Search Documents

By W. J. Carlson, I. lwasaki

Manganese and silica in nonmagnetic tailings from the direct reduction-magnetic separation step were so closely associated that no physical concentration methods were effective. Dilute sulfuric acid dissolved manganese and iron rapidly; manganese in the form of silicates was virtually insoluble in sulfuric acid solutions, thereby governing the maximum extraction attained by leaching. Autoclave leaching at elevated temperatures and at high oxygen pressures reduced the iron extraction to less than one tenth without affecting the manganese extraction. There was an indication that autoclaving solubilized the manganese silicates appreciably. Elimination of iron from leach solutions was carried out by aerating the solution in the pH range of 6.5-7; a platinum-calomel electrode pair provided a reliable indicator for the end point of iron removal. The purified leach solutions were free of interfering impurities for the recovery of manganese as metal, dioxide, or carbonate. Manganiferous iron ores of the Cuyuna Range, Minn., are too low in iron content to be directly useful as iron ores, and too low in manganese content to be termed manganese ores. Common methods of physical beneficiation such as gravity concentration and flotation have not been successful in upgrading this material. The R-N process, when applied to manganiferous iron ores,1'2 produces sponge iron by direct reduction of iron oxides, while leaving manganese as manganous oxide. From fine grinding and magnetic separation of the reduced ore, a tailing is produced which is relatively rich in manganese and low in iron content. The nonmagnetic tailing can readily be leached with acids and then further processed to recover manganese in various forms. In this way, two processes, neither of which would be an economic solution to the Cuyuna ore problem by itself, may be combined to produce two marketable products, thereby rendering the over-all process economically more attractive. This article reports on the results of a leaching study on the nonmagnetic tailings, both in a batch agitation vessel and in an autoclave; on the problems involved in the purification of leach liquors by aeration; and on the recovery techniques used to produce manganese metal by electrolysis, manganese dioxide either by electrolysis or by autoclaving, and

Jan 1, 1968

By C. E. Sims, G. A. Moore

In previous publications of the writers4-7 it has been shown that vacuum extraction of steel can be carried as close to quantitative completion as desired provided the steel is in the austenitic state and sufficiellt time is allowed. For precise work, the method claims preference because the equipmelit for holding and heating the sample can be made simple, and because crucibles, boats, and other unnecessary materials can be eliminated and the blanks thus made very small. It is well known that the evolution rate of hydrogen is smaller just above the trans. formation than immediately below, as would be expected from the increase in solubility when passing into the gamma state. Many attempts have been made to obtain analyses by extraction just below the transition, using times of approxi. mately 2 hr. while it is true that the rate of evolution drops nearly to zero under these conditions, it has repeatedly been shown that the process is incomplete since on raising the temperature into the austenitic range, evolution will be resumed, usually after a, considerable induction period. The low-temperature evolution process appears to be useful in some cases for comparative tests where the residual crror may be more or less constant between samples, For general use, however, there is no guarantee that the error caused by incomplete extraction is constant; hence, the more laborious but more reliable high-temPe'atu'e Process must be used. At high temperature, an original flash evolution, similar to that at lower temperature, is first observed. After not more than an hour, the flash subsides and cvolution settles down to a regular first-order reaction rate for which the half-life* is usually of the order of a few hours for the 5/8-in. diam cylinder at 1050°C. The regular evolution may be followed for whatever period appears justified, after which the residual gas may be estimated as equal to that which was evolved in the last observed half-life period. Tests have shown that the composition of the evolved gas does not vary greatly during the progress of evolution; therefore the residual gas may safely be taken to have the same composition as the portion col-

Jan 1, 1949

By L. J. Murphy

The production of crude oil in the United States is exceeding consumption by one-quarter million barrels per day and, with the possibilities of West Texas, this condition of overproduction, unless controlled, is likely to continue for some time. The resulting low price of oil has caused the operator to observe closely his lease operating costs. The installation of more efficient and reliable machinery has followed and it can well be said that the art of producing oil is on the threshold of a new era. In this advancement electricity has played a leading part. This paper covers only the problem of electricity as applied to lease operation and does not consider other phases of the industry, such as drilling and pipe-line pumping, in which electric power has been utilized economically. In considering electrification of pumping wells, the first question the operator asks is whether or not his costs will be reduced and the second question is whether or not the production will be increased. The third question, although in effect it is closely allied to the first, is the cost of power. The last question can be answered only after a thorough analysis of operating conditions and a study of the power rates prevailing in the particular field under consideration. Within the past few years, the power companies have realized the desirability of a steady 24-hr, pumping load, have made their rates for oil-field service particularly attractive, and in general have shown splendid cooperation in assisting the oil companies in the satisfactory application of electric power to their leases. When everything is taken into consideration, the first cost is practically the same for electric drive as for gas engines when pumping on the beam with individual motors. This cost, at prevailing prices, should aver-age approximately $2200 to $2400 per installation when using 15 to 35-hp., two-speed pumping equipment, including motor and control, countershaft, motor house, belt, installation charges, and a prorated portion of the cost of transmission lines and transformers for serving a number of wells. Since there is practically no difference in the cost of the two installations, it is evident that electricity, to justify its consideration, must have a lower operating cost or produce more oil.

