Search Documents

By H. C. Fiedler

Heats of high purity iron containing 3.1 pct Si and be -tween 0.0003 and 0.0295 pct N were prepared by vacuum melting ad then pouring while in a nitrogen atmosphere with the pressure between 0 and 90 psi. Strip from a heat with 0.0184 pct N underwent complete secondary recrystallization during the final anneal. Heats with less nitrogen had too few Si3N4 particles to restrain normal grain growth, and the heat with higher nitrogen had too many particles to allow complete secondary recrystallization. In the hot-rolled structure, Si3N4 precipitates only at the grain boundaries, with the consequence that annealing after hot-rolling diminishes the ability to subsequently undergo secondary recrystallization. In contrast to this behavior, ALNprecipitates uniformly in the hot-rolled structure. Under 1 atm of nitrogen, Si3N, in 3.1 pct Si-Fe dissociates between 900" and 950°C; the solubility of nitrogen increases from 0.0010 pct at 900" to 0.0030 pct at 1200°C. The solubility of nitrogen in Si-Fe has been the subject of many investigations. Corney and Turkdogan1 heated a 2.83 pct Si alloy in nitrogen and found the solubility, under 1 atrn of nitrogen, to be 0.0019 pct at 900°C. They claimed that Si3N4 did not form in the alloy above 705°C in 1 atrn of nitrogen. Fryxell et al.2 heated samples of 3.25 pct Si-Fe containing 0.0025 pct N over a range of temperatures and then analyzed for total nitrogen by vacuum fusion and for nitrogen in solution by a modified Kjeldahl technique. At 900°C, they reported the solubility of nitrogen in equilibrium with Si3N4 to be 0.0011 pct. pearce9 found the solubility of nitrogen at 900°C under 0.95 atrn of nitrogen to be 0.0017 pct in a 3.06 pct Si alloy. He reported that Si3N4 does not form above 770°C in 1 atrn of nitrogen. Although internal friction measurements have given somewhat higher values for the solubility,4-6 if the solubility of nitrogen is as low as has been reported by most investigators, and if Si3N4 is stable up to at least 945°C at 1 atrn pressure of nitrogen as reported by Seybolt,7 a small amount of nitrogen in properly processed Si-Fe should be effective in promoting secondary recrystallization. The requirement is that in the final heat treatment there be enough small, well-dispersed particles of Si3N4 to restrain normal grain growth. Fast8 has obtained secondary recrystallization by nitriding high-purity 3 pct Si-Fe after hot-rolling to a thickness of 0.118 in., followed by processing to 0.012 in., and annealing. A large amount of nitrogen, 0.076 pct. was introduced during the nitriding heat treatment, but he has since reported9 that "a few hundredths of a percent" is sufficient. Small amounts of aluminum10 or vanadium" nitride are capable of promoting secondary recrystallization. Heats containing as little as 0.010 pct A1 or 0.042 pct V and from 0.006 to 0.009 pct N underwent complete secondary recrystallization at final gage, whereas heats with lesser amounts of aluminum or vanadium did not.l2 To be reported is the behavior of nitrogen in high-purity 3.1 pct Si-Fe, and the relation of this behavior to the ability to undergo secondary recrystallization. PROCEDURE Ingots weighing 1 lb were made by vacuum melting high-purity electrolytic iron (A104, Glidden Co.) and high-purity silicon (Monsanto Co.). The latter was used in preference to ferrosilicon to insure a low aluminum content. The design of the melting furnace permitted pouring with the furnace atmosphere either below or above atmospheric pressure. Accordingly, at the completion of melting, nitrogen was admitted to the desired pressure and the heat then immediately poured. The ingots were sound, with no indication of porosity. In Table I are listed the heats investigated, the nitrogen pressure at pour, and the nitrogen and oxygen contents as determined by vacuum fusion with a platinum bath at 1850°C, a procedure which insures measurement of the total nitrogen.13 In addition, all heats contained 3.1 pct Si and not more than 0.002 pct C, 0.003 pct S or 0.005 pct Al. It was subsequently found that the quantity of nitrogen contained in the heats in Table I does not necessarily represent that obtained under equilibrium conditions. For example, the ingot poured immediately after 1 atrn of nitrogen was admitted to the chamber contained 0.0093 pct N, whereas an ingot poured 3 min after the nitrogen was admitted contained 0.021 pct N and another poured after a 6-min delay contained 0.029 pct N. While some bleeding of the hot top occurred in the latter instance, the ingot when examined in cross section appeared sound. The ingots were heated to 1325°C in hydrogen and rapidly rolled to 0.080 in. in 3 passes. The roll speed of the final pass was reduced so as to increase the quenching effect of the rolls. The hot-rolled pieces were processed both as-hot-rolled and after heating for 3 min at 900°C in hydrogen. After cold-rolling to 0.026 in., the strips were heated for 2 min at 900°C in hydrogen, then cold-rolled to the final gage of 0.012 in. The loss of nitrogen in going from the ingot to cold-rolled strip was no more than 10 pct. The final heat treatment, which was for the purpose of develop-

