Search Documents

By R. E. Robbins, H. R. Brager

THIS note describes an unusual result obtained in an electron microscope investigation of cavities produced in commercial type 304 stainless steel irradiated in a thermal reactor (ETR) at 290°C to a high neutron flu-ence, 6 x loz1 n per sq cm. The analysis of the steel used is given in Table I. The unusual result is that the calculated quantity of helium gas produced by transmutation during the irradiation, 12 ppm, is less than one-tenth the amount of gas necessary to balance the surface tension of the observed cavities produced in the steel during ETR irradiation. Therefore, the cavities would be expected to behave like voids; however, they behave like "gas filled" bubbles. The maximum quantity of helium produced in the steel by B" transmutation was 8 ppm. In addition, the amount of helium formed by (n, (1) fast neutron reactions with the major alloy constituents and nitrogen was calculated to be 4 ppm based on the tabulated differential or effective fission-averaged cross sections of elements in type 304 stainless steel irradiated in typical thermal reactors.', In previous investigations concerning commercial austenitic stainless steel irradiated in a thermal reactor, the amount of helium gas calculated to be produced by transmutation has always been significantly greater than the amount calculated on the basis that the bubbles were gas filled, PPs= 2y/R. The balance of the gas was assumed to be in bubbles smaller than could be detected on the electron micrographs. Accordingly, the bubbles were attributed to helium produced from transmutation of impurity boron by thermal neutrons. These bubbles were not uniformly dispersed in the matrix but were located principally at grain boundaries, or were radially positioned around a few precipitates located in the matrix and at the grain bundaries., 4 Voids have also been observed in austenitic stainless steel irradiated at high temperature to high neutron fluences in the EBR-I1 and Dounreay Fast Reactors. The voids were uniformly distributed throughout the matrix. The amounts of helium gas produced by transmutation during these irradiations were less than one-tenth the amounts needed to balance the surface tension of the voids formed by the fast reactor irradiation. The fast reactor results are quite analogous to those reported here for the ETR irradiated steel. Electron microscope examination of the fast reactor irradiated material after a 1 hr postirradiation annealing at 900°C disclosed that essentially all the voids had been eliminated. The authors stated that the voids had developed due to the high concentration of vacancies produced during irradiatin., 6, ' The microstructure of the ETR irradiated material as-tested at 75O°C, Fig. 1, contained about 2 X lot5 cavities per cm3 with an average diameter of 110A. With the Van der Waals b correction and y = 1500 ergs per cm2, 300 ppm He would balance the surface tension of the observed cavities. Stereoscopic examination of the electron micrographs showed that the cavities were neither preferentially located near the grain boundaries nor highly concentrated at specific regions or precipitates. The cavities were nearly uniformly distributed throughout the matrix, on dislocations and at grain boundaries. These observations imply that the cavities were not the sole results of B'O

Jan 1, 1969

By J. R. McWilliams

Several of the current concepts of brittle fracture involve consideration of the existence of defects or flaws. Griffith 1 observed that the tensile strength of brittle materials was several orders of magnitude less than might be expected from the calculated strength of the molecular bonds. He was able to show that the stress concentration at the tip of an elliptical crack is sufficient to raise the local stress level many fold. He therefore proposed that real materials do contain such stress risers in the form of minute cracks and that this accounts for the rather large difference between theoretical and actual strengths of brittle materials. The degree of stress magnification depends to a great extent upon the orientation of the crack with respect to the general stress system, and to the general geometry of the crack.

