Search Documents

By J. H. Waxweiler, L. C. Ikenberry, R. J. Bendure

Carbon which is present as insoluble carbides in austenitic stainless steels can be measured quantitatively by dissolving the steel in iodine-methanol and analyzing the residue for carbon. Severe sen-sitization was observed in Type 302 due to precipitation of only 0.003 pet carbon. Both cold work and the presence of delta ferrite caused a marked acceleration in rate of carbide precipitation. Carbide precipitation rates in 17-7 PH were stzulied for the austenite conditioning and also the aging heat treatment. CARBON and its compounds exercise a major influence on the properties of stainless steels and their response to thermal treatment. Sensitization in 18-8 type stainless steels has been the subject of numerous investigations throughout the years. Bain, Aborn, and utherford," and Binder, Brown, Frankss all studied the effects of heating austenitic stainless steels in the temperature range of 1000° to 1500°F. The primary purpose of most of these studies was the investigation of susceptibility to in-tergranular attack in acids due to these sensitizing heat treatments. Intergranular precipitation of carbides was always associated with intergranular attack but it was recognized2 that severe attack could occur with but minute quantities of precipitated carbide. Mahla and ielsen utilized the electron microscope to make a significant contribution in illustrating the appearance and method of growth of chromium carbides during sensitizing heat treatments. However, as they stated, their studies of residues could not be used to obtain a quantitative measurement of the amount of carbon which was actually precipitated. The aim of the present investigation was to devise a relatively fast, simple method for the quantitative measurement of carbides in stainless steel. EXPERIMENTAL WORK The initial investigations were made to determine the best means of separating carbides from the matrix. A number of dissolving media were tried using both chemical and electrolytic attack. Qualitative examination of the extracted residues by X-ray diffraction indicated that solution in iodine-methanol would furnish a good means of separation. Consequently, further work was pursued along this line. The method is quite simple. The sample in the form of millings or nibblings is dissolved in iodine-methanol solution at room temperature (6-g iodine, 25-ml methanol per g of sample). The insoluble residue containing the carbides is separated by suction filtration through an ultra-fine glass filter disc. This is a very fine filter medium that will retain particles as small as 0.1 to 0.2 p in diameter. After washing with methanol and drying, the filter disc and residue are placed in a conventional combustion carbon-tube furnace and the carbon determined gravimetrically. Using this technique it was found that reproducible insoluble carbon values were obtained. However, since such small amounts of insoluble carbon were obtained on Type 302 after sensitizatipn at 1250°F and 1500°F, the values were confirmed by a second method. In the second method the sample was dissolved with copper potassium chloride and filtered through a millipore paper. This treatment dissolves the matrix but leaves undissolved practically all of the carbon irrespective of how it is present in the steel. The amount of insoluble carbon present as chromium carbide is determined by calculation from the analysis of the residue for chromium and iron. The derivation of the formula used for this calculation is discussed later. The values obtained by the indirect copper-potassium-chloride method were in agreement with those obtained by the iodine-methano1 method. See Table I. It should be pointed out that the sensitivity of the direct combustion method is not too high when the amount of carbide present is small. This is due primarily to inherent blanks and to analytical errors such as weighing. For this reason it cannot be stated with any degree of certainty that there is a significant difference between values of 0.002 and 0.005 pct. Having confirmed that the iodine-methanol extraction gave a quantitative measurement of the precipitated carbides in Type 302, exploratory tests were conducted on Armco 17-7 PH stainless steel. Samples from commercial Heat 54807 were solution annealed at 2000°F, water quenched and heated at 1250" and 1500°F, and water quenched. The analysis of Heat 54808 is as follows:

Jan 1, 1962

By Charles Legrand

The power plant of the Burro Mountain Copper Co. is located near Tyrone, N. M., at 5,950 ft, elevation. It is interesting because it uses the largest stationary Diesel engines in the United States. The general layout of the plant is shown in Figs. 1 and 2. The building is of steel-frame construction with hollow-tile walls and corrugated-iron roof; the floor is concrete and all windows have steel frames, making a fireproof building. The building is made to accommodate one more electric generator unit, which is being installed; also two 4,000-cu. ft. air compressors direct-connected to three-cylinder engines with the same size cylinders as the electric units. The power plant consists of two 815-kva., 60-cycle, three-phase, 6,600-volt, 180-r.p.m. generators, direct-connected to five-cylinder, two-cycle Diesel engines; the necessary circulating pumps for cooling water, cooling towers and oil storage tanks. A portion of the power is used in the same building as the generating units to run one of two 200-kw. rotary converters delivering 260-volt direct current, and a 2,500-cu. ft. air compressor, delivering air at 95 1b.-pressure, direct-connected to a 400-hp., 6,600-volt, three-phase synchronous motor. The remainder of the power is used to run a 1,500-ton concentrating mill 3 1/2 miles from the power house, various hoists, pumps and motors about the mines and the lighting and water-works of the town of Tyrone. The direct current is used for electric traction in the mine, also to run hoists and motors that were installed before the new power plant was built. Due to the large hoists that take starting peaks of 250 kw. and the 10-ton electric locomotive that takes at times 150 kw., the load is extremely variable, as shown in Fig. 3. The two five-cylinder vertical Diesel engines, which are rated at 1,250 b.hp. at sea level, have cylinders of 525-mm. diameter (20.6 in.) and

