Search Documents

By E. M. Norris

In the summer of 1917 it was decided to fireproof the main tramway hoisting shaft of the Anaconda Copper Mining Co. at Butte, Mont. The shaft has three hoisting compartments and one pump compartment; it is timbered with 12 by 12-in. (30.5 by 30.5-cm.) fir timber, and is 2475 ft. (754 m.) deep. Subsidence and displacement of the surrounding country rock had produced exceedingly heavy ground, and had carried the shaft out of line, in several places, by as much as 2 ft. (0.6 m.) displacement. Constant repairing and realigning of the timbers had been necessary in order to maintain clearance for the cages. The most feasible method of fireproofing, therefore, seemed to be to cover the timbers with a coat of concrete applied with the cement gun. The cement gun, which is operated by compressed air at ordinary mine pressures, feeds a mixture of sand and cement through a hose to a nozzle having a water connection. The mortar in fluid form is thus sprayed upon the prepared surface in thin layers, which can be built up to any desired thickness. The cement gun can be set up at any convenient point; satisfactory results have been obtained with the nozzle a distance of 500 ft. (152 m.) from the gun. The shaft was thoroughly overhauled and the timbers put in the best possible state of repair. Between the 1000 and the 1400 levels, much loose ground lay against the shaft timbers on the north side; this was breast-boarded back and a 30-in. (76-cm.) reinforced-concrete retaining wall was erected, leaving a space of 12 in. (30.5 cm.) outside the shaft timbers to allow for future movements of the ground. For convenience in handling men and materials; it was arranged to concrete the auxiliary hoisting-cage compartment and the pump compartment first, using the cages of the main hoist to serve the cementing crews. The auxiliary cage was then available while the remainder of the shaft was being concreted.

Jan 3, 1918

By G. C. McLachlan

Two papers dealing with Noranda's milling operations have already been presented. The first1 of these covered the initial metallurgical problems connected with the treatment of the ore, while the second2 described the development of the mill from a 500-ton unit in 1928 to one with a daily capacity of 3000 tons less than six years later. At the time the second paper was written the equipment whirh had been installed to bring the mill capacity up to 3000 tons was being tuned into production and for this reason, though each step had previously been tested by a large-scale pilot operation, it was thought advisable to withhold metallurgical data until any starting-up difficulties had been overcome and anticipated requirements fulfilled. These requirements called for an improvement in gold recovery without any lowering of the previous ratio of concentration, and the pages that follow deal with the methods by which this result was obtained. An idea of the character of Noranda concentrating ore will be gained from an inspection of the following mineralogical analysis of the ore treated by the mill during 1933: MineRal Content Mineral ConteNt Chalcopyrite, per cent..... 6.8 Silica and silicates, per cent............ 18.3 Pyrite, per cent........... 22.1 Gold, native and as telluride, oz. per ton 0.15 Pyrrhotite, per cent....... 51.5 Silver, probably as argentite, oz. per tou 0.35 Magnetite, per cent....... 0.5 Thesr figures, which are typical, show that over 73 per cent of the ore treated consists of pyrite and pyrrhotite. Determirnation of the proportion of unrecovered gold associated with each of these minerals was therefore of primary importance in developing a suitable method for improving gold recovery. As pyrrhotite is magnetic, this information was obtained by making magnetic sorting tests on samples of the mill tailing and screening the material thus segregated. This showed that the magnebtic material finer

Jan 1, 1935

By Arthur Notman

TO present some idea of the magnitude of the gold-mining industry of Canada and the world, the records of 106 gold-mining companies currently paying dividends have been studied. Forty of these are in Canada, and 37 on the Rand in South Africa, these being all the straight gold-mining companies that paid dividends in the two areas in 1938. None of the base-metal companies that produce gold as a by- product, or even as a major fraction of the value of their total product, have beezl included. In addition, a group of 29 similar companies from Southern Rhodesia and the Gold Coast in Africa, India, Australia, Manchuria, Philippine Islands, the

