Search Documents

By G. R. Speich

The age-hardening of Fe-18 to 21 pct Ni marten-sites containing small amounts of titanium, aluminum, copper, or molybdenum has been studied by hardness measurements, transmission electron microscopy, extraction replicas, and X-ray and electron diffraction. Electyon-probe microanaly-sis of the extracted precipitates was also performed. The effects of temperature and composition on the aging kinetics have been studied in detail for Fe-20 pctNi-Ti martensites. All the martensites hardened on aging at 400" to 500 "C with a single aging peak. In the Fe-20 pct Ni-Ti martensites hardening was associated with the formation of a fine dispersion of NisTi. No precipitation was observed in an Fe-21 pct Ni-2.6 pct A1 alloy, although the hardness increased from 327 to 545 Dph during aging at 500°C. Copper was precgitated from an Fe-20 pct Ni-10.7pct Cu alloy, at least during the later stages of age-hardening. Hardening in an Fe-18 pctNi-5pct Mo alloy was associated with the precipitation of an intemzetallic compound tentatively identified as NisMo. The formation of austenite and the recovery of the defect structure of the martensite occur simultaneously with the normal precipitation processes &ring aging of these alloys. THE age-hardening of substitutional iron-base martensites is an important subject for study since age-hardening is one of the principal means of strengthening the substitutional iron-base martensites in precipitation-hardening stainless steels1 and maraging steels.a~4 In contrast to Fe-C martensites, these martensites are relatively soft and ductile in the as-quenched condition, due to the low solid-solution hardening effect of the substitutional elements as compared to carbon. Also, these martensites are hardened by aging at low temperatures in contrast to Fe-C martensites which generally soften on tempering. Titanium and aluminum, singly or in combination, as well as copper and molybdenum, have been the principal alloying additions to stainless steels to obtain an age-hardening reaction.' Ti-A1 or Co-Mo-Ti combinations have been used in the case of maraging steels.3"4 The present work has been confined to a study of the age-hardening characteristics of an Fe-18 to 21 pct Ni martensite to which small amounts of titanium, aluminum, copper, and molybdenum were added in order to study the effects of each alloying element separately. The age-hardening characteristics of these alloys were studied by hardness measurements, transmission electron microscopy, extraction replicas, and X-ray and electron diffraction. Electron-probe micro-analysis of the extracted precipitates was also performed. The types and dispersion of precipitates, the formation of austenite, and the recovery of the defect structure of the martensite all were studied. EXPERIMENTAL PROCEDURE Alloys. The compositions of the alloys studied are listed in Table I. The level of 18 to 21 pct Ni was chosen to assure complete transformation to martensite on quenching and is the same nickel level used in maraging steels. The concentrations of titanium, aluminum, copper, and molybdenum were chosen after a study of the and Fe-Ni-MO' ternary diagrams indicated how much of each alloying element could be dissolved in austenite. Alloys with 2 and 4 pct Cu were also studied, but these did not show precipitation hardening at the nickel levels studied and will not be discussed further. The alloys were prepared from electrolytic iron and high-purity* nickel, titanium, aluminum, copper, and molybdenum by vacuum melting of 20-lb heats. These were vacuum-cast into two 8-lb ingots. The ingots were hot-rolled at 1100°C to 1/2-in. plate and subsequently cut into 3/8-in. cubes. The cubes were sealed in evacuated quartz capsules and solution-treated for 16 hr at 1100°C, except for the Fe-20 pct Ni-10.7 pct Cu alloy and Fe-21 pct Ni-2.6 pct A1 alloys which were solution-treated for 16 hr at 1300" and at 1250"C, respectively. Metallographic examina-

Jan 1, 1963

[ ]

