Search Documents

By Edward L. Clark, Garrett A. Muilenburg

THE first record of the discovery of iron ore in Missouri was Marquette's observation in 1673 of brown iron ore, or limonite, in the Mississippi River bluffs just north of the mouth of Apple Creek in southeastern Perry County. There is no record of any attempt to mine or smelt Missouri iron ores until 1815, when the Ashebran furnace was erected at the Stouts Creek shut-in near Arcadia, Iron County. Some limonite was treated in this furnace, the first iron furnace west of Ohio, but most of the ore was hematite from Shepherd Mountain and adjacent deposits. Eight years later, in 1823, the Perry furnace five miles north of Caledonia, Washington County, was constructed to smelt limonite ore. It was not until 1890 to 1900, however, that these ores attracted considerable attention. Nearly 300,000 tons had been produced by 1911, and this production had come from 24 counties in the Ozark region. For the next two decades, until 1931, essentially all activities ceased. During the depression years of the thirties when employment was low many people turned to the brown ores for subsistence; consequently production was increased. World War II produced another stimulus to the industry. The availability of risk capital in the past three years has revived interest in these deposits, although no appreciable increase in production has resulted.

Jan 1, 1954

By R. Clare Coffin

The production of petroleum in the Rocky Mountain district increased from 27,104,436 bbl. in 1929 to 33,048,630 bbl. in 1930. This increase was due to the development in southeastern New Mexico; which is in reality a portion .of the West Texas province. Disregarding production in southeastern New Mexico, the Rocky Mountain district produced 25,799,027 bbl. in 1929 and 23,164,988 bbl. in 1930, a decrease of 2,634,039 bbl. for the period. The daily production in January, 1930, averaged 70,839 bbl. for the entire district and in December, 1930, the daily production was 98,995 bbl. Total production by states is given in Table 1. Three important discoveries of oil and one of gas occurred in the district during 1930 in structures not, previously known to contain oil or gas. Oil was discovered in Dry Creek structure, Carbon County, Mont.; in the Midway structure, Natrona County, near Casper, Wyo.; and in the Greasewood structure, Weld County, Colo., northwest of Fort Morgan. Gas was discovered in the Bell Rock structure in Moffat County, western Colorado. Seven deep tests in as many different fields encountered oil in lower horizons than those already exploited. All of these discoveries were in the state of Wyoming. They occurred in the Salt Creek field, Natrona

Jan 1, 1931

By Frederic Lahee

THE purpose of this paper is to demonstrate the similarity of the oil-producing structures in the Mexia1 fault zone, and to show how the apparently very irregular well logs in these fields may be used for the practical interpretation of subsurface conditions. The Mexia oil field, in Limestone County, Tex. (Fig. 1) is closely associated with a fault that trends about 30° east of north and has a displacement of between 200 and 400 ft., with downthrow on the west. Minor slips accompany this major fault, some being roughly parallel to the main break while others are transverse to it. These faults belong to the so-called Mexia fault zone, a belt of fracturing that has been traced in its characteristic features southward to near Kosse, 15 miles south of Groesbeck, in southern Limestone County, and northward at least as far as the Trinity river at the eastern border of Navarro County, and possibly as far north as Hunt and Hopkins counties.2 The Balcones fault zone, from 30 to 40 miles west of the Mexia fault zone, differs from the latter in that its principal displacement is a down-throw on the east. In this respect, it is exactly the opposite of the Mexia displacement. Between these two zones of major faulting lies a great down-dropped block, or graben, which is broken by numerous minor faults.

Jan 2, 1925

By Henry S. Rawdon

The relation between the course, or path, of the fracture of metals and alloys, produced in service or as a result of certain laboratory tests, and the crystalline units of which such materials are composed is of utmost importance. The fracture of normal material is, in general, intracrystalline, i.e., it consists of a break across the grains rather than of a separation between them. An interorystalline fracture indicates either that the metal is of very inferior quality or that the break occurred under very unusual conditions, e.g., at a very high temperature. The usual mechanical tests, when applied to metals of the type that breaks with an intercrystalline fracture, merely measure the coherence of adjacent grains for one another and reveal little as to the real properties of the metal itself. Even such a soft plastic substance as lead, under suitable conditions, may be rendered so weak and brittle that the metal can be easily crumbled into powder by the fingers although the constituent grains have lost none of the intrinsic properties of lead. Various erroneous explanations of this behavior of lead have appeared in the scientific literature, the change being described usually as an allotropic one. The importance, in an industrial sense, of a proper explanation of this type of the corrosion of lead justifies the description of the type of metal deterioration that follows. Corroded Lead Sheathing In Figs. 1 and 2 are shown two typical specimens of corroded lead sheathing selected from materials submitted to the Bureau of Standards for examination. Fig; 1 shows a section of the sheathing of an aerial cable; Fig. 2, that of the lead covering of a subterranean feeder-line of an electric light system. In this case the deterioration had proceeded to a much great'er extent than in the case shown in Fig. 1 so that certain portions of the metal could easily be crumbled into a coarse gray powder by the fingers. This was particularly true of those portions of the sheathing

