Search Documents

By R. M. Leibrock, R. P. Vincent, C. W. Ziemer

The Stanolind flowmeter, which employs a hot-wire anemometer connected in a Wheat-stone bridge circuit, has proved useful for determining the relative productive ability of individual sand members of gas wells. The operation of this instrument in measuring gas velocities in the well bore above each producing member has provided both a direct and accurate means of analyzing reservoir performance. Results of tests conducted with the well flowmeter in the Hugoton gas field of western Kansas have indicated some rather unusual production characteristics. In two cases it was found that all or the greater part of the total gas produced was coming from one section in wells where four "pay" sections had been perforated individually. These actual measurements contradict in many instances the indications of data obtained from electric logs and from core analysis; the fact that these latter sources often give incorrect results, demonstrates the necessity of a method, such as is provided by the well flowmeter, for accurately determining the amount of gas coming from each producing member. Introduction In any gas well where a number of pay sections have been perforated individually and are producing to a common outlet, the question arises as to the relative amounts of gas being passed through each set of perforations. In the past it has been the policy to depend on core analysis to estimate relative productivities, or, where the sections were not cored, to obtain some idea of production characteristics from electric-log studies. The weaknesses in these methods are readily apparent and indicate the need for more reliable means of measuring gas flow from each zone. The Stano-lind flowmeter* was developed for this purpose. Preliminary tests were made with the instrument in the Katy gas field near Houston; however, the bulk of the routine work with the well flowmeter has been confined to the Hugoton gas field in western Kansas, where results obtained have been encouraging. A description of the instrument, the field technique employed in testing, and a few of the results obtained in the Hugoton area are discussed in this paper. Description or Instrument The well flowmeter is 1¾ in. od and 7 ft long; it is entirely self-contained, can be run through tubing as small as 2 in. id in wells with high pressure (4500 psi) and temperature (210°F) and is lowered on a wire line commonly used for other instruments of the bottom-hole type at falling rates up to 500 ft per minute. It will detect gas flow as low as 10 ft per minute linear velocity, and yet withstand and record velocities of 1000 ft per minute without damage to the detecting element. Killing the well is not required nor desirable for running a production profile when using the instrument, and it is necessary to stop flow for only a short time. The detecting element of the instrument is a hot-wire anemometer connected in a

Jan 1, 1948

By C. Ernest Birchenall, Robert F. Mehl

Application of diffusion laws in the customary form to experimental studies in binary metallic solid solutions has shown the diffusion cocfficient to vary with concentration for all systems investigated. The factors determining this variation have not been ascertained. However, the question of whether the diffusion coefficient would become a constant, independent of concentration throughout a single phase if the concentration gradient in the diffusion equation were replaced by an activity gradient has been an attractive subject for speculation. Wagner¹ derived an expression for the force acting on a diffusing particle in terms of the chemical potential. This was also the approach chosen by Jost2 in his monograph. From a somewhat different point of view, Eyring3 and his co-workers have used activity gradients when dealing with diffusion in concentrated nonideal solutions. The only actual test with experimental data is that given by Darken,4 though this is more qualitative than quantitative. Many others opposed the application in any way of thermodynamic concepts to kinetic phenomena, including diffusion processes. A rigorous examination of this principle requires good data expressing the relationship between activity and concentration for solid solutions for which reliable diffusion work has been done. The literature provides such information only for the interstitial solution of carbon in gamma iron (austenite) and for the substitutional copper-zinc solutions (alpha brass). Activity data for carbon in austenite at 800°C and 1000°C are available from the recent work of Smith5 on the equilibrium of hydrogen-methane and carbon monoxide-carbon dioxide mixtures with gamma iron. Combining these with the diffusion studies of Wells and Mehl6 makes possible a quantitative test for this interstitial solid solution. The vapor-pressure determinations for zinc over brass by Hargreaves7 allowed the calculation of activities in this system over a wide range of temperatures and concentrations. Extensive investigation of diffusion in this substitutional solid solution has been carried out by Rhines and Mehl.8 Activities in Brass9 If the vapor phase of zinc is assumed to behave as an ideal gas, any solid or liquid solutions that are in equilibrium with the same partial pressure of zinc at the same temperature have the same thermodynamic activity of zinc. In order to assign a numerical value to the activity azn, it is necessary to choose some standard reference state to which an activity value of unity is arbitrarily assigned. It is customary to choose the liquid or solid state of the pure material. Then azn is defined numerically by

Jan 1, 1947

By C. Ernest Birchenall, Robert F. Mehl

Application of diffusion laws in the customary form to experimental studies in binary metallic solid solutions has shown the diffusion cocfficient to vary with concentration for all systems investigated. The factors determining this variation have not been ascertained. However, the question of whether the diffusion coefficient would become a constant, independent of concentration throughout a single phase if the concentration gradient in the diffusion equation were replaced by an activity gradient has been an attractive subject for speculation. Wagner¹ derived an expression for the force acting on a diffusing particle in terms of the chemical potential. This was also the approach chosen by Jost2 in his monograph. From a somewhat different point of view, Eyring3 and his co-workers have used activity gradients when dealing with diffusion in concentrated nonideal solutions. The only actual test with experimental data is that given by Darken,4 though this is more qualitative than quantitative. Many others opposed the application in any way of thermodynamic concepts to kinetic phenomena, including diffusion processes. A rigorous examination of this principle requires good data expressing the relationship between activity and concentration for solid solutions for which reliable diffusion work has been done. The literature provides such information only for the interstitial solution of carbon in gamma iron (austenite) and for the substitutional copper-zinc solutions (alpha brass). Activity data for carbon in austenite at 800°C and 1000°C are available from the recent work of Smith5 on the equilibrium of hydrogen-methane and carbon monoxide-carbon dioxide mixtures with gamma iron. Combining these with the diffusion studies of Wells and Mehl6 makes possible a quantitative test for this interstitial solid solution. The vapor-pressure determinations for zinc over brass by Hargreaves7 allowed the calculation of activities in this system over a wide range of temperatures and concentrations. Extensive investigation of diffusion in this substitutional solid solution has been carried out by Rhines and Mehl.8 Activities in Brass9 If the vapor phase of zinc is assumed to behave as an ideal gas, any solid or liquid solutions that are in equilibrium with the same partial pressure of zinc at the same temperature have the same thermodynamic activity of zinc. In order to assign a numerical value to the activity azn, it is necessary to choose some standard reference state to which an activity value of unity is arbitrarily assigned. It is customary to choose the liquid or solid state of the pure material. Then azn is defined numerically by