Jan 12, 1959

By Lloyd Jones

THE strip industry made rapid strides in regard to both width and gage until about 1922, when the maximum width was about 20 in. In the hot mills, strips of thin gages in wide widths could be pro-duced, but only at a sacrifice of length of coil, con-siderable increase in power, and decreased tonnage out-put on the min. Hot mills, like the Bray sheet mill and the modern strip and skelp mills, demonstrated that . wider strip could readily be rolled, if such a product was desired. The strip manufacturers were really limited in width, not by the hot strip, but by the cold rolling of wide strip. This factor was roll pressure. The diameter of rolls increased as the width of strip increased. For cold rolling strip 20 in. wide, cold rolls were approximately 20 in. diameter. As the rolls became larger, the arc of contact between the rolls and the strip increased approximately, according to the formula, b=\/Rd where b = the width of contact R = roll radius d = total reduction Now the crushing strength of cold steel of low carbon varies from 70,000 to 100,000 lb. per sq. in. With each succeeding pass the crushing strength increases and may approach 250,000 lb., according to the total reduction. The total reduction in cold rolling of low-carbon steel will range from 40 to 70 per cent of the original thickness, usually in about three or four passes. On this basis, assuming a reduction of 20 per cent in one pass, the crushing strength of steel assumed at 120,000 lb., we have a total pressure between rolls, which (assuming that the rolls do not deform) equals: Roll Strip Strip Diameter, Width, Thickness, In. In. In. Pounds 10 10 0.100 380,000 20 20 0.100 1,080,000 30 36 0.100 2,375,000 42 50 0.100 3,900,000 These figures are approximate, but you will note that in increasing the width five times, or 50 in., the total pressure between the rolls increased approximately ten times. In other words, the pressure per inch of width increased from 38,000 to 78,000 lb. for the same per-centage of reduction.

Jan 3, 1928

By Robert Ammon

The milling practice at Mascot, at present, consists of dry crushing to % in., jigging, fine grinding, and flotation. The ore arrives at the mill from two mines, No. 1 mine shaft being located in the mill proper, and No. 2 mine shaft being situated about 2000 ft. east of the mill. No. 2 mine is served by a coarse-crushing plant and aerial tramway to the mill bins. In jigging the No. 2 mine ore, 50 per cent. of the mill feed is rejected by the jigs as a jig tailing ranging from 5/8 in. to 10 mesh; the balance of this ore, after removing a jig concentrate, is ground to flotation feed. In jigging No. 1 mine ore, approximately 80 per cent. of the mill feed is rejected as a coarse jig tailing, and the balance is ground to flotation feed without the removal of a jig concentrate. The difference in the treatment is due to the fact that No. 2 mine ore carries a higher content of zinc than that from No. 1 mine. Of the total concentrates produced, 30 per cent. is made on jigs and 70 per cent. by flotation. At present, 1350 tons of No. 2 ore and 800 tons of No. 1 ore are treated each 24 hours. The recoveries for a typical week are as follows: Heads.......................... 3.55 Jig concentrates................ 61.30 Jig tails......................... 0.80 Flotation concentrates........... 60.60 Flotation tails................... 0.09 Extraction..................... 86.50 The associated minerals are a straw-colored sphalerite, dolomite, calcite, pyrite, quartz, and a small amount of greenockite, which occurs as a stain and sometimes small crystals along with sphalerite, but is comparatively rare. Pyrite is present in small quantities, usually less than 0.5 per cent.; quartz occurs in bands a few inches thick. A complete analysis of the ore is as follows: PEr Cent. Per Cent. Calcium carbonate.............. 48.11 Zinc sulfide.................... 5.43 Magnesium carbonate........... 35.36 Cadmium sulfide............... Nil Silica.......................... 8.73 Lead sulfide................... Nil Alumina....................... 1.04 Iron oxide...................... 1.33 Total....................... 100.00

Jan 1, 1925

(Under this heading will be published notes sent to the Secretary of the Institute by members or other persons. ) Position in sales department is open for a mining engineer with experience in mine ventilation and possessing some knowledge of fan design; one competent to lay out ventilating systems to meet various conditions. No. 2. A large company manufacturing mining machinery has an opening in one of its Western agencies for a young mechanical engineer who has had some experience in designing along general machine shop lines, and who is familiar with cost systems. No. 3. A large university desires to secure a prominent metallurgist for a vacant professorship in metallurgy. No. 4. Opening at a mine in New Jersey for a technical graduate to begin work as chairman on the surveying squad. Salary $50 per month to start. No. 5.

