Search Documents

By T. Price, H. A. Holl, A. P. Greenough, A

UdIN, Shaler, and ulff' first used wires for the determination of the surface energy of a solid metal. A gage length was marked by tying knots in the wires, which were then suspended in a cylinder of the same metal, heated in an inert atmosphere for the appropriate time, cooled to room temperature, and finally removed from the furnace so that the lengths of the wires could be measured. With iron wires, difficulties associated with deformation during the phase changeszp3 made it necessary to measure the gage lengths at the tem-

Jan 1, 1964

By H. C. Fiedler

The development of cube-on-edge secondary re crystallization texture in Si-Fe strip depends upon the ability of inclusions, such as manganese sulfide, to restrain nomal grain gvowth. The ability of inclusions to perform this function is shown to depend upon their size and distribution. The desired uniform dispersion of many small inclusions is obtained by controlling the cooling rate from above the solution tempmature of the inclusions or, alternatively, by drastic 'quenching from above the solution temperature followed by heat treating at a lower temperature. The development of the cube-on-edge secondary recrystallization texture in Si-Fe strip depends upon both establishing the proper primary recrystallization texture and having inclusions to restrain normal grain growth. It has been suggested that the first requirement is met with a texture which, though weak, is near (110)[001]. A mechanism for secondary recrystallization originally proposed by ielsen' is consistent with the presence of this primary texture. It is visualized that a secondary grain appears where two adjacent grains happen to be sufficiently similar in orientation to be capable of behaving as a single large grain. This pair of grains will grow at the expense of its smaller neighbors as a consequence of its having lower grain boundary free energy. Other explanations of the origin of the secondary recrystallization texture have been offered,' and it can be concluded that the mechanism is not fully understood. Nevertheless, it is apparent that operationally the necessary primary recrystallization texture is obtained simply by interposing an anneal during the cold reduction to final gage. The role of inclusions in the development of the secondary recrystallization texture has been demonstrated by May and Turnbull4 in a comparison of a high-purity heat and a heat containing manganese sulfide. They showed that the driving force for secondary recrystallization is inversely proportional to the diameter of the matrix grains and that the function of the inclusions is to maintain a small matrix grain size. Other inclusions, such as various sul- fides,')' silicon nitride,8 and vanadium nitride,' titanium carbide,'' and vanadium carbide," have been shown to be effective in promoting secondary recrystallization to the cube-on-edge texture. There is also evidence that silica inclusions in Si-Fe strip made by powder-metallurgy techniques perform this function.' This report is concerned with the second of the two requirements for secondary recrystallization, namely the importance of the metallurgical control of the size and therefore number of inclusions. While the concepts involved are simple, they are fundamental to the making of this material. EXPERIMENTAL PROCEDURE A heat containing 3.27 pct Si, 0.026 pct S, 0.06 pct Mn, and 0.004 pct C was made in an air induction furnace from electrolytic iron, 98 pct ferro-silicon, electrolytic manganese, and iron sulfide. The heat was divided between graphite and baked-sand molds with a cavity 2-5/8 by 5 in. and with walls 2-3/4 in. thick. Slabs, 1 in. thick and 2-5/8 by 5 in., were cut from the ingots and hot-rolled either in the as-cast condition or after one of the heat treatments described later. After pickling, the 80- to 100-mil-thick hot-rolled band was, unless otherwise noted, heat-treated for 5 min at 900°C before being cold-rolled to 25 mils. After a heat treatment of 1 to 3 min at 860°C, the strip was cold-rolled to 12 mils, the final thickness. The percent cube-on-edge texture was determined by dividing the maximum torque as averaged from four samples by the maximum torque of a 3-1/4 pct Si-Fe single crystal having the (110) plane in the plane of the sample. The torque measurements were made in a field of 1000 oe on 1-in.-diam disks. RESULTS AND DISCUSSION The importance of the thermal history of the ingot is evident in Fig. 1 from the appearance of strips heat-treated in a temperature gradient. The sample

