Search Documents

By George F. Comstock

It has been reported recently1 that the hardenability and toughness of forging steels may be improved appreciably by the use of complex deoxidizers containing titanium, aluminum, and vanadium. In the light of these results, an investigation of similar deoxidizers containing various hardening and grain-refining elements was proposed. These deoxidizers included three manganese-silicon-aluminum-titanium al- loys with and without boron and calcium, three titanium-aluminum ferroalloys with vanadium, molybdenum and zirconium, respectively, an aluminum-zirconium ferroalloy, and plain ferroboron. Their approximate compositions are given in Table I, and the results obtained so far in the investigation of their effects on steel are presented in the later parts of this paper. Method of Using Deoxidizers The deoxidizers listed in Table I were used in three series of 0.40 per cent carbon steels, which were melted in a small basic-lined induction furnace and cast in the form of I7-lb. ingots about 2.75 in. square. The basic charge for each heat was 10 lb. Armco iron and 6 lb. of clean low-carbon sheet-steel scrap. When melted, this charge was deoxidized with 15 grams of ferrosilicon, then about 500 grams of pig iron was added to give the desired carbon content. After the pig iron was dissolved, nickel shot and high-carbon ferrochromium were added if required, and additions of 80 per cent high-carbon ferromanganese and 50 per cent ferrosilicon were made to provide the proper amounts of those elements. Aluminum was added to every heat 2 min. after the silicon, for grain-size control and preliminary deoxidation. One minute later the special deoxidizer was added to the clean bare surface of the molten steel, and 2 min. afterward the steel was poured into the ingot mold, using a hot-top and pipe-preventing compound after pouring to decrease the depth of the shrinkage cavity. The special deoxidizers were used mostly in the form of about ½ to¾-in. lumps,

Jan 1, 1942

By George F. Comstock

It has been reported recently1 that the hardenability and toughness of forging steels may be improved appreciably by the use of complex deoxidizers containing titanium, aluminum, and vanadium. In the light of these results, an investigation of similar deoxidizers containing various hardening and grain-refining elements was proposed. These deoxidizers included three manganese-silicon-aluminum-titanium al- loys with and without boron and calcium, three titanium-aluminum ferroalloys with vanadium, molybdenum and zirconium, respectively, an aluminum-zirconium ferroalloy, and plain ferroboron. Their approximate compositions are given in Table I, and the results obtained so far in the investigation of their effects on steel are presented in the later parts of this paper. Method of Using Deoxidizers The deoxidizers listed in Table I were used in three series of 0.40 per cent carbon steels, which were melted in a small basic-lined induction furnace and cast in the form of I7-lb. ingots about 2.75 in. square. The basic charge for each heat was 10 lb. Armco iron and 6 lb. of clean low-carbon sheet-steel scrap. When melted, this charge was deoxidized with 15 grams of ferrosilicon, then about 500 grams of pig iron was added to give the desired carbon content. After the pig iron was dissolved, nickel shot and high-carbon ferrochromium were added if required, and additions of 80 per cent high-carbon ferromanganese and 50 per cent ferrosilicon were made to provide the proper amounts of those elements. Aluminum was added to every heat 2 min. after the silicon, for grain-size control and preliminary deoxidation. One minute later the special deoxidizer was added to the clean bare surface of the molten steel, and 2 min. afterward the steel was poured into the ingot mold, using a hot-top and pipe-preventing compound after pouring to decrease the depth of the shrinkage cavity. The special deoxidizers were used mostly in the form of about ½ to¾-in. lumps,

Jan 1, 1942

By Edward A. Vitunac

The emerging importance of pneumatic conveying systems for bulk materials is largely due to the economic advantages such systems frequently exhibit when compared to alternate methods. Included in these advantages are relative simplicity, ease of installation, flexibility, ease of maintenance, cleanliness, safety and ease of automation to the degree desired. In general, installed costs favor a pneumatic system when compared to competing mechanical systems if the transporting distances are long or to and from many points. In addition, supplemental use such as cooling, heating, or drying may supply the incremental value required to justify its selection.1 The main disadvantages of a pneumatic system are the greater horsepower required per unit weight of material conveyed, material limits in abrasiveness, and density. In addition, material breakage tends to increase at changes of direction and at any obstruction such as that caused by the imperfect butting of two pipe sections in the conveying line. Classification of the material at the discharge may also cause problems in dusting and segregation. Materials weighing less than 4 lb per cu ft tend to cause feeding and collecting problems although they can be conveyed easily. Material between 4 lb and 20 lb per cu ft can be handled with fewer problems, but flow rate is hard to predict. The 20-60 lb per cu ft range offers best results, whereas materials of over 60 Ib per cu ft tend to drop out of the air stream and settle in the pipeline unless careful pro- visions are made to prevent this.2

