Search Documents

By C. E. McManus

MANY mechanical advances have been made on mining equipment during the year 1951. There have been a number of trends established and many modifications made on open-pit equipment to increase the efficiency and availability of all the machines necessary in the moving of overburden and iron ore. Some years ago, the trend toward larger shovels for the loading of off-highway trucks began, but in the last year, it has become general practice to use the 5 to 7 ¼ -yd quarry-type shovels in the loading of haulage units. For years these larger shovels were used in the locomotive haulage pits. As the truck capacities increased from 15 to 20 to 30 tons, the need for larger loading units became apparent. Today in most mines, large shovels are in evidence and a few 8-yd shovels will be delivered this year for loading off-highway trucks. Torque Converter-Shovel The Diesel-driven shovel with its friction bands has been modernized with the torque converter. There have been about ten shovels remodeled to take a torque converter in the drive system. The large high-torque, low-speed Diesel engine was removed and replaced by a high-horsepower, high-speed, automotive-type engine. This engine was connected directly to the torque converter. The torque converter was connected to the shovel through the standard original sprocket and chain. Dual governors controlled engine performance. One governor controlled the high idle of the engine; the other governor, which is connected through a flexible shaft to the output shaft of the converter, controlled the loading of the engine. With this dual governor hook-up, the engine anticipates load conditions and is operating at high idle and full throttle before the shovel load is transmitted back through the converter to the flywheel. It has been found that with this automotive-type engine and converter, the shovel capacity has been increased about 20 pct. Also, the wear on the friction bands, breakage of hoist cables, and other mechanical breakages has been reduced materially. Alloy-Steel in Shovels The shovel equipment manufacturers have been experimenting with low-temperature-strength, high-alloy steels to combat the excessive breakage that occurs in extremely cold weather. High-nickel alloy steel has been used in critical areas that are affected by low temperatures, the most notable being dipper sticks. Most shovels ordered today are equipped with some of this special, alloy steel. More and more manganese alloy is being used for replacement parts such as shovel pads, idlers, drive sprockets, etc. Although the initial cost of these parts is considerably higher than the standard replacement items, the life of these manganese parts is considerably longer and well worth the added expenditure. Dipper-teeth repair is still a problem. Most companies use the small replaceable inserted tooth. It has become common practice among some of the companies to "job out" their dipper-tooth repairs to outside welding companies. This necessitates an additional inventory of teeth, but it does guarantee an adequate supply of replacement teeth at all times. These contractors have set up their shops on a production basis and can do an acceptable job at a high rate of speed. Thermite welding has been used in retipping teeth. To date, the process cannot be called successful but with improvements the time required to repoint the dipper teeth will be decreased considerably. The submerged arc process has been tried in the replacement of these dipper points, but like thermite welding has not proven successful. Here again, if a method can be developed to use submerged arc, the job of teeth repair will be made much easier. New model shovels in 6 ½ and 8 cu yd sizes fea-

Jan 1, 1952

By John G. Hall

The unstable metal market during 1949, with resulting lower metal prices, has focused every mine operator's attention on the problem of reducing operating costs. Improvement in mining, methods, use of modern mechanical mining equipment, and increasing the efficiency of the labor force are the tools with which we will have to work. Careful planning is necessary to coordinate all phases so that no one phase is overdone. A mine may become over-mechanized if, for instance, capital charges against new equipment exceed the savings in labor costs, or where a large enough tonnage is not produced. The cooperation, of labor is essential to any mechanization program. There have been too many instances where mechanization and improvements have done nothing more than make up for a decrease in labor efficiency, thus bringing the production of labor back to its old standard. The operator has gained little and labor has gained only a "softer job." In any mechanization program there are gains to be had by both the operator and labor. By the efficient application of modern equipment and improved mining methods the operator should gain by decreased costs, and labor may profit by receiving a share of these decreased costs.

