Search Documents

By A. E. Perkins

fractured ingot will show a complete diagonal structure. If the temperature is lowered, the equi-axed zone is larger and the pine tree growth is less. A small ingot, though, is prone to this columnar structure, even though the casting temperature is kept down. The speed of cooling after solidification is slower in the hollow ingot than in the solid, therefore the granulation, which takes place after the crystals have formed from the liquid metal, is apt to produce larger grains than in the solid ingot. This is not a detriment. The original crystal size is of much more importance. The size of the grains due to this granulation constantly varies in response to mechanical work and subsequent heat treatment. Surface weakness, as shown by seaming and checking on the exterior when working or by cracking in hardening, is in some measure the result of the surface stresses of the ingot when cast. The temperature of the ingot mold or speed of freezing of the exterior of the ingot is of great importance and much seamy and cracked steel is caused by a too quickly cooled skin. Ingots that are turned or milled all over will not seam very much in working, in fact they are practically free from seams, whereas an ingot rolled without a preliminary machining operation is full of seams and cracks, some long and some short. It has been said that these short seams and cracks in the surface of the bar are the result of elongated depressions in the surface of the ingot and that if an ingot is cast very smooth it should give fewer surface defects. This is partly true, but an ingot cast very hot and having a very smooth skin will crack and seam very badly in the mill, as will the surface of an ingot poured very cold, which is very crinkly, because of the low temperature of the metal. The cause of the cracks and seams in one is not the cause of the cracks and seams in the other. The tube method of hollow drill steel manufacture is superior to the older method because of: (1) Greater freedom from external and internal straining; (2) the inherent small crystal size; (3) absence of harmful segregation, resulting in weakness of wall of hole. (4) less liability for steel to crack in inside of hole during forging or hardening; (5) toughening effect, arising from mild steel wall of hole limiting the intense hardening on quenching. Breakage and Heat Treatment or Rock-drill Steel By A. E. Perkins, Pittsburgh, Pa. Actual figures showing the superiority of one section or another are difficult to obtain. In a given size of steel, however, the cruciform sec -tion shows the most breakage; it is inherently a weak section. It contains less steel per foot than any other standard section of the same size and when rolled the wings tend to cool off setting up cooling stresses.

Jan 1, 1922

By R. T. DeHoff

In any structural transfortnation which is driven by surface tension, the geometric variable of fimdamental importance is the local value of the mean surface curvatuve. Acting through the suvface free energy, this quantity determines the magtnitude of both the pressure and the chemical potential that develops in the neighborhood of an arbitrarily curved surface. A metallographic method which would permit the quaniitatiue estinzation of this propevty is of fundarnerztal irztevest to studies of such processes. In the present paper, it is shoun that the average value of the mean surface curvature in a structuve can be estimated from two simple counting measuretnents made upon a vepresentative metallograpIzic section. No simplifyirlg geonzetric assurmptions are necessary to this deviuation. It is further shoum that the result may be applied to parts of interfaces, e.g., interparticle welds in sintering, or the edge of growing platelets in a phase transformation, without loss of validity. In virtually every metallurgical process in which an interface is important, the local value of the mean surface curvature is the key structural property. This is true because the mean curvature determines the chemical potential of material adjacent to the surface, as well as the state of stress of that material. The theoretical description of such broadly different processes as sintering,1,2 grain growth,3 particle redistrib~tion4,5 and growth of Widmanstatten platelets8 all have as a central geometric variable the "local value of the mean surface curvature". The tools of quantitative metallography currently available permit the statistically precise estimation of the total or extensive geometric properties of a structure: the volume fraction of any distinguishable part:-' the total extent of any observable interface,10,11 and the total length of some three-dimensional lineal feature:' and, if some simplifying assumptions about particle shape are allowed, the total number of particles.'2"3 The size of particles in a structure, specified by a distribution or a mean value, can only be estimated if the particles are all the same shape, and if this shape is relatively simple.14-16 The relationships involved in converting measurements made upon a metallographic section to properties of the three dimensional structure of which the section is a sample are now well-established, and their utility amply demonstrated. In the present paper, another fundamental relationship is added to the tools of quantitative metallography. This relationship is fundamental in the sense that its validity depends only upon the observation of an appropriately representative sample of the structure, and not upon the geometric nature of the structure itself. It involves a new sampling procedure, devised by Rhines, called the "area tangent count". It will first be shown that the "area tangent count" is simply related to the average value of the curvature of particle outline in the two-dimensional section upon which the count is performed. The average curvature of such a section will then be shown to be proportional to the average value of the Mean surface curVature of the structure of which the section is a sample. The final result of the development is thus a relationship which permits the evaluation of the average value of the mean surface curvature from relatively simple counting measurements made upon a representative metallographic section. The result is quite independent of the geometric or even topological nature of the interface being studied. QUANTITATNE EVALUATION OF AVERAGE CURVATURE IN TWO DIMENSIONS The Area Tangent Count. Consider a two-dimen-sional structure composed of two different kinds of distinguishable areas (phases), Fig. l(a). If the system is composed of more than two "phases", it is possible to focus attention upon one phase, and consider the remaining structure as the other phase. The reference phase is separated from the rest of the structure by a set of linear boundaries, of arbitrary shapes and sizes. These boundaries may be totally smooth and continuous, or piecewise smooth and continuous. An element of such a boundary, dA, is shown in Fig. l(b). One may define the "angle subtended" by this arbitrarily curved element of arc, dO, as the angle between the normals erected at its ends, Fig. l(c). Now consider the following experiment. Let a line be swept across this two-dimensional structure, and let the number of tangents that this line forms with elements of arc in the structure be counted. This procedure constitutes the Rhines Area Tangent Count. Suppose that this experiment were repeated a large number of times, with the direction of traverse of the sweeping lines distributed uniformly over the semicircle of orientation.' Those test lines which ap- proach from orientations which lie in the range O to O + dO form a tangent with dA; those outside this range do not, see Fig. l(c). Since the lines are presumed to be uniformly distributed in direction of traverse, the fraction of test lines which form a tangent with dA is the fraction of the circumference of a semicircle which is contained in the orientation range, dO; i.e., vdO/nr or dB/n. If the number of test lines is N, the number forming tangents with dA is N(d0/n). Since each test line sweeps the entire area of the sample, the total area traversed by all N test lines is NL2. The number of tangents formed with dA, per unit area of structure sampled, is therefore

