Search Documents

A New Ingersoll-Rand Turbo Blower The Ingersoll-Rand Co. has added to its Turbo Compressors and Blowers a low-pressure machine t o handle volumes from 3,000 to 35,000 cu. ft. per minute at from 1-2 ½ lb. These are particularly adapted to such service as foundry cupola blowing, atomizing oil for oil burners, supplying blast to heating and annealing furnaces of various kinds, blowing air for water-gas generators, pneumatic conveying and ventilating. They are of the single stage, double flow type and are furnished either electric motor, steam turbine or water wheel driven.

Jan 6, 1916

By H. W. Hardinge

Disregarding for the present the economic side of a new device, let us turn to that feature of the conical pebble-mill which is of interest from a scientific point of view, and consider the device as a puzzle in which the theories of the cylindrical type of mill have been increased. Many articles have been written on the theory of the tube-mill, and explanations have been made which do not explain ; but these have evolved suggestions of practice which have resulted in changes in the tube as to length, diameter, feed, discharge, speed of rotation, rotation on hollow trunnions, rotation on rings, and changes in the operation as to quantity and size of pebbles, charge of load above or below the axis, crushing by causing the larger pieces of the material of the charge to act as grinders, whether crushing is abrasive or impactive, etc. The practical worker in crushing. is first interested in the endeavor to reach an econonlic means of accomplishing a desired end; but the improvements in crushing-practice have been largely left to the manufacturer of machinery, who, as a rule, has little, if any, knowledge of the specific requirements— such as granulation, sizing for concentration without pulverizing the metals, instead of pulverizing the rock or gangue; the metals being the more friable, while the rock is tough and not so easily disintegrated. A reversal of this practice is the aim of sliming direct for cyanidation or pulverizing for cement, etc. In the ordinary cylindrical mill, having a diameter of 4 or

Jan 1, 1909

By Robert H. Richards

The extent to which sizing by sieves should be carried, as a preliminary to the separation, by jigging, of minerals of different specific gravities, has been a matter of controversy for many years. The subject has been investigated by several authorities, yet the ground does not seem to have been completely covered, nor are the questions involved entirely settled. For my present purpose I shall refer to but three investigators—Rittinger, Munroe, and Hoppe. In seeking additional light, I have gone over part of the old ground which has been considered satisfactorily settled; and since these preliminary tests have thrown light on some points, they have been included in this paper. In the investigations here described, I have confined myself, for several reasons, wholly to small sizes—grains of 0.1 inch in diameter and less. Rittinger's work was mainly done upon larger sizes, and there is much need among millmen of information concerning the smaller sizes. Moreover, these sizes brought the investigation within the means at my disposal. The laws that have been claimed as the laws of jigging by the several authorities are: 1. The law of equal-settling particles. 2. The lam of interstitial currents. 3. The law of acceleration. 4. The law of suction. The first of these has been considered by investigators, generally, to be the most important of all, and the larger part of the work of jigging is thought to be governed by it. But that it does not cover the whole of jigging is clear to all; and to account for the increased efficiency which we may call the extra jigging-catch, the other three laws have been advanced. The investigation described in this paper was undertaken to determine, as far as possible, to what extent each of the four laws con-