Jan 1, 1967

By Nathaniel Arbiter, Norman L. Weiss

Factors now accelerating the trend to larger concentrators and larger equipment units are reviewed. After almost 40 years of stability with unit sizes less than 100 cu ft, 200 and 300-cu-ft flotation-cell units are now operating and a 500-cu-ft machine is being built. The design of these cells is considered, as is the design and operation of flotation circuits against the background of the need to achieve greater process efficiency while holding down operating and investment costs. Particular attention is paid to the scale-up problem. With the newer cells having five to ten times higher unit capacities, the advantages resulting from this in sampling, mill operation nnd control, testing and plant layout are indicated, as well as the broad direction for changes in the overall design of 50,000 to 100,000-tpd concentrators. A comparison is given of the available larger cells of U.S. manufacture with analysis of differences and similarities. After almost 60 years of application in this country, froth flotation is still by far the most important process for concentrating metallic ores as well as a number of nonmetallic ores including fluorspar, phosphate rock, and potash. Its use on iron ores and coal is increasing. In the metals groups, the largest plants and the greatest progress are found in copper and molybdenum mills, and the section of this paper that deals with applications will be found most pertinent to that field. During its long reign, the flotation process has passed through several phases of evolution and has achieved progress in economy, efficiency. and simplicity of operation. Much of today's success in the flotation of low-grade ores can be attributed to that progress. Even more important to us than our ability to cope with today's conditions are tomorrow's problems, which we can contemplate with some prescience and confidence. Our annual production of copper, lead, zinc, and molybdenum—to mention only the most important metals occurring in the U.S. as sulfides- must be held at a high level in the face of a declining grade of ore. It is probable that the tonnage of such ores mined and processed will double in this country before the turn of the century. Not only will many of the existing flotation mills be enlarged again and again, but larger mills will be built here and abroad to meet our needs. At this moment, in fact, there are at least three proposed new foreign mills or expansions that envision 100,000-tpd milling rate on copper ores. Table 1' shows the trend in copper ore grades in U.S. in recent years. Table 2' shows the projected annual growth rate of consumption 1966-1985. A study by one of the authors 25 years ago showed that of 32 copper mills in North America with more than 100-tpd capacity, only eight had capacities exceeding 10,000 tpd. The average for these eight was 25,000 tpd. These included the three giants of that day, Magna, Arthur, and Morenci; the other five averaged a little over 10,000 tpd. Today instead of the eight mills with capacities exceeding 10,000-tpd capacity we have 25, and the mill with less than 1000-tpd capacity is fast becoming extinct. Much less range is found in lead and zinc mills, which are still generally small except for the few with over 1000-tpd capacity in Missouri, Utah, and Idaho, and a few zinc ore mills in the same size category. Molybdenum and potash operations are the fastest growers in North America today, but when one considers the projected increase in consumption of copper together with the projected decrease in grade of ore (3% annually), he can foresee that copper ore milling will soon lead the list. Technological improvements to meet the challenge of lower-grade ores have taken the wholly predictable path toward bigger equipment. In mining, shovels, draglines, scrapers, and trucks have led the way; in ore processing, we have seen a rapid increase in size of grinding mills, flotation cells, and pumps. Twenty-five years ago, for example, the 10-ft-diam ball mills treating 2000 tpd at Morenci were considered the giants, but today some grinding mills in similar service have five times that capacity. The specific matters to be dealt with in this paper are 1) the underlying principles that affect flotation-machine design, and the conditions required to produce