Jan 1, 1917

By T. A. Pollard, C. R. Sandberg, E. B. Elfrink

This paper presents an evaluation of compressibility factor data and a discussion of their application to the estimation of gas reserves. A correlation is presented which provides compressibility factors for use in both two-phase and single-phase hydrocarbon systems. Accuracies comparable to those obtained previously for single-phase systems only can be expected. A simple means of predicting the presence or absence of a liquid phase in a condensate system of known composition is illustrated. The correlation is based on 1,030 compressibility determinations from 21 hydrocarbon samples taken from eight oil fields. Of the data used, 75 per cent were from California, 15 per cent were from the Mid-Continent area, and 10 per cent were from South America. The average numerical deviation of the experimental data from this compressibility chart is 1.22 per cent. Charts and tables are included and discussed which illustrate the errors involved through the misuse or nonuse of compressibility factors in estimates of gas-in-place. INTRODUCTION The compressibility factor is a coefficient which expresses the deviation of a gas of given composition from the Perfect Gas Laws. A factor such as this is necessary in any calculation involving volumes of gaseous mixtures, and finds extensive application in the estimation of natural gas and condensate reserves. It is used in the decline curve, the volumetric, and the material balance methods of gas reserves estimation. The behavior of gases at high pressures has been investigated extensively in recent years and considerable data have been assembled on the compressibility characteristics of a number of gases. Notable among the investigators of high pressure gas relationships are Kvalnes and Caddya, Kay" Sage and Laceys, and Brown, Standing" and Katz4. Other contributors are Smith and Watson, Roland and Kaveler', and Stevens and Vance". The data on compressibility factors assembled by these investigators have been presented and correlated in numerous ways; particularly noteworthy is the method first presented by Kay5 which relates compressibility factor "Z" to pseudo-reduced temperature and Pseudo-reduced pressure. Other investigators have used this empirical relationship successfully and numerous charts covering a large number of gases have been constructed on this basis. It is the purpose of this paper to evaluate compressibility factor data and to illustrate the importance of their proper use in the estimation of gas-in-place for both gas and condensate reservoirs. EVALUATION OF COMPRESSIBILITY FACTOR DATA The compressibility chart presented by Standing, Katz, Brown and Holcomb in 1941 is probably the most recent and reliable chart for natural gases. The reliability of the Katz chart has been investigated by the writers for a fairly large number of gases (single-phase) in the pressure range from 500 to 10,000 psia and temperature range from 80 to 400°F. A summary of this comparison is presented in Table I. The numerical average deviation of the chart compressibility factors from the experimental compressibility factors is 1.05 per cent, and the algebraic deviation is -0.28 per cent. The Katz correlation appears to be quite accurate for single-phase hydrocarbon systems. It was based on single-phase systems and does not necessarily provide a means of accurately predicting the behavior of two-phase systems which might be encountered in condensate work. Data published recently by Sage and Oldsl' have enlarged the knowledge of phase behavior in condensate systems by covering extensively the Compressibilities of systems in the two-phase as well as single-phase regions for a wide range of temperatures, pressures and gas-oil ratios. An evaluation of these data indicates that conditions can arise, especially in condensate systems having fairly low gas-oil ratios, in which two phases occur and the usual gaseous compressibility factors do not accurately apply. The measured PVT data of Sage and Olds covering two-phase systems have been correlated with additional such data from the Mid-Continent area and South America; these are presented in Fig. 1. This chart is the result of 1,030 compressibility* determinations from 21 hydrocarbon samples taken from eight oil and condensate fields. Of the data used, 74.75 per cent were from California, 15.45 per cent were from the Mid-Continent area, and 9.80 per cent were from South America. The chart construction is based on the original

Jan 1, 1949

By H. J. Ramey

Conventional calculation of total system isothermal compressibility for a system containing a free gas phase involves, among other things, evaluation of the change of oil and gas formation volume factors and the gas in solution with pressure. Preferably, this information should be obtained from laboratory measurements made with particular oils and gases. Often, experimental measurements are not available. In this case, it is necessary to obtain pressure-volume-temperature relationships from general correlations such as those of Standing' for California oils. In order to speed estimates of compressibility, generalized plots have been prepared of the change of both oil formation volume factors and gas in solution, with pressure from Standing's correlations. A generalized plot for estimating the change in the two-phase (oil and gas) formation volume factor with pressure is also presented. Usually, the effect of gas dissolved in reservoir water upon the total system compressibility is neglected for gas saturated systems, due to the low solubility of gas in water. Results of this study indicate that the increase in total system compressibility caused by solution of gas in water is often as large as the compressibility of wafer, and can be magnitudes larger for low pressure systems. Generalized results for estimating the change of gas in solution in water with pressure are presented in tabular and graphical form. INTRODUCTION During the past decade, pressure build-up and drawdown techniques have gained an important place in reservoir engineering. Build-up and drawdown analyses are only two special applications of the broad field of transient fluid-flow theory. All solutions of transient fluid-flow problems contain a parameter called the total system isothermal compressibility. This property of fluids and porous rock is a measure of the change in volume of the fluid content of porous rock with a change in pressure, and it may vary considerably with pressure. Evaluation of total system isothermal compressibility is not difficult, but it is tedious and time-consuming. Often compressibilities are estimated roughly, or transient flow methods are neglected completely. The benefits of using accurate system compressibility in properly-executed build-up or drawdown analyses are: 1. Better planning of pressure build-ups may be achieved to avoid unnecessary loss of revenue due to excessively long shut-in periods, or to shut-in periods too short to yield useable data. 2. Better and more reliable estimates of static formation pressures for reserves estimates and rate performance estimates. 3. Reliable information for evaluation of well completion effectiveness, and planning and interpretation of well stimulation efforts. The purpose of this paper is to clarify the nature of the total system isothermal compressibility, and to present useful methods for estimation of compressibility, particularly for systems containing a gas phase. DEVELOPMENT Numerous publications have presented solutions to transient single-phase flow of slightly compressible fluids, stressing pressure build-up applications. In transient flow, a compressibility* term arises to permit volume content of fluids in porous rock to change as pressure changes. The basic nature of the compressibility term is usually taken for granted. Problems arise in practical applications of transient fluid theory because most published works consider only one flowing fluid—in an ideal porous system containing only one fluid. In 1956, Perrine2 presented an intuitive extension of single-phase flow pressure build-up methods to multiphase flow conditions. Later, Martin- established conditions under which Perrine's multiphase build-up method had a theoretical foundation. Perrine has shown that improper use of single-phase build-up analysis in certain multiphase flow situations can lead to gross errors in estimated static formation pressure, permeability and well condition. It is likely that, much pressure build-up data for oil wells should be analyzed on the basis of multiphase flow. For both single-phase and multiphase build-up analysis, the isothermal compressibility term in dimensionless time groups often should be interpreted as the total system compressibility. All real reservoirs contain one or more compressible fluid phases. In addition, rock compressibility can contribute in an important way to the total system compressibility. The proper total system compressibility expression may contain terms for compressibility of oil, gas, water, reservoir rock and terms for the change of solubility of gas in liquid phases.