Jan 1, 1895

By R. A. Fitch, J. D. Griffith

A performance calculation method was used in conjunction with experimental studies to develop means of predicting and interpreting miscible floods and to explore possible methods. of improving their efficiency. The calculation method is based upon the division of reservoirs into multiple independent zones or strata. Comparison was made with some experimental floods and with a field project to obtain some measure of the applicability of the method. Two aspects of miscible flooding were considered: (I) the displacement of a miscible front through a reservoir, and (2) the distribution and utilization of the solvent volume injected to maintain miscibility. Calculations and experihental observations indicate that alternate gas-water injection behind a miscible front significantly improves miscible flood performance, both within a single stratum and in a multistrata reservoir. Calculations were made on the extent to which miscibiliry is maintained by a given solvent volume in a stratified reservoir. Two alternate criteria for determining the optimum volume of solvent for injection are discussed. The preinjection of a small volume of water ahead of the solvent is suggested as a method of obtaining more efficient utilization of solvent. Calculations and experiments were made to investigate the effects of water preinjection. INTRODUCTION Miscible fluid displacement as a possible means of recovering oil has been the subject of extensive research and numerous field tests over the past several years. This work has brought out both favorable and unfavorable features of the miscible recovery methods. Many tests have shown that a miscible fluid can displace all of the oil contacted, leaving no high residual oil saturation, as is characteristic of immiscible displacements. The miscible methods have proven dificult to control, however, as evidenced by early breakthrough of the displacing fluid and poor sweep efficiency in several field projects. It became apparent early in the investigation of miscible displacement that the development of improved techniques and better methods of control would be required to extend the range of applicability to any significant portion of our petroleum reservoirs. The purpose of this study was to consider the problem of designing miscible floods to obtain better performance. A performance calculation was used in conjunction with experimental studies to develop means of predicting and interpreting miscible floods and to explore possible methods of improving their efficiency. Two aspects of miscible floods were considered separately in this study and the results are presented in two parts. The first part concerns the manner in which the miscible front is displaced through the reservoir. In these calculations the condition of miscibility between the reservoir oil and the displacing fluid is assumed. In the second portion the distribution and utilization of the preinjected solvent in maintaining rniscibility is considered. This portion dealing with solvent utilization applies only to the enriched gas or LPG slug processes. CALCULATION METHOD AND EXPERIMENTAL STUDIES COMPUTATIONAL MODEL The calculations for expected reservoir performance are based upon the multi-strata concept of reservoir properties. The method assumes multiple, independent strata (no crossflow between strata) and explicitly includes variations in patterns, injectivity, areal sweep and displacement efficiency. Lateral variation in permeability within the strata (for example, directional permeability) may be considered in the calculations, provided the variations are similar in all strata. The calculations based on this model furnish the rates of injection and rates of production of both oil and the displacing fluid for the composite system of strata. To carry out calculations on the mathematical model described, information is required on the performance of the displacement process under consideration in a single stratum element of the pattern to be used. In particular, for a given pattern and displacement process, data are required relating injectivity and composition of the produced stream to the volume of fluid injected. Data on the variations in areal sweep must also be available if it is desired to track the areal sweeps in the multi-strata model. These data may be obtained from experimental work such as model studies or other suitable methods. This representation of reservoir properties is, of course, an approximation and may be inappropriate in some cases. But the representation is not an arbitrary one since most oil reservoirs are essentially successive layers of sediment with the net producing pay zone often comprising but a fraction of the gross formation thickness. The fact that permeabilities measured in the vertical direction are frequently but a fraction of the horizontal permeability adds some evidence to the validity of this model. This type cal-

Jan 1, 1965

By D. W. Frommer

Processing nonmagnetic taconites by selective flocculation-desliming and flotation requires large volumes of water. If impounded without treatment the effluents from these processes require excessively large areas for containment. Experiments conducted in the Bureau of Mines 900-lb-per hr pilot plant at the Twin Cities Metallurgy Research Center indicates that approximately 85% of the water needed to process Michigan nonmagnetic taconite could be reclaimed from the process itself. Water was reclaimed by the controlled addition of lime, sodium carbonate, and synthetic flocculant. As a result, turbidities were reduced to ?1000 ppm equivalent SiO2, while a Ca ion content of ?16 ppm was maintained in the finished effluent. Good-quality flotation concentrates were obtained with reclaimed water and, by means of some indirect comparisons, it can be concluded that the reuse of the water permits a savings of almost 2.0 lb per ton of NaOH, and probably as much as 0.25 lb per ton of fatty acid for total savings of 7.8-10.3 cents per ton of feed. These savings are nearly offset by an estimated chemical cost of 9.3[c] per ton for water treatment.