Jan 1, 1939

By A. T. Churchman

The deformation modes of rhenium have been identified as those typical of the hexagonal metals, titanium, zirconium, and beryllium whose c/a ratios, in common with rhenium, are less than ideal for close packing. Slip is observed on (1010), (1011), and (0001) planes and twinning on (1121), (1122), and (1012) planes. The very high rate of work hardening is believed to be associated with intersecting partial dislocations on two (1010) systems which can combine to form sessile barriers. If the stacking fault energy is low, as postulated by Seeger, these barriers should be strong and not easily bypassed by cross slipping. Such an explanation could also account for the very small temperature dependence of the yield stress which was observed. RHENIUM is interesting scientifically as a member of the group of high melting point hexagonal metals: titanium, beryllium, and zirconium with a c/a ratio less than that for ideal close packing. Unlike them, however, it work hardens at a very high rate. This rate is greater and continues to a much higher degree of deformation than for nickel, normally considered to have a high rate of work hardening. This paper presents experimental observations on the modes of deformation of rhenium and, by comparison with other hexagonal metals, some speculation on the cause of the high work hardening. MATERIALS Johnson, Matthey rhenium powder of both 99.9 pct and 99.5 pct purity, see Table I, was compacted at 10 tons per sq in., part sintered at 1350°C in vacuo, and finally arc melted in a "gettered" argon atmosphere arc furnace to produce small buttons. Little difference was observed in the as-cast hardness or working down behavior of the two purities suggesting that either silicon and potassium do not have a significant effect on the working properties of rhenium or they were lost during arc melting. SPECIMEN PREPARATION The cast structure was broken up by cold-rolling with inter-stage annealing at 1600o or 1800°C in a vacuum high-frequency furnace using a tungsten susceptor. Strip for tensile testing was taken from two thicknesses of material 0.011 and 0.064 in. The former with intermediate anneals at 1800°C had a grain size of 900 grains per sq mm, while the latter with inter-stage annealing at 1600°C had a grain size of 3600 grains per sq mm. A coarse grain size was obtained by secondary recrystallization in a half button cold-worked by 30 pct reduction. Annealing times of from half an hour to several hours at 2200° to 2600°C in a "gettered" argon atmosphere arc furnace1 resulted in grains of up to 2 mm diam.

Jan 1, 1961

By Samuel B. Christy

At the last meeting of the Institute, several contributions were made to the subject of miners' aid funds. Such matters will always form important factors in the administration of large industrial enterprises. From the frequently remote and isolated position of mining properties, it is a subject that often forces itself upon the attention of the mining engineer. Local conditions are usually so variable that no single method can be found equally well adapted to all localities. At the same time, a study of different types is often suggestive and valuable, and it is with this in view that these notes are presented. The Miners' Fund of New Almaden is a remarkably successful example of what may be done for miners by a wise and at the same time firm management, by simply directing their own efforts and without incurring any great expense to the stockholders,—a practical consideration not without importance in most cases. The quicksilver mines of New Almaden are situated at a distance

Jan 1, 1885

By Carle R. Hayward

(Wilkes-Barre Meeting, June, 1911.) THE growing importance of metallography has caused a corresponding interest in the improvement of apparatus for preparing specimens of metals and alloys for microscopic examination. The purpose of this paper is to describe an electric heating-furnace, a grinding-and-polishing machine, and a device for mounting specimens, which are used in the metallographical work at the Massachusetts Institute of Technology. These three pieces of apparatus were designed and made in the laboratory of the Institute, and. each possesses some original features which may be of interest. ELECTRIC HEATING-FURNACE., The accurate control of heat necessary for metallographic work is best obtained by the electric-resistance furnace. Unfortunately, however, even the platinum-wound furnaces deteriorate with use and ultimately burn out, while the cheaper resistance-materials are often short-lived. Since the resistance-coil must be replaced from time to time, it is of advantage to be able to make this change with as little trouble as possible, and this is an important feature in the furnace shown in Fig. 1. A is a cylindrical galvanized-iron can, with two handles, B. A porcelain tube, C, passes through the central hole in the cover of the can and rests upon the asbestos disk, D; the bottom of the tube is held in place by the asbestos ring, E. The space, F, around the tube is filled with powdered magnesia. G is an ordinary assay-crucible, with the cover inverted so as to present a smooth top for supporting a second porcelain tube, H. The latter is wound with ?Excello " resistance-tape, 0.014