Jan 1, 1970

SAN FRANCISCO LOCAL SECTION Executive Committee G. HOWELL CLEVENGER, Chairman C. W. MERRILL, Pace-Chairman JAMES C. RAY, Secretary-Treasurer, 1235 Webster St., Palo Alto, Cal. F. W. BRADLEY ANDREW C. LAWSON Meets on the second Tuesday of each month Farewell Dinner to H. Foster Bain H. Foster Bain, Who has gone to London to assume the editorship of the Mining Magazine, was tendered a farewell dinner by the San Francisco Sections of the American Institute of Mining Engineers, the Mining and Metallurgical Society of America, and the Engineers' Club, on the evening of Mar. 9, 1915, at the Hotel Bellevue, San Francisco, 85 members being present. George H. Clevenger acted as Toastmaster and the following toasts were responded to: Bain and the Mining Industry, E. H. Benjamin. Bain, the Geologist, A. C. Lawson. Bain, the Man, F. W. Bradley. Bain, the Friend, C. W. Merrill. Bain, the Schoolboy, C.. F. Tolman. The Frontispiece and Flow sheet from the souvenir program, designed by James C. Ray, Secretary of the Section, are reproduced herewith.

Jan 5, 1915

By GEO M. FOWLER

AN appraisal of the activities of the mining geologists during 1936 clearly indicates the ever in- creasing utilization of geology in the search for ore. Few men with geo- logic training are idle at present; this is particularly true regarding recent graduates. Many have accepted employment in distant fields, such as the Philippines and South America, and greatly increased mineral production from these places reflects their activities. In North America, regions of intense mineralization formerly important are being restudied in greater de- tail and with better understanding; as a result, new mineral wealth is being found in many such districts. Much is being done by private companies and individuals, and it is to be hoped that mining companies will increasingly make available the purely scientific results of such studies by permitting their geologists to publish. On such generosity to a large extent will future advances in ore finding depend.

Jan 1, 1937

By B. M. Larsen, T. E. Brower

For some years we have been carrying on a rather comprehensive investigation of the occurrence of oxygen in liquid open-hearth steel. This investigation was interrupted by the war emergency and is therefore incomplete, with many questions still answered only partially, if at all; yet it seemed worth while to present a report of progress on this difficult field of research, if for no other reason than to promote discussion and further investigation of this important problem. The significance of such studies depends in large measure upon the accuracy of measurements of oxygen content in liquid steel while it is still in the furnace or as it flows into the ladle, or thence into the mold and there is, as we shall show, good reason for believing that the main source of uncertainty is in the sampling, not in the analytical method as such. The difficulty arises from the fact that any method of sampling is of itself apt to alter the amount of oxygen in solution in the liquid steel, because this oxygen is in a readily reactive condition. On the one hand, being usually present at a concentration appreciably in excess of that corresponding to equilibrium with the carbon then present, it may decrease rapidly in percentage by reaction with carbon and evolution of CO, especially if the liquid metal is in any way shaken or brought in contact with a cooler solid surface. On the other hand, it may increase rapidly by ab- sorption of oxygen from a slag, a furnace atmosphere, or from air. These circumstances, which are inherent in the problem, as well as our conclusion that, despite the considerable amount of careful work already done, there is still no method of sampling liquid steel acceptable as an unquestioned standard, ed us to undertake systematic comparisons of oxygen content of large numbers of samples taken: (I) by a single method at different positions and levels in the bath; (2) at the same place by different sampling methods; and (3) from bath, tapping stream and pouring stream. The different sampling methods yield somewhat different values and there is as yet no way to tell with certainty which is the most accurate. But the general reproducibility and consistency of the results give us some confidence in certain inferences we draw from them: namely, that the "spoon" method of sampling, properly carried out, gives somewhat more consistent results than the "bomb" method, as it has usually been practiced; that, in the bomb method, an aluminum cap is preferable to a steel cap; that the oxygen content of liquid steel in a finished heat is substantially the same all over the bath at the same level, and tends to decrease at lower levels further from the slag interface; also that it tends to decrease, and to decrease erratically, from furnace bath to tapping stream entering the ladle. Accordingly it seemed desirable to report these observations in detail as a first step, so that the reader may judge their significance as a contribution towards solution of the main problem, which is to find a means of pre-2