Jan 1, 1970

By V. R. Garfias

INTRODUCTION FOR a number of years the senior author has been interested in the various geologic and engineering problems involved in the development of the petroliferous districts of northeastern Mexico, having in a previous paper 1 endeavored to present a summarized statement of the information relating to the geology and soil resources of this region. Of the many interesting geologic phenomena, perhaps those which have been the object of more speculation relate to the igneous intrusions which, in places, have a controlling influence on the accumulation of oil in commercial quantities, a relationship which has been tentatively explained by various observers with as many interestingly different views. The authors of the present paper aim to record, in the course of a general discussion of the various viewpoints, some additional data, and present further tentative conclusions with a view to rounding out an up-to-date summary of the subject. The greater part of the area in question lies in the State of Vera Cruz, only a northwest fraction being in the State of San Luis Potosi. Vera Cruz is bounded on the north by the State of Tamaulipas, the northernmost of the Mexican States along the Gulf. The topography of the States of Tamaulipas and Vera Cruz and of Texas and Louisiana to the north, is controlled by the Gulf coastal plain which in northern Vera Cruz has an average width of about 60 miles, the transitional topography between that of the rugged flanks of the Sierra and the lowlands of the coast being made up of a series of terraces and irregular hills and valleys.

Jan 8, 1917

By Richard E. Chism

If internal commotion can be called life, the Mexicans have certainly lived more in the last seventy-five years than any other people. To the oppression of the Spanish viceroys succeeded the sanguinary tumults of the Revolution of Independence, after which the Supreme Congress bequeathed its heritage of uncertain power to the empire of Iturbide, the only one ever established by Americans upon American soil, with an American at its head. That shortlived reign mas followed by years of ceaseless, bloody, and, to the superficial observer, meaningless revolutions—the deeper political and ecclesiastical significance of which it is beyond the scope of this paper to discuss. Then came foreign intervention, the ill-fated Austrian's brief supremacy, and the final triumph of the patriot cause under rugged old Benito Juarez, who crowned the victory of arms by a series of reforms breaking forever the temporal power of the Church and ushering in the calmer era which has lasted from the first accession of Diaz to the present day. During all those troublous times, the revolutionary ocean, that rolled so deeply over all other relics of Spanish dominion, had left almost unaltered the ancient laws of Spain, still lifting themselves above the tide, like landmarks of a flooded world. Many of these laws were obsolete ; some were absurdly inadequate to the demands