Dec 1, 1911

By B. T., Colley

AS always when metallurgical operations are conducted within or close to agricultural and stock-raising regions, the question of damage due to fume and smoke presented itself when the Cerro de Pasco Copper Corporation's new smelter commenced to operate in La Oroya in 1922, For more than twenty years the Corporation had operated its old plant close to Cerro de Pasco without encountering difficulties from smoke claims, owing to the fact that it was in an open plain where more or less constant air currents carried and dissipated the smoke over large areas, affording ample dilution. But Oroya is in a deep canyon formed by four contributing valleys up and down which the smoke travels for long distances in a more or less concentrated form. Though the altitude of Oroya is more than 12,000 ft., and the surrounding country rises to much greater elevations, nevertheless there exists there a large and important stock-raising industry and also a considerable development in agriculture, consisting of the cultivation of potatoes, barley, etc.

Jan 1, 1945

By H. I. Althulee

The mines operated by the Compañía de Real del Monte y Pachuca, Pachuca, Mexico, are in two districts, the Pachuca, and Real del Monte. The principal area of mineralization is within a rectangle roughly 10 miles from east to west and 6 miles from north to south. It contains a number of veins from 2 to 20 ft. wide, which are exploited by this mining company. The scattered position of the producing mines led to the construction of two mills between 1906 and 1908; the Loreto mill, in Pachuca, averaged 2600 tons daily, and the Guerrero mill, in Real del Monte, milled 1270 tons daily. On Feb. 1, 1929, the management decided to enlarge the Loreto mill to take the combined tonnage of both mills at that time. This economic measure required the centralization of ore delivery, which would also afford a material saving in the cost of ore transport. The centralization would give the company the following advantages over the former system of operation: 1. Beneficiation at a single mill, closer to source of materials and supplies than the abandoned Guerrero mill. The refinery is also in the Loreto patio. 2. Ore delivery to surface at one point (San Juan Pachuca shaft) instead of at four. 3. Elimination of aerial tramways. To show what would be required to effect this centralization, it is necessary to describe the means by which the ore was delivered to the two mills, prior to centralization. The heart of the Real del Monte district is roughly four miles from that of the Pachuca section. The producing mines in these two districts were: Pachuca district: Real del Monte district: Santa Ana mine La Rica group Camelia group Purisima group Santa Margarita mine

Jan 1, 1934

By H. Ries

In the marketing of mineral products, it is always highly desirable for both the producer and the consumer to be able to discuss things in a common language, and this can only be done if there are standard methods for expressing the properties of the raw materials. Having developed such a form of expression, the next step would be the making of specifications, which may serve as a basis for selecting raw materials. Considering the large number of non-metallic minerals that are used, there are not a few for which there are no standard laboratory tests to be used in determining their properties, or even standard specifications on which grades or market price may be based. Indeed in many cases the consumer simply requests the producer to submit samples, and rejects or accepts them without any explanation. Could the producer know in advance just what the consumer needed, time and money might often be saved. It appears to the writer that it is of the highest importance to devise standard laboratory tests wherever possible, as this enables the consumer to state definitely what he needs, and is of great assistance to the producer. It should also work to reduce misunderstandings and disputes. In the case of sands, we find that they show a wide variation in their character, ranging from those that are so coarse as to be of gravelly nature to those that are so fine that they might be classed as silt; and from very clayey ones to those that are practically free from clay. For this wide range of sands, we have a corresponding variety of uses, which are based mainly on the physical properties of the sand, although these are not always very definitely stated. The chemical composition need rarely be considered, if the sand is of siliceous nature. To determine and express these properties there should be standard tests, which are to be followed in all cases where the material is tested in the laboratory. The use of sands for foundry work (making molds or cores) is old, and it has been recognized for some time that the important properties to be