Jan 1, 1947

By A. B. Kinzel, Walter Crafts

Inclusions of nonmetallic matter have long been recognized as objectionable in steel. A complete theory of the effect of inclusions, which is consistent with that held today, was outlined in Howe's early work on the metallurgy of iron and steel. This, by analogy with wrought iron, assumes that the observed difference in properties between specimens with and across the direction of rolling is due to slag enclosures. The fact that wrought iron shatters in ballistic test is taken as an indication of the effect of inclusions on the resistance to'shock. Since that time, the development of the metallurgical microscope has shown the discrete nonmetallic inclusions in the iron matrix. Better resolution has brought out the great number of inclusions, and the availability of good microscopes in steel mills and laboratories has constantly drawn more attention to these inclusions. This recent emphasis on inclusions has resulted in studies as to their nature, mode of formation and methods of elimination, such as the work of Wohrman, Dickenson, Herty and Schenk. In addition to the published works, many investigations which have not been published have been carried out by private laboratories and have resulted in the application of specifications intended to limit inclusions in many qualities of steel. Neverthless, a clear understanding of the quantitative effect of inclusions on the physical properties of steel has been lacking. It is the specific purpose of this study to determine the quantitative effect of inclusions on the physical properties of steel that determine its behavior under dynamic stress. The study has shown that a quantitative relation between counted inclusions and impact strength does exist in normalized steels, but that factors other than readily visible inclusions are equally important. Furthermore, the present commercial rating of inclusions is unreliable with respect to counted inclusions or dynamic tests, and this study indicates that the tensile-impact test is more reliable as a measure of quality. General Scheme The general plan of the study follows: (1) To develop or establish a satisfactory measure of dynamic strength; (2) to develop or establish a

Jan 1, 1931

By J. R. Johanson

With the continuing development of automatic operations, it is important that reliable discharge rates through hoppers and bins be obtained for bulk solids. In most applications a feeder is used to control the feed rate. The selection of this feeder size is usually based on the rated ability of the feeder to move material without regard to the capability of the material to flow through the opening in the hopper onto the feeder. The dis charge rate through a given hopper opening may vary from zero to a theoretical maximum depending on the flow properties of the material. This paper presents an equation for the maximum discharge rate for a bulk material as a function of the hopper shape, the opening size and the flow properties of the material. Discharge-rate tests on various materials indicate good agreement with calculated values for opening sizes from a fraction of an inch to several feet. As part of a program to develop improved design criteria for bulk storage and handling facilities, a specific study of the methods involved in calculating the rate of discharge of bulk solids from hoppers and bins has been made. This study is closely related to earlier work done on the prevention of flow problems through the choice of proper design geometry of hoppers and bins1. The present paper is an extension of this earlier work, and therefore many of the concepts previously derived and explained will be used without explanation. Two types of flow will be considered: plane-strain flow in a wedge-shaped hopper and axial-symmetry flow in a conical hopper. The literature contains many studies on discharge rate for regular-shaped dry particles2*3 such as glass beads, lead shot and coarse dry sand. However, the work is empirical in nature, and it is difficult to extrapolate the given information to apply to moist, sticky materials typical of many industries. Some studies4 have shown a decrease in discharge rate with an increased moisture content of the material. However, no attempt was made to correlate the discharge rate with moisture. The method of calculating discharge rate presented in this paper was derived analytically from the basic knowledge of the flow of frictional, cohesive, granular solids, The equation includes the effect of material cohesion (stickiness), hopper configuration, opening size and bulk density of the material. THEORETICAL WORK The basic assumptions made in deriving the discharge rate equation are as follows: 1) The material is a frictional, cohesive, granular solid. 2) The flow is considered continuous and without significant density change. 3) The material at the hopper opening forms a continuously failing arch that is in dynamic equilibrium. 4) The strength of the material in the arch, which must be overcome for the arch to fail, is caused by the pressure in the flowing mass near the hopper opening. 5) This pressure at the hopper opening can be calculated5. If we consider the dynamic equilibrium of an arch of uniform thickness such as that shown in Fig. 1,