Jan 5, 1968

By H. O. Hofman

THE leading antimony mineral is stibnite. In smelting stibnite ore two processes are available, precipitation and roasting-reduction. The former is suited only for high-grade ores. As low-grade ores are more common than high-grade, roasting-reduction is of greater importance than precipitation. In the roasting process the aim may be to leave the oxidized antimony in the ore, or it may be to volatilize as much of the antimony as possible, collect the volatilized oxide as a rich intermediary product and smelt it for antimony, leaving the gangue poor enough to be considered a waste product. Whichever way the roast is conducted certain difficulties inherent in stibnite are encountered. These are: 1. The low melting point of stibnite which; according to Pelabon,1 is 550°C., according to Wagemann2 540°C., and according to Borgström3 546°C. 2. The ignition temperature: According to Friedrich,4 stibnite, if heated in air, begins to oxidize at 290°C. if the size of a grain is 0.1 mm. in diameter; at 343°, if 0.1 to 0.2 mm.; and 430° if 0.2 mm. 3. The fusibility of a mixture of Sb2S3 and Sb203 which in the form of kermesite (Sb2S3)2.Sb203 melts at 517°C.5 4. The volatility of Sb2S3 and Sb203, for which no numerical data appear to exist, although practical experience has shown that they are volatile at low temperatures.

Jan 1, 1916

By Zay Jeffries

THIS paper will include a brief discussion of Prof. Howe's paper on The Supposed Reversal of Inheritance of Ferrite Grain Size from that of Austenite.1 The general subject of grain refining in steel and iron will also be treated. The conclusions reached are stated in the following hypotheses which are discussed more in detail below. 1. The ferrite grain size in pure iron, the ferrite and pearlite grain size in hypoeutectoid steel, the pearlite grain size in eutectoid steel and the cementite and pearlite grain size of hypereutectoid steel are not inherited from the grain size of the mother austenite. 2. The only structural feature that is generally inherited from the austenite of hypo- and hypereutectoid steels on cooling through their transformation ranges is the position of the excess ferrite or cementite at the austenite grain boundaries, sometimes causing complete and sometimes incomplete networks which outline the old austenite grain boundaries. Rapid cooling through the transformation range will cause the non-inheritance of this structural (network) feature. 3. The austenite grain boundaries themselves are nearly always effaced in all steels and also in pure iron during the Ar transformations. 4. The grain-size refining of steel and iron is brought about by the combined. effect of non-inheritance of the transformation products on either heating or cooling, i.e., the austenite transformation .products do not inherit their grain size from the austenite on cooling through the transformation range for does austenite inherit its grain size from the products which form austenite on heating. 5. In general, in both iron and carbon steel the larger the austenite ,grain size, the larger will be the grain size of the transformation products on cooling. This, of course, assumes all other conditions constant except the austenite grain size. An exception is found to this general rule in very pure iron such as electrolytic iron. 1n this instance small austenite grains may form very large ferrite grains on cooling through Ar3.

Jan 11, 1917

By James H. TaVoularis, William J. Wiehagen

This paper discusses the application of commercially available microcomputers for assisting trainers in the delivery and evaluation of new hire, refresher, and occupational training. A brief overview of mine training highlights major issues facing the mine training community. The use of computer-based training has a potential for reducing costs and improving the transfer of conventional training to the job.

Jan 1, 1983

By G. W. Traer

THE distillation of bituminous coals at what is commonly termed low temperature, and the quantities, nature and adaptabilities of the products have been the subject of considerable experimentation, during recent years. Fortunately, the earlier work in this country was done by men whose scientific training qualified them properly to record and interpret the results of-their experiments. The work of Prof. Parr, of the University of Illinois, is especially notable in this respect. Prof. Parr's work, added to that of English experimenters, demonstrated certain things to a degree which is generally regarded as convincing. They have proved that a caking bituminous coal, when subjected to a temperature of not more than 1000° F. (preferably somewhat less) will yield light tar having low specific gravity (about 1.06) and high value; also, that this yield, with a given coal, will depend upon the percentage of hydrocarbons in the coal, the maximum temperature used, and the promptness with which the distillate gases are removed. It is assumed that air is excluded from the retort, and that the coal is subjected to heat for a sufficient time to drive off all of the tarry hydrocarbons. The results attained in the first, or low-temperature stage of the Carbocoal process, recently described by C. T. Malcolmson, corroborate these general principles. It is the purpose of the writer to describe other work of a practical nature, directed toward the commercial adaptation of these principles, which was begun nearly two years ago; this investigation was assisted by A. J. Sayers, of the Link-Belt Co., and Carl Scholz.

