Search Documents

By CLARENCE WM. POY

THE most common difficulty faced by an engineer or mine operator when opening a new property in a new field is the lack of roads and of cheap transportation. This one item often swings the balance of success or failure in starting a project. In Alaska, as elsewhere, such problems are more or less serious. In the boom days around the Valdez district, as well as in other parts of this territory, freighting was accom¬plished by dog teams or horses, or even by men that were willing to put their shoulders into harness, because there were virtually no roads. More important, there was only one time when supplies could be transported, and that was when there was suffi¬cient snow on the ground following a heavy wind. Then, and only then, could one depend on the snow to support horses and sleighs, and be sure that the gulleys, streams, and crevices in the glaciers were filled with snow to avoid pitfalls. These methods were used when one had no roads, no streams in the summer to float a barge, or even a trail for a pack train. If the snow was deep and soft, trans

Jan 1, 1935

By Gustav Egloff

AN unexpected and unprecedented demand for its products now challenges the petroleum industry. Between 1939 wand 1946, domestic oil demand increased nearly 45 per cent and in the first half of 1947 it was 10 per cent higher than in 1946. In 1939 the United States produced 1,264,962. 000 bbl of crude oil and indications are that about 1,860,000,000 bbl will be produced in 1947, a 47 per cent increase. Runs to stills are more than keeping pace with production. The crude capacity of 365 operating refineries is rated as 5,400.000 bbl daily and almost 100 per cent of this capacity was running crude oil in August 1947. The oil industry is cognizant of our need for a greater volume of petroleum products and is expending the huge stun of four billion dollars on exploration. production. transportation, refining. and marketing of petroleum. Of this amount about half will be spent on exploration and production. a billion on refining. and another billion on transportation and marketing facilities.

Jan 1, 1947

By J. D. Wheeler, H. W. Mathews

The increased activity in West Texas, which started in 1933, has continued through 1936 at a constantly accelerated rate. During 1936 there were 1442 wells completed in the area as compared with 700 in 1935 and 468 in 1934. Of these completions, 1313 were producers with a total 24-hr. potential in excess of 1,750,000 bbl. From among the 1442 wells, eight are considered to be discovery wells for new West Texas fields. New Fields Bennett.—The Bennett field, which added Yoakum County to the oil-producing counties of West Texas, was actually indicated as an oil-producing area during 1935, but the discovery well, Honolulu Oil Corporation, Ltd. and Cascade Petroleum Company's Bennett No. l, was not given a production test until April 1936. The discovery well made 15 bbl. per hour through 3/4-in. choke with a plugged-back total depth of 5264 ft. First oil in the hole was from 5088 to 5090 ft., which is several hundred feet below the top of Permian lime. Producing limits of the field are unknown, as the second test had not reached the pay at the close of the year. Henderson.—-To date indications are that the Henderson pool, in northern Winkler County, is the most prolific area opened during 1936. This field, which lies to the north of the old Hendrick pool, is producing from the same reef-type dolomitic lime producing in the older field. The Henderson field was opened by the completion of R. H. Henderson, J. B. Walton-Humble 1-A in April 1936 for a natural flow of 2306 bbl. per day through tubing. Total depth of the discovery well is 3049 ft. Later development has indicated the productive area to be a rather narrow zone running slightly west of north. Present area of from 1000 to 1500 acres has been proved for production. Keys and Emperor.—The Keys and Emperor pools in the belt of sand pools running across Winkler County appeared for the first time on State proration schedules during 1936. This report considers these pools as links in joining the belt of sand production across Winkler County, for

