Search Documents

By Charles W. Perry

The options of enhanced oil recovery, coal syncrude, and shale syncrude are compared by approximately equivalent economics. The physical constraints for the major enhanced oil recovery processes are described, followed by new estimates of cost. The range for all three options in terms of light syncrude equivalent are $22 to $40 per barrel in 1980 dollars.

Jan 1, 1982

By R. E. Ray, J. W. Stevenson, J. A. Berry

Conventional concrete block plastered with a cementitious coating is the most common material used in the construction of permanent stoppings to direct airflow in underground mines in the US. All mines experience various degrees of strata convergence depending on depth of overburden, geological conditions, and type of roof support employed. Strata convergence will cause cracks and joint openings in masonry stoppings, resulting insignificant air leakage losses. Where strata convergence is severe, complete structural failure of the stopping can ultimately occur. Reconstruction of damaged or destroyed stoppings adds expensive overhead to mining operations, and even greater expenses are incurred from the additional fan horsepower required to overcome leakage losses. Ideally, a stopping should maintain high resistance to airflow while yielding to strata convergence. By properly incorporating a polyisocyanurate rigid foam material within the masonry block structure, stopping service life can be increased in mines experiencing strata convergence problems such as floor heave, roof loading, and lateral rib movement.

Jan 1, 1986

By L. S. Castleman, R. K. Hotzler

We are currently studying the effects on recrys-tallization of impurities diffused into dispersion-hardened alloys. Our interest in this phenomenon was originally aroused by the observation that the recrystallization temperature range of tungsten "doped" with alumina and silica, or with thoria, is lowered drastically if nickel is plated onto the tungsten prior to heat treatment.' In this note, we report a similar effect that sulfur has on the recrystallization behavior of thoriated nickel. The experimental procedure for this exploratory phase of the investigation has consisted simply in heating commercially obtained stress-relieved samples of thoriated nickel for varying temperatures and times in sealed capsules containing air and small quantities of sulfur. The samples contain 2.4 vol pct thoria and initially less than 18 ppm S by weight; they are prepared either from 0.5-in.-ciiam rod stock or from 0.092-in. sheet and are in the "as-received" (stress-relieved) condition prior to exposure. In an atmosphere free of sulfur, such samples do not show evidence of recrystallization after being annealed for 1 hr at a temperature of 2500°F (1372C).2 The photomicrograph in Fig. 1 shows the microstructure of one of our samples annealed for 75 hr at 1000° C (1832°F) in a sulfur-free capsule. The grain structure is hardly evident (if at all) at 465 times magnification. In contrast, the photomicrograph of Fig. 2 shows the recrystallization that has taken place in a sample exposed to sulfur for 5 hr at 1000°C (1832°F). A nickel sulfide phase is visible at the grain boundaries of the light-appearing grains. We have also observed recrystallization to occur in a sample annealed at 600°C (1112°F) for 25 hr. This temperature is below the 637°C (1178°F) eutectic in the Ni-S system. In the latter case, no nickel sulfide phase is evident in the microstructure. Moreover, we have noticed the occur-

Jan 1, 1969

By Ralph A. Sherman, John Blizard

The experimental investigation described in this paper was conducted to determine the relative combustibilities of different samples of blastfurnace coke when burned in a current of air in a small furnace. It was undertaken in connection with the work done by Perrottl and Kinney2 on the process of combustion in the blast-furnace hearth.3 Reference is often made to the "combustibility" of coke by blastfurnace men, but exactly what is meant by the term "combustibility" is somewhat vague. Brassert,4 in a paper before a meeting of blastfurnace men in 1914, refers to combustibility as follows: The value of the coke in relation to the heat reactions in the furnace is determined not only by the carbon content but even more so by its combustibility. This, in turn, is governed by its size, the physical and chemical composition of the carbonaceous substance forming the cell walls, and the interior and surface structure of the coke pieces. These properties are, in turn, influenced by the chemical and physical properties of the coals used for coking, the density of the cake of coal in the oven, the coking time, temperature and heat regulation of the ovens, and last, but not least, by the method of quenching, screening and handling the finished coke. What principally concerns the blast furnace is the rate of progression of the combustion, which depends not so much on the chemical analysis as on the physical qualities of the coke. It is this rate of progression that we term combustibility, which is the speed at which the carbon molecules in the coke combine with oxygen under given conditions. In general, what the blast furnace requires is a coke which will burn rapidly and with intensity at the tuyeres, yet which has a sufficiently strong structure and hard surface to resist abrasion and solution by CO2 in the upper part of the stack.