Jan 1, 1965

By J. K. Kerver, J. S. Osoba, J. G. Richardson, J. A. Hafford

A detailed study of a number of methods of relative permea-abilitv measurement has been made in a search for the tech-niqrle most suited to routine analysis of cores taken from reservoir rock. It has been found from tests run on the same samples of core material by a number of techniques that the Penn State, Hassler, Hafford, and dispersed feed techniques all yield results which are felt to be reliable. Conditions under which the faster single core dynamic technique may be used are described. Further work on the calculation of relative permeabilities to oil from data obtained by the gas drive method is needed before this latter rapid method can be utilized. Correlations between theoretical studies and experimental results have been obtained in studies of the boundary effect. pressure distribution in two-phase flow, and gas expansion effects. Previous conclusions that the effects of the outflow boundary could be made negligibly small have been substantiated. Results of experimentally determined oil and gas pressure distributions along a core sample during flow are presented. Further studies of the effects of rate of flow in the measurement of relative permeability-saturation relations have shown that results are independent of the rate of flow as long as the flow rate is below the point where inertial effects commence. An analysis of the effects of a severalfold expansion of gas along the flow path indicates that while saturation gradients are induced in the test sample, the errors caused by this phenomenon in relative permeability measurements are small. INTRODUCTION Many pages of literature have been devoted to pointing out the need for relative permeability-saturation relations in reservoir engineering. One of the most attractive ways of obtaining this information is by the analysis of samples of core material taken from the formation in question, and again literature has described man); methods for obtaining these data. It is the purpose of this paper to present the work that has been done in the study of some of these published methods together with some other methods that have been recently developed in this laboratory. Also, a study of some of the factors that influence the laburatory determination of relative permeability-saturation relations is presented. FACTORS WHICH AFFECT LABORATORY STUDY OF FLUID FLOW THROUGH RESERVOIR ROCK To determine relative permeability-saturation relations of samples of reservoir rock in the laboratory, it is important to know what factors affect these measurements in order that the magnitude of these effects can be ascertained and steps then can be taken to eliminate or, in some cases, to minimize them. The factors that have been investigated are the boundary effect, the effect of gas expansion. and the rate effect. Boundary Effect In laboratory experiments in which two immiscible fluids are flowed through a porous medium, there exists a discontinuity of capillary properties at the outflow face. This discontinuity exists became the fluids pass from a region of finite capillary pressure in the sample to a region of zero capillary pressure in an open receiving vessel. The capillary forces existing in the core caupe the rock to tend to retain

Jan 1, 1952

By J. E. Hilliard

Isobaric sections of the eutectoid region of the iron-carbon phase diagram have been exgerimentally determined at 35, 50, and 65 kb. The phase boundaries were located by metallographic analysis of specimens quenched after equilibriatwn at known temperatures and pressures. With increasing pres -sure a pronounced decrease in the solubility of FesC in austenite was observed together with a depression of the eutectoid temperature. These two effects resulted in a shift of the eutectoid composition toward a lower carbon content; at 65 kb the eutectoid was at less than 0.2 wt pct C. These results are in qualitative agreement with thermodynamic calculations. It has also been shown by calculations that Fe3C in contact with saturated austenite will be stable with respect to both graphite and diamond formation at all pressures above -3.5 kb. 1 HE investigation described in this article was part of a more general study of the effect of high pressure on transformations in Fe-C alloys. Thermodynamic calculations and exploratory runs made in 1959 at the start of the program indicated an appreciable change with pressure in the phase equilibria of Fe-C alloys. However, the calculations were not considered reliable enought to provide the quantitative information required for the interpretation of the effect of pressure on the kinetics of transformations. An experimental investigation was therefore made to determine a series of isobaric sections of the eutectoid region of the phase diagram at pressures up to 65 kb. EXPERIMENTAL PROCEDURE Materials. Seven alloys with analyzed carbon contents of 0.10, 0.20, 0.38, 0.60, 0.77, 0.93, and 1.20 wt pct C were prepared from Ferrovac" iron and high-purity graphite induction melted in magnesia crucibles under argon. The ingots were hot worked and swaged down to 0.19-in.-diam rod which was then centerless ground to a final diameter of 0.125 in. Samples for chemical and spectrographic analyses were taken from each end of the rods. The prin- cipal impurities were found to be Ni, Al, Co, and Si which were present in amounts up to 0.03, 0.02, 0.01, and 0.01 wt pct, respectively. Specimens were prepared by slicing the ground rods into pills 0.06-in. thick which were silver plated to reduce decarburization during the equilibration. Silver was chosen for this purpose because of its very low solubility for carbon and its mutual immisicibility with iron. High-Pressure Apparatus. The high-pressure runs were carried out in the "Belt" apparatus.' As shown in Fig. 1, this consisted of a cylindrical cell compressed between two Carboloy punches loaded by a uniaxle press. Radial support to the cell was given by the "belt" which was a Carboloy die heavily prestressed by a series of steel binding rings. Laminated gaskets of lava and metal separated the punches from the inner surface of the "belt". A cross-section of the high-pressure cell is shown in Fig. 2. Two specimen pills were located inside a resistance heater of 0.20-in.-diam Nichrome tubing. The ends of the tube were sealed with alumina and lava pills tamped in place after the

Jan 1, 1963

By R. H. Winn

In this paper a heterogeneous carbonate reservoir is considered as a succession of layers of formations of radically different porosities, permeabilities, water saturations, and rock matrix types; i.e., the heterogeneity is vertical rather than radial to the wellbore. Presumably each layer is more or less homogeneous. To determine the "net oil in place" in this reservoir it is desirable to know the porosity and water saturation of each layer. In addition, the section must be subdivided into that which will produce oil, that which will produce water, and that which will produce little or nothing. In numerous wells drilled in these reservoirs radioactivity surveys, guard electrode surveys, and caliper surveys have been made. These logs have been compared with core analysis data, when available, and the analysis of the surveys compared with production data. This study, still in progress, is intended to provide improved analytical techniques if such are possible. This paper is a progress report on the work. DETERMINATION OF POROSITY The neutron-gamma log has long been recognized as a measure of hydrogen concentration.1,2,3 In reservoirs that are free of clay, shale, or other hydrogen containing matrices, it has been accepted as a measure of porosity.4,5 Empirical methods to relate relative neu-tron-gamma intensity to porosity are often employed." To provide a more precise determination of porosity from the neutron-gamma log each instrument is calibrated immediately prior to each survey by a method which refers all tools to a hydrogenous cylinder. To insure stability a calibration check is made after each survey. These calibration records are printed as an integral part of the log that is recorded in standard counts per second. A detailed description of the calibration procedure is available in the literature.' The procedure employed insures that each Survey is numerically reproducible within the limits of statistical variation. To relate the standard neutron counts per second to porosity and hole size, records were made in test wells constructed of blocks of limestone. The porosities of the blocks were accurately measured and the blocks completely saturated with fresh water. Fig. 1 presents some of the results obtained in these test wells.' The lines shown in Fig. 1 were obtained by deriving an empirical equation relating the 11 points shown so that the relationship may be projected to larger and smaller hole sizes. A detailed description of the tool is available in the literature.' Field tests indicate that the tool is adjacent to the wall of the hole most of the time when the surveys are made in uncased holes drilled with saline muds. In this circumstance porosity may be calculated from Fig. 1 if the hole size is known. When fresh muds that form thick mud cakes are employed, the centralizing effect of the mud cake must be considered and the porosity determination is less reliable. In cased holes the combined effect of variations in hole diameter and the unknown eccentricity of the casing in the hole may make porosity determinations extremely unreliable. In any event, an accurate knowledge of hole size is essen-