Jan 1, 1937

By Eugene McAuliffe

In the year 1581, the counselors of King Philip of Spain suggested to that monarch that a canal across the Isthmus of Darien would open the west coast of the South American continent to Spanish miners and explorers, enlarging and expanding the flow of precious metals then just beginning to trickle across the path cut by Spanish Conquistadors, from old Panama to Puerto Bello on the east coast. The King sent out a party of surveyors and explorers under the command of a young engineer, Savadaerro, who returned after two years, reporting upon a location for a canal which was virtually adopted by the French engineers employed by De Lesseps, who in 1877 commenced the work of constructing the Panama Canal-296 years after Sava- daerro's first survey was begun. The suggestion for an Isthmian canal, made to the king at a time when Spain was a proud, virile nation and when that country was contending with England in the fields of discovery and conquest, represents a measure of vision that has never failed to intrigue the imagination. That the young Spanish engineer recommended an undertaking so gigantic in conception that it took three and one-third centuries for its completion from the time it was first visioned matters little. In the day of Philip of Spain,

Jan 1, 1932

By W. G. Sinclair

THE North Texas district presented in this paper includes the counties of Archer, Baylor, Clay, Cooke, Foard, Hardeman, Jack, Knox, Montague, Wichita, Wilbarger and Young. It corresponds with the Texas Railroad Commission's district No. 9. Table I conforms with the nomenclature of pools as designated by the Commission. Most of the oil and gas produced in this region, generally referred to as the Red River uplift, comes from the Pennsylvanian strata. In recent years, however, increasing amounts are being developed in both the Mississippian and Ordovician.

Jan 1, 1946

[ ]

Jan 1, 1938

By J. L. Lehman, J. D. Sudbury, J. E. Landers, W. D. Greathouse

A full scale field experiment on cathodic protection of casing answers questions concerning (1) the proper criteria for determining current requirments, (2) the amount of protection provided by different currents, and (3) the transfer of current at the base of the surface pipe. Three dry holes in the Trico pool in Rooks County, Kans., were selected for cathodic protection tests. The three holes were in an area where casing failures opposite the Dakota water sand often accur in less than a year. Examination of the electric togs showed the wells to be similar to other wells in the field where casing in four of seven producing wells has failed. The three holes were cleaned out and cased with 75 joints of new 51/2-in. 14-tb J-55. Each joint was visually inspected and marked before it as run. The casing was bull plugged and floated in the hole 50 that the inside might remain dry and free of excessive attack. Also, if a leak occurred, a pressure increase could be observed on gawge at the surface. Extensive testing was done, including potential profiles, log current-potentid curves and electrode measurements from both surface and downhole connections. Based on these data, a current of 12 amps was applied to one well and 4 amps to mother. The third well was left to corrode. During the two-year period when the casing was in the ground, [he applied current was checked weekly, and reference electrode measurements were made about every two months. Three sets of casing potential profi1e.c were run. When the three strings were pulled, each joint was examined for type of scale formed, presence of sulfate-reducing bacteria, extent of corrosion nttnck and pit depth. Since the pipe was new when run, quantitative determination of the protection provided by current was possible. This is the first concrete field evidence to help resolve the many arguments about the proper method for selecting adequate current for cathodic protection of oilwell (-using. INTRODUCTION A casing string is run when a well is drilled. This pipe is supposed to protect this valuable "hole in the ground" for the life of the well. Often the casing does not last the life of the well; it is with these casing failures that this work is concerned. The cost of repairing a casing failure varies from field to field—from as much as a $30,000 per leak average in California to $5,000 per leak in Kansas. Additional costs other than actual repairs are also important. These include formation damage, lost production, etc. Casing damage caused by internal corrosion is important in some areas. Treatment normally consists of flushing inhibitor down the annulus, but further research is being done on control measures. The test described in this paper is concerned only with external corrosion. The problem of casing failure from external attack has appeared in several areas including western Kansas, California, Montana, Wyoming, Texas, Arkansas and Mississippi. Cathodic protection is currently being used in an attempt to control external corrosion. From reports in the NACE there are thousands of wells currently under cathodic protection. The quantity of current being applied ranges from 27 amps on some deep California wells to a few tenths of an amp being supplied from magnesium anodes on wells in Texas and Kansas. Considerable field and laboratory effort1,9,5,6 was exented on the problem of cathodic prctection of casing, and it became fairly obvious that this method could be used to protect wells. Early workers showed that current applied to a well distributed itself over the length of the casing and was not concentrated on the upper few hundred feet. Basic cathodic protection theory had shown that corrosion attack could be stopped by applying sufficient current. The problem resolved itself, then, into one of trying to decide just how much current was necessary. Various criteria were utilized in installing the many existing cathodic protection installations. These methods included the following. 1. Applying sufficient current to remove the anodic slope as shown by the potential profile." 7. Applying enough current to maintain all areas of the casing at a pipe-to-soil potential of .85 v.' 3. Applying the current indicated by a log current-potential (or E log I) curve." 4. Supplying the current necessary to shift the pipe to-soil potential .3 v." 5. Applying 2 or 3 milliamps of current per sq ft of casing."