Jan 1, 1945

Meeting of June 26, 1914.-The President was authorized to appoint Advisory Committees to co operate with the United States Bureau of Mines. The President announced the appointment of Edward H. Benjamin and W. C. Ralston as additional members of the Committee on Arrangements for the San Francisco meeting, 1915. H. T. Van Ells and Judd Stewart were appointed to represent the Institute on a joint committee of several technical societies to consider the standardization of graphical methods for the presentation of statistics. The President announced the appointment of H. Foster Bain to succeed Edward H. Benjamin, resigned, on the Committee of Management of the International Engineering Congress, 1915. The Secretary was authorized to issue a new circular advertising the sale of back Transactions and to sell back Transactions, bound in cloth, at a price of $35 for 46 volumes, provided sufficient orders were received to warrant the special binding. The sum of $177.50 was contributed to the San Francisco Local Section. Upon recommendation of the Committee on Membership, 70 Members, 4 Associate Members and 7 Junior Members were elected to their respective classes; there was also one change of status from Junior Member to Member.

Jan 8, 1914

A New Ingersoll-Rand Turbo Blower The Ingersoll-Rand Co. has added to its Turbo Compressors and Blowers a low-pressure machine t o handle volumes from 3,000 to 35,000 cu. ft. per minute at from 1-2 ½ lb. These are particularly adapted to such service as foundry cupola blowing, atomizing oil for oil burners, supplying blast to heating and annealing furnaces of various kinds, blowing air for water-gas generators, pneumatic conveying and ventilating. They are of the single stage, double flow type and are furnished either electric motor, steam turbine or water wheel driven.

Jan 6, 1916

By Thomas F. Donnelly

The Province of San Cristobal is situated on the south side of the island of Santo Domingo about 25 miles west of Santo Domingo city, the capital of the republic. The copper mineraliza,tion is found about 8 miles north of the town of San Cristobal,. in the section known as Bucaro Hill; in San Francisco Hill; on the Nigua River; and on the Jaina River. The district is reached by automobile from Santo Domingo city over an excellent road for 25 miles to San Cristobal, and then, by horseback 6 or 8 miles up the Nigua River to what is locally known as "Camp

Jan 1, 1916

By Walter Wood

The specifications for cast-iron pipe that have been submitted at this meeting are practically the outgrowth of those which were originally adopted, about 1860, by Mr. Kirkwood of Brooklyn, N. Y. They have been changed but little since that time, the mode of testing pipe in the hydraulic press, as well as the method of coating, not having departed from the original practice. The chief addition to the specifications has been in the adoption of a test-bar 2 in. by 1 in. in crosa-section, broken between 24-in. supports by a transverse strain applied on the flat side. Test-bars were first introduced into pipe-specifications about 1870. At that time a satisfactory test-piece had to stand a tensile strain of 16,000 lb. per square inch. The present test-bar was adopted in order to give some idea of the deflection of the iron that was being used. These deflection-tests have been so satisfactory to both engineers and manufacturers, and have met the requirements of the pipe-trade so accurately, that it is considered best to hold to the . 2-in. by 1-in. bar instead of adopting the short " Arbitration Bar," which yields but little information from the stand-point of deflection. The new feature in these specifications is the effort to reach standards to which pipe shall be cast in the future, thus permitting the manufacturer to make up stock and the purchaser to find material on hand when he asks for deliveries. Heretofore there has never been ally standard weight for pipes? although in some sizes certain weights are more frequently asked for than others. The fixing of standards for pipes permits the adoption of definite standards for fittings. It has been aimed to secure such uniformity for fittings as will permit the same class of fittings to cover two or more classes of pipe. In order to accomplish