Jan 1, 1968

By AIME AIME

HOWARD H. PRESTON, professor of economics and business at the University of Washington, presented a paper before the North Pacific Section, A.I.M.E., on Jan. 23, on the "Economic Aspects of Gold and Silver." He carefully reviewed recent governmental actions that have affected those metals and gave an interpretation of their effects. A brief excerpt from his address; follows: Including the proclamation of March 6, 1933, the principal steps of the present Administration which have carried the United States off the gold standard and led up to the present program have been: (1) The Presidential proclamation of March 6 controlling gold. (2) The monetary sections of the Emergency Banking Act of March 9. (3) Mobilization of gold under Executive orders issued March 10 and April 5. (4) The gold embargo by Executive order, April 20. (5) The controlled inflation bill, May 12. (6) The joint resolution abrogating the gold clauses, June 5. (7) The Executive orders on newly mined gold, Aug. 28. (8) The President's radio address of Oct. 22 and the R.F.C. gold-buying program. (9) New anti-hoarding order calling in small holdings of gold, Dec. 28, 1933 and Jan. 15, 1934. (10) Nationalization and revaluation of gold' (Message to Congress, Jan. 15).

Jan 1, 1934

By M. T. Erickson, C. A. Rowland

Ball mills 5.5 m (18 ft) in diameter and larger tend to use energy delivered to the mill less efficiently than smaller diameter mills, particularly when the large mills carry 40% by volume ball charges. This paper will explore factors used in scaling up ball mills, showing where the advantages of one factor can possibly be negated by another factor. The paper will propose possible operating limits and areas for further study to establish selection and design limits.

Jan 1, 1985

By Carrol A. Quam

DURING the first years of operation of the titanium and iron mine of the National Lead Co. at Tahawus, New York, efforts to increase production were hampered by the increased load put on the facilities for sharpening churn-drill bits. The ore and rock are extremely hard and abrasive and it was necessary to sharpen and harden a large number of bits per day to keep the churn drills supplied. Efforts to increase the capacity of the bit shop by a two-shift operation were not wholly successful in that it was hard to train men to do a satisfactory job of sharpening and tempering the bits. The number of bits that were improperly tempered increased, thus boosting the daily requirements for bits at the drills and increasing the load on the bit-sharpening facilities.

Jan 1, 1949

By C. F. Weinaug, R. W. Farley, J. F. Wolfe

A rapid, accurate method for predicting the dew points of gas condensate systems and their subsequent normal and retrograde phase behavior with pressure decline has been developed. The method predicts dewpoint pressure, volume percent liquid, condensate content of produced gas, and the liquid and gas compositions at pressures below the dewpoint pressure. Use of a modified form of the BWR equation of state, which was established by regression calculations on experimental data from several gas condensates, provides depletion behavior predictions that are significantly improved over predictions using K-values based on convergence pressures and Standing's correlation for density. INTRODUCTION Prediction of complex hydrocarbon-mixture thermodynamics is fundamental to reservoir and gas process engineering. In particular, accurate descriptions of phase behavior are needed to plan production operations for gas-condensate reservoirs. Although analysis of reservoir behavior during producing and cycling operations can be made for simple reservoir models, extensions of these studies to more complex reservoir systems are still difficult, both with regard to numerical techniques and the phase behavior of the fluids. This report presents a mathematical method for handling the complex phase relationships encountered in retrograde condensates; it represents an advance in reservoir behavior technology in that it will aid the development of closed-form mathematical representations of total production systems. A typical phase diagram for a complex hydrocarbon mixture is shown in Fig. 1. When the reservoir temperature T, is higher than the critical temperature Tc, and lower than the critical-condensation temperature Tct' the mixture is a gas condensate. Decreasing the pressure on a condensate while maintaining nearly constant temperature will result in two phases forming at the dew point. Further decrease in pressure will cause additional liquids to be formed. This phenomenon is called retrograde condensation. As pressure continues to decrease, normal phase behavior regions are encountered (liquid vaporizes as the pressure decreases) until the low-pressure dew point is encountered. When a gas-condensate reservoir is produced, gas is withdrawn and the volume of fluids in the reservoir remains nearly constant as the pressure declines. Heavier components tend to accumulate in the liquid phase as a result of retrograde condensation, while lighter components tend to concentrate in the vapor phase. Thus, as the gas is produced the composition of the gas and the condensate