Jan 11, 1913

By Chung Yu, Wang

CHINA can he roughly divided into three metallogenetic province: North China, the Yangtze Valley, and South China. In North China the old Pre-Cambrian schists and gneisses are represented by the abundance of quartz mines in which sporadic occurrences of copper, lead, zinc, gold, and silver are sometimes found in subordinate quantities. Along the Yangtze Valley and in Central China, extending eastward as far as Shantung, are found here and there intrusions of dioritic rocks, in which occur the famous contact deposits of iron ore, besides which minor quantities of copper. lead, and zinc are also found. In South China the igneous intrunsions are of granitoid type in which, or in the vicinity of which, occur in certain regions immense deposits of antimony, tungsten, tin, and mercury. Broadly speaking. most of the famous coal mines are now situated in regions north of the Yangtze River, in which occur also the sedimentary deposits of iron in contradistinction to the contact deposits of iron along the Yangtze Valley.

Jan 1, 1943

Meeting of May 22, 1914.-President Thayer. announced the appointment of the following Committee on Arrangements for the San Francisco meeting of 1915: Charles W. Merrill, Chairman; F. W. Bradley, Abbot A. Hanks, S. B. Christy, and H. C. Hoover. President Thayer announced the appointment of the following Committee on Organization for the Utah-Nevada Local Section: R. C. Gemmell, Chairman; C. D. Blood, Lafayette Hanchett, Ernest Gayford; Duncan MacVichie, and George W. Riter. The President of the Institute offered $100, to be known as the "President's Prize," to be used as prizes for the best papers submitted by members of the Affiliated Student Societies, to be divided as follows: First Prize, $50; Second Prize, $30; Third Prize, $20. A committee, consisting of J. F. Kemp, Chairman; W. L. Saunders, and T. T. Read, was appointed to report on the conditions to govern the award. The President announced the appointment of the Committee on Mining and Milling Methods, the personnel of which is shown on a subsequent page of this Bulletin. The following were appointed on the Advisory Committee to the U. S. Bureau of Standards, to represent the manufacture of the various non-ferrous metals as indicated: Copper, F. L. Antisell; Nickel, David H. Browne; Lead, H. O. Hofman; Aluminum, J. W. Richards; Zinc, G. C. Stone. It was voted to hold a meeting of the Institute under the auspices of, the Iron and Steel Committee, the Committee on Petroleum and Gas, and the Committee on Coal and Coke, in Pittsburg, Pa., Oct. 8, 9, and. 10, 1914.

Jan 7, 1914

Discussion of the paper of W. R. Shimer and F. O. Kichline, presented at the New York Meeting, October, 1913, and printed in Bulletin No. 81, September, 1913, pp. 2361 to 2377. ALLERTON S. CUSHMAN,* Washington, D. C.:-I have been much interested in Mr. Shimer's valuable contribution. The apparent fact that the oxides of certain metals which are not reduced by hydrogen per se, are reducible when the oxides are dissolved in iron in small quantity, is brought out for the first time, and is worthy of the careful attention of investigators. The Ledebur method has been subjected to considerable criticism, owing to the alleged fact that it did not measure the oxygen combined with impurities. Personally I have found the method extremely helpful in spite of the minute quantities of oxygen with which it deals. Mr. Shinier points out that the highest oxygen he obtained by over-blowing was 0.074 per cent., while the minimum quantity in a properly finished steel was in the neighborhood of 0.02 per cent. The Ledebur method is used as a constant check on the quality of heats made in practice under my direction. In dealing with a very pure commercial iron, we should expect to find and would find difficulty in galvanizing sheets made from a heat running 0.07 per cent. oxygen. In fact, we do not like to have the oxygen rise above 0.03 per cent. I am inclined to agree with the author that excessive oxygen leaves a bath of metal in a very short time, but nevertheless I believe it takes only a very little combined oxygen to begin to make its presence felt in the pickling and galvanizing department, when sheet metal is the product manufactured. As Mr. Shimer points out, the higher the carbon, the lower the oxygen danger, and it is partly for this reason that the manufacture of carbon-free metal in the open-hearth furnace has to be so very carefully watched and controlled from the furnace through to the finished product. It is quite possible that, there is a critical temperature of dissociation between iron and oxygen, although the critical points may vary in baths of different carbon content. Unfortunately, the accurate determination of the temperature of a molten bath at the time of pouring or teeming is a very difficult matter. For a long time I have been wishing that there were some reliable data which would indicate the effect of the tem-