Jan 1, 1923

By W. C. Lilliendahl, H. W. Highriter

The method developed and used in this laboratory for the production of metallic uranium of such purity that it is ductile and can be cold-worked to fine wire or thin sheet by rolling has already been described1. It consists, briefly, in the electrolysis of potassium uranous fluoride (KUF5) in a molten bath composed of equal parts of sodium and calcium chlorides. The bath is contained in a graphite crucible, electrically heated to about 775° C., the crucible serving as the anode for electrolysis. The uranium deposits in finely divided form mixed with salts upon a molybdenum cathode suspended axially in the crucible. Upon completion of the electrolysis the cathode is removed and cooled, the deposit broken and leached to remove salts. The metal powder is washed with water and dilute acetic acid and dried in vacuo to reduce oxidation. Suitable amounts are then prcssed into pellets and heated in vacuo by high-frequency induction, using a thoria crucible. The uranium melts and flows away from the pellet, leaving a shell, which is largely oxide. In general, this method produced a satisfactory metal, although at times tile uranium was not ductile. The investigations recorded here were made to find the cause of this embrittlement. It was known that the metal generally contained carbon, derived from disintegration of the graphitc crucible in which electrolysis is conducted, in amounts dependent upon the thoroughness of washing the metal powder. Accordingly, analyses of several samples, both ductile and brittle, were made by combustion and absorption of CO² in Ascarite, using air instead of oxygen to reduce the temperaturc and rate of oxidation. Several of these metals were made with special precautions to reduce carbon content. The results show no relationship between ductility and carbon content in the range investigated (Table 1). Microscopic examination of ductile and brittle metals disclosed the presence in the latter of an intergranular constituent, harder than the matrix and less easily oxidizable, which was absent from the ductile material. Rough estimates of the volume of the hard constituent

Jan 1, 1935

By John Blizard, Ralph A. Sherman

The experimental investigation described in this paper was conducted to determine the relative combustibilities of different samples of blastfurnace coke when burned in a current of air in a small furnace. It was undertaken in connection with the work done by Perrottl and Kinney2 on the process of combustion in the blast-furnace hearth.3 Reference is often made to the "combustibility" of coke by blastfurnace men, but exactly what is meant by the term "combustibility" is somewhat vague. Brassert,4 in a paper before a meeting of blastfurnace men in 1914, refers to combustibility as follows: The value of the coke in relation to the heat reactions in the furnace is determined not only by the carbon content but even more so by its combustibility. This, in turn, is governed by its size, the physical and chemical composition of the carbonaceous substance forming the cell walls, and the interior and surface structure of the coke pieces. These properties are, in turn, influenced by the chemical and physical properties of the coals used for coking, the density of the cake of coal in the oven, the coking time, temperature and heat regulation of the ovens, and last, but not least, by the method of quenching, screening and handling the finished coke. What principally concerns the blast furnace is the rate of progression of the combustion, which depends not so much on the chemical analysis as on the physical qualities of the coke. It is this rate of progression that we term combustibility, which is the speed at which the carbon molecules in the coke combine with oxygen under given conditions. In general, what the blast furnace requires is a coke which will burn rapidly and with intensity at the tuyeres, yet which has a sufficiently strong structure and hard surface to resist abrasion and solution by CO2 in the upper part of the stack.