By G. A. Koenig, Moritz Stockder

Locality and Geological Occurrence. The Alpine region of Southwest Colorado, comprising the San Juan and Uncompaghre Mountains, is composed of a deeply eroded sheet of acid eruptive rocks, overlying in part gneissic sehists, and in part limestones and sandstones, including portions of the Silurian, Devonian, and Carboniferous systems. The section is clearly and beautifully exposed along the Uncompaghre River from its headwaters to its exit from the mountains. The river's course from the town of Ouray towards the Los Pinos agency is due north, and four miles from Ouray, in this direction, the Uncompaghre receives from the east the Red Cafion Creek. Following up the narrow caftan we find the section through white.. sandstone in strata dipping to the north and west, and belonging either to the lower or middle Devonian system. Presently the steep cafion-liko character of the ravine gives place to more gentle slopes, and we have entered crystalline rock-porphyry. The contact is well marked, for the sandstone, to a depth of from six to ten feet, resembles quartzite, i. e., is semifused. Ascending still higher, a small

Jan 1, 1881

By B. L. Landrum, J. Simmons, J. M. Pinson, P. B. Crawford

Patentiometric model data have been obtained to estimate the effect of vertical fractures on the areas swept after breakthrough in water flooding and miscible displacement programs such as gas cycling where the mobility is near one, The data are presented for the case of the fire-spot pattern in which the cemer well is fractured various lengths and orientations, the data indicate that for 10-acre spacing, fractures extetidirrg over 1300 ft in either directior1 from the fractured well may re.srrlt in reductions in sweep efficiencics from 72 to approximately 34 per cent. However. the area swept after break through may be quite largr and only 10 or 12 per cent 1ess than would be obtained if the reservoir were trot fractured. For the specific case when the volume of fluid injected is equivalent to 100 per cent of the pattern vol-unie, the swent area may vary from 80 to 88 per cent, depending on the lenght of the fracture. The former value is that which occurs when the break through or sweep efficiency was orrly 34 per cent and the latter figrrre of 88 per cent is that which is obtained if the reservoir were unfrac-ttm'd. It is pointed out that although the sweep efficiency may he very low in vertically fractured five-spot patterrz.s, the area swept at low water-oil ratios may be only 5 to 10 per cent less than those achieved if the reservoir were unfractured. INTRODUCTION Since the initiation of commercial reservoir fracturing techniques it has been desirable to determine the effect of fractures on the areas swept after breakthrough. Most water flooding or gas cycling projects are continued for substantial periods after the brcakthrough of the injected fluid. Although the sweep efficiency serves as one criterion for rating various flooding patterns. the area swept after breakthrough for various water-oil ratios or percentage wet gas, if cycling. is of perhaps more importance than the sweep efficiency alone. Sweep efficiency data on the vertically fractured five-spot have been presented3. Previous work on the line-drive pattern has shown the effect of vertical fractures on the area swept after breakthrough for the case in which the distance between injection and producing wells divided by the distance between adjacent input wells was equivalent to 1.5 (see lief. 2). The data indicated that for the line-drive pattern it may be desirable to flood or cycle substantially perpendicular to the fractures in order to achieve the greatest recovery for the smallest volume of fluid injected. For this study the center well of a five-spot is assumed as the fractured well. All fractures were assumed to originate at this well and extend into the reservoir for various distances and orientations. All the fractures are straight and are of large permeability compared to the matrix proper. These data are presented to aid the engineer in estimating fractured five-spot pattern performance. ANALOGY The potentiometric model was used in making this study. The model used was 20 20 in. by approximately 1-in. deep. For certain portions of the study one corner of this model was considered to be an injection well and the opposite corner a production well. To simulate vertical fractures a copper sheet was soldered to the wire well and made to conform to the desired length and orientation. In other studies the same model was used except that the four corners of the model might be considered as the corner wells of a five-spot pattern and a fifth well was placed in the center of the model. The well placed in the center of the model was fractured. The total fracture length is L and the well spacing. d. The complimentary fracture angles will be obvious from Figs. 3 and 4. The data obtained on the potentio-metric model assumes the pay to be uniform and homogeneous, the mobility ratio is one, steady-state conditions exist and gravity effects arc neglected. The permeability of the fractures is very great compared to that of the matrix proper. The po-tentiometric model has been used widely both in water flooding and gas cycling projects, and may be used for miscible displacement; how-ever. it is believed that the poten-tiometric model data are more properly applicable to gas cycling than water flooding because the model as-