Jan 1, 1905

By Earl Hanson

FIRES in heavily timbered mines are disastrous, involving danger to both life and property. Some mines have been completely ruined or so heavily damaged that reopening them would not pay. Though few mines are entirely free from danger of fire, the risk is minimized by proper care and good design of plant. The Tintic Standard mine is at Dividend, Utah, in the famous Tintic mining district, about 60 miles south of Salt Lake City. The development of the mine was begun in 1907 by the late Mr. E. J. Raddatz and his associates. From the beginning, the work was hampered by high rock temperatures and the presence of high concentrations of rock gases such as carbon dioxide and nitrogen. Development work was carried on with great perseverance for nine years, and resulted in the discovery of ore in 1916. The total production of the Tintic Standard mine to Jan. 1, 1936, amounted to 1,664,388 tons of ore, having a gross value of .$61,996,719.

Jan 1, 1936

By Charles Will Wright

MINERAL production in almost all European countries suffered a sharp setback because of the war. Plants were damaged, transportation facilities disrupted, and labor dispersed and demoralized. Since the war, due to lack of confidence and economic stability, there has been little incentive to rebuild and expand the mineral industries even though a big demand at high prices exists for mineral products. Most mining and metallurgical companies in Europe hesitate to invest their capital because of the tendency towards nationalizing industry, high taxes, and low output of labor, as well as the deficiency of mine supplies and equipment within their countries. In short, they do not have faith in the future, and for these same reasons and fears most of the mining companies in America will not risk capital investment in Europe. In Europe, including the United Kingdom, free enterprise has been losing ground and as a result the foundation of their economic welfare is being undermined. American mining interests willing to take the initiative could help in counteracting this influence if a way were found for them to co-operate with the European producer without too great a risk.

Jan 1, 1948

By R. G. Jones, W. L. Kinney, R. E. Schilson, R. S. Wilson, G. A. Clark, H. Suralo

This paper describes the field opeturluns at the Fry in situ combustion project in Crawford County, 111. Field operations may be divided into three phases—-preliminary engineering studies of 1960 and 1961, ignition, and, finally, operation of the test. The Fry combustion project was a pilot test of cocur-rent in situ combustion on a 3.3-acre inverted five-spot. In the summer of 1960, air injection tests were conducted using old wells in the area and a new air injection well drilled especially for the test. In the summer of 1961, four new oil wells were drilled on a 3.3-acre pattern for the pilot test. All old wells in the near vicinity of the pilot test were abandoned to preclude any possibility of gas escaping to adjacent formations. A compressor plant was also installed at the test site in 1961. Air injection tests and other engineering studies were made. At the conclusion of these tests, ignition was accomplished with a 40 kw electrical igniter. Operation of the Fry combustion test was little different from the usual oilfield operation with the exception of the high rate of air injection. No difficulty was found with the openhole completion. There were no unusual corrosion or emulsion problems until bottom-hole temperatures exceeded 150F. Four cores were drilled into the burned-out portion of the reservoir with no mechanical difficulties. INTRODUCTION A cocurrent or conventional in situ combustion test was conducted on the Fry unit of the Marathon Oil Co., in Crawford County, Ill. Besides testing combustion in the Fry type of reservoir, the test was intended to evaluate various operating procedures. This paper presents a discussion of the Fry combustion test field operations. The geology of the reservoir and the test performance are discussed in other papers.'.' HISTORY OF THE FRY UNIT The Fry unit consists of 11 leases totaling 337 acres in an area in which oil was originally discovered in 1906. Production from this reservoir, as from all Robinson sand reservoirs in the area, was very high during the first few years. As the dissolved-gas energy was dissipated, early attempts to retard the decline consisted of vacuum, air, and gas repressuring, and recently, most of the area has been subjected to water flooding. Following early air repressuring, the Fry waterflood unit was formed and water flooding initiated in July, 1952. In the area in which the Fry combustion test was conducted, a peripheral water flood of a 160-acre area was developed as shown in Fig. 1. Between 1956 and 1960, it became apparent that the water flood was unsuccessfd. In looking for a suitable site for an in situ combustion test, the Marathon Oil Co. selected the Fry unit as possessing those features most desirable for such a research project. Field operations associated with the Fry combustion test began in the spring of 1960.