Jan 1, 1965

By C. R. Sandberg, T. A. Pollard, E. B. Elfrink

This paper presents an evaluation of compressibility factor data and a discussion of their application to the estimation of gas reserves. A correlation is presented which provides compressibility factors for use in both two-phase and single-phase hydrocarbon systems. Accuracies comparable to those obtained previously for single-phase systems only can be expected. A simple means of predicting the presence or absence of a liquid phase in a condensate system of known composition is illustrated. The correlation is based on 1,030 compressibility determinations from 21 hydrocarbon samples taken from eight oil fields. Of the data used, 75 per cent were from California, 15 per cent were from the Mid-Continent area, and 10 per cent were from South America. The average numerical deviation of the experimental data from this compressibility chart is 1.22 per cent. Charts and tables are included and discussed which illustrate the errors involved through the misuse or nonuse of compressibility factors in estimates of gas-in-place. INTRODUCTION The compressibility factor is a coefficient which expresses the deviation of a gas of given composition from the Perfect Gas Laws. A factor such as this is necessary in any calculation involving volumes of gaseous mixtures, and finds extensive application in the estimation of natural gas and condensate reserves. It is used in the decline curve, the volumetric, and the material balance methods of gas reserves estimation. The behavior of gases at high pressures has been investigated extensively in recent years and considerable data have been assembled on the compressibility characteristics of a number of gases. Notable among the investigators of high pressure gas relationships are Kvalnes and Caddya, Kay" Sage and Laceys, and Brown, Standing" and Katz4. Other contributors are Smith and Watson, Roland and Kaveler', and Stevens and Vance". The data on compressibility factors assembled by these investigators have been presented and correlated in numerous ways; particularly noteworthy is the method first presented by Kay5 which relates compressibility factor "Z" to pseudo-reduced temperature and Pseudo-reduced pressure. Other investigators have used this empirical relationship successfully and numerous charts covering a large number of gases have been constructed on this basis. It is the purpose of this paper to evaluate compressibility factor data and to illustrate the importance of their proper use in the estimation of gas-in-place for both gas and condensate reservoirs. EVALUATION OF COMPRESSIBILITY FACTOR DATA The compressibility chart presented by Standing, Katz, Brown and Holcomb in 1941 is probably the most recent and reliable chart for natural gases. The reliability of the Katz chart has been investigated by the writers for a fairly large number of gases (single-phase) in the pressure range from 500 to 10,000 psia and temperature range from 80 to 400°F. A summary of this comparison is presented in Table I. The numerical average deviation of the chart compressibility factors from the experimental compressibility factors is 1.05 per cent, and the algebraic deviation is -0.28 per cent. The Katz correlation appears to be quite accurate for single-phase hydrocarbon systems. It was based on single-phase systems and does not necessarily provide a means of accurately predicting the behavior of two-phase systems which might be encountered in condensate work. Data published recently by Sage and Oldsl' have enlarged the knowledge of phase behavior in condensate systems by covering extensively the Compressibilities of systems in the two-phase as well as single-phase regions for a wide range of temperatures, pressures and gas-oil ratios. An evaluation of these data indicates that conditions can arise, especially in condensate systems having fairly low gas-oil ratios, in which two phases occur and the usual gaseous compressibility factors do not accurately apply. The measured PVT data of Sage and Olds covering two-phase systems have been correlated with additional such data from the Mid-Continent area and South America; these are presented in Fig. 1. This chart is the result of 1,030 compressibility* determinations from 21 hydrocarbon samples taken from eight oil and condensate fields. Of the data used, 74.75 per cent were from California, 15.45 per cent were from the Mid-Continent area, and 9.80 per cent were from South America. The chart construction is based on the original

Jan 1, 1949

By P. C. J. Gallagher

A number of recmt determinations for the ratio of extrinsic to intrinsic stacking fault energy in fcc solid solutions are examined. Some of these arise from incomplete analyses which can yield only approxi?nate values for the ratio. Reliable results, on the other hand, obtained using extrinsic-intrinsic fault pairs, show that the extrinsic and intrinsic fault energies are essentially equal in several materials. There is some reason to believe that this finding is of general applicability to fcc elements and alloys. A wide range of values has been obtained for the relative magnitudes of the extrinsic and intrinsic stacking fault energies (yext and yint, respectively) in recently published studies in a variety of materials. In contrast, Hirth and Lothe' using a central force model have shown that out to tenth nearest-neighbor interactions the perturbation in energy caused by both types of fault is the same. Although the model used is not completely valid in metals, there is nevertheless some indication that marked variations of yext/nnt should not be observed from one material to another. In early work in Cu-A1, Cu-Ge, Ni-Co, and stainless steel all the deformation faults observed in the electron microscope were found to be intrinsic in nature, which led to an attitude that the extrinsic fault energy must be considerably greater than the intrinsic. Extrinsic faulting arising from deformation has, however, more recently been directly observed in Au-4.8 at. pct n;~ Ag-6 at. pct Sn and Ag-8 at. pct sn; Ag-7.5 at. pct In and Ag-11.8 at. pct 1n;"' pure silwer and Ag-0.5 at. pct ~n;' and Cu-22 at. pct Zn, Cu-30 at. pct Zn, and Cu-7.5 at. pct ~1.l' Multilayer loops containing extrinsic faulting have also been observed in quenched aluminum." While peak asymmetries in X-ray faulting probability studies were generally attributed to the presence of twins,Lelel2 has recently reinterpreted earlier X-ray data in Ag-Sb alloysU in terms of the presence of extrinsic faulting. The determinations of yeXt/yint made from the above studies are shown in Table I, with a brief description of the techniques employed. A number of the methods utilized are deficient in one or more respects, and the reliability of the values listed will be discussed. ~ele'~ recognizes that his approximate determinations of yext/yint assumes equal numbers of extrin-sically and intrinsically faulted dislocations. It is well-known, however, that such an assumption is not at all justified since extrinsic faulting has but rarely been observed in samples studied in the electron microscope. The only conclusion that should be drawn from the X-ray results at present is that the total intrinsic scattering cross section (i.e., the product of the width of the intrinsically faulted dislocations with their density) is approximately ten times greater than for extrinsic faulting in these particular samples. An important point is that the relative magnitudes of the energies cannot be inferred from results of this type, unless the intrinsic and extrinsic faults form with equal ease. One must recognize that, although a formation barrier may restrict the amount of extrinsic faulting which occurs, this in no way implies that the extrinsic and intrinsic energies should be different. It is unlikely that a worthwhile estimate of the relative densities of extrinsically and intrinsically faulted dislocations can be made at the high deformations present in X-ray samples. ~oretto,'~ from a statistical argument applied to the nonobservation of extrinsically faulted tetrahedra out of a large sample, concluded that yeXt/yint could not be less than -4.5. However, the present author feels that a high-energy formation barrier as just supposed also explains this finding satisfactorily and that no conclusion can possibly be drawn concerning the actual extrinsic stacking fault energy. The same argument also serves to explain the fact that extrinsic faulting has been relatively little observed in the electron microscope. Extrinsic-intrinsic node pairs and isolated extrinsic nodes were first reported by Loretto~ and subsequently by Ives and Ruff,' Gallaher,' and Gallagher and Wash-burn.' Ives and Ruff' found a wide spread in the ratio of extrinsically to intrinsically faulted area in the node pairs they observed, and drew the very tentative conclusion that yeXt/yint 2 2. They recognized that a straightforward comparison of the size of the faulted areas could provide no more than a qualitative result without a theoretical analysis of the dislocation geometry associated with extrinsic faulting. A theoretical