By Jan M. Mutmansky

A knowledge of rock characteristics forms the foundation for the application of rock mechanics to engineering works. Hence, there has been an increased interest in the determination and proper utilization of rock properties data. Most numerical values quoted for rock properties are obtained from arbitrary tests and are not necessarily indicative of any intrinsic rock characteristics. Recent attempts to correlate these properties by statistical methods have attracted considerable attention, in the hope that these might give some clue to the fundamental properties. To date, correlation and regression techniques have been employed for this purpose. The use of statistics has also been deemed appropriate because of inhomogeneity and anisotropy in rocks. The problems have been further compounded by the lack of standardized methods of measuring rock properties. The various ASTM committees are still deliberating on these matters, but recommendations should be forthcoming in the near future. As more reliable data become available, the ability of geoscientists to find more meaningful relationships between rock properties will be greatly enhanced. The objective of this paper is to outline another statistical technique which might be useful in providing an insight into the relationships that exist between rock properties. This method does not attempt to predict rock characteristics, but rather compares the similarity or dissimilarity between properties. This enables rock properties to be classified into groups with similar intrinsic characteristics. The technique described is one form of factor analysis. It allows the results obtained to be depicted geometrically, so as to make ready visual examination possible.

Jan 1, 1968

SUDBURY ore processed by International Nickel Co. of Canada Ltd. was recovered for many years as two mill concentrates, one primarily of copper, and the other mixed pentlandite-pyrrhotite, But, Since iron content of the nickeliferous pyrrhotite concentrate was ten times its nickel value, capacity of smelting was limited by the need for slagging the excess iron. A process for recovering the iron con- tent was developed after some years of research and a $20-million plant was constructed to employ the new method. Built near Copper Cliff, Ont., the plant started operation early in 1956, scheduled for separate treatment of 365,000 tons of pyrrhotite each year. It is only the first unit of an installation which will have a capacity of more than 1 million tons per year of pyrrhotite. By early 1958, production totaled more than 200,000 long tons of 68 pct Fe pellets containing 0.003 pct P, 1.5 pct SiO2, 0.01 pct S, and 0.15 pct Ni.

Jan 8, 1958

By SIDNEY ROLLE

ACURSORY glance through the literature on the subject reveals that the ablest minds in the land are devoting themselves to the great question of labor, of which employment is one of the fundamentals. Volumes have been written and the end is not in sight. Employment management is today about in the position that efficiency was 15 years ago. During the early days of the war, and perhaps for a year or so before, labor was plentiful. As the war progressed and Europe drew on us for munitions, employers began to compete with one another for', all, classes of labor. Labor was difficult to obtain, wages rose, the labor turnover increased, and employers began to install employment departments, welfare plans, and all sorts of schemes, but the labor efficiency dropped. As the war progressed, greater and greater production was demanded. New factors were introduced each day. The government, labor unions, industrial councils, all tended, it seemed, to make the situation almost intolerable. Wages rose to fantastic heights, the cost of living rose higher and higher, and the efficiency dropped still further.