Jan 9, 1918

By E. H. Cho

INTRODUCTION Activated charcoal has been used for several centuries in many capacities including the recovery, isolation and purification of various materials (1). The first use of charcoal in a gold metallurgical system was in the extraction of gold after chlorination (2, 3,4). The gold was dissolved in a chlorine system and subsequently filtered through charcoal. The application of charcoal with cyanide extraction was patented by Johnston (5) in 1894 and adopted commercially in Australia in 1897. The process consisted of dissolving the gold and silver in a potassium cyanide solution and passing it through a series of charcoal filters. The charcoal was subsequently smelted to recover the gold and silver. The interest in the use of charcoal diminished in the first part of the twentieth century as the practice of the use of zinc as a precipitating agent increased. However, in 1916, the Yuanmi Mine in Australia replaced their zinc precipitation plant with a charcoal adsorption plant. In 1926, Scott and Gross (7) of the U. S. Bureau of Mines con- ducted extensive research on the adsorption of gold and silver from cyanide leach solutions. Among their findings was the result that the most important factor in improving the adsorptive power of charcoal was heat treatment with oxidation by air or steam. The work of Zadra (8) in 1952 stimulated renewed interest in the use of activated charcoal in gold and silver recovery with the development of a method of recovery of the gold and silver from the charcoal other than its destruction by burning. The process involved simultaneous desorption

Jan 1, 1983

By S. Korman, S. B. Tuwiner

Chalcocite flotation is affected by agitation intensity during conditioning. Sodium sulphide in minute quantity may activate or depress, depending on conditions. Oxygen is a depressant while oxygen and sulphide neutralize each other by re-action at the mineral surface. Diffusion across a stagnant film at the surface governs reaction rates, while film thickness is reduced upon increase of agitation intensity.

Jan 2, 1950

By T. S. Liu, E. A. Peretti

A LITERATURE survey of the In-Sb system, which was made before a study of the binary diagram was undertaken, revealed that the intermediate phase InSb existed and that its crystal structure is face-centered cubic of the zinc blend type. In 1929 Goldschmidt' determined the lattice constant for InSb and obtained a value of 6.452A. A more recent value, 6.461A was reported by Iandelli2 in 1941. The purity of the indium used was not very high, however. The indium used by Iandelli contained 2 pct Ge. In view of this fact it was decided to remeasure the lattice parameter using high-purity indium (99.97+ pct In) and spectrographically standardized antimony of the highest purity available (99.91 pct Sb). Specimens corresponding to the InSb composition were made by carefully weighing the ingredients on an analytical balance and heating them in vacuo in a quartz tube at 700°C. As melting losses were negligible, the alloys were not analyzed chemically, but the intended analysis was taken as being accu- rate. Powder samples were prepared by either filing or crushing of the brittle alloy, followed by screening at 325 mesh. The powders were then annealed at 400°C in evacuated capsules for about an hour. X-ray photograms were taken with a Debye and a back-reflection focusing camera, using characteristic cobalt K. radiation. Lattice parameters were calculated by Cohen's³ method. The results of a Debye pattern and of a back-reflection pattern at 25°C are given in Tables I and 11. The lattice parameter at 25 °C is 6.47602A.

Jan 1, 1952

By Strathmore R. B. Cooke, Robert E. Brandt

EARLIER work1,2 has shown that the strength developed by fired magnetite pellets containing silica or silicates is due to three separate effects. Two of these are associated with the formation of slag in the interior of each pellet at temperatures above 1000°C, where the atmosphere is substantially though temporarily neutral. The third is independent of the silica content and is responsible for the development of a hard shell around the pellet during the initial stages of firing, a condition which permits the pellet to assume the increasing load of the overlying burden and prevents extrusion of the slagged and semi-liquid interior. Pellets made from hematite concentrates do not show these effects unless specific additives are incorporated, and it is these differences in behavior which in large part account for the difficulty in producing satisfactory pellets from such concentrates. Elsewhere it has been stated that "the most important factor responsible for the development of strength in fired magnetite pellets containing no additive is the oxidation of magnetite to hematite and the subsequent recrystallization and grain growth of this constituent."1 The object of the investigation reported in the present paper was to study in detail the mechanism described above and to evaluate its contribution to the strength of the fired pellet compared with other possible mechanisms, excluding slag bonding. This was effected by placing together polished faces of two cubes prepared from specific minerals and then heating them under constant pressure at different temperatures both in air and in nitrogen.

