Search Documents

By F. Wald, A. J. Rosenberg

The general features of the constitution of the B-Pt system were determined using standard rnetal-lograph~c, thermoanalytic, and X-ray diffraction techniques. Three compound were found. Two of these, Pt3B and Pt,B, are formed by peritectic reactions at 523° and 890°C, respectively. The third, Pt3B,, is congruently melting with a flat maximum at 940°C but decomposes eutectoidally in to Pt,B ant1 boron nt - 600° to 650°C. THE low-temperature allomorph of boron (red, simple rhombohedra1 a boron) is of scientific and technological interest as an elemental semiconductor.' However, the studies of this material have been hampered by its reported instability above 1200"~ which precludes crystal growth from the melt (mp - 2200°C). Crystallization from platinum solutions has been suggested as an alternative crystal-growth technique, but has met with only limited success.' The technique depends upon the existence of a significant difference between the eutectic temperature and the transformation temperature of boron. In order to clarify the conditions for further crystal-growth experiments, we found it desirable to redetermine the main features of the B-Pt phase diagram since previous reports on the system1'5'6'7 are in marked disagreement. EXPERIMENTAL The experimental methods used were thermal analysis, metallography, X-ray analysis, and, to a lesser extent, measurements of microhardness. Most of the alloys were prepared from spectrograph-ically standardized boron obtained from Johnson-Matthey &Co., Ltd. (212 ppm impurities, exclusive of carbon and oxygen) and platinum powder obtained from F. Bishop & Co. (200 ppm impurities, mainly of other platinum group metals). Some alloys were also prepared with very high-purity, float-zone refined boron (99.9999 pct obtained from "Wacker Chemie" and extrahigh-purity platinum (99.999 pct) obtained from Johnson-Matthey & Co., Ltd. The reported results did not depend on the choices of these starting materials. Five-gram alloy specimens containing 10, 20, 25, 27.5, 30, 33.3, 34, 35, 37, 37.5, 38, 39, 40, 41, 42, 43, 45, 50, 55, 60, 70, and 80 at. pct B were made by melting the elements together in boron nitride crucibles using rf heating of a graphite susceptor, either in vacuum or under high-purity argon. All alloys were heated to at least 1800°C for -5 to 15 min. Most of the alloys did not wet the crucibles when the latter were outgassed by preheating under vacuum. In any event, no weight loss was detected after melting, and the nominal composition was assumed for all specimens. Thermal analysis on 2.5-g samples were carried out in boron-nitride crucibles under a vacuum of 5 x X torr. The apparatus was heated in a "Kan-thal A 1" wound furnace, which limited the maximum temperature to about 1100°C. The output of the indicator thermocouple was fed to a dc recorder with a 1-mv full-scale span and an adjustable zero. The apparatus was calibrated repeatedly, using the freezing points of high-purity aluminum, silver, and gold. The results justified the use of the NBS voltage vs temperature tables for Pt/Pt 10 pct Rh thermocouples. All thermal analyses were run at least twice and both the heating and cooling effects were recorded. Most of the alloys had a very strong tendency to supercool. However, the use of mechanical vibration permitted reproducibility within *5°C for all alloys, except in the region around 40 at. pct B. Only the cooling effects are plotted in Fig. 2, since they appear to be more reliable. For metallography, the alloys were cut with a diamond cutting wheel, cast in a polymethacrylate resin, ground and polished with diamond paste, and etched with dilute aqua regia, a common etch for platinum alloys. Both copper and molybdenum radiation were employed to obtain X-ray diffraction data using Debye-Scherrer cameras and a "Norelco" diffractometer Diffractometry with high scanning speeds (1 deg per min) using nickel filtered CuK, radiation was used to identify the main regions of the diagram. However, molybdenum radiation was used for the detection of boron, since the latter showed very strong absorption and fluorescence effects with CuK, radiation. RESULTS AND DISCUSSION Three intermediate compounds, corresponding to the compositions Pt3B, Pt2B, and Pt3B2, were found in the system. Fig. 1 reproduces their X-ray diffraction spectra, together with those of pure boron and pure platinum. As can be seen from the thermal-analysis data in Fig. 2, Pt3B and Pt2B are formed by

Jan 1, 1965

By Voyle R. McFarland, Robert A. Burmeister, David A. Stevenson

The distribution of lead between phases in the Ag-Sb-Te system was studied using microautoradio -graphy. Two compositions were investigated, both containing an intermediate phase Known as silver antimony telluride as the major phase, and one containing AgzTe and the other SbzTes as the minor phase. For both compositions, two thermal treatments were used: nonequilibrium solidification from the melt and long equilibration anneals of the as-solidified structure. For each composition, lead was segregated in the minor phase of the as-solidified structure, but was distributed in the matrix after anneal. The electrical resistivity and carrier type were insensitive to the distribution of lead in the two-phase structure. ThERE has been considerable interest in the Ag-Sb-Te system because of its thermoelectric properties. The major interest has been in compositions on the vertical section between AgzTe and SbzTes, particularly the 50 mole pct SbzTes composition AgSbTez (compositions are conveniently expressed as mole percent SbzTes along the AgzTe-SbzTes section). One of the major problems in the proper evaluation and utilization of this material is the inability to control the electrical properties through impurity additions: all alloys prepared to date have been p-type, even with the addition of large amounts of impurities. It has been shown Wit all the compositions previously studied contain an intermediate phase of the NaCl st'ructure as a major phase (denoted by b) and a second phase, either AgzTe or SbzTe3, as a minor phase.'-3 One explanation for the unusual electrical behavior of this material is that the impurity additions have a higher solubility in the second phase than in the matrix; the impurity would segregate to the second phase, leaving the bulk matrix essentially free of impurity.4 In order to investigate this mechanism with a specific impurity element, the distribution of lead between the two phases was determined using autoradiography. Lead 210 was chosen because of the suitability of its 0.029 mev 0 particle for autoradiography and also because of the interest in lead as an impurity in this system.5'6 EXPERIMENTAL PROCEDURE Two compositions were taken from the vertical section between AgzTe and SbzTes, 50 mole pet SbzTes (Viz. AgSbTez) and 75 mole pct SbzTes, in which AgzTe and SbzTes appear, respectively, as the minor phase. Lead containing radioactive lead (pb210) was added to the above compositions to provide a concentration of 0.1 wt pct Pb. The material was placed in a graphite crucible in a quartz tube which was then evacuated and sealed. The samples were melted and solidified by cooling at a rate of 8°C per min and then removed and prepared for microa~toradiography. After autoradiographic examination of these samples, they were again encapsulated and annealed in an isothermal bath at 300°C for a number of days and prepared for examination. An alternate method of preparation employed a zone-melting furnace; the molten zone traversed the sample at a rate of 1.2 cm per hr and the solid was maintained at a temperature of 500°C both before and after solidification. This treatment had the same effect as solidification at a slow rate followed by an anneal for several hours at 500°C. In order to obtain the best resolution, thin sections of the alloy were prepared by hand lapping to a thickness of approximately 20 p. Other samples were prepared for examination by lapping a flat surface on the bulk sample. The resolution, although somewhat better in the former procedure, was adequate in both instances and the majority of the samples were treated in the latter fashion. A piece of autoradiographic film (Kodak Experimental SP 764 Autoradiographic Permeable Base Safety Stripping Film) was stripped from its backing, care being taken to avoid fogging due to static-electrical discharge. A small amount of water was placed on the sample, the film applied emulsion side down on the surface of the sample, and the sample and the film dipped into water in order to assure smooth contact. After drying, the film was exposed for 2 to 5 days, the period of time selected to give the best resolution. The film was developed on the specimen and fixed and washed in place. Two major factors must be considered in establishing the reliability of an autoradiograph: the in-