Jan 1, 1921

By W. M. Robertson

The rate of crack Propagation thvough a solid meta1 in the presence of a liquid metal has been calculated. The crack is assumed to propagate by solution of the solid in the liquid under the influence of an applied stress, with volume diffusion of the dissolved solute through the liquid controlling the propagation. The calculated velocities can be tens of centimeters per second or higher. THE embrittlement of normally ductile solid metals by liquid metals has been the subject of extensive study, as summarized in the book by Rostoker, McCaughey, and arkuus.' In experimental studies of liquid-metal embrittlement it is usually concluded that the observed crack-propagation rates are too high to be accounted for by diffusion processes. Diffusion is considered to be an unimportant factor and various other mechanisms are invoked to account for the experimental observations. The similarities of liquid-metal embrittlement to stress-corrosion cracking, to hydrogen embrittlement of steel, and to low-temperature embrittlement of bcc metals are frequently used as analogies for these mechanisms.1"3 The present paper assesses how rapidly a crack could propagate by a mechanism of volume diffusion through the liquid metal. We assume that the crack propagates by solution of the solid in the liquid at the crack tip under the influence of the applied stress and diffusion of the dissolved solute away from the crack tip. The model uses only macroscopic thermodynamic, kinetic, and elastic concepts. The calculations indicate that this dissolution-diffusion mechanism can give high crack velocities. In some previous treatments4'' of crack propagation in a liquid-metal environment the fundamental step has been the breaking of atomic bonds at the crack tip. The liquid greatly decreases the energy necessary to break these bonds. The present model assumes the crack is filled with liquid metal; the presence of the liquid is essential because diffusion through the liquid is assumed to control the rate of propagation. With proper modification this model could also apply to stress corrosion in a liquid environment. THEORY Consider a crack in a homogeneous elastic continuum, ignoring all the structural details of the solid. This neglects a host of metallurgical details which can be significant in the problem of liquid-metal embrittlement;' but this simple assumption is a useful approach in evaluating the role of diffusion through the liquid. The stress distribution around the crack tip establishes a gradient in the chemical potential at the tip, which causes a diffusion flux through the liquid away from the tip. The solid-liquid interfacial tension works against crack propagation, since propagation requires creation of interfacial area. From these two considerations we derive the diffusion flux, which then yields an expression for the velocity of the crack tip. The concentration of the solute in the liquid, C, is equal to the equilibrium concentration in the presence of an unstressed, flat surface, Co, plus the excess concentration due to the stress, AC(a), plus the excess concentration due to capillarity, AC(y): We calculate AC(o) and AC(y) and then obtain the diffusion flux. Consider (Fig. 1) a long flat crack of length 2L, thickness 2r, and tip radius r, where r remains constant as the crack propagates in the positive x direction. There is no stress ay in the y direction across the flat surfaces of the crack. The magnitude of the stress at the crack tip due to the applied stress, a,, is given by the relation6 ^=^[l-2^] 12] which, for long narrow cracks, becomes The stress increases the chemical potential in proportion to the strain energy.? The excess chemical potential due to the stress, Ap(a), is given by where 52 is the atomic volume of the solid and E the Young's modulus. Inserting Eq. [3] gives Now consider the crack to be filled with a liquid metal. The excess solubility due to stress, hC(a), is given by the excess chemical potential due to capillarity, Ap(y), is given by8 where y is the solid-liquid interfacial energy, and v1 and YZ are the two principal radii of curvature of any surface point. At the crack tip, r1 = -r and vz = m, so TRANSACTIONS OF THE METALLURGICAL SOCIETY OF AIME

