Search Documents

By W. F. Boericke

NOT the least interesting sights that New York has to offer the visiting mining engineers are the extensive tunnel operations that are being pushed in connection with the subway construction. While a "hard rock" man might feel at home on these jobs, the engineers driving the subway tunnels have necessarily had to encounter some new problems pe-culiar to the largest permanent mining camp in the country. To drive a heading 36 by 18 ft. in hard rock, with a station section to follow 52 by 27 ft. across-and to do it in the midst of a city's traffic-demands engineering skill of a high order. Not the least of the problems overcome by the engineers in charge was to provide adequate ventilation for the men at the face at all times, so that there would be no delay in the work. With a crew of 40 men (32 drill runners and helpers on the machines alone, working two shifts) a hold-up due to inability to get back promptly to the face after shooting would affect costs quickly. AIR VITIATED BY EXHAUST FUMES FROM MOTOR TRUCKS A complication not encountered by metal miners, but which the subway engineers had to meet, was pollution of the air in the tunnels by fumes from the exhaust of the motor trucks used to haul away the broken rock. As shown in the cut, motor trucks were constantly em-ployed to remove the heavy tonnage broken as the tun-nels went ahead, amounting, according to R. J. Van Wagner, chief engineer of the Del Balso Construction Co., to 48 cu. yd. per ft. of tunnel advance. As the length of the tunnel under his management was 900 ft., it was essential for the safety of the men that suffi-cient air be introduced to dilute the poisonous fumes so that no ill effects would be felt for the entire distance that the trucks had to travel. The presence of the ex-haust fumes was especially noticeable on foggy days.

Jan 2, 1928

By D. E. Moore

The strength of a natural serpentinite gouge was measured at 400°C and an effective pressure of 100 MPa. The strength of the gouge decreased with increasing pore pressure to 50 MPa and then was nearly constant between 50 and 125 MPa. The samples at 50-125 MPa pore pressure slid stably, whereas those at 3-25 MPa pore pressure showed stick-slip behavior. Lengthening the pre-heating time to 72,000 s of samples at 100 MPa pore pressure led to increases in both the strength and the likelihood of sliding unstably. With still longer pre-heating times, the strengths decreased again and sliding once more became stable. The strength of the gouge at 3 MPa pore pressure was unaffected by changes in pre-heating time. A possible explanation for the results is that excess pore pressures are being generated in the gouge, causing the true effective pressure to be lower than the apparent value.

Jan 1, 1984

By Joseph E. Pogue

THERE are two methods employed in the development of oil pools. The older and dominant method is one in which the primary object is the protection of the underground deposit from drainage through competing wells, and considerations of efficiency of extraction and cost of production are subordinated thereto. The newer and less prevalent method is one in which maximum efficiency and minimum cost are the first objectives and developments to these ends may proceed undisturbed by the exigencies of competitive drainage. The second method has developed mainly in pools under single ownership and the term "unit operation" has come to be applied to this procedure. A single ownership, however, is not essential to the method, for unity of operation may be achieved by agreement under split ownership, or even by a concert of enlightened purpose. There are examples of unit operation where neither the ownership nor the management is a unit, but merely where unity of procedure has been attained, as is the case of the Yates pool. .Throughout this paper unit operation is used in its broad sense without implying sole ownership or single management, although unit operation is more conveniently attained where these conditions are present.

Jan 1, 1930

By J. R. Lucas, R. L. Frantz

Mine sealing programs for the alleviation of acid mine drainage were begun by the Federal Government in the '30's. As part of an acid mine research project to The Ohio State University, a field test was undertaken to determine the effectiveness of mine seals for reducing mine acid. Details of the tests made at the McDaniels mine show the feasibility of air-sealing and flooding an acid-producing drift coal mine. Work by the University continues. The Federal Government undertook in the early thirties an extensive mine sealing program for the alleviation of acid mine drainage. In the states of West Virginia, Ohio, and Pennsylvania many general summaries have been made on this program but no critical evaluation with supporting data has been found on the effectiveness of mine seals for reducing mine acid. Because of this it was decided to undertake a field testing program as part of an acid mine research project of the Engineering Experiment Station, The Ohio State University. The objective of this phase of the project was to develop and install a field research laboratory for acid mine drainage studies. Specifications for such a mine laboratory were developed and resulted from the following considerations: 1) Size and preservation—the test mine shou1d be of limited size to permit frequent and detailed examinations; it should be in a reasonably sound condition to permit safe entry. 2) Isolation—the mine should be physically separated from all other mines. 3) Openings—a minimum number would be desirable to reduce the sealing problem. 4) Structure—the mine especially near the openings should be structurally sound. 5) Acid production—the mine should be producing significant quantities of acid. After considerable searching, the McDaniels mine was selected in the Hocking coal field in Vinton County just above Lake Hope State Park in southeastern Ohio. The small drift mine in the middle Kittaning coal consisted of two small rooms with one mine opening about 6 ft above a seasonal stream bed. Before it was finally decided to seal the mine, a short study was made of the acid drainage over several months. Fig. 1 shows a plot of acidity (milligrams per liter), flow (gallons per minute), and acid production (pounds per day) vs time over the sampling period. Because the coal was overlain with a porous sandstone, the mine drainage was consistent the year around even though the mine was