Jan 1, 1970

By F. W. Jessen, James N. Howell

INTRODUCTION The determination of cloud points has to date been limited to rather transparent oils, visual observation of the formation of a solid phase being the criterion for the standard ASTM D 97-47 method. The need for a quiclc and simple method for determining cloud points under dynamic conditions for opaque crude oils became necessary in a study of fundamental aspects of paraffin deposition from crude oils. PREVIOUS WORK The determination of cloud points in opaque oils by viscosity temperature curves is fairly new, Young' described a method employing the capillary tube principle. No information exists relative to the determination of cloud points of crude or refined oils under dynamic conditions. Shock' noticed that deposition of paraffin from crude oils took place at temperatures at or below the temperature at which a sharp inflection point occurred in the viscosity-temperature curve. This observation indicates a possible correlation between this temperature and the cloud point of the crude oil. Reistle and Vietti1 have reported that when crude oils containing small amounts of asphaltic materials were heated to temperatures sufficiently high to solubilize these materials and immediately cooled the pour point of the crude oil was lowered as much as 70°F. Sachanen\ asribes this effect to the action of colloidal asphaltenes in preventing the formation of the crystalline structure necessary to maintain the oil in a rigid state. At high temperatures, asphaltenes are peptized, and the paraffin crystals formed at these temperatures adsorb the colloidal asphaltenes on their surface thereby hindering further growth of the crystals. Reistle" found, however, that such heating and cooling of crude oils had no effect upon the cloud points. This latter work dealt with a crude oil of fixed composition, and the question immediately arises as to the effect of varying the concentration of asphaltic materials on the cloud point. APPARATUS AND PROCEDURE All viscosity measurements were made with a Bendix Ultra-Viscoson. The Bendix Ultra-Viscoson, which consists of a vibrating probe and an electronic computer. measures viscosity by exciting a thin alloy steel blade on the end of a probe by short electrical pulses in damped oscillation at 28 kilocycles. The blade vibrates longitudinally with an amplilude of less than 55 micron or 20 millionths of an inch. Energy to protlucc this excitation is generated in he computer and transferred to the probe through the connecting cable. The oscillating blade is magnetostric-tive, i.e., it is capable of transforming electrical energy to mechanical energy in the ultrasonic range. Ultrasonic waves are produced in the material surrounding the blade by the oscillating motion of the blade causing layers of the material to slip back and forth over one another at a known frequency. The electronic computer calculates the energy required to produce the sliding motion which is in turn proportional to the viscosity of the material. Actual values of viscosity times density (centi-poise X grams/cc) are indicated on the computer and a continuous D-C signal is provided which is fed into a type 153 Electronic Recorder (manufactured by Brown Instruments Div. of Minneapolis-Honeywell Regulator Co.) The liquid sample container was fabricated from a Lucite cylinder and jacketed by a Luicite water bath. Early experiments using glass and steel sample containers were not satisfactory. since the Ultra-Viscoson was apparently affected by the alterzltion of the magnetic fields surrounding the probe by stresses set LIP in the glass and steel as it cooled. The procedure for determining viscosity-temperature curves was relatively simple. The temperature ot the sample was raised sufficiently high to solubilize all paraffin and asphalts present. After heating, the oil sample was immediately transferred

Jan 1, 1957

By A. J. Teplitz, R. J. Goodwin

A new type water shut-off for use in air drilling has been developed. The method has been 99 to 100 per rent effective in several different formations of inter-ranular-type porosity. Since costs for materials, time and equipment used are relatively small, the process should extend economies of air drilling to many new areas. The treatment involves a new technique for forming a water-inroluble precipitate within the pores of a rock. Advantage it taken of the difference in mobility of a liquid and a gas in porous media to achieve the greatest volume of precipitate in a given pore. Reactants selected for the laboratory (2nd field tests were aluminum sulfate solution and gaseous ammonia. This process has been tested in both intergranular and fractured-type porosities. It has consistently shut-of between 99 and 100 per cent of the water flowing from formations having intergranular-type porosity and perrlreuhilities ranging from a few millidarcise to over a darcy The treatment is not particularly suitable for shutting-off water from fractured formations although plugging of the order of 50 per cent or greater has been achieved in all such applications. Among advantages of the treatment are: (I) no reaction waiting rime after a relatively short placement time, (2) a low mate-rials cost of about $3/f1 of hole treated, (3) use of common service-type equipment for treatment, and (4) no unusual requirements for mixing and placement. INTRODUCTION In rotary drilling with air or gas it has been possible to increase bit life by tenfold and more than double rate of penetration over corresponding performance when drilling with mud. These factors have amounted to as much as 22 per cent savings on total cost of drilling a well. However, these advantages are rapidly lost when water is encountered in an air- or gas-drilled well because water interferes with the removal of cuttings from the hole and also gives rise to other difficulties. In attempting to combat water troubles, operators have commonly resorted to such measures as mist drilling, treatment with cement or chemicals, converting to conventional mud drilling, or setting casing. In many cases these measures have either been costly or ineffective. In an effort to overcome this problem, studies were undertaken to develop an effective and economical water shut-off technique for use in formations possessing inter-granular-type porosity. Extensive laboratory experimentation finally led to a unique method for producing a water-insoluble precipitate within the pores of a sandstone. The unique part of the treatment is use of a liquid and a gas to form the precipitate, and in this case the reactants used were aluminum sulfate solution and gaseous ammonia. The reaction between these two materials is shown in the following equation. Al2 (SO1)3 - 18 H20 6NH2? saturated Water- Solution Cat 2A1(OH)3 . n H20 3(NH4)2SO • n H20 Solid Solid That is, a solid precipitate consisting of aluminum hydroxide and ammonium sulfate is formed when ammonia reacts with aqueous aluminum sulfate. The aluminum hydroxide is insoluble in water and the ammonium sulfate, though soluble, can only be removed from the formation pores by diffusion—an extremely slow process. Although the precipitate formed by the reaction is not particularly firm, great strength is not needed for a precipitate to bridge and plug intergran-ular-type porosity. A flow path in such a system is extremely tortuous and involves a great variety of pore

GEORGE K. BURGESS,* Washington, D. C. (written discussiont).-Professor Sauveur refers to the International Aircraft Standards Board in terns that would indicate his non-familiarity with, the organization and the working of this Board which, of course, is excusable on account of Professor Sauveur's absence in Europe at the time. He implies .that the work of this Board was entirely dominated by American interests, whereas diametrically the opposite was the case. The Board, was organized for the purpose of facilitating purchase in the United States, on the basis of common specifications, by the Allied air, services in the United States, and the Board performed a very valuable service in unify-ing the specifications of Italy, Great Britain, France, Canada, and the United States for such purposes. The proceedings of the Board were car-ried out on the basis of unanimous agreement of the representatives of the five countries and all the members from each of the countries were technical specialists or, had the advice of technical assistants. It would be difficult to find an instance of greater unity of purpose, readiness to' compromise, and efficient production than was shown by this Board, which produced seventy-eight specifications, in the preparation of which representative American manufacturers appeared before the Board.