Jan 1, 1926

By D. R. Parrish, V. J. Berry

Reverse combustion is one thermal method of recovering hydrocarbons from porous undergrortnd formations containing oil or tar. In applying this method, air is introduced via an injection well and the mixture of air and hydrocarbons is ignited in the production well. A combustion zone then recedes toward the injection well, counter-current to the air flow. If the combustion-zorie temperature is sufficiently high, the oil or tar irz place is distilled arid cracked. The hydrocnrhon flows as a vapor to the production well and subsequently is condensed at the surface. Maximum temperature and velocity of morcment arc the two dependent variubles defining the progress of the combustion zone. A theoretical analysis has been made of heat flow in the reverse-comhustion process as.srtrning linear flow in a homogeneous system. The differentirll equatious, which include the oxygen-hydrocar-hon rctrction rate, have been solved numerically. Rescllts indicate that the maximum temperature reached and he cornbustion-zone relocity both increase with an incrense in air-injection rote. Heat loss to surroundings has little effect on the maximum comhustion-zone ten?perature achieved, but it is reflected in a reduced com-bustion-zorzc, velocity. It is also predicted that an increase in the oxygen-hydrocarbon reaction rate results in a reduction in the maximum temperature reached. The calculated results are in agreement with results from reverse-combustion experinments using samples of a tar sand. INTRODUCTION Reverse combustion is one thermal method of recovering hydrocarbons from porous underground forma-tions containing oil or tar.' In applying this method, air is introduced into the underground formation via an in-jection well. In one or more adjacent production wells, the mixture of air and hydrocarbons is ignited at the sand face. The combustion zone thus formed recedes toward the injection well, counter-current to the air flow (Fig. 1). Under certain conditions, the rate of recession of the combustion zone is sufficiently rapid that only a small fraction of the hydrocarbon at any point in the formation is consumed by combustion. If the combustion-zone temperature is sufficiently high, the uncon-sumed oil or tar in place may be partially distilled or cracked. This material then can flow as a vapor with the gaseous combustion products to the production well and subsequently be condensed at the surface. Under other conditions, the combustion-zone temperature may be so low that little, if any, of the hydrocarbon is vaporized. Nevertheless, the viscosity of the hydrocarbon may be reduced enough so that other recovery methods subsequently can be applied to produce oil at attractive rates. The maximum temperature achieved in the combustion zone and the velocity of movement are the two dependent variables defining the progress of the combustion zone. Presumably. knowledge of these factors will permit estimates to be made of oil recovery efficiency, oil and gas producticn rates and average amount of injection air required per barrel of oil recovered. The maximum temperature and combustion-zone vclocity are, in turn, expected to be dependent upon air flow rate, heat losses to surrounding formations, physical properties of the rock and the hydrocarbon. the extent to which the porous formation is saturated with the hydrocarbon, the rate of oxidation of the hydrocarbon and the amount of heat released. It is desirable that the relative importance of each of these factors be understood so that the results of laboratory tests of oil recovery by reverse combustion can be properly interpreted in terms of expected field performance. It is particularly desirable to assess the importance of heat lcsses because these are difficult to control or eliminate

