Search Documents

"The Washoe Smelter is situated about two miles east of the City of Anaconda. The smelter site includes about 240 acres and peculiarly adapts itself in topography to the efficient handling of material. By reason of its being on a hill side it is possible to make the level of delivery of the product of one building the level of the charge floor of the next succeeding one.THE ORES: The ore treated comes principally from the Butte district and is hauled by the Butte, Anaconda & Pacific railway, a distance of twenty-eight miles, in trains of fifty 50-ton bottom-dump cars to the railroad yards at East Anaconda. At this point these trains are• split up according to their destination,—that is, as to whether they go to the concentrator and sampling mill ore bins, or to the storage bins. In each case they are made up into trains of eight or sixteen cars, according to the size of engine to be used, and are carefully weighed before delivery to their respective bills.Some idea of the magnitude of the works may be obtained from the following figures:Amount of ore that can be treated in 24 hours…12,000 tonsLime rock from adjacent quarries…2,300 tonsCoke used…500 tonsCoal for reverberatory use…500 tonsCoal for power use…50 tonsWater, per minute, 35,000 gallons.Men employed in and around Anaconda, 3,000. Monthly payroll for above, $300,000.00."

Jan 1, 1913

By John E. Willson, Ben L. Seegmiller

A portable electronic instrument was designed and constructed to detect unknown stress magnitudes in rocks. The principle used to detect stress is based on the propagation velocity method. This method allows the stress in a rock subjected to a load of unknown magnitude to be determined, provided that the wave velocity-stress relationship for similar rock is known. This is accomplished by measuring the travel time of longitudinal mechanical waves passing between two points a set distance apart in a rock. The velocity of the wave is calculated and the stress determined from the wave velocity-stress relationship. If the sending and receiving transducer spacing is constant, a time vs. stress relationship rather than the velocity-stress relationship may be used. The method is nondestructive and tests can be made without drilling or otherwise disturbing the rocks. The first studies undertaken in the United States to determine stress in rocks using propagation velocity techniques were reported by Obert1,2 in 1939 and 1940. The Soviet Union first reported using propagation methods to study rock pressures in 1951.8 Success of the method led to the development of a pulse-type ultrasonic seismoscope4 in 1953. Using this instrument, Ivanov and Betaneli5,6 in 1963 succeeded in devising and testing under field conditions a method of investigating coal pillar stresses. In 1967 Osipova7 reported results of similar studies in the Nakhichevan salt mines. In France, Tincelin8 has used the propagation velocity method to study the stress distribution in iron ore pillars. Uhlmann9 has investigated stresses in salt and potash pillars in Germany, using velocity techniques. Determination of uniaxial stress by propagation velocity methods is limited to rocks which have readily detectable wave velocity-stress variations. The present stress detection instrument is restricted in application to rocks which have a velocity change under stress of at least 300 fps. Examples of rocks which meet this requirement are sandstones, coal, and possibly some limestones. Testing of this instrument was limited to a laboratory study and the results may or may not be indicative of what would be found in a field test. A program of field experiments to study the feasibility of using this instrument to determine mine pillar and tunnel stresses is in progress. Instrument Design The instrument has two main components: A probe and a control-display unit. The probe is a hand-held device to which two identical rodlike transducers are rigidly mounted. Coaxial cable connects the probe to the control-display unit which is mounted in an enclosed carrying case measuring 7 % x 9 x 13 in. The instrument is designed so it may be carried and operated by one man. Weight of the probe and enclosed control-display unit is approximately 20.1b. The probe consists of two transducers identical in construction. One transducer is used to convert electronic pulses to mechanical waves and transmit these waves into a rock. The other detects the transmitted waves in the rock and converts them back into electronic signals. The basic element in both transducers is a piezoelectric crystal. The crystal is a disk made of lead titanate zirconate and has a natural resonant frequency of 400 kHz ±1% in the thickness mode. A schematic of one of the two identical transducing elements is shown in [Fig. 1.] A spacing of 6 in. between sending and receiving transducers has been found to be most satisfactory. The control-display unit consists of a pulse generator and a 1-in. oscilloscope. Various electronic devices are used for the power supply, amplification, and calibration. The amplitude of the square wave from the pulse generator can be continuously varied between 0 and +20 vdc. Pulse width can be set at 1, 2, 3, or 4 µsec. The repetition rate of the pulse can have the following values: 50, 75, 100, 150, 200, 250, 300, 400, 500, 750, and 1000 Hz. The oscilloscope delay system allows the travel time of the longitudinal wave passing through a rock to be measured to an accuracy ±0.1 µsec in the range from 0 to 995 µsec. Fig. 2 is a schematic of the various electronic sections in the control-display unit. Laboratory Testing The first step in using the instrument is to develop a velocity-stress or a time-stress curve for the par-