Jan 1, 1967

By P. R. Sperry, A. P. Beck

It has been shown1 that in poly-crystalline strips of high purity aluminum with a fairly random orientation distribution, grain growth progresses gradually until the average grain diameter reaches a value approximately equal to the strip thickness. Recent work at this laboratory led to the realization that grain growth might be impeded to a considerable extent in the presence of a sharply defined texture, where orientation differences between neighboring grains are small. In order to investigate this effect the following experiment was carried out with the same lot of high purity aluminum previously used for grain growth studies in randomly oriented material.' Very large grain size was developed by grain growth at 650°C in specimens of 0.200 in. thickness. These specimens were then rolled to a thickness of 0.050 in. or 1.25 mm—a reduction of 75 pct. In the rolled strip each large grain corresponded to an elongated area easily identified by etching. After annealing for 1 to 25 min at 600°C and re-etching, these elongated areas were again recognizable. Within each area, corresponding to a single large grain before annealing, there formed by recrystallization a multitude of new grains with a fairly well developed preferred orientation. The orientation and the size of the new grains formed in areas corresponding to different large grains, varied widely depending on the orientation of the parent grains with respect to the rolling direction and the plane of rolling. Many areas were found where the average grain size was considerably smaller than the specimen thickness. Such an area occurred in a specimen cut in half before annealing. One half, containing a portion of the area in question, was annealed 1 min at 600°C, the other half, with the remaining portion of this area, for 25 min at the same tempera-Aluminum killed low carbon steel, § which is now used extensively for severe deep drawing or other difficult forming operations, is unusual in that its grain structure, after cold reduction and box annealing in accordance with conventional continuous sheet or strip mill practice, often is elongated, although at times it is equiaxed. Since this unusual structure has been found superior for many, but not all, severe forming operations, recrystallization of the steel, both at constant temperature and on continuous heating, was investigated and compared with that of rimmed steel in the hope that something might be learned about the mechanism of, and the factors controlling, the formation of such elongated grains. In this structure, the grains are elongated both in the lengthwise direction of the strip and transverse to this direction, even though nearly all of the extension in both hot and cold rolling is in the lengthwise direction. The grains are thus roughly pancake-shaped, being longer and wider than they are thick, as observed also by Burns and McCabe,1 and as illustrated by the typical structures shown in Fig 1. Fig la, representing a conventional longitudinal section, shows the length and thickness of the grains, whereas Fig Ib shows their length and width as seen by examining a section parallel to the sheet surface. Both illustrate the very irregular grain boundaries usually associated with the elongated grain shape. A finer equiaxed grain structure in this same grade is shown in Fig Ic. Either the elongated or the equiaxed structure may be present in the annealed product, and in rare instances the two types may coexist in a single specimen, as shown in Fig 1 d. Isothermal Recrystalliza-tion of Rimmed and Alamimum Killed Steel An aluminum killed steel known to have an elongated grain structure after conventional processing (Steel B, Table l), was selected for the initial recrystallization studies; for comparison, a rimmed steel, A in Table 1, was used. Samples of each in the form of hot rolled strip 0.075 and 0.095 in. thick, respectively, were cold rolled on a small laboratory mill in steps of about 0.010 in. per pass to obtain total reductions of 40 and 60 pct. Small pieces of the cold reduced strip were heated in lead at selected constant temperatures for one of several periods of time, then cooled in air. Rate of heating in the lead was, of course, very fast. Hardness of the cooled specimen was measured and a longitudinal section examined metallographically. Isothermal recrystallization curves for these two steels at 1050°F, based on hardness of the air cooled specimens, are shown in Fig 2 in which the amount of recrystallization corresponding to each plotted point is indicated. The marked difference in the behavior of these two types of steel is evident. After a corresponding amount of cold reduction, the rimmed steel recrys-tallizes in a much shorter time than the killed steel and the shape of its recrystallization curve, (plotted on a logarithmic time scale), is very different. The curve for rimmed steel indicates that recrystallization is analogous to isothermal transformation of aus-i.enite in that it proceeds at a progressively faster rate up to some 50 pct recrystallization, then at an increasingly slower rate. For the aluminum killed steel, however, the start of