Jan 12, 1919

By M. G. Cheney

Careful estimates indicate that during 1942 new discoveries and extensions in West Central Texas added oil reserves slightly in excess of the eight million barrels produced. Drilling activity fell 40 per cent below 1941 and 82 per cent below the normal drilling activity of the late 1920's. Total production for the district continued its downward trend, now being less than % of the 42.7 million barrels peak in 1921. Rapid revival of activity is not probable under existing conditions, as costs of discovery, development and operations on the average probably now exceed current market price for the oil, the latter having remained constant since the spring of I941. Costs have advanced materially since the third quarter of 1941, when reports to the Tariff Commission indicated a margin of profit of 13.3 per barrel. Physical as well as economic conditions are holding back the amount of drilling in this district. The lenticular sands are not suited to 40-acre spacing regulations. There is no surplus of experienced oil-field labor. To reduce costs, much second-hand material is used for all except the deeper wells.. Price controls have retarded movement of used equipment by prescribing maximum prices that arc too low for the better grade materizl, thus making , owners reluctant to sell. On the other hand, buyers are unwilling to pay ceiling prices asked by sellers for poor material. Seventeen new oil fields and five new gas fields were found during 1942. Extensions and deeper 'drilling brought favorable results in eight older fields. The most significant new developments appear to have been in Coleman, Jones, Shackelford and Taylor Counties. A 5800-ft. completion in Wise County brought this county into the producing column for the first time. None of these new discoveries can he rated above one million barrel reserve on the basis of present development. Probably the most important development was discovery of a deeper pay (Gunsight lime) in the Wimberly field of Jones County, which shows promise of producing over an area of about 1000 acres. Jones and Shackelford Counties still lead the district in total annual production. Discovery of the Reddin pool, north central Taylor County, is credited to geochemical methods, making one success out of five or more wildcats based on such methods. Geophysical surveying increased decidedly during 1942 and returns from these studies are expected during coming years. Most of the wildcatting in the district is still based on surface and subsurface geological structural mapping, study of log data as to distribution of prospective producing reservoirs, and drilling in proximity to previous showings of oil and gas. Geological debate continues as to the proper correlation of the 100 to 300 ft. of gray lime that has produced more than 100 million barrels in the Parks, Brecken-ridge, Curry, Eliasville, Ibex, Pioneer and other important fields of this district. Fossils indicate that this limestone is younger than the Atoka beds of Oklahoma. On a structural basis most geologists include this formation with the Bend but a number of paleontologists believe it is more properly classified with the Strawn.

Jan 1, 1943

By M. G. Cheney

Careful estimates indicate that during 1942 new discoveries and extensions in West Central Texas added oil reserves slightly in excess of the eight million barrels produced. Drilling activity fell 40 per cent below 1941 and 82 per cent below the normal drilling activity of the late 1920's. Total production for the district continued its downward trend, now being less than % of the 42.7 million barrels peak in 1921. Rapid revival of activity is not probable under existing conditions, as costs of discovery, development and operations on the average probably now exceed current market price for the oil, the latter having remained constant since the spring of I941. Costs have advanced materially since the third quarter of 1941, when reports to the Tariff Commission indicated a margin of profit of 13.3 per barrel. Physical as well as economic conditions are holding back the amount of drilling in this district. The lenticular sands are not suited to 40-acre spacing regulations. There is no surplus of experienced oil-field labor. To reduce costs, much second-hand material is used for all except the deeper wells.. Price controls have retarded movement of used equipment by prescribing maximum prices that arc too low for the better grade materizl, thus making , owners reluctant to sell. On the other hand, buyers are unwilling to pay ceiling prices asked by sellers for poor material. Seventeen new oil fields and five new gas fields were found during 1942. Extensions and deeper 'drilling brought favorable results in eight older fields. The most significant new developments appear to have been in Coleman, Jones, Shackelford and Taylor Counties. A 5800-ft. completion in Wise County brought this county into the producing column for the first time. None of these new discoveries can he rated above one million barrel reserve on the basis of present development. Probably the most important development was discovery of a deeper pay (Gunsight lime) in the Wimberly field of Jones County, which shows promise of producing over an area of about 1000 acres. Jones and Shackelford Counties still lead the district in total annual production. Discovery of the Reddin pool, north central Taylor County, is credited to geochemical methods, making one success out of five or more wildcats based on such methods. Geophysical surveying increased decidedly during 1942 and returns from these studies are expected during coming years. Most of the wildcatting in the district is still based on surface and subsurface geological structural mapping, study of log data as to distribution of prospective producing reservoirs, and drilling in proximity to previous showings of oil and gas. Geological debate continues as to the proper correlation of the 100 to 300 ft. of gray lime that has produced more than 100 million barrels in the Parks, Brecken-ridge, Curry, Eliasville, Ibex, Pioneer and other important fields of this district. Fossils indicate that this limestone is younger than the Atoka beds of Oklahoma. On a structural basis most geologists include this formation with the Bend but a number of paleontologists believe it is more properly classified with the Strawn.

Jan 1, 1943

By David B. Reger

The substantial expansion of previously discovered gas pools was the principal feature of petroleum activity in West Virginia during 1940. At least one new gas pool was discovered and various other successful wildcat completions may prove to be gas-pool openers. Some slight extensions of oil pools were also made. The new productive territory, principally gas, added by these extensions was approximately 33,800 acres. ' In general, oil activity was slight because of unfavorable crude prices. Gas activity, on the contrary, increased considerably, although the price of gas did not materially change. The account of operations, as gathered from trade journals and other reporting services, shows that 709 new wells were drilled, resulting in 102 new oil wells with I055 bbl. of daily new produc-tion; 468 new gas wells with 633>g47,000 cu. it. of daily open flow; and 139 dry holes. Also, 91 old wells were drilled to deeper sands, with 143 bbl. and 44,833,000 cu. ft. of added production. On the new wells the oil average was 10.34 bbl, per well per day; and the gas average was 1,354,000 cu. ft. per well per day. On new wells the ratio of dry holes to completions was 19.61 per cent. On deeper drilling to other sands the ratio of failures was 12.I per cent. From an exploratory standpoint, one strictly new gas pool (Lorentz) was opened in Upshur County. Little forecast of its extent or reserve can now be made. The new extensions of various other previously discovered pools, however, give assurance of a new gas reserve that will equal approximately a year of gas demand. In addition to these definite supplies two widely separated Oriskany sand (L. Dev.) wildcats in Jackson County, one of which was completed late in 1940 and the other early in 194.1, may indicate two separate pools or may greatly extend known pools. In south-ern Kanawha County, also, an old Oris-kany-sand well deepened to the White Clinton sand (Sil.) showed a volume of 733,000 cu. ft. and rock pressure of 1800 Ib., giving rather clear assurance that this deep sand, in which only slight quantities of gas had previously been found, should eventually supply much new gas. On the other hand, various deep tests to the Oriskany sand in Harrison, Putnam, Randolph and Wood Counties were totally dry or gave only small volumes of gas, The principal oil wells completed, by counties, were: Calhoun, 15; Clay, Ir; Pleasants, 14; Ritchie, 15; and Roane, 7. Production for the year was estimated by the U. S. Bureau of Mines as 3,444,000 bbl., as compared to 3,684,000 bbl. in 1939. The leading counties in gas-well completions were: Boone, 36; Braxton, 17; Cabell, 25; Calhoun, 16; Clay, 22; Gilm.er, 47; Jackson, 38; Kanatvha, 77; Lincoln, 18; Putnam, 32; IGtchie, 40; and Wayne, 31, Production for the year is estimated by me as I70,000,000,000 cu. ft. as compared to I59,226,000,000 cu. ft.* in 1939. No long pipe lines were built but various gas-line extensions and cross connections,

