Search Documents

President Howe: It is, of course, not easy to discuss off-hand the paper which Mr. Becker has presented with so much lucidity. I will only make one remark, which is outside of the line of his argument, and concerns merely a passing allusion in his paper. Mr. Becker speaks of the fact that glass breaks with a flat or conchoidal fracture, and that steel shows a rough or " cupped " surface of frac-

Jan 1, 1895

By Henry S. Burnholz, Charles Y. Clayton, Francis B. Foley

This work was first undertaken for the U. S. Bureau of Mines, in 1919-20, by C. E. Julihn, superintendent of the station at Minneapolis. Learning of the interest, in this subject, of B. F. Tillson, of the New Jersey Zinc Co., Mr. Julihn and Mr. Foley went to Franklin, N. J., and discussed the matter with him. A conference in Chicago, in November, 1920, was attended by Dr. F. G. Cottrell, who was then Director of the Bureau of Mines, and representatives of the Bureau of Mines and of the hlissouri School of Mines and Metallurgy; at this time a cooperative plan of work was agreed upon by the Bureau of Mines and the Missouri School of Mines. In February, 1921, Mr. 'Tillson arranged a conference on this subject at the time of the annual meeting of the American Institute of Mining and Metallurgical Engineers, at which several technical papers were presented. In a paper, the Breakage and Heat Treatment of Hock Drill Stcels, he suggested a program that might be carried out in connection with the investigation of the problem. At this conference Mr. Manning, former Director of the Bureau of Mines, suggested the formation of an advisory committee to the Bureaus of Mines and of Standards for prosecution of this investigation. On Feb. 20, 1922, a secoud conference in New York, at the time of the annual meeting of the American Institute of mlining and Metallurgical Engineers, was attended by representatives of various technical societies. At this meeting, the report of Nov. 20, 1921, of the Chiefs of Divisions of Metallurgy of the Bureaus of Mines and of Standards, was discussed and it was agreed: 1. That the survey recommended by the two bureaus should be undertaken, which survey would have for its object the ascertaining of the present status of the practice of the heat treatment of drill steels, the extent to which the breakage occurs, etc.; and 2. That a report should be presented, of the findings of those who made the survey, to the Advisory Board to the Bureaus of Mines and of Standards. The Bureau of Standards assigned $4000 to the prosecution 01 a three-months' survey, which was carried out in April, May, and June, 1922, of about sixty mines

Jan 1, 1923

By Charles Y. Clayton, Henry S. Burnholz, Francis B. Foley

This work was first undertaken for the U. S. Bureau of Mines, in 1919-20, by C. E. Julihn, superintendent of the station at Minneapolis. Learning of the interest, in this subject, of B. F. Tillson, of the New Jersey Zinc Co., Mr. Julihn and Mr. Foley went to Franklin, N. J., and discussed the matter with him. A conference in Chicago, in November, 1920, was attended by Dr. F. G. Cottrell, who was then Director of the Bureau of Mines, and representatives of the Bureau of Mines and of the hlissouri School of Mines and Metallurgy; at this time a cooperative plan of work was agreed upon by the Bureau of Mines and the Missouri School of Mines. In February, 1921, Mr. 'Tillson arranged a conference on this subject at the time of the annual meeting of the American Institute of Mining and Metallurgical Engineers, at which several technical papers were presented. In a paper, the Breakage and Heat Treatment of Hock Drill Stcels, he suggested a program that might be carried out in connection with the investigation of the problem. At this conference Mr. Manning, former Director of the Bureau of Mines, suggested the formation of an advisory committee to the Bureaus of Mines and of Standards for prosecution of this investigation. On Feb. 20, 1922, a secoud conference in New York, at the time of the annual meeting of the American Institute of mlining and Metallurgical Engineers, was attended by representatives of various technical societies. At this meeting, the report of Nov. 20, 1921, of the Chiefs of Divisions of Metallurgy of the Bureaus of Mines and of Standards, was discussed and it was agreed: 1. That the survey recommended by the two bureaus should be undertaken, which survey would have for its object the ascertaining of the present status of the practice of the heat treatment of drill steels, the extent to which the breakage occurs, etc.; and 2. That a report should be presented, of the findings of those who made the survey, to the Advisory Board to the Bureaus of Mines and of Standards. The Bureau of Standards assigned $4000 to the prosecution 01 a three-months' survey, which was carried out in April, May, and June, 1922, of about sixty mines