Jan 1, 1969

By George B. Clark

Many basic engineering principles of all four phases of mining operations, namely, prospecting, exploration, development, and exploitation, can be analyzed better in terms of quantitative geology. Geological data from both field and laboratory will also complement scientific methods now being developed. THE geological data emphasized so successfully in prospecting for new deposits, that is, structural controls, strength of solutions, and type of mineralization, are basically those required for successful exploitation. In the mining of newly discovered deposits the most economical methods should be employed as early as possible to keep the overall cost per unit produced at a minimum and to permit maximum extraction of valuable minerals. A crucial question is: How can geological data be translated into useful quantitative results which will aid in achieving this end? H. E. McKinistry' has suggested that a solution may be reached in one of two ways: 1—the usual approach, use of judgment based on experience; or 2—mathematical calculations and tests on models, both subject to certain limitations. He also suggests that in addition to better use of geology more case data and theoretical data are needed on which to base sound judgment. Further research, therefore, is necessary. Perhaps in this field the emphasis should be on more specialization in mining methods and ground movement by men with thorough training in physics, engineering, geology, and underground mining. These specialists would be equipped to point out the most economical and scientific methods of exploitation. Selection of a stoping method is governed by the amount and type of support a deposit will require in the process of being mined, or by the possibility of employing the structure of the deposit to advantage in mining the ore by a caving method. In addition to these factors there are others which almost invariably influence the choice of an economical method of mining:' 1—strength of ore and wall rocks; 2—shape, horizontal area, volume, and regularity of the boundaries of the orebody, and thickness, dip and/or pitch of the deposit and individual ore shoots; 3—grade, distribution of minerals, and continuity of the ore within the boundaries of the deposit; 4—depth below surface and nature of the capping or overburden: and 5—position of the de- posit relative to surface improvements, drainage, and other mine openings. In the final analysis it is usually necessary to disregard the less important of these factors to satisfy the requirements of the more important. Because of the variation of geological conditions throughout and surrounding the deposit, no mining method will be everywhere ideally applicable to the conditions encountered in one ore deposit. The immediate problem is to interpret the above physical characteristics of deposits in terms of geological characteristics. Very few quantitative geological data are available on the factors related to a choice of mining methods. However, there are many descriptive data in mining and geological literature which collectively show how important an effect details of geology have upon all phases of mining operations. The following categories of basic mining methods were investigated to establish the geological factors that have affected their successful application: 1— open stopes with pillars; 2—sublevel stoping; 3— shrinkage stoping; 4—cut-and-fill stoping; 5— square-set mining; 6—top slicing and sublevel caving; and 7—block caving. It should be noted that the first five of these methods are listed in the order of increasing support requirements. Mines were selected as examples only where geological descriptions were complete enough to warrant their use. A study of the geological factors involved in mining operations led to a choice of the following classifications, employed in Table I: 1—structural type of orebody; 2—dimensions (geometry); 3— country rock (type); 4—faulting, folding, and fracturing; 5—alteration of ore and rock; 6—type of mineralization; and 7—geological factors determining mining method (summary). Of these factors only one yielded results that can be defined from available data in a quantitative manner, i.e., dimensions of the deposit. These are the most reliable guides that can be used in selection of suitable mining methods. They are, in general, the properties of geologic structure most difficult to evaluate by studies of models, pho-toelastic studies, and other laboratory methods, all of which are at present more limited in their applications than the geologic method. Application of geology has proved a reliable guide in other phases

Jan 1, 1955

By R. J. Wagner, F. F. Craig, H. G. Riley, J. D. Griffith

Peripheral water injection has been underway in the Sholem Alechem Fault Block "A" Unit, Stephens County, Okla., since 1955. In the engineering planning of the flood, it was recognized that maintenance of pressure in the large, dry gas caps was vitally necessary to prevent the loss of an estimated 27 million bbl of oil through saturation of the gas caps by the oil banks moving updip on the peripheral flood pattern. The development of an abundant, low-cost water supply and the rising cost of makeup-gas purchases indicated that gas-cap control by water injection was desirable from an economic standpoint, provided an eflective water barrier could be placed without premature water breakthrough into downdip oil producers. A laboratory model scaled to the existing reservoir conditions was comtructed to evaluate the feasibility of gas-cap water injection. Model studies indicated that (I) water injected at the edge of the gar-oil contact would form a continuous barrier between the oil and gas zones, and (2) water would advance uniformly downdip without segregation due to gravity effects provided a specified, minimum water-injection rate was maintained. The model test results also indicated that it was not necessary to fill the gas cap completely with water. Water injection at the edge of one of the gas caps was initiated in March, 1958, to field test gas-cap water injection. Water breakthrough occurred at a downstruc-ture producing well in April, 1959, after approximately 2.5 million bbl of water had been injected into the gas cap. This was the volume calculated to be required to form the barrier between the oil zone and gas cap. This performance indicates that prevention of oil encroachment into dry gas caps in a peripheral water flood by water injection at the gas-oil contact appears practical and that the model studies provided a valid prediction of field performance. INTRODUCTION The Sholem Alechem Fault Block "A" Sims Sand Unit was one of the fist major waterflood projects in Oklahoma to utilize a peripheral injection pattern. Design of control measures to minimize oil encroachment into the large crestal gas caps was one of the greatest single problems during engineering planning of this flood. Engineering studies indicated that saturation of the gas caps with oil displaced by the peripheral water flood could result in a loss of about 27 million bbl of oil, or over one-half the estimated waterflood recovery. This estimate was based on a residual oil saturation after water flooding of 35 per cent pore volume, compared to the negligible oil saturation initially in the gas caps. The Sholem Alechem Springer field, located in Stephens County, Okla., is an elongated anticline with structural dips varying from 400 to 1,000 ft/mile. The structure contains numerous faults, some of which are sealing. The portion of the field considered in this paper is Fault Block "A", which is the largest of the five major fault segments in the field. A map of the unit is shown on Fig. 1. The unit is bounded on the east and west by major sealing faults, on the north by a water-oil contact and to the south by a deterioration of sand development. Two domes, each having gas caps, exist in the unit and are separated by a north-south fault as shown in Fig. 1. The sands being flooded are the Sims sand members of the Springer series of early Pennsylvanian age. The Sims sands average over 100 ft in thickness in Fault Block "A" and have a porosity of approximately 19 per cent. Core permeabilities average 160 md, with interstitial water saturation of about 23 per cent pore volume. Three different zones can be correlated over most of the area. However, they are commingled in most of the producing wells. The two upper zones, designated as First and Second Sims, are the most important. Both the First and Second Sims have gas caps in the east dome, while only the First Sims has a gas cap in the west dome. These gas caps, whose limits are also shown on Fig. 1, initially occupied nearly 11 per cent of the total reservoir volume. The major concern of this paper is the control of the two gas caps in the First Sims sand. Fig. 2 is a cross section, to scale, across the east dome of this formation. Notable features are the relatively shallow dip, the deterioration of the First Sims sand on the south side of the gas cap and the water-oil contact on the northern edge. The formation dip at the gas-oil contact in this cross section is approximately 5".