Jan 1, 1941

By David B. Reger

The expansion of the previously discovered gas pools and an intensified search for additional pools in the Oriskany and deeper sands were the principal petroleum activities in West Virginia during 1941. One small oil pool was discovered and another was considerably extended. One small gas pool was discovered, several isolated well discoveries were expanded into definite pools, and various recognized pools were substantially increased. The proved oil territory of the state was increased about 600 acres and the proved gas territory about 45,000 acres. The new discoveries of oil did not equal withdrawals but gas reserves added were greater than gas withdrawals. Oil activity, as in the past several years, was slight because of unfavorable crude prices. Most operators prefer to leave oil in the ground rather than to drill for it without a better return. Gas activity increased greatly because of better demand, even though the price of gas did not improve. The account of operations, as gathered from trade journals and other reporting services, shows that 838 new wells were drilled, resulting in 114 new oil wells with 2606 bbl. of daily new production; 558 new gas wells with 949,226,000 cu. ft. of daily open flow; and 166 dry holes. Also, 86 old wells were drilled to deeper sands with 9 bbl. and 56,030,000 cu. ft. of added production. On the new wells the oil average was 22.86 bbl. per well per day; and the gas average was 1,701,000 cu. ft. per well per day. On new wells the ratio of dry holes to completions was 13.61 per cent. On deeper drilling to other sands the ratio of failures was 15.12 per cent. From an exploratory standpoint one strictly new oil pool (Higginbotham Run) was opened in Kanawha County and one strictly new gas pool (Lost Run) in Taylor County. One entirely isolated wildcat gave commercial Oriskany-sand gas production and may open a pool. Various other wildcats greatly extended the boundaries of known Oriskany-sand gas pools and various others may have opened new pools in the shallow sands. On the other hand, various Oriskany tests in Harrison, Monongalia, Roane and Wood Counties were dry and all five tests to the White Clinton sand (Sil.) in Boone, Harrison, Kanawha and Wood Counties failed to find commercial production. The principal oil wells completed, by counties, were: Calhoun, 24; Clay, 7; Gilmer, 6; Hancock, 9; Kanawha, 9; Pleasants, 10; and Ritchie, 14. Production for the year was estimated by the Oil Weekly as 3,421,000 bbl., compared with U. S. Bureau of Mines final figures of 3,444,000 bbl. in 1940. The leading counties in gas-well completions were: Boone, 32; Braxton, 19; Cabell, 16; Calhoun, 46; Clay, 20; Gilmer, 37; Jackson, 94; Kanawha, 82; Lincoln, 17; Putnam, 46; Ritchie, 33; Upshur, 20; and Wayne, 33. Production for the year is estimated by the author as 210,000,000,000 cu. ft., as compared to the U. S. Bureau of Mines' final figures of 188,751,000,000 cu. ft.* in 1940.

Jan 1, 1942

By David B. Reger

The substantial expansion of previously discovered gas pools was the principal feature of petroleum activity in West Virginia during 1940. At least one new gas pool was discovered and various other successful wildcat completions may prove to be gas-pool openers. Some slight extensions of oil pools were also made. The new productive territory, principally gas, added by these extensions was approximately 33,800 acres. ' In general, oil activity was slight because of unfavorable crude prices. Gas activity, on the contrary, increased considerably, although the price of gas did not materially change. The account of operations, as gathered from trade journals and other reporting services, shows that 709 new wells were drilled, resulting in 102 new oil wells with I055 bbl. of daily new produc-tion; 468 new gas wells with 633>g47,000 cu. it. of daily open flow; and 139 dry holes. Also, 91 old wells were drilled to deeper sands, with 143 bbl. and 44,833,000 cu. ft. of added production. On the new wells the oil average was 10.34 bbl, per well per day; and the gas average was 1,354,000 cu. ft. per well per day. On new wells the ratio of dry holes to completions was 19.61 per cent. On deeper drilling to other sands the ratio of failures was 12.I per cent. From an exploratory standpoint, one strictly new gas pool (Lorentz) was opened in Upshur County. Little forecast of its extent or reserve can now be made. The new extensions of various other previously discovered pools, however, give assurance of a new gas reserve that will equal approximately a year of gas demand. In addition to these definite supplies two widely separated Oriskany sand (L. Dev.) wildcats in Jackson County, one of which was completed late in 1940 and the other early in 194.1, may indicate two separate pools or may greatly extend known pools. In south-ern Kanawha County, also, an old Oris-kany-sand well deepened to the White Clinton sand (Sil.) showed a volume of 733,000 cu. ft. and rock pressure of 1800 Ib., giving rather clear assurance that this deep sand, in which only slight quantities of gas had previously been found, should eventually supply much new gas. On the other hand, various deep tests to the Oriskany sand in Harrison, Putnam, Randolph and Wood Counties were totally dry or gave only small volumes of gas, The principal oil wells completed, by counties, were: Calhoun, 15; Clay, Ir; Pleasants, 14; Ritchie, 15; and Roane, 7. Production for the year was estimated by the U. S. Bureau of Mines as 3,444,000 bbl., as compared to 3,684,000 bbl. in 1939. The leading counties in gas-well completions were: Boone, 36; Braxton, 17; Cabell, 25; Calhoun, 16; Clay, 22; Gilm.er, 47; Jackson, 38; Kanatvha, 77; Lincoln, 18; Putnam, 32; IGtchie, 40; and Wayne, 31, Production for the year is estimated by me as I70,000,000,000 cu. ft. as compared to I59,226,000,000 cu. ft.* in 1939. No long pipe lines were built but various gas-line extensions and cross connections,