Jan 1, 1923

By AIME AIME

FREDERICK WORTHEN BRADLEY, the newly elected president of the Institute, may be said to be the prototype of the men who have built up the great mining industry of the West. He was born in Nevada County, Cal., on Feb. 21, 1863, and studied mining at the University of California from 1882 to 1884, as a member of the Class of 1885. He was in contact with the mining industry from his earliest years and in his reminiscences which we published last month, he told of meeting Thomas Mein and H. C. Perkins in 1877. Beginning as assayer and roustabout at the Eagle Bird mine, in Nevada county, Mr. Bradley was a deputy mineral surveyor in 1886 and 1887 and superintendent of the Spanish mine from 1885 to 1890. There he made a record of mining gold ore at 65 cents per ton that was not only astounding in that day when modern large scale mining had not yet been developed but is still a mark to shoot at. As a result he was called in 1890 to be assistant manager of the Bunker Hill and Sullivan and was made manager in 1893. In 1897, he was elected to the presidency of the company, a position he still holds. H. C. Perkins and D. O. Mills, the largest stockholders in the Bunker Hill and Sullivan Co. took over the Tacoma smelter in 1898, feeding it with concentrate from the Coeur d'Alene and Douglas Island mines but also doing a gen-era1 smelting business. Mr. Bradley was put in as president of the Smelting company, and held that position until the plant was sold to the American Smelting Securities Co. in 1905.

Jan 1, 1929

By Willis H. Carrier

PARTICULAR interest in the ventilation of deep mines, especially those in South Africa, has been created by a very complete system of cooling of the world's deepest mine, the Turf shaft of the Robinson Deep in Johannesburg. The writer visited this mine in January, 1936, and again in 1937. During these visits and subsequently, a considerable part of the theory involved in rock cooling in tunnels was developed and this has been checked by practical observations of the rates of rock cooling made within mines. The purpose of this paper is to set forth the method of attack of the mine problem. The cooling or air conditioning of mines by the use of mechanical refrigeration was not wholly new 1-5 when the Robinson Deep installation was made. The first mine to be cooled was the Morro Velho mine, in Brazil. The first installation in this mine was put into operation in December 1920, the refrigerant being ammonia.5 The surface cooling gave considerable benefit but it proved inadequate as greater depths were reached, therefore in 1929 two centrifugal refrigerating machines were installed at the 6000-ft. level. These were used in conjunction with the surface cooling system to furnish additional cooling at the lower levels. This later installation used Carrene as a refrigerant. This nonflammable refrigerant, having a boiling point of 104º at sea level, insured reasonable safety, since all parts of the machine operated at subatmospheric pressure. Very favorable reports have been received on the effectiveness of this installation, but no recent data are available. An interesting feature of that plant is that the condenser water is cooled by spraying it into the exhaust air from the mine at the base of the ventilation upcast, which permits the water to be cooled within a few degrees of the wet-bulb temperature of the air entering the upcast, and the only water that has to be supplied for condensing purposes is that lost by evaporation, or about 0.5 per cent of the volume circulating through the condenser. This plan affords an ideal means for the removal of the heat load from the refrigerating system, and of course also from the mine itself. In many mines, however, especially those in South Africa, there is no

Jan 1, 1938

By W. J. Taylor

In making heating gas with anthracite coal for roasting ore during the past few years, I have tried many forms of gas generators. So far, the most successful and satisfactory one has been what we call a fluxing producer, which is simply a small cupola or blast furnace, in which we charge with the coal, say, 30 or 40 per cent. of basic blast-furnace cinder, to unite, when melted, with the ash or earthy matter in the coal, and carry it off as cinder. The producer we have in use at Chester, N. J., has more of the lines of a blast furnace than a cupola, the hearth being 24 inches diameter and 24 inches high. It then enlarges on an angle of about 25 degrees from a perpendicular to 4 feet, and then is drawn into 3 feet on top ; total height, 12 feet. We use one water coil-tuyere 12 inches above the bottom, and blow through a 1 1/2 - inch nozzle. The depth of coal above the tuyere averages about 6 feet. The producer-is blown with