By William Paxton Hewitt

The San Carlos lead deposit in northeast Chihuahua yielded approximately one million tons of galena ore from a blanket-like deposit. Countryrock, composed of Cretaceous limestones and calcareous shales as old as late Albian-early Aptian, and an underlying undated quartzite series, has been warped into a northwest trending anticline and has been invaded by a light-colored holocrystalline igneous rock. Magnetite and contact metamorphic minerals heterogeneously mixed with variable amounts of pyrite, sphalerite and galena, are concentrated along the anticlinal axis where they replaced magnesia-rich argillaceous sediments above the quartzite contact. Magnetite and associated silicates were deposited under near-contact conditions. Following a period of post-magnetite shattering, pyrite, sphalerite and galena were introduced at lower temperatures. Galena and associated dolomite or magnesite, the final phase of mineralization, are concentrated at the top of the deposit near the anticlinal crest and extend upward into isoclinally folded dolomitic argillites. INTRODUCTION AND ACKNOWLEDGEMENTS The stoped outlines of the San Carlos Mine are a pattern for a stratiform blanket-like deposit. But the close association of mineralization with an anticlinal axis, an observed relation between high grade galena mineralization and the apices of isoclinal folds, and the petrographic story of mineralization introduced into shattered areas make the deposit an example of structural control of ore de-

Jan 1, 1970

By J. S. Marsh

OPPORTUNITY to pay tribute to the memory of Professor Henry Marion Howe is a strenuous assignment as well as an honor. Upon recalling Howe lecturers and lectures of the past 25 years, glancing over the list of those earlier, and rereading Howe's books, I arrive at several conclusions: 1—Many lecturers either worked under or knew Professor Howe. 2—It is virtually impossible to pick a subject on which Professor Howe did not touch. 3—There is precedent for a technical paper based upon pursuit of a single subject. 4—There have been listening lectures and reading lectures. There is solid comfort only in 2: the subject field is wide open. I did not know, nor even ever saw, Professor Howe, so can supply no fitting reminiscence. As a college student I was dimly aware that he counted among the giants. Fuller appreciation of his stature came with reading his books and papers, growing acquaintance with some of his associates, and the intrinsic dignity of the climax of the Annual Meeting, beginning at four o'clock of a Thursday afternoon in the auditorium of the Engineering Societies Building in New York. As for producing the technical paper sort of thing, it is my lot to have reached an age and assignment such that to do so would be to filch information from those who did the work and whose story is theirs to tell; for this I have no enthusiasm. As for the final conclusion, Professor Howe was one of the chosen few so highly expert at expository writing that he could produce a lecture or paper that reads as though it would also have listened well. One of his tricks was the free use of words not ordinarily part of the technical vocabulary, provided that such words were likely to communicate most precisely what he had in mind. How wonderful it would be for all who must read reports by the ton if ability at exposition could be taught with the effectiveness open, say to, differential calculus! Perhaps Professor Howe should be required college reading even if for no other reason than to prove that technical writing need be neither dull nor diffuse. My assignment is clearly still strenuous. Another point to consider is the fact that metallurgy is now so tremendously diversified that hope of finding a topic of universal appeal is negligible, even if one were competent enough to be permitted free choice. That which follows is, therefore, a compromise composed of necessity and of the obligation to attempt to avoid boring to slumber those of you who are not especially interested in the general subject chosen. The Iron and Steel Div. is now essentially a process metallurgy division, heavily concerned with the smelting of iron and the making of steel. The American Iron and Steel Inst. figure for present steel capacity of this country is 125,828,310 net tons; how this is divided among processes is indicated by the production totals for 1953, shown in Table I. The glamor girls and boys make the front page and so it is with steelmaking processes. If there is an Antarctic Daily Bugle, it undoubtedly has carried stories of revolutionary development, such as oxygen processes and vacuum melting, and stories of the incomparably rosy destiny of electric arc melting. All such certainly have their place and their future; meanwhile, it is the sturdy and old reliable open hearth that accounts for the bulk of production reported back on the financial page, and it is the old reliable that is most likely to continue to account for the bulk for some perfectly sound raw material, technologic, and economic reasons. This, plus the fact that next year marks a centennial (for it was in 1856 that Frederick and William Siemens conceived the regenerative open hearth), is reason enough to talk about open hearth furnaces, but is not the real one. The real reason is that in some years of association with open hearths, I have accumulated—in addition to a genuine liking and respect for them—certain odds and ends of fact and fancy that this lecture provides a unique chance

Jan 1, 1956

By AIME AIME

A discussion of the Papers by Prof. H. Hubert, Liege, Belgium ; Mr. Tom Westgarth, Middlesbrough, England ; and Mr. K. Reinhardt, Dortmund, Germany, presented at the London Meeting, July, 1906, and printed in Bi-Monthly Bulletin, No. 12, November, 1906; pp. 910 to 930, 971 to 987, 1037 to 1163. MR. ADOLPH GREINER, Seraing, Belgium :-I have nothing special to add to Professor Hubert's paper except to say that there are some little things that it would be well to have cor-rected when the paper comes to be published. In dealing with the thermal efficiency of the engine, you will find that the 29.84 per cent was a very high one. Professor Hubert has forgotten those engines built under the Cockerill type, but he has referred to them in Appendix II. At our works at Cockerill we have built 63 engines, giving 63,000 h.p., and the other companies who have received licenses have built 113 engines, making 103,000 h.p., and aggregating 176 engines and 166,000 h.p. Eight years ago I had the pleasure of giving to the Institute the results obtained up to that time. Since then a good many engines have been constructed. In 1898 I thought a blast-furnace producing 100 tons of pig iron would allow 3,000 h.p. Professor Witz and Professor Hubert show that with the same production of pig the new engines take 3,800 h.p. out of the gas. At present at Cockerill we make 700 to 800 tons of pig iron per day, and we hope to have 26,000 h.p; in a few years. At present we have only half of that in gas-engines, but we hope to have in five or six years all the gas out of these furnaces to the number of 25,000 or 26,000 h.p. MR. Tom WESTGARTH, Middlesbrough, England:-My contribution is not a paper in the ordinary sense of the word, because I am sure you will agree with me that what I have written is only supplementary to the other two papers. The notes are schedules of the larger-size gas-engines built by the engine-makers, of 500 h.p. and upwards. If you look at the schedules you will find that in England gas-engines have be-