Jan 1, 1928

By Harry T. Davis, Jasper L. Stuckley

The object of this paper is to record and interpret field and laboratory observations made by the writers during five years of study of the barite deposits of North Carolina. Deposits of barite are known to occur in three localities in North Carolina (Fig. 1) two of which—the Hot Springs and Kings Mountain —contain material of economic value. The Hot Springs area begins near Bluff, some 6 miles south of Hot Springs, and continues northeast by Stackhouse; a total length of 7 miles. The Kings Mountain deposits lie along a belt that extends from the north end of Crowders Mountain in a southwestward direction, along the east side of this and Kings Mountain, to Kings Creek, South Carolina. The third locality is 3½ miles southeast of Hillsboro, Orange County, a short distance west of the highway leading from Hillsboro to Chapel Hill. It is not known when barite was first discovered in North Carolina, but production from the Hot Springs area began some 50 years ago. The state has never produced large quantities of barite—usually there have been less than three producers—and definite figures are not available, but reasonably reliable estimates indicate a total production of 300,000 tons. From 1901 through 1920 barite mining was on a seemingly prosperous basis and a large tonnage was shipped from the Hot Springs and Kings Mountain areas. With the depression of 1920 the industry began to decline and production practically ceased in 1926. Geology of the Barite Areas In the Hot Springs area barite is found in the Max Patch granite of Archean age and the Snowbird formation of Cambrian age. The Max Patch granite is of two varieties, one gray to whitish and the other red. The gray granite is coarse, at times porphyritic, and composed of quartz, orthoclase and plagioclase feldspar, with a little biotite and muscovite. The red granite is also coarse and differs from the other only in having conspicuous pink and red feldspar. Both varieties have been much metamorphosed and weathered in places, so that they contain secondary

Jan 1, 1935

By Michael B. Bever, Carl F. Floe

The solubility of hydrogen in molten copper-tin alloys is of both practical and theoretical interest. From a practical standpoint, data on the equilibrium solubility as a function of temperature, pressure and alloy composition are valuable for a better understanding of porosity problems in bronze castings. From the theoretical point of view the determination of the hydrogen-copper-tin equilibrium is of interest since it extends the laws governing the solution of gases in metals. This paper presents the results of an investigation of the solubility of hydrogen in representative compositions of the copper-tin system at temperatures ranging from above the liquidus to I300°C. and at pressures from less than 50 mm. of mercury to about atmospheric. Review of Previous Work The solubility of hydrogen in copper was determined by Sieverts and Krumbhaarl in 1910 and by Roentgen and Moeller2 in 1934. Their values are in fair agreement. In 1926 Iwasé3 reported results that were very much higher. The published data on the solubility of hydrogen in tin do not agree. Smithells4 states that no reliable data are available According to Sieverts and Krumbhaar,5 hydrogen is insoluble in tin. Bircumshaw,6 on the other hand, found a definite solubility at 800°C. The latter's experimental procedure did not provide for stirring of the metal and in his opinion he failed to reach equilibrium. Iwasé3 again reported large solubility values. For copper alloys, Sieverts and Krumbhaar5 distinguished between alloying elements that do not markedly affect the solubility of hydrogen, elements that increase the solubility, and elements that reduce it. They named gold, tin, and aluminum as examples of this last group and reported hydrogen solubility data at 1225°C. for the copper-rich side of these alloy systems at atmospheric pressure. Without giving experimental results, they stated that the amount of hydrogen dissolved by liquid copper alloys is proportional to the square root of the pressure as in pure metals. These authors suggested that in a limited way the effect of an alloying element on the solubility of a gas is related to the constitution diagram for the alloy system. Sieverts7 also called attention to the fact that the curve of hydrogen solubility versus composition of copper-tin alloys shows a sharp change of direction at the composition of Cu3Sn and suggested that this compound persists at least to some extent in the molten state. Iwasé3 reported large hydrogen solubility values for several compositions of copper-tin alloys, which appear to be in error.