Jan 1, 1941

By David B. Reger

The expansion of the previously discovered gas pools and an intensified search for additional pools in the Oriskany and deeper sands were the principal petroleum activities in West Virginia during 1941. One small oil pool was discovered and another was considerably extended. One small gas pool was discovered, several isolated well discoveries were expanded into definite pools, and various recognized pools were substantially increased. The proved oil territory of the state was increased about 600 acres and the proved gas territory about 45,000 acres. The new discoveries of oil did not equal withdrawals but gas reserves added were greater than gas withdrawals. Oil activity, as in the past several years, was slight because of unfavorable crude prices. Most operators prefer to leave oil in the ground rather than to drill for it without a better return. Gas activity increased greatly because of better demand, even though the price of gas did not improve. The account of operations, as gathered from trade journals and other reporting services, shows that 838 new wells were drilled, resulting in 114 new oil wells with 2606 bbl. of daily new production; 558 new gas wells with 949,226,000 cu. ft. of daily open flow; and 166 dry holes. Also, 86 old wells were drilled to deeper sands with 9 bbl. and 56,030,000 cu. ft. of added production. On the new wells the oil average was 22.86 bbl. per well per day; and the gas average was 1,701,000 cu. ft. per well per day. On new wells the ratio of dry holes to completions was 13.61 per cent. On deeper drilling to other sands the ratio of failures was 15.12 per cent. From an exploratory standpoint one strictly new oil pool (Higginbotham Run) was opened in Kanawha County and one strictly new gas pool (Lost Run) in Taylor County. One entirely isolated wildcat gave commercial Oriskany-sand gas production and may open a pool. Various other wildcats greatly extended the boundaries of known Oriskany-sand gas pools and various others may have opened new pools in the shallow sands. On the other hand, various Oriskany tests in Harrison, Monongalia, Roane and Wood Counties were dry and all five tests to the White Clinton sand (Sil.) in Boone, Harrison, Kanawha and Wood Counties failed to find commercial production. The principal oil wells completed, by counties, were: Calhoun, 24; Clay, 7; Gilmer, 6; Hancock, 9; Kanawha, 9; Pleasants, 10; and Ritchie, 14. Production for the year was estimated by the Oil Weekly as 3,421,000 bbl., compared with U. S. Bureau of Mines final figures of 3,444,000 bbl. in 1940. The leading counties in gas-well completions were: Boone, 32; Braxton, 19; Cabell, 16; Calhoun, 46; Clay, 20; Gilmer, 37; Jackson, 94; Kanawha, 82; Lincoln, 17; Putnam, 46; Ritchie, 33; Upshur, 20; and Wayne, 33. Production for the year is estimated by the author as 210,000,000,000 cu. ft., as compared to the U. S. Bureau of Mines' final figures of 188,751,000,000 cu. ft.* in 1940.

Jan 1, 1942

By Robert K. Waits

The resistivity, temperature coefficient of resistance, stability at 200°C, and structure of annealed Si-Cr films have been studied as a function of film cowposition. Colorimetric analyses of the films indicated 20 to 60 wt pct Cr over the resistivity range of 1 to 10-4 ohm-cm. Resistors were delinealed by photolithographic etching, contacted with aluminum, and mounted in TO-5 packages. The average temperature coefjicient of resistance, a, between 50" and 150°C is related empirically to the film resistivity, p, by a (ppm per °C) = -2900 - 1140 log p (ohm-cm). Near a resistivity of 3.5 x 10-3 ohm-ctn (30 at. pct Cr) , the temperature coefficient changes from positive to negative. The temperature at which the resistance maximum occurs increases with decreasing resistivity. The conduction mechanism between —196" and +360 C appears to have two components—an activated conduction dominating a1 lord chromium content and higher temperatures and a linearly temperature-dependent conduction dominating at high chromium content and low temperatures. Electron diffraction patterns showed the films to consist of Cr3Si and amorphous silicon. Resistors thicker than 150A typically drifted less than 0.6 pct after 5000 hr stor-age at 200°C. Resistors as thin as approxinzately 80°A that had a silicon overlayer showed similar stability. Such films had sheet resistivities of 10 kilohm per square and temperature coefficients near —600 ppm per "c. THIN-FILM resistors having sheet resistivities greater than 1 kilohm per square are required in many integrated circuit applications. A process for producing such resistors should be compatible with present circuit fabrication and packaging, including exposure to maximum temperatures of 300° to 570°C during contact alloying, die-attach, and ceramic package sealing. In addition, the resistors should have a low temperature coefficient of resistance and change less than 1 pct during storage at temperatures up to 200°C for 1000 hr or longer. Reports of work beginning in 1949 at Battelle Memorial Institute indicated that, among other materials, the silicides of chromium, Cr-Co, molybdenum, tantalum, and tungsten were worthy of further study as high-stability resistive films. Later work on Si-Cr films vacuum-deposited by flash evaporation from a tungsten boat1 led to the conclusion that Si-Cr had "excellent properties for development into high- stability ... resistive elements". More recently, Si-Cr films have been vacuum-deposited from a tantalum boat,2 from a BeO-coated tantalum boat,3 by flash evaporation from an electron-beam-heated tungsten Source,4 and by triode sputtering.5 This paper describes a study of Si-Cr films vacuum-deposited by electron-beam heating of Si-Cr alloys. Resistivity, temperature coefficient of resistance, stability at 200°C, and structure were studied as a function of film composition. EXPERIMENTAL PROCEDURE Film Deposition. Si-Cr sources were prepared by vacuum-melting pressed pellets of mixtures of powdered chromium (99.9 pct, -100 mesh, Lunex Co., Pleasant Valley, Iowa) and silicon (99.99 pct, -325 mesh, United Mineral and Chemical Co., New York). A permanent-magnet focused electron-beam gun having a water-cooled copper crucible was used to heat the pellet until complete melting occurred. The mixture was then kept molten for an additional 5 min. The alloy thus formed was used as the source material for Si-Cr film depositions using the same electron-beam gun. Pieces of semiconductor-grade silicon ingots were used as sources for silicon depositions. The films were deposited within a standard vacuum evaporator having an 18-in.-diam Pyrex bell jar, a liquid-nitrogen-cooled trap, and a Consolidated Vacuum Corp. 6-in. diffusion pump containing Dow Corning DC-705 pump fluid. The substrates were thermally oxidized* silicon wafers 2 to 2.5 cm in diam. The