Jan 1, 1907

By AIME AIME

SCRIPTURE, statistics and imagination all were drawn upon by the speakers who acclaimed Daniel C. Jackling as recipient of the William Lawrence Saunders Gold Medal for 1930. The award was made at a special dinner at the Ritz-Carlton, in New York, on Oct. 31. Lafayette Hanchett, old friend and associate, said that if it were his task to compress the life story of Daniel Jackling into a single sentence, he could find noth¬ing so appropriate as these words from the 22nd Chapter of Proverbs, "See'st thou a man diligent in his business, he shall stand before Kings." Mr. Jackling's diligence, according to the speaker, his love for his task, have been outstanding in his career. W. S. Boyd, now ranking official in the Jackling organization, cited amazing statistics as to the quantity of copper supplied to industry by the four "porphyry". coppers that are under Mr. Jackling's immediate direc¬tion, as well as by those that, in a sense, owe their existence to the pioneer work at Utah Copper. In the aggregate- 16,000,000,000 lb. of copper having an approximate value of $2,700,000,000 have been produced from disseminated ores since 1905; and of this total 42 per cent came from Utah and the Nevada group. Newcomb Carlton, president of the Western Union Telegraph Co., long an admirer of Mr. Jackling, adroitly drew a picture of a similar occasion in some 'foreign country. He imagined Mr. Jackling being raised to the peerage and whimsically addressed him as Sir Daniel, the Right Honorable Earl of Bingham!

Jan 1, 1930

By Orlando E. Romig

As metals and alloys are composed of an aggregate of allotriomorphic crystals or grains, each possessing an individual orientation, the physical characteristics of a metal or an alloy are closely related to the properties of the individual crystals. The preparation and study of single metallic crystals are, therefore, matters of considerable importance. The advent of the X-ray spectrograph as a valuable metallurgical tool has magnified the importance of this subject, because the interpretation of some X-ray spectrographs is difficult unless single crystals are used in these studies. Previous Work The first paper, as far as the writer knows, on the behavior or preparation of single crystals of metals is by Baker.' He describes the behavior of extruded wires of sodium and potassium. These wires, when pulled in tension, instead of showing the usual conical fracture common to most metals, had a chisel-shaped fracture when they were broken. I and 11, Fig. 1, have a similar fracture. Baker checked his results by preparing single crystal wires from molten sodium and potassium and observing their properties. He pre- pared the wires by filling glass tubes, under oil, with the molten metal. The surfaces of the strained wires showed slip bands of remarkable clearness of which photographs are shown in his paper. He concluded that these wires were single crystals and "that the portions of the metal brought into play are cubes. Such cubes, when placed so that a plane through two opposite edges was parallel to the axis of the wire, would allow of lateral contraction by faces gliding over one another in one direction only and not in the direction at right angles."

Jan 1, 1927

By H. Leslie Bullock

From aluminum to zirconium, the quantitative preponderance of quartz as a gangue material is well recognized. lf this material is to be efficiently removed, its variations must be understood. Variations with temperature are especially important. Too little attention has been given to the thermal polarization of quartz. Under closely controlled conditions, electrostatic upgrading is very reliable. For efficient separation, contact charges must be fostered and charges due to radiation, surface coatings, or thermal polarization avoided. This paper lists thermal transition points of quartz and shows their effect on actual separations. Simple separation tests with all factors except temperature held constant are recommended for determining transition points. With silica making up more than 27% of the earth's crust, its oxides comprising more than 59% of all igneous rocks, and quartz accounting for most of the main free oxides, the mining engineer is in constant contact with quartz, which may occur as a valuable mineral to be purified or, far more frequently, as a gangue material to be removed as completely and economically as possible. As a means of effecting such purification or removal, dry beneficiation is becoming more and more desirable owing to local water scarcities, wet waste disposal problems, or freezing conditions. One method that has been gaining particularly rapid acceptance is electrostatic beneficiation, or the separation of dry free-flowing materials by means of opposite surface charges, differences in potential, or differences in conductivity. Electrostatic beneficiation dates back to the 1870's, but only in recent years have newly developed methods and apparatus and a growing knowledge of solid-state physics widened the field for its economical application. Because the term "electrostatic beneficiation" has been rather loosely used in the literature, it has come to include both electrostatic and electrodynamic procedures. Attracting type separators, however, in which oper- ation is based on differences of surface charge or potential, are truly electrostatic, because the separation occurs in a substantially static field set up between oppositely charged surfaces. Separations with this type of equipment may occur at potentials as low as 1000 v and seldom require potentials as high as 30,000 v. In the new contact charge dielectric separators1 the variation in charge is produced by continuous contact and separation of the particles in the moving feed stream and these charges are fostered by the use of non-conducting support and feed surfaces and by handling the feed in the form of streams of appreciable depth. This favors uniformity of feed and allows higher production rates. The distinctive surface charge differences are set up on the separation of the particles according to Coehn's Law,2 which states that equal and opposite charges are generated on the separation of any two materials in contact and that the substance having the highest dielectric constant will be positively charged. The basic contact charge concept is reliable, but all electrical charges are transient and modified by the electrical conditions of the surroundings. Pyro-electric, photoelectric and radiant effects may modify or totally destroy the contact charges necessary for efficient separation, or contact with conducting surfaces may neutralize them. Such hostile conditions must be carefully guarded against, since they have led to many costly failures in the past. The most consistent difference in surface charges to insure good separation is produced by repeated uniform contact and separation of particles in the moving stream. The thickness of the feed stream possible with this method reduces the effect of contact with the supporting surfaces, but as some contact is inevitable, the best results may be assured by having the dielectric constants of the supporting surfaces between the dielectric constants of the substances to be separated. In general, the hard smooth surface of quartz makes it an ideal substance for electrostatic separation from most minerals. For instance, with calcite, starting with a feed containing 1.9% acid insolubles, one can produce a concentrate containing 0.30% acid insolubles with a tailings containing 21.7% acid insolubles and a yield of 92.8%. The color can be held at 92 or above and the tint at 1.7 or lower. Working with specularite iron ore, laboratory work has given a concentrate of 68.8% Fe., with an iron unit recovery of 96.7%. Excellent results are also in pros-