Jan 1, 1923

By W. C. Lilliendahl, H. W. Highriter

The method developed and used in this laboratory for the production of metallic uranium of such purity that it is ductile and can be cold-worked to fine wire or thin sheet by rolling has already been described1. It consists, briefly, in the electrolysis of potassium uranous fluoride (KUF5) in a molten bath composed of equal parts of sodium and calcium chlorides. The bath is contained in a graphite crucible, electrically heated to about 775° C., the crucible serving as the anode for electrolysis. The uranium deposits in finely divided form mixed with salts upon a molybdenum cathode suspended axially in the crucible. Upon completion of the electrolysis the cathode is removed and cooled, the deposit broken and leached to remove salts. The metal powder is washed with water and dilute acetic acid and dried in vacuo to reduce oxidation. Suitable amounts are then prcssed into pellets and heated in vacuo by high-frequency induction, using a thoria crucible. The uranium melts and flows away from the pellet, leaving a shell, which is largely oxide. In general, this method produced a satisfactory metal, although at times tile uranium was not ductile. The investigations recorded here were made to find the cause of this embrittlement. It was known that the metal generally contained carbon, derived from disintegration of the graphitc crucible in which electrolysis is conducted, in amounts dependent upon the thoroughness of washing the metal powder. Accordingly, analyses of several samples, both ductile and brittle, were made by combustion and absorption of CO² in Ascarite, using air instead of oxygen to reduce the temperaturc and rate of oxidation. Several of these metals were made with special precautions to reduce carbon content. The results show no relationship between ductility and carbon content in the range investigated (Table 1). Microscopic examination of ductile and brittle metals disclosed the presence in the latter of an intergranular constituent, harder than the matrix and less easily oxidizable, which was absent from the ductile material. Rough estimates of the volume of the hard constituent

Jan 1, 1935

By B. Woyski

Many writers, in discussing defects caused by oxidation and gassing of bronzes and red brasses advocate substantially the same cure for both. But from its nature, oxidation cannot take place if there is an excess of fuel in the furnace, while the gases absorbed by some alloys are products of incomplete combustion of the fuel. Hence the metal can be either oxidized or gassed, but it is doubtful whether these actions can take place simultaneously. Oxidation can be easily overcome by the use of deosidizers or it may be avoided by protecting the molten metal with suitable fluxes. Absorption of gascs is more difficult to overcome: the regulation of the air and fuel, so as to produce complete combustion, and the protection of the bath by mineral fluxes arc the most important factors. Gas expulsion, resulting in gas holes, porosity, unsoundness, and swollen or cauliflower-headed risers, is said to have several causes. One writer1 lists the most common causes in the order of their importance, as follows: Superheated metal, dirty or slaggy furnace conditions, using metals low in quality or those previously subjected to bad melting practice, poor grade of fuel, use of newly lined or damp ladles, indiscriminate mixing of scrap or illogical combinations of metal. Superheating the metal usually occurs when the heat is ready to be poured but for some reason must be held in the furnace. In this case, a careful furnace tender tries to avoid overheating the metal by keeping a mild fire; that is, a reducing fire which, unfortunately, results in gassing the metal. A dirty, slaggy furnace may result in gassing the metal by retarding the heating and prolonging the time necessary to bring the metal to the proper temperature, thereby increasing the chances of gassing in uncertain furnace atmosphere. It is doubtful whether rnetals of low quality have anything to do with gassing molten metal, except, possibly in the case of metals containing

Jan 1, 1923

By B. Woyski

Many writers, in discussing defects caused by oxidation and gassing of bronzes and red brasses advocate substantially the same cure for both. But from its nature, oxidation cannot take place if there is an excess of fuel in the furnace, while the gases absorbed by some alloys are products of incomplete combustion of the fuel. Hence the metal can be either oxidized or gassed, but it is doubtful whether these actions can take place simultaneously. Oxidation can be easily overcome by the use of deosidizers or it may be avoided by protecting the molten metal with suitable fluxes. Absorption of gascs is more difficult to overcome: the regulation of the air and fuel, so as to produce complete combustion, and the protection of the bath by mineral fluxes arc the most important factors. Gas expulsion, resulting in gas holes, porosity, unsoundness, and swollen or cauliflower-headed risers, is said to have several causes. One writer1 lists the most common causes in the order of their importance, as follows: Superheated metal, dirty or slaggy furnace conditions, using metals low in quality or those previously subjected to bad melting practice, poor grade of fuel, use of newly lined or damp ladles, indiscriminate mixing of scrap or illogical combinations of metal. Superheating the metal usually occurs when the heat is ready to be poured but for some reason must be held in the furnace. In this case, a careful furnace tender tries to avoid overheating the metal by keeping a mild fire; that is, a reducing fire which, unfortunately, results in gassing the metal. A dirty, slaggy furnace may result in gassing the metal by retarding the heating and prolonging the time necessary to bring the metal to the proper temperature, thereby increasing the chances of gassing in uncertain furnace atmosphere. It is doubtful whether rnetals of low quality have anything to do with gassing molten metal, except, possibly in the case of metals containing