Jan 1, 1886

By R. I. Jaffee, F. C. Holden, H. R. Ogden

ECENT papers dealing with the properties of unalloyed iodide titanium have been directed primarily at the determination of base-line properties for alloy investigations. Early work was limited to a few tests because of the limited availability of iodide titanium at the time. In the results of papers by Campbell et al.,1 Gonser and Litton,2 Jaffee and Campbell,3 inlay and Snyder,4 and Jaffee, Ogden, and Maykuth, data on mechanical properties are presented for unalloyed iodide titanium in the annealed and cold-worked conditions. Data are presented in this paper which show the effects of heat treatment on the structure and mechanical properties of commercially produced iodide titanium. Correlation is made between microstruc-tural variables and the mechanical properties. Experimental Procedures Melting Stock: The melting stock used was as-deposited iodide titanium, produced by New Jersey Zinc Co. The furnished analysis showed the following range of impurities: N, 0.004 to 0.008 pct; Mn, 0.005 to 0.013; Fe, 0.0035 to 0.025; Al, 0.013 to 0.015; Mo, 0.0015; Pb, 0.0045 to 0.0065; Cu, 0.0015 to 0.002; Sn, 0.001 to 0.01; Mg, 0.0015 to 0.002; and Ni, 0.003. Hydrogen content as determined by vacuum-fusion analysis was 0.0091 wt pct (0.44 atomic pct) after arc melting and fabrication. Nitrogen analysis on the arc-melted and fabricated titanium showed a content of less than 0.002 pct N. The average hardness of the furnished stock was Rf 70, or approximately 85 VHN. Melting Procedure: The as-deposited rods were rolled, sheared, and degreased in preparation for arc melting. The charge was arc-melted with a tungsten electrode in a water-cooled copper crucible under a positive pressure of high purity (99.96 pct) argon. The final ingot was approximately 2 in. in diameter and showed no increase in hardness over that of the initial stock. Fabrication: Heating for fabrication was done in air. It was begun by forging the ingot into a 3/4 in. diam rod, at an initial temperature of 1600°F. Scale was removed by sandblasting. The rod was then swaged to 1/4 in. diam at room temperature through a series of 20 dies, with approximately 10 pct reduction in area between each die. An anneal of 1 hr at 850 °C in air was given after the 1/2 in. die, such that the final cold reduction was 75 pct. Sections cut from this rod were used for test and microstructure specimens. Heat Treatment: Heat treatments were carried out in resistance tube furnaces with stainless-steel linings, under an atmosphere of gettered argon. As further protection against contamination, the specimens were packed in titanium turnings in a titanium sleeve. Control experiments have shown negligible hardness increases with this method, indicating that contamination from oxygen and nitrogen is slight. Three cooling rates were employed in this work; these have been designated as water quenching, argon cooling (to simulate air cooling under a controlled atmosphere), and furnace cooling. The cooling rate for an argon cool is 100°C per min for the first minute, with an average cooling rate of 35°C per min over a 15-min period. A furnace cool requires about 10 hr, with an average cooling rate of 3.6oC per min during the first hour, and an average cooling rate of 1.2°C per min over the 10-hr period. Microimpact Test: The specimen adopted was based on the cylindrical Izod Type Y specimen (ASTM, E23-41T). All dimensions were reduced to half scale, including the notch radius. Specifications are shown in Fig. 1. The specimen is held vertically in an adapter and broken as a cantilever beam. Impact tests were run on a constant-velocity (11.34 ft per sec) Tinius Olsen impact testing machine with a total available energy of 100 in.-lb. Tests were made to determine the correlation between this microimpact and the standard V-notch Charpy impact test. Curves showing impact energy as a function of temperature for both impact tests are plotted in Fig. 2. Transition temperatures, when they occur, are about the same for both impact tests. All three titanium-rich materials have the same conversion factor, 10. Tensile Testing: Tensile tests were conducted on Baldwin-Southwark testing machines using the 600, 2400, or 3000 1b range. Specifications for the test specimen were taken from the 1948 edition of the ASM Metals Handbook, and are shown in Fig. 1. Strain measurements were made using an SR-4 resistance gage (Type A-7) cemented to the reduced section in conjunction with a lever-type extenso-meter. Readings on the SR-4 strain indicator were

Jan 1, 1954

By W. L. Crentz, E. E. Donath, D. Doherty

Maurice Rey—The influence of cyclone diameter upon the fineness of separation is an important point which, however, cannot be discussed adequately if the injection pressure or the rate of flow are not specified. Perhaps some light can be thrown on the matter by using the formulas derived by Dahlstrom. Let us consider several geometrically similar cyclones where the apertures e and b are equal and proportional to the diameter D and which are operated with the same pressure drop. Eq 8 of Dahlstrom's paper can be written: Q Q = K D'. " or. if F is constant: Q = K D18 K is a constant of proportionality. Introducing this value of Q in eq 13 gives elimination efficiency = K D0' " Elimination efficiency, in the terminology of Dahlstrom, means the diameter of particles, in microns, which divide equally between the underflow and the overflow. This denomination is regrettable and it would be preferable to call it diameter of separation or characteristic size or any other name connoting a size rather than an efficiency. Whatever the name used, the above equation shows a slow increase in the fineness of separation when the diameter of the cyclone decreases. For example, if a 14-in. cyclone gives a 400-mesh separation (37 microns), geometrically similar cyclones, having the same pressure drop will give separations at the sizes shown below.

Jan 1, 1951

By E. E. Donath, W. L. Crentz, D. Doherty

Maurice Rey—The influence of cyclone diameter upon the fineness of separation is an important point which, however, cannot be discussed adequately if the injection pressure or the rate of flow are not specified. Perhaps some light can be thrown on the matter by using the formulas derived by Dahlstrom. Let us consider several geometrically similar cyclones where the apertures e and b are equal and proportional to the diameter D and which are operated with the same pressure drop. Eq 8 of Dahlstrom's paper can be written: Q Q = K D'. " or. if F is constant: Q = K D18 K is a constant of proportionality. Introducing this value of Q in eq 13 gives elimination efficiency = K D0' " Elimination efficiency, in the terminology of Dahlstrom, means the diameter of particles, in microns, which divide equally between the underflow and the overflow. This denomination is regrettable and it would be preferable to call it diameter of separation or characteristic size or any other name connoting a size rather than an efficiency. Whatever the name used, the above equation shows a slow increase in the fineness of separation when the diameter of the cyclone decreases. For example, if a 14-in. cyclone gives a 400-mesh separation (37 microns), geometrically similar cyclones, having the same pressure drop will give separations at the sizes shown below.