Jan 1, 1969

By R. D. Taylor, Jim Douglas Jr., H. H. Rachford Jr., P. M. Dyke

A major obstacle to the use of wetting agents in .secondary recovery by water flooding is the adsorption of the agents on the sand. As a result of adsorption, the surfactant always lags behind the floodwater front. Consideration of the chromatographic theory of adsorption indicates that the detergents will not lag as much if used in very high concentrations. An investigation was made of the possibility of using high concentrations economically by flowing slugs of wetting agents followed by normal flood water. The experiments consisted of adsorption studies on Alundum powder and Berea sandstone. Flow rests on a 12-in. Alundum core and 22-in. Berea core were used to determine rate of detergent movement. The results of the flow experiments indicate that the relative rate of surfactant advance is, indeed, sensitive to the concentration of the agent. A 10 per cent slug moved with a rate that war 78 to 95 per cent as fast as the rate of advance of the flood water. By contrast, one with 25 ppm (the number of parts of commercial detergent in a million parts of water on a weight basis) concentration moved less than one-fourth as fast as the flood water, and calculations indicate that in very long porous systems the rate of movement of the lower concentrations will be a small fraction of the rate of advance of the flood front. The results. of the adsorption studies were utilized to calculate the rate of advance of the detergent when only the initial concentration was known. The calculated rates showed substantial agreement with the experimental flow tests in the high concentration ranges. The adsorption results were also used to estimate the cost of the materials for a slug-type surfactant flood in the field. In addition to the faster rates of movement, the concentrated detergent slugs removed much more oil than the dilute solutions. However, the effectiveness of the slug process depends on many variables. The quantity of oil removed is increased markedly by increasing the flooding rate. The efficiency is also influenced by the type of crude, type of reservoir rock and initial water saturation. Therefore, a careful analysis of each reservoir system is required before the economic value of the process can be determined. INTRODUCTION It is well known that the displacement of oil by invading water during water flooding is far from complete. It is generally agreed that the unrecovered oil is retained in the porous medium by the capillary forces which may be relatively large compared to the forces generated by the flowing water. Therefore, it was logical that some early workers should turn to surface-active materials to reduce the capillary forces to facilitate the release of oil. As early as 1927,' a patent was granted for the use of surface-active materials in water flooding. In 1932, when soap solutions were passed through Bradford and Venango sands, it was reported that the results were inconclusive, erratic and that "further investigation is needed to determine exactly the function of the solution and to obtain a clearer insight into the phenomena involved."' Some of the modern scientific reports conclude with a similar statement,' showing that the lack of agreement on the mechanism of oil removal by wetting agents is still very widespread even though several comprehensive studies have been reported.'." Although there is a lack of agreement as to the general effectiveness of the detergents for water flooding, most investigators do agree that all of the common detergents are strongly adsorbed onto the solid surfaces of the reservoir. In the early calculations it appeared that all additives would be lost before reaching much of the formation area which contained the additional oil to be removed. Experiments indicated that if the usual small waterflood concentrations of wetting agents were used, the rate of advance of detergent through the formation would be only a small fraction of the rate of advance of the flood front. Indeed, some investigators4 felt that the use of wetting agents would never be economically feasible because of their adsorption. For example, DunningG estimated that the wetting agent in concentrations of 25 ppm, would advance only 0.05 times as fast as the flood front. Ojeda, et al,' found that a surfactant in a concentration of 10 ppm moved less than 0.01 times as fast as the flood front. It is significant, however, that both investigators found that increased concentrations of wetting agents moved faster, relative to the flood front, than solutions at the lower concentrations. Ojeda showed that an extrapolation of his data indicated a relative rate of 0.5 at 1 per cent concentration, while Dunning6 estimated a relative rate of 0.46 for a 1 per cent concentration. It was obvious that these concentrations could not be used for continuous injection because the cost of the injected detergent would far exceed the value of additional oil produced. Traditionally, detergents are used in very low concentrations for they show good

By ARCHIBALD DOUGLAS

BY this time almost everyone knows, in a general way, the corporate income distribution policies of the 1936 Revenue Act, and many of the practical problems arising there under. This article is not intended to be a technical discussion of that act by title, subtitle, section, or supplement, nor an analysis of inter- dependent sections of the various acts over many years woven on the fiscal loom f our Congressional machine. Such a discussion would require the spinning of a web of words too long for patience. Yet ,a general statement of the underlying plan of the 1936 Act, so far as it affects dividend policies, is perhaps useful.