Jan 1, 1944

By C. W. Green-Halgh

The accuracy with which grade and tonnage of a mineral deposit may be calculated from diamond-drill assays is dependent upon: (1) the reliability of core and sludge samples and (2) the validity of methods used in grade and tonnage calculations. Limitations imposed by drilling and sampling preclude elaborate methods of computation. In adjusting core and sludge assays the importance assigned the core and sludge samples may be based on either the respective weights recovered or the respective volumes represented by each. Only when core and sludge recoveries arc poor do discrepancies between adjusted assays calculated by these two methods develop, in which case the "weight" method gives emphasis to the core sample and the "volume" method gives emphasis to the sludge sample. When the sludge suffers classification within the drill hole, the weight method gives more accurate results; when the sludge sample suffers no classification, the volume method gives more accurate results. Any drilling campaign offers a compromise between desired accuracy on the one hand and expediency, limited time, money. or facilities on the other. Since the determination of grade and tonnage is an approximation at best, a proper basis for their computation requires a knowledge of the limitations imposed by all phases of work upon which the calculations depend A rational basis for coordination of these phases of work requires determination of: (I) the degree of accuracy desired, as a function of the object of examination; (2) the degree of accuracy attainable, as a function of the limitations imposed in the drilling and sampling program; and (3) the validity of method to be used in calculating grade and tonnage from core and sludge assays. This paper presents results of a comparison made between two commonly used methods of adjusting core and sludge assays, the assumptions upon which these methods are based, and the interrelationship of the phases of work upon which these calculations are dependent. Object of Examination The Purpose of prospecting any mineral deposit is to secure sufficient samples from which Ore grade and tonnage may be calculated. Any mine examination, preliminary or formal, has a definite purpose, although its scope may be limited or broad. The type of examination to be conducted is dependent, therefore, 'pan the reason for instituting the investigation; its scope and thoroughness are directly related to economic considerations. It is highly desirable, therefore, that before starting a drilling campaign a complete understanding of the extent of examination and desired degree of accuracy be determined as a means of simplifying the drilling program and unifying the relative degree of

Jan 1, 1946

By Carl F. Floe, Michael B. Bever

The solubility of hydrogen in molten copper-tin alloys is of both practical and theoretical interest. From a practical standpoint, data on the equilibrium solubility as a function of temperature, pressure and alloy composition are valuable for a better understanding of porosity problems in bronze castings. From the theoretical point of view the determination of the hydrogen-copper-tin equilibrium is of interest since it extends the laws governing the solution of gases in metals. This paper presents the results of an investigation of the solubility of hydrogen in representative compositions of the copper-tin system at temperatures ranging from above the liquidus to I300°C. and at pressures from less than 50 mm. of mercury to about atmospheric. Review of Previous Work The solubility of hydrogen in copper was determined by Sieverts and Krumbhaarl in 1910 and by Roentgen and Moeller2 in 1934. Their values are in fair agreement. In 1926 Iwasé3 reported results that were very much higher. The published data on the solubility of hydrogen in tin do not agree. Smithells4 states that no reliable data are available According to Sieverts and Krumbhaar,5 hydrogen is insoluble in tin. Bircumshaw,6 on the other hand, found a definite solubility at 800°C. The latter's experimental procedure did not provide for stirring of the metal and in his opinion he failed to reach equilibrium. Iwasé3 again reported large solubility values. For copper alloys, Sieverts and Krumbhaar5 distinguished between alloying elements that do not markedly affect the solubility of hydrogen, elements that increase the solubility, and elements that reduce it. They named gold, tin, and aluminum as examples of this last group and reported hydrogen solubility data at 1225°C. for the copper-rich side of these alloy systems at atmospheric pressure. Without giving experimental results, they stated that the amount of hydrogen dissolved by liquid copper alloys is proportional to the square root of the pressure as in pure metals. These authors suggested that in a limited way the effect of an alloying element on the solubility of a gas is related to the constitution diagram for the alloy system. Sieverts7 also called attention to the fact that the curve of hydrogen solubility versus composition of copper-tin alloys shows a sharp change of direction at the composition of Cu3Sn and suggested that this compound persists at least to some extent in the molten state. Iwasé3 reported large hydrogen solubility values for several compositions of copper-tin alloys, which appear to be in error.

Jan 1, 1944

By L. D. Wooddy, Robert Moscrip

The simultaneous solution of the volumerric balance and the unsteady-state equation has been used for several years to make performance calculations for combination drive reservoirs. This method makes possible the calculation of volumetric changes of fluids in the gas cap, oil zone, and aquifer which occur as a result of withdrawals and reservoir pressure changes. It does not provide a means for the determination of reservoir fluid distribution changes corresponding to these vollrmetric changes. A knowledge of the fluid saturation distribution in the reservoir at various stages of depletion is important for the determination of the efficiency of gas and water as oil-displacement media and, therefore, for the reliable predicrion of ultimate oil recovery. To provide this knowledge, the displacement equations are solved simultaneously with the volumetric balance and unsteady-state equations. The described calculation procedure has been used satisfactorily to analyze the past performance and to predict the future behavior of combination drive reservoirs under both primary and pressure-maintenance operations. INTRODUCTION The three basic mechanisms by which oil is displaced from a reservoir are: (1) dissolved gas drive—the displacement of oil by the expansion of liberated solution gas, (2) water drive—the displacement of oil by water which enters the oil zone from the aquifer, and (3) gas cap drive—the displacement of oil by gas which ex- pands into the oil zone from the gas cap. The action of gravitational forces may be effective in increasing the efficiency of the basic drive mechanisms. Gravitational forces favor the segregation both of gas and oil and of oil and water, thus tending to shorten the transition zone between oil and displacing fluids. Most reservoirs produce under the influence of a combination of these drives and are designated "combination drive reservoirs". Fig. 1 is a cross section of a typical combination drive reservoir. A calculation procedure for analyzing the performance of combination drive reservoirs has been developed by combining the displacement equations' with the volumetric balance equation' and the unsteady-state equations. The pressure-production performance and the positions of the gas-oil and oil-water contacts are calculated for several stages of reservoir depletion by solving these equations simultaneously, thus affording a basis for: 1. Determining instantaneous and ultimate oil, gas, and water production under various operating conditions. 2. 'Establishing a maximum efficient rate of production, 3. Determining the advantages of pressure maintenance and unitization, and 4. Designing surface installations necessary for primarv and pressure-maintenance operations. DEFINITIONS The calculation procedure for combination drive res-