Jan 1, 1951

By John D. Weibmer

A remarkably simple construction system that derives its internal stability from metal straps buried in backfill is finding diverse mine applications, ranging from rock crusher headwalls to massive slot coal storage facilities. Reinforced Earth (Re/Earth), the system trade name of Reinforced Earth Co., is proving itself 20-50% less expensive than alternative earth embankment structures, and in the case of cast-in-place concrete walls, six to seven times faster to erect. While the majority of applications are in the realm of civil engineering-projects such as retaining walls, bridge abutments, slide buttresses, and containment dikes-a growing proportion is mine related. Of the estimated 120 Reinforced Earth projects that will be completed this year, company president David P. McKittrick expects mining to account for about 20% of the business volume.

Jan 8, 1978

By G. L. Oldright

DURING 1919, in the face of high cost for labor and supplies and a rapidly dropping copper market, the management of the Ohio Copper Co. of Utah was left with an orebody that had been shown to be very low grade, and a mill that could not make a satisfactory recovery, even by flotation, because a considerable proportion of the copper minerals was oxidized. About seven million tons had been mined by the use of a caving system, the best of the broken ore extracted and milled, and the nature and copper content of the rest of the orebody fairly well determined. The rock of the whole mine was shown to run between 0.3 and 1.3 per cent. in. copper. As, the Ohio Copper orebody lies at the contact of the original sandstone (now altered to quartzite) with the quartz monzonite intru-sion that was the source of the mineralization at Bingham Canon, the rock was thoroughly shattered. It was shown further that the rock was mostly quart-zite, with a few quartz-monzonite "fingers" projecting into it. Although some of the old cleavage planes had been healed by resilicification so as to leave some of the copper minerals disseminated in the rock, a large proportion of these minerals was distributed along the cleavage planes.

Jan 10, 1923

LINN BRADLEY, H.' D. EGBERT and W. W. STRONG (communication to the Secretary*).--In the discussion of the paper, a request was made for a further explanation of the curves given on Chart I. In preparing the curves given on this chart, a typical blast-furnace top gas having the following composition by weight was assumed: Per Cent. C02 21.00 CO 24.00 Hz 0.25 CH4 0:25 N2 54.50 For any given top-gas temperature, Curves A, B, C, D, and E indicate in British thermal units the sensible heat lost in cooling the top gas to 60° F. by wet-cleaning methods. Top-gas temperatures are plotted as abscissae, sensible heats above 60° F. in British thermal units are plotted as ordinates, and separate curves are drawn for top gases carrying various amounts of moisture. For any given stove exit-gas temperature, curves A1,-B1, C1, D1, and E1, indicate in British thermal units the sensible heat carried out of the stoves by the moisture which is left in the top gas when it is dry-cleaned and enters the stoves hot. This moisture is removed when the gases are wet-cleaned and the sensible heat which it carries out of the stoves is therefore saved. As before, separate curves are drawn for top gases carrying various amounts of moisture. The curves in Fig. 1, therefore, indicate graphically how much more sensible heat is conserved by cleaning the top gases by the dry-hot method than is conserved by cleaning the top. gases by a cold-wet method and thus removing the greater part of the moisture carried by them. They also show of how little moment it is from a heat conservation standpoint whether or not the moisture carried by the top gases is removed before they enter the stoves. That wet cleaning secures the removal of this moisture and is thus to be recommended from a heat conservation standpoint is an argument often advanced by advocates of wet cleaning. The curves of Fig. 1 show how fallacious such an argument is.