Jan 1, 1971

By G. E. Perry, J. F. Bruskotter, D. G. Russell, J. H. Goodrich

The depletion performance of gas wells has been investigated by mathematical simulation techniques. The gas well model which was studied consisted of a single well located in the center of a bounded, cylindrical, homogeneous reservoir. Dependency of gas compressibility and viscosity on pressure was considered in studies of well performance at both constant mass flow rate and constant flowing pressure conditions. To carry out the investigation, the nonlinear, second-order, partial differential equation which describes Darcy flow of a nonideal gas through porous media was solved numerically. Some of the previous investigations of gas well performance have been of limited general use, because assumptions were introduced to simplify either the gas properties or the basic differential equation. Other studies have been rigorous in these respects but have presented a very limited set of calculated results. The present study was attempted to present a rigorous theoretical model and sufficient numerical results to permit meaningful conclusions to be drawn. It was found that all terms must be retained in the partial differential equation to make accurate predictions. The neglect of higher-order terms, e.g., terms of the order of the "gradient squared", leads to serious material balance errors at large times and to conservative estimates of gas well performance. The higher the gas flow rate and/or the lower the permeability-thickness product of the formation, the more pronounced are these deviations. For example, in a well draining 640 acres in a 25-md-ft formation (8,120 MMcf gas in place) at a constant rate of 993 Mcf/D, the rigorous solution predicts a bottom-hole pressure decline from 4,000 to 1,000 psia in 8.7 years. If higher-order terms are neglected in the differential equation, this decline in pressure is predicted to occur in 5.3 years. With the results of the numerical solution of the differential equation as a basis, simple, easy-to-use approximations for predicting gas well performance for Darcy flow conditions have been developed. These simple approximations are based on the familiar equations for flow of a single, slightly compressible fluid. The approximate methods possess a high degree of accuracy and enable the prediction of long-term gas well performance to be made quickly and accurately without the use of a digital computer. Both transient and stable flow period approximations were developed. INTRODUCTION In recent years income from the sale of natural gas and associated products has represented an ever-incre as ing fraction of the industry's total revenue from operations. To meet the surge in demand for natural gas, the industry has depended heavily upon established reserves and has actively pursued development of new reserves. The search has progressively led to reservoirs which yesterday were too tight and/or deep to yield the desired return on invested capital. More than ever before, evaluation accuracy is now required to forecast the criteria upon which engineering recommendations and management decisions are based. Considerable effort has been expended by both research and operations personnel on the development and application of methods for analyzing and predicting the performance of gas wells. Fundamentally, the problem is the familiar one of extracting data during the drilling, testing and early production life of a well and applying these data within an accurate simulation model to predict long-term behavior. During the past 30 or more years a voluminous literature dealing specifically with gas field problems has been generated. A recent book' lists a comprehensive bibliography of published material through 1959. Over 1,200 references are cited. Since then 39 additional articles on natural gas technology have been published in Transactions volumes of the Society of Petroleum Engineers of AIME. Most existing theory for predicting gas well performance requires that one or more idealizations (e.g., steady-state flow, ideal gas of constant viscosity, small and constant compressibility and constant-viscosity fluid) be applied. Although existing theory may apply directly or be adapted by various artifices to describe specific gas well and reservoir behavior, no widely applicable method is available, and existing methods appear to be subject to appreciable error unless better limits of applicability are defined. The objectives of this paper are (1) to present numerical solutions to the partial differential equation describing gas flow under conditions of general interest in gas well performance prediction work, (2) to present solutions which possess a high order of accuracy for both transient and stabilized flow periods of a well producing at constant rate or constant pressure, and (3) to develop and present simplified relationships which can be used as high-order approximations to the exact numerical results for fast and accurate predictions of gas well performance at the operating level. Combined, these objectives are designed gen-

Jan 1, 1967

By Frank C. Greene

The results of drilling in Missouri in 1938 are overshadowed by the leasing activity in northern Missouri, which began about the middle of the year. Nothing like it has ever been witnessed by the oil industry. With no production except a minor amount of gas, and with no drilling except in Clay, Platte and Marion Counties, a leasing campaign has embraced most of the counties north of the Missouri River and spread into southern Iowa, southeastern Nebraska and northeastern Kansas. It is reported that nearly all farms that could be leased without payment of a bonus have been leased, mostly on 10-yr. contracts, and at the end of the year a policy of bonus paying is in effect. Many of the major oil companies are leasing in the area and at least 15 of them are represented by scouts. Similarity to the Illinois Basin, low-priced leases and low drilling costs are among the reasons advanced for the leasing activity. Drilling activity in Missouri increased nearly two-thirds over 1937, with a total of 164 completions. The main activity was the extension of the "shoestring" of the so-called Bartlesville gas pool in Jackson County. It now seems that this sand is probably at the horizon of the Burbank sand. A new Squirrel sand oil pool was discovered in Jackson County. Cass County had five oil wells, with 63 bbl. initial production, four gas wells with 542,000 cu. ft. initial open flow, and 15 dry holes. Jackson County had three oil wells, with 24 bbl. initial production, 56 gas wells with 52,021,168 cu. ft. initial open flow and 57 dry holes. In Vernon County seven oil wells, with about 36 bbl. initial production, and two dry holes were completed. The oil production dropped off very quickly. In counties where wildcatting was carried on, new production was found. Clay County had seven dry holes, Hickory and Marion one each; Platte, four and St. Clair, two.

