Search Documents

By G. R. Leverant, M. Gell

The high- and low-cycle fatigue poperties of MAR-M200 directionally -solidified into columnar-grained and single crystal forms were determined at 1400" and 1700°F. These results were compared with the corresponding properties of conventionally -cast MAR-M200. The low-cycle fatigue lives of the columnar-grained and single crystal materials were similar at both temperatures and were one to two orders of magnitude greater than those of conventionally-cast material. The variations in the fatigue lives among the three forms of MAR-M200 were related to the more rapid rate of intergranular muck propagation compared to that of transgranular propagation. In conventionally-cast MAR-M200, cracks were initiated in grain boundaries and crack popagation occurred rapidly along an almost continuous grain boundary path. In the columnar-grained material, crack initiation occurred on short transverse segments of grain boundaries, but crack propagation was transgranular. The fatigue lives of columnar-grained and single crystal materials were approximately the same because most of the life in both materials was spent in trans-granular propagation. For the directionally -solidified materials, the number of cycles to failure, Nf, can be related to the total strain range, , by: heT = K where n and K are 0.16 and 0.044 at 1400'F and 0.29and 0.098 at 1700, respectively. In addition to intergranular crack initiation in the columnar-grained material, initiation also occurred at we-cracked MC carbides and micropores in both directionally-solidified materials. At 1400°F, fatigue life was reduced with increasing MC carbide size, but at 1700 there was no effect of carbide size. THE creep and stress-rupture properties of conventionally-cast nickel-base superalloys can be greatly improved by directional solidification into either single crystal or columnar-grained forms. The improvement in properties results from a reduction in intergranular cavitation and crack growth in the columnar-grained materials and the complete absence of this fracture mode in the single crystals. This paper describes the effect of grain boundaries on the elevated temperature fatigue properties of the nickel-base superalloy MAR-M200. The effect of cycling frequency on cracking arid fatigue life and the role of MC carbides and micropores on crack initiation are also emphasized. The fatigue properties of columnar-grained and single crystal MAR-M200 at room tem- perature,4,5 and the change in the mode of fatigue crack propagation with temperature6 have recently been described. I) EXPERIMENTAL PROCEDURE The material used in this study was the nickel-base superalloy MAR-M200, directionally-solidified into columnar-grained and single crystal forms. The columnar grains were approximately 0.5 mm in diam. The nominal composition of these materials in wt pct was 0.15C, 9Cr, 12.5W, loco, 5A1. 2Ti, lCb, 0.05Zr. 0.015B, bal Ni. They were solutionized for 1 to 4 hr at 2250°F followed by aging at 1600°F for 32 hr. which resulted in 0.2 pct offset yield stresses of 150,000? 144,000, and 95,000 psi at room temperature? 1400°, and 1700°F, respectively. The corresponding elastic moduli parallel to the testing direction were 19.2. 15.0, and 12.5 x 106 psi, respectively. Specimen design, testing procedures and alloy mi-crostructure have been described previously and will only be summarized here. Following the 1600°F aging treatment. MAR-M200 contains an ordered, cuboidal, y' precipitate 0.3 1 on edge, which is coherent with the 1 matrix. The y' precipitate is quite stable; even after testing at 1700°F. the precipitate is only slightly enlarged and its corners somewhat rounded. The alloy also contains a small volume fraction of micropores, and MC carbides. some of which contain preexisting cracks5 formed during casting. These cracks are always parallel to the long dimension of the carbide. Measurement of MC carbide size has been described previously.5 Axial fatigue tests were conducted in air over a wide range of strain amplitudes in both the high - and low-cycle fatigue regions, with specimen lives varying from about 10' to 10' cycles. Low-cycle fatigue (LCF) tests were strain-controlled with strain varied between zero and a maximum tensile value at a frequency of about 2 cpm. High-cycle fatigue (HCF) tests were stress-controlled with the stress varied between 5000 psi and a maximum tensile value less than the yield stress at a frequency of either 10 cps or 0.033 cps (2 cpm). The temperature in the gage section was controlled to 52°F. Specimen axes were within 5 deg of the [001] growth axis of the single crystals and the common [001 ] growth axis of the columnar-grained material. Specimen gage sections were electro polished prior to testing. After the standard heat treatment, three specimens were coated with a typical aluminide coating applied as a slurry. An additional specimen was given the coating heat treatment without actually being coated. In all cases: specimens were reaged at 1600°F for 32 hr after receiving the coating heat treatment at 1975'F for 4 hr.