Jan 4, 1954

By Zay Jeffries

This paper will include a brief discussion of Prof. Howe's paper on The Supposed Reversal of Inheritance of Ferrite Grain Size from that of Austenite.l The general subject of grain refining in steel and iron will also be treated. The conclusions reached are stated in the following hypotheses which are discussed more in detail below. 1. The ferrite grain size in pure iron, the ferrite and pearlite grain size in hypoeutectoid steel, the pearlite grain size in eutectoid steel and the cementite and pearlite grain size of hypereutectoid steel are not inherited from the grain size of the mother austenite. 2. The only structural feature that is generally inherited from the austenite of hypo- and hypereutectoid steels on cooling through their transformation ranges is the position of the excess ferrite or cementite at the austenite grain boundaries, sometimes causing complete and sometimes incomplete networks which outline the old austenite grain boundaries. Rapid cooling through the transformation range will cause the non-inheritance of this structural (network) feature. 3. The austenite grain boundaries themselves are nearly always effaced in all steels and also in pure iron during the At transformations. 4. The grain-size refining of steel and iron is brought about by the combined effect of non-inheritance of the transformation products on either heating or cooling, i.e., the austenite transformation products do cst inherit their grain size from the austenite on cooling through the transformation range nor does austenite inherit its grain size from the products which form austenite on heating. 5. In general, in both iron and carbon steel the larger the austenite grain size, the larger will be the grain size of the transformation products on cooling. This, of course, assumes all other conditions constant except the austenite grain size. An exception is found to this general rule in very pure iron such as electrolytic iron. In this instance small austenite grains may form very large ferrite grains on cooling through Arg.

Jan 1, 1918

ALTHOUGH the refining period of the heat is generally defined as starting after the charge has been completely melted, it may more properly be considered as beginning with the first efforts to facilitate the shaping up of the slag and the making of corrective additions for the control of slag or metal composition. Such actions may be initiated during the latter half of the lime boil. The early part of the refining period may, then, in essence overlap the latter part of the melting period. The primary aims of the refining period are: (1) to reduce phosphorus and sulfur from the steel bath to levels safely below the maximum contents specified; (2) to eliminate carbon to a specified level as rapidly as possible and still allow time for proper conditioning of the slag and attainment of the necessary bath temperature; and (3) to have the heat ready for tapping or furnace deoxidation, with slag in the proper physical and chemical condition, and with carbon and oxygen contents and the temperature of the steel at the proper levels for the composition and grade of steel being produced. The particular conditions that fulfill these aims are distinctly different, depending upon whether the steel is to be finished according to fully killed. semikilled, or rimming practice and also depending upon the carbon range specified. Regardless of the type of charging practice employed, the object of the refining period is to produce repeatedly the desired finishing and tapping conditions for the grade of steel being produced. The variations and proportions of raw materials used in the charge may cause some variations in the degree of control required during refining, but not in the method of control. The refining period can therefore be discussed from a viewpoint largely independent of charging and melting practice. SHAPING UP THE SLAG In the first helper's vocabulary, refining practice consists in

Jan 1, 1951

By E. S. Bardwell

THE reverberatory copper-refining furnaces at the Great Falls Reduction Dept. of the Anaconda Copper Mining Co. have used successively, as fuel, lump coal on grates, pulverized coal, oil and natural gas. In no other plant, so far as can be ascertained, has such a variety of fuels been used. This fact affords a unique opportunity for comparing the relative efficiency obtained with these several fuels under nearly identical conditions. FURNACES The present furnace refinery at Great Falls was placed in operation in April, 1916. The original installation consisted of two furnaces, each with hearths 36 by 14 ft. and provided with fire boxes 10 by 12 ft. for firing lump coal on grates. These furnaces had air-cooled sand bottoms and chrome-brick side walls both above and below the metal line. The roofs were of 12-in. silica brick. Each furnace was provided with a waste-heat boiler of approximately 400 boiler-hp. capacity. We soon found that chrome brick was very unsatisfactory as sidewall material because of its excessive spalling. At the first opportunity the furnaces were rebuilt, using magnesite brick below the metal line and silica brick from the metal line to the roof. At the same time the thickness of the side walls was increased, thus decreasing the width of the hearth to 13 ft. At about this time also, the thickness of the furnace roofs was increased from 12 to 15 in. No further changes occurred in furnace design until 1922, when the use of lump coal on grates was abandoned in favor of pulverized coal.

