et al.' indicate three possible ways of utilizing the semiconductor properties of a mineral. The first one involves the control of the oxidation-reduction potential of the liquid phase, the second one consists of allowing selected additives to diffuse through the mineral surface, while the third one entails a change in the adsorption and chemical activity of minerals by irradiating their surface. The aim of the present work is to consider the effect of irradiation on the adsorption-desorption characteristics of natural minerals. Since the effect of irradiation is to change the electronic distribution at the surface:

Jan 1, 1971

By D. D. Pollock, G. P. Conard II

Equations of the form of the Mott and Jones equations for the absolute thermoelectric powers of metals are derived primarily from a thermodynamic approach. The behaviors of transition thermoelements in common use are then examined and compared with this simple theory. MOTT and ones' derived a general expression for the absolute thermoelectric behavior of metals and alloys using the approach of the solid state physicist. This expression was then applied to specific cases.1,2 The present work develops equations of the same form principally by a thermodynamic approach. These relationships are then employed to gain some insight to the behavior of the transition thermoelements in common use. I) DERIVATION OF AN EXPRESSION FOR ABSOLUTE THERMOELECTRIC POWER First consider a metallic conductor which is maintained in a temperature gradient with no current flowing. At constant pressure, there will be a gradient of the free energy (F,) given by:

Jan 1, 1963

By H. P. Bucker, M. Felsenthal, F. R. Conley

INTRODUCTION In the intensive analysis of core samples from oil raservoirs, there is a recognized need for pore sizc distribution data. Such data, if collected with adequate precision and in sufficient quantity, should contribute to a better interpretation of fluid flow phenomena than is now possible from a knowledge of permeability and porosity data alone. It is hoped, for instance, that pore size distribution data may eventually provide a useful aid for predicting whether a water flood, or other secondary recovery methods. will he successful in a given reservoir.' Apparatus tor measurlng pore size distribution by mercury injection at pressures ranging from 0 to 2,000 psi have been described in the literature.2,3,4 All of these apparatus are somewhat complex and fairly expensive. Furthermore, the callbration of some of the apparatus is not always easy. Great difficulty, for instance, was experienced in obtaining reproducible pressure-volume correction data for the mercury pump shown in one of the references. An apparatus was therefore developed which was less complicated and less expensive than those of previously described designs. This apparatus is, in some respects, an improved version of a previously described low pressure apparatus' (maximum pressure 150 psi) which did not cmploy a mercury pump but instead used a precision bore glass tube for measuring the injected volumes. Tests were performed with the apparatus from vacuum to 2,000 psi and it was observed that the apparatus furnished reproducible pressure-volume correction data. In addition. it was noted that the maximum correction was small. precision of measurement was high. and operation of the entirc apparatus was relatively easy. Although the apparatus was designed exclusively for samples of 1 in. diameter and 1 in, length or smaller, it could be modified without much difficulty for larger samples, if desired. APPARATUS Arrangement of the pore six distribution apparatus is shown schematically in Fig. I. The heart of the apparatus is a steel sample chamber surmounted by a precision bore capillary glass tube. A mercury reservoir is connected to the lower half of the sample chamber. The top of the glass tube is in communication with a

Jan 1, 1957

Until the end of 1960, the small primary aluminum industry in Australia was run by the government. The entire operation was at Bell Bay on the north coast of Tasmania. It consisted of an alumina plant and smelter, owned jointly by the Commonwealth and the State of Tasmania. Apparent domestic demand that year was about 48,000 long tons; 11% thousand came from Bell Bay; the rest was imported. By March 1964, Australia had two fully integrated aluminum companies. The government has stepped out of the picture and the key word of the industry from bauxite to metal is "growth." Present annual capacity of the two companies for making aluminum metal totals 92,000 long tons a year. Australian demand is about 60,000 tons. By 1968 Australian consumption should be 90,000 tons and by 1970 it is expected to reach 107,000 long tons per year. Export markets for bauxite, alumina and metal are developing.