Jan 1, 1950

By P. F. Gnirk

Consideration is given to creater formation with shallow, contained, chemical explosions in rock masses which exhibit different inherent physical and mechanical properties as determined by standard laboratory techniques. The primary purpose is to determine whether or not a simple but useful generalized correlation can be established between explosive crater formation and one or more common rock properties. Such a correlation could be beneficial in predicting with some degree of reliability the size of a crater which could be expected in a particular rock type for a given input of explosive energy. A series of crater formation experiments employing constant weight charges of Gelex 2 explosive was conducted in five submembers of the taconite formation at the eastern end of the Mesabi Range in northeastern Minnesota. Five mechanical and physical properties-unconfined tensile and compressive strengths, Young's modulus of elasticity, longitudinal wave velocity, and density-were determined by conventional laboratory techniques using core samples from the taconite submembers. Although insufficient data were obtained to warrant the use of mathematical methods in the determination of empirical relationships, the results provided a fairly strong indication that with an increase in magnitude of any one of the five rock properties definite decreases in the optimum crater volume and surface area occur. Furthermore, for a constant explosive energy input, the presence of bedding planes and joint systems in a rock mass influences the formation of craters in such a manner as to increase the volume of rock broken substantially above that expected from the same rock mass without joint systems and, in particular, without bedding planes.

Jan 1, 1968

By Lo-Ching Chang, K. M. Goldman

The kinetics and mechanism of transfer of a constituent across a slag-metal interface are fundamentally important because many metallurgical processes involve the existence of a slag phase and a metal phase. Industrial processes seldom proceed to equilibrium, and information of the rates and modes of reactions are therefore often of greater practical importance than equilibrium data. A study of the kinetics of sulphur transfer across a slag-metal interface under reducing conditions will contribute a great deal toward a better understanding of desulphurization in the blast furnace process. The general principles existing in the transfer of a constituent, such as sulphur, across a slag-metal interface can be extended to similar transfer phenomena in other metallurgical processes. The present paper will demonstrate how such studies will lead to fruitful results from both the practical and theoretical standpoints. EXPERIMENTAL METHOD The apparatus used was, simple. A graphite crucible 15/8-in. id, a wall 1/8-in. thick, and a depth of 4 in., was packed in an outer fused silica tube with powdered magnesia. The crucible assembly was rotated at a speed of 235 rpm inside an in- duction coil. A charge of 250 g of Armco ingot iron was introduced into the graphite crucible and melted by induction heating. The melt was held at a desired temperature for 3-5 "'in., aftcr which 7.5 g of granular ferrous sulphide was added and the bath was held for another 3-5 mi11. A metal sample was then taken by means of a fused silica tube and a rubber suction bulb. Immediately after the metal sample was taken, 30 g of a prefused and crushed slag were introduced. The slag reached the ternperature of the furnace in 1 to 1 1/2 min. Slag

Jan 1, 1949

By K. M. Goldman, Lo-Ching Chang

The kinetics and mechanism of transfer of a constituent across a slag-metal interface are fundamentally important because many metallurgical processes involve the existence of a slag phase and a metal phase. Industrial processes seldom proceed to equilibrium, and information of the rates and modes of reactions are therefore often of greater practical importance than equilibrium data. A study of the kinetics of sulphur transfer across a slag-metal interface under reducing conditions will contribute a great deal toward a better understanding of desulphurization in the blast furnace process. The general principles existing in the transfer of a constituent, such as sulphur, across a slag-metal interface can be extended to similar transfer phenomena in other metallurgical processes. The present paper will demonstrate how such studies will lead to fruitful results from both the practical and theoretical standpoints. EXPERIMENTAL METHOD The apparatus used was, simple. A graphite crucible 15/8-in. id, a wall 1/8-in. thick, and a depth of 4 in., was packed in an outer fused silica tube with powdered magnesia. The crucible assembly was rotated at a speed of 235 rpm inside an in- duction coil. A charge of 250 g of Armco ingot iron was introduced into the graphite crucible and melted by induction heating. The melt was held at a desired temperature for 3-5 "'in., aftcr which 7.5 g of granular ferrous sulphide was added and the bath was held for another 3-5 mi11. A metal sample was then taken by means of a fused silica tube and a rubber suction bulb. Immediately after the metal sample was taken, 30 g of a prefused and crushed slag were introduced. The slag reached the ternperature of the furnace in 1 to 1 1/2 min. Slag