Jan 1, 1932

By Howard L. Hartman

Probably no aspect of underground excavation is as important or as neglected as the environment. The Committee on Rapid Excavation, formed by the National Academy of Engineering to study the technological needs for "rapid" underground excavation in tunnels, shafts, and mines of the future, encountered a blank wall in attempting to evaluate environmental needs. In fact, so little quantitative information on the extent of present-day hazards is available that projection of future environmental-control demands must await more adequate assessment of current hazard levels. Further, there are not even accepted tolerance standards for many environmental conditions, such as heat, noise, and illumination. Only certain atmospheric contaminants have been satisfactorily catalogued. Any technical study, therefore, which purports to examine the state-of- the-art on underground environmental control must, in reality, settle for a cursory survey of a rather nebulous subject. ENVIRONMENTAL HAZARDS To contend adequately with hazards in the underground environment requires some knowledge of their nature and characteristics. In this regard, it is helpful first to identify our concern: when, where, and to whom or what may environmental conditions constitute "hazards"? Table 1 summarizes considerations that are important in this regard. For the purposes of this Conference (and book), primarily directed toward the excavation process itself, the hazards of consequence occur during excavation (item A) and primarily within the excavation (item B). However, some attention must be given to external hazards as well, since these may affect excavation. The object of concern (item C) is mainly human safety, although property security is also important. Hazards occur in a variety of forms. If one is to devise suitable control

Jan 1, 1970

By G. S. Cole, G. F. Bolling

Fluid flow strongly influences ingl structure and the columnar -to-equaaxed transition. Artificial flow patterns siwzilar to the nuturul ones act to induce this transition, while dampening forces act to suppress this transition. It is shown here how simple mechanical forces can be applied to a systerrz in order to induce or slipPvess relative fluid flow and the change both the structure transition and the exact structures obtained. The example used is the effect of slow rotations and oscillations 012 a cooling- ingot (of laboratory scale). The details of rotution and oscillation for various cooling rates, lenlperal~ire gradients, and sizes of ingot are related to other solidzfication variables. THE grain structure of a casting can be changed by altering the fluid motion during solidification. Just how important these changes are depends directly upon the degree to which the fluid motion can be controlled. An early step in understanding the nature and influences of fluid motion was taken by studying natural thermal convection; when a static mechanical device was used to suppress natural flow the result was opposite to that obtained when an electromagnetic device was used to augnlent flow in a pattern similar to the natural one. ''2 Suppression allowed more columnar growth to occur, but "augmented natural convection" brought about an earlier columnar-to-equiaxed transition (CET). Since the solidification of a free ingot must have characteristics somewhere between those displayed during suppression and augmentation, we know that natural convection must influence the CET. Further, since heat transfer in the liquid is always some time-dependent combination of convection and conduction, it can easily be guessed that the temperature gradient in the liquid is the vital factor affecting the CET.1,2 It is obvious that the structure arising from the unadulterated solidification of an ingot, without external influence, is rarely if ever the best possible one. Although the pattern of the natural fluid flow may be considered efficient, the magnitude of the flow and the heat transfer decrease freely from the outset. For a

Jan 1, 1968

By G. L. Oldright, Henry de Rycker, S. F. Ravitz

The upper limit of richness of concentrates that can be smelted by means of the blast furnace without added diluents is fixed by the operation of sintering. A sinter feed with normal gangue constituents, containing more than about 50 per cent of lead, tends to fuse; as a result, air does not come sufficiently into contact with the sulphides at roasting temperatures, and sulphur elimination is poor. Since most lead concentrates now contain 55 to 80 per cent lead, it is necessary to add diluents to lower the grade of such sinter feed to about 50 per cent or less. This not only entails the expense of providing barren diluents when adequate diluents containing precious metals are not available but also appreciably lowers the capacity of the blast furnace to produce lead and increases slag losses. Attempts to desulphurize rich lead concentrates by methods other than sintering have not proved successful. Flash roasting, for example, converts much of the lead sulphide to lead sulphate rather than to oxide. However, this suggested the possibility that deliberate flash roasting of the concentrates to sulphate, followed by sinter roasting of the resulting product, might prove promising, particularly inasmuch as the elimination of sulphur from lead sulphate requires heat alone and not contact with atmospheric oxygen. The sintering of lead sulphate products has additional interest because important amounts of such products are now treated by lead smelters. Considerable quantities of lead sulphate are present in rich lead flue dusts and other by-products; lead-chamber sulphuric acid plants and other