Jan 1, 1970

By W. H. Bassett

BERYLLIUM was discovered in 1798 by Vauquelin and the metal was first produced by Wohler in 1828 about a year later than his production of metallic aluminum. Beryllium remained dormant until about 1920 when the production of the metal by the electrolysis of a molten bath was carried out by Stock in Germany, closely followed by Dickinson in the United States and by Vivian in England. This may not have been the first time the electrolytic method was thus used but was the beginning of present-day methods. I believe the first commercial attempts in this country started with the Kemet Laboratories about 1924. Siemens & Halske in Germany were working on the same problem at about the same time. The work of the Kemet Laboratories was transferred to the Beryllium Company of America and later to the Beryllium Development Corporation. In 1926 1 made a considerable study of the beryllium¬copper alloys, using beryllium purchased from the Beryllium Company of America, and read a paper on this subject at the February, 1927, meeting of the A.I.M.E. However, I failed at that time to discover the properties of precipitation hardening which such alloys have in a very marked degree. After this publication the work on beryllium-copper alloys rested awhile. One cause for this was the difficulty of securing a supply of beryllium-at least at what might be considered a reasonable price. In 1926 the price was $200 per lb., a figure which held about the same both in this country and in Germany until the beginning of 1932, when it was offered here at $50 per lb. if taken in the form of a copper alloy which carried about 121/2 per cent beryllium. Somewhat later the 121/2 per cent alloy dropped to $25 per lb. of beryllium contained, which is the present price. Promise is made that with a greater consumption, production on a larger scale warrants a reduction in price to $10 per pound or less.

Jan 1, 1933

By AIME AIME

READERS of a technical paper, or the audience if the paper is presented orally, judge the paper on several counts. The September 1940 issue of MINING AND METALLURGY contained an excellent short article by S. Marion Tucker en- titled "Are You Going to Present a Paper," which considered the general subject of presentation. In it Dr. Tucker referred to the large number of poorly prepared and badly delivered papers that are presented annually before the large number of technical and other societies that meet regularly, and he stressed the point that good delivery, length of paper, content, and composition are of great importance. All of Dr. Tucker's points were well taken; however, good illustrations are equally important in explaining certain phases of some papers.

Jan 1, 1941

Adams, Benjamin C., Jr., Student, Univ. of Oklahoma Norman, Okla. '36 Adams, Ernest C., Student, Univ. of Illinois 908 W. Green St., Urbana, Ill. '35 Adams, George H., Student, Colorado School of Mines Golden, Colo. '36 Adams, Robert Keller Mitchell Hotel, No. 18, Golden, Colo. '35 Afshar, Hadji Khan A., Student Box 63, Univ. Sta., Moscow, Idaho. '36 Ahrenholz, Herman William, Jr., Student, Lehigh Univ Bethlehem, Pa. '35 Alger, Robert P., Student, Missouri School of Mines & Met.Rolla, Mo. '36 Allen, Paul W., Student, Mass. Inst. of Tech Cambridge, Mass. '35 Allen, R. M., Jr., Student, Virginia Polytechnic Inst., "G" Co.Blacksburg, Va. '35 Alley, John Arnold, Student, Montana School of Mines Butte, Mont. '36 Amberger, R. H., Student, Michigan College of Min. & Tech Houghton, Mich. '35 Ambrosiani, F. Peter, Student, Michigan College of Min. & Tech Houghton, Mich. '36 Andersen, Burton Lee, Student, School of Mines, Univ. of Washington Seattle, Wash. '36 Anderson, Carlos, Student, Univ. of Oklahoma Norman, Okla. '36 Anderson, J. Wendell, Student, Pennsylvania State College State College, Pa. '36 Anderson, Joseph S. Cornelia Hotel, Ajo, Ariz. '35 Anderson, R. C., Student, Univ. of Washington Seattle, Wash. '35 Anderson, Roy A., Student, Washington State College Pullman, Wash. '35 Anderson, Willard. Student. Univ. of Oklahoma Norman, Okla. '36