Jan 12, 1913

By Howard Martens, Pol Duwez

XPERIMENTS were performed on a Cr-Fc alloy Econtaining 44.7 pet Cr in order to determine the heat evolved during the transformation of the a solid solution into the s phase, and the change in volume accompanying the transformation. Since previous measurements on the rate of formation of a from s indicated that the reaction was quite fast as soon as the equilibrium temperature of 820°C was exceeded by some 50°, standard thermal analysis experiments were performed on heating specimens of s at the rate of approximately 40°C per sec. A definite thermal arrest was observed at 870"C, Fig. 1. This result indicates that the reverse seaction of into a is exothermic. From the heating curve of Fig. 1, taking 15°C per sec as the heating rate in the neighborhood of the transformation, 2.4 sec as the time for transformation, and assuming that the specific heat of the alloy at 850°C is an average between iron and chromium, namely 9.5 cal per mol per "C, the latent heat of transformation is approximately 342 cal per mol. The order of magnitude of this latent heat was also obtained by comparing the heating curve of Fig. 1 with a similar curve obtained with pure iron under identical experimental conditions. It was found that the length of the thermal arrest for s was about 1.8 times as long as that for iron. Since the latent heat of the a to 7 iron transformation is 203 cal per mol1, 2 the latent heat of it to a would be 365 cal per mol, which is in relatively good agreement with the value determined from the heating curve. For the determination of volume change, thermal expansion curves were recorded using a specimen containing 44.7 pet Cr and completely transformed to cr by previous treatment. The curves were recorded at a rate of heating of about 4°C per min and at approximately 840°C a sharr, increase in length of about 0.08 pet took place. Fig. 2. It is therefore established that the specific volume of a near the transformation temperature is about 0.24 pet smaller than that of a, and consequently, when the s phase forms in an a matrix, it would tend to shrink away from the matrix. Since the s phase is known to be extremely brittle, these results offer an explanation for the microscopic cracks often observed in the a phase under the microscope. The results of this study are in qualitative agreement with previously published data on stainless steel 19-9DLa and on a Cr-Fe alloy containing 45 pet Cr.' The increase in density due to the transformation from n to s given in ref. 4 is 0.90 pet. These measurements, however, were made at room temperature. whereas the presently reported 0.24 pet is the change at the temperature at which the transformation takes place during heating. In the graph of Fig. 2, the percentage change in length that would be observed at room temperature is given by the length X, which is about 0.27 pet. This would correspond to 0.81 pet in volume change. Acknowledgment This work was done at the Jet Propulsion Laboratory, California Institute of Technology, under Contract No. DA-04-495-ORD-18 with the Army Ordnance Corps, Washington, D. C. The authors wish to thank this agency for permission to publish the results of this investigation. References I H. Klinkhardt: Measurements of True Specific Heats at High Temperatures. Annalen der Physik (1927) 84, pp. 167-200. - H. Esser and W. Runghardt: Influence of the Method, of Dctcrmination on the Measured Heat Content of Iron. Archtvo ffur Dct Eisenhiittenwesen 11934) 8, pp. 37-38. J. J. Gilman, P. K. Koh, and 0. Zmeskal. Delta Ferrite Formation and its influence on the Formation of Sigma in a Wrought Heat Resisting Steel. Trans. ASM 1 1949) 11, pp. 1371-1388. 1 J. M. Thomas: Discussion of ref. 3. Trans. ASM (1949) 41, pp. 3 390-1392.

Jan 1, 1957

By AIME AIME

ALTHOUGH the retiring Chairman of the Industrial Minerals Division, Charles Henry Behre, Jr., does not say "you all" he is a product of the deep South, since he was born at Atlanta, on March 16, 1896. At the Boy Scout age he moved to New Orleans, where his father owned an ice plant, which seems an intelligent business for that climate. Intelligence evidently runs in the family, for Charlie, as his friends call him, has one sister who is a professor of zoology and another who is a concert pianist. Charlie has no explanation of why, when he reached college age, he decided to go to the University of Wisconsin, other than something more than an ordinary boyish interest in science, and the reputation which Wisconsin then enjoyed. At Madison he fell under the influence of Eliot Blackwelder, chose paleontology as his objective, and transferred, at the end of his sophomore year, to the University of Chicago, where the paleontological panorama seemed more extensive. He took his B.S. there in 1918, and graduated into the U. S. Army, where he eventually became a Sergeant in the Medical Corps.