Jan 1, 1972

By David C. Russell

The Department of the Interior used to be a quiet, noncontroversial, almost boring agency. It, after all is the fifth oldest of the Departments, and as an old line Federal agency it has studiously performed its preservation and resource management functions in a caretaker mode--though some would say more "undertaker" than "caretaker"--locking up the body and soul of America piece-by-piece. Yes, quiet, serene. That is until Jim Watt showed up. And we have all seen that version of Mt. Vesuvius which resulted--only it was the environmentalists who blew their tops. Ronald Reagan chose Jim Watt as Secretary of this fine old agency to prove that one-third of our Nation's land and over a billion acres on the Outer Continental Shelf can work for this Nation. At the foundation of President Reagan's charge to Secretary Watt is a belief in the tenets of the free enterprise system, and in the individual freedoms upon which this country was founded. There are those who don't share this belief in democracy and free enterprise, and those who believe this 205 year experiment called the United States of America will fail. Nikita Krushchev said "we will bury you"--obviously he didn't agree with our system. An Italian sociologist, Franco Ferrorotti, said bureaucratic stagnation will kill capitalism. Certainly we have all felt the ravages of bloated bureaucracies. Perhaps one indicator in the United States is the Federal Register, that daily compilation of Government's largesse. In 1970, 20,000 pages of the Federal Register were published. A decade later, in 1980, that volume had quadrupled to 80,000 pages. The Federal bureaucracy can stagnate from excessive budgets as well. The Interior Department spent $60 million on administering Federal coal leasing in 1981. That's nearly two bits a ton for every ton of coal leased in 1981. You wouldn't stay in business very long if your administrative overhead on inventory was that outrageous. But the pessimism of our critics is apparent from more than red tape and bloated budgets. For decades America has been fasting--consuming too little of America's wealth of minerals, subsisting instead on a diet heavily reliant upon mid-east oil, with little emphasis or concern for inventorying and developing domestic energy and mineral resources. Economics--yes. But short-term, short-sighted economics. Excessively dependent upon foreign imports, of oil, cobalt, chrome and other strategic minerals, the U.S. measures its time before another embargo--or fallen Shah, or Soviet manipulation, or Saudi shift, or, as we witnessed in Egypt, assassination--an untimely loss to mankind and efforts to bring peace to the troubled mid-east. These disruptions, in addition to their tragic human tolls, impair the free world's security. Huge chunks of the United States have been locked away in dozens of single land use categories in the name of conservation, with only the foggiest idea of what resources might be denied the American people-and this at a time of unacceptable levels of energy and strategic mineral imports. More than half and perhaps two-thirds of all Government-owned lands are totally withdrawn from or severely restricted to development under the mining and leasing laws. We must continue to rid Government of the overly zealous restraints which have been keeping us from drawing upon that which can help restore our economy and national security. When we assumed responsibility, the United States was dependent on foreign sources for about 40 percent of its oil. In 1981, our oil import bill was approximately $83 billion--nearly 17 times what it was in 1972. Our reliance on foreign sources for essential minerals is even more disturbing. We must look to other countries--some unfriendly, some unstable--for 22 of 36 strategically critical minerals. Yet the energy resources on federal lands which are owned by the American people could meet our needs for centuries if properly managed. Eighty-five percent of the crude oil yet to be discovered in America is likely to come from public lands, as will 40 percent of the natural gas, 35 percent of the coal, 80 percent of the oil shale, nearly all of the tar sands, and substantial portions of uranium and geothermal energy. Our vast hardrock-mineral wealth includes untapped deposits of essential elements we now import, such as chromium, copper, platinum, and cobalt. The obvious question is, if these abundant resources can help to revitalize our economic strength and to preserve our national security, why aren't we using them to better advantage? To a large extent, the answer can be found in past decisions to restrict public access to the federal estate, thus deferring to us or our successors the tough decisions that flow from Congress' mandate to provide for environmentally responsible development of America's energy and mineral treasures. Here is the legacy this Administration inherited: In January 1981, 7 years after the onset of the Mideast oil embargo: ---Less than 15 percent of federal onshore lands were under lease for oil and gas development; ---No oil and gas leases had been issued in Alaska for 15 years;