Jan 1, 1958

By C. F. Rust

Experimental evidence is presented showing that reproducible formation resistivity factor measurements and resistivity index determinations on reservoir core samples map be made utilizing either the two- or four-electrode methods. Equipment is described which permits the application of either technique to the core specimen without loss of time and with a minimum amount of effort. Since electrical resistivity measurements on reservoir rocks are important not only in electric log interpretations, but also in the study of fundamental rock parameters, it was considered desirable to compare the applicability of both techniques of resistivity measurement. INTRODUCTION The techniques employed in the measurement of electrical resistivity on reservoir rocks, as practiced in the petroleum industry, may be reduced to two fundamental methods: one utilizing two electrodes only, usually referred to as the two-electrode method; the other using two additional electrodes and commonly known as the four-electrode method. In the former, the core sample whose resistivity is to be measured is mounted between two electrodes, usually metal discs, which serve to pass a current of known magnitude through the saniple. The potential drop across the sample, measured between these same two electrodes, and the core dimensions furnish the necessary data to compute he resistivity of the sample. In the four-electrode technique the end plates, again usually ol metal, still serve as current electrodes. Additional probes or electrodes dispersed along the sample are utilized to measure the potential drop. Both methods are used in practice1,2 and it is the purpose of this paper to compare the two techniques as applied to the determination of formation reiistivity factors and the resistivity index exponent n, in Archie's empirical equation I = p/po = Sw 11. To evaluate the two techniques it is desirable to point out the experimental precautions which must be taken to insure reliable results. It is evident from the electrode arrangements of the two- and the four-electrode methods that, for a given sample, the volume of sample included by the four-electrode method is less than the volume included by the two-electrode method. One of the prime difficulties associated with the two-electrode method is the possible occurrence of an abnormally high resistance between the electrodes and the brine-saturated sample, which results in erroneous resistivity values for the core sample itself. Attempts to alleviate this difficulty meet varying degrees of success. Methods used in the past employ such absorbent materials as brine-saturated Kleenex: chamois, or felt. A technique described by Morgan, Wyllie, and Fulton,1 appears to be more satisfactory. Their method consists of spraying or painting the end areas of a core sample with conductive silver paint. This technique reduces contact resistances between the porous medium and the electrodes to a value which is generally negligible as compared to the resistance of the sample itself. In the four-electrode method these requirements are not as stringent since separate probes are used to measure the potential difference acrozs a portion of the sample. In this case, contact resistance occurring at the current electrode; are of no consequence. and those appearing at the potential

Jan 1, 1952

By T. P. Papazoglou, N. A. D. Parlee, W. C. Phelps

HE high vapor pressures of metals such as lead, calcium, lithium, bismuth, and magnesium at steel-making temperatures present experimental problems which have thus far rendered it almost impossible to obtain really reliable data for their solubilities in liquid iron. Many investigators have attempted to equilibrate liquid iron in the same crucible with the undissolved liquid phase of such volatile metals. The published results,l-6 although useful, are often questionable on the grounds of not being obtained under true equilibrium conditions. Such information is not always of practical value in any case since the equilibrium vapor pressure is often several atmospheres and steel is not currently made at these pressures. Solubility measurements at lower partial pressures (< 1 atm) appeared to be more practical and easier to make. These data could be used to calculate solubilities at other pressures where Henry&apos;s Law is obeyed, and to estimate solubilities under other conditions of temperature and pressure with useful accuracy. This note outlines the development of a general technique for the measurement of solubilities in systems of this kind. The method involves equilibration of the high-boiling metal at known temperatures with the vapors of a low-boiling metal at known partial pressures. Analyses of quenched samples provide vapor pressure-solubility data and make calculations of alloy thermodynamics possible. The principle involved is similar to the closed-system diffusion-transport method which is difficult to apply with most high-melting liquid metals like iron, due to closure problems. A two-zone horizontal (molybdenum wire element) tube furnace, Fig. 1, provides two constant-temperature zones in a reaction tuve (3/4 in. ID by 1 in. OD by 36 in.). A high-boiling metal sample, 9, introduced in the higher-temperature zone, is maintained at temperature T1, and a volatile metal sample, 7, in the lower-temperature zone, is held at T2. A stream of argon with 10 pct hydrogen is passed via flowmeters, 1, and mixing-drying towers, 2 and 3. through the reaction tube at a favorable flowrate and acts as a carrier gas which entrains vapor from the volatile liquid metal at a specific constant partial pressure. The gas mixture passes through a system of constrictions, 6 and 8, to the higher-temperature zone, establishes intimate contact with the high-boiling liquid sample, 9, and exits through a small condenser tube. The entire system is at (nearly) atmospheric pressure and the volume of carrier gas passed is measured with a wet gas meter. When the high-boiling sample attains equilibrium with the vapor phase, both samples are removed and quenched. Analysis of the high-boiling sample for solute content reveals its solubility for the low-boiling metal at a vapor pressure calculated from carrier-gas volume and either a) weight loss of volatile metal or 6) weight gain of high-boiling sample plus condenser (which collects the undissolved vapors). To test the capabilities of the method, liquid silver at 1403&apos;C was equilibrated with lead vapor at various partial pressures. The relatively simple Pb-Ag system was particularly suitable for uncovering experimental problems and providing the first step toward investigations with more volatile metals and more difficult combinations.