Jan 1, 1957

By Paul Averitt

The U. S. Geological Survey has been actively engaged in work on coal for more than 50 years. During this long period we have released more than 300 publications containing information about coal and coal reserves, including details on the thickness, distribution, and quality of coal, and the structure and stratigraphy of the coal-bearing rocks. We have also cooperated with state surveys on many similar publications. For many areas these reports are the only reliable published data on our resources of coal. During the last several years we have substantially increased our activities above the wartime low. We now have field work in progress, or reports in preparation, on 13 detailed mapping projects distributed as follows: 1. Pennsylvania anthracite field 2. Casselman Basin, Md. 3. Leslie County, Ky. 4. Deep River field, N. C. 5. Coosa field, Ala. 6. Powder River field, Mont. 7. Spotted Horse field, Wyo. 8. Yampa field, Colo. 9. Paonia field, Colo. 10. Trinidad field, Colo. 11. Durango field, Colo. 12. Chaco River area, N. M. 13. Lewis and Thurston County fields, Wash. For two of these areas; the Paonia field, Colo., and the Coosa field, Ala., we have published recently preliminary reports, and final reports are in preparation. In addition, we are nearing completion of a coal reserve study of Montana, and are beginning similar studies in several other states, as part of a program of revising our estimate of national coal resources on the basis of presently available data. Factors Involved in Making Estimates Our responsibilities include detailed field mapping to secure information on areas of outcrop of coal beds, their range in thickness, nature of roof rock, amount of overburden, correlation of the beds, stratigraphy and structure of the coal-bearing rocks, and the preparation of coal reserve figures based on these data. The computation and estimation of resources of coal in the ground, like that of resources of other mineral commodities, involves consideration of many additional purely geological factors that can be appraised best through such regional studies. Regional variations in the thickness and texture of rocks overlying and underlying coal beds, for example, give evidence as to the probable position of the edges of the basin of coal deposition, or may aid in the delineation of sand-filled channels that sometimes cut out coal beds. It is apparent that the detailed field studies, in which data are gathered, are the basis for coal reserve studies, and in our present program these two phases of work are being carried on together. Previous Coal Reserve Estimates For many years we have been aware

Jan 1, 1950

By R. I. Jaffee, R. W. Wood, H. R. Ogden, D. N. Williams

D. W. Morgan, D. H. Polonis,and R Taggart (Uuivevsity of Washington)—Dispersion hardening in titanium-copper alloys is of particular interest to us in view of our current research activities in phase transformations in this system. We should like to raise questions concerning several points in the paper. The flow sheet for fabrication and heat treatment (Authors' Fig. 2) indicates that 0.045 in sheet is treated in air for a period of 30 min at 1625' F. Were any surface coatings used to reduce oxygen contamination at this stage? One might ask the same question about the 8-hr annealing at 1400F. Contamination during fabrication and heat treatment of such thin sections could be considerable without some protection. Although the authors state that no analyses were made, they note that contamination masks the distinction between base strengths of the different alloys. In this connection, what fabrication and heat-treatment procedures were used in obtaining the comparison specimens of unalloyed titanium? It would seem that oxygen contamination must cast doubt on the reliability of the proposed strength-mean free path relationship deduced from the data (Authors' Fig. 5). It is usual to evaluate dispersion hardening on the basis of yield strength rather than ultimate tensile strength, and accordingly we have replotted the authors' Fig. 1 to include yield strength. The yield strength data do not justify a discontinuity of 3 p at either 70" or 1000 OF. Can the authors substantiate their conclusion 1) with additional evidence? Otherwise it seems that they have succeeded only in pointing out the possibility of a linear relationship between yield strength (or Uts) and the logarithm of the nleall free path, comparable with that demonstrated for iron-carbon alloys (Authors' Ref. 2). Work in our own laboratories has shown that the hardness of the phase Ti,Cu is 235 Vpn, and that of a 1.5 pct (at.) (2 pct wt) supersaturated solid solution of copper in titanium is 190 Vpn. This small difference in hardness would suggest that Ti2Cu should not be a very effective dispersion-hardening phase. D. N. Williams, R. W. Wood, H. R Ogden, RI. L Jaffee (authors' reply)— This discussion brings out some interesting points with respect to the interpretation of our results, and also raises some questions regarding the experimental technique. We shall consider the latter questions first. Contamination during heat treatment was prevented by performing all heat treatments in argon-filled Vycor capsules. Fabrication was done in air, with the usually observed scaling. Scale was removed