Jan 1, 1949

By GUY C. RIDDELL

THE recent purchase by an American investment trust of a substantial block of shares in a British owned Venezuelan copper operation directs attention to mining activities that have been quietly gaining momentum in that country for a number of years. We hear so much of oil work in Venezuela that attention to its metal-mining activities is in most quarters casual. In gold and copper the country has made some interesting mining records, and two of the old districts are ,digging in for a come-back. Copper Copper production centers in the state of Yaracuy. The Aroa-Cumaragua mining region has had a long and eventful history. The Aroa mine itself, 50 miles from the coast in West-Central Venezuela, was discovered in 1605. First mined in 1632, owned at one time by Simon Bolivar, it has been reopened many times and is now , the basis of substantial operations by the South American Copper Syndicate, Ltd. of London. The latter has operated the property profitably, off and on, for a number of years, paying heavy dividends on a small investment-at times over 300 per cent annually.

Jan 1, 1929

By Henry M. Howe

The striking features of American Bessemer practice aré its large output and its low initial silicon and initial temperature. These are interdependent. Large outputs implies short blows and short intervals between blows. Short blows imply low silicon and fast blowing. Low silicon implies short intervals and fast blowing. Our blows are short because we have little silicon to remove, and because we remove it fast by supplying blast rapidly. We get enough heat even with little silicon, because our blows and the intervals between them are so short that relatively little heat escapes from our vessels. Were we to lengthen our intervals, or to blow more slowly, we would have to meet the increased loss of heat from our vessels, either by using more silicon, or by melting hotter, i.e., by burning more coke, in the blast-furnace or in the cupola. Finally, our short intervals imply powerful machinery, efficient organization, and extreme specialization and subdivision of labor, which can be profitable only when the output is large. Let, us now take these points up in more detail, first glancing at some examples of our large outputs, given in Table I., and of the composition of our iron. Output.—On presenting such results to some foreign metallurgists, I have been told, " Oh yes, we quite understand that. You really turn out no more steel than we do. As a matter of personal pride, your manager gets up a tremendous spurt for a day, or even a week, crowds on men wastefully, rushes through great quantities of metal, and then for months afterwards has to recuperate. The machinery has been strained ; the owner's money has been wasted ; the men have been prostrated—all to gratify the manager's vanity. Your average output is no larger than ours." Personal pride has, doubtless, played its part; without it we would still be savages, or apes, or mollusks, if you prefer. These baser motives are the mudsills of progress, the soiled roots of that growth of which civilization is the flower. Great outputs were made

Jan 1, 1891

By FLOYD T. TAYLOR

IN 1833, less than one hundred years ago, Michael Faraday discovered and stated the laws of electrolysis. His discovery formed the foundation of a new use of metals which has now reached a variety of application not ordinarily appreciated. Furthermore, things can be done with electro-deposited coatings which have thus far defied other methods. Some of the uses of electro-deposited coatings are interesting. The tonnage of metals already finding an outlet through such a channel is considerable. In general electro-deposits have two characteristics: ornament plus utility; utility plus ornament. Both these factors are usually found associated in electro- deposits. Ornament plus utility was probably the first use. For example, the silver-plating of tableware, having its real birth in Birmingham, England, about 1844. However, this same ornament plus utility retarded the development of electro-plating, because in the beginning, electro-plated articles were branded with the odium of imitation and shunned accordingly. The gold brick of the swindler may be an exception to this statement.

Jan 1, 1929