Jan 1, 1965

By B. E. Eakin, A. L. Lee, M. H. Gonzalez

Expeximental viscosity and density data of lour natural gases are presented for temperatures from WO to 340F and pressures from 100 to 8.000 psia. A correlation is also discussed and results reported. INTRODUCTION This investigation is one of several efforts by the authors to provide viscosity data for pure hydrocarbons and mixtures. Results of some pure hydrocarbons and their mix tures have been presented." Several predictive methods and correlations have also been reported.&apos;," This paper presents the experimental viscosity and density data of four natural gases and confirms a correlation in a previous study. APPARATUS The viscometer was described previously. 2,6 A bank of stainless steel pycnometers was included to determine density in conjunction with the viscosity measurements (Fig. I). DATA AND MATERIALS The natural gases were furnished by the Atlantic Richfield Co. (Samples 1 and 21, the Continental Oil Co. (Sample 3) and the Pan American Petroleum Corp. (Sample 4). Table 1 shows the composition of these gases obtained by mass spectrometer analysis. The pure component viscosity data used in the correlation have been published."".&apos;"&apos;, &apos;" Experimental and calculated viscosity data for the natural gases are presented in Tables 2 through 5. CORRELATION Starling and Ellington"&apos; have reported several semi-empirical expressions based to a certain extent on the theory of viscosity advanced by Born and Green.&apos; The final expression presented by Starling and Ellingto&apos;n is: i&apos;. (micropoise) -- /t,, exp rX(7&apos;) p ..... (I) Eq. 1 was modified by Lee et 01." to represent mixture and pure component data simultaneously. This equation has the form: F = K exp [XpY] :.........(2) where K=- (7.77 i 0.0063M)Ti 122.4 + 12.9M +T .................(3) &apos; &apos; &apos; X= 2.57 + ---1914.5+ 0.0095M .... (4) Y = 1.11 -r 0.04 X ........(5) Over the pressure and temperature range studied in this investigation, this equation represents the data on methane, ethane, propane, n-butane and four methane-n-butane mixtures with a standard deviation* of ? 1.89 per cent. Density data by Sage and Lacey" were used to fit the equations. Eq. 2 gives reliable values of the viscosity of light hydrocarbons without prior knowledge of experimental viscosity values, but accurate density data must be available. Eq. 2 was used to predict viscosity values for the natural gases studied in this paper. The particular set of parameters contained in Eqs. 3 through 5 gave values that reproduced experimental data within 25 per cent. Needless to say, in using Eq. 2 better density values will give better viscosity results. However, those engineers who do not have accurate density values at hand or the time, or such facilities as a library, computer, etc. readily available, may feel uneasy in using Eq. 2. Therefore, the authors sought the easiest but by no means best density prediction method, which was reported by Kaf 30 years ago. A set of density values, which were calculated based on Kay&apos;s method, and a generalized compressibility factor chart were used to fit Eq. 2. The results are:

Jan 1, 1967

By G. H. Lair, B. J. Langford, S. H. Rockwood

Volumetric reservoir analysis is dependent upon a firm relationship between porosity, connate water, and net pay. Capillary presswe data on core samples interrelate these three factors. It is shown that other reservoir problems may be resolved: (I) whether water production is indigenous or extraneous to the oil producing interval, (2) an oil-water contact is being approached, and (3) whether the oil-water contact is remotely situated. INTRODUCTION Volumetric analysis of carbonate reservoirs challenges the ingenuity of the reservoir engineer due to an absence of data on the minimum oil-bearing and oil-producing pores of a given reservoir rock. Many studies with this as the ultimate objective are available on the physical characteristics and fluid-flow behaviors of the carbonate reservoir. Some of these publications are: Hassler, Brunner and Deahl&apos;s1 study of the role of capillarity in oil production; Jan Law&apos;s&apos; and A. C. Bulnes3 statistical treatment of core analysis data; Chalkley&apos;s method4,5 or estimating specific surface areas and porosity; Walter Rose&apos;s9 report on porosity, reserves, and recovery; Archie&apos;s78 tex-tural classification of carbonate rocks; Stewart and Spurlock&apos;s9 large core analysis; Purcell&apos;sl0 mercury injection method in studying capillary pressure phenomena; Stewart, Craig, and Morse&apos;s" model multiple-phase flow test in investigating the relative permeability effect; and Fatt&apos;s12 illumi-nating network model of porous me-dia. The present study shows that the static reservoir parameters of porosity, connate water, and net productive thickness may be interrelated by utilizing a statistical arrangement of mercury capillary pressure data in addition to routine core analysis. This report summarizes the techniques that are followed to obtain these relations which are applicable to carbonate and sandstone reservoirs that do not contain clays. Capillary pressure statistical studies may be extended to include clay-bearing rocks by utilizing water capillary pressure data. POROSITY It is necessary that the laboratory determine the porosity value that includes the pores that are filled with hydrocarbons and water in the reservoir. This is the reservoir&apos;s total porosity. When true total porosity values are not available, correlations between porosity and capillary pressure characteristics lose their significance since they cannot be related through oil-base mud core data to the porosity and connate water values found in reservoirs. Methods used to obtain reliable porosity data will not be discussed; however, care should be exercised in selecting samples for measurement. In homogeneously porous formations, small core plugs sampled frequently will furnish adequate information. Where heterogeneity, particularly vugginess, is present, large-core porosity data may be required; in such reservoirs a suite of capillary pressure samples may be selected from small plugs. CAPILLARY PRESSURE Capillary pressure data provide a method for relating two carbonate reservoir parameters, porosity and connate water saturation, which in turn permit delineation of productive rock types necessary for selecting the third parameter, productive thickness. Specific applications of capillary pressure data to petroleum reservoirs were suggested by Archie8 and Pur-cell."&apos; Their work demonstrated that in preferentially water-wet rock, porc

Jan 1, 1958

By W. T. Lankford, Low J. R., Gensamer M.