By Paul F. Sikora, John W. Weeton, Philip A. Clarkin

Effects of variations in carbon content and micro-structure on the stress-rupture properties of a liquid-phase-sirztered, Izeut-resistunt alloy were studied. Using the powder rnetallurgy technique, specimens could be produced having stress-rupture profierties equivalent to or better than those of the alloy in wrought form. In addition, sintered specimens were easily hot worked even when carbon contents were as high as I pct. Correlations between stress-rupture properties and micro structure were obtained in some cases. IT is well known that many alloys used in high-temperature service are quite complex both from the standpoint of chemical composition and microstruc-ture. During the development of these alloys their complexity has in some cases led to treatment schedules which, while practical, often do not fully utilize available alloying elements. For example, in some alloys, massive carbides that form during ingot practice may never be dissolved by reasonable solution treatments and therefore are unavailable for subsequent precipitation hardening, Ref. 1. This investigation was undertaken to determine whether the powder metallurgy method of consolidation might provide distinct advantages over the conventional melting method. First, segregation of alloying elements might be eliminated or reduced and thus a more efficient use of these elements obtained. Second, the structures produced in powder specimens might differ considerably from those normally seen in castings, which would perhaps result in better response to subsequent mechanical or thermal treatments. If these results could be achieved, it was felt that both forgeability and stress-rupture properties might be improved. The alloy used in this investigation was S-816 produced by powder metallurgy methods. The influence of carbon content over the range of 0.1 to 1.0 wt pct was studied for the alloy in the as-sintered condition and after three additional treatments involving heat treatment, hot swaging, and combinations thereof. EXPERIMENTAL Standard S-816 has the composition shown in Table I. It is a cobalt-base alloy having a nominal carbon content of 0.4 pct and is classified as a precipitation-hardening alloy. This alloy was chosen because it is representative of a class of heat-resistant alloys and because adequate information was available concerning its response to various treatments and its subsequent properties. For this study, -100 mesh alloy powder having essentially the same composition as shown in Table I but without the 0.4 pct C was used. Desired carbon variations, achieved by wet mixing the alloy powder with graphite, ranged from 0.1 to 1.0 wt pct. Specimens were hydrostatically pressed and then sintered in vacuum by slowly heating until incipient melting was observed. Sintering this way gave a liquid phase in the interstices of the powder particles and achieved reasonably high densities. The average density of as-sintered specimens was about 95 pct of wrought alloy density. In order to obtain various microstructures, some specimens were heat treated (solution treated for 24 hr at 2150°F, water quenched; aged 16 hr at 1400°F, air cooled); others were hot swaged at 2150 o F (50 pct reduction in area), while still others were hot swaged (50 pct reduction in area) and then given the above heat treatment. During hot swaging it was observed that forgeability was quite good even when specimens contained as much as 1.0 pct C. Specimens were evaluated by stress-rupture test-

Jan 1, 1962

By E. H. Griswold

The many complexities arising from our present oil pool proration systems emphasize the need for a suitable standard of property rights. Attempts at conservation and unitization agreements have frequently failed because of the lack of such a standard. The necessity of reducing production to consumption has caused umpires, committees, commissions and other governing bodies to allocate the production of flush fields among the respective owners. The methods of allocation vary widely and conservation of underground reserves is frequently neglected or misused. Critical economic conditions increase, rather than modify, competitive methods. In some fields we have irregular and uneconomically close well spacing. Many operators drill unreasonably large holes, take excessive sand penetrations or leave their wells untubed in order to secure higher potential open-flow tests than their offsets. All of these practices result in economic waste and frequently damage to the pool. Regardless of our agreement with the fundamental principles of proration or unitization, both are actual necessities in many of our present economic situations, and we are in urgent need of a suitable standard of rights to facilitate and simplify their operation. The problems pertinent to unit management are simple and of daily use in many partnership enterprises, but the problems of fair and proper division of production under either proration or unitization are, as yet, subject to controversy. The rights of respective owners must be ascertained and standardized before we can eliminate wasteful practices and still preserve constructive competition in our industry. Valuation of Tracts In a recent unitization conference it was found that each participant had a different basis for calculating the relative values of tracts. Some of these assumptions were as follows: 1. Unrestricted open-flow operation to abandonment. 2. Current proration system to abandonment.