Jan 1, 1966

By Fred C. Bond

JUST four years ago, in March, 1930, Gilbert LaBine discovered the rich deposit of pitchblende and silver ore on the east shore of Great Bear Lake, 30 -miles south of the Arctic Circle, which brought a new mining district into being. His original discovery is now the property of Eldorado Gold Mines, Ltd., but other groups have been active. Vigorous prospecting has outlined a mineralized zone that extends at least 100 miles from north to south. In this area silver discoveries have been relatively common; pitchblende, as might be expected, has been harder to find, though a deposit has been located this spring nearly 100 miles south of Eldorado that may be of great importance.

Jan 1, 1934

By William H. Waggaman

CURTAILMENT of the mineral industry as a whole undoubtedly will follow world peace, but the output of certain minerals should pursue a course well above the average on any curve of probable output projected beyond the trends exhibited through 1939. Without speculating on industrial conditions in the pending recomversion period, demand for fluorspar should be greater than before the war because of these factors, introduced by or resulting directly from military necessity: (1) Discovery and development of new deposits. (2) Improved technology in benefication. (3) New and expanded uses for fluorspar and its derivatives. The steel industry has been and continues to be the greatest consumer of fluorspar, and it wag largely to meet the wartime needs for steel that the domestic fluorspar industry has been expanded so greatly. Not only were the search for and development of new deposits of this mineral considered esstinal but the marginal nature of some of the,c- domestic deposits made it necessary to improve mineral dressinc and processing techniques to utilize them

Jan 1, 1945

By Herty, C. H.

The effect of temperature on the physical properties of structural materials has been the subject of many investigations during the past decade. The literature on the effect of elevated temperatures. is voluminous, and during the last four years a great deal of experimental work has been carried out on the effect of low temperatures on the impact properties of steel. For many engineering purposes it is important to know the shock resistance of steels at low atmospheric temperatures, and with the ever-developing field of refrigeration and separation of materials at low temperatures, the normal limits of atmospheric temperature have been exceeded in practice. Iron and its alloys in the unnotched condition have a high impact strength at low temperatures, but in practice variations in type of notches result either from design or accidentally through scratches and surface or internal defects. A study of notched bar impact tests is, therefore, highly important to the engineer. A survey of the literature on low temperature impact testing indicates that chemical composition, heat treatment and method of testing have been the variables which have been considered in most previous work. In only a few instances has any mention of the steel- making method been mentioned and in these the comparison was between steel-making processes and not between steel-making methods on the same process. In view of the wide variations in impact properties at room temperature, in quench and strain ageing and in grain growth of steels of identical chemical composition, (by this is meant the usual five element analysis reported), it was felt

Jan 1, 1957

By B. E. Field

COBALT is a silvery white metal with a slight bluish cast, strongly resembling nickel in its appearance and properties, notably its resistance to corrosion, although its alloys with other metals differ quite decidedly in their properties from those of nickel. The name cobalt was derived from the German "Kobold" meaning goblin and this came to be applied to the cobalt minerals which, although they resembled ores, did not readily yield metal when smelted by the primitive processes available in the Middle Ages. Cobalt minerals were used as pigments by potters and glass workers before the Christian era. Cobalt blue glass was found in the tombs of the Egyptians and in the ruins of Troy, and many colors used by the ancient Greeks and Romans contained cobalt. The ancients were entirely unaware that the colors they used were caused by cobalt and the metal itself was only isolated about the middle of the eighteenth century by Brandt although the preparation of cobalt compounds had been carried on in a small way ever since the opening of the silver-cobalt deposits at Schneeberg, Germany, in 1470. The metal is fairly hard, with a density when pure of 8.81 in the cast state and 8.92 after working. The com¬mercial grade of cobalt has a density of about 8.75 in the cast state. The atomic weight is 58.97. The Brinell hardness of the pure metal is 124; that of the commercial grade varies from as low as 100 to as high as 138, depending upon the impurities present. Pure cobalt has a sharp melting point at 1478°C. The tensile strength of the pure metal in the cast condition is said to be higher than that of any other pure metal. Kalmus gives it as 34,400 lb. per sq. in. for cast unannealed metal; the effect of annealing at 850 to 900°C. is to raise the strength slightly. The yield point is close to the ultimate strength and the reduction in area and elongation are both low. Mechanical working raises the tensile strength of pure cobalt rapidly and in the form of wire it will be over 100,000 lb. per sq. in. The presence of small quantities of carbon in the commercial metal raises the tensile strength to as high as 61,000 lb. per sq. in., the reduction in area and elongation being raised at the same time to approximately 20 per cent.