Jan 10, 1964

By D. G. Westlake

NUMEROUS hydride habit planes in zirconium, Zircaloy-2, and Zircaloy-4 have been observed by various researchers and have been compiled by Louthan and Angerman.1 While only partial agreement exists on the identification of these habit planes, there is a growing consensus that a tensile stress applied on a polycrystalline rod during slow cooling will cause the hydride platelets to lie perpendicular to the tensile axis. walters2 agrees with Louthan and Angerman who reason that "The particular plane on which precipitation will occur is the plane that will result in the maximum relief of stress by precipitation of the low-density hydride." The experiment described below was initiated to test this hypothesis on a single crystal of zirconium. A single-crystalline tensile specimen of zone-refined zirconium, designated number 13 in a previous study,3 had a square cross section with one pair of parallel faces only 4 deg from the basal plane of the hcp structure. The tensile axis was about 86 deg from the (0001) pole, 14 deg from the (1010) pole, and 16 deg from the (1150) pole. The specimen was charged to 50 ppm H by allowing reaction with the correct amount of hydrogen at 1073°K, homogenizing at this temperature for 2 hr, and cooling in the furnace. Two- surface analysis revealed that hydride platelets had precipitated parallel to the three {1010} prism planes. The specimen was heated to 673°K, in air, for 16 hr to bring the hydrogen back into solid solution, and furnace-cooled to 573°K.* It was then stressed in ten- sion at 1.2 kg per sq mm. (This produced a resolved shear stress of 0.6 kg per sq mm for glide on the prism plane with the highest Schmid factor. A higher stress would have produced significant strain at this temperature because the critical resolved shear stress for prism-plane glide in this crystal was only 1.0 kg per sq mm at ambient temperature.) The poles of the three prism planes were at angles of 14, 46, and 74 deg to the tensile axis so that an applied stress would exert normal stresses on the three planes in the approximate ratios 10:5:1, respectively. As soon as the stress was applied, the sample was furnace-cooled to room temperature. It was ground on wet Sic paper and chemically polished in 50 parts HNO3, 50 parts water, and 7 parts HF before examination. The result of the experiment was negative; i.e., the three (1010) planes were of equal importance as hydride habit planes.* It must be admitted that the ex- periment is not entirely comparable to those performed by walters,2 Louthan,5 and Louthan and Marshall6 on polycrystalline materials. They have found that some critical stress (below the macroscopic yield stress) is required for stress-orienting the hydrides. The applied stress in the present experiment was, by necessity, smaller by an order of magnitude than the critical stresses they report for the various materials. If the critical stress was related to the microstructure, one might postulate that it should be decreased by increasing the degree of perfection of the metal lattice and by increasing the grain size. But the experiment above suggests that, for the extreme case of a zone-refined single crystal of zirconium, the critical stress lies above that which one can apply without introducing gross plastic strain as another variable.

Jan 1, 1967

By William E. Hughes, Roderick K. Davey

The objective of this chapter is to review and discuss interpolation techniques commonly in use in the mining Industry today, including simple examples. This chapter will not attempt to compare the relative accuracy of each technique as this subject has adequately been covered by several authors (Knudsen and Kim, 1967; David, 1974; and Barnes, 1979) When appropriate, methods will be compared relative to the results of simple examples and computational ease. The examples presented are based on metallic deposits. The techniques, however, are not restricted to metallic deposits and can generally be applied to nonmetallic ones. The purpose of interpolation, as applied to a mineralized deposit, 1s to extend the knowledge of the grade and geology of localized samples to an estimate of the grade and mineralogy of a larger block of ground or even an entire deposit. The word interpolation means to compute values between given values and is limited to that region between the known values. The distinction between interpolation and extrapolation is important and must be adhered to in the application of these techniques in general, the interpolation must be limited to the area enclosed by verified samples. The methods being discussed can be broadly broken into three categories. ( 1 ) geometrical methods, (2) distance weighting methods, and (3) geostatistical techniques.