Jan 1, 1961

By E. Miller, J. M. Eldridge, K. L. Komarek

The thermodynamic properties of liquid Mg-Ge alloys have been determined between 1000°and 1500°K by an isopiestic method. Germanium specimens, heated in a temperature gradient and contained in covered graphite crucibles of special geometry, were equilibrated with magrtesium vapor in closed titanium tubes. The crucible design allowed free access of magnesium vapor to the samples during the equilibration to form alloys of magnesium and germanium, but prevented magnesium losses from the crucibles on quenching the titaniuin tubes to terminate the experimental runs, thus preserving the equilibrium alloy compositions. The activities and partial molar enthalpies of magnesium and the integral thermodynamic properties of the system were calculated from the experimental data. THE Mg-Ge phase diagram' shows one congruent melting compound, Mg2Ge, of essentially stoichio-metric composition, two eutectics, and very limited terminal solid solubilities. Very little information is available on the thermodynamic properties of the Mg-Ge system. The free energy of formation of Mg,Ge was recently deter-mined2 by a Knudsen cell technique in the temperature range 610° to 760°C. The standard enthalpy of formation of Mg,Ge was measured calorimetrically by Bever and coworkers.3 The present study was undertaken as part of a general investigation of the thermodynamic properties of the homologous series of Mg-Group IVB systems, i.e., Mg-Pb,4 Mg-Sn,5 Mg-Ge, and Mg-Si. An isopiestic technique was used which was developed by the authors5 for investigating the thermodynamic properties of liquid Mg-Sn alloys. Specimens of the nonvolatile component, contained in covered graphite crucibles, are heated in a temperature gradient in an evacuated and sealed titanium reaction tube, and equilibrated with magnesium vapor of known pressure. The method employs crucibles of special geometry which preserve the high-temperature equilibrium composition of liquid alloys having a highly volatile component such as magnesium on termination of the experimental runs by quenching the crucibles to room temperature. EXPERIMENTAL PROCEDURE First reduction germanium of 99.999+ pct purity (Eagle-Pitcher Co., Cincinnati, Ohio) and 99.99+ pct magnesium metal (Dominion Magnesium Ltd., Toronto, Canada) were used. The graphite crucibles were machined from high-density (1.92 g per cu cm) graphite rods (Basic Carbon Corp., Sanborn, N.Y.) which had a maximum ash content of less than 0.04 pct. The non-reactivity of graphite with germanium at the temperatures used in this study had been previously established by Scace and Sleck.6 The experimental procedure has been previously described in detail.5 The selection of a particular crucible geometry for a run was determined by a combination of imposed experimental conditions, the principle being that more tightly covered crucibles were required to preserve alloy compositions during quenching when higher magnesium pressures and higher specimen temperatures were used. Depending upon the composition range of the equilibrated alloys the source of the magnesium vapor was either pure magnesium or a two-phase mixture of Mg2Ge + Ge-rich liquid of known magnesium pressure. The experimental runs can be divided into the following three groups on the basis of crucible geometry and magnesium source material. Crucibles with Small Holes and Pure Magnesium Reservoirs. The crucible dimensions were identical to those of the Mg-Sn investigation5 except that the hole diameters were reduced to 0.010 in. because of the higher temperatures and higher magnesium pressures involved in the Mg-Ge system. During an equilibration run, magnesium vapor diffused from the reservoir to each specimen through the small holes, one drilled through the crucible lid and two others drilled through graphite baffles positioned vertically inside the crucible between the lid hole and the specimen. Since the magnesium pressure was high, i.e., in the range 117 to 277 Torr, during the equilibration time of approximately 24 hr, equilibration was not impeded by these holes. A specimen composition at equilibrium was fixed by the relative temperatures of the specimen and the reservoir, and by the thermodynamic properties of the system. Upon brine quenching the titanium reaction tube to end a run the vapor pressure of magnesium above the liquid alloys decreased exponentially with decreasing temperature, and the small cross-sectional areas of the holes (4.9 x 10"* sq cm) drastically reduced magnesium losses from the crucibles. Because of its low vapor pressure, germanium losses from crucibles during a run were at most 0.2 mg for pure germanium and correspondingly less for the alloys. This crucible geometry satisfactorily retained the equilibrium alloy compositions on quenching for magnesium-rich (from 3 to 33 at. pct Ge) alloys provided their temperatures were below the melting