The problem of sheet metal formability is one which has received a vast amount of attention during recent years. In spite of the great amount of study and experimental work which has been devoted to this problem, many of its fundamental aspects are still not well understood. No generally satisfactory test has been developed which is capable of providing a reasonably adequate evaluation of sheet metal formability, particularly in borderline cases. Anomalies persistently arise in which a lot of supposedly satisfactory material exhibits excessive breakage when formed. This lack of suitable technological tests greatly hinders the design of new parts and the substitution of new materials in parts of existing design, frequently necessitating considerable costly trial and error experimentation on an actual production basis. When, at the beginning of World War 11, it became apparent that mass production methods of forming would bc required in the aircraft industry if the large numbers of military aircraft needed were to be supplied, renewed attention was focussed on the problem of sheet metal formability. It was widely recognized that the formability requirements placed on sheet metals had been steadily increasing in severity through the years, especially as greater and greater emphasis was placed on streamlined designs with the resultant freer application of doubly curved surfaces. The recent advent of several new high strength aluminum alloys of more limited formability than some of the older alloys also served to emphasize the need for new approaches to the problem. It seemed evident that progress in the technology of sheet metal forming would depend to a great extent on the development of more reliable criteria for the evaluation of formability. Although the problem is admittedly very complex, the most logical approach appeared to be through studies of the fundamental material properties of sheet metals, especially under complex stress conditions simulating those prevailing in actual forming operations. Most previous investigations have failed to make full use of existing knowledge of fundamental material properties, and in many instances have attempted correlations with properties which are now recognized as being ambiguous in nature. This investigation was undertaken, therefore, with the aim of developing methods for the study of the flow and fracture of sheet meta1s under combined stresses, and of making use of such methods as might be developed in

Jan 1, 1947

By Low J. R., Gensamer M., W. T. Lankford

The problem of sheet metal formability is one which has received a vast amount of attention during recent years. In spite of the great amount of study and experimental work which has been devoted to this problem, many of its fundamental aspects are still not well understood. No generally satisfactory test has been developed which is capable of providing a reasonably adequate evaluation of sheet metal formability, particularly in borderline cases. Anomalies persistently arise in which a lot of supposedly satisfactory material exhibits excessive breakage when formed. This lack of suitable technological tests greatly hinders the design of new parts and the substitution of new materials in parts of existing design, frequently necessitating considerable costly trial and error experimentation on an actual production basis. When, at the beginning of World War 11, it became apparent that mass production methods of forming would bc required in the aircraft industry if the large numbers of military aircraft needed were to be supplied, renewed attention was focussed on the problem of sheet metal formability. It was widely recognized that the formability requirements placed on sheet metals had been steadily increasing in severity through the years, especially as greater and greater emphasis was placed on streamlined designs with the resultant freer application of doubly curved surfaces. The recent advent of several new high strength aluminum alloys of more limited formability than some of the older alloys also served to emphasize the need for new approaches to the problem. It seemed evident that progress in the technology of sheet metal forming would depend to a great extent on the development of more reliable criteria for the evaluation of formability. Although the problem is admittedly very complex, the most logical approach appeared to be through studies of the fundamental material properties of sheet metals, especially under complex stress conditions simulating those prevailing in actual forming operations. Most previous investigations have failed to make full use of existing knowledge of fundamental material properties, and in many instances have attempted correlations with properties which are now recognized as being ambiguous in nature. This investigation was undertaken, therefore, with the aim of developing methods for the study of the flow and fracture of sheet meta1s under combined stresses, and of making use of such methods as might be developed in

Jan 1, 1947

By H. G. Doll

&apos;This paper discusses a method and apparatus for determining the dip of formations traversed by a drill hole, by means of electrical measurements in the hole. The process consists in recording the Spontaneous Potentials present along three oriented generatrices in the hole. By comparison of the three curves thus obtained, after application of a correction factor to compensate for any deviations of the hole, the dip angle and the dip direction are determined. Excellent accuracy is obtained for dip angles over 10°. Because the method is simp1e and the apparatus rugged, the measurements are rapid and reliable; consequently, they can be made at all the levels that are of interest at any time after the well has been drilled. Mechanical cores are not needed to evaluate the dips. A convenient, time-saving procedure is to perform the dipmeter survey at the time the electrical log is taken, using for both operations the same cable and truck. Actual examples of results obtained in wells of the Gulf Coast area are given. Introduction The problem of determining the angle and direction of the dip of the strata traversed by a drill hole has practical interest, and sometimes vital importance, which need not be emphasized to the oil industry. The need for that type of information has existed ever since wells have been drilled. Certainly it has not subsided, in spite of the numerous inventions and improvements made in other fields of the art of drill-hole exploration. The few examples given in this paper are but illustrative of this fact. In the past, methods have been devised, and used, to solve this problem, but generally they have met with limited success, possibly because they failed more or less to answer the requirements of a modern age for fast yet accurate measurements. If accurate, the results were obtained at the cost of very tedious and lengthy operations. The new S. P.* dipmeter service offered to the oil industry is the result of exhaustive and in this particular field. In 1032 a dipmeter and electromagnetic teleclinom-eter service was made available. The apparatus employed then was of a rather delicate and costly construction, and the measurements had to be made with precautions sometimes difficult to secure on the rig. Although the information given by the electromagnetic dipmeter was limited to the direction of the dip, very interesting results were obtained in California, Trinidad, Venezuela, Rumania and, most notably, in the Netherlands East Indies.+ Apparatus The S. P. dipmeter surveys present none of the drawbacks mentioned above. The apparatus is rugged and free from constructional complications, therefore well adapted to field use. This, combined with the new, basically simple approach to the problem, explains the rapidity of execution of the measurements. The results are remarkably accurate and they are complete, giving the