Jan 6, 1917

By Jonathan Ludlow, Paul J. Guay

Based on two studies that were funded by the U.S. Department of Energy, the authors provide an overview of the benefits expected from mining deeper webs on United States longwalls. The first study, completed in November 1979, identified the limits and potential gains from taking deeper webs with presently available equipment. The second on-going study discusses the conceptual design and benefits of a future system for taking very deep webs.

Jan 1, 1981

EUGENE WESLEY SHAW,* Washington, D. C. (written discussion ?).-Studies of the probable future production of oil wells and fields-particularly those in the nature of the recent work by Lewis and Beal, having the object of increasing the percentage of recovery-rank, in both practical and theoretic value, very high, if indeed they do not outrank all other petroleum investigations except structural surveys. Even such surveys, although saving untold millions that might have been spent in prospecting unpromising territory, may have less ultimate value than generally supposed, for it may perhaps be argued that much if not most of the condemned territory will sooner or later be tested-some is already productive-and the most that can be rightly claimed is the recovery of cream first; also that the consumption of the richest portions first cannot be extenuated, as it might with some resources, on the ground that if the best is not taken now it will deteriorate.

Jan 5, 1918

By C. Augustus Carlow

THE subject which has been allotted to me is so vast and far-reaching that it is impossible to deal adequately with it in the time available. A complete survey would occupy the spare time of any one man for many years, whereas the time available to me is measured in weeks In the circumstances, I have been fortunate in securing the aid of several willing collaborators, and shall endeavor to re present such information as presently exists in published form, examine the situation critically in the light of present-day conditions, and arrive at certain conclusions' which I shall venture to put forward for your consideration No one who has lived through the past 25 or 30 years, and who has witnessed the amazing achievements of recent scientific research, would venture to deny the possibility that new sources of energy-may yet become available, or to prophesy to what extent these may be harnessed to the service of mankind So far as we can see, however, coal, as a source not only of power and heat but also of that wonderful range of derivatives that form the raw materials of so many industrial processes, must continue to play a vital role in our economic life It is the chief mineral fuel, exceeding all other mineral resources in value, production and demand In value coal overshadows the industrial metals, while of the sources of energy-coal, oil, gas and water power-the first named is the most important Thus, for example, in the United States, coal as a fuel (that is, as a source of heat and power) is still predominant, the figures of percentage of

Jan 1, 1947

By A. W. Hann

THE importance, to geologists and metallurgists, of knowing the mineralogical forms in which the silver occurs in ores has increased during the past few years, and will continue to increase as long as working hypotheses are converted into proved theories and rule of thumb methods are supplanted by scientific data. The methods used for the determination of these silver minerals have been: (1) careful study of polished ore sections with the microscope, and more recently, (2) metallurgical separation of the ground ore by flotation, tabling and panning, supplemented by microscopic examination of these separated minerals, and chemical analyses. During the course of some experimental work carried on by the testing department of the International Smelting Co. and myself, it became important to determine, in a general way, the distribution of the silver values in the minerals, as they exist in Tintic Standard and North Lilly siliceous oxidized lead-silver ores. These mines are in the East Tintic Mining District, State of Utah. In this work the second method was used. Differential flotation tests were run, separating the sulfide from the oxidized minerals, and the products were assayed. Various concentrates were carefully panned and the separated products assayed; special samples of ore were selected and assayed. The microscope was used only for the purpose of determin; ing whether the individual minerals were in the so-called "free" state. Analysis of Tintic Ores These chemical and mineralogical determinations showed the silver to be present as native silver, argento jarosite, argentite, and combined or inherent in the tetrahedrite, chalcopyrite, galena, pyrite, cerussite, anglesite, mimetite, malachite, iron oxide and occluded in the quartz. Careful microscopic work would probably show other forms in small amounts, such as the halide silver minerals and some of the antimony sulfide combinations. The tabulation of the analyses of the various products (Table 1) shows no evidences of fixed ratios of silver to any particular base metal.