Jan 1, 1979

By Peter R. Morris

The effecl of preferred orienlation on X-vay dzffvaction measurements of retained austenzte was investigated for four precipitation-hardening staznless steels in sheet form. A method is preserzted for estimating the ervor in measurement associated with a given samplirig direction. The method was used to select an "optimum" sampling direclion in order to minimize errors in measurement due to preferred orientation. hleasuremenls of retained austenite content employing lhe proposed sampling direction are conzpaved to measuretnents enzploying the more commonly used normal direclion for a series of sawzples. THE first application of X-ray diffraction to the measurement of retained austenite in steels is due to Sekito, 1 who employed a photographic technique in which the (111) reflection from a thin strip of gold affixed to a cylindrical sample was employed as a standard. Averbach 2 introduced the "direct comparison" method in which the ratios of observed to calculated random intensity are assumed proportional to the austenite and/or martensite contents. Averbach's work forms the basis of most subsequent X-ray diffraction methods for the determination of retained austenite. Subsequent improvements are due to: Averbach and Cohen,3 who employed a sodium chloride crystal to monochromate cobalt radiation; Averbach et a1.,4 who introduced a bent sodium chloride monochromator; Mager,' who used a bent quartz crystal to monochromate chromium radiation ; Littmam, who first used a geiger counter diffractometer for this purpose; Beu and Beu and Koistinen, 11,12 who studied effects of absorption factor, surface preparation, sample geometry, integrated intensity vs peak height, choice of radiation, monochromator, and filter. The possibility of errors in measured values due to orientation effects was noted by Miller,13 who suggested examination of a surface other than the plane of rolling. Lopata and Kula 14 have developed an experimental technique in which the preferred orientation is measured in each sample. They illustrated the method for a sample containing 42 pct retained austenite. Application of their technique to the 1 to 15 pct range typical for the precipitation-hardening stainless steels does not appear feasible. EXPERIMENTAL PROCEDURE The nominal compositions of the precipitation-hardening stainless steels investigated are listed in Table I. Ingots were solution-treated, hot-rolled to approximately 0.2 in., and reduced to 0.050 in. by a suc- cession of cold rolling and annealing operations. After this treatment the 17-4PH sample was in the marten-sitic condition, while the 17-7PH, PH 14-8Mo, and PH 15-7Mo samples were in the austenitic condition. Samples of 17-7PH and PH 15-7Mo steels in the mar-tensitic condition were obtained by heating to 1750'F for 10 min and holding at -100°F for 8 hr. A sample of PH 14-8Mo steel in the martensitic condition was obtained by heating to 1700°F for 1 hr and holding at -100°F for 8 hr, followed by aging at 950" for 1 hr. POLE FIGURE DETERMINATIONS Samples were thinned to 0.003 to 0.005 in. by etching in a solution containing 250 ml reagent-grade phosphoric acid (85 to 87 pct H3PO4), 250 ml technical-grade hydrogen peroxide (30 to 35 pct H 2 O 2), and 50 to 100 ml reagent-grade hydrochloric acid (37 to 38 pct HCl). The specimens were placed in an "integrating" sample holder which provided a 1-in. oscillation in the plane of the sample. The diffractometer was aligned to measure the intensity diffracted by planes of the particular {hkl} type being studied. The sample was Set for a given latitude angle, a, measured from the plane of the sheet, and diffracted intensity recorded as the longitude angle, 0, measured in the plane of the sheet from the rolling direction, was increased from 0 to 360 deg. After a 360-deg scan of B, a was incremented by 5 deg, and the process repeated. Random standards obtained by spraying suspensions of powdered iron (bcc structure) and nickel (fcc structure) in lacquer were used to correct observed intensities for absorption and geometrical effects. Zirconium-filtered molybdenum radiation was used to determine the transmission regions of the (111) (0to 45 deg), (200) (0 to 60 deg), and (220) (0 to 45 deg) austenite and (110) (0 to 45 deg), (200) (0 to 50 deg), and (211) (0 to 35 deg) martensite pole figures. Vanadium-filtered chromium radiation was used to