Jan 1, 1982

By Charles H. Fulton

(Cleveland Meeting, October, 1912.) I. INTRODUCTION. THERE are comparatively few accurate data on the melting-or the freezing-point temperature of metallurgical slays, or on related physical phenomena, such as fluidity near the melting-point, specific heat, latent heat, etc. With the exception of the work of H. 0. Hoffman,1 and some older work by R. Akerman, P. Gredt, and H. M. Howe, no information is available that is of direct interest to the metallurgist. Hofman's valuable work is the only one that refers to slags produced in the metallurgy of copper and lead. The classic work of J. H. L. Vogt,2 who views slays from the standpoint of physical mixtures (solutions in which the entities are minerals), has opened up a. new field in the study of slags, and has placed the investigation of such properties as melting-temperatures, etc., on a rational basis. The recent work of A. L. Day, E. T. Allen, and W. P. White, of the Carnegie Institution, at Washington, and of European investigators 3 on certain systems of silicate minerals confirms the value of the investigation of silicate series from this standpoint, and it is my aim to apply this method to metallurgical slaws, in order to gain exact data of value in metallurgy. The work recorded in the present paper is the result of an investigation of reverberatory-furnace slags made for a Western smelting company to determine exactly the influence of change in composition, within comparatively narrow limits, on the melting-point. For a general discussion concerning the mineralogical character of slaws and the principles on which this investigation is based, reference should be made to other work,4 for the subject is too large to be stated in this paper, except very briefly in the following outline 1 Trans., xxix., 682 (1899). 2 Die Silikatschmelzlösungen; I. Ueber die Mineralbildung in Silikatschmelzlösungen; II Ueber die Schmelzpunkt-Erniedrigung der Silikatschmelzlösungen (Christiania, 1903-04). 3 Doelter, Handbuch der Mlineralehevu:e (1911) 4 C. H. Fulton, Principles (of Metallurgy. Chapter viii., on Slags, p. 24.5 (1910).

Dec 1, 1912

By A. B. Young

THERE were produced in this country in 1923 probably in the neighborhood of 12,000 or 13,000 tons of refined and crude arsenic, by far the greater portion coming as a by product of smelting operations. Early this year copper smelters were producing arsenic at the rate of about 425 tons per month and lead smelters at the rate of 7;0 tons per month. During the entire eighteen years prior to 1919, there were produced in the United States only 47,000 tons of arsenic, which amounts to only 25 per cent. of the present output. The great increased demand has come about through the augmented use of arsenates as insecticides and arsenates as weed killers. In an extract from "Mineral Resources of the United States" on "Arsenic in 1922," Messrs. Heikes and Loughlin say, "The minimum possible demand for arsenic in 1923 was estimated at the end of 1922 to be about 13,000 tons, including 2000 tons for plate glass manufacturers, 3000 tons for lead arsenate, 3500 tons for calcium arsenate, 1500 tons for weed killers, 1200 tons for Paris green, 1000 tons for sheep dips and 750 tons for proprietary mixtures. More recent information, however, indicates twice as great a demand for calcium arsenate." The latter has found great use in the last three or four years as a weapon to combat the boll weevil pest of the southern cotton belt. ~t the present writing refined white arsenic is being quoted on the New York market at from 13)d c. to 1455 c. per Ib., while the average price during the eighteen-year period just mentioned was 4.8 c.

Jan 1, 1924

By Victor G. Hills

CONTRARY to what seems to be the general impression, the island of Cyprus was not named for the metal copper, but the reverse was the case. The origin of the name is entirely lost. The ancient city Kition, the birthplace of Zeno, is supposed to be the same as Kittim mentioned in Gen. x, 4; Jeremiah ii, 10 and Ezekiel xxvii, 6, and Josephus states that this name seems to have been applied to the city and also to the island itself. Cyprus is 50 miles off the coast of Asia Minor. The mountains on the mainland are plainly visible across the sea from where I write six miles from the shore of Morphou bay. It is 200 miles from Joppa the port of Jerusalem, and 250 from Port Said. The shape of the island is like a lizard, the tail pointing directly toward the old city of Antioch near the northeastern corner of the Mediterranean. The island was once heavily timbered. Among the great trees the cedars were said to even excel the famous cedars of Lebanon. The Odyssey refers to it as the "sweet smelling island" and makes other references. But the continual wars of every race and age completely stripped it of its timber, and for centuries it has been woefully barren. There are two ranges of mountains. One borders the north coast and runs out in a slim rocky ridge forming the "tail." The other occupies the southwestern part of the island, the highest point being Mt. Troodes 6600 ft. high, sometimes called Mt. Olympus. Whether or not it be the Mt. Olympus, anyway right around there the ancient gods and godesses frequently "started things." These peaks are in plain sight 10 miles south from where I live.