Jan 1, 1937

By Paul A. Farrar, Harold Margolin

The system Ti-Cr has been re investigated From 40 to 100 pct Cr. The high-temperature modification of TiCr, was found to exist in the temperature range from 1365 where it terminates in the eutectoid reaction TiCr,(TI)* — HE chromium-rich region of the Ti-Cr system was investigated by Vogel and Wenderott,' Mc Quillan,' Van Thyne et dl.,' and Cuff Duwez and Taylor determined the crystal structure of the low-temeperature modification of TiCr, to be fcc a = 6.943A and Levinger' discovered the existence of a second (high-temperature) modification of TiCr, and determited its crystal structure to be hexagonal a = 4.932A, c/a = 1.617i. No information was obtained as to the temperature range over which each modification of TiCr? existed; therefore the present investigation was initiated. I) Experimental Techniques Alloys employed for the delination of this system were prepared from iodide titanium and high-purity chromium. The purity of these materials is as follows: Iodide titanium: purity 99.99 pct; major impurities—carbon 0.0001 pct; oxygen 0 to 0.002 pct; nitrogen 0 to 0.002 pct; silicon 0 to 0.005 pct; manganese 0.001 pct; copper 0.001 pct (Foote Mineral Co., Lot 609-29). Chromium #1: metallic purity 99.997 min.; interstitial content—oxygen 0.27 to 0.46 pct; hydrogen 0.028 to 0.038 pct; nitrogen 0.0002 pct (Ave-quipo Inc.). Chromium #2: purity 99.9 pct; major impurities—carbon 0.01 pct; oxygen 0.013 pct; nitrogen 0.02 pct; silicon 0.01 pct; sulfur 0.03 pct; iron 0.01 pct (Fulmer Research Institute Ltd.). A total of sixteen alloys of thirteen different compositions was prepared in the range from 40 to 95' *All percentages are given in weight percent. pct Cr. The compositions of the alloys prepared were as follows: Ti-40, 45, 50, 60, 62, 64, 66, 68, 70, 80, 85, 90, and 95 pct Cr. Two buttons were prepared of the 66, 90, and 95 pct Cr alloys. The 40 pct Cr and one of the 66 pct Cr alloys were prepared from the chromium # 2. All the other alloys were prepared from chromium #1. The alloys were arc-melted as 25-g buttons in a copper-hearth glass-walled furnace7 under an inert atmosphere of high-purity helium. The alloys were sintered at 250 amp and melted twice at 350 amp for 30 sec with the buttons being turned over between melts. Weight losses during melting were determined and in the range 45 to 68 pct Cr they were found, in all cases, to be less than 1.25 pct of the total alloy weight. A number of the high-chromium alloys shattered during cooling from either the first or second melt, which made the weight loss considerably larger than usual. The 70 and 80 pct alloys lost approximately 5.7 pct of their total weight, the 85 pct alloys 1.5 pct, the 90 pct alloy 2 pct, and the 95 pct alloy 3 pct. However, it is felt that the actual composition of the alloys in this region is probably within approximately 1 pct of the intended composition, as a large portion of the material lost was that due to shattering after melting. Nominal compositions were therefore used in plotting data and referring to the alloys. The alloys were cut into specimens, wrapped in molybdenum sheet, and encapsuled in argon-filled quartz or Vycor tubes for heat treatment. The heat-treatment times and temperatures are given in Table I. The specimens were quenched in iced brine (I.B.Q.) following heat treatment. The standard techniques of grinding, polishing., and etching were used in preparing the specimens for metallo-graphic examination. For alloys below 68 pct Cr

Jan 1, 1963

By William Hurst

Muskat's depletion performance equation is here derived considering the expansion behavior of the reservoir hydrocarbon system and a simple fractional-flow equation. This nietkod of derivation leads logically to the two extensions that follow. The first of these is concerned with gravity segregation in a depletion-drive reservoir. The second is concerned with including an empirically determined tern? for water influx in the performance equation. The more general equation for gravity segregation when there is a primary gas cap and empirically-determined water influx is stated for completeness. These equations have been found useful in reservoir performance calculations in Eastern Venezuela. A discussion on the methods of solving these equations follows, and considers firstly the effect of taking finite intervals in the numerical integration, and sec-ondly, methods of incorporating the time functions involved in segregation in with the expansion behavior. The paper concludes with a brief general discussion on further extensions to the depletion performance equation. INTRODUCTION The two fundamental sources of energy by which oil is produced from a reservoir result from pressure depletion inside the boundaries of the reservoir and fluid encroachment across the boundaries of the reservoir. The wells in either case form low pressure outlets through which oil and gas may be produced by the expansive force of the reservoir fluids and associated encroaching fluids. When the reservoir pressure is higher than the bubble-point pressure of the oil, so that there is no free gas in the reservoir, these expansive forces are the only ones available for the production of oil. However, when the reservoir pressure is less than the bubble-point pressure of the oil, free gas is vaporized as the pressure falls. With both oil and free-gas phases present, the additional forces of gravity and capillarity may operate on the gas-oil system, as they have previously operated on the oil-interstitial water system. Gravity tends to segregate the free gas from the oil due to their density difference. Capillarity opposes and eventually balances gravity as the more extreme free gas and oil saturations are reached, preventing the independent move- ment of free gas until it is above a certain saturation, and the independent movement of oil when it is below a certain saturation. The type of depletion performance equation chosen for predicting the future performance of a reservoir depends on the amount of past history available. When the reservoir is somewhere past the halfway mark in depletion, some form of decline curve is often used. With less past history, material balance equations which incorporate empirical factors based on the past performance are often used. When, however, the amount of past history is small, the Muskat depletion performance equation will usually be used. The distinguishing feature of this type of equation is that empirical factors based on the over-all or macroscopic reservoir behavior are almost or entirely absent. Each parameter affecting the reservoir performance is ascribed an independent set of values based on measurements made on laboratory samples; that is, incorporating microscopic empirical factors. In establishing Muskat-type depletion performance equations, it is necessary to consider the reservoir as consisting of a number of associated blocks, in each of which the saturations and pressures may be considered uniform, and in each of which all substances have uniform pressure-volume characteristics. Thus, a primary gas cap can usually be considered as one block and an aquifer as another. Gravity segregation may be negligible for practical purposes when the rock and oil properties are adverse and/or the dip or thickness of the reservoir is too small. In this case the whole oil leg may be considered as one block, except in very large reservoirs. In very large reservoirs the fluid and rock properties may vary enough, particularly in the dip direction, for it to be necessary to divide the oil leg into a number of blocks, in each of which the relevant quantities may be considered uniform. When gravity segregation of the oil and free gas is not negligible, it is necessary to consider the space occupied by the initial oil leg as divided into two blocks, a secondary gas cap and an effective oil leg, in each of which saturations may be considered to be uniform. The total volume of these two blocks is thus constant, but the secondary gas cap grows continuously at the expense of the oil leg. Muskat1 derived depletion performance equations for the basic case of an oil reservoir with closed boundaries and without segregation, and for the case of an oil