Jan 1, 1921

By A. L. Marshall, F. J Norton

The object of this investigation was to make a comprehensive study of the degassing of molybdenum in order to determine how rigorous a treatment was necessary to completely remove sorbed gases from molybdenum electrodes in vacuum tubes. Some work has also been done with tungsten, nickel, iron and carbon. As a logical development of this work it has been shown that the gas is present throughout the body of the metal and a study has been made of the solubility of nitrogen in molybdenum and tungsten and the rate, of diffusion of nitrogen through molybdenum has been calculated. Tests were made on molybdenum from all the commercial sources and no difference was discovered in the nature of the gases present, the amounts or the ease of removal. The reason for this was apparent when a study was made of the manner in which gases are absorbed by gas-free molybdenum. It is necessary to heat molybdenum to 1760°C. in a vacuum of the order of 0.001 micron for a time which varies lineally with the thickness, in order to obtain a condition in which no further gas is evolved by the sample. A sample so degassed can be handled and subsequently assembled in a tube and then degassed readily. The gases obtained from molybdenum are carbon monoxide and nitrogen, the nitrogen being the more difficult to remove. Apparatus and Technique The apparatus is shown in Figs. I and 2. It consisted of two units, a degassing system and an analytical system. Each had a bake-out oven, as shown surrounding the systems in the sketches. The system , will be traced, starting from the sample in the degassing system. A water-cooled quartz chamber surrounded the sample. The high-frequency coil, which heated the sample, extended only around this chamber and was cooled by an air blast. High-frequency power of 1800-meter wave length was obtained from a self-rectifying oscillator circuit with a maximum power input of 20 kw. A graded seal connected the quartz to the rest of the apparatus, which was of hard glass. The temperature of the molybdenum sample was observed by an optical pyrometer through an optical window about 40 cm. distant from the sample. Since the object viewed under these conditions was not a black body, true temperature was not observed, but the so-called "brightness temperature." The correction of this to true temperature is discussed in a later section. The apparatus was taken apart just above the graded seal; the quartz chamber was slipped off, washed with nitric acid, water and alcohol, and dried by an air stream. The old sample was removed by unscrewing the lower nut, and the new

Jan 1, 1944

By A. L. Marshall, F. J. Norton

The object of this investigation was to make a comprehensive study of the degassing of molybdenum in order to determine how rigorous a treatment was necessary to completely remove sorbed gases from molybdenum electrodes in vacuum tubes. Some work has also been done with tungsten, nickel, iron and carbon. As a logical development of this work it has been shown that the gas is present throughout the body of the metal and a study has been made of the solubility of nitrogen in molybdenum and tungsten and the rate, of diffusion of nitrogen through molybdenum has been calculated. Tests were made on molybdenum from all the commercial sources and no difference was discovered in the nature of the gases present, the amounts or the ease of removal. The reason for this was apparent when a study was made of the manner in which gases are absorbed by gas-free molybdenum. It is necessary to heat molybdenum to 1760°C. in a vacuum of the order of 0.001 micron for a time which varies lineally with the thickness, in order to obtain a condition in which no further gas is evolved by the sample. A sample so degassed can be handled and subsequently assembled in a tube and then degassed readily. The gases obtained from molybdenum are carbon monoxide and nitrogen, the nitrogen being the more difficult to remove. Apparatus and Technique The apparatus is shown in Figs. I and 2. It consisted of two units, a degassing system and an analytical system. Each had a bake-out oven, as shown surrounding the systems in the sketches. The system , will be traced, starting from the sample in the degassing system. A water-cooled quartz chamber surrounded the sample. The high-frequency coil, which heated the sample, extended only around this chamber and was cooled by an air blast. High-frequency power of 1800-meter wave length was obtained from a self-rectifying oscillator circuit with a maximum power input of 20 kw. A graded seal connected the quartz to the rest of the apparatus, which was of hard glass. The temperature of the molybdenum sample was observed by an optical pyrometer through an optical window about 40 cm. distant from the sample. Since the object viewed under these conditions was not a black body, true temperature was not observed, but the so-called "brightness temperature." The correction of this to true temperature is discussed in a later section. The apparatus was taken apart just above the graded seal; the quartz chamber was slipped off, washed with nitric acid, water and alcohol, and dried by an air stream. The old sample was removed by unscrewing the lower nut, and the new

Jan 1, 1944

By Benjamin F. Tillson

The hammer drill rightly receives the credit for having made the one-man drill possible, and so many economies seem possible through the proper application of different types of hammer drills to various mining, quarrying, and excavating operations, that an indication of the 'economies effected by the New Jersey Zinc Co. at its Franklin mines may be of pertinent interest. When this company commenced its trials of hammer drills in 1907, these tools had not been developed to one-fourth the capacity and refinement which they have at present. At that time it was frequently stated that such a small tool, drilling holes of less diameter than the reciprocating rock drill, could not drill enough holes in a shift to permit the placing of sufficient explosive to break a tonnage of ore comparable with that produced by the "rock drills;" that the placing of small holes inclined upward, at angles steeper than 40' above the horizontal, could not be expected to produce results equal to the large flat, wet or dry, holes in the breasted back of an overhand stope, and would only shatter the ground so as to make the back unsafe. In spite of these adverse opinions, the hammer drills first showed their superiority over both heavy and light reciprocating drills in raising and in stoping, and then in drifting and quarry work. As a result, all of the reciprocating drills at the Franklin mines were scrapped three years ago, all of the mining work being accomplished with increased efficiency, as shown in detail in this article. With the advent of the hammer drill in this property, it was considered advisable to make comparative tests of all the tools accessible, and it has since been the policy to investigate the merits of any advance of the drilling art in order to get the maximum amount of work from the tools. The necessity of devising some means of standardizing drill tests, and of measuring the consumption of compressed air as well as the drilling speed, was early realized. The common test was to fill a measured air receiver with compressed air at a certain gauge pressure, run the drill until the pressure had dropped to too low a figure, then compute from the time, drop in pressure, and

