Search Documents

By Ralph Sherman

IN these days of intense competition for the domestic fuel market much is heard of the low efficiencies with which solid fuels, and most particularly bituminous coal, are burned in domestic heating equipment. In contrast to the every-day operating efficiencies of 85 and 90 per cent in large, central, electric-generating stations, efficiencies of 50 per cent and lower are cited for the hand-fired home furnace. Just as the miles per gallon of gasoline is only one of the factors that determine the cost of operation of an automobile, so the thermal efficiency is only one factor in the cost of domestic or other heating. The purpose of this paper is to analyze the total costs of domestic heating by various fuels and types of equipment, to determine the relative importance of efficiency and other factors, and to discuss what this signifies relative to the future of the use of fuels in the home.

Jan 1, 1933

By D. L. Martin, E. R. Parker

DURING the heat-treatment of silver specimens for tensile tests it was observed that the bars blistered and became brittle when heated in a hydrogen atmosphere. [ ] To check this unexpected result, a wide variety of commercial silvers were heated in hydrogen at 850°C, Only a few of the materials developed blisters, the most severe of which is the tube pictured in Fig. I. The microstructure of a cross section of the tube is shown in Fig, 2. The embrittlement is extremely severe at the edge; the blisters result from the severe deforma- [ ] tion of the surface material by large underlying gas pockets, The effects resulting from hydrogen embrittlement of silver have been observed by numerous investigators over a long time1,2,3 although it was only recently that a clear explanation was offered ,4 However, the damage resulting from hydrogen embrittlement has not been generally recognized; and it is of advantage to know more about this phe-

Jan 1, 1943

By H. M. Faust

THERE are a number of different types of power plants. Some use coal to generate steam, others use oil or gas either in the form of steam or internal combustion equipment, while still others avail themselves of water power as a source of energy. A general comparison of the relative power production with different sources of energy in the United States, for several different years is set up in Table 1. This table shows that coal was used to generate 85.6 per cent of the total heat power requirements of 1909, and only 59.2 per cent of the 1930 requirements. The increasing proportion of modern heat energy generated by the use of fuel other than coal is apparent. If coal is to maintain its importance as a source of heat energy, the necessity for its improved perform-ance, in which preparation plays an -important part, cannot be stressed too strongly.

Jan 1, 1933

By W. L. Hill, W. H. Armiger, S. D. Gooch

The physical properties, chemical behavior under thermal treatment, and fertilizer value of fluorine-containing pseudowavellite (hydrous calcium aluminum phosphate) that occurs as phosphate clay admixed with quartz sand in an extensive deposit near Bartow, Fla., were determined by experiments in laboratory, pilot-plant, and greenhouse. When the mineral was heated at 500°C, 80 pct of the phosphorus became citrate soluble. The heated product, however, deteriorates markedly under moist conditions such as obtain in the soil.

Jan 1, 1950

Following the suggestion of Engineering Council and at the direction of, the President, representatives from each of the Federal Government bureaus interested in map-making were called into a conference for the purpose of coordinating all of the Government's map-making activities. This conference has now reported back to the President the results of its findings, which indicate that Engineering Council's recommendation in this matter was well founded. While the conference report states that its members were of the opinion that little duplication of effort existed, it recommends the formation of a permanent Board of Surveys and Maps. An extended review of the map-making activities, which is given as an appendix to the report, indicates that this recommendation is a logical step. The conference recommendations concerning this Board of Surveys and Maps are as follows: (1) the Board is to he com-posed of representatives of mapping bureaus to be assisted by outside engineering organizations, which have been named above; (2) the estab-lishment of an information office in one of the Government bureaus, preferably the Geological Survey, which is to be under the supervision of the Board and is to be a mapping information clearing house for the Government and outside engineering organizations; (3) copyright laws are to be so changed that copies of all. maps made in the United States and with Governmental authority, will go to the central information office; (4) the Government departments are to receive orders to cooperate, with the Board; (5) future topographic maps of all kinds are to conform with specifications for the standard topographic map; (6) the U. S. Coast and Geodetic Survey to have supervision of final adjustment of all important control data under specifications approved by Board of Surveys and Maps; (7) surveys in the form of maps and publications are to be issued as soon as possible after field work has been completed; (8) program of the Interdepartmental Committee on Aerial Surveying was approved. Outside technical and scientific organizations that are called in for consultation are to operate in an advisory capacity only, responsibility for action on Governmental work is. to rest solely with the Governmental agencies.