Jan 1, 1939

By B. E. Thompson, H. B. Fuqua

For a very brief description of the North Texas area, and the general geological features with which it is associated, the reader is referred to the opening paragraph of last year's summary1. A more complete discussion of the structure of the area, together with other interesting data concerning it, has been published recently by the Bureau of Economic Geology at the University of Texas2. It has been impossible for the authors to isolate the statistics for production for each of the many small pools of this district, as such statistics are not kept by operators except by counties or arbitrary divisions of counties. The total number of wells drilled in Archer, Wichita and Clay counties also has been subject to some estimate, as many of the shallower holes are not reported. While both routine development in proven or semiproven areas and exploratory drilling during 1935 showed an increase over the year 1934, the discovery of new producing areas of importance did not show improvement over that period. Several extremely local productive spots within semiproven areas were found in Archer, Cooke and Wilbarger counties; and extensions to older producing areas were developed in Archer, Baylor, Cooke, Montague, Wichita and Wilbarger counties. In Archer County, the Grace and Woods No. 1 Archer County (Fee), 4 miles northwest of Archer City, in the Thomas Glass survey, encountered a sand from 2836 to 2845 ft. of Pennsylvanian (lower Canyon) age, which showed an initial yield of 75 bbl. daily. While its production is of negligible importance, it is given special mention in this review because of the fact that it is producing from a new and deeper horizon than has been previously exploited in the county. Little deep development occurred in the district during the year. The Walter Gant No. 2 C. M. Worsham in J. M. Swisher survey, about 14 miles east of Henrietta, in Clay County, was abandoned at 5127 ft. in

Jan 1, 1936

By Frank C. Greene

The results of drilling in Missouri in 1938 are overshadowed by the leasing activity in northern Missouri, which began about the middle of the year. Nothing like it has ever been witnessed by the oil industry. With no production except a minor amount of gas, and with no drilling except in Clay, Platte and Marion Counties, a leasing campaign has embraced most of the counties north of the Missouri River and spread into southern Iowa, southeastern Nebraska and northeastern Kansas. It is reported that nearly all farms that could be leased without payment of a bonus have been leased, mostly on 10-yr. contracts, and at the end of the year a policy of bonus paying is in effect. Many of the major oil companies are leasing in the area and at least 15 of them are represented by scouts. Similarity to the Illinois Basin, low-priced leases and low drilling costs are among the reasons advanced for the leasing activity. Drilling activity in Missouri increased nearly two-thirds over 1937, with a total of 164 completions. The main activity was the extension of the "shoestring" of the so-called Bartlesville gas pool in Jackson County. It now seems that this sand is probably at the horizon of the Burbank sand. A new Squirrel sand oil pool was discovered in Jackson County. Cass County had five oil wells, with 63 bbl. initial production, four gas wells with 542,000 cu. ft. initial open flow, and 15 dry holes. Jackson County had three oil wells, with 24 bbl. initial production, 56 gas wells with 52,021,168 cu. ft. initial open flow and 57 dry holes. In Vernon County seven oil wells, with about 36 bbl. initial production, and two dry holes were completed. The oil production dropped off very quickly. In counties where wildcatting was carried on, new production was found. Clay County had seven dry holes, Hickory and Marion one each; Platte, four and St. Clair, two.