Jan 1, 1968

By Y. C. Kim, S. L. Barua

M. Armstrong's paper is very interesting and can be regarded as a pioneering work of applying geostatistics on washed coal. The density levels used in her study are uniformly spaced, which facilitated curve fitting through a proper experimental design. Most of the existing coal washing plants in the US, however, gather washability data at non-uniform intervals which, in turn, affects the goodness of curve fitting. We would like to emphasize the importance of having a proper experimental design, if a similar geostatistical application is to be conducted on washed coal. We, at the University of Arizona, tried the variogram on recovery (Kim, Barua, and Baafi, 1982, SME preprint 82-143) which showed a similar pattern as Fig. 4 of Armstrong's paper. In both cases, the first experimental variogram value is invariably and inexplicably higher than the second variogram value. Although Armstrong ignores the first point because of "small number of sample points," we did not do so because there were 17 sample pairs. As a consequence, we concluded that the obtained experimental variogram was unsatisfactory and that further research is warranted. In other words, this disagreement in variogram interpretation between M. Armstrong and the University of Arizona begs the question whether the experimental variogram of Fig. 4 truly reflects the spatial correlation in washed coal, assuming there is such a correlation. Finally, we wish that Armstrong could have done a similar study on clean sulfur, which is a vital interest to the coal mines in the US. Her implied remark on sulfur in the concluding section of the paper may turn out to be incorrect because our experimental variograms on clean sulfur at different density levels were even less satisfactory than those on recovery. ?

Jan 1, 1986

By P. G. Winchell, J. K. Jackson

The strtcture of body-centered Fe-Ni-C alloys (0 to 16.5 wt pct Ni) containing less than 0.015 wt pct C was investigated by measuring the carbon-diffusion peak at low frequencies with a torsion pendulurrr. By determining the Snoek damping in ferrite and in quenched alloys of identical composition, the effects of nickel content and heat treatment were separated, and the existence of a structure in which Snoek damping is greatly reduced was revealed in the quenched ternary alloys. The relative amount of this structure increases with increased nickel content and cooling rate. It is proposed that this structure may be highly imperfect or tetragonal. In Fe-Ni-C alloys containing only ferrite the addition of nickel (0 to 5.1 wt pet) decreases tke area of the carbon-diffusion peak and shifts its position to lower temperatures but broadens the peak only slightljl. The decrease in peak area with increasing nickel implies that short-range interactions with the nickel atoms prevent some of the carbon atoms from participating in the relaxation process. The shift in the peak position indicates a long-range effect of nickel on the movement of carbon atoms so that at 300°K the diffisivity of carbon in -ferrite is increased by about 35 pct by the addition of 5.1 tut pct Ni. The results are presented as distributions of relaxation strength 072 the activation energy under the assumption that the frequency factor is invariant. BODY-CENTERED iron-base solid solutions dissolve carbon interstitially in the octahedral sites. The occupation of an octahedral site produces a tetragonal distortion of the surrounding lattice. These sites fall into three sets according to the orientation of the tegragonal distortion associated with each and may be identified by their lattice coordinates as: type 1/2 0 0, type 0 1/2 0, type 0 0 1/2. At low carbon levels in cubic ferrite the carbon atoms are distributed at random1 among these sites. In high-carbon body-centered iron-base solid solutions, which are unstable with respect to several two-phase mixtures, a tetragonal structure occurs as the product of the diffusionless transformation of austenite. This transformation is commonly accompanied by appreciable microstrain and its product is called martensite. The tetragonality of martensite, a supersaturated solution of carbon in a iron, is maintained prior to decomposition even though local diffusion of carbon occurs as evidenced by carbide precipitation. The tetragonality is taken as evidence that one set of octahedral sites is preferentially occupied by carbon. (This preferential occupation is called ordering below.) Support for this view is presented by the absence of strain-induced carbon-atom diffusion in high-carbon solid solutions (martensite). Such diffusion occurs in ferrite and produces the 40°C internal-friction peak observed at 1 cps frequencies.' Thus, there appears to be qualitative evidence favoring the view that at sufficiently high carbon levels tetragonality arises spontaneously as a result of the ordering of the carbon atoms; however, no experimental evidence exists concerning an equilibrium between cubic and tetragonal body-centered solid solutions. Moreover, attempts to estimate the energy of ordering7-' predict a value too low to maintain the tetragonality observed at medium carbon levels, 0.3 to 0.6 wt pct C. In the present work an attempt using internal-friction measurements is made to establish the presence or absence of tetragonality in low-carbon body-centered solid solutions formed by quenching austenite. Fe-Ni alloys containing about 0.01 wt pct and 0 to 15 wt pct Ni were selected for the study. While the work was in progress Gilbert and Owen10 reported that the transformation which occurs in these alloys during quenching at rates up to 5000°C per sec is not martensitic but is more properly categorized as massive. Thus, the solid solution