Jan 1, 1964

By B. G. Matson, M. A. Whitfield, G. R. Dysart

This paper describes the development of u computer program to calculate changes that occur in the length of tubular goods due to temperature and pressure changes during stimulation operations. Due to the numerous variables involved and the uncertainty of all static and dynamic conditions that could exist, it becomes a staggering task for individuals charged with completions to perform the necessary mathematical calculations. The computer program permits advance calculations for several sets of conditions. INTRODUCTION In the Delaware basin of West Texas alone, 50 wells were contracted or drilled to 15,000 ft or deeper in 1965. Deep well activity is continuing in this and other areas on an expanding scale. Many of these deep wells require extensive stimulation for successful commercial production, and during these operations, pressures and temperatures are encountered that have a pronounced effect on the length of tubular goods. This length change during a large-volume, high-pressure stimulation treatment utilizing fluids considerably cooler than bottom-hole temperature can be of such a magnitude that permanent damage to casing and tubing will result unless mechanical design, pressures and fluid temperatures are evaluated and controlled. These pressure and temperature effects can be calculated. However, the process lends itself well to computer solutions because of the mathematical nature of the problem and the calculating hours involved in arriving at an answer. The engineering-hour demand becomes more severe as tapered strings are involved. On initial treatments on a given well, surface pressure and injection rate conditions are unknown, and offset well conditions have not proven to be a reliable method for making predictions. For these reasons, it has become rather standard procedure for operators to compensate for these uncertainties by placing unnecessary pressure and fluid temperature restrictions on stimulation design. On a number of occasions treating fluids have been preheated to as much as 160F as a means of compensating for thermal contmction resulting from pumping cool fluids. The maintenance of packer seals has been treated by Lubinski, Althouse and Logan',' and the problem of therma1 effects on pipe has been explored by Ramey." These works were expanded and the results made applicable to everyday oilfield terminology before submitting them to computer programming. The pressure and temperature effects on tubing movement previously mentioned occur simultaneously as fluid moves through the pipe. The pressure changes, for purposes of explanation, are categorized here as to the various effects these pressures have on a tubing string. These divisions are (1) the piston-like results of forces acting on horizontal surfaces exposed to pressure, (2) swelling or ballooning of the tubing along its entire length due to the forces of pressure acting against the tubing walls, (3) the elongation of tubing due to frictional drag and (4) corkscrewing of the pipe due to internal pressure. Thermal changes are also of great importance, as their results may be more significant than any of the pressure effects. Steel is an excellent conductor of heat and the earth is a relatively poor conductor. It has been calculated that pipe temperatures at depths of more than 20,000 ft approach within as little as 25" the temperfature of the surface fluid after pumping for 2 hours, or a drop in temperature in some treatments of more than 220F. The equations presented in this paper were developed for computer programming and simplicity of input information; therefore, numerical constants such as Young's modulus for steel (28 X 10\ si), the coefficient of thermal expansion of steel (6.9 X 10."IF) and Poisson's ratio for steel (0.3) are included with unit conversion factors. The moment of inertia of tubing cross-sectional area with respect to its diameter was changed to a constant times (D' — d') where D is outer diameter and d is inner diameter. Units in the equations are length in feet, diameter in inches, density in pounds per gallon, pressure in psi, rate in barrels per minute and time in hours. PISTON-LIKE REACTIONS A change in tubing internal dimensions and the exposure of other horizontal surfaces to different pressures on the inside and outside of the tubing result in a reaction much like a piston under pressure. Such is the case when the internal diameter changes in a combination string of pipe, when seals of a slick joint assembly are subject to pressure and in the end effects of a tubing string. The change in tubing length due to the piston effects of a slick joint packer is affected by the various diameters involved, the tubing pressure Ap,, the casing pressure ,Ap,, length of pipe L, densities of fluid in the tubing before and during pump-

By Robert L. Slobod

In much of the work reported in the literature on long cores. true connate water value, probably have not been obtained because of insufficient flow of 011 to attain equilibrium. A -.satisfactory method for establishing connate water in long cores has been developed in which oil flow is maintained until no additiona1 water is displaced. INTRODUCTION Long cores have been used by sev-erals investigators in an effort to evaluate the efficiency of oil recovery for various producing schemes. The effects of many variables such as rate of displacement. pressure drop, volume of displacing medium, gas-oil ratio, inter-facial tension, and others have been investigated, and the merits of gas drive have been compared with water drive. In the older experiments no connate water was used. but in the more recent stndies the philosophy of the experiment calls for a core containing oil and connate water (irreducible water) as the starting point of the experiment. The method generally used to establish this condition in long cores involves dynamic' displacement wherein one or more phases are forced through the core. flow being maintained at a constant rate or at a constant pressure until a steady state is reached wherein there is no change of saturation with time. It is one purpose of this paper to point out that in much of the work reported in the literature true connate water values probably have not been obtained. The reason for this failure is pointed out. and a method for obtaining more reliable connate water values on long cores is presented. It is impossible at this time to completely evaluate the effect on the conclusions in the earlier papers resulting from the failure to obtain true connate water in the long cores, but some data are presented which indicate that serious errors may he present in many cases. MATERIALS AND APPARATUS Cores cut front outcrop sandstones (Strawn. Torpedo, and Elgin sandstones) with permeabilities of the order of 300 md were used. The major experiments were made with a core 18-in. long and 2-in. in diameter. Cores of the same diameter but only 12-in. long were used in a few tests? and in some work a core I-in. in diameter and 11-in. long was used. These materials were all somewhat bentonitic. 'To reduce the effect of such constituents, one of the cores (Torpedo No. 10) on which the most work was performed was acid extracted at the start of the experiment. Brine containing 50,000 ppm chloride and naphtha (Stoddard's Solvent) were used as the water and oil phases, respectively. The core was mounted in a rubber sleeve which forms the inner lining of a brass cylinder. In this arrangement2 the rubber sleeve is forced against the core by applying pressure to water in the annular space between the rubber sleeve and the brass cylinder wall. The core is therefore sealed in rubber so that all fluids introduced at the input end of the core flow through the core. With this equipment the core may be easily removed for inspection and analysis. Also, other cores may be introduced for study with no extra time for preparation such as is required when plastic mounting is used. When pressure or conductivity measurements are desired at intermediate points along tile length of the core, the brass cylinder comprising the outer jacket of the core holder is cut into section, of the desired length. Each section is then made up as an individual unit with its own rubber sleeve (see Fig. 1). The individual units are then butted up against a ring of plastic or other insulating material which carries an electrical contact for resistivity measurements and an opening which can be used for the measurements of fluid pressures. The individual units are forced tightly against the plastic ring separators and held in place with several tie rods. Inlet and outlet end butts of the same diameter as the core and several inches in length are provided to control the introduction and withdrawal of fluids and to complete the arrangement for sealing the core within the rubber sleeve. Fluid flow is maintained either by applying pressure to the liquid confined in a reservoir or by the use of a gear pump. The latter is preferable where continuous flow at a moderate rate over a long time interval is desired since a small volume of liquid can be readily recirculated using filters to prevent plugging of the core. EXPERIMENTAL The oven-dried core is weighed and is then completely saturated with brine