Jan 1, 1950

By Charles D. Walcott

Jan 1, 1901

By Harlowe Hardinge

AN extensive recent trip throughout the mining districts of the Southwest, Central West, an Northwest,' reveals a numbes of interesting conditions that have influenced operators, in both large and small mills, to modify their flow sheets insofar as they pertain to crushing and grinding. The changes made and planned for the future should be of interest. It is interesting to note when traveling through the country, how ideas change and practice is modified, and it is rather amusing to see how milling methods seem to run, more or less, in cycles. New ideas and developments are brought about which run through the industry and are taken up by many of the best and most well informed operators. Some of them will change, sooner or later, back to their old practice; for, like everything .else, what will work well in one place will not necessarily be suited to another. On the other hand, it is often difficult to establish. other practices known to be of value, owing to the natural resistance to make a change, but on the whole, the western mill men seem to be more alive to possible benefits of various modifications than any other engineers with whom I have come in contact in all parts of the world. Mill men in other parts of the world always keep in con- tact with what is being done in the western part of the United States, but it does not necessarily follow that those in the western part of the United States are always right. Some of these changes that have been made and afterward abandoned will be referred to later.

Jan 1, 1929

By W. N. Best

(San Francisco Meeting, September, 1915) INTRODUCTION CRUDE oil attracted attention because of its excellence as a fuel for open-hearth furnaces; for making crucible steel and brass; for melting copper, lead, tin, zinc, nickel, silver, malleable iron, gray iron; and for the production of steam in all sizes and types of boilers. For heating furnaces, mold-drying ovens, core ovens, ore roasters, calciners, hot-air furnaces, sand drying, asphalt road work, etc., its superiority over other fuels is due to the fact that the heat is at all times under perfect control, so that a constant temperature may be attained and maintained at the will of the operator. This means a maximum amount and uniform quality of work. Crude oil is of two kinds, paraffine base and asphaltum base, and varies from 11 to 46 gravity Baumé. The light-gravity oil does not require heating before use; but oil of less than 20 gravity Baumé should be heated to just below its vaporizing point, in order to reduce its viscosity and to obtain the highest efficiency of combustion. Heavy California oil vaporizes at 230°'F., Mexican crude oil at from 175° to 210° F., and Beaumont, Texas, oil at 142° F. Fuel oil vaporizes at 130° F.

Jan 8, 1915

By Roy A. Anderson, Roger H. McConnel

The Metaline district from 1906 through 1965 has produced nearly 16 million tons of ore yielding 400,808 tons of zinc and 178,062 tons of lead. The sediments, ranging from Precambrian into the Devonian, are schist, phyllite, conglomerate, greenstone, quartzite, limestone, dolomite, and carbonaceous slates. Quartz monzonite and granodiorite of the Cretaceous(?) Kaniksu batholith are exposed over a large area beginning a few miles south of the district. There is minor Tertiary conglomerate and basalt. Abundant glacial deposits obscure much of the bedrock. Northeasterly trending folds, having steep to overturned northwesterly limbs, and thrust faults, striking northeasterly and dipping southeasterly, characterize the deformation of the Precambrian and Paleozoic rocks. Recent drilling indicates that the Slate Creek fault, too, is also a southeasterly dipping thrust fault. This new evidence suggests that the Valley Block, like the other major structural blocks, may in part be a thrust plate rather than a graben, and that thus the district may have greater structural unity with the surrounding region than has heretofore been apparent. The Cambrian Metaline Formation of limestone and dolomite contains essentially all the lead-zinc mineralization. Most of the ore mined to date has come from a carbonaceous and irregularly siliceous breccia of sedimentary and diagenetic origin, locally called the "Josephine Horizon," that makes up the top few to 200 feet of the formation. The Josephine Unit is a breccia of gray limestone, coarse light gray dolomite, very thin-bedded, dark gray siliceous dolomite, and "zebra rock" believed to be of algal origin, embedded in a matrix of black dolomite or black jasperoid or some mixture of these two. The jaspcroid fragments and irregular blobs embedded in the black dolomite matrix and the jasperoid laminae in the very thin-bedded dark gray dolomite suggest that jasperoid was formed at the same time as the breccia matrix and as the laminated dolomite. So too, the marked tendency of sphalerite and galena to be disseminated mainly in the dark breccia matrix and their tendency to be most abundant in the jasperoid laminae of the very thin-bedded dark gray dolomite, even where the mineralized and laminated dolomite is fragmented and engulfed in black dolomite breccia matrix, suggests that in these ha bits the sulfides also were deposited contemporaneously with the sediments. Yet very commonly, veins and vague veinlets and patches of white quartz, usually carrying rather coarse sphalerite and sometimes galena crosscut all rock types. These contradictory relationships throughout the Josephine Unit suggest that both the black jasperoid and the sulfides were original constituents of the Josephine Unit but that, locally, they later were remobilized and deposited as white quartz and coarser grained sulfides. Possibly, at least in part, this "metamorphism" is one of the effects produced during or shortly after the intrusion of the Kaniksu batholith.