Jan 1, 1936

By Herbert Hoover

I HAVE been greatly honored as your unanimous choice for President of this. Institute, with which I have been associated during my entire professional life. It is customary for your new President, on these occasions, to make some observation on matters of general interest from the engineer's standpoint. The profession of engineering in the United States comprises not alone scientific advisers on industry but, in great majority, is comprised of the men in administrative positions. In such positions, they stand midway between capital and labor. The character of your training and experience leads you to exact and quantitative thought. This basis of training in a great group of Americans furnished a wonderful' recruiting ground for service in these last years of tribulation. Many thousands of engineers were called into the army, the navy, and civilian service for the Government. Thousands of high offices were discharged by them with credit to the profession and the nation. We have in. this country, probably, one hundred thousand professional engineers. The events of the past few years have greatly stirred their interest in national problems.' This has taken practical. form in the maintenance of joint committees for discussion of these problems and support to a free advisory bureau in ,Washington. The engineers want nothing for themselves from Congress.. They want efficiency in government, and you contribute to the maintenance of this bureau out of sheer idealism. This organization for consideration of national problems has had many subjects before it, and I propose to touch on some of them this evening.

Jan 1, 1920

By J. F. Smith, J. E. Davison

The heat capacity of CaMg2 was measured over the temperature interval, 4.8° to 287°K, by the technique of low-temperature adiabatic calorimetry. Heat content measurements were performed with a drop calorimeter over the temperature interval, 273" to 673°K. From these data the thermodynamic functions, (FT - H0)/T, ST - So, and & - Ho, were evaluated. A third-Law calculation of the standard entropy of formation of CaMg2 yields a value of -0.25 * 0.06 cal per (°K g-atom) , and the free-energy function derived from this study when combined with existing equilibria data yields a value for the standard enthalpy of formation which is in agreement with direct calorimetric enthalpy measurements. The accompanying paper' shows that the enthalpy of formation of CaMg2 has been determined with good precision by three different calorimetric techniques.'-= TWO independent determinations of the Gibbs free energy of formation of CaMg2 have also been made; both determinations were based on vapor pressure measurements, being in one case hydrogen vapor pressures over ternary Ca-Mg-H alloys4 and in the other case magnesium vapor pressures over binary Ca-Mg alloys.5 The present determination of heat capacity of CaMg2 below room temperature and of the heat content of CaMg2 above room temperature was undertaken to provide supplementary data. These data are useful in their own right but can in addition be used to evaluate an entropy of formation for CaMg2 which, because of the interrelation of free energy, enthalpy, and entropy, can be used as a check of the self-consistency of the composite of the presently available information. LOW-TEMPERATURE HEAT CAPACITY The heat capacity of CaMg2 was measured over the temperature interval 4.87° to 286.64°K in an adiabatic calorimeter. The physical details of the calorimeter and the experimental procedure for measuring the heat capacity of a specimen have been adequately described by Gerstein et a1.6 The source and purity of the calcium and magnesium are described together with the methods of sample preparation and chemical analyses in the accompanying paper.' Results of chemical analyses of the material which was used in the present investigation are shown in Table I. These analyses show that, on the basis of the published phase diagram,7 the heat capacity sample contained a slight excess of a calcium while the heat content sample contained a slight excess of magnesium. However, in both cases the excess was small, and X-ray diffraction patterns showed reflections which were without exception attributable to CaMg2. The sample which was used for heat capacity measurements weighed 69 g while the sample container and addenda weighed 132 g. The sample was in the form of annealed powder, 50 to 60 mesh, and was sealed into the sample container under 0.1 atm of helium. Copper fins inside the sample container facilitated thermal equilibrium of the powdered Sample. Time intervals of the order of 10 min were required for thermal equilibration, and such times are normal for this calorimeter regardless of the form of the sample. The observed heat capacities were corrected for the small excess of a calcium through use of the heat capacity values tabulated by Hultgren et a1.8 The corrected heat capacities are tabulated as a function of temperature in Table II. The free-energy function and the absolute entropy of CaMg2, which were calculated from the experimental heat capacity data, are listed in Table 111. A smooth curve was fitted to a plot of the experimental values of the heat capacity and in only two instances above 30°K did the plotted points deviate from the curve by more than 0.2 pct. Below 10°K the deviation of several of the points was as much as 50 pct. These large percentage deviations were attributed to the small value of the heat capacity and to the low sensitivity of the platinum resistance thermometer in this temperature range. The deviations in the region of 10°to 30°K were less than 5 pct. Although the percentage deviations of some of the low-temperature measurements are large, the actual value of these deviations is small since the magnitude of the heat capacity in that temperature range is small. The error in the value of the third-law entropy at 298.15°K was estimated to be less than 0.01 cal per (°K g-atom). A value of -0.25 ±0.06 cal per (°K g-atom) was obtained for the standard entropy of formation at 298.15°K from the relation:

Jan 1, 1969

By W. W. Odell

Once it was believed that anthracite or coke were the only fuels generally available and suitable for the generation of water gas, particularly so when this gas was made in the generators of standard carburetted water-gas sets such as are commonly used in the manufacture of city gas. During the past 8 years, practice has changed considerably and it is now common to find gas plants operating without anthracite or coke and using bituminous coal in the generator. This change in fuel has appreciably increased the marketability and sales of certain coal producers' products; accordingly it is of interest to coal operators and others to know the reason for this change, the present trend in practice and the adaptability of various coals for generation of water gas. This paper briefly discusses these conditions and some of the factors relating thereto. Bituminous Coal not Ideal but Cheaper than Coke In spite of many changes which have been made in both process and generating apparatus for using bituminous coal as generator fuel more efficiently, in general it is not an ideal fuel for this purpose. It is supplanting coke because it costs less; it is so much cheaper per ton delivered at the gas works that water gas made therefrom costs less per unit-volume than that made from coke, even though the quantity of generator fuel consumed per therm (100,000 B. t. u.) of gas made is greater with coal. This is the reason why so many city gas plants, as well as others, are using bituminous coal instead of coke. Conditions Favoring Change from Coke to Coal The conditions which have made it possible and feasible, as well as economical, to supplant coke with coal may be summarized as follows: (1) Changes in methods of operating and alteration in generating apparatus; (2) lowering of the calorific standards for city gas, and (3) availability

Jan 1, 1927

By Herbert Clark Hoover, Lou Henry Hoover

GEORGIUS AGRICOLA was not only the author of works on Mining and allied subjects, usually asso ciated with his name, but he also interested himself to some extent in political and religious subjects. For convenience in discussion we may, therefore, divide his writings on the broad lines of (1) works on mining, geology, mineralogy, and allied subjects; (2) works on other subjects, medical, religious, critical, political, and historical. In respect especially to the first division, and partially with regard to the others, we find three principal cases : (a) Works which can be authenticated in European libraries today ; (b) references to editions of these in bibliographies, catalogues, etc., which we have been unable to authenticate ; and (c) references to works either unpublished or lost. The following are the short titles of all of the published works which we have been able to find on the subjects allied to mining, arranged according to their present importance :-De Re Metallica, first edition, 1556; De Natura Fossilium, first edition, 15,46 ; De Ortu et Causis Subterraneorum, first edition, 1546; Bermannus, first edition, 1530 ; Rerum Metallicarum Interpretatio, first edition, 1546; De Mensuris et Ponderibus, first edition, 1533; De Precio Metallorum et Monetis, first edition, 1550 ; De Veteribus et Novis Metallis, first edition, 1546; De Natura eorum quae Effluunt ex Terra, first edition, 1546 ; De Animantibus Subterraneis, first edition, 1549. Of the " lost " or unpublished works, on which there is some evidence, the following are the most important:-De Metallicis et Machinis, De Ortu Metallorum Defensio ad Jacobum Scheckium, De Jure et Legibus Metallicis, De Varia Temperie sive Constitutione Aeris, De Terrae Motu, and Commentariorum, Libri VI. The known published works upon other subjects are as follows:-Latin Grammar, first edition, 1520; Two Religious Tracts, first edition, 1522; Galen (Joint Revision of Greek Text), first edition, 1525 ; De Bello adversus Turcam, first edition, 1528 ; De Peste, first edition, 1554. The lost or partially completed works on subjects unrelated to mining, of which some trace has been found, are:-De Medicatis Fontibus, De Putre¬dine solidas Partes, etc., Castigationes in Hippocratem, Typographia Mysnae et Toringiae, De Traditionibus Apostolicis, Oratio de rebus gestis Ernesti et Alberti, Ducum Saxoniae.