Jan 1, 1964

By Leon Keller, William R. Van Slyke, James Stukel

Two 4-ft wide DSM screens were installed during 1957 in one unit of the two-unit heavy media cy- clone section of the Holman-Cliffs concentrator at Taconite, Minn., following successful laboratory test work on a 1-ft screen. The two screens materially reduced the amount of media sent to the magnetic separator cleaning circuit. Wear life was good and fine size capacity was high. Briefly, the Holman-Cliffs heavy media cyclone plant uses -65 mesh magnetite as media and 10-in. diam., 30º Ni-Hard cyclones as separatory vessels. Feed to the plant averages 130 long tons per hr of -1/8 in. +65 mesh material. The conventional heavy media circuit uses drum or spiral type separatory units and treats +l/8 or 3/16-in. material. The medium is generally -65 mesh ferrosilicon. Ore and media are readily separated by screening at about 6 mesh. At this size, capacity is high and wear and maintenance are not excessive. The heavy media cyclone plant requires an efficient separation between +65 mesh ore and -65 mesh media. To reduce costs, however, the separation was made at a coarser size with the result that the media was un- duly contaminated and it was necessary to clean large tonnages of media and ore in magnetic separators. Due to the high capital cost of these units, their number was kept to a minimum and, consequently, they were overloaded. As a result, the separation between magnetic media and nonmagnetics was not sharp and the magnetite losses were high.