Jan 1, 1950

By P. G. Shewmon

A novel technique for determining the surface energy (?) and its derivative with respect to orientation, (?') is described. Essentially it involves the 'floating" of a wedge on the substrate, said wedge being made of a material which is not wet or only slightly wet by the substrate, i. e., as a greased needle "floats" on water. A thermodynamic analysis of a system in which the wedge is supported entirely by surface energy is given. If the original suyface is not at a cusp orientation, the surface tension is directly measurable from the groove angle formed. If the original surface is at a cusp orientation, there may or may not be a groove depending on the relative value of ?' and the weight of the wedge. Experiments primarily on copper and silver showed that sapphire, quartz and refractory metal wedges were wet while graphite wedges were not. The technique was demonstrated to work using graphite wedges, but the results obtained were not as eccurate as those obtained by other workers using the wire-creep experiments. It is concluded that the technique might prove most useful with non-metals where ?' is large and filament creep experiments would be quite difficult. If an absolute value of the surface free energy (?) of a metal is to be determined, the most reliable methods used to date measure an average over the various orientations exposed on a polycrystalline sample. For example, ? for silver, gold, and copper have been measured by determining the force required to just keep a thin wire,' or foil,' specimen from contracting under the influence of ?. Herring 3 has predicted and experiment confirms, that the sensitivity of this method is inversely proportional to the grain size.' Thus it cannot be used to measure ? for a particular orientation by using a foil single crystal or a very coarse-grained specimen. An accurate value if ? for tungsten averaged over a range of orientations has been determined using a field emission technique. The same techniques cannot or have not been used to measure ? for non-metallic solids, and as a result the values available are much less accurate.4 This Paper resents a means of making an absolute determination of ? for a particular surface orientation on any solid, as long as the given surface orientation does not break up into other orientations during an anneal. Experimentally ? is found to vary with orientation and at a few low index orientations it is found to have a cusped minimum, i.e., the derivative of ? with respect to the orientation of the surface changes discontinuously at the low index orientation, see Fig. 1. The slope of a plot of ? vs orientation (herein designated ?') is called the torque on the surface, since it tends to rotate the exposed surface toward the low index orientation, or if the surface is at the cusp orientation it opposes any force tending to rotate the surface out of the low index orientation. The ratio ?'/? has been determined for a few metals, but in cases where this ratio is high there is presently no means of determining either ?'/? or the absolute value of ?' for the orientations present on an annealed surface. The technique discussed herein also provides a means of determining an absolute value of ?' for those orientations which deviate only infinitesimally from a cusp orientation. It should work best on surfaces where ?'/? is large; that is, for cases where no other technique is available for measuring ?'. Aside from trying to learn more about surfaces through measuring ? and ?', the primary reason for wanting values of ? or ?' is to study adsorption. From measurements of the variation of ? for a particular orientation with the concentration of an impurity, one can obtain the number of impurity atoms adsorbed per unit area (Ti) on that orientation using the Gibbs adsorption equation.' where µi is the chemical potential of the adsorbed impurity. Thus, if absolute values of ? could be obtained for the free surface of a given surface orientation as a function of µi, ri could be determined for the given orientation. Furthermore, by equilibrating a grain boundary with the given surface at various values of ki, one could also determine ri for the grain boundary. Similarly Robertson 6 has pointed out that if y is taken to be a continuous function of and µi, then a2 ?/a @a µ2 = a2 ?/a pi a +. Thus, at all orientations away from cusps the following equation holds From a measurement of ?' vs ki, it is thus possible

Jan 1, 1963

By J. Campbell

Various models are discussed for the evaluation of the negative pressures which may occur in solidifying materials which exhibit various deformation modes: elastic-plastic, Bingham, viscous, or creep flow. The inadequacy of the previously proposed elastic-plastic solution for solidifying metals is revealed by comparison with the more reliable creep results which are given graphically for aluminum, copper, nickel, and iron. The maximum tensions experienced in the liquid phase of solidifying spheres ranging in size from large castings to submicron powders are in the range from —10' to —105 atm for these metals. THERE has been much recent interest in the negative pressures associated with the volume change on solidification and in the possibility of the occurrence of cavitation. Considering the freezing of a highly supercooled liquid, an attempt to evaluate the stresses in the liquid ahead of the rapidly moving solidification front has been made by Horvay1 on a microscale and by Glicksman2 on a macroscale. In a casting of a wide freezing range alloy, the pressure differential due to viscous flow of residual liquid through the pasty zone has been discussed by Piwonka and Flemings,3 In a previous publication4 the author has attempted to estimate the negative pressure occurring in the residual liquid of a spherical casting, employing an elastic-plastic model to describe the collapse of the solidified shell under the internal tension. An earlier model assuming a rigid shell was shown to be inaccurate by many orders of magnitude. The elastic-plastic model is critically reviewed here, and other models are developed which are thought to be more closely related to metals and other materials near their melting points. The spherical geometry (Fig. 1) is chosen because the highest shrinkage pressures would be developed, although the analyses are readily adaptable to cylindrical geometry. A parallel sided casting experiences little internal tension because of the relatively easy dishing inward of the sides. (This commonly observed phenomenon has previously been attributed solely to atmospheric pressure.) Furthermore, small regions of confined liquid in a large solidified volume of a casting approximate reasonably well to spherical geometry. ELASTIC-PLASTIC MODEL The author has shown4 that as solidification proceeds the internal hydrostatic tension builds up until the elastic limit of the shell is exceeded. At this point the internal pressure is closely -2Y/3. Subsequently a plastic zone spreads from the inner surface toward the outer surface of the shell. When the whole casting is deforming plastically a rather more generalized analysis taking account of the externally applied pressure PA + 2y/b gives the internal pressure as: P = Pa + 2y/a + 2ys/b - 2 Y In(b/a) [1] The 2y/a and 2ys/b terms result from the tendency of the liquid-solid and solid-vapor interfaces to shrink, reducing their energy, and thereby helping to collapse the solid phase and compress the liquid phase. The 2y/b term would be important only for powders. The last term arises because of the plastic restraint of the solid, resisting collapse and so effectively expanding the residual liquid. From Eq. [I] it is easily shown that there is a minimum in the pressure at the radius amia= y/Y [2] which is of the order of 103K for the metals aluminum, copper, and iron, and corresponds to the minimum pressure Pmin = 2 Y[l-ln(bY/y [3] The results of a fully worked out elastic-plastic solution are given in a previous reporL4 The main criticism which may be leveled at this analysis when applied to metals at their melting points is the strong dependence of the yield stress on the strain rate. The strain rate varies with both solidification conditions (e.g., whether chill-cast or slowly cooled) and during solidification, as is indicated in the following section. Thus an appropriate choice of Y is very arbitrary. Before proceeding to a discussion of models which are strain-rate-dependent, it is necessary to evaluate the strain rate as a function of the rate of solidification. SOLIDIFICATION RATE Various empirical relations have been deduced5 for the rate of thickening of the solid shell by pour- out tests on partially solidified spheres. These, however, are unsatisfactory for our purposes since they become very inaccurate when the liquid core is very small. A theoretical approach is therefore necessary, and some solutions are set out below. Making the assumptions of constant surface temperature of the casting during freezing, no superheat, and a material freezing at a single temperature, Adams8 deduces the approximate solution: which becomes when b » a: Employing a semiempirical approach vallet6 finds:

Jan 1, 1969

By ED. E. Furman, R. H. Atkinson

HITHERTO the practical creep testing of precious metals has received little or no attention. The only previous creep tests of precious metals have been made with wires under conditions such as to yield much more rapid rates of creep than in engineering tests.', ' Up to the present time the value of creep bars of adequate size, in the absence of real need for engineering data, has deterred investigators. However, the increasing use of platinum at high temperatures has demonstrated the need for reliable creep data for the guidance of engineers, especially those engaged in designing certain specialized chemical plant equipment. In order to supply this need, creep tests were conducted at 1382°F (750°C) on 0.290 in. diam specimens of platinum, 90 pct Pt, 10 pct Rh and palladium. The platinum was high purity, nominally 99.95 pct Pt. The 90 pct Pt, 10 pct Rh was of the same high quality as is used for making gauzes for the catalytic oxidation of ammonia. The palladium was also of high purity; two batches of palladium bars were tested, one deoxidized with calcium boride and the other with aluminum. Spectrographic examination of the palladium confirmed its good quality; the only significant impurities apart from the residual deoxidizers were traces of silicon and lead. Procedure The creep bars, which were furnished by Baker and Co. to our specification, were 6 ¾ in. in overall length with a 4½ in. (4 in. gage length) reduced section 0.290 in. in diam and had the ends threaded (?-NC16). It may be of interest that the bars were valued at up to $600 each. The specimens were supplied in a 50 pct cold-worked condition to facilitate attachment of the creep extensometer, which was of the push rod type. Because of the softness of the platinum and palladium, the extensometer rings were secured to the test section by means of circular knife edges instead of the usual pointed set screws. The extensometer rods extended through the bottom of the furnace and readings were taken with a 0.0001 in. "Last Word" dial gage fastened to the rods for the duration of the test. The bars were directly loaded by hanging weights from the lower specimen grip. All tests were conducted at 1382°F ± 2°F, and an effort was made to maintain the temperature gradient over the test section within 2°F. The ends of the furnace tube were packed with asbestos wool, which allowed a very slow circulation of air through the tube. Annealing was accomplished in the creep furnace before the load was applied. The platinum and palladium specimens were annealed at the test tem- perature for about 17 and 24 hr respectively; in the case of the rhodioplatinum it was found expedient to anneal for 1 hr at 1922°F (1050°C). Pilot samples cut from the same stock as the bars were used to check annealing procedures. Pertinent measurements of grain size and hardness were recorded. Results and Discussion The creep data obtained are given in Table I and the creep curves are plotted in Figs. 1, 2, and 3. Two platinum specimens, tested under a stress of 250 psi, had almost identical creep rates at 2000 hr, namely 0.000008 and 0.000009 pct per hr. A third platinum specimen, stressed at 400 psi, had a creep rate at 2000 hr of 0.000026 pct per hr; the reason for a rather sharp decrease in creep rate during the period from 1200 to 1600 hr is unknown. As it was thought that 90 pct Pt, 10 pct Rh would have a lower creep rate than platinum, the first sample was tested at 400 psi; however, the creep rate was approximately 50 pct greater. Microex-amination revealed that differences in grain size might be responsible for the unexpected result, as annealing at 1382°F developed an average grain diameter of 0.0021 in. in the rhodioplatinum specimen compared with 0.004 in. in the platinum bar. Annealing the alloy for 1 hr at 1922°F (1050°C) increased the average grain diameter to 0.0032 in. and materially improved the creep resistance, making it much better than platinum. A second specimen annealed at 1922°F (1050°C) and tested under a stress of 550 psi had a creep rate of 0.000022 pct per hr at 2000 hr, which was still substantially lower than that shown by the specimen annealed at 1382°F (750°C) and stressed at only 400 psi. In contrast to the creep behavior of the platinum and rhodioplatinum specimens, the palladium bars, whether deoxidized with calcium boride or aluminum, were characterized by high first stages of creep. However, after about 1200 hr of test, the creep