Jan 1, 1939

By H. B. Fuqua, B. E. Thompson

For a very brief description of the North Texas area, and the general geological features with which it is associated, the reader is referred to the opening paragraph of last year's summary1. A more complete discussion of the structure of the area, together with other interesting data concerning it, has been published recently by the Bureau of Economic Geology at the University of Texas2. It has been impossible for the authors to isolate the statistics for production for each of the many small pools of this district, as such statistics are not kept by operators except by counties or arbitrary divisions of counties. The total number of wells drilled in Archer, Wichita and Clay counties also has been subject to some estimate, as many of the shallower holes are not reported. While both routine development in proven or semiproven areas and exploratory drilling during 1935 showed an increase over the year 1934, the discovery of new producing areas of importance did not show improvement over that period. Several extremely local productive spots within semiproven areas were found in Archer, Cooke and Wilbarger counties; and extensions to older producing areas were developed in Archer, Baylor, Cooke, Montague, Wichita and Wilbarger counties. In Archer County, the Grace and Woods No. 1 Archer County (Fee), 4 miles northwest of Archer City, in the Thomas Glass survey, encountered a sand from 2836 to 2845 ft. of Pennsylvanian (lower Canyon) age, which showed an initial yield of 75 bbl. daily. While its production is of negligible importance, it is given special mention in this review because of the fact that it is producing from a new and deeper horizon than has been previously exploited in the county. Little deep development occurred in the district during the year. The Walter Gant No. 2 C. M. Worsham in J. M. Swisher survey, about 14 miles east of Henrietta, in Clay County, was abandoned at 5127 ft. in

Jan 1, 1936

[Abrahamson, Guy C., (5'43) 1st Lt., A.C., 0-880861, Base Weather Sta., Fairfeld-Suisun AAB, Suisun, Calif. Adam, Howard Wilbur, (S'46) 45 Eaton Ave., Woburn, Mass. Aguilar, Ruperto G., (S'43) Texas College of Mines, El Paso, Texas. Ainge, Ronald Farra, (S'43) Otago University, Dunedin, New Zealand. Albala, Américo, (S'44) Casilla 4106, Santiago, Chile. Albrecht, Theodore J„ (S'42) Pfc., Co. F, Syme Hall, Rm. 1, SCU 3421, ASTP, N. C. State College, Raleigh, N. C. Aldridge, E. E., Jr., (S'39) Box 58, Eagle Pass, Texas. Alfred, Robert M., (S'40) 25 South St., Brighton, Mass. Allan, Douglas H. W., (S'40) 460 Main St., E., Hamilton. Ont.. Canada.]

Jan 1, 1946

By Josef Intrater

A dilatometric determination of the a + ß region temperature limits was performed on vacuum melted Zircaloy-2. The temperature of transformation for a-a+ß and a+ß — ß on heating and cooling as a function of rate of heating and heat treating history was studied. The limits were found to be 815° to 830°C to 975° to 995°C on heating and from 960° to 930°C to 785° to 770°C on cooling. A 5° to 15°C increase was observed for a- a + ß with increased rate of heating and a 20° to 30°C decrease for ß - a + ß with increased rate of cooling. 1 HE transformation temperature for pure zirconium has been determined by many investigators1-5 using metallography, electrical resistivity measurements, and dilatometry. The effect of the rate of cooling on the transformation temperature of zirconium has been studied by Hayes and Kaufmann6 and Duwez,7 and the effect of alloying elements by pfei18 and McGeary.13 Since the development of Zircaloy-2, the limits of the a + ß region for that alloy have been also determined. The first reported temperature for the a — a + a transformation in Zircaloy-2 was 900°C and for a + ß - ß 1000C Subsequent studies by Picklesimer and damson" indicated the beginning of the transformation at 810°C, and the metallographic study by the Technology Group of the Special Materials Section at the Westinghouse Bettis plant1' suggested that 820°to 830°C is the temperature of transformation. The dilatometric investigation by the latter group yielded 830°C for the beginning of the transformation. Thomas and Forscher12 set the beginning of the transformation at 900 °C on heating and the end of the transformation at 870°C on cooling. The above investigators stated in their paper that the dilatometric curve exhibits features caused by a eutectoid reac-