Jan 10, 1958

By Anna H. Connard

SUMMARY The discussion focusses on developments in the debt/equity swap market since the Marte project was negotiated in early 1988. It emphasises carrying forward the recent market trends to anticipate the breadth and scope of debt/equity conversions for mine development in the 1990s. Secondary market prices of LDC paper, conversion values and political influences in the host countries and the use of near debt and commodity-based instruments as components of mine financing in debt/equity deals will be placed in the perspective of recent trends and expectations for the future. THE MARTE PROJECT The Marte mine is a gold porphyry deposit in Chile's high Atacama, for which financing was put together at the beginning of 1988. The Marte project was financed by a combination of common equity and loans. It was unusual that the equity infusions were made under different programs. Some of the international equity was infused with fresh funds via DL 600. Other common foreign equity was provided through the conversion of Chilean bank debt under Chapter XIX. On the loan side,. export credits for the import component of machinery and equipment were sought. Local bank financing was negotiated for the remainder of ' the project's anticipated cost. The debt conversion market in Chile was at its apex in terms of interest, activity and government support when the mine financing was arranged. The price of Chilean paper in the secondary market hovered about 62 to 66 cents per U.S. dollar of face value. Meanwhile, the Chilean government was negotiating conversion redemptions significantly closer to full face value. The government differentiated between debt paper exchanged for corporate investors who had sourced that paper in the secondary market, and debt paper held by bank investors who would incur a transaction loss in the conversion. The use of a combined DL 600lChapter XIX equity financing created different yield calculation bases for the various investors. Chapter XIX prevents remittance of profits before year 5 and capital repatriation before year 11. Investors choosing this vehicle have either for a corporate policy in the target project not to declare dividends until repatriation is allowed, or they have to seek uses for the peso liquidity that would be generated through dividend declarations in the early years. However, DL 600 investors face no such waiting period on dividends, nor do they have restrictions imposed on cashing out of the investment before the 11th year. Therefore, any equity structure with components of both investment mechanisms will have inherent differences in cost basis and future income flows for the various participants. This equity imbalance is defensible if the investment motivations of the parties are analyzed: a mining investor using fresh funds looks for a hurdle return on equity calculated at conservative commodity prices, with as much flexibility to reap upside benefits as possible; a mining investor choosing to invest through a debt conversion mechanism will realize a modest short term gain on the conversion, reducing his effective cost basis, but sacrificing some return because of the waiting period on repatriation of dividends. INVESTMENT OBJECTIVES A bank investor exchanging his own paper for an equity participation in a mining project realizes a conversion loss on the transaction. He seeks a risk adjusted acceptable hurdle rate of return to recoup that loss over time. Motivation for the bank investor to take that loss may be derived partly from a strategy to diversify its existing portfolio by internal policy and externally regulated guidelines. The bank will compare yields on its loan portfolio to that country with anticipated dividend flows discounted back at a risk adjusted rate. It will analyze the project with return objectives of yield enhancement over time and with

Jan 1, 1990

The useful minerals can be subdivided into two large groups. One comprises those which are mined because of their chemical composition. They represent the natural resources of certain materials or of energy (coal). The second group is used not because of their chemical composition but because of certain physical properties or combinations of physical properties. A large number of minerals are mined because of their hardness, their electrical and thermal properties, their color or plasticity. There has been increasing recognition of the value of mineral synthesis during the past 30 years. This is illustrated by the development of improved aircraft spark plugs and chemical porcelain about the time of the first World War. During World War II the impact of crystal chemistry upon ceramics became most pronounced. New ceramic bodies were tailor-made, such as those designed with a high dielectric constant and low power loss, for use in high-voltage, high-frequency communication. In the field of refractories special materials were needed for unusual heat-resisting service in jet and rocket engines, and in the processing of fissionable materials. The synthesis of natural minerals in the laboratory has long been of aid to geologists and mineralogists in their study of the origin of minerals and physico-chemical conditions under which certain minerals were

Jan 1, 1950

By A. E. Bellis

The time effect in reheating certain steels below the critical range is very marked. The increased toughness, shock-resisting power, and machinability of steel subjected to a long, high drawing temperature has been thoroughly demonstrated and is of practical importance, particularly in the manufacture of L'smokeless" rifle-barrel steel. The time effect in tempering is most important when a maximum drawing effect is desired, in which case the highest physical properties as well as ease of machining are important considerations. These are the conditions in drilling a rifle barrel. A hole, 0.30 in. in diameter and 24 in. long for the Springfield rifle, and 30 in. long for the Russian military rifle, has to be drilled in the heat-treated material. This barrel-drilling operation is probably the most difficult one in rifle manufacture, and anyone who has been connected with rifle manufacture knows how seriously production is affected when "hard" or non-uniform steel for barrels is encountered. The importance of high physical properties (tensile strength, toughness and resilience) in a rifle barrel is obvious. The physical properties of two different lots of barrel steel are given below. The first lot, No. 1, gave serious trouble in the drilling operation; the second gave no trouble at all. No. 1 No. 2 Elastic limit, lb. per sq. in.................... 117,450 116,800 Tensile strength, Ib. per sq. in................. 132,500 131,750 Elongation, per cent........................ 16.0 20.0 Reduction of area, per cent................... 42.1 51.0 Impact strength, ft.-lb. per sq. in.............. 450.0 520.0 This difference in machining and physical properties was due entirely to the time of reheating. The first lot was given a reheating time of 30 min., the second lot remained at the reheating temperature 2 hr. Both