Jan 1, 1969

By H. A. Pearse

NORMALLY, the Britannia ore mixture contains chalcopyrite and pyrite as the chief sulfide minerals, together with minor amounts of gold and silver and a low zinc content. Reduction is accomplished by jaw crushers underground, followed at the concentrating plant by Symons cone crushers, rolls, and ball mills. The standard flotation practice, evolved during several years of experimentation, provided for bulk flotation of the two sulfides, after primary grinding to only approximately 35 mesh, followed by regrinding of the bulk concentrate, with subsequent separation of the chalcopyrite and pyrite to make a marketable concentrate of each mineral. This so-called standard milling practice has previously been described in detail in U. S. Bureau of Mines Information Circular 6619. A modification will he discussed here. In the face of a constantly increasing world surplus of copper and a steadily falling price during 1930 and 1931, it was obviously undesirable to continue unprofitable production of large quantities of this metal. On the other hand, company officials were

Jan 1, 1934

By O. D. Gonzalez, R. A. Oriani

The migration of hydrogen and of deuterium dissolved in a iron and in nickel induced by an applied electrical potential has been measured over a range of temperature. In all cases the intevstitial solute migrates to the cathode. The deduced charges of transport are positive, independent of or slightly dependent on temperature, and markedly larger for the beavier mass. These results are interpreted as showing predominating momenlum transfer between electron holes and the acticated complex of the elementary diffusion act. THE migration of components of a metallic system under the action of an applied electrical potential is called electromigration or electratransport. This phenomenon has been known since 1861 and is becoming of increasing interest to metal scientists because of the opportunity it offers to explore the connections between mass transport and electron transport. Until recently, reliable data have been very scarce because of the difficulties inherent in the measurements. In addition, theoretical understanding has been either nonexistent or rudimentary and at present this situation is only moderately improved. Whereas the prevalent notion had been (and is still widely held) that electromigration directly reflects the state of ionization of a component in its equilibrium state in the metal, it is now becoming clear that the major, if not the sole, factor is the momentum transfer between the charge carriers, themselves in motion because of the applied field, and the metallic components in their activated state. It becomes important therefore to obtain reliable data over a range of temperature on electrornigration in systems where only one component moves, that is, either in pure metals (vacancy motion) or in interstitial solid solutions. Our choice of systems was dictated by our measurements' of the Soret effect in solid solutions of hydrogen and deuterium in iron and nickel. Indeed, the main reason for making measurements on electromigration at all is that we suspected a mechanistic connection between thermal diffusion and electromigration. In our former paper' we proposed that what is common to both phenomena is the momentum transfer between the charge carriers in the metal and the atom as it jumps from one equilibrium position to another. In Soret diffusion, however, there is in addition the dissipation of the energy of the jumping atom via pho-nons. We have since found that similar ideas for this interconnection have been developed by Fiks.2 In the present paper we will discuss in more detail our understanding of the mechanism of electromigration itself, but we turn first to a presentation of the experiments and results. EXPERIMENTS AND RESULTS Let us consider a metallic system in which only one component, m , can diffuse at the temperature in question, and to which are applied simultaneously an electrical potential gradient, grad cp, and a chemical potential gradient, grad p,. One may write3 for the material flux Jm and the electronic charge flux Je by applying the condition, grad = 0, to Eq. [I] and evaluating grad(um/T) for the isothermal case and for activity coefficient independent of composition over the relevant composition range. ere, c is the concentration and D the diffusivity of the mobile component. The experimental technique that we have used to measure Z* for the isotopes of hydrogen individually dissolved in each of two transition metals has been developed from a method used by Wagner and Heller.4 (A somewhat similar method was also used by Herold.5) A wire or thin rod of the metal under study connects two volumes of gaseous hydrogen at identical pressures; hence grad um = 0. A direct current is made to pass through the specimen, serving to maintain the specimen at the desired temperature and also to produce the electromigration of the hydrogen dissolved in the metal in equilibrium with the gaseous hydrogen. Under these conditions, the flux of hydrogen from one volume to the other is given, from Eq. [I] for grad( um/T) =0by

Jan 1, 1968

By J. E. Walstrom

While intensive research continues to promote a more complete understanding of the potential and resistivity measurements that comprise the electric log, it is believed that consideration should also be given to translating these numerous and often widely separated findings into a coordinated and readable body of fundamental facts designed specifically for the petroleum engineer and geologist. Although provision is made through publication for a ready exchange of new theoretical concepts. it is also desirable to provide reviews and appraisals of the more established techniques and methods from the operating standpoint so that an economic and practical application may be realized concurrently with the theoretical progress. With these basic premises as a guide the author reviews the presnt state of electric log interpretation. The paper is directed not so much to the logging or research specialist as to the petroleum engineer and geologist to whom the electric log is only one of the many tools which he employs. Frequently, these persons do not have the time to follow in detail the many specialized contributions that appear and, as a consequence. are not in a position to place these contributions in proper relation to each other, or to the art as a whole. The paper reviews the basic steps in making quantitative determinations from the electric log of the amount of oil or gas present in subsurface formations and also discusses the degree of reliability of these determinations under various conditions. The paper also indicates the trend of future developments in electric logging systems and methods of interpretation. INTRODUCTION The electric log has been used about 20 years as a means for studying the formations penetrated by a well bore. The first half of this period is characterized by the development of suitable logging techniques and equipment. Although progress in this direction is continuing at a satisfactory rate, the last ten years are characterized more by an increasing interest in methods of electric log interpretation. During this period, a large number of fundamental papers have been published, expounding various logging techniques and particular phases of the interpretation problem. Many of these papers represent important contributions, and a few are classic. This paper is an effort to outline as concisely as possible and in simple terms the main course of progress in electric log interpretation. More specifically, it is the purpose of the paper to review the necessary elements and basic steps used in making quantitative determinations of water saturation from the electric log; and to point out the degree of reliability of these determinations under different conditions. It is strongly advised that the operating staffs of the drilling and exploration departments of oil companies cooperate wholeheartedly with both the electric logging service companies and research organizations in the testing and development of new logging systems and interpretation methods. One purpose of the paper is. however, to indicate the degree of caution which must be exercised in placing confidence in new techniques and interpretation methods that have not been thoroughly tested in the field. It is entirely possible to be cooperative in trying new methods and yet reluctant to believe in the results until the methods are firmly established. It is important to define the meaning of quantitative electric log interpretation. In the most general sense, an interpretation of the log has been made when the electrical characteristics of the formations, as portrayed on the log, have been translated into terms describing the formation geometry, rock type, or any other physical characteristics of the formations. The determination that the top of a sand is at a certain depth is an interpretation of the log. Structural determinations made by correlating electric logs from a given area are also interpretations of the logs. The term quantitative interpretation, however, will be used in this paper in the restricted sense to indicate the determination of the water saturation of a formation. This determination defines the fluid content of an oil and gas productive formation only if the porosity is known, and it assumes that the remainder of the pore space contains hydrocarbons. This assumption is believed to be true for most oil and gas productive formations. The quantitative electric log interpretation may he said to be a determination of the fluid content only to the extent which the water saturation, under the conditions given above. defines it. THE BASIC STEPS The fundamental steps in calculating water saturation from the electric log are: 1. Determination of the true resistivity of the formations from the apparent resistivities as recorded on the electric log.