Jan 1, 1915

By Danforth R. Hale

Minerals for electronic and optical uses divide easily into two sections: (1) quartz and (2) minerals other than quartz. Quartz Quartz, having a great usefulness discovered by the radio communication enthusiasts about 1918, has become a subject of amazingly expanded interest in the U.S. over the past decade as a man-made mineral and a $3 million crystal-growing business. An economic summary of the commercial growing of quartz crystals has a place in a handbook directed to the mineral engineering industry when it is remembered that quartz crystals have long been an important commercial mineral, and that the raw material for “cultured quartz”- that is to say, quartz crystals grown through the ingenuity of man-is still natural quartz. Nearly all the natural crystals come from Brazil. The larger pieces which meet rigorous standards of quality are used for electronic and, to a lesser extent, optical components. Smaller pieces and fragments are used for vitreous silica. The need for high quality material in quantity led to U.S. government-sponsored research programs in the 1940s that have resulted in the factory growing of beautiful crystals of prescribed shape, size, and quality. The development of the cultured quartz crystal is typical of man's success in adapting the product of the mine to increasingly sophisticated uses. A remarkable achievement perhaps, but foreshadowed by experiments in 1908 by Giorgio Spezia (1908), an Italian geologist studying the relative effects of temperature and alkaline environment on the solubility of quartz. Modern radio equipment is most often controlled as to frequency by the presence in the circuit of a separately added "crystal"-the 1918 discovery responsible for the existence and growth of the quartz industry. The "crystal" is quartz, but this component is a carefully oriented and prepared slice from a crystal, but not a crystal as recognized by a rock hound or seen in a museum. How quartz operates to control frequencies is not a proper subject for a handbook on industrial minerals, and references should be consulted (Cady, 1964; Mason, 1964). Quartz belongs to that class of materials called dielectrics: those that do not conduct an electric current but permit electric fields to exist and act across them. Quartz shows the "piezo-electric effect," which means that when a quartz plate is mechanically deformed against its natural stiffness, one of its surfaces becomes negatively charged, the other, positively charged. When the plate is released from the stress quickly, the charges disappear as the plate regains its original shape, but because of mechanical momentum the plate deforms in the opposite direction (to a lesser amount) and the surfaces correspondingly become charged in the opposite direction. By coating the two surfaces thinly with metal and attaching flexible wires, these charges may be brought into an electronic circuit. If the surfaces are suddenly electrically charged by movement of current through the wires, the "converse piezoelectric effect" occurs -the plate deforms. Carry the thought further and it is realized that an alternating current flowing through the wires responds to the mechanical oscillation of the plate and is keyed to this oscillation. By controlling the thickness of the plate its mechanical vibration frequency can bevaried through a wide range. One type of quartz plate, called the AT-cut, having a precisely defined orientation with respect to the crystallographic axes of the crystal, vibrates on a microscopic scale much as a book would deform when placed flat on a table and the top cover moved parallel back and forth with the hand. There are at least 17 other orientations which have been studied, some of

Jan 1, 1975

By J. H. Swisher

When an Fe-Mn alloy is internally oxidized, the inclusions formed are MnO which contains some dissolzled FeO. In the internal oxidation reaction, not all of the manganese is oxidized; some remains in solid solution as a result of the high Mn-0 solubility product in iron. Taking these factors into consideration, the rate of internal oxidation of an Fe-1.0 pct Mn alloy is computed as a function of temperature, using available thermodynanzic data and recently published data for the solubility and diffusivity of oxygen in iron. The predicted and experimentally determined rates for the temperature range from 950 to 1350°C are in good agreement. ThE rates of internal oxidation of austenitic Fe-A1 and Fe-Si alloys have been studied extensively.1"4 Schenck et al. report the results of a few experiments with Fe-Mn alloys at 854" and 956C, and Bradford5 has studied the rate of internal oxidation of commercial alloys containing manganese in the temperature range from 677" to 899°C. When Fe-Mn alloys are internally oxidized, the inclusions formed are solutions of FeO in MnO, the composition depending on the experimental conditions. Since the thermodynamics of the Fe-Mn and FeO-MnO systems have been investigated,6"9 and since the solubility and diffusion coefficient of oxygen in y iron have been determined recently,' it is possible to predict the rate of internal oxidation from known data. The calculations used in predicting the rate of internal oxidation will first be outlined, then the results of the prediction will be compared with the experimental results of this investigation. PREDICTION OF PERMEABILITY FROM THERMODYNAMIC AND DIFFUSIVITY DATA Oxygen is provided for internal oxidation in these experiments by the dissociation of water vapor on the surface of the alloy. The dissociation reaction is: + H2(g) + [O] [1] where [0] denotes oxygen in solution. The equilibrium constant for this reaction is known as a function of temperature:' log As oxygen diffuses into the alloy, oxide inclusions are formed which are MnO with some FeO in solid solution. The reactions occurring are: [Mn] + [0] = (MnO) [31 and [Fe] + [0] = (FeO) [41 where [ Mn] is manganese dissolved in iron and (FeO) is iron oxide dissolved in MnO. The overall reactions may be written as follows: [Mn] + HOte) = (MnO) + H2(£) [5] and [Fe] + H20(g) = (FeO) + Hz(R) [61 The standard free-energy changes and equilibrium constants for Reactions [5] and [6] are known.6 Therefore the equilibrium constants for Reactions [3] and [4] may be obtained by combining known thermodynamic data for Reactions [I], [5], and [6]. For Reactions [3] and [4]: K = and For the present purpose, both the Fe-Mn7,8 and FeO-~n0' systems can be considered to be ideal, i.e., [amn] = [NM~] and (aFeO) = (NM~~) = 1 - (NFeO) where the Ns are mole fractions. These relations, together with Eqs. [I] and [8], permit us to compute both the oxide and metal compositions as a function of temperature and oxygen potential at any point in the specimen. For cases where the oxygen concentration gradient between the surface and the subscale-base metal interface is linear, the kinetics of internal oxidation is an application of Fick's first law: where dn/dt is the instantaneous flux of oxygen into the specimen, g-atom per sq cm sec; 6 is the instantaneous thickness of the subscale, cm; Do is the diffusion coefficient of oxygen in iron, sq cm per sec; p is density of iron, g per cu cm; h[%O] is the oxygen concentration difference between the surface and sub-scale-base metal interface, wt pct. B6hm and ~ahlweit" derived an exact solution to the diffusion equation for systems in which there is a stoichiometric oxide formed. They showed that the oxygen concentration gradient is given by a rather complex error function relation. For the Fe-Mn-0 system and for most other systems that have been studied, however, variations in oxide compositions are small and rates of internal oxidation are sufficiently slow that the deviation from linearity in the concentration gradient of oxygen is negligible. The mass of oxygen transported across a unit area of the specimen for the total time of the experiment is given by the mass balance equation:

Jan 1, 1969

By C. C. Wright, T. S. Spicer

A characteristic property of bituminous coal is that upon being heated the coal becomes plastic, evolves volatile gases, and finally solidifies into coke. This fundamental characteristic is of utmost importance and is utilized in the production of the high-temperature coke upon which the steel industry is so dependent; but from the standpoint of operation in the domestic underfeed stoker this coking tendency seriously interferes with efficient combustion. When the coke formed has too strong a structure, certain difficulties result, such as low rate of burning, slow response to heat demand, and, in extreme cases, extinction of fire. The plastic mass prevents uniform distribution of air through the fuel bed and, with strongly coking coals, large dense pieces of coke are produced which have much less reacting surface than was possessed by the original coal. In both ignition and combustion of solid fuels, the extent of the reacting surface is an accelerating factor. Poor combustion permits a surplus of fuel to accumulate in the furnace because the rate of feed and the rate of combustion are not in equilibrium, and this produces an unbalanced condition detrimental to continued automatic service. In order to bum strongly coking coals satisfactorily in a conventional stoker during the three requisite types of operation—continuous, intermittent and hold-fire, frequent attention is necessary. Domestic stokers are defined by the industry as residential stoker heaters that burn 60 lb. of coal or less per hour. With a few exceptions, these units employ the underfeed principle of combustion in which both air and coal move in the same direction up and through the fuel bed. Domestic combustion equipment has difficulty in meeting the problems presented by the several variations in ash and volatile matter, in ash-clinkering tendencies, in coking properties, and in the particle size of bituminous coals. The work of Bituminous Coal Research Inc. at Battelle Memorial Institute has shown that, of these, coking characteristics and the clinkering tendencies have the greatest effect upon the operation of the conventional clinkering type of stoker. Typical coke formations in a clinkering type of underfeed domestic stoker are illustratcd in Fig. I, which shows (A) the ideal fuel bed obtained with a noncoking or free-burning coal; (B) the type of fuel bed formed with a coal that produces a weak coke; and (C) the type of fuel bed obtained with a strongly coking coal. C is characteristic of the fuel bed developed when the average Pennsylvania bituminous coal is burned in an underfeed stoker of conventional type. It is apparent from these pictures that the formation of coke trees will seriously interfere with the efficient automatic combustion of Pennsylvania bituminous coals.

Jan 1, 1942

By T. S. Spicer, C. C. Wright

A characteristic property of bituminous coal is that upon being heated the coal becomes plastic, evolves volatile gases, and finally solidifies into coke. This fundamental characteristic is of utmost importance and is utilized in the production of the high-temperature coke upon which the steel industry is so dependent; but from the standpoint of operation in the domestic underfeed stoker this coking tendency seriously interferes with efficient combustion. When the coke formed has too strong a structure, certain difficulties result, such as low rate of burning, slow response to heat demand, and, in extreme cases, extinction of fire. The plastic mass prevents uniform distribution of air through the fuel bed and, with strongly coking coals, large dense pieces of coke are produced which have much less reacting surface than was possessed by the original coal. In both ignition and combustion of solid fuels, the extent of the reacting surface is an accelerating factor. Poor combustion permits a surplus of fuel to accumulate in the furnace because the rate of feed and the rate of combustion are not in equilibrium, and this produces an unbalanced condition detrimental to continued automatic service. In order to bum strongly coking coals satisfactorily in a conventional stoker during the three requisite types of operation—continuous, intermittent and hold-fire, frequent attention is necessary. Domestic stokers are defined by the industry as residential stoker heaters that burn 60 lb. of coal or less per hour. With a few exceptions, these units employ the underfeed principle of combustion in which both air and coal move in the same direction up and through the fuel bed. Domestic combustion equipment has difficulty in meeting the problems presented by the several variations in ash and volatile matter, in ash-clinkering tendencies, in coking properties, and in the particle size of bituminous coals. The work of Bituminous Coal Research Inc. at Battelle Memorial Institute has shown that, of these, coking characteristics and the clinkering tendencies have the greatest effect upon the operation of the conventional clinkering type of stoker. Typical coke formations in a clinkering type of underfeed domestic stoker are illustratcd in Fig. I, which shows (A) the ideal fuel bed obtained with a noncoking or free-burning coal; (B) the type of fuel bed formed with a coal that produces a weak coke; and (C) the type of fuel bed obtained with a strongly coking coal. C is characteristic of the fuel bed developed when the average Pennsylvania bituminous coal is burned in an underfeed stoker of conventional type. It is apparent from these pictures that the formation of coke trees will seriously interfere with the efficient automatic combustion of Pennsylvania bituminous coals.