Jan 1, 1945

By R. W. Smith

There are many inconsistencies and gaps in available information concerning the mechanism whereby dodecylamine acts as a collector for quartz. The author compares the studies which have been made in correlating the contact angle with adsorption density on quartz over all pH ranges, and attempts to resolve some of the inconsistencies. In recent years much information has been obtained concerning the mechanism whereby dodecylamine acts as a collector for quartz. Fuerstenau,1 for ex- ample, has shown that adsorption density and zeta potential under some conditions, at least, can be correlated with contact angle and flotation rate. There appear, however, to be several inconsistencies and gaps in information available. One inconsistency involves trying to correlate contact angle with adsorption density on quartz over all pH ranges. Fuerstenau's correlation at a collector concentration of 4x10-5 moles per liter dodecylamine acetate and about pH 10 shows a contact angle of about 80 degrees occurring at approximately monolayer coverage. If Gaudin and Morrow's2 and Morrow's3 contact angle data for near neutrality (pH 6 to 7) are now compared with deBruyn's4,5 adsorption data on quartz in a similar pH range, it will be noticed that a contact angle of 38 to 40 degrees corresponds to complete monolayer coverage (at an amine concentration of approximately 10"3 molar). In fact even at an amine

Jan 1, 1963

By K. Reinhardt

The idea of burning blast-furnace gases directly in gas-engines, instead of under steam-boilers, as had previously been done, was first put into practice barely ten years ago, almost simultaneously in Great Britain, Germany and Belgium. The pioneers of this movement made their first experiments with small engines. After these experiments had given satisfactory results, and it had been shown that the thermal value of the poor blast-furnace gases, in spite of defective scrubbing, could with safety be directly transformed into mechanical work in the gas-engine, there very soon arose a considerable demand for gas-engines of large power, similar to the large steam-engines employed in metallurgical works. In face of these sudden requirements, the gas-engine builders were placed in a difficult position; for up to that time the gas-motor was considered as suitable for small engines only, and it was generally believed that the limit of size had been attained with 100 to 150 effective h.p. in a single cylinder. Manufacturers of gas-motors, however, did not underrate the advantages offered by this new field for their manufactures, and it so happened that in Germany the Berlin-Anhaltische Masch-inenbau-Gesellschaft, of Dessau, was the first to undertake the construction of a 600-h.p. two-cycle gas-engine, with two cylinders of the Oechelhauser-Junkers type, for the Hoerder Mining & Smelting Company. The engine was started in 1898, and, with a few improvements and alterations, is still working satisfactorily. This engine worked with astonishingly high effciency, considering the period. The builders were therefore