Jan 1, 1968

By Wiley C. Buford

Gary Works No. 1 BOP Shop is a three furnace shop which went into operation December, 1965. The heat size is over 200 tons, with a substantial percentage of the production used to feed a Continuous Slab Caster. Vessels are driven by a shaft mounted bull gear and main housing utilizing eight 35 HP flange mounted motors and primary gear reducers. Torque absorption is controlled by two spring actuated torque arms. At 1:00 p.m. on Thursday, August 6, 1970, as "E" furnace was being turned down for a preliminary test, the drive side trunnion bearing failed. The furnace dropped slightly and shifted several inches north in the direction of the drive unit. The decision was made to tap the heat which was done without incident and the vessel uprighted. No attempt was made to completely drain the slag from the vessel, so as to avoid any further damage to the trunnion shaft bearing surface. The bearing failure occurred approximately four years and eight months after start up of the shop. Unfortunately ?M? furnace had gone down for a normal reline two days prior to the bearing failure, leaving the shop with only one operating furnace.

Jan 1, 1972

By C. L. Berrier, Wm. B. Daly

Jan 1, 1923

By Wm. B. Daly, C. L. Berrier

Jan 1, 1923

By Thomas A. Simpson, Tunstall R. Gray

The Birmingham district first produced steel from Alabama hematite ores in 1899. Since then, the district generally produced more than 6.0 million gross tons of ore a year to the late 1950's. Production has declined since then to an annual rate of about 1.5 million gross tons. Reserves calculated for the district are sufficient to last many years. Mining in the district is now confined to Woodward Iron Company's Vance and Pyne mines. The rocks exposed consist of about 15,000 feet of consolidated Paleozoic sediments with a thin veneer of unconsolidated Cretaceous sediments in the Vance area. The district is characterized by a distinctively parallel and subparallel, slightly arcuate series of faults and joint systems. In view of available information, it seems reasonable to conclude that the Birmingham red ores are of sedimentary origin, modified to a small extent by diagenetic replacement after original deposition.

Jan 1, 1968

By R. A. Kinzie

In a conventional cement plant, the drying and heating of the raw material takes place in the upper section of a cylindrical kiln where the heat exchange is poor. In a Lepol kiln this part of the process is carried out on a traveling grate where the heat exchange is efficient. The increase in fuel economy justifies the greater complexity of the installation.