Jan 1, 1946

By H. G. Doll

&apos;This paper discusses a method and apparatus for determining the dip of formations traversed by a drill hole, by means of electrical measurements in the hole. The process consists in recording the Spontaneous Potentials present along three oriented generatrices in the hole. By comparison of the three curves thus obtained, after application of a correction factor to compensate for any deviations of the hole, the dip angle and the dip direction are determined. Excellent accuracy is obtained for dip angles over 10°. Because the method is simp1e and the apparatus rugged, the measurements are rapid and reliable; consequently, they can be made at all the levels that are of interest at any time after the well has been drilled. Mechanical cores are not needed to evaluate the dips. A convenient, time-saving procedure is to perform the dipmeter survey at the time the electrical log is taken, using for both operations the same cable and truck. Actual examples of results obtained in wells of the Gulf Coast area are given. Introduction The problem of determining the angle and direction of the dip of the strata traversed by a drill hole has practical interest, and sometimes vital importance, which need not be emphasized to the oil industry. The need for that type of information has existed ever since wells have been drilled. Certainly it has not subsided, in spite of the numerous inventions and improvements made in other fields of the art of drill-hole exploration. The few examples given in this paper are but illustrative of this fact. In the past, methods have been devised, and used, to solve this problem, but generally they have met with limited success, possibly because they failed more or less to answer the requirements of a modern age for fast yet accurate measurements. If accurate, the results were obtained at the cost of very tedious and lengthy operations. The new S. P.* dipmeter service offered to the oil industry is the result of exhaustive and in this particular field. In 1032 a dipmeter and electromagnetic teleclinom-eter service was made available. The apparatus employed then was of a rather delicate and costly construction, and the measurements had to be made with precautions sometimes difficult to secure on the rig. Although the information given by the electromagnetic dipmeter was limited to the direction of the dip, very interesting results were obtained in California, Trinidad, Venezuela, Rumania and, most notably, in the Netherlands East Indies.+ Apparatus The S. P. dipmeter surveys present none of the drawbacks mentioned above. The apparatus is rugged and free from constructional complications, therefore well adapted to field use. This, combined with the new, basically simple approach to the problem, explains the rapidity of execution of the measurements. The results are remarkably accurate and they are complete, giving the

Jan 1, 1946

By F. E. Harris

IT has been said that carbon is "ubiquitous" with reference to iron alloys. Certainly at temperatures where carbon and iron form the solid solution, austenite, it may be readily added to, or removed from, steel surfaces. Differences in concentration potential are the sole requirements for carbon flow. To measure the rate of carbon flow, a proportionality factor, D, is arbitrarily expressed in units of (length)2 X (time)-1. If the term used for carbon concentration is weight pct C, as is customary, then a factor must be found, changing this term to one of weight per unit volume when the diffusion coefficient, D, is used in flow formulae. The determination of D values for carbon is complicated since D varies with the concentration itself. The Matano method has often been employed for systems involving a variant D. This method expreses an evaluation of unsteady flow whereby .0 is given a relationship with the numerical value of C-X slopes. The author contends that this solution is incorrect, except when D is invariant. The primary purpose of this paper is to support this contention. Here diffusion is controlled under two conditions of flow. The first part deals with the steady state; the second part considers unsteady flow under definite restrictions. Beginning with the fundamental concept, the development is continued until equations for C-X curves are obtained. The solution is then subjected to experimental data. It is realized that a great amount of reliable data is required for a rigorous proof. No such research is claimed. Instead an attempt is made to set forth the physical significance of the diffusion mechanism, and particularly to express the factors which influence the flow of carbon in austenite. Of equal significance is the implication that gaseous media may be employed with reasonable accuracy in making these determinations. THE STEADY STATE DIFFUSION OF CARBON IN AUSTENITE The fundamental experiment defining diffusion in solid metals may be readily performed for carbon in gamma iron.1 For this experiment a thin plate of medium carbon steel is chosen. The surfaces of this plate may be taken as two parallel planes which may be considered infinite for points well in the center of the planes. These two planes are held at different concentrations of carbon at a constant temperature. This temperature, 1700°F for example, is one where the single phase, carbon in solution with gamma iron, exists. When these conditions are held for a sufficient time the concentration of carbon of the different points of the solid settles down towards its steady state value. At points well removed from the ends, the concentration will remain the same along planes parallel to the surfaces of the plate.

Jan 1, 1947

By R. D. Pehke, J. F. Elliott

The solubility of nitrogen in liquid pure iron has been measured as a function of pressure and temperature. Sieverts&apos; Law is obeyed at all pressures up to 1 atm and the temperature coefficient of solubility is 8 x 106 %/°C. The solubility of nitrogen in liquid iron alloys has been studied by the Sieverts&apos; method and by the sampling method. The solubility is decreased by Al, C, Co Cu, Ni, 0. Si atzd Sn, and it is increased by Cr, Cb, Mn, Mo, Ta, W, and V. Interaction coefficients eN, for the effect of these elements on nitrogen dissolved in liquid iron, are reported. 1 HE effect of nitrogen upon the properties of steel may be desirable or not, depending upon the composition, processing treatment, and the use of the product. To understand the behavior of nitrogen in the various steelmaking processes, it is necessary to have reliable fundamental data pertaining to the solubilities, rates of solution, and chemical reactions of nitrogen in steel, particularly in the liquid state. In an effort to extend our knowledge in these areas, an investigation of the thermodynamics and kinetics of the solubility of nitrogen in liquid iron alloys was undertaken. The thermodynamic aspects of the study are presented in this paper. The solubility of nitrogen in liquid pure iron has received the attention of several investigators whose results are summarized in Table I. Reasonable agreement among the more recent researches1-l8 is found for the solubility of approximately 0.044 wt pct at 1600°C and 1-atm pressure of N,, for the temperature coefficient of solubility being small but positive, and for adherence to Sieverts&apos; law for pressures up to 1 atm. The solubility of nitrogen in a number of binary liquid iron alloys has been studied: Fe-A1,3 Fe-As,16 Fe-C,3, 71 18, 19, 20 Fe-Cr ,5,7, 10, 11, 15 21 Fe-Co,&apos;4, &apos;6 Fe-Cu,&apos;6 Fe-Mn,10, 11, 18 Fe-Mo,13, 16 Fe-Ni,10, 11, 13, 15, 16 Fe-O,16, 17, l9 Fe-p,7 Fe-S,l6 Fe-Sb,16 Fe-Se,lg Fe-Si,4) 97 &apos;77 187 19>2° Fe-Sn,16 and Fe-v.51 &apos;3 A few ternary systems have been studied, most of which were reviewed by ~angenberg" who applied the methods suggested by WagnerPz3 Chipman,24 Darken and G~rry, and Morris and Buehl26 for predicting solubilities in multicomponent alloys. Langenberg22 and Humbert and Elliott15 compared the solubilities computed from simple binary alloy systems with experimental measurements of nitrogen solubilities in liquid iron containing two or more alloying elements. The interaction coefficients for nitrogen in