Jan 1, 1967

By C. B. Alcock, L. I. Cheng

By the use of radiochemical methods for the study of the gas-liquid equilibria at low temperature, and for the determination of the sulfur contents of metal beads which had been equilibrated with H2S/H2 mixtures of known sulfur potential, it has been possible to obtain the liquid solubility and the free energy of solution of sulfur in liquid tin and lead at temperatures between 500°and 680°C. THE gas-liquid equilibrium method has proved in the past to be most successful in the determination of the thermodynamic behavior of dilute solutions of sulfur in liquid metals.1,2 One of the basic requirements for success with this method is that the volatility of both the metal and its lowest sulfide should be small, otherwise sulfide will be deposited at the cool end of the furnace, where it may react with the outgoing gases to form either sulfur-rich lowest sulfide or higher sulfides. The resultant value of the apparent equilibrium constant will then be lower than the correct one. This argument applies even at sulfur potentials below that in equilibrium with a separate condensed phase of the lowest sulfide at the reaction temperature, T. The mass of sulfide which is deposited at the cold end of the furnace, and hence the extent to which further reaction occurs with the outgoing gases, depends on the time taken for equilibrium to be reached between metal and gas. Since this will depend principally on the bulk of the metal phase which is used, one should clearly attempt to uie as small metal samples as possible. These considerations are important in the study of dilute solutions of sulfur dissolved in liquid tin and lead which both have moderately high vapor pressures as metals and form volatile sulfides. The limit on the size of the metal samples which may be used is set chiefly by the difficulties of analysis for very small amounts of sulfur. The oxygen or carbon dioxide combustion method, followed by iodimetric determination of the sulfur dioxide which is formed,has been found to be successful for the determination of small amounts of sulfur in copper, iron, cobalt and nickel.4 This method was unsatisfactory for sulfur dissolved in tin and lead, mainly because the sulfur dioxide was to some extent absorbed by the copious tin or lead oxide deposits which were formed on the walls of the combustion tube. Furthermore some of the sulfur was found to segregate on the surface of the beads as flaky sulfide crystals which would easily be lost in the transfer of a bead from a boat in the gas equilibration apparatus to one in the combustion apparatus. Oxidation in aqueous media to sulfate ion followed by precipitation as barium sulfate was, therefore, adopted as the analytical procedure. The gas-metal equilibrium experiments were all carried out with radioactive sulfur and thus the analysis involved the counting of barium radiosulfate. Furthermore the use of the radioisotope meant that the approach to the gas-metal equilibrium could be followed continuously by gas counting.' The metal beads were held separately in glass crucibles during equilibration and were transferred from the furnace to the beaker for dissolution in nitric acid still in the crucibles, and thus the possibility of sulfur loss by detachment of the sulfide segregates was eliminated. The temperature range of this investigation was 500° to 680°C. EXPERIMENTAL APPARATUS AND METHOD The apparatus consisted of two furnaces placed in series in a gas recirculation system, Fig. 1. One furnace F1, which was vertical was used to heat the alumina crucible, A, holding six metal beads in separate glass crucibles. The beads weighed between 300 and 700 mg each. The crucible assembly was introduced and removed from the furnace mechanically under a stream of oxygen-free argon. The other furnace, F2, was horizontal and was used to heat a cobalt Co9S8 mixture, held in an alumina boat, and made with radiosulfur containing about 1/2 millicurie per g of sulphur. This mixture, which was finely powdered, was used as a source of known H2S/H2 mixtures6 for a given furnace temperature. The recirculation system also contained a gas re-circulation pump (P), an end window Geiger-Miiller counter (N)—placed downstream of F1 so as to monitor the H2S pressure in the gas leaving this furnace— a sample volume for chemical analysis of the gas phase (G), gas drying tubes (D), filling taps and other standard ancillary equipment. The gas sampling volume was principally used in the cali-

Jan 1, 1962

By Boris J. Kochanowsky, Burke O. Trafton

Because of the strict requirements on the quality of limestone that are dictated by the users, the operator was compelled to find new approaches to produce a product of uniform and acceptable quality. The raw material is controlled and monitored every two minutes by a special computer in order to ensure its quality. The required minimum and maximum quality constraint had an adverse effect on performance and consequently cost. In order to improve this performance, a Monte Carlo simulation model was developed and tested for the optimal truck allocation. The input data is based upon the distribution of equipment performances and costs.