Jan 1, 1926

By C. E. Siebenthal

produce attractive and consequently more salable products. It would seem, however, that if solder and babbitt were cast in closed molds, just as good practical results would be obtained by the user, without his being able to give preference to solders of unnecessarily higher grade on account of their appearance. It would be hopeless for any one. manufacturer of solder to undertake a change of this kind, but if all manufacturers of solder agreed upon it, they would be able, in my opinion, to get the users of solder to take, and to approve by their practical tests, metals containing less tin than they have been accustomed to. The same is true with regard to babbitt metals. An illustration of how, in the use of an alloy, appearance sometimes is deceptive, is to be found in the case of what may be called intermediate grades of babbitt. I am thoroughly convinced that high-tin or high-lead babbitts are better than those containing both lead and tin with relatively high percentages of each. A high-tin babbitt should not contain more than about 10 per cent. of lead, and a high-lead babbitt should not contain more than 10 per cent. of tin, unless the percentage of antimony can be correspondingly increased. The intermediate babbitts, such as those that contain from 30 to 70 per cent. of lead or tin, may give nice appearing castings that flow easily, but they have not the serviceability of the high-lead or high-tin babbitts. Their hardness diminishes very rapidly as the temperature rises, and they have a relatively low softening point due to the eutectic components present. The Cadmium Supply of the united States* C. E. Siebenthal, † Washington., D. C.—From being one of the most maligned of metals—a veritable bugaboo—cadmium has almost overnight become respectable, though its slender claim to respectability rests almost wholly on the possibility of its substitution for tin. Preliminary to any campaign for such substitution, particularly for enforced substitution, the possible supply of cadmium should be determined as closely as possible; for that reason the statistical inquiry of which this paper embodies the results was undertaken. Production Cadmium is marketed in two forms, as metallic cadmium, in sticks or bars, and as cadmium sulfide, the pigment. The metal has found its greatest field of use in this country as a component of an easily fusible alloy that is used in automatic fire extinguishers. The sulfide is used to some extent in paints but chiefly to give color and luster to glass and porcelain. The metal was first made in this country by the Grasselli Chemical

Jan 1, 1919

By J. S. Owens, R. W. Marsden, J. W. Emanuelson, R. F. Werner, N. E. Walker

The iron ores of the Mesabi Range occur in a 340 to 750-foot thick, Precambrian cherty iron formation termed "taconite." For about 65 years, extensive natural iron ore bodies were mined, and the ores either shipped as a direct ore or processed by gravity methods to a shipping grade iron ore. Since 1956, magnetite taconite ores, occurring in magnetite-rich horizons in the Biwabik iron formation, have been commercially concentrated and agglomerated. The transition from natural ores to concentrating-grade ores is progressing rapidly so that, in the near future, a major percentage of the iron ore shipped from the Mesabi Range will be as iron ore pellets produced from taconite. Natural iron ores of the Mesabi Range occur in the Biwabik formation as trough ore bodies in elongated channels and as irregular and tabular deposits in fractured areas associated with faults and folds. Ore bodies range in size from a few thousand tons to hundreds of millions of tons and may occur in any part of the iron formation. In some areas of strong ore development, ore was formed from the hanging-wall argillite to the footwall quartzite. The natural ores and beneficiating-grade natural crude ores were formed by the oxidation of the iron minerals, magnetite, greenalite, stilpnomelane, minnesotaite, and siderite, to hematite and goethite and by the removal of much of the silica in the cherty quartz and in the associated silicates by leaching. The ores are believed to have formed by the oxidizing and leaching action of surface waters. Magnetite taconite ores occur as stratigraphic zones in the Biwabik formation where it contains sufficient magnetite to be concentrated profitably, by magnetic methods, to give a magnetite concentrate that is agglomerated into a high quality product. Unoxidized taconite has an extensive distribution away from and between channels of oxidation and leaching but only a part of the unoxidized taconite is of ore grade. Two general types of magnetite taconite ore occur: ( 1) magnetite taconite of the Main Mesabi Range, generally west of Mesaba, which is composed of magnetite associated with cherty quartz, greenalite, stilpnomelane, minnesotaite, and carbonates and (2) magnetite taconite of the Eastern Mesabi, generally east of Mesaba, composed of magnetite associated with quartz, cummingtonite, actinolite, ferrohypersthene, hedenbergite, fayalite, hornblende, pyroxene, garnet, and biotite. The Mesabi taconite is a metasediment derived from an iron- and silica-rich chemical sediment that has been regionally metamorphosed and, on the eastern end, additionally metamorphosed by the Duluth Gabbro Complex.