Jan 1, 1950

By Dara P. Antia, Morris Cohen, Frank S. Gardner

THERE is a conspicuous lack of information in the literature on the precise role played by residual quantities of austenite in heat-treated steels. While retained austenite may be expected to have significant effects on such important properties as the impact resistance of tools and carburized parts and the dimensional stability of dies and gauges, attempts to study these problems systematically have suffered from the absence of a reliable technique for ascertaining absolute amounts of austenite. With such a technique, not only could the relation between residual austenite and service behavior be investigated, but the chemical and heat-treatment factors that control the quantity of the austenite could also be established. Thus, the retained austenite content could then be regulated in accordance with the results desired. The presence of retained austenite may be inferred by observing the changes in properties (hardness, specific volume, electrical resistance, etc.) due to its decomposition on subatmospheric cooling1 or on tempering,2 but these indirect measurements are not readily translated into percentages of austenite. Quantitative determinations have been achieved in special cases by means of dilatometric3 and magnetic4,5 measurements; but the former procedure requires that observations be conducted during the hardening and involves difficult calibrations that limit its applicability, while the magnetic procedure is very sensitive to extraneous influences and depends upon assumptions that can only be considered as approximate in an absolute sense. Furthermore, both the dilatometric and magnetic effects are volume properties, and cannot be conveniently utilized to explore variations in retained austenite from point to point in a specimen. Some microstructures lend themselves to accurate evaluation of retained austenite contents by metallographic methods,3 but such instances are not too common, and at best, the procedure is tedious. The characteristic X-ray diffraction lines of austenite permit positive identification of its presence; and in the present paper the intensities of these lines, or the corresponding densities* on photographic film, are employed to measure the amount of the retained austenite. In order to cancel the effect of uncontrollable variations in the X-ray exposure and film-development conditions, a standard reference line is superimposed on each film by maintaining a foil of aluminum in the path of the incident X-ray beam during the entire exposure. With different samples of steel and the same foil, the ratio of the density of some one austenite line to the density of

Jan 1, 1943

By Graham Bright

The rapid increase in reliability, the low cost of operation, the ready application of safety devices, and the growing availability of central-station power have made the question of installing a hoist of the electric type no longer debatable. Where adequate electric power is available, there are few cases where it would be advisable to install a steam or air hoist. The type of electrical equipment depends largely on the nature of the power supply, its capacity, and the form of the power contract under which power is purchased. In a large majority of cases, the available electric power is alternating current, three phase, 60 cycles. There is, however, considerable 25-cycle power in use; and in a few instances constant voltage direct current is the only power available for a small or an occasional medium-size hoist. Where a new hoist is to be installed, the designer of the mechanical parts can readily take care of the maximum stresses likely to be imposed by the motor. Where the hoist is already installed and operated by steam or air and it is desired to substitute an electric motor for the engine, a careful check should be made to determine the advisability of using the old mechanical parts. In most cases it is better to install a complete new hoist than to attempt to use old mechanical parts. A steam engine has a definite maximum torque, which the hoist has been designed to withstand, while a motor may be able to deliver momentary torques beyond the strength of the mechanical parts of the hoist. The selection of the proper type of electrical equipment can only be made after complete information is obtained and certain calculations made to determine the capacities required. There are several methods used in making hoist calculations, but no matter what method is utilized a fair degree of familiarity with hoists and hoisting conditions is necessary before an intelligent analysis and proper selection can be made. Forms Used in Hoisting Calculations Some of the hoist calculation methods are long and complicated. Where such calculations are seldom made, it is better to use the

Jan 1, 1922

By A. B. Parsons

AT the outset, the authors of this paper desire to file a disclaimer and an, explanation. They have no inside information from occult sources; neither of them feigns clairvoyant powers in the slightest degree. It is true that they have indicated on be graphs an approximate trend for the consumption of seven important mineral commodities up to the year 1954. At best this is a risky business; the figures do not pretend to be any- thing more than reasoned conjectures that are predicated on an attempt to evaluate some of the more obvious of the many factors that are likely to have a bearing on the future.