Jan 1, 1942

By T. S. Spicer, C. C. Wright

A CHARACTERISTIC property of bituminous coal is that upon being heated the coal becomes plastic, evolves volatile gases, and finally solidifies into coke This fundamental characteristic is of utmost importance and is utilized in the production of the high-temperature coke upon which the steel industry is so dependent, but from the standpoint of operation in the domestic underfeed stoker this coking tendency seriously interferes with efficient combustion When the coke formed has too strong a structure, certain difficulties result, such as low rate of burning, slow response to heat demand, and, in extreme cases, extinction of fire The plastic mass prevents uniform distribution of air through the fuel bed and, With strongly coking coals, large dense pieces of coke are produced which have much less reacting surface thin was possessed by the original coal In both ignition and combustion of solid fuels, the extent of the reacting surface is an accelerating factor Poor combustion permits a surplus of fuel to accumulate in the furnace because the rate of feed and the rate of combustion are not in equilibrium, and this produces an unbalanced condition detrimental to continued) automatic service In order to burn strongly coking coals satisfactorily in a conventional stoker during the three requisite types of operation continuous, intermittent and hold-fire, frequent attention is necessary Domestic stokers are defined by the industry as residential stoker heaters that burn 60 lb of coal or less per hour With a few exceptions, these units employ the underfeed principle of combustion in which both air and coal move in the same direction up and through the fuel-bed Domestic combustion equipment has difficulty in meeting the problems presented by the several variations in ash and volatile matter, in ash-clinkering tendencies, in coking properties, and in the particle size of bituminous coals The work of Bituminous Coal Research Inc at Battelle Memorial Institute has shown that, of these, coking characteristics and the clinkering tendencies have the greatest effect upon the operation of the conventional clinkering type of stoker Typical coke formations in a clinkering type of underfeed domestic stoker are illustrated in Fig. I, which shows (A) the ideal fuel bed obtained with a noncoking or free-burning coal, (B) the type of fuel bed formed -with, a coal that produces a weal coke, and (C) the type of fuel bed obtained with a strongly coking coal C is characteristic of the fuel bed developed when the average Pennsylvania bituminous coal is ,burned in an underfeed stoker of conventional type It is apparent from these pictures that the formation of coke trees will seriously interfere with the efficient automatic combustion of Pennsylvania bituminous coals

Jan 1, 1942

By W. C. Elli, M. E. Fine

YOUNG'S modulus of elasticity in metals ordinarily decreases with rising temperature. The range of the thermoelastic coefficient at room tem- 1/E dE/dT perature (temperature coefficient of modulus, is illustrated1 by the values for tungsten and hard-drawn aluminum, —95 and —1220x10-6 eg C-1. However, a nearly zero thermoelastic coefficient is observed in some ferromagnetic alloys over a limited temperature range. In these alloys, as the temperature is raised, an increase in modulus arising from loss of ferromagnetism compensates the normal decrease. Iron-nickel alloys containing 36 to 52 pct Ni behave in this manner. In the present investiga- tion, the dependence of the modulus and thermo-elastic coefficient on cold working and annealing were studied in iron-nickel alloys in this range of nickel. Although these alloys, when fully annealed, have a coefficient near zero over a very small temperature interval, the temperature range of low coefficient can be extended greatly by straining and then stress-relief annealing. The modulus of face-centered cubic iron-nickel alloys annealed at 1000°C does not vary linearly with composition at room temperature but, as shown by the solid line of fig. 1, from Koster,' is minimum at 40 pct Ni and maximum at 87 pct Ni. The modulus increases with applied magnetic field but retains the minimum near 40 pct Ni. Schematic change of modulus with temperature for three compositions is shown in fig. 2.'. ' With increasing temperature, the slope becomes less negative, goes through zero (temperature of minimum modulus for the alloy), becomes positive, and resumes its normal negative value above the Curie

Jan 1, 1951

By J. E. McDonald, J. G. Eberhart

A model is discussed from which the work of adhcslon .tor liquid transition metals on aluminum oxide surfaces can he calculated, A close-packed (00011 oxygen surface on A12O3 is assumed with two different types of surface sites: one type involving metal-oxygen bonds and the other man der Waals into actions. The work of adhesion is thus expressed as the sum of these two bonsding free energies. Calculated works of adhesion for nickel, titanium, chromium, and zirconium on sapphire agree well with the experimentally determined quantities. The model is extentled to the calculation of the work of adhesion and shear stress required to remove a thin metal film from a sapphire substrate and is in good agreement with experimental values. The obsewed dependence of the work of adhesion on the free energy of oxide formation of the metal is shown to also provide an interpretation of the tittle dependence of thin-film adhesion. THIS paper presents a model for the type of bonding which occurs across a metal-A12O3 interface. The model is used to explain the results of two types of experiments in which such an interface exists: 1) the adhesion of thin metal films on Al2O3 substrates and 2) the wetting of A12O3 by liquid metal drops. The adhesion of thin films to various substrates has been the subject of a variety of investigations.'-' Benjamin and weaver3 and Bowie,6 using the scratch test developed by Heavens,10 studied the adhesion of metallic films to glass substrates. Their observations for noble-metal film adhesion agree well with an adhesion model involving a van der Waals type of bonding between the film and the substrate. For films of metals whose free energy of oxide formation. ?F°f, has a negative value. Benjamin and weaver3 and Bowie6 found a time-dependent adhesion with an initial value that can be interpreted in terms of van der Waals interactions but a larger terminal value which was related to ?F°f, Karnow-sky and Estill7 deposited films on sapphire at elevated temperatures and noticed no time dependence of film adhesion but a similar correlation with ?F°f. Because of the kinetic problems associated with thin-film adhesion it is desirable to examine adhesion in an equilibrium system. The wetting behavior of liquid-metal drops on Al2O3 provides such a system. Systems of this metal-ceramic type have been studied extensively.11 Humenik and Kingeryl2 have measured the wetting of A12O3 (and other substrates) by several metals and have pointed out that the wetting ability of these metals increases with increasing values of -?F°f. It is thus seen that thin-film adhesion and metal wetting on A12O3 are both related to the tendency of the metal to react with the surface oxide ions of the Al2O3 substrate and, because of this, both phenomena should be explainable by an appropriate model for the metal-Al2O3 interfacial bonding. In the sections that follow, wetting and adhesion data on A2O3 are reviewed and a model is presented by which these phenomena can be interpreted. ANALYSIS OF WETTING EXPERIMENTS In an equilibrium system involving a liquid-metal drop on a solid Al2O3 substrate, the work of adhesion, WAD, is defined by the Dupre, equation as WAD = ?s + ?L -?sL [1] where ?s and ?L are the surface free energies of the solid substrate and the liquid drop, respectively, and ?sL is the interfacial free energy. The work of adhesion is the work required to separate a unit area of the solid-liquid interface into two surfaces. The work of adhesion is usually determined from a sessile-drop experiment in which yL and the contact angle, ?, are measured. The Young-Dupr6 equation is then used to calculate WAD Wad = ?L (1+ cos ?) [2] The literature of this subject has been examined and Table I shows work of adhesion data for various liquid metals as measured on A12O3 substrates. The standard free energy of oxide formation of the metal at the temperature of the wetting experiment, ?F°f . is also tabulated in kcal per g-atom of oxygen. The data is grouped according to the gaseous atmos-