Jan 1, 1950

By E. J. McKee

THE area discussed lies south of Canadian River in Hutchinson County, Texas, covering approximately 10 m. east and west and 4 m. north and south. Development is carried on in the manner usual in standard tool operations. No outstanding divergence from the usual methods is necessary as wells are completed in 35 to 55 days to approximately 3000 ft. Most of the time is lost in the upper part of the hole and is usually caused in driving pipe of larger sizes. After approximately 1500 ft., little trouble occurs. A comparison of 13 contractors drilling for Phillips Petroleum Co. gave the following averages: Drilling time from 32 to 63 days with a daily footage of from 49 to 87 ft. per day. The rigs furnished are National turnbuckle type with 6-in. irons and steel wheels.

Jan 11, 1926

By B. L. Sackett

LEAD smelting has been an important industry in Utah for many years. The first lead smelting was done, over 60 years ago, at the Rollins mine in Beaver County, by burning heaps consisting of alternate layers of wood and high-grade carbonate ore. The lead thus obtained was. molded into bullets. With the development of. the mines, the problem of cheaper handling of the ore became important. The only outlet for this ore was Swansea or the Atlantic Coast but to ship to either cost $150 per ton or more for treatment and handling. From 1864 to 1871, experimenting was done with blast, Scotch hearth, and reverberatory furnaces, with the blast furnace surviving as, the standard plant. The first crude furnaces were circular or hexagonal in shape, and were made of adobe and stone, which quickly burned out. They were small, about 2 1/2 ft. in diameter, and smelted from 3 to 10 tons. in 24 hr. The metal had to be tapped from the bottom of the crucible, necessitating a shut down of the furnace during this process. This pro¬cedure caused salamanders to form around the tap hole when the furnace was started again, which frequently resulted in freezing. The campaign lasted until a tap of bullion was made. The first successful plant of the crude stone type was operated in 1870. From 1870 to 1872, there was a smelter building craze in the state. During that period, about 20 furnaces were built, chiefly near the mines, and their operation was limited and sporadic. The work was then placed in the hands of trained metallurgists, who standardized on the rectangular form of furnace. In 1871, Daggett, at the Winnamuck mine in Bingham, installed water-jackets around the smelting zone of the furnaces. These furnaces were circular; the diameter at the tuyere line was 3 ft. 6 in. and at the charge floor 5 ft. 3 in. The height from tuyere line to charge floor was 14 ft., height of tuyere line above top of crucible was 3 ft. 8 in. Fur-

Jan 8, 1925

By C. F. Floe, M. Cohen, M. B. Bever, V. G. Paranjpe

NITROGEN is becoming recognized as one of the important elements in ferrous physical metallurgy. Several investigations indicate that nitrogen plays a significant part in such phenomena as strain aging and temper brittleness. Nitrogen is known to be a powerful austenite stabilizer and may be a useful alloying element in stainless steels. The hard-enability of steels has been found to be increased by nitrogen. The nitriding and carbonitriding pro- cesses are examples of successful industrial application of nitrogen in ferrous materials. For a complete understanding of the various roles played by nitrogen in ferrous metallurgy a knowledge of the phase relations in the binary iron-nitrogen system is essential. The literature contains a variety of iron-nitrogen phase diagrams. Those suggested by Fry, Sawyer,² Epstein and his coworkers,³,4 Lehrer,5 Eisenhut and Kaupp, and Hägg7,8 differ significantly from one another. Moreover, the most recent of these investigations dates back about twenty years. A re-determination of the entire diagram, therefore, appeared desirable. In addition to the published phase diagrams, investigations have been carried out on portions of the iron-nitrogen system. Bramley and Haywood determined the composition and temperature of the iron-iron nitride eutectoid. The maximum solubility of nitrogen in a iron was investigated by Portevin and Seferian10 and by Diikstra. 11 Several investigators have determined the crystal structure of the various iron-nitrogen phases. In fact, Eisenhut and Kaupp6 and Hägg7 based their entire phase diagrams on the results of such studies. Epstein' and Emmett12 reported lattice-parameter measurements on the E (hexagonal close-packed) phase. Osawa and Iwaisumi13 also studied the change in lattice parameters of the a, ? and E phases with nitrogen content. Brill" and Hägg7 showed that the y' phase has an ordered structure, and Hendricks and Kostingsl5 suggested a structural relation between the E and phases. In a recent investigation Jackl6 arefully studied the super-lattice reflections from the y' and phases. Experimental Procedure A large variety of experimental methods has been used by previous investigators in studying the iron-nitrogen system. These methods include thermal analysis, microscopic examination, X ray diffraction, magnetic measurements, dilatometric analysis and anelastic experiments. Thermal analysis is of low accuracy in determining changes in the solid state. This accuracy is further decreased for iron-nitrogen alloys since composition changes will occur during heating or cooling unless extreme care is taken to use a proper atmosphere. Metallographic methods are of small value . because homogeneous iron-nitrogen alloys of sufficient size can be produced only with great difficulty. The dilatometric method is open to the same objections as thermal analysis in that changes in composition may occur during heating and cooling. Lattice parameter measurements by X ray diffraction can be used satisfactorily for determining phase boundaries if cooling is fast enough to prevent structural changes. In view of the limitations of the various other techniques two methods only were adopted in this investigation, (1) X ray diffraction measurements, and (2) a controlled nitrogenizing method. The second method is an innovation for investigating the iron-nitrogen system, and will be described at length. Materials: All iron-nitrogen alloys were prepared from carbonyl iron powder of the analysis shown in table I. The average particle size was about 20