Jan 1, 1907

By Robin O. Williams

AN investigation has been made of the Ni-Cr system for the purpose of elucidating certain points, namely the nature of aging in both terminal solid solutions and the nature of the phase diagram. Information pertaining to solubilities and precipitation has been obtained. Experimentation Five alloys, Table I, were arc melted in a cold copper crucible using electrolytic chromium and car-bony1 nickel, both dry hydrogen treated. These 100 g buttons were homogenized 24 hr at 1300°C in dry hydrogen and air cooled. Powders were prepared by filing or pulverizing and subsequent heat treatment was done in vacuum or helium using titanium chips as a getter. Powder of —80 mesh was filed from the 60 pct Ni alloy quenched from 1000°C and was sealed in silica under vacuum using a 250 °C outgassing. After aging as indicated in Table I1 the lattice parameters were measured on the quenched samples using the standard cos" 6 extrapolation. These parameters are considered accurate to roughly 0.0001A. In all cases chromium lines of 2.8812 ± 0.0005Å at 30°C were found. Drastic quenching from sufficiently high temperatures produced very sharp body-centered-cubic lines in the first four alloys without indications of transformations. Temperatures to 1250°C were used. Solid samples less than 1/16 in. thick were quenched in water without transformation and the powders could be adequately quenched in small helium filled thin wall silica tubing using a water quench. For those powder samples which were quenched from the two phase field the relative intensity of the body-centered-cubic lines and the face-centered-cubic lines were estimated and extrapolated to give the indicated solubility data in Fig. 1. The data for the two higher alloys were somewhat limited, the plotted points being the lowest temperature where no nickel phase was found. Neither filing, abrading, pulverizing, nor cooling to —190°C produced any new diffraction lines for solid samples quenched from the single phase region, nor did the character of the body-centered-cubic lines change Single phase body-centered-cubic powders likewise did not change on cooling to —190°C. Also, samples which had some precipitation due to inadequate quenching showed no additional changes under these conditions. The first change apparent by X-ray diffraction form samples quenched almost fast enough to prevent precipitation was the diffuseness of the body-centered-cubic lines, particularly on the low angle side, For slower cooling rates the diffuse face-centered-cubic lines appeared. Work on the large grained castings showed profuse streaking through some of the Laue spots while oscillating patterns showed broad body-centered-cubic and face-cen-tered-cubic lines as well as some new lines. For the 23.6 pct Ni alloy the new lines corresponded to 2.16, 1.96, and 1.86A and were more similar in character to the face-centered-cubic lines than the body-centered-cubic lines. Samples which were air cooled gave only face-centered-cubic and body-centered-cubic lines which were still broad. One pattern indicated that face-centered-cubic (111) plane was parallel to a body-centered-cubic (110) plane. For those samples which were examined by light microscopy there were details which were not resolved. However, varied and beautiful structures were obtained. Fig. 2 is of an alloy quenched in a helium filled silica tube from the single phase region and shows particles associated apparently with dislocations which are arranged in low angle boundaries. Finer, general precipitation has also taken place within the grains. Figs. 3 to 5 show the variety of structures produced in these alloys on continuous cooling. It appears that there are four distinct modes of precipitation as evidenced by these, figures. Annealing these structures at higher tem-peratures in the two phase field gives structures as shown in Fig. 6, which shows nickel plates in the chromium matrix which reprecipitated nickel on a much finer scale of the final quench. Lower annealing temperatures and shorter times naturally give finer plates of the nickel-rich phase. Samples of the first four alloys were annealed for appreciable times between 900º and 1250°C and gave structures like Fig. 6. The relative amounts of the two phases were measured and extrapolated to give solubility data as indicated in Fig. 1. The point at 1250°C was deduced from data of Oxx.1 These and most of the other samples were checked for ferromagnetism but none was apparent. In fact, it appeared that the magnetic susceptibilities were not more than three times that for paramagnetic chromium. Discussion In Fig. 1 it is seen that the solubility of nickel in chromium can be represented by a slightly curved line on the usual log X vs 1/T plot, These data are believed to be accurate to roughly 5 to 10º. There is only fair agreement with the data of Taylor and

Jan 1, 1958

By John B. Hastings

Chief among the varied problems facing the mine-manager is that of vein-structure and origin, which is highly important as a guide to successful discovery and development. If metalliferous deposits can be traced to the intrusion of waters along definite lines, then is there something tangible for him to study. But when he is told by a geologist that metalliferous deposits are due to some other cause, like magmatic differentiation, while not perhaps discouraged, he is impressed with a vague sense of new worlds to be conquered. In 1897, while manager of the War Eagle mine at Rossland, B. C., where, previously, the ore-bodies had not been supposed to occur as veins, I suggested to visiting members of the Canadian Geological Survey that, perhaps, the structure of the pyrrhotite-bodies of that mine, which had been proved to occur along well-defined fractures, might throw some light on the similar deposits of Sudbury, then held to be basic aggregations from the original magma. Later investigation has at least provoked discussion of this last deduction, questioning its correctness and suggesting that, perhaps, the deposits are actual veins. The following extract from a paper by J. E. Spurr' is quoted, because it sets forth Mr. Spurr's theory of the quartz-occurrences of the Silver Peak mines, which will be discussed in this article. It also graphically describes the attendant geological features. "The Drinkwater group of mines, which is the most important part of the Blair gold properties, and which has produced practically all of the million dollars' worth of ore, as above stated, may be taken as typical of the gold-veins which, though widespread and numerons, show a wonderful similarity of character. On the surface two adjacent veins outcrop, the Crowning Glory and the