Jan 1, 1964

By C. W. Kovach, A. Moskowitz

Studies were undertaken to investigate the effects of manganese content on the machinability and other Properties of a free machining martensitic stainless steel (AISI Type 416). Machinability was found to be significantly improved in steels of high manganese content, and a direct relationship was obtained between machinability and steel Mn:S ratio. As the manganese content of the steel increases, the sulfide Phase present changes from CrS to (FeMn)Cr2S4 to (MnFeCr)S, and finally to MnS. The average sulfide inclusion hardness decreases through the same range of increasing manganese content. The mechanism for machinability improvement is discussed in terms of a soft ductile sulfide affecting deformation in the secondary shear zone. Type 416 containing relatively high manganese for improved machinability shows good general properties. The effects of increasing manganese content on mechanical properties, cold formability, and corrosion resistance are described. THE addition of sulfur is commonly used to improve the machinability of stainless steels. However, little attention has been paid in the past to the composition and characteristics of the sulfur-containing phase or phases present in these resulfurized steels. Recent information on the properties of sulfide phases, and their role in metal cutting, suggests that variations in these phases could have critical effects on machin-ability, as well as important effects on formability and other properties such as corrosion resistance. Manganese, chromium, and iron are strong sulfide forming elements present in stainless steels! of these, manganese has the greatest sulfide forming tendency and iron the least.1"1 The manganese content of resul-furized 13 pct Cr steels, often about 0.5 pct, can be insufficient or only barely sufficient to combine with the sulfur that is present; thus, the precise level of manganese can strongly influence the nature of the sulfide phase. Sulfide phases which may be present in stainless steels have been reported to include CrS, a spinel-type sulfide, chromium-rich manganese sul-fide, and manganese Sulfide.5,6 Detailed phase relationships for the Fel3Cr-Mn-S system have been reported by the present investigators,7 and a portion of this work will be referred to subsequently in this paper. Recent work by Kiessling6 and Chao et a1.8 has shown that sulfide phases can display wide variations in hardness, and may undergo considerable plastic deformation under isostatic loading.9-12 Early theories of metal cutting attributed the influence of sulfur to a lubricating effect. It is now apparent that the influence of the nonmetallic inclusions and their properties on crack initiation, deformation in the shear zones, and boundary films must also be considered in relation to the machining process. This paper presents the results of studies conducted to relate machinability to the various sulfide phases which occur in stainless steels. This work has led to the development of alloys with improved machinability, and has generated information on the effects of inclusions on metal cutting processes. Effects of sulfide inclusions and steel composition on other important metallurgical properties are also discussed. MATERIALS For drill machinability and inclusion studies, 10 lb laboratory heats were melted in an air induction furnace. These heats were made with sulfur contents be tween 0.10 and 0.50 pct and manganese contents be tween 0.05 and 3.0 pct. Residual elements were added to the heats in amounts typical for commercial steels. The typical compositional range covered by the heats is shown below: C Mn P S Si Ni Cr Mo Cu N 0.10 0.05 0.007 (M0 0.40 0.40 13.0 0.20 0.10 0.03 3.0 0750 The laboratory ingots were forged in the temperature range of 1800" to 2100°F to 3/4-in. sq bars, and all bars tempered to a hardness aim of 200 Bhn prior to testing. Because of differences in composition and tempering response, the tempered bars showed some variation in hardness (175 to 275 Bhn) as well as variations in delta ferrite content (0 to 50 pct). Composition, hardness, and delta ferrite content were considered in the analysis of the machinability data. Additional tests involving tool-life evaluation and determination of other properties were conducted on materials from commercially melted and processed 15-ton electric furnace heats. TESTS AND PROCEDURES Machinability of the laboratory heats was evaluated in a drill test. In this test, 1/4-in. diam holes, 0.4 in. deep, were drilled alternately in a test bar and in a standard bar for a total of four holes in each. This sequence was repeated three times using a freshly sharpened drill each time. The average time required to drill a hole in the test bar was compared to that for the standard bar. A drill machinability rating was assigned to the test bar relative to a rating of 100

Jan 1, 1970

By G. Donald Emigh

WESTERN phosphate resources which lie in Ida- ho, Montana, Utah, and Wyoming, have seen great expansion of activity in recent years. Growth has been two-pronged: expansion in fertilizer use, and since 1949, into the elemental phosphorous industry. Elemental phosphorous, produced in the electric furnace, goes largely into chemical making. Phosphate ore was first recognized in the West about 1889. Production started in 1906, and for many years consisted of underground operations by small companies operating sporadically. In 1920 Anaconda Copper Mining Co. opened the underground Conda mine near Soda Springs in southeastern Idaho, and has maintained and increased its operations since then. About 1930 Montana Phosphate Products Co. began underground mining in Montana and has remained a steady producer. In 1945 San Francisco Chemical Co., one of the oldest companies in the western field, initiated strip mining at the Waterloo mine near Montpelier, Idaho, and later at Leefe mine near Sage Junction, Wyo. In1946 J. R. Simplot Co. began open pit mining at Gay mine near Fort Hall, Idaho. In 1950 Victor Chemical Works began underground development work in the area of Maiden Rock, south of Butte, Mont.: and has since mined there. Monsanto Chemical Co. began open pit mining near Soda Springs, Idaho, in 1951.