Jan 1, 1968

By R. H. Hadfield

Professor ArnolD, of the Sheffield Technical School, who has done so much excellent work in metallurgical research, recently produced, with the aid of aluminum, a sound ingot and bar from the purest known Swedish brand containing 99.8 per cent. of pure iron. Table 1. shows the physical quantities of this metal. TABLE I.— Tests of a Sample of Almost Pure Iron Prepared by Professor Arnold from D. v Ewedish Bar, Containing Before Fusion 0.04 Per Cent. of Carbon. I. II.+ III. Series mark,.. 136 1.371F ...... C, 0.07 0.07 Si, 0.04 0.04 8, 0.02 0.03 ...... Analysis, per cent,. .. P, 0.02 0.015 ...... Mn, 0.06 0.07 Al, 003 ............ Fe, 99.76 99.81 ...... Specific gravity,........... 7.863 ...... Original diameter, inches,. .. 0.564 0.798 0.798 Original area, square inches,. . 0.25 0.50 0.50 Limit of elasticity, tons per square inch,...... 18. 3.8 Breaking-load, tons per square inch,. 21. 23. 14.75 Total elongation, per cent., measured on 2 in.,...... 50. 49.25 61. Total reduction of area, per cent.,. 80. 69.60 61.20 Extension at permanent set, per cent.,...... 0.007 ...... silky and Appearance of fracture,. .. . silky i granular in parts.

Jan 1, 1894

By Ralph Sweetser

AT the joint session of Blast Furnace and Open Hearth Committees, April 7, 1937, at Birmingham, the subject of the quality of basic open-hearth pig iron was so well presented and discussed from so many different viewpoints that it was the general opinion that progress had been made and that such meetings were conducive to the advancement of the art of making pig iron of the right quality for the open-hearth man to produce the most satisfactory quality of steel. It was agreed that there is a decided differentiation between the chemical analysis of pig iron and the "quality" of pig iron. Paul J. McKim said that open-hearth furnace operators frequently make refer-ence to certain types of iron as "bad iron," "dirty iron," "cold metal,' etc., claiming that when using these irons, although they are within specified chemical analysis, it is impossible to produce quality steel. Mr. McKim gave a list of the suggested causes of those "certain types" of bad irons that have a thoroughly respectable analysis but a thoroughly disreputable character. Another open-hearth man, P. A. Maclsaac, of Nova Scotia, said that: The effects of iron flint is below standard in analysis or in that mysterious property called quality, are well known to all open-hearth operators. It has been shown that iron of this type results in the production of steels on which the rejections of finished product, run high. What is to be done about it? I would say that the burden of producing high-quality iron should be placed squarely on the shoulders of the blast-furnace man, even as that of making good steel is shouldered by the open-hearth luau. It is the purpose of this paper to bring out into the open this 'mysteri-ous property called quality"; that is, in those "certain types" of basic pig iron that make it impossible to produce quality steels; and at the same time to point the way for the blast-furnace man to be able to shoulder the burden that Mr. MacIsaac and all other open-hearth men and foundry-men have placed upon him.

Jan 1, 1938

By Franklin G. Pardee

IN 1920 the Minnesota Tax Commission estimated a reserve of 1,341,674,538 long tons of iron ore in Minnesota, the Michigan State Tax Commission report showed 199,092,855 long tons in reserve in that state, and the Wisconsin Geological Survey set the Wisconsin reserves at 21,500,000 long tons. The total reserve that year for the Lake Superior District amounted to 1,562,267,393 long tons. Ten years later the reserves of iron ore in these same districts were Minnesota 1,235,227,510, Michigan 168,349,823, and Wisconsin 23,000,000, or a total of 1,426,577,333 long tons. The decrease in ore reserves in this ten-year period was 135,690,060 long tons, but the shipments were 520,746,975 long tons. In other words, the ten-year depletion in reserves was only 8.68 per cent. If similar conditions carry into the future this calculation would indicate a life for the ore reserves of the Lake Superior region of over 100 years.