Jan 1, 1969

By R. D. Carnahan

The authors are to be complimented on their timely study of solution-hardening effects in a bcc metal. Unfortunately there are some misleading aspects of the paper that should be discussed and clarified which is the purpose of this letter. In particular the writer is concerned about the allusions to rate theory of deformation that are inferred by the authors. This position is taken on the basis first of the "weaker" temperature dependence of the yield and flow stresses of the alloy relative to pure niobium and second of the strong temperature dependence of the Young's modulus of elasticity. It is by now well-recognized that any collection of data points used to determine a flow-stress temperature-dependence relationship must be established under isostructural conditions, i.e., similar or identical sessile and mobile dislocation densities and arrangements. Admittedly this is a formidable experimental undertaking and not what would be expected in an exploratory investigation of the present kind. As an alternative to the former one can consider, however, the temperature dependence of flow stresses at comparable strains. In the present study the authors have elected to use the lower yield stress and ultimate strengths to exhibit the temperature dependence of their alloys except for the data points taken at liquid nitrogen temperature. Here they have used the proportional limit for the yield stress and the fracture stress for the ultimate strength. This seems to be an unrealistic choice particularly in view of the fact that this temperature is below the duc tile-brittle transition region for the alloy and no supporting data points were obtained between -55" and -196°C. If the authors' data in Fig. 2 are extrapolated and data points selected at a constant strain, for example a strain of 0.01, the reader can quickly verify that a temperature dependence exactly paralleling that of pure niobium is obtained.

Jan 1, 1967

By James F. Kemp

The Bulletin of the Institute for March, 1911, is chiefly devoted to papers upon the iron ores of northeastern Cuba. At that time information about the new developments in the peculiar brown hematites of the region was becoming widely circulated and interest was especially keen. For some years exploration had been conducted with pits and trenches and so great an area had been shown to contain ore in the Mayari, Moa, and Cubitas or San Felipe districts, that the reserves conveniently situated for the consumption of American furnaces were estimated as quite two billions of tons. In the subjoined footnote will be found a list of the principal papers of special interest which have already been published.' The further remark may, however, be made that the

Jan 1, 1915

By A. C. Fieldner

IN the Wall Street journal for March 1, 1941, was a tabulation of the construction under way or under negotiation by thirteen iron and steel companies for a predicted increase in annual coke production of 3,165,600 tons. That even this figure was short of the mark is indicated by other plans, then being considered, for a later expansion of 2,610,000 tons additional. Considerable progress has already been made on thin program, for approximately 500 new ovens were put in operation in 1941. and well over 200 should be completed in 1942. These figures include a number of units that replace older and obsolete equipment.

Jan 1, 1942

By G. C. Hancock

The operating plant of The Broken Hill Associated Smelters Pty. Ltd. is situated at Port Pirie in South Australia and it treats to finality the whole output of lead concentrates from the mines of The Zinc Corporation Ltd., North Broken Hill Ltd., and aroken Hill South Ltd. at Broken Hill, New South Wales. Lead bearing ores from other sources are also purchased for treatment and lead scrap and residues are treated on a toll charge basis. The present output of the plant is approximately 200000 tonnes of refined lead per annum and there is a substantial production of by-products including refined silver, gold, cadmium, antimonial lead alloys, copper matte and sulphuric acid. Recently the Company commenced the production of zinc by slag fuming and electrolysis from a six million ton dump of lead blast furnace slag, which has been accumulating at Port Pirie for over fifty years. The slag fuming plant contains two furnaces of conventional design, but features a high degree of pre-heat for the blast air and this is obtained by the use of all-metal recuperators. The raw zinc oxide fume produced by the plant is roasted in a rotary kiln prior to treatment in the leaching and electrolysis sections, which follow conventional practice for nigh current density plants. Present output is approximately 36000 tonnes of electrolytic zinc per annum.