Jan 1, 1918

By Warden A. Moller

The Fushun coal-field, now being opened up by the South Manchurian Railway Co., is connected with the main line by a branch, 30 miles long, from Sui Chia Tun, 10 miles south of hlukden, the oapital of Manchuria. The coal-field, which lies on the southern bank of the Hun river, 25 miles east of Xiukden, consists of a long narrow valley, running east and west between hills composed of granitic and volcanic rocks. At the foot of the northern hills, the Hun river flows westward towards the Liao river, which drains the greater part of South Manchuria. At the foot of the southern hills, resting immediately upon volcanic rocks, and overlain by 30 ft. of alluvium, is a thick layer of Tertiary shales, carrying near the base two coal-seams. In many places the lower of these two seams is in immediate contact with volcanic lavas and basalts, the flows of which were evidently both prior and subsequent to the formation of the coal-seams. This contact has practically destroyed the lower seam for commercial purposes. The value of the field lies in the upper seam, which, for a length of nearly 8 miles, varies from 100 to 130 ft. thick. Of this seam, 85 per cent. is good coal. The seam dips to the north conformably with the shales, at angles of from 25 to 30°, and appears to have an uninterrupted dip for about 1.5 miles before being possibly cut oft' by the northern hills. The coal-bearing shales extend east and west for a length of about SO miles, but towards the east the continuity of the seams is broken by intrusive rocks. The coal is of the sub-bituminous variety, low in ash, bright in appearance, and breaks with a conchoidal fracture. It has the usual qualities of Tertiary coal—quick steam-raising and poor stacking qualities. Pieces of resin, varging in size from

Jan 1, 1911

By C. J. Bise, E. K. Albert

Mathematical modeling and computer simulation are the two primary techniques used for production analysis of underground coal mine layouts. Oftentimes, however, the selection between these two techniques is not based on an awareness of the level of effort needed for input formulation versus the suitability of the desired output. This paper will review mathematical modeling and two of the more prominent simulators (Virginia Tech's FACESIM and Penn State's UGMHS) used in underground coal mine production analysis. A hypothetical section will be analyzed by these programs and, based on the results of the aforementioned study, their advantages and disadvantages will be discussed.