Jan 1, 1962

By Arthur O. Gates

RittingeR's law of the energy expended in crushing is, as roughly stated by Profcssor Richards,' that the work of crushing is proportional to the reduction in diameter; or, as I have more fully expressed it: "The work done in crushing is proportional to the surface exposed by the operation; or, better expressed for this purpose, the work done on a given mass of rock is proportional to the reciprocal of the diameter of the final product—assuming that all the mass has been reduced to one exact sine, which is only theoretically possible."² Kick's law is stated by H. Stadler as follows :3 "The energy required for producing analogous changes of configuration of geometrically similar bodies of equal technological state varies as the volumes or weights of these bodies." In other words, the energy expended is proportional to the volume reduction, instead of the diameter reduction. That these two laws would give widely different results may be shown by a simple imaginary case. A ton of 16-in. cubes is broken to 1-in. cubes at the first operation, and these are broken to 1/16. cubes at a second operation. Since the first operation produces only one-sixteenth as much new surface as the second, the ratio of energy expended in the two operations would be by Rittinger's law as 1 to 16. By Kick's law, since the volume-reduction ratio is the same in both cases, the ratio of energy would be 1 to 1. This discrepancy is great enough to challenge a test by actual experiment, of which there has been, hitherto, but little compared with the amount of argument. The present paper is the record

Jan 1, 1916

By E. Topuz, S. S. Bhamidipati, M. Bartkoski

Air Leakage in underground mines is the most common cause of inefficient distribution of ventilating air. Depending upon various factors, more than one half of the fresh air entering a mine short-circuits to the return airways before reaching the working faces. Consequently, large leakages create an additional demand for increased intake air, which substantially affects the efficiency of a mine system. This paper deals with the identification of the physical variables of air leakages and offers an overview of the methods of measuring leakage.

Jan 1, 1982

By J. H. Allen

The air lift method of pumping water is discussed. A review of several large diameter hole drilling projects that used reverse- circulation air-lift techniques is presented. Proposals are made for reverse circulation flow rates for slow rates of bit penetration (5 fph) as well as reverse-circulation flow rates for faster rates of bit penetration (10 fph). The Ingersoll-Rand air lift equations are modified for rotary drilling operations. By establishing minimum reverse circulation flow rates and utilizing the modified air lift equations, the establishment of minimum circulation equipment sizes and a more definitive requirement for improved bit body design should result.

Jan 1, 1978

By Earl W. Palmer, Cyril Stanley Smith

A study of the precipitation-hardening of copper steels1 led the authors to investigate malleable iron containing copper, for the low-carbon ferritic matrix in malleable iron should lend itself admirably to precipitation-hardening. It was soon found that in addition to rendering malleable iron susceptible to improvement by precipitation-hardening treatments, copper has another potentially useful effect as an accelerator of graphitization. Brief mention of these effects was given in a general paper by Lorig and one of the present authors2; the present paper gives further details on the graphitization and precipitation-hardening effects only. After the completion of this work a paper by L. Lykkin3 appeared, confirming the authors' conclusions regarding graphitization. Material Used After some preliminary heats had been made in the laboratory to determine the effect of copper, several castings from commercial air-furnace heats were obtained, and data from these alone are given here. Part of the metal was poured directly and part was treated in the ladle with the desired amount of copper before pouring. Green-sand molds were used, each holding two tensile test pieces of the form adopted by the Malleable Iron Research Institute, or two bars for graphitization studies, 5/8 in, in diameter and 9 in. long, fed through two enlarged sections equidistant from the middle and ends of the bars. Risers of suitable size insured sound castings. Tensile tests were made on the castings after commercial mallealleizing and after special heat treatments to be described. The analyses of the white irons are given in Table 1.

Jan 1, 1935

By Cyril Stanley Smith, Earl W. Palmer

A study of the precipitation-hardening of copper steels1 led the authors to investigate malleable iron containing copper, for the low-carbon ferritic matrix in malleable iron should lend itself admirably to precipitation-hardening. It was soon found that in addition to rendering malleable iron susceptible to improvement by precipitation-hardening treatments, copper has another potentially useful effect as an accelerator of graphitization. Brief mention of these effects was given in a general paper by Lorig and one of the present authors2; the present paper gives further details on the graphitization and precipitation-hardening effects only. After the completion of this work a paper by L. Lykkin3 appeared, confirming the authors' conclusions regarding graphitization. Material Used After some preliminary heats had been made in the laboratory to determine the effect of copper, several castings from commercial air-furnace heats were obtained, and data from these alone are given here. Part of the metal was poured directly and part was treated in the ladle with the desired amount of copper before pouring. Green-sand molds were used, each holding two tensile test pieces of the form adopted by the Malleable Iron Research Institute, or two bars for graphitization studies, 5/8 in, in diameter and 9 in. long, fed through two enlarged sections equidistant from the middle and ends of the bars. Risers of suitable size insured sound castings. Tensile tests were made on the castings after commercial mallealleizing and after special heat treatments to be described. The analyses of the white irons are given in Table 1.