Jan 1, 1944

By R. W. Moore, A. B. Kinzel

Although the iron-carbon diagram has undergone many changes in the last 20 years, the region below the eutectoid line and up to approximately 1.7 per cent carbon has been little affected. This region is generally considered to consist of cenlentite and ferrite. Graphite has been noted occasionally in the hypereutectoid steel region, and the ready formation of graphite nodules in malleable cast iron is a phenomenon difficult to interpret in the light of cementite, supposedly stable at sub-eutectoid temperatures. In this case the graphite formation has been partly explained by the presence of silicon, and many have believed that silicon acts to change the stable state rather than to accelerate reactions so as to arrive at the stable state in a briefer period of time. Consideration of this phenomenon indicates that cementite is not the stable phase in the temperature composition zone referred to. In the course of examining a low-carbon steel tube taken from a petroleum cracking still, which had been in service for approximately three years at temperatures somewhat below the eutectoid temperature, observations were made that shed light on this entire subject. The tube in question analyzed:' C, 0.15 per cent; Mn, 0.49; Si, 0.02; S, 0.023; P, 0.015. The microstructure of the tube after service is shown In Figs. 1 and 2. From these it is evident that cementite as such is absent, and that in its place nodular graphite has been formed. In order to check this observation further, samples taken from the tube were heated at 850" C. for varying periods of time. The small samples were put into a large hot furnace, and the total time is recorded. The structure of the sample after 5 min. at 850" C. is shown in Figs. 3 and 4, and the nest of pearlite surrounding the graphite nodules is most satisfactory evidence of the character of the nodules. As the length of time of heating at this temperature increases, the pearlitic zone increases, with final restoration

Jan 1, 1935

By R. W. Moore, A. B. Kinzel

Although the iron-carbon diagram has undergone many changes in the last 20 years, the region below the eutectoid line and up to approximately 1.7 per cent carbon has been little affected. This region is generally considered to consist of cenlentite and ferrite. Graphite has been noted occasionally in the hypereutectoid steel region, and the ready formation of graphite nodules in malleable cast iron is a phenomenon difficult to interpret in the light of cementite, supposedly stable at sub-eutectoid temperatures. In this case the graphite formation has been partly explained by the presence of silicon, and many have believed that silicon acts to change the stable state rather than to accelerate reactions so as to arrive at the stable state in a briefer period of time. Consideration of this phenomenon indicates that cementite is not the stable phase in the temperature composition zone referred to. In the course of examining a low-carbon steel tube taken from a petroleum cracking still, which had been in service for approximately three years at temperatures somewhat below the eutectoid temperature, observations were made that shed light on this entire subject. The tube in question analyzed:' C, 0.15 per cent; Mn, 0.49; Si, 0.02; S, 0.023; P, 0.015. The microstructure of the tube after service is shown In Figs. 1 and 2. From these it is evident that cementite as such is absent, and that in its place nodular graphite has been formed. In order to check this observation further, samples taken from the tube were heated at 850" C. for varying periods of time. The small samples were put into a large hot furnace, and the total time is recorded. The structure of the sample after 5 min. at 850" C. is shown in Figs. 3 and 4, and the nest of pearlite surrounding the graphite nodules is most satisfactory evidence of the character of the nodules. As the length of time of heating at this temperature increases, the pearlitic zone increases, with final restoration

Jan 1, 1935

By C. A. Worner

THE meeting of the Petroleum Division at the Annual Meeting of the Institute maintained the high standard set in previous years, and attendance of member: of the Division was at a new high. The impact of the war was evident not only in the tone of many of die papers but also in the presence at the meeting of many of our members now serving in the armed forces of our-country. Ken interest was manifested in all papers presented and the discussions which followed developed many additional facts of interist and importance. The first activity of the Division was the joint meeting of the Papers and Programs and the Publications Committees on Monday afternoon; at which time definite plans were formulated for a simplification and co-ordination of the work of the committees.

Jan 1, 1944