Jan 1, 1952

By H. R. Froning, R. O. Leach

In wertability alteration flooding, a chemical agent is rnoved through a reservoir by the flood water to increase oil recovery by decreasing the degree of wetting of the rock by the oil. Substantial amounts of the chemical may be lost during movement through the reservoir. The extent of the loss, and therefore the economics of the process, depends in some cases on factors which are difficult to reproduce in the laboratory. Therefore, a short-duration, low-cost field test method is needed to permit evaluation of chemical requirements under actual field conditions. This paper describes a small scale rest conducted at a single well for measuring chemical requirements, thereby giving a more reliable evaluation of this important factor in the applicability and economics of the process. In the rest a small wafer slug containing the chemical agent and a nonadsorbed tracer is displaced into the reservoir by a known volume of wafer. The well is then placed on producrion. Chemical loss per barrel of pore volume contacted is calculated from [he fractional recoveries of the agent tested and the nonadsorbed tracer. The method has been used to determine within the actual reservoirs the chemical requirements for both a sandstone and a dolomite reservoir. Several chemical agents are potentially available for wettability alteration flooding, although none is universally applicable. For some applications of the method, chemical costs per barrel of additional oil recovered can be substantially less than one dollar. INTRODUCTION Wettability alteration flooding provides a means of increasing oil recovery from reservoirs by decreasing the degree of wetting of the rock by the oil and increasing the displacement efficiency of the flood water. Earlier studies demonstrated a relationship between oil recovery during waterflooding and the degree of wetting of a rock surface by an oil. The application of wettability alteration flooding to the Harrisburg field of Nebraska provided a field test' of this recovery process. Subsequently, additional laboratory and field tests have developed additional procedures for evaluating wettability alteration flooding, and have indicated where the process may be applicable. Applicability of this process to specific reservoirs is determined by a progression of tests to determine sus- ceptibility of the reservoir to alteration of its wettability, to indicate the degree of recovery improvement and to estimate the amount of chemical required to process the reservoir. The economics of applying improved oil recovery processes depends not only upon the degree of improvement in oil recovery achievable by the process but also upon the process costs and the timing of the income and the investment. Emphasis in this paper is on the expenditure aspects of the process. The work reported in this paper indicates that the chemical investments required for wettability alteration flooding are substantial. For evaluating the economics of a potential flooding application it is imperative that a sound estimate of the chemical requirements be made for the reservoir. Generally, true reservoir conditions are not adequately simulated in laboratory chemical propagation tests. Because of wide well spacings, many years might be required to obtain chemical propagation data from conventional pilots or inter-well tests. Consequently, n short-duration, low-cost method is needed to determine chemical requirements in the field. The potential applicability of wettability alteration flooding is discussed, as well as the economics of wettability alteration with respect to the inherent and imposed restrictions on the timing of income and investments. DETERMINATION OF CHEMICAL REQUIREMENTS In the process of moving a chemical bank through reservoir rock, some of the chemical agent lags too far behind the flood front to be effective or is otherwise lost to the reservoir system. The extent to which these losses occur overshadows the reductions in chemical concentration due to diffusion and to mixing with the reservoir fluids. Experience indicates that almost without exception, chemicals which induce a wetting change undergo either sorption reactions or chemical reactions with mineral constituents of the pore surfaces. Other reactions may occur between the added chemical and the reservoir oil and water. Even in limiting consideration to reactions of the relatively inexpensive inorganic salts, bases and acids, the reactions may be exceedingly complex. Reservoir pore surfaces consist of more than silica in sandstone reservoirs, and more than calcite or dolomite in carbonate reservoirs. Many mineral species are present, each exhibiting specific tendencies to react with an injected chemical. The reactions which occur can consume enough of the agent to have an important effect on economics. These reactions can cause a change in pH of the chemical bank, or may remove some of the active chemical by precipitation, adsorption or reaction to form a new chemical which may or may not be effective in

By M. R. J. Wyllie

Eight laboratory-prepared aqueous base drilling muds representing common mud types, and 15 aqueous base drilling muds sampled in the field, have been used in an experimental investigation of the relationship between the streaming potential developed across a mud filter cake and the differential pressure causing filtrate flow. It has been established that the relationship is of the form, ES = kPy, where Es is the streaming potential, P the differential pressure and k and y are constants for any particular mud system at constant temperature. Beyond a certain minimum thickness this relationship is independent of filter cake thickness. Experiment has shown that both k and y are temperature dependent parameters and that in certain mud systems there is a critical value of P above which the simple relationship Es = kPY ceases to hold. The constant k tends to be a function of the mud resistivity at 77ºF, but the exponent y has not been found to be related to any commonly measured mud property. Certain field experiments are described which serve to demonstrate that the total SP (self potential) developed opposite a formation may be quantitatively accounted for as the algebraic sum of an electrochemical potential and an electrokinetic potential. A chart to permit the simple use of mean solution activities in the interpretation of electrochemical SP data is given and its use described. Various field methods for computing the electrokinetic SP component of the total SP are considered and rejected as being unduly complicated and inaccurate. It is shown that the employment of low resistivity drilling muds is essential if optimum accuracy is desired in the use of the S.P. curve for the purpose of computing connate water salinities by the electrochemical SP method. The use of such low resistivity drilling muds is accordingly recommended. INTRODUCTION In a previous paper' a quantitative analysis of the electrochemical compovent of the SP (self potential) curve was made and it was shown that the electrochemical* emf, E, could be expressed as E = ZtRT/F In a,/a,, where t is the transference number of the chloride ion, R is the gas constant, T the absolute temperature of the formation water and mud, a, the mean activity of the connate water (assumed to be sodium chloride) and a, the mean activity of the mud (as sodium chloride). The essential accuracy of this expression was confirmed by an investigation 2 of the SP kicks opposite sands of known water salinity. The logs examined had been routine runs in oil wells in a number of Mid-Continent states. Further confirmation of the original analysis of the electrochemical SP is implicit in the paper by Tixier3 wherein a relationship between the SP and the ratio of connate water and mud resistivities, based only on field data, is given. Allowing for the fact that mud and connate water resistivities were used instead of activities, and that electrokinetic effects were ignored, the constant reported by Tixier is essentially 2tRT/F. The error involved in the universal substitution of resistivities for activities will receive further reference below. Possible reasons for the fact that the electrochemical properties of shales do not appear to be significantly dependent upon either the nature or the quantity of cation exchange materials, such as clays, they contain has been considered at some length by Wyllie and Patnode.4 In the same paper, the probable effects of shale thickness and compaction on electrochemical efficiency, and hence the inherent difficulty of obtaining reliable laboratory-scale data, were also pointed out. However, it is