Jan 1, 1951

By Stefan Boshkov, Malcolm T. Wane

The validity and accuracy of velocity measurements underground have been questioned repeatedly by those in mine ventilation work. The general disagreement on the subject is well illustrated in an AIME publication.' Although the presence of errors is readily admitted, their magnitudes are not known and often are described by practical operators merely as "great," "small," or "of no importance." The belief that errors are of academic interest only prevails because of a justifiable claim that actual volumes of air circulated are well in excess of those required by law and safe mining practices. Poor understanding of the source and nature of errors inherent in velocity measurements, coupled with questionable determination of cross-sectional area, result in faulty techniques for the purpose of expediting ventilation surveys and render doubtful the calculated volume. Often consistency of readings is confused with accuracy. A succession of check readings showing a maximum deviation of 5 pct in the measured value of velocity usually signifies nothing more than diligent application of technique in a stable ventilating current.

Nov 1, 1955

By AIME AIME

SINCE the preparation of the Fall Meeting announcement the Montana Section has extended an invitation to the members traveling to Spokane to make at least a short stop at Butte, en route. Accordingly, the train schedule below has been worked out as an alternative to that announced in the general circular. This will permit a half day in which to visit either mines at Butte or the smelter at Anaconda and an opportunity for an evening meal with our Montana members. An interesting time is assured either way and the chance to renew acquaintance with Butte friends will be well worth will

Jan 1, 1929

By Edward A. Loria

Vanadium is one of the materials being considered for use in fast-breeder nuclear reactors. It is a good heat conductor and nearly transparent to radiation, properties regarded as ideal for nuclear fuel containers. The problem has been the metal lacks ductility needed for forming. In our program at Reno Laboratory the effects of the U.S. Bureau of Mines (previous affiliation) the effects of oxygen, nitrogen, and carbon have been reported21,22 nd most recently the effects of boron and boron with carbon.23 The continuing study by the Ames Laboratory of the effects of hydrogen, the most subtle and fugitive element in its relationship to structure and properties, is commendable. The solubility of oxygen, nitrogen, and hydrogen in vanadium (and other bcc metals as well) is related to material purity. With the available limit on metal purity and the interaction (clustering) of hydrogen with the other interstitial and substitutional elements present in their base metal, would the authors comment on the tolerance of hydrogen in relation to oxy- gen that will avoid intergranular fracture and above what content or how seriously harmful in oxygen at various carbon levels? Understanding the true effects of hydrogen (and other interstitial impurities) in vanadium depends on knowledge of the amount present under various conditions and its distribution between various possible positions. Significant amounts of hydrogen may be in "thermo-dynamic" solution, but not as individual atoms in interstitial positions. It may be in grain boundaries, in subgrain boundaries, in vacancies, or in dislocations. Some of the hydrogen may be paired or in complexes with impurities in substitutional solid solution in vanadium. This makes the analysis of the effect of hydrogen vastly more difficult. It should not be expected that hydrogen in grain boundaries will affect slip in the same manner as hydrogen in interstitial positions, nor will the complexes react to heat treatment the same way as hydrogen in dislocations. It is gratifying that the authors have quoted results from two of our inestiations,' but neglected one2' which applied the Petch theory to electrorefined vanadium of high purity and analyzed the effects of oxygen, nitrogen, and carbon on the ai and ky values obtained by the extrapolation and grain size methods. Details can be found in the paper. Briefly, we obtained a ui value of 10,300 psi (t = 5150 psi) at 273°K. The metal also exhibited profuse twinning with high ductility at 123" and 77°K. Nitrogen was more effective than oxygen in increasing ui, the increase being about twice as much for the same impurity level. Carbon additions resulted in only minimal changes in Ui. The corresponding ky increased as oxygen and nitrogen increased, with nitrogen being more effective. Carbon additions resulted in little change. Although the difference in yield strength of vanadium was explained on the basis of the Cottrell-Bilby model of the tearing away of dislocations from the impurity atoms,