Jan 1, 1965

By W. M. Baldwin, J. T. Brown

The effect of hydrogen on the ductility, c, of SAE 1020 steel at strain rates, i, from 0.05 in. per in. per rnin to 19,000 in. per in. per rnin and at temperature, T, from +150° to —320°F was determined. The ductility surface of the embrittled steel reveals two domains: one in which and the other in which The usual "explanations" of hydrogen embrittlement are in accord with the first of these domains only. THE purpose of this investigation was a fuller A characterization of this of the investigation effects of varying temperature and strain rate on the fracture strain of hydrogen-charged steel. To be sure, it is known that low and high temperatures remove the embrittlement that hydrogen confers upon steels at room temperature,1 * see Fig. la and b, and that high strain rates have a similar effect,'-' see Fig. 2a, b, and c. However, the general effect of these two testing conditions on the fracture ductility of hydrogen-charged steels is not known, i.e., the three-dimensional graphical representation of fracture ductility as a function of temperature and strain rate is not known—only two traverses of the graph are available. The need for such a graph is not pedantic. To demonstrate this point, Fig. 3a, b, and c shows three of many three-dimensional graphs, all possible on the basis of the two traverses at hand. The important point (as will be developed in the Discussion) is that each of them would indicate a different basic mechanism for hydrogen embrittlement. It will be noted that the four types of ductility surfaces in Fig. 3a, b, and c may be characterized as follows: Material and Procedure Tensile tests were made at various temperatures and strain rates on a commercial grade of % in. round SAE 1020 steel in both a virgin state and as charged with hydrogen. The steel was spheroidized at 1250°F for 168 hr to give the unembrittled steel the lowest possible transition temperature. The steel was charged cathodically with hydrogen as follows: The specimen was attached to a 6 in. steel wire, degreased for 5 min in trichlorethylene, rinsed with water, and fixed in a plastic top in the center of a cylindrical platinum mesh anode. The assembly was placed in a 1000 milliliter beaker containing an electrolyte of 900 milliliters of 4 pct sulphuric acid and 10 milliliters of poison (2 grams of yellow phosphorous dissolved in 40 milliliters of carbon disulphide). A current density of 1 amp per sq in. was used which developed a 4 v drop across the two electrodes. All electrolysis was carried on at room temperature. Temperatures for tensile tests were obtained by immersing the specimens in baths of water (+70° to + 150°F), mixtures of liquid nitrogen and isopen-tane (+70° to —24O°F), and boiling nitrogen (-240" to-320°F). Specimens were tested in tension at strain rates of 0.05, 10, 100, 5000, and 19,000 in. per in. per min. The 0.05 and 10 in. per in. per rnin strain rates were obtained on a 10,000 lb Riehle tensile testing machine, the 100 in. per in. per rnin rate on a hydraulic-type draw bench with a special fixture, and the 500 and 19,000 in. per in. per rnin rates on a drop hammer. The fracture ductility of hydrogen-charged steel at room temperature and normal testing strain rates (-0.05 in. per in. per min) is a function of electro-lyzing time, dropping to a value that remains constant after a critical time.'* Under the conditions of • The hydrogen content of the steel continues to increase with charging time even after the ductility has leveled off to its saturated value.' this research the saturated loss in ductility occurred at approximately 30 min, see Fig. 4, and a 60 min charging time was taken as standard for all subsequent tests. After charging the steel with hydrogen, the surface was covered with blisters. These have been described by Seabrook, Grant, and Carney.' The original diameter of the specimen was not reduced by acid attack, even after 91 hr. Results The ductility of both uncharged and charged specimens is given as a function of strain rate in Fig. 5, and as a function of temperature at four different strain rates in Fig. 6. These results are assembled into a three-dimensional graph in Fig. 7. It is seen that the locus of the minima in the ductility curves of the charged steels divides the ductility surface into two domains. At temperatures below the minima,