Jan 1, 1881

The nickel suppliers are hard at work across the entire spectrum of the industry-from exploration and mining on the one hand to the development of new applications of this unique metal on the other. The reason-a surging demand for nickel by the free world. Evidence of interest and activity in nickel abounds. Companies such as Anaconda, American Metal Climax, Kaiser Aluminum & Chemical, Patino, Newmont-firms that have not been in the nickel industry before-are now involved in various exploration and development ventures around the world. International Nickel, Falconbridge, Le Nickel and Sherritt Gordon-the big names in the industry -have committed vast sums of money and talent in a variety of new developments designed to ensure their status as leading producers of this commodity. As a result, the world is now seeing a rapid build- up in nickel capacity, and in this issue of [ ], the editors have prepared a summary of these fast- moving major developments.

Jan 10, 1968

By B. W. Prof. Frazier

(Read at the Wilkes-Barre Meeting, May, 1877.) THIS interesting application of the laws of thermodynamics to metallurgical practice has not been discussed by any writer, within my reading, except the late Prof. Gallon of Paris. In his Cours de Machines,* Prof. Callon has given a short but lucid discussion of this subject in the admirably clear style for which he was remarkable. Although the interest attached to the subject is rather theoretical than practical, I have thought that an attempt to explain the mechanical action exerted in the hot-blast oven might not be entirely devoid of utility, especially in the suggestions which it involves. The statement, that the mechanical work performed in heating the blast is, when high temperatures are produced, considerably greater than the work performed by the blowing-engine, may seem incredible to many who are practically acquainted with the subject, appearing, as it does, to conflict with the results of their experience. It is, nevertheless, literally true, and I shall attempt in this paper to prove it, and to explain why it has not rendered itself palpably manifest in practice. Before proceeding to the mathematical demonstration, it will be well to recall to mind the definitions of some terms employed by writers in mechanics and thermodynamics. The actual energy of a moving body, as defined by Rankine, is the work which it is capable of performing against a retarding resistance before being brought to rest, and is equal to the energy which must be exerted on the body to bring it from a state of rest to its actual velocity. The value of that quantity is the product of the weight of the body into the height from which it must fall to acquire its actual velocity. * Vol. I, chap. x, [§ ] 4, p. 312.

Jan 1, 1878

By T. W. Guy

During the past three years the Surface Preparation Committee of the American Mining Congress Coal Operators' Committees has been collecting data on dewatering and drying washed coal, and on screening coal in representative plants in the Eastern and Central bituminous fields. Because of wide variations in bed moisture, such data can be compared only after deducting the bed moisture. It was found that practically every company used a different routine for moisture sampling and determinations. Some reported the moistures as total moistures, others as surface moistures, air-dried moistures, or oven-dried moistures. For most of the reports it was necessary to estimate, from a consideration of the bed moisture and other data available in a given case, corrections to be made in order to obtain surface-moisture figures as a common basis for comparison. At any plant, and regardless of bed moisture, the percentage of surface moisture remaining in a product when the dewatering, or a given stage of the dewatering, has been completed, is the real measure of what has been accomplished. The descriptions and data given with Fig. 1 show that surface-moisture figures show relationships that would not be shown by total moistures. Therefore bed moisture should be deducted, or, if more practicable, the surface moisture of the products should be measured direct. A preparation engineer finds one per cent, or even a part of one per cent, of surface moisture a very important consideration in the results of his efforts to find the most effective and economical methods of reducing and controlling the surface moisture in his products within the required limits. Therefore it is important for him to have accurate measurements of surface moisture with minimum uncertainty as to whether they sometimes include less than the surface moisture and at others all of the surface moisture plus an unknown part of the bed moisture. The Problem We know that pieces of coal have a capacity for holding water: (1) inside themselves, which is a natural characteristic of the bed from