Jan 1, 1970

By Gilbert Soler

Producers of alloy steels recognize the importance of chemical composition in relation to the hot-working properties and the typical surface defects found in their product. Each analysis of steel has its own peculiar characteristics. Under conditions of standard mill practice each analysis is susceptible to certain types of defects. Mill practice must be varied to obtain the best combination of surface and internal quality in the product. Chemical composition influences the cast structure and crystallization characteristics of the ingot. It also determines the rate of heating and cooling, the plastic hot-working range, and the phase structure of the steel at various temperatures. as well as the tendency toward scale formation and decarburization. This paper endeavors to emphasize the manner in which chemical composition affects the various properties of steel, and to indicate the relative importance of these factors in relation to the hot-working properties and surface characteristics of killed steel. The influence of chemical composition may be outlined as follows: I. Effect on the cast structure of steel, including: A. State of deoxidation, and type of inclusions. B. Gas content of steel. C. Freezing point and melting point of steel. D. Crystallization characteristics and segregation. 11. Effect on the hot-working properties and surface characteristics of steel, including: A. Plastic hot-working range. B. Phase structures at hot-working temperatures. C. Rate of heating. D. Cooling characteristics. E. Scale formation. F. Surface decarburization. EFferect of Chemical Composition on Cast Structure of Steel State of Deoxidation and Type of Inclu-sions.—The state of deoxidation is limited by the final chemical analysis desired in the finished product, and is controlled primarily by carbon, manganese, silicon, and aluminum, and to a lesser degree by chromium, titanium, vanadium, or other deoxidizing elements. The degree of deoxidation affects the density of the cast structure and broadly classifies the steel as killed, semikilled, or rimming. This in turn manifests itself in surface characteristics. The manner and extent of deoxidation also controls the amount, type, and distribution of nonmetallic inclusions formed. The equilibrium of manganese, silicon and aluminum with the slags and pouring refractories with which the metal comes in contact is important, especially in regard to inclusions of fire-clay origin. Some surface Seams and hot-working difficulties can be traced to nonmetallic inclusions.

Jan 1, 1941

By Gilbert Soler

Producers of alloy steels recognize the importance of chemical composition in relation to the hot-working properties and the typical surface defects found in their product. Each analysis of steel has its own peculiar characteristics. Under conditions of standard mill practice each analysis is susceptible to certain types of defects. Mill practice must be varied to obtain the best combination of surface and internal quality in the product. Chemical composition influences the cast structure and crystallization characteristics of the ingot. It also determines the rate of heating and cooling, the plastic hot-working range, and the phase structure of the steel at various temperatures. as well as the tendency toward scale formation and decarburization. This paper endeavors to emphasize the manner in which chemical composition affects the various properties of steel, and to indicate the relative importance of these factors in relation to the hot-working properties and surface characteristics of killed steel. The influence of chemical composition may be outlined as follows: I. Effect on the cast structure of steel, including: A. State of deoxidation, and type of inclusions. B. Gas content of steel. C. Freezing point and melting point of steel. D. Crystallization characteristics and segregation. 11. Effect on the hot-working properties and surface characteristics of steel, including: A. Plastic hot-working range. B. Phase structures at hot-working temperatures. C. Rate of heating. D. Cooling characteristics. E. Scale formation. F. Surface decarburization. EFferect of Chemical Composition on Cast Structure of Steel State of Deoxidation and Type of Inclu-sions.—The state of deoxidation is limited by the final chemical analysis desired in the finished product, and is controlled primarily by carbon, manganese, silicon, and aluminum, and to a lesser degree by chromium, titanium, vanadium, or other deoxidizing elements. The degree of deoxidation affects the density of the cast structure and broadly classifies the steel as killed, semikilled, or rimming. This in turn manifests itself in surface characteristics. The manner and extent of deoxidation also controls the amount, type, and distribution of nonmetallic inclusions formed. The equilibrium of manganese, silicon and aluminum with the slags and pouring refractories with which the metal comes in contact is important, especially in regard to inclusions of fire-clay origin. Some surface Seams and hot-working difficulties can be traced to nonmetallic inclusions.

Jan 1, 1941

By Benjamin Tillson

To MOST mine operators, it seems evident that there is a drill-steel problem, although under certain conditions the amount f drill-steel breakage does not appear serious. What is at fault? It may be one or a combination of circumstances. The development of rock drills to the hammer-drill type in place of the old reciprocating piston drill, probably is one important cause for the greater steel breakage. Perhaps the manufacturers of drill steel have failed to realize what alloys are needed for this new service or have overlooked the changes in the art of rock drilling. Although suitable alloys are provided, they may not be so handled in the manufacturing process as to be in the best condition to withstand the demands of rock drilling. The mine operator may be at fault in desiring to use the smallest possible drill-steel section in order that the gage of the drill bits may be correspondingly small and the amount of footage drilled per unit of labor may be greater; or the black-smithshop practice at the mines may need improvement. The miner who uses the drill steel may also require more intensive supervision and education. Again, the manufacturer of rock drills may have failed to study the types of blows the steel alloys will withstand satisfactorily and which their tools are delivering and so he may not know whether or not a different design of rock drill would equal or excel their present drilling speeds without treating the drill steel so severely. All of these hypotheses probably have their supporters. On the other hand, perhaps we are seeking too much service from drill steel and we need a fuller realization of the fatigue strains developed and should prepare to relieve these by a periodic heat treatment of the steels. However, we do not find any proof that any of these suppositions may be held responsible for the drill-steel breakage attendant to mining. The proposed investigation of this matter by the U. S. Bureau f Mines is fully warranted in the promotion of the conservation of labor and material, and the safety of the workmen. The great range of field conditions, as well as the scope of the research, requires the energetic cooperative support of many interests. Various manufacturers of steel,