Jan 1, 1951

By J. T. Dewan

An experimental setup is described whereby the responses of Neutron logging instruments have been determined opposite formations of different porosities and under various borehole conditions. The results of these tests are presented in several charts which show how the Neutron log is affected by the following factors: hole diameter, casing, cement, salinity and weight of drilling mud, and position of logging tool with respect to the wall of the hole. The responses in the case of empty holes are also shown. A chart is furthermore presented which shows the shapes of the Neutron log, as a function of logging speed and time constant, at the boundaries between two formations with different porosities. These were derived mathematically using as a basis laboratory determination of the shape of the curve under static conditions, i.e. at very low logging speed. Corrections for the readings made opposite thin beds are given by these computations. The correction is found negligible under usual logging conditions for beds thicker than about 4 ft. INTRODUCTION The Neutron log is used in borehole surveys both for the delineation of porous formations and for the quantitative estimation of their porosities.1,2,3,4,5 It is common practice to calibrate the response of the Neutron log in terms of porosity values for each given geological unit by means of empirical comparisons between the deflections of the neutron curve and the porosity values given by the core analysis in a sufficient number of wells. Usually, the plots of the porosity values vs Neutron log deflections show a definite trend. It is therefore possible to trace an average line across the plotted points. This average line constitutes a calibration curve which can be used to evaluate the porosities from the Neutron logs in the other wells drilled in the same region. Futhermore, when the porosity values are plotted on a logarithmic scale and the Neutron log deflections on a linear scale, the calibration curve is practically a straight line. Accordingly the calibration curves are often determined by simply tracing a straight line between two points corresponding to two widely different porosities. Different choices are made for these two points, depending on local conditions. For example, one point will be defined by plotting the deflection of the Neutron curve opposite a formation known to be very tight, for which an average porosity value of 1 or 2 per cent is assumed. The other point may correspond to shale sections, to which a porosity of around 40 per cent is ascribed. The information provided by the eletrical logs — in particular the Laterolog, Limestone log or Micro-Latero-log — is also very often a help in the calibration of the Neutron logs. Empirical approaches such as these make possible the derivation of fairly reliable porosity values from the Neutron logs in many cases, at least in open holes and in essentially clean formations. There are, however, several causes of uncertainty which may sometimes entail appreciable errors. On the one hand, the Neutron log readings are influenced by the borehole conditions: hole diameter, presence or absence of casing and cement, presence or absence of drilling mud, characteristics of the mud, and position of the logging instrument with respect to the wall of the hole. The amplitudes of the curves opposite thin beds are furthermore atfected by the bed thickness,

Jan 1, 1957

By L. S. Darken

A quadratic formalism is developed lor the representation of the excess free energy, and of the activity coefficients of each component of a ternary system in the vicinity of a single component selected as solvent. This formalism, in contrast to the e formalism, is thermodynamically consistent at .finite concentrations. Numerous specific systems are used as illustrations, with cross checks where possible; these systems are Fe-C-X systems in the vicinity of 1600°C and include practically all those for which reliable data are available. It is shown that this formalism is usually quite adequate to rebresent available data up to a solute concentration of 20 to 30 at. pet. It is hoped that the formalism here presented may prove useful for the treatment and tabulation of data on ternary and multi-component solutions. SINCE, as discussed in a prior paper,' we do not as yet have an adequate basic understanding of the nature of binary metallic solutions, we cannot hope to be in better position for ternary and multicomponent systems. However, the accumulation of thermodynamic data on ternary and multicomponent metallic solutions has led to an urgent need for a rational formalism for the presentation and use of such data. Notable attempts to represent the isothermal isobaric thermodynamics of ternary solutions were made by Benedict et 01.' and by Wohl.3 These attempts were directed toward developing an analytic expression adequate to encompass the entire ternary triangle, primarily for organic systems; they generally involve the power-series approach, which has been shown' to be inappropriate, in general, even for binary metallic systems. On the other hand, interest in the thermodynamics of ternary and multicomponent metallic solutions has tended to focus either on general thermodynamic relations4-10 over wide compositional ranges, or on cases where one or more components have been at rather low concentration. This latter approach has been followed by Wagner,= by chipman,11 and by Alcock and Richardson,12 and more recently in many publications by the same and other authors. It has already been shown' that the thermodynamic behavior of binary metallic systems is, in general, relatively simple only in the terminal regions. Hence, it would appear that any approach, at this time, to a simple formalism for ternary and multicomponent systems must, a fortiori, be limited to the vicinity of the major component or solvent. The present treatment is aimed to be useful for a given solvent with moderate solute concentrations ranging up to 20 or 25 at. pet and in exceptional cases to considerably higher concentrations. In order to achieve even this modest objective, it is necessary that any appropriate formalism have built into it 1) a thermodynamic consistency (at least within the desired degree of approximation), and 2) an approach at infinite dilution to Raoult's law for the solvent and to Henry's law for each solute. Let us first formulate the condition of thermodynamic consistency for a ternary system. Under isothermal isobaric conditions, we may write for the molal value G of any extensive function dG - C1 dN1 + G2 dN2 + G3 dN3 [l] where the G's are the corresponding partial molal quantities and the N's are the atom fractions. Taking component 1 as the solvent, this relation may be rewritten in terms of the independent variables N2 and N3

Jan 1, 1968

By F. E. Jaumot, R. L. Smith

Self-diffusion in zinc has been used as an instrument for comparison of the absorption and sectioning techniques as a means of studying diffusion. Single crystal as well as poly-crystal samples were used asanda the temperature range of diffusion extended from 200° to 415°C. For temperatures above 200°C, the data indicate that the results obtained from the absorption technique agree with those obtained from the sectioning technique. The effect on the values of the diffusion coefficient of electroplating vs evaporation as a means of applying the tracer was investigated and no significant difference observed. It was found that an excess or deficiency of tracer did not materially affect the results obtained from the sectioning technique, but invariably caused errors with the absorption technique. NEARLY all self-diffusion experiments and many alloy diffusion experiments have employed radioisotopes as the instrument for following the diffusion. Of the various techniques in which radioisotopes are applicable, the two most widely used are the sectioning and absorption techniques. In the former, the diffusion coefficient is obtained from a curve of log concentration vs the square of the mean penetration depth. In the latter, the diffusion coefficient is calculated from a knowledge of the decrease in activity at the surface after diffusion. In spite of the importance of knowing the reliability of the diffusion data and the widespread use of these two techniques, they had not been directly compared experimentally on the same samples. Thus, such a comparison was worthwhile. The specific system chosen for this comparison was the self-diffusion of zinc, since the metal was readily obtainable in high purity, single crystals were easily grown, and the anisotropic features of the diffusion added an additional factor of interest to the comparison. Self-diffusion in both single and polycrystals was investigated, since the possibility existed that grain boundaries and grain boundary diffusion might produce different effects for the different techniques. Also, the effects of electroplating vs evaporation as a means of applying the radioactive tracer, and the effects of applying an excess or deficiency of tracer material were studied. The general experimental procedures and the mathematical analyses of both techniques have been described previously in some detail, and only those points essential to an understanding of the present work will be discussed here. The mathematical analysis of the sectioning data requires only a knowledge of the solution of Fick's equation. where C,, is the initial concentration, C is the concentration at depth x, D is the diffusion coefficient, and p is the absorption coefficient of the solvent metal for the radiation from the solute. Having obtained F from the experiment, the value of z can be read from a plot of F vs In z, and D can then be calculated if is known. The necessity of knowing the absorption coefficient causes most of the criticism of the absorption technique. It is very difficult to measure accurately under the conditions existing in the diffusion experiment, but it is absolutely necessary, as will be indicated briefly later. Portions of this problem have been discussed in detail elsewhere." The difficulties involved in the measurement of the absorption coefficient arise from three principle factors: the physical characteristics of the absorber, the geometry, and complex radiation spectra. The first two are heavily dependent upon the third. If