Jan 11, 1954

By AIME AIME

THE list of deaths reported during the year 1904 comprises the following names (the figures in parentheses indicate the year in which the persons named were elected to membership). Honorary Members.-Sir Lowthian Bell, Dr. Thomas M. Drown. Members and Associates.-Jacob Neff Barr (1884), John Walter Best (1899), A. Poyntz Blandy (1903), A. Cass Canfield (1876), William E. Carroll (1901), William E. C. Coxe (1874), Russell W. Davenport (1877), Isidor Davidov (1893), Louis M. Davis (1884), Edward Doerr (1897), Edward M. Ferguson (1878), C. Le Neve Foster (1893), Geo. Clinton Gardner (1878), Wm. J. Harris (1871), Richard P. Heckscher (1893), H. D. Hoskold (1.894), Wm. S. Hungerford (1882), Edwd. K. Landis, (1882), August Lengemann (1902), Wm. M. Lippitt (1900), Henry McCalley (1888), Robert J. McCartney (1897), Arthur McClellan (1871), Arthur S. Mahony (1888), Philip W. Moen (1888), Henry G. Morse (1881), Charles Parkin (1875), Clarence V. Page (1900), Rubens P. Patterson (1886), Henry Paul (1889), W. H. Pettee (1871), James B. Randol (1879), Irving H. Sevier (1904), Win. J. Sims (1902), John H. Slavens (1901), Chas. B. Squier (1886), Chas. W. Stickney (1891), Homer H. Swaney (1903), Walter B. Wilson (1892), Whittaker Wright, The following paragraphs, constituting the concluding portion of the Annual Report of the Council for 1904, have been withheld from publication until now, in order to make them as accurate and complete as possible. Jacob Neff Barr, a mechanical engineer of note, died on May 5, 1904. Being especially interested in railroad work, he invented the Barr contracting-chill process of casting car-wheels,

Jul 1, 1905

By Henry M. Howe

In my original paper, Piping and Segregation in Steel Ingots, I pointed out1 among other things that, in view of the slighter stretching (virtual expansion) of the crust, and greater opportunity for sagging, there should be less piping in broad than in narrow ingots, and less in slowly-cooled ingots, e.g., those cast in pre-heated sand molds, than in those which cool quickly, e.g., those cast in iron molds. A. A. Stevenson said that neither of these predictions agreed with his own experience. In particular, in a picture which he showed of a wide and of a narrow ingot cast from the same ladleful of steel: the wide ingot had certainly piped much more deeply than the narrow one. At the time I did not see the explanation of these discrepancies, but further reflection makes it evident. One of the most important elements in determining the depth of the pipe is the degree of " top-lag," that is, the degree to which the solidification of the top of the ingot lags behind that of the bottom. Through this lagging the steel of the upper part of the ingot is able to run down and fill the pipe below as fast as it forms. To the importance of this lagging I called attention in my original paper.' Sand us. Iron Molds.—If we compare two like ingots, one cast in an iron and the other in a sand mold, we see that the top-lag is much greater in the former than in the latter, because in the former the lower part of the ingot is cooling off fast while the metal is running into the upper part. It is perhaps easier to look at this as a case of the solidification of the hot-