Jan 1, 1906

By Dennis K. Mortensen

The Role of the Operator The ultimate objective of any installation is to be able to accomplish the useful work that it was originally designed for. The operator needs a tool that he can both operate effectively and maintain efficiently. The overall design and subsequent installation of a comminution circuit should be a marriage of good engineering practice and practicality. Since the operator must operate and maintain his equipment, his input into the design and installation is vital to its ultimate success. The design of a crushing or grinding circuit is dependent upon many factors including flowsheet design, equipment selection, physical layout, space restrictions, climatic restrictions and considerations for future expansion. The operator must live on a day-to-day basis with the results of the final design and installation. The most satisfactory operation will result when the operator has a major input into each of the criteria that are used to define the final design and installation. The operator referred to is not only the mining company or organization that is having the installation built for its specific use but, more specifically, the person or persons that will actually be responsible for its daily operation and maintenance. Future references to the "operator" will include those individuals with that daily reponsibility. The operator's input into the installation of the circuit is of equal importance to his input into the design. The engineering organization which puts together all of the various design drawings for circuit installation is generally restricted to trying to get all of the details onto a multitude of 24" x 36" two dimensional drawings with a few isometric drawings thrown in. It's almost impossible to get all of the details of a final installation onto all of the drawings, and field modifications are necessary to make everything fit properly. In a multilevel installation, such as a grinding or crushing circuit, it is difficult to envision space requirements to adequately operate and maintain the various pieces of equipment simply by looking at a set o£ drawings. For some designs it is helpful to build a scale model so that a more realistic view of what the installation will look like can be seen. The scale model allows the operator to make whatever changes in design are needed to operate and maintain his equipment most effi-

Jan 1, 1982

By AIME AIME

On Nov. 11, 1909, M. Alexandre Pourcel, of Paris, France, upon the proposal of a large number of distinguished members, and the unanimous recommendation of the Council, was elected by the Board of Directors an Honorary Member of the Institute. M. Pourcel has devoted forty-three years to the metallurgy of iron and steel ; and the work which he did between thirty and forty years ago constitutes an important part of the founda¬tion of the practice of to-day. Among his striking contribu¬tions are : (1) his perfection, in 1869, of the manufacture of high-grade ferro-manganese in a carbon-lined open-hearth furnace, instead of the costly crucibles previously used; (2) his discovery, in 1874, of the method of making solid steel cast¬ings; (3) his manufacture, in 1875, of ferro-manganese and silico-spiegel in the blast-furnace; and (4) his anticipation, in 1875, of modern American blast-furnace practice, by the pro¬duction, in a very small furnace, of Bessemer pig containing 2.5 per cent. of silicon, from a burden yielding only 46 per cent. of iron, and with a consumption, per ton of pig, of only 1,8401b. of coke, containing 15 per cent. of ash. These brilliant pioneer achievements, together with his contributions to cur¬rent technical literature, won for him the Bessemer gold medal of the Iron and Steel Institute ; the great" medal of honor," which is the highest award of the French Society of Mineral Industry, and other gold medals, as well as the distinction of honorary membership of the Comité des Forges de France, which was conferred upon him in 1891. In recent years, M. Pourcel has been instrumental, as consulting engineer of the Société de Commentry-Fourchambault, at Decazeville, France, in an extraordinary development of the manufacture of special steels. The Invar plant, of this company, is said to make a greater variety of such steels (includ-

Dec 1, 1909

By John B. Hastings

CHIEF among the varied problems facing the mine-manager is that of vein-structure and origin, which is highly important as a guide to successful discovery and development. If metalliferous deposits can be traced to the intrusion of waters along definite lines, then is there something tangible for him to study. But when he is told by a geologist that metalliferous deposits are due to some other cause, like magmatic differentiation, while not perhaps discouraged, he is impressed with a vague sense of new worlds to be conquered. In 1897, while manager of the War Eagle mine at Rossland, B. C., where, previously, the ore-bodies had not been supposed to occur as veins, I suggested to visiting members of the Canadian Geological Survey that, perhaps, the structure of the pyrrhotite-bodies of that mine, which had been proved to occur along well-defined fractures, might throw some light on the similar deposits of Sudbury, then held to be basic aggregations from the original magma. Later investigation has at least provoked discussion of this last deduction, questioning its correctness and suggesting that, perhaps, the deposits are actual veins. The following extract from a paper by J. E. Spurr 1 is quoted, because it sets forth Mr. Spurr's theory of the quartz-occurrences of the Silver Peak mines, which will be discussed in this article. It also graphically describes the attendant geological features. '' The Drinkwater group of mines, which is the most important part of the Blair gold properties, and which has produced practically all of the million dollars' worth of ore, as above stated, may be taken as typical of the gold-veins which, though widespread and numerous, show a wonderful similarity of character. On the surface two adjacent veins outcrop, the Crowning Glory and the Drink-