Jan 1, 1957

By M. R. J. Wyllie

Eight laboratory-prepared aqueous base drilling muds representing common mud types, and 15 aqueous base drilling muds sampled in the field, have been used in an experimental investigation of the relationship between the streaming potential developed across a mud filter cake and the differential pressure causing filtrate flow. It has been established that the relationship is of the form, ES = kPy, where Es is the streaming potential, P the differential pressure and k and y are constants for any particular mud system at constant temperature. Beyond a certain minimum thickness this relationship is independent of filter cake thickness. Experiment has shown that both k and y are temperature dependent parameters and that in certain mud systems there is a critical value of P above which the simple relationship Es = kPY ceases to hold. The constant k tends to be a function of the mud resistivity at 77ºF, but the exponent y has not been found to be related to any commonly measured mud property. Certain field experiments are described which serve to demonstrate that the total SP (self potential) developed opposite a formation may be quantitatively accounted for as the algebraic sum of an electrochemical potential and an electrokinetic potential. A chart to permit the simple use of mean solution activities in the interpretation of electrochemical SP data is given and its use described. Various field methods for computing the electrokinetic SP component of the total SP are considered and rejected as being unduly complicated and inaccurate. It is shown that the employment of low resistivity drilling muds is essential if optimum accuracy is desired in the use of the S.P. curve for the purpose of computing connate water salinities by the electrochemical SP method. The use of such low resistivity drilling muds is accordingly recommended. INTRODUCTION In a previous paper' a quantitative analysis of the electrochemical compovent of the SP (self potential) curve was made and it was shown that the electrochemical* emf, E, could be expressed as E = ZtRT/F In a,/a,, where t is the transference number of the chloride ion, R is the gas constant, T the absolute temperature of the formation water and mud, a, the mean activity of the connate water (assumed to be sodium chloride) and a, the mean activity of the mud (as sodium chloride). The essential accuracy of this expression was confirmed by an investigation 2 of the SP kicks opposite sands of known water salinity. The logs examined had been routine runs in oil wells in a number of Mid-Continent states. Further confirmation of the original analysis of the electrochemical SP is implicit in the paper by Tixier3 wherein a relationship between the SP and the ratio of connate water and mud resistivities, based only on field data, is given. Allowing for the fact that mud and connate water resistivities were used instead of activities, and that electrokinetic effects were ignored, the constant reported by Tixier is essentially 2tRT/F. The error involved in the universal substitution of resistivities for activities will receive further reference below. Possible reasons for the fact that the electrochemical properties of shales do not appear to be significantly dependent upon either the nature or the quantity of cation exchange materials, such as clays, they contain has been considered at some length by Wyllie and Patnode.4 In the same paper, the probable effects of shale thickness and compaction on electrochemical efficiency, and hence the inherent difficulty of obtaining reliable laboratory-scale data, were also pointed out. However, it is

Jan 1, 1951

By L. R. Woodyatt, H. J. Beattie, C. T. Sims

Theories correlating the formation of u and related intermetallic compounds to the electron-per-atom density of binary and ternary alloys have appeared regularly in recent technical literature. These same principles can be modified and applied to complex precipitation-strengthened alloys such as the iron-, cobalt-, and nickel-base superalloys and the stainless steels. Since these complex alloys contain carbides and other phases that normally precipitate before the U-type phases, the nature and amount of the precipitated phases must be calculated first. The following general formula is then applied to the residual matrix composition of the alloy: element. The magnitude of the resulting number is indicative of whether the alloy will form a a -type phase. When these calculations (which are computerized) are systematically applied to alloys of knoun phase analysis, a breakoff in average electron-vacancy number is noted between U-free and U-prone alloys. Alloys with an average electron-vacancy number higher than the breakoff form a-type phases, while those with lower ones do not form these phases. This method could then be used to eliminate from consideration all experimental compositions that would precipitate undesirable phases. It also is useful in evaluating analyzed heats of alloys where minor heat-to-heat variations determine whether the alloy is o-free or o-prone. THE highly significant development of strong, ductile superalloys to provide reliable construction materials in the 1000" to 2500° F temperature range has been due principally to unremitting application of Edisonian techniques and logic by the dedicated physical metallurgists who have shouldered this responsibility. Tools such as the electron microscope, phase analysis, and computers to accomplish regression analyses have been used heavily, but the effort has been essentially practice of an art, rather than a science. The objective of this paper is to describe and illustrate application of some relatively fundamental principles to certain of these alloy systems in an attempt to remove some of the empiricism from the technology. Specifically, the work presented here deals with the use of periodic-group relationships to predict the formation of intermetallic phases which can occur in primarily austenitic (fcc) structures. Calculations that have been developed might be applied in the design of new alloys and the evaluation of known alloys, and thus have the potential of eliminating vast areas of unnecessary alloy preparation and evaluation. ALLOYING CONCEPTS AND STRUCTURAL FEATURES OF SUPERALLOYS Strength is produced in austenitic superalloys by three principle mechanisms: 1) precipitation of y'; 2) formation of carbides; 3) solid-solution hardening by soluble refractory metals. The first mechanism requires the addition of aluminum and titanium, the second requires carbon and carbide-forming elements, while the third calls for the addition of molybdenum and/or tungsten. A considerable concentration of chromium is usually maintained to resist oxidation/corrosion, but it is also an important carbide-forming element. Fig. 1 shows a sketch and electron micrograph of the structure of a typical wrought nickel-base super-

Jan 1, 1967

By J. B. Stubbins, R. A. Blais

Extensive geological work was initiated — and continues — when operations of the Iron Ore Co. of Canada commenced in the Labrador-New Quebec area. Such geological operations include: mapping, test pitting, drilling, underground workings, volume factor and structure tests, and the calculation of ore grades and tonnages. Details of such work are given. Development is carried sufficiently ahead of mining to provide reliable tonnage and grade estimates and allow final mine planning. In order to make full use of geology in mining operations, the pit engineer combines the duties of geologist and mining engineer. The iron deposits of the Knob Lake range are located in the central part of the Labrador peninsula, a territory nearly twice the size of Texas, which is bounded by Hudson Bay on the west, Hudson Strait on the north, the Atlantic Ocean on the east and the Gulf of St. Lawrence on the south. The mining district proper is about 1000 miles northeast of Toronto. A 360-mile railroad links this mining area to the port of Sept-Iles on the Gulf of St. Lawrence. Schef-ferville, which is only a few miles from the open-pit mines, is the center of operations of the Iron Ore Co. of Canada. It has a population of nearly 5000. The nearest settlement is Labrador City, some 120 miles to the south, where this company is erecting a large plant for beneficiating its huge reserves of local low-grade iron ores. HISTORY The mineral possibilities of the area were recognized as early as the end of the last century, when A.P. LOW' of the Geological Survey of Canada made his famous trek across the Labrador Peninsula. After mapping several belts of iron formation, Lovr recommended that the area be thoroughly prospected for iron. In 1929, two well known Canadian geologists, J.E. Gill and U'.F. James, led a private expedition in central Labrador and discovered the first deposit of high-grade iron ore near what is now the Ruth Lake Mine. In 1936 the Labrador Mining and Exploration Co. was formed to 11ake over a prospecting concession of over 20,000 sq miles in central Labrador. An adjoining concession of 3900 sq miles in New Quebec was obtained in 1942 by Hollinger Consolidated Gold Mines, which had just Purchased the Labrador Co. The same year the M.A. Hanna Co. Purchased an interest in both exploration companies. From 1942 to 1950 extensive exploration was conducted by the Hollinger-Hanna technical staff to systematically appraise these vast concessions. More than 40 deposits of high grade ore were found and, by the end of 1950, the total ore reserves reached 418 million tons. In 1949 five American steel companies joined the Hollinger-Hanna interests and formed the Iron Ore Co. of Canada. Financing and full-scale construction were decided upon in 1950. This included the construction of a 360-mile railroad through very difficult terrain, the erection of two hydroelectric plants, the installation of terminal port facilities at Sept-IIes, the building of a modern town-site at Schefferville, the construction of crushing and screening plants, and the preparation of deposits for mining. Ore was first shipped in July 1954. Total open-pit mine production to date is 66 million long tons of direct-shipping ore. GEOLOGICAL ENGINEERING The above achievements would not have been possible without irtegrated teamwork of people of diverse skills and extensive use of geology. In their paper on the role of geologists in the development of this iron ore field, (Gustafson and Moss1 rightly emphasized the difficulties facing the early workers in the area. In an uninhabited land with no roads or railroads and no navigable rivers leading to the interior, everything had to be flown in. It was not until 1948 that aerial photographs and adequate base maps became available. In spite of these and other difficulties, an impressive amount of field work has been done since 1942. Nearly all this work has been directed by geological engineers and geologists. About 15,000 :sq miles have been geologically