Jan 5, 1921

By H. OSBORG

THE patent literature of alloys for the last two decades or so indicates that the number of liatents referring to smaller and smaller percentages of essential alloying constituents is on the increase, whereas the number of patents relating to considerable percentages of alloying additions becomes smaller. The claims regarding physical properties indicate consistently higher and more rigid values and show the possibility of modifying the physical properties by only slight changes in the percentage of minor constituents or by applying different methods - of treatment. Alloys of the same base have been made suitable for a number of different applications by intelligently and rigid- ly controlling their composition, melting, casting, working, and heat-treatments. Other trends indicated in the development of modern alloys are higher corrosion resistance, higher fatigue limits, and "stability" in volume.

Jan 1, 1937

By J. E. Jopling, J. R. Chenneour, E. L. Derby, S. R. Elliott

The Marquette range, on which are situated the iron mines of Mar-quette County, together with a few in Baraga County, Mich., extends from a point 10 miles southwest of Marquette westward for 30 miles. The tracts are usually a multiple of the standard 40-acre parcel, which is the smallest government subdivision of a square mile or section. About half of the mines are held in fee, these being owned by the older mining companies. Some of them date back to about 1880, and a few are as early as 1850. During the past 40 years most of the mines opened have been on leased lands, the royalty being either for a stated amount per ton or a percentage of the selling price of the ore at the lower lake ports, or the selling price on board of cars at the mine. The first merchantable body of ore discovered in the Lake Superior district was found, in 1845, at what is known as the Jackson mine, near Negaunee. This ore was hard hematite. After unprofitable attempts had been made, in 1848, to smelt it in forges, shipments were begun to lower lake ports, which increased rapidly upon the completion of the locks at Sault Ste. Marie, in 1855, and the railroad from the mines to Marquette, in 1857. Beginning with the Pioneer, in 1858, a number of small charcoal furnaces were built to smelt a part of the product. At various points in the upper and lower peninsulas, large charcoal furnaces are still making iron from the ores of the Marquette range. In connection with these furnaces are byproduct plants. As the deposits were opened up, soft ore was encountered, but for a few years this was disregaided, as only the hard ore was used. Underground mining was begun about 1880 and during the next few years the open-pit mines producing high-grade ore were exhausted. The first mines in the district were owned by the Jackson, Cleveland, Lake Superior, Lake Angeline, Champion, Iron Cliffs, Humboldt, Republic, and Michigamme companies. Many of these companies have been merged in the holdings of The Cleveland-Cliffs Iron Co., which controls most of the tonnage of the district.

Jan 1, 1925

By R. F. Mehl, W. Batz, C. Wells

Diffusion coefficient values for carbon in austenite covering a wide range of temperature and composition have been determined employing statistical methods. In addition, the relation between concentration and each of the following, D (diffusion coefficient), Q (activation heat of diffusion), and A (the constant in the diffusion equation), has been obtained. A study of the rates of diffusion of austenite was published in Metals Technology in 1940.' The present investigation is an extension of the earlier work, undertaken (1) to obtain values of the coefficient of diffusion, D, over a much wider range of carbon concentration, and (2) to provide data in all ranges of concentration and temperature in such abundance that statistical methods could be employed to evaluate the accuracy of the data with unusual precision. Composition of Materials: Composition of materials used in this research program are listed in table I. These materials, all forged to about 1 1/4 in. rounds, consist of a high-purity iron, Armco iron, a large number of laboratory-made plain carbon steels containing amounts of impurities normally expected in high-quality commercial steels, and three silicon steels. Since it was known at the time these steels were being made that impurities in the amounts present were unlikely to affect carbon diffusion rates' significantly, the effort made to obtain high-purity steels was not as persistent as it otherwise would have been. Procedure: In general, the procedure followed by Wells and Mehl and described' in detail in an earlier publication' is the one used by the present authors. However, certain modifications have been made which it is believed allow diffusion data to be interpreted more objectively and correctly. These are described completely under appropriate subheadings which follow. Experimental Procedure: Experimental procedure includes (1) the preparation of specimens by welding steels of different carbon contents, (2) the heating of these for certain times at selected temperatures in order to diffuse carbon along the specimens across the welded "interface," and (3) the determination of the carbon distribution across the diffusion zone. Preparation of Specimens: Prior to welding steel of one carbon content to iron or steel of another carbon content, surfaces to be welded are machined perpendicular to the longitudinal axis of cylinders which are about 3/4 in. in diam and 1 1/2 in. long. The prepared, flat, parallel surfaces are brought together and butt-welded electrically. Evidence of a good weld is given in fig. 1. Welding temperature