Jan 1, 1933

By Clyde E. Williams

THROUGHOUT its history the American iron and steel industry has constantly striven to improve the quality and reduce the cost of its products. No one needs to be told how well it has succeeded. Its success in making steel products at such a low cost has been achieved mainly through large-scale production. While costs have gone down as the rate of production and the degree of mechanization increased, quality of product has been actually improved. Thus high-tonnage records are important only in the light of high quality of the steel. Quality is the watchword! Continual improvement in quality has come as a result of research, not only in the laboratory but in the large commercial units in the plant. In fact, so many operations of the industry are on such a huge scale that experimental work must be done under commercial operating conditions so every progressive steel plant is a research laboratory.

Jan 1, 1938

By John Johnston

ONLY two of the Institute's 26 Local Sections were unrepresented at the delegates' three sessions, held on Monday morning and afternoon and Thursday afternoon of the annual meeting. The Philadelphia and Wyoming Sections alone sent no delegates. In all, seven hours were spent most profitably in reviewing the work done by the Institute at headquarters and in the field, comparing ideas and practices in varied activities, and in establishing personal contacts. Cordiality and the co¬operative spirit marked the meeting and apparently no one had any serious grievances to air. Four motions were introduced and unanimously passed. The first, which was introduced by B. L. Sackett, was a recommendation by the delegates that a national committee be appointed to cooperate with Local Sections in the matter of student activities, to promote Institute welfare. It was agreed that this recommendation be made simultaneously to the Board of Directors and to the Mineral Industry Education Division. A subsequent resolution by A. M. Smith was passed asking that a part of the duties of this committee be to secure the opinions of Local Sections as to the most desirable methods of interesting students in the preparation of technical papers, by giving prizes or otherwise, and to report their findings at the Section Delegates' meeting next year.

Jan 1, 1933

By R. I. Jaffee, F. C. Holden, H. R. Ogden

ECENT papers dealing with the properties of unalloyed iodide titanium have been directed primarily at the determination of base-line properties for alloy investigations. Early work was limited to a few tests because of the limited availability of iodide titanium at the time. In the results of papers by Campbell et al.,1 Gonser and Litton,2 Jaffee and Campbell,3 inlay and Snyder,4 and Jaffee, Ogden, and Maykuth, data on mechanical properties are presented for unalloyed iodide titanium in the annealed and cold-worked conditions. Data are presented in this paper which show the effects of heat treatment on the structure and mechanical properties of commercially produced iodide titanium. Correlation is made between microstruc-tural variables and the mechanical properties. Experimental Procedures Melting Stock: The melting stock used was as-deposited iodide titanium, produced by New Jersey Zinc Co. The furnished analysis showed the following range of impurities: N, 0.004 to 0.008 pct; Mn, 0.005 to 0.013; Fe, 0.0035 to 0.025; Al, 0.013 to 0.015; Mo, 0.0015; Pb, 0.0045 to 0.0065; Cu, 0.0015 to 0.002; Sn, 0.001 to 0.01; Mg, 0.0015 to 0.002; and Ni, 0.003. Hydrogen content as determined by vacuum-fusion analysis was 0.0091 wt pct (0.44 atomic pct) after arc melting and fabrication. Nitrogen analysis on the arc-melted and fabricated titanium showed a content of less than 0.002 pct N. The average hardness of the furnished stock was Rf 70, or approximately 85 VHN. Melting Procedure: The as-deposited rods were rolled, sheared, and degreased in preparation for arc melting. The charge was arc-melted with a tungsten electrode in a water-cooled copper crucible under a positive pressure of high purity (99.96 pct) argon. The final ingot was approximately 2 in. in diameter and showed no increase in hardness over that of the initial stock. Fabrication: Heating for fabrication was done in air. It was begun by forging the ingot into a 3/4 in. diam rod, at an initial temperature of 1600°F. Scale was removed by sandblasting. The rod was then swaged to 1/4 in. diam at room temperature through a series of 20 dies, with approximately 10 pct reduction in area between each die. An anneal of 1 hr at 850 °C in air was given after the 1/2 in. die, such that the final cold reduction was 75 pct. Sections cut from this rod were used for test and microstructure specimens. Heat Treatment: Heat treatments were carried out in resistance tube furnaces with stainless-steel linings, under an atmosphere of gettered argon. As further protection against contamination, the specimens were packed in titanium turnings in a titanium sleeve. Control experiments have shown negligible hardness increases with this method, indicating that contamination from oxygen and nitrogen is slight. Three cooling rates were employed in this work; these have been designated as water quenching, argon cooling (to simulate air cooling under a controlled atmosphere), and furnace cooling. The cooling rate for an argon cool is 100°C per min for the first minute, with an average cooling rate of 35°C per min over a 15-min period. A furnace cool requires about 10 hr, with an average cooling rate of 3.6oC per min during the first hour, and an average cooling rate of 1.2°C per min over the 10-hr period. Microimpact Test: The specimen adopted was based on the cylindrical Izod Type Y specimen (ASTM, E23-41T). All dimensions were reduced to half scale, including the notch radius. Specifications are shown in Fig. 1. The specimen is held vertically in an adapter and broken as a cantilever beam. Impact tests were run on a constant-velocity (11.34 ft per sec) Tinius Olsen impact testing machine with a total available energy of 100 in.-lb. Tests were made to determine the correlation between this microimpact and the standard V-notch Charpy impact test. Curves showing impact energy as a function of temperature for both impact tests are plotted in Fig. 2. Transition temperatures, when they occur, are about the same for both impact tests. All three titanium-rich materials have the same conversion factor, 10. Tensile Testing: Tensile tests were conducted on Baldwin-Southwark testing machines using the 600, 2400, or 3000 1b range. Specifications for the test specimen were taken from the 1948 edition of the ASM Metals Handbook, and are shown in Fig. 1. Strain measurements were made using an SR-4 resistance gage (Type A-7) cemented to the reduced section in conjunction with a lever-type extenso-meter. Readings on the SR-4 strain indicator were