Jan 1, 1938

By T. W. Guy

During the past three years the Surface Preparation Committee of the American Mining Congress Coal Operators' Committees has been collecting data on dewatering and drying washed coal, and on screening coal in representative plants in the Eastern and Central bituminous fields. Because of wide variations in bed moisture, such data can be compared only after deducting the bed moisture. It was found that practically every company used a different routine for moisture sampling and determinations. Some reported the moistures as total moistures, others as surface moistures, air-dried moistures, or oven-dried moistures. For most of the reports it was necessary to estimate, from a consideration of the bed moisture and other data available in a given case, corrections to be made in order to obtain surface-moisture figures as a common basis for comparison. At any plant, and regardless of bed moisture, the percentage of surface moisture remaining in a product when the dewatering, or a given stage of the dewatering, has been completed, is the real measure of what has been accomplished. The descriptions and data given with Fig. 1 show that surface-moisture figures show relationships that would not be shown by total moistures. Therefore bed moisture should be deducted, or, if more practicable, the surface moisture of the products should be measured direct. A preparation engineer finds one per cent, or even a part of one per cent, of surface moisture a very important consideration in the results of his efforts to find the most effective and economical methods of reducing and controlling the surface moisture in his products within the required limits. Therefore it is important for him to have accurate measurements of surface moisture with minimum uncertainty as to whether they sometimes include less than the surface moisture and at others all of the surface moisture plus an unknown part of the bed moisture. The Problem We know that pieces of coal have a capacity for holding water: (1) inside themselves, which is a natural characteristic of the bed from

Jan 1, 1938

By Walter Knox, J. D. Doherty

IN 1939, at the request of The Koppers Coal Co., the Koppers Company Research Department established a Stoker Coal Research Laboratory for the purpose of investigating the performance characteristics of stoker coals in typical domestic stoker installations. Fig. I is a photograph of part of the laboratory. The material in this paper deals with the performance of one coal in a single installation. Presented are details of this installation, mechanical characteristics of the stoker, and the results of a series of burning tests in which adjustments were systematically varied. SUMMARY OF RESULTS Mechanical Features I. A large percentage of the total power consumed by a domestic stoker is used to operate the gear case and motor (Fig. 3). 2. The power consumption per ton goes down with an increase in rate of coal feed (Fig. 4). 3. The automatic air control in this stoker showed advantages over manual control (Fig. 5). 4. The air velocities through the retort tuyeres were uniform around the retort, but varied between the rows of tuyere rings (Fig. 6). 5. The crushing of coal with this stoker increased the minus 1/8-in. from 1 1.6 per cent to 19.2 per cent. There was a noticeable segregation of coal as it came from the retort and distribution was not uniform (Fig. 7). 6. Measurement of air entering over the fire showed that with some not uncommon adjustments this air may he a high percentage of the total air supply (Fig. 8 and Table I). Operating Performance I. The removal of clinker was shown to give a period of poor performance characterized by a high fuel-bed resistance and a high percentage of carbon monoxide in the flue gases (Fig. 10). 2. The fuel-bed resistance was found to decrease as the fuel bed built up in a normal response to heat demand after a prolonged hold-fire (Fig. II). 3. With intermittent operation the burning rate was almost always less than the feeding rate. The wide variations were found to be greatly dependent upon the length of the On period and the length of the intervals between On periods (Fig. 12). 4. The maintenance of a low furnace draft led to less fly ash, better clinker formation, and higher efficiencies (Fig. I3). 5. The maintenance of a minimum of excess air also resulted in less fly ash, better clinker formation, and higher efficiencies (Fig. 14). GUIDING PRINCIPLES In planning the investigations, the following principles were adopted: Selection of Healing Equipment.-Use only standard models of stokers and furnaces representative of those widely used.

Jan 1, 1942

By Thomas T., Read

IT is difficult to judge how much influence the success attained during its first year, 1864-65, by the School of Mines at Columbia had on developments in education for the mineral industry elsewhere in the immediately subsequent years. The facts are as follows: 1. The Massachusetts Institute of Technology began giving instruction in February 1865, with a mining course included in its curriculum. 2. Early in 1865 the faculty of the Department of Science, Literature and the Arts of the University of Michigan requested permission from the Regents to establish "a course of study to be called the School of Mines . . . Also that the degree of Mining Engineering, be conferred on students who should complete the course of study prescribed in the same." A resolution authorizing this was adopted by the Regents on March 28, 1865. 3. Samuel Hooper endowed a Sturgis-Hooper professorship of geology at Harvard in 1865 with the intention of making it a nucleus of a new School of Practical Mining and Geology. 4. Yale appointed Alfred P. Rockwell professor of mining in 1865. 5. Lafayette College appointed Henry S. Osborn professor of mining and metallurgy in 1865. 6. Washington College (as Washington and Lee was then known), rising out of the ashes of Civil War destruction, made a fresh start in 1865, with Generalized as its president, and offered a mining course in the first catalogue thereafter published. 7. Lehigh University, founded in 1866, had a mining curriculum from its beginning. 8. Rensselaer Polytechnic began offering a curriculum in mining and metallurgical engineering in 1867. It would be natural to suppose that these events were a reaction, to the success of the school at Columbia, - and possibly they