Jan 1, 1962

By K. L. Clark, Nicholas Kowall

MAXIMUM furnace efficiency and close control of final steel composition demand that the steel melter be able to follow closely the variations in the carbon content of the bath. For many years, the fracture test has been used by melters for estimating carbon, because it requires only a very short time to pour a sample into a chill mold, cool it in water, break it with a sledge hammer, and observe the fracture. After long experience gained from the observation of such fractures, most melters are able to estimate the carbon content of steel with amazing accuracy, particularly in the lower carbon ranges. Notwithstanding the utility of the fracture test, there has been widespread interest in other methods for rapid carbon determination to supplement it and to ensure against possible errors in human judgment. Several methods, based upon measurement of magnetic properties as functions of carbon content, have been described in the literature1-6 and have been found to give reasonably reliable results in plant practice when scrap composition is known and controlled. A difficulty encountered in the use of analyzers of the magnetic type is that alloying elements do change the relationship between carbon content and magnetic properties and it becomes necessary to establish calibration curves for all the expected combinations of alloy residuals that are not oxidized in the bath. The work reported here is of an investigation of a method that is independent of alloying elements normally present in constructional steels, being based upon the relatively well-known fact that in plain carbon and low-alloy steels martensitic hardness is a function of carbon content alone. WORK OF OTHER INVESTIGATORS In 1938, Burns, Moore and Archer published a curve7 that showed that the hardness of martensite is a function of carbon from 0.10 to 0.50 per cent and is independent of grain size or alloy content, at least within the range found in constructional S.A.E. compositions. Some of the deeper hardening types investigated, however, contained carbon to a maximum of only 0.20 per cent. Using this principle, Kern8 developed a method of rapid carbon determination for S.A.E. 43xx steels. His procedure consisted of chill-casting a test bar that was large enough to give a surface that could be prepared for Brinell indentations. The test piece was quenched immediately after solidification was complete and hardness readings were taken, so that the carbon content could be read from an experimentally determined curve giving the relationship between as-quenched hardness and carbon. EXPERIMENTAL WORK Although Kern's work had been done with a relatively deep-hardening steel, it

Jan 1, 1944

By W. C. Hagel

Previous inuestigators have repovted unusually low H* and Do values for self-dzf@szon in certazn bcc metals, e.g., chromium nnd y -uvanium. It has been postulated that this is nn experimental crl -tetion for the existpnce of a four -atom ring meclzanzsm, mid there could be. zmpovtant theoretrcal Implicatlons. By utilizing a precise sectioning technique with Cr51 as the tracer, self-dzffi-lsion measurements in large grains of 99.99-pct Cr were extended from 1200° fo 1600"C. A least- squares analysis of the data yields that D 0.280 exp (-73,20U/RT) cm2 sec-'. These AH* and Do unlues are not anomalous; there is little reason to believe that n vacancy mechanism is not opevatiue. Apparent differences at lower temperatures may result from preferential diffusion along short-circuititing paths and/or sample contamination. WITH continued technological effort, chromium and chromium-base alloys should ultimately become useful high-temperature structural materials. Accurate measurements of self-diffusion coefficients in the pure metal are necessary for a quantitative understanding of sintering, grain growth, creep, and other related rate processes. However, two conflicting determinations have been reported.* Using an Since careful diffusion studies normally yield Do values ranging from 0.1 to 10 cm2 sec-l, the Paxton-Gondolf results require independent experimental corroboration before an undue amount of speculation arises to explain the apparent anomaly. As discussed by Nowick6 and clearly shown by Hoffman and Turn-bull7 for self-diffusion in silver, a low AH* and Do can arise from preferential diffusion along grain boundaries or other short-circuiting paths. The most reliable data come from high-temperature measurements where volume effects predominate. Following a precise sectioning technique developed for determining silver diffusion in the intermetallic compound AgMg8 and cation diffusion in the corundum oxide Cr2O3,9 the purpose of this study was to measure true volume diffusion in high-purity, large-grain samples at higher temperatures than considered previously. Another point of interest is the frequent proposal10-12 that chromium undergoes an allotropic transformation between 1375" and 1800°C where the diffusion data might then show a discontinuity. I EXPERIMENTAL 1) Sample Preparation. The highest purity (99.997 pet) Cr currently available is produced by reduction of chromium tri-iodide. Three pounds of the resulting crystal bar were shipped in a sealed container with a complete chemical analysis from the vendor.* In conformity with the procedure used for