Jan 1, 1937

By T. W. Guy

IN approaching the problems of sampling coal, a brief statement of certain facts that are more or less taken for granted may he helpful: 1. The coal-mine operator needs reliable data as to the physical and chemical characteristics of his coal in order to plan and control intelligently its mining, preparation, and marketing. The consumer needs such data in order to select the equipment and the coal best suited to meet his requirements, to check the quality of fuel delivered, and the efficiency of its use. Various government control agencies require such data as a basis for classifications and establishment of limits, for use in carrying out the requirements of federal, state or municipal laws. 2. All such data must be obtained by analyses, measurements, or tests made on samples, which are taken to represent the coal tested. It is now becoming generally recognized that, in accordance with statistical laws, test results from samples are not expected to represent the exact qualities of the lot or lots from which they are taken, except within statistical, or "expected" limits. Such limits are definitely specified by some present standards of the American Society for Testing Materials and the British Standards Institution. 3. Samples that give ash within satisfactory limits are usually assumed to be sufficiently accurate for other analyses, except under special conditions such as meeting close specifications for coals showing wide variability in sulphur, fusibility of ash, or other quality. 4: In. modern coal sampling the increment is recognized as the basis for taking samples. For a given accuracy the number and weight of increments specified are increased with: (a) the expected ash, and (b) the top size designation of the lot to be sampled. 5. It is extremely important that every sampler recognize that: the specified number and weight of increments are minimums, and that. the precautions to be used in order to take them properly are also minimums; that in the reduction of the gross sample the sizes specified for the coal after each stage of the crushing are maximum; that the quantities specified to be taken after each crushing stage are minimum; that any short cuts or failures to meet the requirements specified will reduce the statistical accuracy of the results, although it is possible that one or two checks on a few results may seem to show otherwise.

Jan 1, 1943

By R. E. Zimmerman, T. W. Guy

IN approaching the problems of sampling coal, a brief statement of certain facts that are more or less taken for granted may be helpful: 1. The coal-mine operator needs reliable data as to the physical and chemical characteristics of his coal in order to plan and control intelligently its mining, preparation, and marketing. The consumer needs such data in order to select the equipment and the coal best suited to meet his requirements, to check the quality of fuel delivered, and the efficiency of its use. Various government control agencies require such data as a basis for classifications and establishment of limits, for use in carrying out the requirements of federal, state or municipal laws. 2. All such data must be obtained by analyses, measurements, or tests made on samples, which are taken to represent the coal tested. It is now becoming generally recognized that, in accordance with statistical laws, test results from samples are not expected to represent the exact qualities of the lot or lots from which they are taken, except within statistical, or "expected" limits. Such limits are definitely specified by some present standards of the American Society for Testing Materials and the British Standards Institution. 3. Samples that give ash within satisfactory limits are usually assumed to be sufficiently accurate for other analyses, except under special conditions such as meeting close specifications for coals showing wide variability in sulphur, fusibility of ash, or other quality. 4. In modern coal sampling the increment is recognized as the basis for taking samples. For a given accuracy the number and weight of increments specified are increased with: (a) the expected ash, and (b) the top size designation of the lot to be sampled. 5. It is extremely important that every sampler recognize that: the specified number and weight of increments are minimums, and that the precautions to be used in order to take them properly are also minimums; that in the reduction of the gross sample the sizes specified for the coal after each stage of the crushing are maximum; that the quantities specified to be taken after each crushing stage are minimum; that any short cuts or failures to meet the requirements specified will reduce the statistical accuracy of the results, although it is possible that one or two checks on a few results may seem to show otherwise.

Jan 1, 1950

Jan 1, 1893

Beverley S. Randolph, Frostburg, Md. (communication to the Secretary): It has always appeared to me that each coalseam has its peculiar character or habit, due to the conditions of its formation, by virtue of which it is either persistent or variable in its section over extended areas. One seam will hold its thickness, chemical character, number and position of partings, beds of slate, etc., over a large area, while another will be found to vary in some of these characteristics every few feet. As the position of the outcrop is an accident of the topography, depending on folding and erosion which have taken place since the bed was formed, no one opening in the outcrop, or, in fact, anywhere else, can supply reliable evidence as to the general character of the seam. To determine the character of an untried seam, a number of sections are necessary from widely separated points, in order to show such variations as may exist. Should material variations be developed, more numerous sections are necessary, in