Jan 1, 1933

By Oliver Bololes

UNDER the able leadership of Samuel H. Dolbear, the Committee on Nonmetallic Minerals furnished a program of sixteen papers comprising three sessions. An outstanding accomplishment in technology presented at the first session by Benjamin L. Miller and C. H. Breerwood is the application of flotation to the purification of limestone used in cement manufacture. In place of selective quarrying to provide high-grade raw material, the quarry-run stone is pulverized and treated in froth flotation cells for removal of free silica and mica. Some advantages are cheaper quarrying, more complete utilization of quarry rock, avoidance of purchasing high calcium stone, lower fuel cost and improvement in the finished cement. Paul M. Tyler presented the general subject of milling methods as applied to nonmetal lies. He pointed out the importance of some of the more recent refinements in ore dressing, and urged the need of a wider appreciation of their possibilities. The gypsum industry of Canada was described by L. H. Cole. Crystal growth during the setting process was illustrated by moving pictures. The Coastal Plain and interior salt

Jan 1, 1935

By John W. Crutchfield, Emil F. Bowers

This paper presents the initial results of a pressure maintenance by water return project in the Lower Pawelek reservoir of the Falls City Field, Karnes County, Southwest Texas. Production is from the Lower Wilcox section at an average depth of 6,030 ft on the downthrown side of a "down to the coast" fault. Of particular interest is that the reservoir oil is high gravity and low viscosity but far undersaturated with gas at the original reservoir pressure and temperature. The early pressure and production history indicated only a partial or limited water drive, and this fact, coupled with the characteristics of the reservoir fluid and artificial lifting problem.. made advisable the water injection program to maintain reservoir pressure. The paper includes a description of the reservoir and reservoir fluids, the pressure and production history, a description of the water injection facilities, and the results of reservoir calculations involving Hurst's unsteady state flow and the material balance equations for calculation of water influx and prediction of the pressure-production relationship at various rates of withdrawal. The reservoir calculations and initial field results indicate that reservoir pressures in excess of 85 per cent of original pressure can be maintained by control of water injection even at very high rates of production. INTRODUCTION The purpose of this paper is to report the initial results of a pressure maintenance by water return program in the Lower Pawelek reservoir, Falls City Field, Karnes County. Texas, and to calculate an empirical relationship between pressure and production in this limited or partial water drive reservoir. Location The Falls City Field (Fig. 1) is located two miles north of the town of Falls City in Karnes County, Texas, and is approximately 50 miles south-southeast of San Antonio on U. S. Highway 181. Discovery and Development The initial block of leases was taken after a surface geological survey identified a major east-west fault and closure on the south or downthrown section. The discovery well, Southern Minerals Corporation's Joe F. Bartosch 1; was completed at 4,650 ft in the Lower Bartosch sand in December, 1944. Drilling was continuous until December, 1946, and resulted in the discovery of 12 oil reservoirs between 4,600 and 6,050 ft in the Middle and Lower Wilcox formations. These are shown on the cross-section (Fig. 2). As of the current date there are 64 oil wells completed as follows: Southern Gulfshore Magnolia Minerals Oil Petroleum Reservoir Corp. Co. Corp. Total Upper Bartosch 0 0 0 0 Lower Bartosch 16 0 0 16 Shulze 7 0 1 8 Upper Faires 2 0 0 2 Lower Faires 4 0 0 4 Upper Moczygemba 0 0 0 0 Lower Moczygemha 2 0 0 2 Olinick 2 0 0 2 Upper Martinez 0 0 0 0 Lower Martinez 5 0 0 5 Upper Pawelek 0 0 1 Lower Pawelek 27 1 3 31 Total 65 2 4 71

Jan 1, 1950

By W. A. Hockings, D. W. Fuerstenau, A. L. Mular

This paper briefly describes a simple air pycno-meter and its use for rapid determination of the composition of mixtures of solid particles. Research on such problems as the pelletizing of solids, the mixing of solid particles, and the comminution of mixtures can be simplified by means of this analytical tool. THEORY OF OPERATION Liquid pycnometers1 are commonly employed to measure volumes. These devices are time consuming and sometimes give inconsistent results. The liquid used in the pycnometer may have an undesired influence on the material to be measured; moreover, complete displacement of air by the liquid is seldom