Jan 1, 1962

By Carl F. Floe, Michael B. Bever

TRE solubility of hydrogen in molten copper-tin alloys is of both practical and theoretical interest. From a practical standpoint, data on the equilibrium solubility as a function of temperature, pressure and alloy composition are valuable for a better understanding of porosity problems in bronze castings. From the theoretical point of view the determination of the hydrogen-copper-tin equilibrium is of interest since it extends the laws governing the solution of gases in metals. This paper presents the results of an investigation of the solubility of hydrogen in representative compositions of the copper-tin system at temperatures ranging from above the liquidus to 1300°C. and at pressures from less than 50 mm. of mercury to about atmospheric. REVIEW OF PREVIOUS WORK The solubility of hydrogen in copper was determined by Sieverts and Krumbhaarl in 1910 and by Roentgen and Moeller2 in 1934. Their values are in fair agreement. In 1926 Iwasé3 reported results that were very much higher. The published data on the solubility of hydrogen in tin do not agree. Smithells4 states that no reliable data are available. According to Sieverts and Krumbhaar,5 hydrogen is insoluble in tin. Bircumshaw,6 on the other hand, found a definite solubility at 800°C. The latter's experimental procedure did not provide for stirring of the metal and in his opinion he failed to reach equilibrium. Iwasé3 again reported large solubility values. For copper alloys, Sieverts and Krumbhaar6 distinguished between alloying elements that do not markedly affect the solubility of hydrogen, elements that increase the solubility, and elements that reduce it. They named gold, tin, and aluminum as examples of this last group and reported hydrogen solubility data at 1225°C. for the copper-rich side of these alloy systems at atmospheric pressure. Without giving experimental results, they stated that the amount of hydrogen dissolved by liquid copper alloys is proportional to the square root of the pressure as in pure metals. These authors suggested that in a limited way the effect of an alloying element on the solubility of a gas is related to the constitution diagram for the alloy system. Sieverts7 also called attention to the fact that the curve of hydrogen solubility versus composition of copper-tin alloys shows a sharp change of direction at the composition of Cu3Sn and suggested that this compound persists at least to some extent in the molten state. Iwas3é reported large hydrogen solubility values for several compositions of copper- tin alloys, which appear to be in error.

Jan 1, 1944

By R. A. Matuszak

This paper discusses the major portion of the hoist (drag or crowd) system and it shows how static control accomplishes its major aims. In 1959, the first truly static control for Ward-Leonard equipped electric excavators was designed, developed and placed in service. The control system, originally intended only as a more modern electronic type of alternate to the proven rotating amplifier control system has since proven to be much more. When they conceived the original system, the designers had much more in mind than simply replacing the rotating amplifier with one that had no moving parts. The long range plan, which started with the initial system consisting of an SCR (silicon controlled rectifier) preamplifier and magnetic amplifier power amplifier, called for eventually, a control system low in cost and maintenance, relatively simple in design and extremely reliable. The plan also included the elimination of as many of the shortcomings of the rotating system as possible. No small accomplishment, when it is considered that the rotating control system had been, with only minor modifications, the standard of the industry for 20 years. The final step in the original design plan called for the eventual development of an amplifier that could be used as one of the basic building blocks of the future. DEVELOPMENT RESULTS Since the successful unveiling of the first static control system, continuous development has resulted in a slow, but sure progression along the path described by the original plan. The first version of the new control corrected one of the shortcomings of the rotating system by removing the necessity of operator anticipation. This was accomplished by making the system faster in response so that the operator noticed virtually no delay between his movement of the master controller and that of the machine. Thus, after the operator became familiar with the operating characteristics of the machine, he was able to become more relaxed while digging. The natural result of this accomplishment was higher production. All of the subsequent versions of this new control were even faster than the initial design. Although it was not distinguishable by the operator, the further increase in response resulted in large gains in the limiting of transient torque peaks applied to the machine while digging. Also, a more effective control of the torque and power peaks was obtained when plugging the motion being controlled to a stop. (Plugging is the use of the Ward-Leonard ability to regenerate power and absorb energy from the load to

Jan 1, 1964

By M. I. Jacobson, M. L. Hammond

The solid solubilities of high-purity silver, aluminum, chromium, copper, and iron in zone-refined beryllium have been determined. Diffusion couple sandwiches of beryllium with aluminum, copper, and silver foil and diffusion couples of beryllium with two-phase alloys in the Be-Cr. Be-Fe, and Be-Ag systems were analyzed by electron beam micro-probe techniques. This paper describes the material used, the experimental methods for preparing the diffusion couples and the alloys, the analytical techniques, and the results obtained. The results are compared with those of previous investigators who used materials of lower purity. ~NVESTIGATORS of beryllium phase diagrams have often been hampered in their interpretations of certain phase boundaries because of the relatively low purity of the beryllium used. This has sometimes resulted in the appearance of three phases in the regions where only two should exist. Advances in purification methods, specifically zone refining, have made available beryllium that is considerably purer than the material previously used for phase diagram studies. The primary object of this investigation was to reex-amine portions of the beryllium-rich end of the binary systems of beryllium with silver, aluminum, chromium, copper, and iron to determine more accurately the limits of terminal solid solubility. The five elements—silver, aluminum, chromium, copper, and iron—include some which are commonly found as the major impurities in beryllium, some of which are being used as solid-solution alloying elements, and some of which are used in ductile matrix alloys. They are thus of considerable importance to physical metallurgists who must work with beryllium but who must rely on the present inaccurate or incomplete diagrams. The determination of more reliable diagrams would aid researchers concerned with the problems of alloying, heat treatment, and ductility. MATERIAL The beryllium was acquired from the Franklin Institute in the form of a single-crystal, 6 in. long by 1 in. in diam, zone-refined in three passes from Pechiney SR-grade beryllium bar. The principal impurities, as determined by mass spectrography at Battelle Memorial Institute, are shown in Table I. Vacuum-melted copper, silver, and aluminum, and electron-beam zone-refined iron were obtained from the Materials Research Corp. in the form of 1/2-in.- diam bars. Iodide chromium was obtained as flakes from the Chromalloy Corp. Analyses supplied with these metals are shown in Table 11. EXPERIMENTAL PROCEDURE Preparation of Diffusion Couples. Two types of dif-fusion couples were used in this study. For the copper, silver, and aluminum systems, the couples were sand-