Jan 1, 1935

By R. G. Robins

The processing of gold bearing sulphide minerals which contain arsenopyrite and various complex arsenic sulphides results in arsenic containing emissions and effluents which are suspect in relation to clean air and clean water standards. Removal of arsenic from gaseous emissions is briefly reviewed. The use of lime to stabilise aqueous residues as either calcium arsenate or calcium arsenite is shown to be inadequate for long term disposal since both compounds are converted into calcium carbonate due to the influence of carbon dioxide in the atmosphere. Mixed calcium arsenate-phosphate residues are similarly unstable, but present better stability than the straight calcium compounds. Alternative disposal methods are reviewed whereby the arsenic is converted to more stable compounds, such as barium arsenate, titanium (IV) arsenate, and arsenic sulphide.

Jan 1, 1984

By H. L. Miaw, A. M. Gaudin, D. W. Fuerstenau

A quantitative method for evaluating density of slime coatings has been developed and applied to formation of iron oxide slime coatings on quartz and on corundum. Slime coating density is related to flotation recovery and to properties of the electrical double layer at mineral surfaces. IN spite of considerable study, the nature of slime coatings in flotation is still not completely understood. However, phenomena that control floc-culation and dispersion of colloidal systems are now interpreted in terms of electrical double layers.",' Colloids will flocculate even though the particles carry the same charge, but when two dispersed colloids of opposite charge are mixed. flocculation ensues even more rapidly. Analogous phenomena seem responsible for slime coating on minerals in flotation systems. To shed new light on the issue it was considered desirable to devise a tool that would measure slime coatings. The usual method has been to examine photographs of presumably representative surfaces, after. an intervening washing in running water. But such an examination is non-quantitative, and the changes in chemical environment represented by the washing may have removed the slime coatings that existed during flotation. To provide the possibility for a correlation with electrical double layer phenomena, the experiments were made with quartz, corundum, and iron oxide, for which elec-trokinetic data are available.'-" Since the properties of the electrical double layers of these oxides depend on the pH of the solution, pH will be the most important variable. Furthermore, because the zero point of charge for silica, iron oxide, and alumina occurs at pH 3.7, 8, and 9.5, respectively, the relative charge on the slime and mineral can be changed over wide ranges. Because of its practical importance in quartz flotation, iron oxide powder was chosen as the slime. Also, its uniform composition, contrasting color, and ease of analysis make experimentation simple. In this investigation, correlation was sought between the effect on flotation recovery of slime addition and slime coating density. Materials and Methods Details are available in a thesis by Miaw." The quartz was selected from pure Brazilian crystalline quartz, crushed, sized (65/150 mesh) acid-cleaned, washed, and stored in conductivity water. The corundum (synthetic alumina of high purity prepared by Linde Co., Chicago) was crushed, sized (65/100 mesh) deslimed, boiled in nitric acid, washed, and stored in conductivity water. The iron oxide slime, reagent-grade ferric oxide (—400 mesh) from Allied Chemical & Dye Corp., was heated to 160°C, cooled, and stored in a vacuum desiccator. In the electron microscope the slime particles appeared to be about 0.3µ in size, but their large specific surface (87,900 cm per g, by gas-adsorption method, using krypton) suggests that the actual particles are smaller than 0.3r. Had they been perfect nonporous spheres, they would have had a diameter of 0.13µ.