Jan 1, 1941

By H. E. Kramm

During the summer of 1910, I had the opportunity to study in detail the geological conditions of what is known in northern California as " Harrison gulch," in Shasta county. Though the district, as a whole, that is, the western part of Shasta and the eastern part of Trinity county, has contributed during the last 15 years a considerable share of the gold-production credited to Shasta county, very little is known of its geology, perhaps because the country is covered with a dense growth of brush which makes exploration and prospecting extremely difficult. Topographically the district presents a succession of ridges trending approximately N-S., and alternating with deep, narrow canyons. The drainage is partly into the Sacramento, partly into the Trinity river. Climatic conditions in summer time are almost ideal. It is true, the thermometer may climb to 115°, but the air is dry

Jan 1, 1913

By Edward O’Toole

THe Pocahontas district occupies the extreme southern end of West Virginia, principally McDowell, Mercer and Wyoming counties, and a part of Tazewell county, in southwestern Virginia. The first record of the coal field is a report by Prof. J. P. Lesley, of Pennsylvania, about 1880, in which he mentions a coal opening at the upper end of Abbs Valley, Tazewell county, Va. C. R. Boyd, a mining engineer of Wytheville, Va., published a series of articles in 1881, mentioning coal on Indian Creek, Tazewell county, and on Horse Pen creek, which coals, he stated, extended toward the Ohio River. He also mentions the Abbs Valley coal reported by Lesley. In 1881, F. J. Kimball (who became president of the Norfolk & Western R. R. in 1883)) after examining the Scott mine in Abbs Valley, went northward across Abbs Valley Mountain to the place now known as Pocahontas, where he located what has since been called No. 3 vein of Pocahontas coal. In November, 1882, Jed Hotchkiss and others prepared a cross-section of the Flat Top Mountain coal measures, some notes on which were published by Mr. Hotchkiss, between 1880 and 1892, under the title of " The Virginias.' In May, 1881, the Norfolk & Western R. R. was organized through the purchase of the Atlantic, Mississippi & Ohio R. R., an old line running from Norfolk, Va., to Bristol, Tenn., with branches from Petersburg to City Point and from Glade Springs to Saltville. At that time, charters had been granted for three railroads tributary to the New River Valley, but their proposed routes would indicate that the promoters were concerned with minerals, timber, and a connection with the Chesapeake & Ohio R. R., rather than the development of any coal in the Pocahontas district. One of them was projected to extend up Bluestone River a short distance, but not far enough to reach the coal in the Bluestone Valley, and a little grading was done for a narrow-gage road between New River Station and a point in Giles county, Virginia, near the West Virginia line. All charters and railroads in this district were acquired by the Norfolk & Western R.R.

Jan 1, 1925

By T. L. Joseph

IT is a distinct privilege to participate in this meeting convened to honor the memory of Henry Marion Howe, a distinguished scientist and metallurgist. Many have added to our rapidly growing fund of metallurgical knowledge but few have made the unique contribution of formulating basic concepts essential to an over-all comprehensive view of the subject of metallography. Of those previously selected to deliver this lecture, several have added a personal touch to their discourse because they were able to refer to their associations with Dr. Howe. It was not my good fortune to know him or to enjoy his inspiring influence. Like most of you, my contact has been with his published works, which are outstanding in that they provide lucid, detailed expositions of the nature and behavior of metals and alloys. His deep understanding and clarity of expression have greatly accelerated our progress in metallography and in the use of metals. The degree to which a man's thinking, experimentation and writing contribute toward an understanding of basic laws and phenomena determines whether his life's work is of transitory or permanent value. This occasion appropriately recognizes the fundamental importance of Dr. Howe's pioneer work in the field of metallurgy. On two former occasions, gray iron was selected as a subject for discussion. The fact that the production of pig iron has not been discussed before does not reflect any lack of interest on the part of Dr. Howe or former lecturers in the process that under- lies the production of steel. Although Dr. Howe's work in his later years centered around metallography, his earlier publications show a considerable interest in the production of iron and steel. He recognized that in the ascending spiral of metallurgical advancement we are not winding a single thread but are weaving a complex fabric. Specific evidence of his interest in the production of pig iron may be found in his book1 on The Metallography of Cast Iron and Steel. In explaining why blast furnaces have been in constant use for about 600 years, he says: "The process is economical because it utilizes with extraordinary completeness the calorific power of the coke due to the thorough transfer of heat from the gaseous products of combustion to the charge." This emphasis on heat transfer, overlooked in many more extended and more recent discussions of the blast-furnace process, illustrates Professor Howe's ability to see the essentials. Other distinct advantages of the blast furnace, such as the removal of much of the sulphur and practically all of the oxygen, were mentioned. It was also stated that although the blast- furnace process is complex in nature, its outward form is comparatively simple, thus permitting large-scale production at small labor costs. All who contemplate the production of metallic iron from its ores by any other process might well consider the