Jan 1, 1923

By Frank C. Greene

Drilling in Missouri in 1943 continued at a lower rate than in 1942, only 28 wells being completed. Following the completion of the Cities Service Oil Company's No. I Jim Cook near Tarkio, in the northwest corner, NW. 'fi sec. 32, T. 65 N., R. 39, W., Atchison County, four dry holes were drilled by other parties, all a mile or more from the Cook well. Later the Cities Service Oil Co, completed No. 2 Cook for 60 bbl. Table I gives a summary of activities by counties. The total footage drilled was 23,83134 ft., of which 12,802 1/2 ft. was by cable tools and 11,029 by rotary. Four of the dry holes were drilled into Mississippian or older beds.

Jan 1, 1944

By Frank C. Greene

Drilling in Missouri in 1943 continued at a lower rate than in 1942, only 28 wells being completed. Following the completion of the Cities Service Oil Company's No. I Jim Cook near Tarkio, in the northwest corner, NW. 'fi sec. 32, T. 65 N., R. 39, W., Atchison County, four dry holes were drilled by other parties, all a mile or more from the Cook well. Later the Cities Service Oil Co, completed No. 2 Cook for 60 bbl. Table I gives a summary of activities by counties. The total footage drilled was 23,83134 ft., of which 12,802 1/2 ft. was by cable tools and 11,029 by rotary. Four of the dry holes were drilled into Mississippian or older beds.

Jan 1, 1944

By Alfred F. Brainerd

A few months since, Prof. Lawrence C. Johnson, of the U. 8. Survey, discovered in Mississippi large deposits of carbonate iron-ore, geologically located in the Claiborne formation of the Tertiary Epoch. These deposits are not pockets, but continuous layers or beds extending for miles, and can be located with certainty where they have not been removed by erosion. Upon examination, recently made by G. W. West, Birmingham, Ala., the largest deposits and highest grades of ore were found near Enterprise, Lauderdale county, and in Clark county, Miss. These beds measure from 10 to 18 feet in thickness, are superimposed upon a " burr rock," associated with green sand, and dip 30 feet to the mile southeast, at an altitude of 350 feet above sea-level, can be

Jan 1, 1888

By E. H. Wells, A. Andreas

Greater progress than in any previous year was accomplished by the oil industry in New Mexico in 1936. The total number of completions in the state was 631, of which 549 were oil wells, 21 were hydrocarbon gas wells, three were carbon dioxide gas wells, and 58 were dry holes. The total oil production for the year was 26,804,446 bbl. Compared with the production for 1935 of 20,228,947 bbl., this represented a gain of 32.5 per cent. Of the total production, 25,337,382 bbl. came from Lea County. The average daily nonmarginal well allowable for that county was 115 bbl. the first of the year and 86 bbl. at the close. Production was regulated by the New Mexico Oil Conservation Commission,

Jan 1, 1937

By Donald B. Gillies

PROBABLY the most critical and difficult period in an engineer's career is that between the completion of his college work and his attainment of professional recognition and accepted status in the industrial world. Upon leaving school the young graduate breaks his immediate ties with his educational institution and in a sense finds himself adrift. At this time in his life a society like our Institute has both the responsibility and the privilege of meeting a vitally important need in his professional life. Some of these young men are Student Associates, in the year after graduation, and some are Junior Members, but all need advice and assistance. In some respects this situation will be accentuated by the war. Not only will thousands of young engineers be mustered out of military service but the process we describe generally as industrial reconversion will make necessary many readjustments in personnel. About two years ago the Institute recognized the opportunity of helping the younger member to help himself by appointing a new standing committee to be known as the Committee on Professional Development of Junior Engineers. Herbert Hoover is Honorary Chairman and it is my privilege to serve as Chairman. The name of the Committee is not entirely satisfactory but it expresses the general objective. The present article is in the nature of a progress report of the work of this Committee.