Jan 1, 1910

By H. I. NORTON, H. O. Hofman

ZINC smelters in the central western. States have established a very high standard of purity for blende-concentrates, viz., zinc 60, iron less than 3, and lead less than 1 per cent. The very low percentage of iron is made possible by the blende containing less than 0.5 percent of isomorphous iron sulphide and by the sparing occurrence of pyritic material in the large blende-deposits of southwestern Missouri and southeastern Kansas. The blende in these districts occurs in sub-Carboniferous limestone, and is associated with chert, residual clay, calcite, pyrite or rnarcasite and bitumen. The different minerals are coarse and therefore readily separated by mechanical washing from the blende, with the exception of pyrite and marcasite, as blende has a specific gravity of from 3.9 to 4.1, marcasite, from 4.85 to 4.90, and pyrite, from 4.95 to 5.10. The common procedure of dressing the ores is to crush in a breaker, size in a trommel with 0.5-in. holes, pass the over-size through roughing-rolls and then jig the ore, now reduced to 0.5 in. maximum size, in roughing multiple-sieve jigs. The products of these are waste-tailings, sine-discharge coarse concentrates, side-discharge coarse middlings and bottom-discharge fine middlings. The coarse concentrates are sent to the market. The coarse middlings are crushed in middlings-rolls and brought back into the system by feeding into the main trommel. The fine middlings are cleaned upon finishing-jigs. Any pyrite or marcasite present follows the blende and increases the percent-

Mar 1, 1905

R. F. WOOD,* Sandusky, Ohio.-I made a few tests of gun-metal specimens, after I noticed the results on quenching -reported by the Bureau of Standards. The data of one such test are given herewith. The bars were heat treated and quenched before they were machined, and in all cases they were brought up to 700° or 800°. They became extremely brittle,, showed almost no elongation, except such as was caused by the failure of the pieces to fit together after they were pulled, and the tensile stength was reduced from around 35,000 to about 13,000 lb. per sq. in. In addition, the weakening effect of the quenching seemed to be almost as marked when the bar was allowed to slowly air-cool from red to black, and then quenched, as it was by quenching directly from the red heat. Test Bars.-Rough size, 9/16 in. diam. over test section, grips 13/16 in. diam. Cast two in a flask, one on each side of a block 8 by 4 by 1 in. and fin-gated thereto from the grips but not from the test section. Poured with flask in inclined position, with gate to lower end of block and riser from upper end of each test bar. Bars were machined to ½ in. over the test section, after heat treatment. Casting the Bars.-Charge of 1500 lb. consisting of 400 lb. of new metals and 1100 lb. of G turnings and scrap was melted in open-flame oil furnaces and then poured into a 1-ton ladle. From the ladle 150 lb. was poured into a preheated No. 50 crucible, land from this the flasks of test bars were poured. The six flasks are indicated below by the numbers 1 to 6 and the bars in each flask by the letters a and b, thus 4a and 4h, for instance, were the two bars in flask No. 4.

Jan 12, 1919

By J. C. Bradley

The relation of annealing temperature to conductivity of copper wire has been determined. Conductivity hard was 98.26 per cent. After a 10-min. heat,ing at 200" C. it was 98.69. By annealing 10 min. at 300" C. a large increase, to 100.93, occurred. Maximum conductivity, 101.15, was attained after a 500" C. anneal; thereafter it decreased to 100.53 after a 950" C. anneal. If copper is gassed the decrease is much more than this. Material and Method The work was done on high grade electrolytic copper, 99.942 per cent, copper plus silver, silver 0.0008 per cent. It was hot-rolled to 1/4 in., then cold drawn to 0.080 in. The wire was cut into 25 5-ft. lengths and numbered 1 to 25 as cut. Four samples were tested hard. The others were wound into 5-in. diameter coils. For the 100" C. heating a coil was put into water, the water brought to . boiling, and the wire kept at this temperature for 10 min. For the higher temperatures the coils were placed in envelopes of sheet copper, a little water added, and the envelopes sealed by folding over the edges twice, and hammering them together. This kept the air out very well. The envelope and wire were brought to the desired temperature; this was maintained for 10 min., then the whole was water-quenched. Results Data from the tests are shown in the table and plot (see Fig. 1); conductivity is referred to the International Annealed Copper Standard at 20" C. Conductivity hard is considerably less than conductivity soft.1 The increase is sharp when the wire anneals. The maximum, 101.15 per cent, in the particular material used, comes at 500º C.; thereafter the conductivity falls to 100.53 per cent. after 950" C. annealing, a drop of 0.62 per cent.