Jan 1, 1955

By V. C. Williams

Some of the physical, chemical, and electrical processes for conversion of saline water to potable or industrial water are economically surveyed from an engineering viewpoint. Since all these processes require energy for drive and equipment for containment, the correlative economic factors are developed which indicate directive influences in the choice of particular regional processes. The supply of natural waters and its distance also affect decision. Any one process will probably not prove dominant in the field because auxiliary considerations such as the saline water source; types and continuing availability of fuel; electric power use or recovery; area economic status and advancement; and the political pressures of population, group demands, and land use tend equivocally to obscure capital and operation cost decisions. Basic engineering considerations, data, and economic factors are presented to assist in the direction of these decisions. An exploding world population, increasing industrialization, advancing standards of living, and the desire of less-privileged nations for betterment focus attention sharply on a major problem: water. *19 Up to now, in retrospect, people have had it relatively easy in the handling of this problem. All the better dams in the most advantageous sites, the better aquifers, the shortest aqueducts have been built. In another phase of the problem, concern is evident that wastes cannot indefinitely be disposed of merely by keeping them dilute and discharging them promiscuously. 7-9 And, perhaps, as past civilizations have done,l5 water, watersheds, streams, and irrigation may have been mismanaged or, at the least, not adequately studied.3,5,36,37 In this last is perhaps the core of the problem. As Gross states, "Ignorance and too often, indifference are contributing factors. Archaeology and theology both furnish ample testimony to the existence of rich lands where deserts now stand; it was man who ravaged his land. Unless education is a companion to water development, development might as well be forgotten. But without water, there is no beginning."13 The U.S. is showing increasing concern about its water for predictions are that by 1980 the daily withdrawals will be 494 billion gal, a figure nearly equal to the dependable supply.Is This is based on a conservative projected population of 230 million. The major categories of withdrawals are: To make available this per capita average of 2150 gal per day will require an expenditure of $219 billion over the next 20 years. The U.S. is not alone in this concern. The United Nations shows as arid zones of the world: all of Africa north of the equator and south of the 20's parallel; all of the Arabian peninsula; all of the middle east and Iran, Iraq, Pakistan, Afghanistan, northern and central India; a great band about 1000 miles wide along the 40'~ parallel from the Caspian Sea east across Russia through China to the Pacific Ocean; all of Australia except the coastal plain; the Caribbean Islands; the western nations of South America; and the western third of the United States and of Mexico. With one quarter of the earth's 57,500,000 sq miles of land thus suffering from lack of good water, increasing attention goes to the treatment of brackish and sea waters. The U.S. has been a leader in this field4,12, 16123,24 through its Office of Saline Water in the Dept. of Interior because even now some of its cities and regions are short of potable water. 11j'7,M Industrial water is also of vital concern as a result of ever higher industrialization1,14122 Other nations, among them JaPan, Israel,13188 Germany, Union of South Africa, Australia, Netherlands, France, Yugoslavia, Russia, and groups such as the Organization for European Economic Cooperation (OEEC)' are also diligent. The objective is low cost water, which means that both technology and economics have prominent roles in saline water conversion processes. TECHNOLOGY: SALINE WATER CONVERSION A number of reviews of methods have been made, principally by staff members of the Office of Saline Water (U.S. Dept. of Interior). Jenkins,31'32 Gillam,34p

Jan 1, 1962

By M. Schmellenkamp

By comparing two longwall operations, one begun in 1956 and the other in 1960, the author is able to demonstrate the increases in production and performance made possible by longwall mining. These achievements have been brought about by continuous development of longwall mining equipment and associated roof supports. Because of this progress, longwall mining is able to provide, under proper conditions, high production per man-shift, remarkable cost savings, dependable roof control, safe working conditions and truly continuous production. It may seem odd that the title of this paper is not simply "Longwall Mining" but instead "Progress in Longwall Mining." However, the word "Progress" definitely has its place in longwall mining. If it had not been for progress in the development of longwall mining equipment and roof supports, the longwall mining method would not be able to compete in production and performance with modem coal mining machines. The longwall mining method was practiced at the beginning of the century and there were several successful operations in coal fields in Illinois. In those early days of longwall mining, the coal was undercut by hand 2 to 2.5 ft at the bottom of the seam and packwalls were built in the gob to support the roof. The roof eventually subsided and the weight of the subsiding roof was used to ride the face and break the undercut coal. Utilizing natural weight to soften the coal face is still practiced in modern longwall mining; however, the packwalling method has been replaced by the caving method and the roof is now supported by yielding steel roof supports and forepoling steel headers. The purpose of these yielding-type roof supports is to provide a safe working area for the crew along the entire longwall face, to permit continuous mechanical mining across the prop free face, and to provide a strong resistance for the roof by forming an even breaking line at the gob for the roof to cave. Roof supports and associated forepoling headers should be kept as close as possible to the face in order to prevent a caving between face and supports, especially under friable roof. This means that the coal should be extracted in small slices, allowing only a narrow roof area to be exposed and unsupported. The coal planer with its relatively high cutting velocity of 75 ft per min provides such an extraction of coal and has proved its high performance under difficult mining conditions. Since 1951, several longwall faces in southem West Virginia and Pennsylvania which have been equipped with the coal planer and friction-type manual roof supports have been successfully operated. Compared to today's longwall mining, these longwall faces required such a large crew, primarily to handle the roof supports, that the actual high production per shift was charged with too high a labor cost, thereby decreasing the tons per man. Yet, even then the longwall faces outperformed the conventional mining system under the same conditions. In order to demonstrate the progress that has been made in the development of longwall mining, a comparison will be made between a longwall face in Arkansas which was installed in 1956 and a modemized longwall face started in 1960 in southern West Virginia. LONGWALL MINING IN 1956 The 320-ft longwall face was developed in a 32-in. thick coal seam near Greenwood, Ark. The method of mining the 320-ft coal block was the advancing system in which three entries on either side of the face were driven ahead of the advancing longwall face. The face was equipped with a coal planer and a Panzer conveyor; timbering was done with wooden timbers and cribs. The roof supports were set without any pattern. The crew to operate the planer and to handle the roof supports (timbers and cribs) consisted of 15 men per shift. During a period of approximately eight monthsof single shift operating time, the average tonnage produced in this relatively low seam amounted to about 263 tons of clean coal per shift. To show the development in the coal plow from then until now, it should be pointed out that the standard plow was used in this operation. The plow was equipped with rigid bottom bits which could not be adjusted if the plow started to climb, thereby leaving bottom coal to be recovered by pick hammers end causing delays in production. The height of the plow