Jan 1, 1970

Following closely Marcona Corp.'s announcement of its new Marconaflo process for transporting mineral slurries by ship (see pp. 96-97, Sept. 1969 [ ]), Midland-Ross Corp. (M-R) now heralds its metallized iron pellet process which supplements Oregon Steel Mills1 (Oregon Steel) new Portland, Ore., plant. Harry J. Bolwell, president of M-R describes the company's M-R Pellet as "the most exciting advance in steelmaking in a decade, one which will profoundly affect the industry." In fact, other knowledgeable industry spokesmen believe that with these developments the mini-steel plant era is now here and that this technical development along with the Marconaflo process will revolutionize iron ore shipments and steelmaking. The M-R president predicts that electric furnaces can account for 20% of the annual U.S. steel production by 1975, compared with 14% at the present time because of these developments.

Jan 12, 1969

By W. E. Rice

THE ceramic industry has to do with forming or molding articles of clay, and imparting to them their characteristic properties of permanence, strength and color by subjecting them to heat treatment in kilns. This heat treatment is commonly known as "firing" or "burning." The art of firing clay ware antedates the industrial use of coal; hence wood was the fuel first used, and the earliest kilns were built to burn wood. The majority of the clay ware produced today is fired in periodic kilns that are essentially enlarged structures similar to the earliest enclosed kilns; a kiln consists of a large chamber 16 to 32 ft. dia. (or rectangular) in which the ware is charged and fired either in direct contact with flame or hot gases from the fuel, or in saggers which shield the ware from direct contact with the gases. The fuel is burned in a number of small furnaces built in the thick .wall that encloses the chamber; these furnaces are from 16 to 36 in. wide and from 3 to 5 ft. long; some of them have horizontal or sloping grates, but many have no, grates; the last are called "dead-bottom" furnaces. The temperature necessary to mature the charge in the kiln varies for different clays; for some it is as low as 1800°, and for others as high as 2700° F. Wood was an ideal fuel for the low temperatures that were used in early kilns; it burns freely and produces along, clean flame, which promotes uniform distribution of the heat in the kiln; it does not coke and so restrict the passage of air through the fuel bed; the ash does not melt in the fuel bed to form clinker; and the ash that is carried into the chamber and deposited on the charge does not contain iron and sulfur to discolor the clay. The extent of the ceramic industry now precludes the general use of wood in kilns, so that today this industry is one of the large users -of bituminous coal, burning more than eight million tons annually in kilns. Manufacturing plants usually are at or near the source of clay, with deposits of coal suitable for kilns occurring near the clay. The cost of coal is the largest single item of expense in the manufacture of clay ware, and, because all coals are not equally suitable for the process, the careful selection of coal is important. In this selection the desidera-

Jan 1, 1932

By N. H. Jensen, B. L. Sackett, Carlos Bardwell, Simon Jacobson

Lead smelting has been an important industry in Utah for many years. The first lead smelting was done, over 60 years ago, at the Rollins mine in Beaver County, by burning heaps consisting of alternate layers of wood and high-grade carbonate ore. The lead thus obtained was molded into bullets. With the development of the mines, the problem of cheaper handling of the ore became important. The only outlet for this ore was Swansea or the Atlantic Coast but to ship to either cost $150 per ton or more for treatment and handling. From 1864 to 1871, experimenting was done with blast, Scotch hearth, and reverberatory furnaces, with the blast furnace surviving as the standard plant. The first crude furnaces were circular or hexagonal in shape, and were made of adobe and stone, which quickly burned out. They were small, about 21/2 ft. in diameter, and smelted from 3 to 10 tons in 24 hr. The metal had to be tapped from the bottom of the crucible, necessitating a shut down of the furnace during this process. This procedure caused salamanders to form around the tap hole when the furnace was started again, which frequently resulted in freezing. The campaign lasted until a tap of bullion was made. The first successful plant of the crude stone type was operated in 1870. From 1870 to 1872, there was a smelter building craze in the state. During that period, about 20 furnaces were built, chiefly near the mines, and their operation was limited and sporadic. The work was then placed in the hands of trained metallurgists, who standardized on the rectangular form of furnace. In 1871, Daggett, at the Winnamuck mine in Bingham, installed water-jackets around the smelting zone of the furnaces. These furnaces were circular; the diameter at the tuyere line was 3 ft. 6 in. and at the charge floor 5 ft. 3 in. The height from tuyere line to charge floor was 14 ft., height of tuyere line above top of crucible was 3 ft. 8 in. Furnace capacity was about 14 tons per day, with a campaign of about 16 days. Cost of smelting was about $44 per ton. The ores making the