Jan 1, 1954

[ ]

Jan 1, 1938

By A. H. Larson, L. G. Twidwell

DURING the roasting of zinc sulfide concentrates and by-product recovery from flue dusts, the zinc sul-fate phase may occur in various stages of the processes. In addition to zinc sulfide, other sulfide phases are usually present such as CdS, PbS, CuzS, and FeS. Consequently, the effect of these sulfides on the thermal decomposition of ZnS04 was investigated. Merck high-purity, anhydrous zinc sulfate was used as the starting material. The sulfate was heated under an argon atmosphere, at a rate of 10°C per min. With the first slight indication of decomposition as determined by gas analysis, the sample was removed from the furnace and allowed to cool. X-ray patterns showed no other phase present. It is estimated that less than 0.05 pct of the ZnS04 decomposed. The metal sulfides were also heated under an argon atmosphere to drive off any adsorbed water. The materials were then sized (-200 to +270 mesh), mixed in predetermined mole ratios, and pressed into pellets. The experimental measurement of the reaction rate consisted of purifying the argon carrier gas, continuous flushing of the heated reacting mixture with argon, and collection and analysis of the SOn product gas. The reaction system was heated to 600°C and al-

Jan 1, 1967

W. P. WHITE,* Washington, D. C. (written discussion?).-The authors seem to have proved that for a phenomenon as irregular as the one they were investigating there was no perceptible conduction effect in the platinum wire. It should be mentioned, however, that the conduction of heat to and from small wires is not proportional to their surface and might give unexpected value, varying largely with the medium in which the wire was situated. Attempts to eliminate a conduction effect in the wire by extrapolating the curve obtained by using different sizes have in some cases given incorrect results, so that the authors' result should be applied with great care as a guide in other cases. The difference in size of wire employed by them is really rather small. If the desire had been to find out how great the effect was instead of merely to demonstrate its absence, a greater difference of diameter would, of course, have been selected. The sharp gradient immediately in front of the burning portion of the cigar is quite surprising at first sight. The weight of air coming from a flame is considerably greater than the weight of material burned, and it would be thought that this stream of heated air would heat very con-siderably the material not yet reached by the zone of combustion. Pos-sibly the heat is exhausted in evaporating moisture from the material. In that case the cigar is really a sort of regenerative furnace, except that it is not air but the, material which is preheated, and the pre-heating produces dryness rather than increase of temperature. Whether or not this is the case would be shown by finding how hot a thoroughly dry cigar would get.