Jan 1, 1946

By Dewey J. Sabin

THE Rio de Canada Honda placer property is situated at an altitude of 5500 ft. above sea level in the San Luis Mountains of the Province of San Luis, Argentina. The mine is reached by 70 km. of fair truck road, from the nearest railway station on the Ferrocarril Buenos Aires al Pacifico. The Pan-American airport at Villa Mercedes, 1.40 km. distant, serves as the most convenient point for shipment of gold. Placer mining in the Rio de Canada Honda dates from the time of the Incas and the present native population depends on the gold washed from this river and the adjacent arroyos as a means of livelihood as did the many generations before them. They dig pits to bedrock where they are not driven out by water, and mine the bedrock gravel by means of tunnels and caves. No timber is available and the ground is supported by rock cribs carefully built with the boulders encountered; or with angular blocks of slate rock taken from quarries on the surface.

Jan 1, 1936

By B. M. Larsen

A discussion based on three commercial furnace tests and electrical analogue calculations is presented. It shows that while regenerator efficiency is mainly dependent on loading or relative amount of heat exchange surface plus the heat transfer coefficients as effected by flow velocity, the actual air preheat temperature can be high or low, largely independent of regenerator efficiency, mainly due to the diluting or unbalancing effects of cold air leakage into various parts of the furnace system. THERE are many signs of a renewal of interest in the heat regeneration aspect of the open hearth process, among them being the recent paper by Marsh,' the introduction of auxiliary checkers in the stacks of the Isley furnace design, and a number of recent installations of two-pass checkers in new and old furnaces. However, there are also signs of yielding to the usual temptation of oversimplifying a problem. Faced with the job of obtaining better draft on a furnace, for example, a good designer always recognizes that focusing attention on some one factor, such as height of the stack or capacity of the exhaust fan, does not make his problem any easier; rather he must look at the whole system, including such items as valve resistances, bends in the flues, and flow resistance in the waste heat boiler; then he must make his design in relation to the available draft so as to avoid any serious bottleneck in the system. Yet this example is really much simpler than the problem of air preheating, and again, the latter problem is not really made easier by concentrating on air temperature in uptakes and on the more obvious methods for making this air as hot as possible. Also to be considered are such things as the total amount of air needed theoretically for complete combustion at any selected fuel rate, together with that needed for oxygen absorbed into the bath and for burning the combustible gases given out from the bath, plus some excess air. Furthermore, how does this total air requirement relate to the regenerator efficiency at various loadings? How much of the total air equivalent in stack gases will come from preheated air passed through the whole length of the incoming regenerator and how much from air leakage into various zones of the whole furnace system? Does the effect of leakage air differ depending on whether it leaks into the ingoing regenerator, the furnace above floor level, the outgoing regenerator, or the stack zone? Over a number of years we have in this Laboratory experimented with methods for measuring hot gas temperatures; we have measured, approximately, the efficiency of a few regenerators on commercial furnaces and we have developed an electrical analogue' for calculations of regenerator efficiency. The whole problem is too complex to cover in one paper even with a more complete background of data than we possess, but we can attempt here to clarify certain aspects in a general way, hoping to assist specific plant studies on individual furnaces. Some of our earlier experience has been incorporated into chaps. 4, 19, 20, and 21 in the book "Basic Open Hearth Steelmaking,"" and on the assumption that this text is available to most readers, this discussion has been shortened by references to that book. The most recent design of a flowing-gas thermocouple which we are now using for measurement