Jan 1, 1933

By M. E. Wadswort, A. S. Peck

Infrared data disclose that phenacite reacts with oleic acid to form a chemisorbed oleate monolayer on the mineral surface. The absorption band characteristic of the antisymmetrical C = 0 oleate structure appears at a spectral wavelength of 1623 cm-'. Chemisorption also results in the displacement of OH- and silicate from the mineral surface. Infrared absorbance at 1623 cm-1 is correlated with float-ability at different pH for -60-mesh phenacite particles. Phenacite, Be2SiO4, is an ore mineral often associated with quartz, microcline, and chrysoberyl in pegmatites and mica schist. Experimental phenacite beneficiating processes have been confined principally to the flotation of low grade ores occur-ing in several mountain ranges of Utah and Nevada. The U.S. Bureau of Mines ' has recently reported on the separation of phenacite from ore deposits of Mount Wheeler, Nev. Infrared techniques were previously applied by the authors to characterize the role of sodium oleate and oleic acid in the flotation of several non-sulfide minerals.23 A parallel study was projected to the flotation of the orthosilicate mineral phenacite with oleic acid. Infrared spectra provided a 'molecular fingerprint' of the mineral surface and permitted identification of the reaction mechanisms. Infrared data were complemented with flotation and chemical tests. EXPERIMENTAL PROCEDURES The experimental procedures used in this investigation, for which data are presented in graphical or spectral form, are described in chronological test order. Phenacite crystals from Mt. Antero, Colo., were obtained from Ward's Co., Monterey, Calif. The crystals were fragmented in a porcelain mortar to -60 mesh and then pretreated with 0.5 molar HC1 for 15 min to remove iron. Then, the mineral particles were washed free of acid with distilled water and dried. Part of the dried material was ground to a fine powder with a Fisher Grinder using an agate mortar and pestle. Next, the powder was placed in a graduated cylinder and mixed with 500 ml of distilled water. The mineral in suspension was decanted from the settled fraction after 5 min, and the colloidal suspension was used for adsorption tests in which a high specific mineral surface area was required for adsorption and infrared analysis. Conditioning was performed in 50 ml glass centrifuge tubes for both infrared and flotation test determinations. Twenty ml of colloidal suspension was used for the infrared adsorption tests. One and a half g of deslimed -60-mesh HCl pretreated phenacite was added to 20 ml of distilled water for flotation conditioning tests. Six mg of oleic acid was used for each infrared adsorption test, and 0.2 mg of oleic acid was used for the flotation conditioning tests. HCl and NaOH were used for pH modification. The pulps were stirred at a speed of about 1500 rpm for 3 min. Then, the solids were separated out and either dried at 50°C or immediately transferred to a float cell. The pH of the residual liquid was determined with a Beckman Zeromatic pH meter. The flotation procedure is described as follows: 1) A 325-1111 glass micro-float cell was filled with distilled water. 2) Conditioned mineral was placed in the cell and the pulp was aerated through the glass fritted bottom at 7 psi pressure. 3) Floated mineral was skimmed from the cell with a glass slide until flotation ceased. (The end point was reached in all tests in less than 2 min.) 4) The flotation products were dried, weighed, and the recovery was calculated. Samples for infrared analysis were made into mulls using either oleic acid or series 13-21 Halocarbon oil obtained from Halocarbon Products Corp., Hacken-sack, N.J. The mulls were placed between two sodium chloride windows. A characteristic phenacite infrared band at 1868 cm-' was used as an internal standard for quantitative determinations in which absorbance at this position was quantified by the baseline-tangent method4 and related to absorbance at 1623 cm-'. The ratio obtained by dividing absorbance at 1623 cm-' by absorbance at 1868 cm-' was defined as an absorbance quotient for use in graphical presentation.

Jan 1, 1968

By W. A. Forbes

OUR present-day geological surveys show that 36 of our States are underlain with bituminous coal, covering a total area of 496,709 square miles. The North American continent possesses 69 per cent of the world's coal reserves, with the United States alone having an estimated 55 per cent. The American coal reserves, in tons, are calculated to he about 3,500,000,000,000 tons, of which we have exhausted about 1 to 1 1/2 per cent. If this coal were mined at the rate of the 1918 production-a record output of 579;000,000 tons-it would not be depleted for 4,000 years. The more easily accessible and high-grade coals would obviously be consumed much before this; some estimates are 100 years. The natural progress of the nation's industries up to 1910 encouraged on every hand the development of new mines, especially where cheap and easy access to coal measures was coupled with short hauls to the consumer. Over-development resulted, which is perhaps today one of the fundamental causes for the many difficulties faced by the coal industry, which is highly competitive; about 70 per cent of the production cost is labor. Salient statistics for 1930, recently issued by the U. S. Bureau of Mines, follow:

Jan 1, 1932

By A. W. H. Morris, G. H. Laurie, J. N. Pratt

Using- galvanic cells of the form Sn(liq)/Sn" (LiCl-KC1-SnCl,)/Sn-Ag (alloy), measurements have been made of relative thermodynamic properties of the a, C, E, and liquid phases of the Ag-Sn alloy system. Partial heats of solution of the components in the liquid alloys lzave also been observed by direct cal-orimetric measurement in an isoperibol calorimeter. The thermodynanzic quantities are disczlssed in relation to structural and other properties and the existence of anomalous minor fluctuations in the partial heats and entropies of solution in liquid alloys is tentatively suggested. In the course of a recent electro motive-force study of the thermodynamic properties of Sn-Ag-Pd liquids,' some measurements were also performed on the Ag-Sn binary system. Most previous thermodynamic studies of this system have been concerned with the liquid state. Measurements confined to the limiting heat of solution of silver in liquid tin have been made by many calorimetric workers2 while high-temperature calorimetric measurements of the heats of formation of the full range of liquid alloys are reported in the early work of Kawakami~ (1323°K) and more recently by Wittig and Gehrin~(1248°K). Electromotive-force studies on liquid alloys have been made by Yanko, Drake, and Hovorka' (606" to 686°K; 86 to 99.4 at. pct Sn) and by Frantik and Mc Donald' (900°K; 30 to 90 at. pct Sn). The only known measurements on the solid state are of heats of formation of the a, £, and c phases; these values were obtained using tin-solution calorimetry, at 723"K, by Kleppa,~ whose investigation also yielded heats of formation of liquid alloys containing more than 64 at. pct Sn. The present experiments on the Ag-Sn alloys include a re-examination of the liquid phase and, because of the dearth of free-energy data for the solid state, attempted measurements on the a, c, and E phases. The principal new feature of electromotive-force results obtained for the liquid phase was an indication of anomalous fluctuations in the partial heats and entropies of solution of tin at certain compositions. However, since the values for these thermodynamic quantities were determined from the temperature coefficients of cell potentials, which are commonly subject to considerable error, confirmation by calorimetric measurements was considered desirable. A detailed investigation of the partial heats of solution of the components in the binary liquids was made using a liquid metal solution calorimeter. I) GALVANIC CELL STUDIES a) Experimental Details. Measurements were made, as a function of alloy composition and temperature, of the potentials of reversible galvanic cells of the form: ~n(liq)/~n++/~n-Ag (solid or liquid alloy) Details of the apparatus and experimental techniques have been given elsewhere.' so that a brief account will suffice here. Molten salt, 58 mole pct LiC1-42 mole pct KC1, containing small amounts (1 to 2 mole pct) of stannous chloride was used as the electrolyte. The salts were dehydrated by pre-electrolysis and vacuum -drying techniques. Cells were established under an argon atmosphere by immersing tin and alloy electrodes in the molten salt contained in a large silica tube, heated in a vertical resistance furnace. The tube was sealed at the top by a head plate provided with openings permitting the simultaneous insertion of six electrodes, a central thermocouple sheath, and connections to vacuum and argon lines. Temperatures were controlled to *0.2"C over prolonged periods, with maximum variation over the electrodes at any time of 0.l°C. Temperatures were measured with a standardized Pt/13 pct Rh-Pt couple. The electromotive force of this and the cell potentials were measured on a Cambridge Vernier potentiometer and short-period galvanometer. Alloys were prepared from Pass "S" tin (99.999 pct) and Johnson-Matthey high-purity silver (99.999 pct) by melting in evacuated silica capsules and quenching in cold water. For liquid phase experiments, pieces of the resulting alloys were remelted into prepared silica electrode units, while solid electrodes were prepared by remelting into 3-mm bore tubing, inserting a cleaned molybdenum lead wire, and quenching to produce uniform rods about 3 cm in length, with soundly attached leads. In all cases remelting was done under an argon atmosphere. The solid electrodes were subsequently annealed in evacu ated silica tubes for 14 days at about 20°C below the solidus and quenched. Analyses showed that these techniques produced uniform electrodes with no significant change from weighed out compositions. b) Results and Discussion. Measurements were made on about forty alloys in the solid and liquid states, over varying ranges of temperature between 550" and 1050°K. Stable, mutually consistent, and reproducible electromotive-force data were obtained with most liquid alloys and these are shown in Fig. 1. Investigations were extended below the liquidus tem-

Jan 1, 1967

By L. F. Reinartz

FROM the earliest times when our prehistoric ancestors laboriously fashioned crude tools and weapons from meteoric iron until our day when we manufacture steel in 150-ton open-hearth furnaces, the production of iron and steel has played a dramatic and important role in the development of civilization. Progress in the science of refining iron ore into iron and steel was painfully slow for many centuries. The keen scimitars of Damascus, the broadswords of the English knights, the coats of mail of French knights, and the Iron Pillar of Delhi are well¬known examples of medieval metallurgical technique. Expense and the scarcity of raw materials originally limited the distribution of iron and steel products. It was not until the nineteenth century that a determined effort was made to adapt the use of steel to peaceful pursuits. The spectacular and rapid strides made in the manufacture of steel during the last hundred years were hastened by the invention during the decade 1860 to 1870 of two great steelmaking processes-the Bessemer and the open-hearth process.