Jan 1, 1963

By Geo. W. Bain

PRODUCERS of building stone have had to seek new and attractive uses for their output to supplement the diminished orders for standard products. Lunar is the direct result of the need of new outlets for marble and is. probably the most ingenious and attractive type to reach the market in a quarter of a century. It is a highly translucent stone which retains the same glistening sparkle in transmitted light that marble exhibits by incident rays. This sparkle sets it apart entirely from translucencies made of glass or even onyx, alabaster, and the distinctive exceedingly fine textured calcite marbles produced in Alabama and quarried formerly in northern Vermont and Quebec.

Jan 1, 1936

By FREDERICK LAISY

A NUMBER of new plants for the treatment of copper ores were completed or under construction during the year. Among these may be mentioned the plants of the International Nickel Co., those of the Hudson Bay Mining and Smelting Co. and of the Roan Antelope Copper Co. Three copper re- fineries have been constructed, one at El Paso, Tex., and the other two in Canada. Two more are projected, one in France and one in England. The International Nickel Co.'s plant consists of an 8000-ton concentrator and a smelting plant containing thirty 10-hearth Herreshoff roasting furnaces, five reverberatory furnaces, and eight Smith-Pierce converter5 . The smelting plant is estimated to have a capacity of 5000 tons of ore or concentrate per day. The roasters are superimposed on the reverbratory furnace plant. As a consequence of this arrangement, the furnace building is unusually high. being 183 ft. from yard level to highest roof elevation.

Jan 1, 1931

By C. L. Prokop

A laboratory investigation has been made of the effects of mud hydraulics upon the formation and erosion of mud filter cakes. The tests were conducted to simulate drilling conditions as nearly as possible. The formation of mud filter cake in a drilling well does not proceed at a uniform and unbroken rate. Instead, the rate of cake accumulation depends upon whether or not the mud is being circulated. If the mud column is quiescent, filter cake formation is a smooth function of the filtration characteristics of the system. If the mud is being circulated filter cake formation depends not only upon the filtration characteristics of the mud but also upon the erosive action of the flowing mud column Filter cakes formed during continuous mud circulation were observed to reach an equilibrium thickness after several hours' circulation. Mud circulation was maintained at a constant volumetric rate throughout each experiment. The fluid velocity at equilibrium cake thickness was dependent upon the thickness of the filter cake. Muds having exceptionally high water loss deposited thick filter cakes in spite of very high eroding velocities. The muds having good filtration characteristics deposited thin filter cakes at equilibrium circulating velocities well within tile range of those in a drilling well. It was observed that filter cakes deposited during stagnant filtration were quite difficult to erode by mud circulation. The - rate of crosion computed from the rate of filtrate accumulation after equilibrium cake thickness had been reached was in reasonable agreement with the rate of erosion obtained by direct observation. Continuous mud circulation usually caused the permeability of the filter cake to decrease with time. INTRODUCTION Many of the difficulties encountered during tile drilling of a well have been attributed to the loss of water from the mud and the attendant deposition of solids upon the walls of the hole. Past experience has shown that a reduction of the filtration rate of the drilling fluid eliminates or greatly reduces these difficulties. Definite filtration requirements, however, are hard to establish for a given set of conditions. This is due. in part, to the fact that the usual filtration test performed upon mud doe? not simulate well conditions as closely as desirable. The filtration characteristics of a mud are customarily determined by means of the standard low-pressure API wall-building tester.' In this instrument a filter cake is deposited upon a horizontal bed under a pressure differential of 100 psi. The rnud is quiescent during the filtration period. In actual practice. mud filtration occurs within a well under quite different conditions. One of the major differences is that mud flows upward across the filter bed as the filter cake forms. This undoubtedly produces a change in the filter cake which cannot be reflected in the results of the API test. The laboratory work described in this paper had as its primary objective a better understanding of the influence of mud circulation upon the thickness and ,characteristics of the filter cakes deposited under conditions similar to those existing in a drilling well. ANALYSIS OF PROBLEM Once a permeable formation is penetrated by the bit, filtrate from the mud flows into the formation. 'he mud solids plaster against the walls of the hole, forming a filter cake. If the mud column is stagnant, that is, if it is not being circulated. the filter cake will increase in thickness until the hole is filled. Prior to the time that the hole is filled, the thickness of filter cake existing at any given time will be a function of the filtration characteristics of the mud, the temperature, and the pressure differential. The effects of these variables have been investigated in the past for both flat bed filtration2'3 and for radial filtration.' When the mud is circulated in a hole in which a filter cake i. being deposited. some of the solids that would ordinarily deposit in the filter cake will be carried away by the eroding action of the mud. This will limit. filter cake thickness. Some work has been done to determine the effect of flow upon the filtration rate in a circulating mud system' but little work has been done upon the factors which determine the filter cake thickness existing in a circulating system. On first sight it would appear that the major factors controlling filter cake formation in a circulating system should be: 1. The rate of deposition of solids from the mud. 2. The erosive force that the flowing mud exerts upon the filter cake. 'A. The erodabilitv of the filter cake. 4. Any change in filter cake characteristics attributable to the scouring action of the mud. The rate at which solids are deposited from the mud will be controlled to a large degree by the filtration characteristics of the mud, the pressure differential. the temperature under

Jan 1, 1952