Jan 1, 1963

By O. E. Kiessling

THIS announcement of the topics relating to production control, which the Committee hopes to have discussed at the February meeting, supplements the preliminary announcement published in the November number of MINING AND METALLURGY. In the previous article, the writer indicated the kaleide-scopic nature of the questions involved in obtaining better coordination in industry, and that, as a matter of practical expediency, the discussion in February would be limited to the more obvious difficulties in industry which need attention and to those questions which the Committee thinks would be of greatest interest to members of the Institute. But while practical considerations necessitate limiting the program, free discussion of all phases of the subject is urged by 'the Committee. In a preliminary consideration of the production control problem, there loom up two questions which have to be faced: (1) First, there is the question of the extra industrial capacity necessary to meet demand during the ordinary fluctuations of business, commonly characterized as `the "business cycle." Anyone who tries to formulate a program pertaining to productive capacity must decide whether he wishes to discuss the control of business cycles. While this question may eventually lend itself to treatment, the Committee does not feel that it can be considered at present with much profit. (2) The second question arises from the existence of over-stimulated capacity above and beyond peak demands in boom times. Discussion of this topic, it is felt, would be most fruitful. How to prevent capacity from being over-stimulated to an extent beyond any hope of possible demand is a

Jan 1, 1929

By Leo F. Reinartz

Part II of a four-part series on the history of steelmaking in the US, points out the inadequate safety and living conditions that existed in steel mills at the turn of the Century. Also defined are furnace and process developments. OPERATIONS in steel plants today are highly mechanized. Men work in light, clean, orderly melting shops, making it difficult for old timers to convince young men that primitive, hazardous conditions existed in steel plants at the turn of the century. Working conditions then were very poor as compared to present day standards. In small plants especially, sanitary, locker, and washroom facilities, first-aid practices and stations were un- known Accidents were frequent and severe. Workers had a fatalistic attitude toward getting hurt. He who had an accident was looked upon as a hero. A dirty bandanna often served as a bandage. Infections were frequent. Electric cranes were in their infancy and broke down often Cables had not as yet replaced chains. Pig iron and scrap iron were loaded by hand in the stockyard, and stockyard locomotives were un- known; mules served as the usual motive power. It was not unusual to see recorded a delay of ½ hr in charging a furnace because of a balky mule. Furnace operations A few plants had primitive charging machines, but most furnaces were charged by placing scrap or pig iron on the paddle of a long peel, which rested on a bar across the furnace door opening. Laborers at the handle end of the peel, using the bar as a fulcrum, would heave the material into the furnace by a down and sideward motion of the peel handle. In time they became expert in placing these materials in the furnace, but it was hard, hot work, and a long time was required for charging. Cold charges of 25 tons required more than 12 hr for melting and re- fining the steel. Ports, doors, and frames were not water cooled. The charging and working area in front of the furnace was covered with steel plates. They were hot and often warped by the intense heat of the un- insulated checker chambers directly below. In the summer, working conditions on the charging floor were almost unbearable. Silica refractories were of poor quality. Because of this, and the inadequate training of furnace men in fuel control and furnace operations, roofs, front and back walls, and ends burned out rapidly. Dolomite machines were unknown; consequently, furnace banks and hearths were fettled with dolomite by the use of hand shovels. The round system required six or more men. Each man took a shovelful of dolomite and, in his turn, deposited it on the back wall and bank by a dexterous forward swing and twist of the shovel. The upward swing of the shovel partially protected his face from the searing heat of the furnace coming out through the wide-open door. Considerable skill and stamina were required to do this job properly. Reverse valves, usually of the cast-iron butterfly type, were located below the charging floor. They were operated by long levers on the charging floor level men they became warped, because of heat and abuse, great strength and skill were required to reverse them. Furnace operations were difficult. The quality and quantity of producer gas coming from irregularly stoked, hand-operated gas producers was uncertain and unreliable. Furnace Linings and ports were quickly burned out. Poor bottom and side-wall refractories, indifferent and inexperienced crews, as well as irregular re-

Jan 1, 1961