Jan 1, 1936

By C. E. LAWAL

WITH the object of adapting high-school vocational courses to the industrial needs of the community, a few high-school officials in West -Virginia working with the School of Mines of the State university decided to try an innovation this year. The purpose of this experiment was to teach coal mining in two high schools situated in mining communities. We thought that if a course in coal mining would be included in the list of optional courses offered in the high school, it might interest some of the boys, and if the course were properly taught it would undoubtedly be of inestimable value to those boys who later decided to take up mining work as their vocation. This coal-mining course was started last September in the Berwind and Gary high schools in West Virginia. The high-school officials in their conferences with' us decided that we should work up the outline of this course and they would assign the science teachers of the schools as instructors, with ,the understanding that we would help 'these instructors with this work. We consented to all this and submitted -an outline to the school officials which they are following this year.

Jan 1, 1929

By A. C. Butterworth

M OST operators of open-pit mines in the Lake Superior iron ore district are quite familiar with the use of fuel oil in the heavy-duty Diesel engines commonly used in truck-haulage service but some operators, including my own company, Pickands Mather, have had butane-engine trucks in service for several years, and less is known of their operation. One of the first installations of trucks for iron-ore haulage was in 1939 at a deep open-pit mine on the Cuyuna Range. These superseded standard-gauge steam haulage. Trucks then obtainable were equipped with 150-hp Diesel engines, and the speed of these units on an 8 % grade would have been so slow, considering the depth of the pit, that plans for an all-truck haul out of the pit were rejected. About this time one of the engine manufacturers brought out an auto-

Jan 1, 1948

By Samuel S. Wyer

THE installation of the gas-producer power-plant in America has been so unusual that all engineers have viewed it with in¬terest; a large majority, however, regard it with a lack of con-fidence and many with positive distrust. Despite the fact that European engineers have usually been less inclined to take the initiative along experimental lines than are Americans, they have, nevertheless, developed the gas-producer plant to a very high state of efficiency to which they were forced by the neces¬sity of economy in fuel-consumption. The gas-producer power-plant is so common in Europe that engineers as well as the general public regard it with the same degree of confidence that is now universally placed in steam¬plants. Gas-engines, both small and large, are in general use there, and central stations, aggregating several thousand horse¬power, are quite numerous. The fact that gas-producer power-plants have received so little attention in America may be attributed to five conditions:-1', ignorance and prejudice; 2, newness of work; 3, in-

Mar 1, 1905

By Julius Albert Krug

IN the field of mineral resources, today's problems and those we can reasonably expect in the future are so vast that nothing less than world-wide thinking and world-wide planning will suffice. I can imagine nothing more useful for the Institute to do in celebration of its seventy-fifth anniversary than to hold this conference on world mineral resources. Mineral resources are the basis of any nation's industrial production. Without expanding industrial production, the high standard of living found in the United States could not exist. Without such a standard of living it would be most unlikely that we should have a high level of culture. The hope of the world, as I see it, depends very largely on a general rise in living standards everywhere, and in the general increase of the levels of culture including a sympathetic understanding of the problems of other nations. For this reason, the proper use of the world's remaining mineral resources must be taken into account in any plans to safeguard the peace of the world. Being as exasperatingly human as human beings always seem to be,. we usually wait until almost too late to begin our plans to stave off an impending disaster. We do this as individuals, as components of particular States or Governments, and as citizens of the world. We waited, if not too late, certainly a very long time in getting started on the job of world-wide con-

Jan 1, 1947

By Henry D. Hibbard

I. INTRODUCTION. THESE impurities are perhaps the most important things in steel-especially steel made by the oxidation processes-the effect of which has not been at least approximately determined. By oxidation processes I mean the Bessemer and Siemens-Martin, during which the metalloids in the charge are removed by oxidation. It has been truly said that it is a clear advantage to have a new name for a new thing. To secure this and to economize space, let us adopt the name sonim (plural sonims) to designate the solid non-metallic impurities existing in steel or other metal. I would define a sonim as a solid non-metallic portion of matter existing as an impurity in metal. A piece of sand, brick, clay, or such material, imbedded in metal, would be considered as a foreign body, not as an impurity, and therefore not a sonim. The studies of sonims of which the results have been published hitherto, have been made chiefly or wholly on finished or at least on cold steel, without much, if any, regard to the specific methods by which the steel was made. While many of the results so obtained are valuable, they give little help in determining the cause, effect, or cure of the disease. It is not enough, in such a study, to know merely the commercial name of the process; for within the field of each process lies a great number of possible variations, each of which will yield a result differing in some respect from all others; and the control of sonims is particularly dependent. on the metallurgical treatment of the metal, because of the inability of analytical chemistry to throw much light on their presence, condition, and effect, as they usually occur in commercial steels. The microscope aids more, perhaps, than chemistry in their study.

Apr 1, 1911