Jan 1, 1945

By AIME AIME

THE 123d meeting of the Institute was held in New York Feb. 14 to 17, 1921. The total registration was 1199, as compared with 1138 at the New York meeting in 1920. The weather was a strange and welcome contrast to that of last year, when New York was buried under six feet of snow as the result of the fiercest blizzard in its history. This year there was no snow, and the weather was said to be much more like an Arizona winter than New York. A complete program of the Technical Sessions is on p. 9. The discussions of the papers presented will be published in pamphlet form as soon as possible and will be noted in MINING AND METALLURGY in the usual way.

Jan 1, 1921

By AIME AIME

MORE than thirty members of the Coal Division attended the Coal Land Valuations Round Table on Monday morning. Chairman Dilworth stated that the Committee had been appointed to take up the question and, after reading the list of members of the Committee, pointed out that the object of the meeting was to formulate a plan of action rather than to discuss any phases of valuation, per se. To this end he presented a tentative outline of points to be considered in the future by the Committee. After a lively discussion on the desirability of inclusion of some questions in the agenda of the Committee, the following outline was adopted :

Jan 1, 1931

By Eugene McAuliffe

MANAGEMENT and control of any body of workmen can be effected through various - well-known methods ' though many managers hold certain personal theories of control that range from an absolute dictatorship to what might be called the principle of laissez faire, or the "let alone" method. Managements of many mines, factories, smelters and refineries have been compelled in recent years to accept certain restrictions in hours of labor as well as in methods employed, imposed either by federal or state laws, or by labor agreements. Broadly speaking, regulations of the above character were brought on the industry by managers who failed to recognize fully the rights of their employees to proper sanitary, safe, and compensatory working conditions, as well as working hours that were proper and just. As an example of poor management and worse psychology, we have only to hark back to the days when many bituminous coal operators maintained an inadequate number of pit cars for the number of miners or loaders employed, or if the pit cars were available, the haulage facilities

Jan 1, 1934

By A. B. Kinzel

SILICON and its metallurgical uses have been the subject of speculation since the earliest days of modern civilization. The early philosophers, Theophrastus and Pliny, believed that silica was a special form of ice, an opinion that was not seriously challenged until the seventeenth century. The first comprehensive view of the nature of silica was advanced by Lavoisier in 1787. He assumed silica to be an oxide of an unknown metal. In 1808 Berzelius produced ferrosilicon by heating silica, iron and charcoal. Probably the first produc¬tion of crystallized silicon was in 1854 when H. St. C. Deville accidentally produced the material while electrolyzing a double chloride of aluminum and sodium containing siliceous impurities. It is not strange that the early investigators should have given so much attention to silica and silicon, because of the great natural abundance of the former. Although silicon does not exist in the elemental state in nature, it has been estimated that the lithosphere contains approximately 60 per cent silica; quartz and rock crystal are found in practically every part of the world.

Jan 1, 1933

The Howe Memorial Lecture, in memory of Henry Marion Howe, Past President of the Institute, was authorized in April, 1923, as an annual address to be delivered by invitation under the auspices of the Institute by an individual of recognized and outstanding attainment in the science and practice of iron and steel metallurgy or metallography, chosen by the Board of Directors upon recommendation of the Iron and Steel Division. The following were the Howe lectures and lecturers for the years indicated

Jan 1, 1929

By H. W. Gillett

CLYDE WILLIAMS has reminded me that in the fall of 1929, gave, in MINING AND METALLURGY, an account of the hopes and aspirations of Battelle Memorial Institute, which was then just swinging into initial operation; and that therein I remarked that B.M.I. should stand, as well, for Better Metallurgical Industries, since helping to better them was the Institute's aim. So he has suggested that some of the betterments of the past fifteen years might well be listed. A yearly summary of progress comes pretty close to the ultimate in futility, for everything proved of value in that year had its inception in earlier years, and everything really new has still to be proved. Plenty of things hailed as wonderful achievements for that year, by some enthusiasts invited to contribute to the summary, turn out in later years to be inglorious flops. But over a decade and a half, betterments that are really such become self-evident, and recounting some of them can be done without guesswork or wishful thinking. An inventory of what was known and utilized in 1929 compared to what is now known and used is not too hard to make. Perhaps the most clear-cut picture of what is known and used at a certain date is drawn by the handbooks, textbooks, and equipment catalogs of that date, with scientific periodical literature forecasting what knowledge may later be used when it is verified and assimilated. The tools available for production or for research limit the application of old and the finding of new knowledge.

Jan 1, 1945