Jan 1, 1927

By B. A. Stainton, John D. Gill

OUR combined economic activities have as their goal the maximum of individual well-being and national security. In this age of intense international competition the two objectives are closely related. For many decades, the maximum of well-being and ability to maintain national security have moved generally upward. The best single measure-perhaps the only adequate measure -of the level of the rising goal is the per capita real national income (national income corrected for price changes). For centuries before the industrial revolution the income of the world's population changed little from generation to generation. In our country prior to 1800 the growth of national income was hardly measurable from decade to decade. Since 1850, perhaps since the "industrial revolution," the growth of per capita real income has been increasing geometrically. Of major importance is the accelerative growth of the productive ability of our economy. Inadequate consideration of its implications is partly responsible for periodic delays in solving our princi-

Jan 1, 1946

By A. E. Nehrenberg

THE mechanism by which austenite forms in steels has received a great deal of attention in the literature in past years.'-'* Our present knowledge concerning this mechanism has been recently summarized quite concisely by Bain and Vilella,1 while a few years ago the literature was carefully reviewed by Roberts and Mehl.² The consensus is that any ferrite-carbide interface is a potential site for the nucleation of austenite during heating above the Acl temperature, and that the new austenite generally grows freely to produce approximately equiaxed grains, whether the carbides are initially present in the lamellar or the spheroidal form. In the case of eutectoid steels, growth of the new grains of austenite continues until contact is established with other grains. Then growth stops and an initial austenite grain size is established which does not change until the heating is continued to some high temperature at which grain coarsening begins. In the case of pearlitic steels which are not of eutectoid composition, the proeutectoid ferrite or carbide may interfere with the growth of the austenite if the temperature is not above that designated the A63 or the Acm, respectively. Although a large amount of work has been done to establish the mechanism of austenite formation in steels, it became clear to the present author while he was studying the transformation characteristics of a new 0.25 C Mn-Si-Ni-Mo hypoeutectoid steel" that the manner in which austenite grows in steels depends upon some factor, or factors, not previously considered. This was indicated by the fact that when this steel in the spheroidized condition was heated above the Ae1 temperature the new austenite which was formed did not envelop the carbides and grow in an equiaxed manner as described by Bain³ or spheroidized steels. Instead, in this steel, the austenite was observed to grow much more readily in certain directions than in others with the result that at temperatures within the Ac1-Ac³ ransformation range the austenite grains were acicular in shape. The excess ferrite was also found to be acicular with the distribution of these phases being such that a lamellar pattern was developed. This unusual directional growth of austenite in this new steel initially in the spheroidized condition is illustrated by fig. 1. A search of the literature revealed that this type of growth was not necessarily peculiar to this steel for similar microstructures had been observed by other investigators.4-8 However, the full significance of these microstructures does not appear to have been appreciated, and no work has been done to determine the conditions responsible for this directional growth of austenite or to arrive at an understanding of it. It was for this purpose that the work described in the present paper was carried out. Material: During the course of this investigation a total of 15 steels was studied. They consisted of hypoeutectoid, eutectoid and hypereutectoid carbon steels, and hypoeutectoid and hypereutectoid alloy steels, all of which were obtained in the annealed condition from commercial warehouse stock. As received, the carbon and alloy hypereutectoid steels had microstructures which consisted of spheroidal carbides in ferrite, whereas the eutectoid steel and the hypoeutectoid steels were pearlitic. The grades of steel represented were 1050, 1080, 10110, 3310, 4140, 4340, 4615, 6145, 8620, 9260, 9442,

Jan 1, 1951

By Strathmore R. B. Cooke

On the basis of experiments con- ducted on quartz using a bubble pick-up method, it was shown in an earlier paper1 that this mineral will preferentially adsorb hydrogen, calcium, or sodium ions, depending on the relative concentrations of those ions in the solution in which the quartz is immersed. For quartz particles ranging in size from 0.2 to 1 mm, it was demonstrated that the concentration of calcium in solution (assumed present as ions) necessary to completely activate quartz for flotation is given by the expression: In this expression, ionic concentrations are in mols per liter. It was further shown that the pick-up method is apparently more sensitive to changes in reagent concentration than the standard captive-bubble method, and that induction times are apparently much reduced. Since completing these earlier tests, a new type of cell has been constructed; this is shown in Fig 1 and 2. In Fig 1, A is a ground joint, B is a ceutral tube reaching to within a few millimeters of the bottom of the cell, and C is a stopper which may be removed for re- agent addition, and serves the further purpose of excluding carbon dioxide from the air during the test. The entire cell is constructed of Pyrex glass, and does not give the trouble experienced with the earlier cell, in which activating ions were released from the glass at high pH values. The only critical factor in the construction of the cell is the clearance between the central tube and