Jan 1, 1951

By P. Chiotti, J. T. Mason

Ther?nal, X-ray, metallographic, and vapor pressure data were obtained to establish the phase diagram and standard free energy, enthalpy, and entropy of formation for the compounds in the Sw-Zn system. Four compounds, SmZn, SmZn2 , SmZn4.s, and SmZn8.5, melt congruently at 960°, 94Z°, 908°, and 940°C, respectively. The cornpounds SlnZns, Sm3Znll, and SnzZn7.3 undergo peritectic decomposition at 855", 870°, and 890C, respectively. Another compound of uncertain stoichiometry, SmZn11, undergoes peritectic decomposition at 760°C. Four entectics were observed with the following compositions in weight percent zinc and eutectic tenzperatures in degrees Centigrade: 12 pct, 680°C; 36 pct, 890°C; 58 pct, 850°C; and 72 pct, 900°C. An allotropic transformation and a composition range were observed for the SmZnz compound. The transfor)nation varies from 905" to 865°C as the zinc content increases from 16.0 to 48.5 wt pct, respectively. The free energy of formation of the compounds at 50PC varies between -15.9 kcal per mole for SmZn to -51.1 kcal per mole for SmZn,.,. Corresponding enthalpies vary between -19.2 to -78.3 kcal per mole. The ther-modynamic properties for the liquid alloys are described by the relations: A search of the literature revealed very little information on the Sm-Zn system. Chao et al.&apos; as well as Iandelli and palenzonai have reported the structure of SmZn to be cubic B2 type and Kuz&apos;ma et al3. have reported the structure of -sm2zn17 to be of the Th2Ni17 type. The purpose of this work was to establish the phase diagram of this system, to determine the zinc vapor pressure over the solid two-phase regions of the SYstem, and to calculate the thermodynamic properties of the compounds. MATERIALS AND EXPERIMENTAL PROCEDURES The metals used in this investigation were Bunker Hill slab zinc 99.99 wt pct pure and Ames Laboratory samarium. Analysis of the samarium by chemical, spectrographic, and vacuum-fusion methods gave the following average impurities in ppm: Nd, <200; Eu, <100; Gd, <100; Y, <50;Ca, 225; Ta, 400; Mg, 10; Cu, ~50; 0, 175; H, 20; and N, 15. The elements Fe, Si, Cr, Ni, Al, and W were not detected. The samarium was received as sponge metal and was kept under argon except when being cut with shears and when being weighed. Tantalum was found to be a suitable container for alloys with zinc contents up to the Sm2Znl, stoichio-metry. At higher zinc contents the grain boundaries of the tantalum containers were penetrated by the alloy and the containers failed during prolonged annealing. About 25 g of massive zinc and samarium sponge were sealed in tantalum crucibles equipped with thermocouple wells. These crucibles were in turn sealed in stainless-steel jackets. All closures were made by arc welding under an argon atmosphere. The samples were equilibrated in an oscillating furnace and in some cases were given various heat treatments in a soaking furnace. After appropriate heat treatment the steel jackets were removed and the alloy subjected to differential thermal analysis. The apparatus was calibrated against pure zinc and pure copper and found to reproduce the accepted melting points within 1°C. Alloys were subsequently subjected to metallographic examination and those of appropriate compositions were used for X-ray diffraction analysis and for zinc vapor pressure determinations. The vapor pressures were determined by the dewpoint method. Both the differential analysis and dewpoint measuring apparatuses have been described in earlier papers.4, 5 All alloy samples were etched with Nital (0.5 to 3 pct nitric acid in alcohol) except the samarium-rich alloys. These more reactive alloys were electro-polished in a 1 to 6 pct HClO4 in methanol solution at -700c at a potential of 50 v. EXPERIMENTAL RESULTS Phase Diagram. The results of thermal analysis are indicated by the points on the phase diagram, Fig. 1. Eight compounds and four eutectics were observed. The composition of the compounds and their melting or peritectic temperatures are given on the phase diagram. The four eutectic compositions in wt pct zinc and eutectic temperatures in % are: 12 pct,- 680°C; 36 pct, 890°C; 58 pct, 850°C; and 72 pct, 900°C. The stoichiometry of the most zinc-rich compound is still uncertain, but is very likely either SmZnll or SmZnlz. However, to simplify the presentation which follows it will be referred to as SmZnll. As shown on the phase diagram the phase regions for some of the samarium-rich alloys have not been unambiguously established. A sample of pure samarium was observed to transform at 924°C and to melt at 1074"C, in good agreement with corresponding val-