Jan 1, 1962

By A. Satter, J. M. Campbell

Reported herein are the results of a careful and detailed study of the non-ideal behavior of pure gases and their mixtures. Included are: (1) new data on five ternary systems composed of methane, ethane and H2 S; (2) a simple compressibility factor correlation that is inherently superior to present correlations, particularly for gases containing H2S and CO2; and(3) a detailed study of combination rules and the effect of system composition on the choice thereof. This study makes use of the rather large mass of data already available in the literature. A complete re-examination of the data and ideas presented in the last 25 years was considered desirable as a prelude to our basic concern — the effect of diluents on gas behavior. A consideration of both the macroscopic and microscopic properties of gases provides a better insight which, in turn, gives a firmer basis for improved correlation techniques. Such a study has shown that expressing the compressibility factor Z as a function of acentric factor w, as well as reduced temperature and pressure, yields a correlation that is broader in scope. The study of various combination rules has shown that better results are obtained by "tailoring" the rule used to the system composition. To do so improves the basic reality of results by overcoming some of the anomalies often found when using Kay's rule alone. Tentative recommendations are made regarding the most reliable combination rule for use with a given class of gas. The data presented are useful for estimating the direction and magnitude of the expected deviation when using a given rule. Although more work is needed, particularly around the critical region and with CO2 mixtures, the advantage of the classification scheme proposed is apparent. INTRODUCTION When one attempts to write a PVT equation to fit the data for actual gases, greater precision is obtained by the use of a multiple number of empirical constants. This has lead to multiple-constant equations such as Benedict-Webb-Rubin, Beattie-Bridgman, Keyes, etc., which are capable of yielding very precise results for pure gases in a range for which data to get the constants are available. As a matter of practicality, though, the use of such equations for gas mixtures is limited. Because of the infinite number of gas analyses available, any attempt to compile the constants needed requires a prohibitive amount of experimental data. This could be overcome by the use of a combination rule, but there is no real advantage in doing so because the end result offers no practical impovement over the Z factor correlation. The most widely used method of predicting the volumetric properties of pure gases is based upon the "theorem of corresponding states". According to this theorem, "all pure substances have corresponding molal volume at corresponding temperature and pressure if the reference point of correspondence is the critical point". Generalized compressibility charts for gases were prepared first by Cope and associates1 in 1931 and later by Brown and co-workers2 in 1932. However, the most commonly used charts are those of Dodge,3 Nelson and Obert,4 Hougen and atsson: and Standing and Katz.6 The work of Katz and co-workers has provided us with basic data for the hydrocarbons most widely used today. Their original chart6 was compared with a relatively large amount of multi-component data for gases consisting almost entirely of normal paraffin hydrocarbons. A deviation of only + 1.2 per cent was obtained.39 In the 20 years following publication of this work it has been found that the behavior of most mixtures of paraffin hydrocarbons could be predicted by this correlation within at least 5 per cent. Where difficulty has been encountered it has largely involved one or more of the following circumstances: pressures above 4,000 psig, mixtures containing large amounts of heavy ends and/or aromatics, systems in the critical region and mixtures containing polar compounds and/or CO2. The abnormal error sometimes found with such gases, not too unexpected for this method, is

By E. H. Snow, B. E. Deal

Instability effects in semicanductor devices have long been attributed to the motion of charges on or within oxide layers on the surface. These effects are of critical importance in metal-insulator-semiconductor MIS) field-effect devices. For this reason, the capacitance-voltage or the conductance-voltage characteristic of these devices can be used as a sensitive detector to study charge transport and polarization effects in the oxide or insulator. A review is given of the results of such studies of thermally grown SiO2 as well as of other insulating films of importance in silicon technology. Three types of effects are distinguished. The first of these is the drift of mobile cations within the dielectric, examples being thermally grown SiO, which is often contaminated with sodium ions, and a variety of other glasses in which the mobile ions are a part of the glass composition. The second effect is a dipole-type polarization which occurs in phosphosilicate glass films obtained by reacting P2O5 with thermally grown SiO2. The third effect involves the transfer of charges between the dielectric and the silicon electrode. This occurs in silicon nitride and other deposited dielectrics. It is concluded that MIS studies have provided a powerful technique joy the study of charge transport and polarization effects in insulating films. The knowledge gained from these studies has led to an understanding of surface effects on conventional transistors and diodes as well as making possible stable MIS transistors. THE metal-insulator-semiconductor field-effect transistor is conceptually the oldest type of active semiconductor device.' The earliest attempts at making this device were frustrated because of high surface state densities at the interface between the semiconductor and the gate insulation.' However, by using a silicon substrate with thermally produced silicon dioxide as the gate insulation, this problem was solved and metal-silicon dioxide-silicon devices with good characteristics were made as early as 1960. 3 Yet it was still over 5 years before these devices became a commercial reality. This delay was largly due, not to surface states, but to stability problems associated with polarization effects within the insulating layer which caused the threshold voltage of the device to drift under temperature and bias treatments. The solution to these problems has not only made possible stable MIS devices, but it has added immensely to our understanding of failure mechanisms in conventional bipolar transistors and has added to the reliability of ali types of planar devices. In this review, we shall first describe the effects of various types of polarization phenomena on MIS device characteristics. Then, since thermally grown SiO, is by far the most important insulator used in these devices, we shall review historically the type of instabilities which have been observed in thermal oxides, the attempts at understanding and eliminating them, and the present status of the problem. We shall then turn our attention to the various deposited insulators which have been used, including lead glasses, phosphosilicate glass, vapor-deposited silicon oxide, and silicon nitride. Interestingly enough, many of these materials show polarization effects which are quite different from those generally observed in thermally grown SiO2. THE EFFECTS OF POLARIZATION PHENOMENA ON MIS CHARACTERISTICS The simplest MIS device and the one which has been most frequently used in the study of polarization effects is the MIS capacitor. Two modifications of this structure with single- and double-layer dielectrics are illustrated in Figs. l(a) and (b), respectively. The capacitance of this structure as a function of voltage applied to the metal gate electrode is plotted in Fig. 2 for the case of an n-type silicon substrate. When the silicon surface is accumulated (positive bias) the measured capacitance is just that of the insulating layer C. When the surface is inverted (negative bias), the capacitance is that of the insulator and a silicon depletion layer in series CoCs/(Co + Cs). Indicated on the horizontal axis of Fig. 2 is the voltage VT at which the silicon surface becomes strongly inverted. This voltage corresponds to the threshold or turn-on

Jan 1, 1969

By J. B. Wagstaff

The raceway in front of the tuyere of the blast furnace has been studied quantitatively and a correlation obtained for the penetrastudiedtion of the blast. Some evidence is presented for the height and width of the raceway which suggests that all the raceways of a ffurnace overlap. The size of the coke in this zone has been measfurnaceoverlap.ured photographically during normal operation and results are given for the various areas. IN an earlier paper,' it was shown that a raceway exists opposite each tuyere of a blast furnace. This raceway is formed by the jet effect of the air emerging from the tuyere and consists essentially of a turbulence in which coke particles are recir-culated at high speed. Its presence was deduced originally from observations on movies taken with a high-speed camera through the tuyeres of various furnaces and was confirmed by experiments made on a model. In the model described,' this raceway was shown as operating in a vertical plane only, although there was a suggestion in the motion-picture film exhibited at that time that the raceway was three dimensional, unless artificially restricted. There was also some doubt then about the factors influencing its size. This paper describes the next steps in the investigation. Since the size of the raceway is obviously of importance in the operation of the furnace, it seemed worth while to study the subject more carefully. It is probably in this region that about half the coke in the furnace is consumed, so that the movement of the stock column may well be controlled by raceway behavior. Furthermore, there is some evidence to suggest that the coke is packed densely in the center of the furnace to form the "dead man" and more loosely above the raceway. It is therefore probable that the bulk of the gases passing up the stack flow from the top surface of this raceway. Clearly then, a knowledge of this critical zone is of interest to the blast furnace operator, and the first half of this report is devoted to a quantitative discussion of the subject. A further topic of interest among operators is the degree of breakdown of coke in the furnace, with which is inseparably linked the importance of a strong coke. Indeed, the whole question of the optimum size and type of coke may be as dependent on the condition of the coke in the bottom of the blast furnace as at the top. Attempts have been made from time to time to obtain samples of coke from the tuyeres and other furnace openings but they all suffer from the fact that the coke is filled to a varying degree with metal and slag and is probably broken up by the very act of taking the sample. It has proved difficult to make any reliable studies of coke size by these methods. However, it did seem possible to use the highspeed movies mentioned earlier1 to estimate the size of the coke. These movies provide an accurate record of individual coke particles so that, in theory at least, it should be possible to measure the size of the particles one by one and to obtain, for the first time, information on the coke being blown around the raceway under actual operating conditions while the furnace is performing normally. Such a study has been made and is discussed in the second half of this paper. The results obtained enabled the blast furnace data to be correlated with the model results given in the first half. Raceway Size In order to make a quantitative study of the size of the raceway it was necessary to devise some apparatus of laboratory scale, which could be handled quickly and easily. This focused attention on models, which in turn means that the laws of similarity governing this particular process must be ascertained. Method of Procedure: Since the work was to be carried out on a smaller scale than the blast furnace, the linear dimensions of the model became unimportant provided that the scale was known; it is only important to insure that the container does not affect the raceway being observed. The studies therefore were carried out in a glass-sided box, 11 in. high x 7 in. wide x 3 in. deep, using air jets ranging