Jan 1, 1969

By William Klement

THIS note reports the results of some attempts to metastably extend the primary solid solubilities of tin, antimony, and silicon in silver by rapidly quenching these binary alloys from the melt. The procedures employed for alloy preparation, quenching, and Debye-Scherrer X-ray diffraction measurements have been described elsewhere. The lattice parameters obtained for the fcc structures in Ag-Sn and Ag-Sb alloys are presented in Fig. 1, together with the results of Owen and Roberts.4 Alloy compositions are believed to be within ± 0.2 at. pct on the basis of negligible weight losses during preparation and reproducibility of the lattice spacings. Diffraction lines from hcp phases were also detected: the relative visual intensities of the fcc (200) and hcp (10.2) lines were estimated as shown in Table I. The intensities were m for the (200) and w for the (10.2) in a quenched 13.6 at. pct Sn alloy: a lattice spacing for the fcc structure could not be reliably obtained, however. As seen from Fig. 1, the lattice parameters vary linearly with composition up to 8., at. pct Sb and 13." at. pct Sn, respectively, which may be compared with the maximum equilibrium solid solubilities5 of 7.2 at. pct Sb and 11.5 at. pct Sn, respectively. The presence of the hcp phases, which were found together with the fcc phases, is a consequence of the competition1,3 in the nucleation and growth processes during solidification. Both the fcc and hcp phases must be of the same composition for those alloys in the range where lattice parameters increase linearly with solute concentration. Despite much effort with quenched alloys of several silicon concentrations, it has not been possible to obtain lattice spacings of sufficient precision to establish the variation of lattice parameter with composition or the maximum metastable solid solubility: the equilibrium data5 suggest little primary solid solubility of silicon in silver. For alloys containing less than 16 at. pct Si, the Si (111) diffraction line was not observed. For alloys containing 10 to 25 at. pct Si, faint low-angle lines were detected and these could be indexed as the (10.0), (00.2). and (10.1) reflections of an hcp structure with a = 2.87 + 3A. c = 4.52 ± 3A, and c/a = 1.57 ± 2. The 16 at. pct Si alloy was quenched to, and examined at. liquid nitrogen temperatures without any change observed in the proportion of the hcp phase. These experiments were jointly supported by the Atomic Energy Commission and Office of Naval Research under a program directed by Professor P. Duwez. The assistance of H.-L. Luo and A. Abu-Shumays is acknowledged. as is the support afforded

Jan 1, 1965

The Bougainville ore body was discovered in 1964 by a partnership of Conzinc Rio Tinto of Australia and New Broken Hill Consolidated Limited. The ore body is a porphyry copper in a fine-grained quartz diorite, which intrudes andesite volcanics and is located at an elevation of about 2, 000 ft in the Crown Prince Range of Bougainville in the Solomon Islands. Mineralization is predominantly chalcopyrite with some bornite and some gold and silver present. Rainfall in the area amounts to 200 in. (5. 08 m) per year. An active volcano is situated only 24 miles (38.4 km) from the mine, and all structures were designed to resist seismic shocks. An interesting and unique feature of the Bougainville operation was that the overburden was stripped with hydraulic monitors. Bougainville Copper, at 90,000 tpd, is the largest copper concentrator to be designed and constructed at one time; and besides the twin 54 in. by 74 in. Allis-Chalmers gyratories, it features seven 7 ft (2. 13 m) standard and fourteen 7 ft shorthead crushers, in addition to nine 18 ft diameter by 21 ft long (5. 5 m by 6. 4 m), 4250 hp, single -stage ball mills. During the design stage of the Bougainville primary crushing plant, several alternates were studied because the ore was expected to break with the production of large amounts of small-sized particles but with a minimum of fines. These alternates included two 54 in. by 74 in. gyratories with grizzlies, two 60 in. by 89 in. gyratories, and one 72 in. by 96 in. gyratory, the latter two installations without grizzlies. The two 54 in. units with grizzlies were finally selected as giving good reliability and the ability to handle the large amounts of small material in the feed. As originally installed, grizzly bars were set at 8 in. (203 mm); but, in an effort to perform more interparticle crushing in the primary and less rock-on-steel crushing in the secondaries and tertiaries, a test is underway (1976) to determine the effect of using 6 in. (152 mm) grizzly spacings (see write -up on Anaconda's crusher at Butte). The Bougainville ore is mined with 17 cu yd (13 cu m) shovels and hauled in 105, 170, and 210 st trucks to the crushers, which are equipped for two-side dumping. Up to 40% of the ore passes the grizzlies, which are equipped with splitters; and additional horizontal splitter bars are located directly above the spider caps. Because of the grizzlies, the crushers are supported by unique U-shaped enclosures, which are in turn supported by the end and center walls of the installation.