Jan 1, 1949

By F. H. Vitovec, D. W. Hoeppner

Pusk-pull fatigue tests were conducted on copper tricrystals of 99.988 pct purity to ascertain the role of grain boundaries in the initiation and propagation of fatigue cracks. Significant differences in behavior were found for specimens which possessed different transverse-boundary misorientation. In speciwens with low boundary angles cracks initiated within the transverse boundary, while higher angles led to transcrystalline fatigue failure. It is suggested that at low angular misorientation moving dislocations may interact with dislocations of the boundary or dislocations present in adjacent pains on favorably oriented glide planes, thus initiating a fatigue crack. MANY fatigue studies have been concerned with fatigue-crack initiation within grains and the mechanism causing initiation and propagation1-3 Although the initiation of fatigue cracks in or near grain boundaries of pure metals has been observed and reported in the literature, the mechanism of this phenomenon has received little attention.4"11 EXPERIMENTAL PROGRAM Testing Procedure. To investigate the role of grain boundaries regarding initiation and propagation of fatigue cracks, copper tricrystals were tested in push-pull. Axial-stress tests were used to avoid the stress gradients introduced by stressing of some other nature. Copper was selected as the most suitable test material since extensive work has been done on the formation of fatigue-induced slip in copper. Tricrystal specimens were used to provide a grain boundary geometry with one boundary transverse to the principal stress axis and one or more boundaries nearly coincident with the direction of maximum resolved shear stress. The boundary energy and the slip characteristics in the vicinity of the transverse boundary depend on the relative orientations of grains across the boundary. Testing was done at room temperature, at a frequency of 700 cpm, in an atmosphere of either air or argon. It is known that the incidence of grain boundary cracking increases with increasing temperature and decreasing frequency.4 The fatigue machine applied a uniaxial tension-compression load to the specimen by a flat spring which was actuated by an adjustable eccentric. Use was made of an adjustable head and a load cell which had strain gages mounted at 120-deg intervals around its periphery, thus providing a means for eliminating any detectable superimposed bending moment. A clip gage was mounted between the gripping heads to record the cyclic strain amplitude applied to the specimen. Each specimen's hysteresis characteristics were recorded by supplying the load and strain signals to an oscilloscope. Microstructural changes were observed and recorded with an optical microscope which was mounted on the fatigue machine. Immediately prior to insertion in the machine, each specimen was chemically polished. Extreme care was exercised while inserting the specimen in the test machine to avoid either bending the specimen or introducing a mean load. Each specimen was stressed in the tensile direction first and subsequently the load was reversed. Specimen Preparation. Tricrystal fatigue specimens of 99.988 pct Cu were grown from the melt using a modified Bridgman technique. Ingots about 1 in. high were grown to the configuration shown in Fig. 1. Upon sectioning the resultant ingot, several specimens were provided with an identical shape and grain boundary orientation. Except for plane sectioning and final polishing, this method eliminated machining the specimens. The apparatus used for growing the tricrystals is shown in Fig. 2. A spectrographically pure graphite mold, Fig. 3, was inserted in a vycor tube which was mounted on a vertical zone-refining table. Prior to insertion in the tube the mold was assembled as follows. The insert and graphite rods were fixed in position in the mold. The copper was then placed in the mold and the entire mold assembly was positioned in the vycor tube, Fig. 2. At this point the tube was sealed, evacuated, purged with helium gas, and finally placed under a slightly positive helium pressure. The heating coil was then adjusted to melt the copper charge, after which it was raised at a speed of 4 in. per hr. It is also possible to use

Jan 1, 1964

By A. C. Fieldner

COKE and by-products have prime importance in the war program. The past year was marked by the construction of new and the rehabilitation of old by-product and beehive ovens and by the increase of production from existing plants to practically 100 per cent capacity. W. T. Brown's paper, "Plan to Improve Blast-Furnace Coke," presented at the Fuels Conference in St. Louis, Sept. 30, showed how the blending of low- and high-volatile coal improved the physical properties of coke and that improvement of the quality and uniformity of coke favored an increase of blast-furnace capacity- a vital need in the war program. Others in the industry have likewise increased production of coke or recovery of by- products by various innovations or changes in operation. Recognition of the value of pooling these developments for the benefit of the entire industry led to organization of a survey of coke- oven plants and blast furnaces by the Bureau of Mines in co-operation with the Solid Fuels Co-ordinator with a view to improving metallurgical coke production and recovery of by-products. This survey is being conducted with the help of an advisory committee consisting of representatives of the Bureau of Mines, the Solid Fuels Co-ordinator, the War Production Board, and the blast-furnace, coke-oven, and coal-mining industries.