Jan 1, 1901

By J. F. Shirley, H. K. Burke

In January, 1964, three years of laboratory and pilot plant test work reached its culmination. The San Manuel Div. of the Magma Copper Co. switched its molybdenite extraction circuit from the sodium hypochlorite-ferrocyanide process to the new process described in this paper. The San Manuel Div. Concentrator of the Magma Copper Co. is located near San Manuel, Ariz., approximately 45 miles northeast of Tucson. The concentrator treats approximately 35,000 tons of ore per day containing about 0.85% copper and 0.025% molybdenite. The San Manuel ore body is a disseminated copper deposit in quartz monzonite and quartz monzonite porphyry. The primary copper mineral is chalcopyrite; minor amounts of chalcocite, bornite and covellite are also present in varying degrees. Pyrite makes up somewhat more than half the sulfide content of the rock. The molybdenite is nearly always found on fracture faces or associated with quartz veinlets.' On January 9, 1964, the sodium hypochlorite-ferrocyanide process that had been used for molybdenite recovery was replaced by the following process: 1) A conditioning step with hydrogen peroxide, sulfuric acid, sodium cyanide and zinc sulfate. 2) A two stage rougher flotation step with stove oil and sodium ferrocyanide. 3) One cleaning step with sodium ferrocyanide. 4) One cleaning step with sodium hypochlorite and potassium ferricyanide. 5) Four cleaning steps with an anti-foam Exfoam 636 and potassium ferricyanide. COPPER CONCENTRATOR Since molybdenite recovery is closely allied with previous steps in the operation, the copper concentrator will be briefly described first. The ore is ground to approximately 5% plus 65-mesh and 65% minus 200-mesh in a two-step grinding circuit consisting of rod mills in open circuit and ball mills in closed circuit with rake classifiers. A straight forward rougher circuit producing only one concentrate is used. The rougher concentrate is combined with the discharge from the regrind ball mills and is then cycloned, with the overflow going directly to the cleaner circuit and the underflow going to the regrind mills. The feed to the cleaner circuit is approximately 90% to 94% minus 325 mesh. The cleaner circuit consists of two stages in which the tailing from the final cleaner stage is returned to the primary cleaner and the primary cleaner tailing is returned to the rod mill discharge at the head of the circuit. Approximately 0.013 lb of the allyl ester of amyl xanthate (S-3302) per ton of ore is added to the rod mills and approximately 0.006 lb of sodium isopropyl xanthate (2-11) per ton of ore is stage added down the rougher banks. The frother used is methyl iso-butyl carbinol (MIBC) and it is added at various points in the grinding and the rougher flotation circuits. Lime is added to the ball mills and/or to the rod mills to maintain the desired pH in the rougher flotation. The rougher flotation has been operated at various pH levels between 10.5 and 11.5. Fuel oil is added in the regrind mills at a loading of approximately 0.01 lb per ton of ore. Factors Which Directly Affect Molybdenite Recovery: It has been found at San Manuel that, to obtain maximum molybdenite recovery, an oily type flotation collector must be added in the grinding circuit. When molybdenite is crystallized in the characteristic platy form, which appears to be the case almost all of the time at San Manuel, its surface has a greater tendency to adhere to oils than water. 2 Of the several oily type collectors available on the market, the allyl ester of amyl xanthate seems to be the best molybdenite promoter. The floatability of San Manuel's molybdenite does not appear to be affected, at least up to a pH of 11.5, by lime. It has been reported that at several plant operations high lime alkaline circuits have adversely affected the molybdenite recovery.3,4 It has been found through microscopic studies that the bulk of the chalcopyrite will float before the molybdenite in both the rougher and cleaner circuits. It is necessary to add fuel oil to the regrind mills to enhance the

Jan 1, 1965

By R. L. Tobie, H. W. Seaney

Over the years since 1956 when initial experiments were conducted on underground concreting in an attempt to cope with the ground weight and pressure encountered in the development of a large-scale underground block caving system, the use of monolithic concrete linings has grown to include most of the primary development in the mining area. Although the development cost of concrete linings is higher than either timber or steel-supported openings, the repair and maintenance costs are substantially lower, making concrete the most economical means of ground support. Other ad- vantages are also apparent, in that concrete provides superior fireproofing, better ventilation, and a safer, cleaner working place.

Jan 11, 1965