Jan 1, 1959

By John Gillie

Prior to the year 1902 electricity was used in the Butte district only for lighting, for the tramming of ores on the surface, and for the electrolytic refining of copper. In that year the Canyon Ferry hydro-electric plant on the Missouri river, with a transmission line to Butte and Anaconda, was completed, and enabled the mining operators to purchase electric current in large quantities at reasonable rates, and its application and use in the various mining operations and reduction works proceeded rapidly. The principal applications. of electric current in metal mining may be listed as follows: Compressing air for hoisting. Compressing air for rock drills and pneumatic tools. Pumping. Ventilating. Lighting. Tramming. Compressing air for blast furnaces and converters Running shop and miscellaneous motors.

Jan 9, 1913

By C. M. Nickerson

It is apparent that repressuring of the oil measures is becoming increasingly important to the oil industry, and is a matter that warrants the best efforts of the petroleum engineer charged with applying this method of operation to a producing property. Considerable attention has been directed to repressuring in various California oil fields, such as Dominguez and Seal Beach, which have served to sell the more progressive operator on this idea and also to keep him sold. The projects that have received most attention are in comparatively young fields where the fluid levels are high, the wells, perhaps, still flowing, where the wet gas production is of considerable volume, and where there is vital need of immediate conservation of gas, which otherwise would be blown to the air. The new State of California Gas Law, which prohibits the waste of gas, has served to interest the oil industry in means of conserving the gas that is now being blown to the air because of lack of markets. This vitally affects the operator in the older, well-depleted oil fields of the state, because in many cases he has a limited market for gas, on account of the flush production from the more active oil fields. While the waste of gas is relatively small in these older fields, such as the Midway-Sunset area, it now attains considerable importance, since under the new State Gas Law it must be put to some bcneficial use. Repressuring in the older fields of California has not received the attention of the petroleum engineers that is warranted by the present situation. This paper was prepared with the view of presenting the salient features connected with repressuring in the well-depleted oil measures of the older fields, and to show what results have already been obtained in these fields by injecting the unmarketable gas into the sands, particularly in the Midway-Sunset field in the San Joaquin Valley of California. Other projects in the older fields of the state offer some supporting data in this connection, such as the Shields Canyon and the Brea Canyon fields. Gas Storage and RepressuRing On account of the lack of market for a large portion of the dry gas produced in certain of the older, well-depleted oil fields of California, the

Jan 1, 1930

By C. W. Lawr

The ores mined by the Santa Gertrudis Co. at Pachuca, Mexico, arc mainly silver-bearing; they also yield some gold and carry a little copper. Strong cyanide solutions are used to dissolve the silver and gold, and the mechanical loss of cyanide at the tailings filter has been considerable. Prior to the year 1923, the pulp, after agitation, was given a 35 to 37-min. wash with barren solution in a Butters-type leaf filter; the discharged slime cake was repulped and pumped into eight Merrill self-sluicing slime presses in which the slime was given a further wash with barren solution for 25 to 35 min., followed by a 10-min. water wash. At that time the barren solution titrated around 0.350 per cent. free KCN and 0.500 per cent. total KCN. (Aero brand cyanide is used.) It can readily be seen that a 10-min. water wash would leave considerable cyanide in the filter cake, which of course was a total loss. This averaged 0.522 kg. (1.15 Ib.) KCN per ton of solution. As the daily discharge to the dam was 1600 tons' of slime of a 2:1 ratio of liquid to solid, the value of this mechanical loss of cyanide was an important item and it's recovery held alluring possibilities. Principle of Cyanide-recovery Process As it had acquired the patent rights to theLayng (H. R.) and Halvor-sen (A. L.) processes, also those of Mills (L. D.) and Crowe (T. B.) after considerable experimental work in its own laboratory and at Tonopah, Nev., The Merrill Company of San Francisco early in 1923 notified the Mexican Corporation and compania de Santa Gertrudis of its process for the recovery of cyanide from weak wash solutions, or for the transference of cyanide from a foul mill solution to a clean alkaline solution. This method is known as the Mills-Crowe process, the principle of which is as follows: The solution from which the cyanidc is to be removed is made acid by bringing it into contact with sulfur dioxide (SO2). The acidified solution is the; transferred to a closed tank in which air and solution are brought into intimate contact. The air leaving the tank charged with HCN is then passed to another tank in which it is mixed with an alkaline solution,

Jan 1, 1930