Jan 1, 1954

By G. D. Just

INTRODUCTION Large scale underground mining involves the bulk handling of fragmented material. The cost and efficiency of the mining systems is there- fore significantly influenced by material flow characteristics. Flow problems may occur in the form of ore pass blockages which interrupt the free flow at extraction openings. The costs of such delays can be readily assessed and compared to the costs incurred in reducing blockages by improved fragmentation or larger ore passes. In practice the problem is more complex than this statement suggests because it is generally un- economic to design for zero ore blockages. Another major flow problem occurs in the form of relative movement of ore and waste as the fragmented material is extracted. This produces waste dilution in the recovered ore and influences total ore recovery. This flow problem is much more complex than the ore block- age phenomena. Many questions concerning the precise flow characteristics remain unanswered because of the variability of size distributions, particle shapes, material properties and the total extraction layout and design. Model studies can provide a visual and quantitative illustration of probable flow characteristics but full scale data collection is necessary to evaluate the precision of such information. The methods and types of data obtained must be carefully selected to recover the maximum volume of useful information for operational control and future design. It is essential that honest precision levels are assigned to the data and any subsequent analyses. Grade control data may give misleading short term information on flow characteristics because of the difficulty in knowing the true grade of the mass of material before extraction commences. However, in the long term control of extraction grades is vital to the profitable operation of the mining system. The most efficient extraction design and operational schedule can only be determined after all of the facts and variables are known. This is usually only possible after the orebody has been completely extracted. However, if design and operational personnel have a full appreciation of the nature and variability of material flow under different conditions the best possible results should be achieved. The most significant features of material flow are out- lined in this paper in order to provide mine planning and mine management personnel with some of the necessary information relating to material flow. Available facts and reliable figures from selected publications are noted in association with unbiased and hopefully accurate opinions of the relevance of the data to mine design and mine system control. Possible future developments and profitable areas for research into material flow problems are also detailed. MATERIAL FLOW AND MINING METHODS The effects of material flow on the design and operation of an integrated underground ore handling system is one factor which is common to most mining methods. Analysis of the system as detailed by Just, 1980, permits the identification of unit process objectives. For example, a typical underground ore handling system as illustrated in Figure 1, involves the following unit operations:- (i) Gravity flow of ore in stope (ii) Ore extraction at base of stope (iii) Ore haulage on the production level (iv) Dumping of ore into ore pass system (v) Gravity flow of ore in the ore pass (vi) Underground crushing of ore (vii) Haulage of crushed ore to shaft (viii) Hoisting of ore to the surface. Average flow rates in each of these unit operations can be misleading due to variability in incremental capacity caused by flow blockages and machine delays. Thus to effectively analyse the probable performance of the system, it is necessary to have a measure of the flow loading and haulage rate variability. Mechanical equipment performance specifications can be used to provide such information for loading, haulage and crushing; however, in the case of the gravity flow of material field measurements are required to relate the probability of "hang-ups" to the degree of fragmentation. Factors affecting the frequency of flow stoppages are, size, distribution and cohesiveness of broken material and the geometry and size of the flow channel. Ore pass channel design is relatively simple since regular cross-sectional shapes are used

Jan 1, 1981

By T. P. Chen, F. W. Bowdish

Studies made with a captive bubble apparatus on the sulfidization and collection by amyl xanthate of true chrysocolla specimens have defined the ranges of pH value and sulfide concentration which permit contact between the bubble and the mineral surface. Titanium compounds were the most effective of the materials found to activate the sulfidization of chrysocolla. With titanium activation, the contact angles and the ranges of pH value and sulfide wncentration giving bubble contact were all increased. Chrysocolla ores were concentrated by flotation. Chrysocolla ores occur at many localities in grade and quantity sufficient to make mining and millin feasible, but no satisfactory method of concentratio has been found. Although chrysocolla may be leached with acid, only those ores without acid-consuming gangue may be leached economically. Because of its potential importance, a study of the conditions nece sary for flotation of chrysocolla has been carried ou The literature contains a few references to flotation of chrysocolla. Two methods were developed by the U. S. Bureau of Mines.1,2 The first consisted of a fatty acid soap and a high xanthate as collectors of chrysocolla from a synthetic ore, while the second involved the use of hydrogen sulfide and xanthate. Ludt and DeWitt3 demonstrated the difference in adsorptive powers of chrysocolla and quartz for bas triphenyl methane dyes and suggested the use of butyl, hexyl or octyl-substituted malachite green as collector. Jackel4 emphasized the effects of combin tions of reagents such as Aerofloat 31, pine oil, and Reagents 404 and 425 with sodium sulfide and zinc hydrosulfite as conditioning agents. Although he reported recoveries of 89% from a synthetic ore and 98% from a natural ore containing azurite, malachite, chalcopyrite and chrysocolla, careful application of Jackel's method to chrysocolla from Tyrone, N.M., failed to give a high recovery. MATERIALS AND TECHNIQUE Samples from Inspiration, Ariz., and Tyrone and Magdalena, N. M., were used for experimentation and verified as true chrysocolla by leaching tests, specific gravity tests and X-ray diffraction. Chrysocolla does not dissolve at pH 4, although malachite and azurite do. Chrysocolla is about half as dense as the copper carbonates. X-ray diffraction analyses by the powder camera method confirmed the samples as true chrysocolla. A captive bubble apparatus, which cast an enlarged image of the air bubble and the mineral surface upon a screen, was used to check on the character of the surfaces. The specimens were prepared by grinding a flat surface on a glass plate using fine abrasive; then they were washed and kept in distilled water until they were to be treated with reagents. Before each reagent treatment, the specimen was carefully checked for cleanliness in the captive bubble apparatus. It was assumed that the surface was clean if, after fine grinding and washing of the specimen, the bubble would not stick. Specimens were handled with glass forceps, and precautions were taken to avoid contamination of the mineral surfaces. Contact angle measurements were carefully made several times on each treated specimen to obtain reliable average values. EFFECT OF pH VALUE AND SODIUM SULFIDE CONCENTRATION In each experiment, a specimen with a freshly ground surface was immersed for 10 min in a solution of sodium sulfide, washed and immersed for 15 min in a solution containing 30 mg per 1 of potassium amyl xanthate. The specimen was then washed again in distilled water and tested for contact angle in the captive bubble apparatus while submerged in distilled water. In this series of experiments, the pH of the sulfidizing solution was varied from 3 to 7, and the concentration of sodium sulfide, containing 60% Na2S, was varied from 50 to 650 mg per 1. Many combinations of pH value and sulfide concentration resulted in no contact between the bubble and the surface, but over a limited range of conditions, contact angles varying from 24ºto 52ºwere obtained. The data in Fig. 1 show sulfidization conditions that lead to bubble contact and those that do not. The region of contact is surprisingly small, which may indicate why flotation of chrysocolla involving sulfidization has proven so difficult in practice. Several features of the system are illustrated in Fig. 1. In the region between pH values of 4 and 6 with sodium sulfide concentrations below about 350

Jan 1, 1963