Jan 1, 1913

By M. Van Weyenbergh, G. Van Esbroeck

THE copper mines of the Katanga region in the Belgian Congo lie along the same mineralized belt as those of Northern Rhodesia. There are two distinct types of deposits in that belt, the dolomitic and the quartzitic. In the dolomitic type the metallic minerals are found in a dolomitic limestone country rock. Through oxidation and enrichment,, large deposits of high-grade oxidized copper ores were formed, some of which are being worked by the Union Miniére du Haut Katanga. Such deposits are all in Katanga. The quartzitic deposits are found in Katanga and Northern Rhodesia. Here the primary mineralization occurred in sandstones and quartzites, in horizons stratigraphically lower than the dolomites. These rocks are not favorable to secondary enrichment and the oxidized zone is poorer than the sulphide zone, which alone contains the ore. There are also in Katanga a few ore-bearing veins. One of them is being worked in the Prince Leopold mine at Kipushi. PRINCE LEOPOLD MINE The Kipushi ore body fills a fault vein and invades the wall rocks more or less extensively by metasomatic replacement. The vein strikes north-northeast and south-southwest and dips to the west. The variable dip averages 60ºto a depth of 300 ft., and more uniformly 80º below 400 ft. In the upper section the average width is 200 ft. and below the width is about 150 ft. The length of the ore body is 2300 feet. The eastern side of the vein-the footwall-is dolomitic and contains irregular masses of ore sometimes extending 100 ft. or more from the main

Jan 1, 1939

By W. L. Austin

The advance made in recent times in this branch of metallurgy is indicated by the attention the subject is receiving from important American copper-producing companies. Reference to the files of publications devoted to the mining industry discloses that some 20 American companies are actively investigating the amenability of their ore, or other material, to leaching methods, and that plants of varying capacities up to 10,000 tons per day arc under construction or are projected. Several leaching works are in commercial operation. It has been frequently pointed out that no method of leaching is universally applicable, for the reason that each ore differs in some particular from apparently similar ore found elsewhere, and also because local conditions are rarely the same even where the ore closely approximates in character that being worked at some other point. For this reason the older companies are approaching the matter in a conservative manner, experimentally determining for themselves the salient features in each instance. In considering a leaching proposition three factors at once fix the attention: (1) disengaging the metal from mineralized forms in which it is found in nature; (2) recovering the metal in a commercial state after it has been dissolved; (3) the apparatus best adapted to carrying out the several operations. Bringing the Metal into Solution This feature.has been found to present no serious difficulties. Numerous solvents for copper are known, and it has been repeatedly demonstrated on a commercial scale that from 80 to 90 per cent. of the metal contained in an ore can be rapidly brought into solution. It is interesting to note, however, that all of the companies above referred to have selected sulphuric acid as the basis for a lixiviant. Where oxidized ore practically free from precious metals is treated simple leaching with

Jan 1, 1915

By AIME AIME

IT its annual meeting on Oct. 21 and 22, the Engineers' Council for Professional Development announced the selection of J. P. H. Perry. vice-president of the Turner Construction Co. and prominent civil engineer of New York City as its new Chairman. He succeeds C. F. Scott, who becomes Chairman of its Committee on Professional Recognition. S. L. Tyler, Secretary of the American Institute of Chemical Engineers, succeeds A. B. Parsons as ECPD Secretary. R. E. Doherty is Vice-chairman. C. E. Davies remains as Assistant Secretary, as do R. L. Sackett as Chairman of the Committee on Student Selection and Guidance, O. W. Eshhach as Chairman of the Committee on Engineering Training, and Karl T. Compton as Chairman of the Committee on Engineering Schools.

Jan 1, 1938