Jan 1, 1955

By AIME AIME

THE ninth International Petroleum Exposition held at Tulsa, May 16-23, broke all size, sales, and attendance records of previous shows. More than $12,500,000 worth of equipment was on the grounds. There were 546 companies exhibiting and every available inch of the fifteen acres allotted to exhibit was taken. Drake Drive, the main street of the exposition, was literally "supply row" with National Supply, Frick-Reid, Continental Supply, Oil Well, Bridgeport, International Derrick and Equipment, and Parkersburg Rig and Reel companies occupying the entire space. The exhibitors were a cross section of American industry, with such firms, besides the strictly oil equipment firms, as the United States Steel Corp. and others allied to the oil industry, exhibiting. Between $10,000,000 and $15,000,000 of equipment is estimated to have been sold on the grounds during the exposition. Valuable contacts were made by the exhibitors with key oil men. Attendance passed the 175,000 mark for paid admissions in contrast with 154,000 for the eighth exposition in 1934. Visitors registered from Venezuela, Soviet Russia, India, Germany, Spain, Mexico, England, Canada, France, Colombia, Greece, West Indies, and Rumania. Hotels were overflowed and a housing bureau found rooms in private homes for thousands. Oil companies set up a schedule of shifts in order that as many of their field men might attend as possible. It is said that the companies want a two-weeks' show in 1938 so that more time will be avail-

Jan 1, 1936

By George S. Rice

MANY studies on ground movement and subsidence have been carried on by members of the Institute during the past year, but only a few papers have reached maturity. Two of the mining schools of this country have continued their interest in ground movement research. At Columbia University School of Mines, Philip Bucky has continued his investigations, employing photoelastic methods and the use of his centrifugal apparatus for testing what he termed "the strength and behavior of mining structures." Helmut Landsberg, of The Pennsylvania State College, has developed a convergence recorder similar in principle to that used by the

Jan 1, 1936

By M. Smutz, C. J. Baroch, E. H. Olson

IN 1949 an orebody containing some 10 billion lb of recoverable rare earth metals was discovered in the Mountain Pass district of San Bernardino County, California.' The following year Molybdenum Corp. of America purchased a number of claims at the deposit and a mill on the property which had been constructed to process the district's gold ores. Average composition of ore from the San Bernardino deposit is less than 0.1 pct Tho2, 25 to 35 pct calcite, 10 pct rare earth oxides, 15 to 20 pct silica, and 30 to 40 pct barite.' Rare earth content of the ore analyzes 50.7 pct CeO2, 4.2 pct Pr6O11, 11.7 pct Nd2O3;, 1.3 pct Sm2O3,, and 34.3 pct La2O3 and others.' By floating the barite and depressing the bastna-site, Molybdenum Corp. of America produced a concentrate that contained 60 to 70 pct rare earth oxides. More than 25 pct of the rare earths, however, was lost in flotation. It seemed likely that a more economical method could be found. At the present time most of the rare earths in the concentrates are converted to rare earth chlorides, which are either fed to ion exchange columns for separation of the individual rare earths or reduced to misch metal. Current investigation shows that solvent extraction may achieve this separation more economically than ion exchange. The study reported here was undertaken to develop an economical method of preparing a pure rare earth nitrate mixture from California bastnasite ore. Results indicated that more than 98 pct of the rare earths could be recovered. Several possibilities were considered for processing bastnasite ore, but only the method outlined in Fig. 1 was investigated. This involved leaching the calcined ore with nitric acid. The nitric acid process is discussed under the following headings: 1) calcination of the ore, 2) leaching of calcine, 3) filtration studies, 4) solvent extraction, and 5) nitric acid recovery. Calcination: Since California bastnasite ore contains 25 to 35 pct calcite and about 10 pct bastnasite, calcination was needed to reduce the violence of reaction with nitric acid. Weight losses of 26 to 30 pct were obtained by calcining the ore at 900°C for I hr or at 800°C for 4 hr. Longer periods resulted in no further weight loss. Leaching the Calcine: When the bastnasite calcine was leached with 30 pct nitric acid for 8 to 10 days, rare earth recoveries of only 45 to 50 pct were

Jan 1, 1960