Jan 1, 1943

By Norman Weiss, H. W. Kaanta

CUSTOM ores reach across the New Mexican mesa to American Smelting & Refining Co.'s new lead-zinc mill at Deming. The influx of ores justified increasing mill capacity from 12,000 tons per month to 20,000 tons per month with the installation of a second milling section. Deming mill has met a complex material handling problem with the successful instrumentation of modern machinery and knowledge. A tight, compact plant does a big job with the aid of the latest ore moving equipment. Location and Layout The mill is located three miles northwest of Deming in the tumbleweed covered valley of the Mimbres River, 30 miles north of the Mexican border. Deming has a population of 4000 and is about halfway between Lordsburg and Las Cruces and 54 miles southeast of Silver City. The AT&SF and the SP railroads and U.S. Highways 70, 80, and 260, cut across the mesa to the town. Asarco mill station is east of the AT&SF single track, and north of Deming. The nearly level terrain is covered with fine sand supporting only yucca and tumbleweed. Compacted gravel at depth affords excellent foundation bearing. The climate is semi-arid, but the district is underlain by water-bearing strata. Tailing disposal space is plentiful. The Deming site appeared favorable because of easy rail and highway access, central location in a mining district, excellent climate, plentiful water supply, space for all present and future requirements, and proximity to a town. The milling plant is a 250-ft square. The rail spur forms the west side; sampling plant, fine-ore conveyor and bins are on the east; track hopper, primary conveyor, and crushing plant lie on the south; and the mill building completes the north side of the square. Construction The mill site was chosen and the land purchased in 1,946 and 1947. Design began in 1948, and Stearns-Roger Mfg. Co. of Denver started construction in June 1949 completing work in April 1950. Construction is steel and concrete throughout, with main concrete floors supported on cellular steel beams. The building is covered by galvanized corrugated iron, attached to the frame by welded Nelson studs, and made dust tight at the joints with roofing paper and asphalt sealing compound. Crushing and Sampling Custom ores, delivered to the mill by railroad cars or trucks, are weighed on arrival. A Robbins car shaker dumps the ore into a 100-ton capacity steel hopper. Adjacent is a 40-ton truck hopper. Three 36-in. Pioneer apron feeders supply ore from the receiving hoppers to a 36-in. conveyor which runs to the crushing plant. A tramp-iron detector protects the primary crusher except when handling magnetite containing ores. A 2 ½ -in. spaced grizzly precedes the primary Traylor 24x36 in. jaw crusher set at 4 in. A Symons 4-ft cone crusher in closed circuit with 48x78 in. Robbins Gyrex screen completes crushing to 5/8 in. The discharges of both crushers drop upon a common conveyor, which, after gaining sufficient elevation, transfers ore to a return conveyor. This return conveyor passes under a suspended magnet and over a magnetic head pulley to the Gyrex screen. Screen undersize is conveyed by a 20-in. belt to the sampling plant. Crushing rate varies from 60 to 90 tons per hour. Ores containing magnetite and pyrrhotite nullify the magnetic detector and overload the magnets

Jan 1, 1952

By T. A. Rickard

An educated man is distinguished neither by his clothes nor by his knowledge; he is replarkable not for the things he says, but for the way he says them. You cannot even stand with him under an archway in the rain without finding him out. He may talk only of the weather. His words and his phrases alike may be simple. -at distinguishes him is the arrange- ment of his words; however desultory his talk, it will be method- ical; he has habituated himself to foreseeing the part to be played by each word he uses and the place to be taken by each sentence he utters. On the other hand, the uneducated man, though shrewd and well-informed, will relate facts and events as they recur to him, generally in disorder; in his effort to recollect and in his attempt to rectify forgetfulness he will pause irregularly, filling the intervals with meaningless phrases, such as "and then ", "and: so ", or 'said he to me", "said I to him"; and even the contipuous parts of his story will be told confusedly-because he has not learned the proper use of words.* My own experience as an editor of technical manuscripts has taught me that the misuse of 'that' and 'which' is a fruitful cause of obscurity and confusion. The relative pronouns have distinct functions, and no writer can express himself clearly until he has learned to discriminate between these I functions. For example:

Jan 1, 1931

By F. H. Bunge, W. H. Jr. Dailey

This paper covers an investigation of the magnetic roasting characteristics of several iron ores when treated in the form of small pebbles (1/8" to 1/2" in size), and in the form of balled fines. The roasting treatment was carried out with apparatus capable of very close control of time, temperature, face velocity, and per cent combustible in the reaction gas. The effect of rapid initial heating was not studied although it is believed that this has a major effect on the results when processing solid pebbles. The test equipment is a fixed bed type, with such a wide range of gas velocities, temperature, combustible content and etc., that the results obtained can be made to approximate those from various commercial roasting processes. The data presented in this report covers reaction rates, effect of processing variables on silica in the concentrate, flow resistance of beds, and to a limited extent, the effect of particle size. The work is far from complete and raises many more problems than it gives answers for. We believe, however, that much of the information will be useful to those engaged in investigation of magnetic roasting processes. We measured the time required for various degrees of completion of the reaction of hematite to magnetite, for finely pound material in balled form and for carefully sized crushed ore. Measurements were made for a variety of Minnesota and Labrador ores. This report covers an ore requiring fine ginding (-325 M) for liberation (Lower Kevin) and an ore requiring coarser grinding (-100 M) for liberation (Upper Olson). These ores represent approximately the range of characteristics for a group in the west end of the Mesabi Range. Our data shows that the reaction rate is very fast for the finely ground material and that tests are readily reproducible. The reaction rate of the larger size material, in the range of 1/8" to 1/2", is much slower and the results more erratic. We found that for the ores tested, the percentage of silica in the Davis tube magnetic concentrate was a function of iron recovery. Normally the concentrate had a low and relatively uniform percentage of silica up to a critical value of recovery. Above this critical recovery value the percentage of silica increased very rapidly. For example, for one particular ore roasted in the form of 3/8" diameter balls made from -28 mesh fines, the silica remained at about 7% to 8% until the recovery exceeded about 93%. Increasing the recovery beyond 93% resulted in over 25% silica with the additional recovery. The degree of conversion of hematite to magnetite (% completion of roast) required to obtain 93% recovery for balled material, varied inversely with the gas flow rate. Percentage silica in the concentrate resulting from roasting 3/16" and 1/2" solid material was relatively erratic. However, for varying degrees of iron recovery the lowest silica percentages corresponded to those obtainable when roasting fines. It is thought the probable reason for the erratic values was the variation in shattering or cracking of the pebbles during initial heating and roasting. There is some indication that very fast initial heating will greatly increase the permeability of the individual particles of ore to gas flow so that the reaction rate for coarse sizes will approach that obtainable with balled fine material.

Jan 1, 1961

By W. E. D. Stokes

The faster that aircraft fly the sooner some new and stronger material must be found to take the place of the present aluminum alloy used in all-metal planes. Experts of the National Advisory Committee for Aeronautics. in studying hi-speed aircraft, are convinced that the present all-metal plane, of semi-monocoque, aluminum alloy construction, is not the ultimate in aircraft design. Magnesium alloys and steel are under consideration.

Jan 1, 1942

By C. A. Wert, K. C. Hsieh

Measurement has been made of the organic sulfur concentration in coal macerals using microanalytical techniques in the transmission electron microscope. This technique utilizes measurements of x-rays emitted by the sulfur atoms embedded in the hydrocarbon constituents and the bremsstrahlung x-rays generated in the matrix. It is a simple technique for thin specimens and yields reliable results. Although it can be used to measure the average organic sulfur content of coal, it is most useful in determining organic sulfur in extremely small volumes of material. Variations in organic sulfur content can be measured at a scale unimagined earlier. This TEM technique also has application for determination of organic chlorine, phosphorous, potassium and other elements often found distributed through the hydrocarbon constituent of fuels.

Jan 1, 1985

By A. F. Crawley

THIS communication reports measurements of the densities of dilute liquid alloys of 0.1 and 0.5 pct Ag in Sn over temperature ranges of 170" and 210°C, respectively, above the melting point of pure tin (232°C). The work was earried out to provide accurate density data for some liquid diffusion studies performed by Davis.1 Densities were measured using a pycnometric technique established in this laboratory. Earlier papers2, 4 attest to the accuracy of ±0.05 pct and the reliability of the method. Tin, 99.999 pct pure, and silver 99.99 pct pure, were melted in a graphite crucible in a vacuum furnace and held at temperature for 10 hr to ensure homogenization. Ingots suitable for machining

Jan 1, 1970