Jan 1, 1952

By D. B. Robinson, C. A. Macrygeorgos, G. W. Govier

Experimental data have been obtained on the volurrletric behavior of ternary mixtures of methane, hydrogen sulfide and carbon dioxide at temperalures of 40°, 100" and 160°F up to pressures of 3,000 psia. The results indicate that the compressibility factors for this system do not agree with compressibility factors for sweet natural gases at the same pseudo-reduced conditions. The deviation increases as the temperature and methane content decrease. Discrepancies of up to 35 per cent were observed. A careful analysis has been made of the existing pUrblished data on compressibility factors for binary systems containing light hydrocnrbons and hydrogen sulfide or carbon dioxide. It has been found that the deviation of actual from predicted compressibility factors for methane-acid gas mixtures is a function of the methane content and the pseudo-critical properties,.v of the mixture. The ratio between actual compressibility factors for methane-acid gas mixtures and compressibility factors for sweet natrlral gases at the same pseudo-reduced conditions has been currelated over a range of pP,, from 0 to at least 7 arid a range of pT, from about 1.15 to at 1east 2 0 with an error not exceeding 3 per cent and over most of the range within I per cent. The validity of the correlation for mixtures containing appreciable hearvier hydrocorbons has not been fully established, but it is shown to be preferable than the use of a corretation based only on hydrocarbons. INTRODUCTION Although a relatively accurate method for predicting compressibility factors of pure materials is provided by charts based on reduced properties and the assumption that the compressibility factor is a unique function of T P and z the determination of the correct values of compressibility factors for gas mixtures is somewhat difficult. Two general methods of dealing with gaseous mixtures have been proposed. The first assumes a direct or modified additivity of certain properties of the mixture in terms of the properties of the individual components. Examples of this method are based on the familiar laws of Dalton and Amagat. The second method averages the constants of an equation of state applicable to the pure components. Both of these methods are of limited value in engineering calculations because the first usually provides reliable answers only over narrow ranges of pressure and temperature and the second is cumbersome to handle. In petroleum engineering practice accurate estimations of the volumetric behavior of natural gases arc frequently required. To fulfill this need, several generalized compressibility charts have been developed.' ' Of these, the one prepared by Standing, el al is widely used at present. In the construction of charts of this type a third method for dealing with mixtures has been followed. It is based on correlation of pseudo-critical properties as outlined by Kay and calculated from the critical properties of the individual components in a mixture. Although these charts provide relatively accurate information on the compressibility of dry or wet sweet natural gases, they are less reliable when used for gases containing high concentrations of hydrogen sulfide or carbon dioxide or both. Thus, an experimental program, although time consuming, is the best means now available for the determination of the volumetric behavior of sour or acid gas mixtures. An increased interest in the behavior of these gas mixtures, particularly in connection with some of the fields in Western Canada where the acid gas concentration of the reservoirs may be as high as 55 per cent and where hydrogen sulfide alone may be as high as 36 per cent, provided the incentive for this study. It was the purpose of the investigation to determine the volumetric behavior of selected mixtures of methane, hydrogen sulfide and carbon dioxide over a range of temperature from 40" to 160°F and at pressures up to 3,000 psi. EXPERIMENTAL METHOD The apparatus used in this investigation was basically the same as that described by Lorenzo.'" The amount of each pure component used in preparing the gas mixtures was measured over mercury in a glass-windowed pressure vessel. The pure components were then transferred individually in the desired amounts to a second glass-windowed pressure vessel where the volumetric behavior of the mixture was determined. Volume was varied by mercury injection or withdrawal. The capacity of the cell was about 125 cc. Temperatures in the cells were measured with copper-constantan thermocouples and a Leeds Northrup semi-

By Lawrence Addicks

T HIS has been a most momentous year in the annals of the Institute. We have been in the midst of a situation which, were it not for the convulsions of social unrest with which life is surrounded on every side, would have attracted the attention of the world at large. I do not refer to the desperate campaign for new members. That has gone on much as usual except that, this being leap year, the annual proposal to the M. & M. Society has been omitted. Nor do I refer to the desperate situation which we found in other directions, the spread of Bolshevism, the burning of the Engineers' Club, the fact that the selling of copper appears to have become one of the lost arts. No, I speak of the great question which has to be. settled once and for all, as to whether this great Institute should adopt simplified spelling. The whole trouble started in the ranks of the California Hysterical Society. It appears, while most of the San Francisco members can read and write, several of them cannot spell. It also appears that the Secretary, in editing the Transactions, has perhaps made just a little bit too much of a point of employing the correct Stoughton idiom. At any rate, the rebels filed an amendment to the constitution, and the stage was set for civil war, with perhaps more stress on war than on civil.

Jan 1, 1920

By AIME AIME

T HE Executive Board of the American Engineering Council held its fourth meeting at St. Louis on the first anniversary of the organizing conference which met in Washington on June 3,1920. Representatives of a number of the leading engineering organizations in the vicinity of St. Louis were present by invitation. The members of the Executive Board were guests of the Associated Engineering Societies of St. Louis. They were given a delightful ride about the city and were entertained at the Glen Echo Country Club at dinner. The special committee that had been appointed to draft resolutions to Mr. Hoover submitted the following, which were adopted : WHEREAS, our President, Herbert Hoover, has been appointed Secretary of Commerce in the Cabinet of the President of the United States, and WHEREAS, in consequence of his acceptance of this high public office, he has deemed it necessary to tender his resignation as President of The Federated American Engineering Societies.

Jan 1, 1921