Jan 1, 1926

By Charles Will Wright

THOSE that attended the seventeenth International Geological Congress held in Russia last summer had an excellent opportunity to gather data and to form impressions on the progress made in the industrialization of the country, particularly with regard to the mineral industries. Several trips to places of interest were arranged, supplementary to the technical sessions held in Moscow, the one to the Ural region being that which I selected as being most likely to be of interest. The accomplishments of the last decade in opening up new mines and building new metallurgical plants in the Soviet Union have been outstanding. This could only be accomplished by a central government ready to employ the best technical talent, which was

Jan 1, 1937

By George C. Branner

BAUXITE is produced in Arkansas from two mining districts in the central portion of the State. These are (1) the Fourche Mountain district, immediately south and southeast of Little Rock in Pulaski County, and (2) the Bauxite (town) district, about five miles east of Becton in the eastern part of Saline County. These two mining districts are about twelve miles apart, separated by territory which, so far, has produced a negligible amount of commercial ore. Mining was by open-pit methods exclusively until 1924, when underground methods came into use. From 1924 to 1930 about 40 per cent of all of the ore produced in Arkansas was mined by underground methods, mainly by retreating caving.

Jan 1, 1935

By J. L. Bruce, G. W. Nicolson

ThE country rock of the Mavrovouni mine of the Cyprus Mines Corp. is hydro-thern~ally altered, disintegrated pillow lava, with very little tensile strength ("short" ground). In places, especially when wet, it is heavy ground, though not extremely heavy except where movement has been caused by underlying or nearby stoping operations. Damage by caving from roof or sides of galleries is not sudden but progressively faster when the size of the cave increases as a result of the fall of small pieces. CeMent and Concrete Linings During early operations, galleries in the country rock were supported by customary mine-timbering methods. Available timber, howcver, was of poor quality and of relatively high price, and replacements were frequent and expensive. Furthermore, the massive sulphide ore bodies required large volumes of fresh air for ventilation and cooling, and it was therefore desirable to provide smooth-lined galleries with low resistance for the introduction of air to the ore bodies. It was also desirable to eliminate hazards of fire in shafts and underground workings insofar as this would be practical. Cement and concrete were relatively cheap, and plans for using these in support of shafts, underground galleries, raises, and chutes, were developed steadily. Circular shafts with diameters ranging from 10 to 15 ft were adopted for all permanent shafts and airways. In places these were lined with concrete poured behind sectional pressed-steel forms especially constructed for this purpose. In other places, they were lined with precast-concrete blocks. It was found that such precast concrete of good quality could be produced on mass production scale and delivered at the mine from most favorable point of manufacture, at a cost of about 25 cents per cubic foot of concrete. This refers to prewar costs. As the use of concrete blocks in circular lined galleries was developed, it was found that there were very great advantages in the reduction of air resistance as compared with customary timber supports. After best methods had been developed, it was found that breakage and replacements were extraordinarily low, averaging only about 11\2 pct per year during a period of about 15 years. Furthermore, it has been possible to reclaim for re-use a very large percentage of the concrete blocks from abandoned galleries. During the history of the operations precast-concrete blocks have been used for lining shafts, raises, ore chutes, galleries, and shaft stations, ranging from 3 to 16 ft id. The thickness of lining has varied from 5 to 10 in.; with 12 in. thickness in a few cases. Junctions of two galleries at angles ranging from about 30 to 60° are usually made of poured concrete behind sectional forms, or of a combination of poured concretc and precast blocks. In nearly all cases it has been found advisable to make the point of the wedge at the junction, of

Jan 1, 1949