Jan 1, 1961

By Cleland N. Conwell

APPLICATION of seismic methods to the location of buried channels in placer mining is fairly common knowledge, yet some of the facets of seismic refraction surveys have remained obscure in their application to mining. This description by a member of the U. S. Bureau of Reclamation team investigating bedrock at the Oso Dam site, may offer a lead to wider application of the method for bedrock determinations in engineering of mine and mill plants, tailing disposal, and water supply. It may also offer assistance in planning geological exploration in areas covered by overburden. Pertinent, and perhaps more than passingly significant, is that the seismic survey of the Oso dam site started at noon and was completed the afternoon of the next day. Location Oso dam site is on the Navajo River, Archuleta, County, Colo., 30 miles southeast of Pagosa Springs, Colo., 10 miles northwest of Chama, N. M. Bedrock at the proposed dam site is Mesa Verde Formation, Cretaceous age sandstone. The nearest good sandstone exposure is about 5/8 of a mile upstream from the location of the seismic determinations. The material above bedrock is sand and gravel with sandy loam soil covering benches above the river. The site appeared favorable, after a geologic and topographic reconnaissance, but overburden thickness was unknown. Exploratory drilling was not contemplated in the near future so a short seismic investigation was selected as the most suitable method of determining depth to bedrock. Field Procedure Geophysically, a seismic depth investigation is simply the measurement of depth from ground surface to the top of a layer which transmits seismic waves at a higher velocity. In this case the high-velocity seismic layer tentatively correlates with the Mesa Verde sandstone. Field procedure required a seismic explorationline or "spread" with 12 geophones set at measured intervals. Explosive charges were buried at few feet in the ground and detonated at shotpoints near the ends of the spread, and at intermediate points. The time of travel of the seismic waves from the shotpoints through the ground to each of the geophones along the spread was measured and recorded photographically with equipment housed in a field truck. The seismograph on each spread provided a time-travel graph. From it were computed the speed of seismic waves in various layers below the surface and depth to each different seismic layer below the shotpoint. In the case of the Oso dam site it was possible, in addition, to determine the depths below certain geophones, because there were only two seismic layers involved. Interpretation In seismic exploration waves are refracted from the top of layers which often correspond to divisions between subsurface formations. When drill holes are available the geologic logs offer a means of correlating stratigraphic breaks with seismic layers, improving reliability of seismic interpretation in terms of depth to bedrock or other geologic terms. There were no drill holes available in the case of the work at the Oso dam site. Geologic conditions appeared favorable for seismic technique because of excellent contrast in seismic wave velocity between the overburden and the Mesa Verde formation. The upper layer had a velocity of approximately 2500 fps and was interpreted as overburden, the lower layer had a velocity of approximately 9000 fps and was assumed to be the sandstone. These velocities are of the order expected in these materials. The seismographs obtained at the Oso dam site were excellent. The energy from the shot came in strongly at each geophone, giving an easily read record. Time-travel graphs plotted from wave arrival times were uniform and made interpretation comparatively easy. In Spreads 1 and 2 near the river the lower velocity layer was 12 to 15 ft deep. For the spreads on higher ground, or the bench south of the river, it was from 15 to 29 ft deep.

Jan 1, 1952

By R. E. Hobart

THE development of the Hauto power plant and the claims made by various engineers that electricity was more economical than steam for power purposes in and about the mines; led the Lehigh Coal and Navigation Co., in 1911, to conduct a test to ascertain the consumption of power used by a large steam hoisting engine. The question being one on which no reliable information could be found, and the opinion of various engineers differing to such an extent, it was decided that a test under actual operating conditions was necessary. This was arranged for at one of the collieries. The engine selected was a 30 by 60-in. (76.2 by 152.4-cm.) piston-valve engine of modern type, and comparatively new. The boiler plant from which the hoist received its power was about 600 ft. (182 m.) from the engine, the latter being fed by a 10-in. (25.4-cm.) steam line insulated with magnesia pipe covering. Two batteries of the boiler plant, aggregating 1200 hp., were cut off and fed into a separate steam line leading direct to the hoist engine. Steam auxiliaries, consisting of feed-water pump and blowers, were fed by the boilers in test, and their consumption charged against the hoist. A barrel weighing device was installed, as it was felt that this would be the most accurate way of determining the consumption of water. The fuel, No. 3 buckwheat, was carefully weighed, and every precaution was taken to make the test accurate in every particular. The test was run for 1 week, or a total of 168 hr. A record was kept of the number of trips hoisted or lowered, and continuous indicator cards were taken. One particular set of cards was taken with the hoist operating balanced, and also with the hoist operating with no counterweight other than the empty cage, the coal in the car being weighed. The speed of the hoist was taken by means, of a graphic recording instrument which registered the number of revolutions every 5 sec. From this record, speed-time curves were plotted.

Jan 2, 1918