Jan 1, 1978

By K. Huessener

In presenting the following data on combustion in the open hearth furnace and the advisability of automatic combusion control, the author finds himself much more severely handicapped by the lack of reliable test results than he had anticipated when he first undertook to write this paper. In order thoroughly to investigate how the results of an open-hearth furnace are influenced by combustion, one would have to draw up a large number of heat-balance sheets, as Kinney and McDermottl have given for one heat in their extremely able paper on "Open Hearth Efficiency,' presented before the American Iron and Steel Institute on October 27th,1 1922. Instead of covering only one heat, however, such heat-balance sheets would have to embrace a large number of heats, and not only for one kind of fuel, but for all the various fuels in customary use. Use of Radiation-protected Pyrometer Such tests necessitate extremely careful temperature readings, and here the first serious difficulty presents itself. Nearly all the temperature readings so far published have been taken with thermocouples for the lower ranges and with optical or radiation pyrometers for the higher ranges. This method of measuring reveals the temperature of the surrounding walls, or in the case of optical or radiation measurements, the temperature of that part of the opposing walls which has been focused by the instrument. The error in ascertaining the temperature of the gases entering or the waste gases leaving the checker chambers is probably not very large, as the flowing gases impart their temperature to the walls of the flues. On the other hand, the uptakes, where the preheat temperature of gas and air are usually measured, are under the influence of radiated heat from the port ends, and correct temperature readings can here be taken only by using a radiation-protected pyrometer of the aspirating type.

Jan 1, 1926

By E. F. Kingsbury

One of the well-known and important uses of the noble or precious metals has been for electrical contacts. In fact, the elements of this group, comprising gold, silver and the six platinum metals, have been called "noble" because of their ability to resist heat and corrosion, properties which were early found to be of importance in good contacts. Of these, platinum and its iridium alloys, palladium, and silver, have been extensively used. In recent years the electrical industry has been responsible for about one-eighth of the total consiimption of the platinum metals in the United States. Information is not available as to what part of this one-eighth has been used for contacts but it is certainly an important one. Substitutes for Platinum During the past 20 years a considerable number of contact alloys have been proposed in the patent literature largely with the aim of more or less replacing platinum by gold or silver, and some of these alloys are finding increasingly widespread application as the reliability of their performance becomes established. From even the partial data at hand it appears that this substitution by the less precious metals has replaced at least one-half of the amount of platinum that the entire electrical industry would otherwise be consuming at the present time. While the subject is of considerable interest to the metallurgist it is even more so to the electrical engineer and it is surprising that the literature records no systematic and comprehensive investigation along these lines. Practically all the scattered work on noble metal contacts has centered around platinum as a standard and has had two more or less distinct aims. One of these has been the replacement of platinum by cheaper matcrials, and the other, the dcveloprnent of materials of superior electrical performance. The merit of a contact metal has been assumed to be dependent on its infusibility, and since thc more precious metals have the higher melting points there has naturally been an association of the two qualities in the sense that the more precious were

By I. N. Knapp

I Herewith present some notes on the use of Portland cement to cement in the casing, and for plugging, to exclude water from oil and gas wells, and the methods employed. I have used my best efforts to. make each step of the operation of cementing wells perfectly clear. The information is the result of actual experience and observation. The illustrations are from original drawings made especially for this paper. Portland Cement It is not necessary to discuss here the manufacture of cement. Any established brand of the slower setting Portland cements may be purchased with the confidence that it will harden, if properly used, and exclude water from and plug wells efficiently. Setting.—By the setting of cement is meant its initial change from a soft or plastic mortar to a friable solid. After the cement has become thoroughly set it is still very weak and can be readily pulverized in the fingers. Setting is thought to be effected by the crystallizing out of the silicate and the aluminate of lime, which are soluble in water in their anhydrous form. After dissolving in the water they pass to the hydrated state, in which they are insoluble, and hence are precipitated in a crystalline form. Ordinarily neat Portland cement mortar remains perfectly plastic for from 1 to 1 1/2 hr. after mixing with water at about 70" F. A higher temperature accelerates and a lower retards setting.. Hardening.—This is due to a continual crystallization of salts from solution, and to further chemical and physical changes which develop slowly, but which continue for long periods of time. Testing.—It is no more necessary for an operator to go into the scientific testing of cement to be used in a well than to so test the pipe used. He must depend for the quality of each on the tests and reliability of the manufacturer. Cement or pipe may be damaged in shipment so

Jan 1, 1915