Jan 12, 1919

By E. W. Davis

The mixing of fine ores with fuel and burning under induced draft is called sintering in iron-ore practice and either sintering or roasting in copper and lead metallurgy. The first development of sintering was the Huntington-Heberlein process, in which fine sulfide ores mixed with fuel were charged into a pot and burned under the action of an upcast current of air introduced at the bottom of the pot. Modern development has resulted in two types of machine; the continuous Dwight-Lloyd machine, which consists of heat-resisting grates and a moving beltlike type of hearth constructed of metal, in which air is drawn downward through the bed, and the stationary Greenawalt batch process, which operates in the same manner as the Dwight-Lloyd except that the hearth is stationary. The recent rapid increase in the use of sintering has been the result of two great advances in metallurgical process—flotation and the treatment of flue dust. The Dwight-Lloyd machine is used in many plants for agglomerating flotation concentrates and at the same time reducing the sulfur content to furnace requirements and it has become standard practice to treat iron blast-furnace flue dust by either the Greenawalt or Dwight-Lloyd machine, so that it can be recharged into the furnace. The mining of low-grade magnetite iron deposits and their beneficiat-ing by grinding and magnetic separation resulted in a fine concentrate extremely detrimental to blast-furnace practice. These concentrates are sintered and made into ideal material for blast-furnace use. Incidentally, coke savings of about 400 lb. per ton of pig are reported. Sintering at Evergreen Plant The application to limonitic iron ores is the most recent development of the sintering process. The first plant in the Lake Superior region was erected by the Minnesota Sintering Co., a subsidiary of the Evergreen Mining Co., at Ironton, Minn., in 1924. This plant was designed to treat Cuyuna Range iron and manganiferous ores containing low silica, high moisture and a structure objectionable because of a large proportion

Jan 1, 1930

By Henry Rawdon

THE following note describing the behavior of copper under rather unusual conditions is offered here for its suggestiveness rather than as a complete study of the question. The examinations described were made because of a request for information concerning the embrittlement of copper when heated in a molten salt bath (sodium chloride) for the purpose of cleaning it, as well as for softening it. It is well known that metals may be rendered very brittle by electrolytic action, in aqueous solutions, in all probability by the action of nascent hydrogen, and it was suspected that perhaps the embrittlement of the copper by means of the molten salt was produced in a somewhat similar manner. It was found that the copper was in contact with iron (or steel) while immersed in the molten salt, through the occasional use of an iron stirring rod, iron forceps for handling the pieces, and an iron pot for containing the fused salt. In the electrochemical potential series iron and copper stand some distance apart, copper being electronegative to the iron. Assuming that the two metals bear a similar relation to each other, when immersed in a bath of molten salt, as they do in an aqueous solution, they would be expected to form a galvanic couple, the copper being the cathode. By this means the copper might be embrittled, as often happens in aqueous solutions, by the action of the liberated hydrogen. In this case, however, the embrittlement must be attributed to some other agent than hydrogen. To demonstrate how copper may be embrittled under these conditions, two small rods, one of copper and the other of mild steel, approximately 3/8 in. (9.5 mm.) in diameter, were immersed in a bath of sodium chloride that had been heated somewhat above its fusion point (melting point of sodium chloride is 819° C.) and an electromotive force of approximately 6 volts from a storage battery was impressed upon the system. The copper was made the cathode and the action was continued for

Jan 2, 1920