Jan 1, 1985

By H. C. Chao, L. H. Van Vlack

Small MnS inclusions with known crystallographic orientations were placed inside powder compacts of low-carbon steel. After the metal was axially campressed with negligible end friction, the deformstions for the metal and the inclusions were compared. The MnS inclusions deformed more when the [100] direction was aligned with the compression axis than when the [111] direction was parallel to this axis. The deformations of the inclusions in the two principal radial directions were equal for each of the above orientations. Inclusions with [110] compression alignments did not deform with radial symmetry. The relative deformation of the inclusion and metal was closely dependent upon the relatiue hardness of the two phases. The relative deformation of the two phases was not sensitive to the rate of deformation. RECENT studies by the authors1.&apos; suggested that the plastic deformation of MnS in steel would probably be highly sensitive to the orientation of the inclusions and to the temperature of the metal. This paper reports an investigation of these factors upon MnS behavior within steel. Manganese sulfide (MnS) possesses an NaCl-type structure and typically has extensive (l10) {110} slip as a separate (noninclusion) crystal.&apos; A secondary slip system, ( l 10) { l l l}, has also been observed where the major slip system is restricted. In general, MnS inclusions must be rated as a highly deformable second phase.3 The amount of sulfide deformation varies, however, with several composition and processing factors. Some of these have been only partially assigned. For example, it is known that minor amounts (<0.01 pct) of silicon within free-machining steels will increase the amount of MnS deformation,4 but the mechanism of the added deformation can only be surmised at the present. Manganese sulfide and steel have sufficiently comparable deformation characteristics so that slip which is started in steel may be continued through the sulfide inclusions and back into the steel if the crystal orientations are favorable.5 A more detailed discussion of previous work on the plastic deformation of NaC1-type crystals and on the plastic deformation of inclusions within a metal is given in Chao&apos;s work.6 EXPERIMENTAL PROCEDURE The manganese sulfide which was used in this study was prepared by previously described methods.&apos; Single crystals of MnS, both as cleavage cubes and as spheres, were oriented within steel powder compacts so that the desired crystal directions were parallel to the direction of axial compression. A four-stage hydrostatic compaction procedure was used and involved the following steps. In the first stage part of the powder was placed in a metal die 1 in. in diameter with a thick (1 in. OD, 5/8 in. ID) rubber liner which had one end plugged. The steel powder was hand-rammed, making it as dense as possible before placing a carefully sized MnS crystal (either as a sphere or as a cube) near the center. The crystal was oriented with the chosen direction vertical; viz., [001], [011], or [111], with the aid of a X10 microscope. A pair of tungsten wire threads 0.020 in. in diameter was inserted along the side of this (&apos;core compact" to locate the desired plane after the compression tests. After the crystal was positioned in the center of the die, more powder was added and carefully rammed by hand. The die was then capped with a rubber plug of the same hardness and thickness as that of the liner. The whole assembly as shown in Fig. 1 was compacted by a ram load of 54,000 lb (about 70,000 psi). In the second stage a smaller, 3/4-in, rubber-lined die was used to give a stress of approximately 120,000 psi. The above process was repeated with the initial compact serving as a core for a larger compact. The final product after sintering was a cylinder 1 cm long and 1 cm in diameter, having a density of 7.54 g per cu cm. This was close to the theoretical density since the metal contained a non-metallic phase. There was no evidence of MnS deformation during the hydrostatic compaction or subsequent sintering. Elevated-temperature hardness data were obtained by procedures previously described.2 Compression tests for inclusion deformation utilized the cylinders which were described above. The critical problem in these tests was the lubri-

Jan 1, 1965

By T. E. Kihlgren, N. B. Pilling, E. M. Wise

Systematic data are presented on the relation of composition of nickel silvers to color, tarnish resistance, hardness and liquidus temperatures, for alloys containing up to 30 per cent nickel and 50 per cent zinc, further modified at certain nickel and zinc contents by 0 to 8 per cent of tin and 0 to 10 per cent of lead. Attention has also been directed, using a still more limited range of alloys, toward a study of tensile properties and such casting properties and characteristics as fluidity, shrinkage and pressure tightness. In some of these, rather broad ranges of composition are dealt with; in others, it has been expedient to focus attention on the Federal Specification 20 per cent nickel silver casting alloy, WWP-541. Introduction The demand for an alloy essentially white in color, which could be cast and worked by simple methods and which possessed strength and corrosion-resisting properties superior to the usual brasses, led to the discovery and early use of cupronickel alloys containing zinc, and sometimes tin, lead and other metals. This type of alloy was generally known as &apos;German silver until the war, when the term "Nickel Silver" became generally accepted. The element principally responsible for the white color of the alloy and for its strength and corrosion resistance is nickel, which may constitute from 8 to 30 per cent of the alloy. The functions of the other elements will be described later. The manifold uses of nickel silver are largely due to its color, corrosion resistance, ease of casting, fabrication, joining and rather moderate cost. In many instances the alloy is finished by grinding and polishing while in others it may be finished with a silver or nickel plus chromium plate. Electroplates applied to a nickel silver base behave more satisfactorily than those applied to the softer and less resistant alloys, and owing to the white color of the underlying metal the article will retain a pleasing appearance despite local failures of the plating.

Jan 1, 1935