Jan 1, 1929

The paragraphs quoted, regarding Mr. Hoover's appointment as chairman of the newly organized food board of the United States, are taken from the editorial page, of the New York Times for April 13: ?The country is fortunate in commanding the services of Herbert C. Hoover as Chairman of the newly established Food Board. This is n, problem of first importance. Few realize the extent to which American food stuffs will enter into the decision of the war, and it is doubtful if it has occurred to many minds as yet that we shall have to deny ourselves what we have regarded as necessaries in order to keep our European allies supplied. " Mr. Hoover is one of the leading mining engineers of the country. At the outbreak of the war he put his private affairs aside to become the head of the American Commission for Relief in Belgium. He has had an experience that perhaps no other man has ever had, covering the raising of money and the purchase and distribution of supplies on a large scale; He has been brought into close relations with the neutrals and the belligerents on both sides. By them all he is recognized is one of the best executives brought to the fore by the mar. Mr. Hoover is in a position now to place abilities and experience at the service of his country. He will come back with comparative data that will enable him to measure resources and deficiencies accurately. This appointment gives renewed assurance of our Government's grasp of the problems of war and its resolve to apply, business principles to their solution."

Jan 5, 1917

By Arthur C. Simmons

The Pennsylvania-grade oil industry suffered a serious decline in 1938, which can be largely accounted for by the decrease in the use of lubricating oil. Production was considerably lower than in previous years and prices were very much lower. Operating profits undoubtedly were lower than the year 1933, for the average price of Bradford crude in 1938 was $1.898 as compared with $1.86 in 1933, and the difference in average price of $0.04 per barrel was more than offset by increased operating costs and taxes. Bradford Field Production in the Bradford field in the state of Pennsylvania averaged 36,759 bbl. per day in 1938 as compared with 41,300 bbl. in 1937. The decline in average daily production of 4541 bbl. can be attributed to low market price and pipe-line proration rather than to the actual physical capacity of the field. Pipe-line proration was in effect for the last eight months of the year and the daily average production per month fluctuated between a maximum of 41,852 bbl. per day in March 1938 and a minimum of 33,649 bbl. per day in November. Production figures for Bradford field have been corrected to include only the parts of the Bradford field that arc within the state of Pennsylvania, but the well-completion data for the Bradford field cannot be segregated and include those of the entire Bradford field, part of which is in Sew York state. Production from the Bradford field was obtained almost wholly by water-flooding and no radically new methods or practices occurred. Intensive research work was carried on both by individuals and companies and as a cpooperative enterprise, and minor improvements are gradually occurring in spacing, shooting, application of pressure and water conditions. Drilling Central and Southen Pennsylvania.—Pennsylvania production in central and southern Pennsylvania was obtained largely by air and gas repressuring together with the usual amount of natural production, and the repressuring operations in other than the Bradford field have not

Jan 1, 1939

By Arthur C. Simmons

The Pennsylvania-grade oil industry suffered a serious decline in 1938, which can be largely accounted for by the decrease in the use of lubricating oil. Production was considerably lower than in previous years and prices were very much lower. Operating profits undoubtedly were lower than the year 1933, for the average price of Bradford crude in 1938 was $1.898 as compared with $1.86 in 1933, and the difference in average price of $0.04 per barrel was more than offset by increased operating costs and taxes. Bradford Field Production in the Bradford field in the state of Pennsylvania averaged 36,759 bbl. per day in 1938 as compared with 41,300 bbl. in 1937. The decline in average daily production of 4541 bbl. can be attributed to low market price and pipe-line proration rather than to the actual physical capacity of the field. Pipe-line proration was in effect for the last eight months of the year and the daily average production per month fluctuated between a maximum of 41,852 bbl. per day in March 1938 and a minimum of 33,649 bbl. per day in November. Production figures for Bradford field have been corrected to include only the parts of the Bradford field that arc within the state of Pennsylvania, but the well-completion data for the Bradford field cannot be segregated and include those of the entire Bradford field, part of which is in Sew York state. Production from the Bradford field was obtained almost wholly by water-flooding and no radically new methods or practices occurred. Intensive research work was carried on both by individuals and companies and as a cpooperative enterprise, and minor improvements are gradually occurring in spacing, shooting, application of pressure and water conditions. Drilling Central and Southen Pennsylvania.—Pennsylvania production in central and southern Pennsylvania was obtained largely by air and gas repressuring together with the usual amount of natural production, and the repressuring operations in other than the Bradford field have not

Jan 1, 1939