Jan 1, 1968

By A. G. Spillette, R. L. Nielsen

The purpose of this paper is to further the understanding of reservoir response to hot-water injection by desuribing a two-dimensional, mathematical model of the process. Key assumptions are that no gas phase is present, and that the injected fluid reaches thermal equilibrium instantaneously with the reservoir fluids and sand. The resulting system of three partial differential equations is solved simultaneously through the use of a "leap-frog" application of standard alternating direction implicit methods for the solution of the mass-balance equations and the method of characteristics for solution of the energy-balance equation. The utility of the mathematical model is demonstrated by comparing numerical and analytic temperature distributions for hot-water bank injection and by comparing calculated with observed field behavior. Additional calculations show that hot waterfioding can recover significantly more oil than cold waterflooding, and that a hot-water bank recovers, with less energy input, nearly as much oil us continuous injection. Introduction Consistent field success with hot fluid injection processes requires good reservoir description and a thorough understanding of recovery mechanisms. The latter is fostered by a combination of well designed experimental studies and physically sound mathematical modeling. The purpose of this paper is to further the understanding of reservoir response to hot-water injection by describing a two-dimensional mathematical technique, indicating its validity, and demonstrating its utility for studying the effects of reservoir and operating parameters. Published experimental studies of hot fluid injection processes are few." Even if extensive data were available, two considerations discourage exclusive reliance on laboratory or field work. First, because of the severity of scaling requirements," laboratory results must be interpreted with care. Second, because of the one-shot nature of field experiments — injectivity/productivity tests and pilot floods—results seldom are available over the desired range of operating conditions. These factors emphasize the need for devoting attention to mathematical modeling to complement laboratory and field work. Through the use of mathematical models, scaling uncertainties can be bridged and response can be predicted for unique combinations of reservoir and operating conditions. Numerous mathematical models developed during recent years enable us to calculate temperature distributions, thermal efficiency (or conversely, fraction of heat lost), and oil recovery behavior for hot fluid injection. Ramey" and Spillette&apos; recently have provided reviews of these methods. Most models have concentrated on predicting temperature distributions and thermal efficiency; few have been directed at predicting oil recovery.&apos;."1° Although these techniques are useful for estimating effects of reservoir parameters and operating conditions on process performance, results are limited by the assumptions made and by the methods of coupling independently solved fluid-flow and energy-balance equations. A computer-based method is presented for predicting total reservoir response to hot-water injection that obviates most simplifying assumptions. The model simulates fluid flow and heat transfer in two dimensions within a vertical cross-section spanning the oil sand and adjacent unproductive strata. Known numerical procedures are used to solve the governing partial differential equations. The mathematical model handles the effects of reservoir heterogeneity, gravity, capillarity, relative permeability and temperature-dependent fluid properties. In addition, a wide range of operating conditions can be modeled, including hot-water followed by cold-water injection. Mathematical Description of Hot-Water Injection Key assumptions in the mathematical model for hot-water injection are that (1) no gas phase is present and (2) the injected fluid reaches thermal equilibrium instantaneously with the reservoir fluids and sand. Relative permeability and capillary pressure are assumed independent of temperature. Darcy&apos;s law for multiphase fluid flow relates the velocities of the oil and water phases to the phase pressure gradients by the following relations:

Jan 1, 1969

By E. W. Pehrson, J. W. Furness

THE five charts presented here- with are part of an original group prepared by the U. S. Bureau of Mines showing the international trade in the principal metals and metallic ores. Charts 011 anti- mony, chromite, copper, lead, manganese, mercury, nickel, tin, tungsten, and zinc were published in the February, 1936, issue of the Engineering and Mining Journal. Those shown here include bauxite, aluminum, iron ore, pig iron, and the platinum-group metals.

Jan 1, 1936