Jan 12, 1919

By J. V. N. Dorr

DEADWOOD and the Black Hills were familiar names to me from childhood, for. I had an uncle who was among the earliest eastern investors there and I used to hear of the Uncle Sam mine and its rich ore back in the eighties. The spring of my junior year at college, in 1893, brought me an offer of summer work at the Deadwood & Delaware smelter, in Deadwood, and full of the thrill of the long journey from New Jersey, I went out as chemist and stayed four months. Within a week or two of my arrival, I went through the tragic experience of seeing an associate drink cyanide by mistake and die within a few moments. I shall never forget the horror of feeling that my lack of knowledge of an antidote might be responsible for his death, but I found later that the solution he drank was so strong that nothing could have been done. A year after graduation, when I had settled down to chemical research work in New York, an offer came to go back to the smelter in Deadwood, and within a few days I was again tramping down "the Gulch" with my lunch bucket and putting in the standard assay office shift of that day, from 7 a.m. to 6 p.m., with a half-day off on Sundays. During my absence East, the D. & D. smelter had been changed from a pyritic smelter, using native pyrite, and Homestake concentrate to matte the siliceous gold ores, into a copper-matting smelter using copper ores brought from Butte, over the newly-completed Burlington rail-road. The work was interesting, and the laboratory offered many opportunities for making improvements. I remember also undertaking experiments at home on a new method of gold precipitation for the chlorination process and leasing a mine in Strawberry Gulch that promised great things, but soon petered out.

Jan 8, 1927

By AIME AIME

SILVER reached a new high, with the ceiling the limit, at the annual Institute dinner at the Commodore on Washington's Birthday night. Carrying along as ballast other commodities, such as rolls, roses and ferns, souvenir boxes and table number placards, hundreds of silvery balloons, cut loose from their moorings at the tables, bounced idly against the plaster decorations high overhead. At the head table, Scott Turner, retiring President, pre- sided as toastmaster, with the new President, Frederick M. Becket, on his right, and the Chairman of the New York Section, Sydney H. Ball, on his left. Many other distinguished Institute members, medalists, and representatives of organizations and committees, ranged to the east and west. Each had the opportunity at least to rise and bow.

Jan 1, 1933

By J. J. Pelley

NOT being a scientist, an engineer or a metallurgist, I consider it a very great honor indeed to be asked to address the American Institute of Mining and Metallurgical Engineers. Your program indicates that any lack of intricate and technical knowledge on my part in the field of metals will be well taken care of by others. Therefore, I believe any remarks that I have to make might well be devoted to the practical side of metals in railroad service and to the general railroad situation as I view it today. The experiments now being conducted on the railroads with so-called streamlined, light-weight trains and cars would not have been possible had it not been for scientific and engineering research in the past that made these lighter weight metals available. The railroads now have approximately forty units of these new trains in operation. Experi-ence with them will no doubt be a guidepost for future construction in that direction. While the best known experiments are in the passenger service, they are being extended into the freight service. Within the past three years there was constructed for the Association of American Railroads a new standard box car of ordinary carbon steel, in which, by reason of superior design, weight was reduced by 3500 to 4500 lb. under that of existing cars of like capacity. The Association is now testing a box car that weighs approximately six or seven tons less than practically all of the box cars of like capacity in service today. If these tests are successful a very large field for the use of lighter weight metals will immediately be opened, provided the costs of such metals are not too high. The fact that various experiments are being carried on with other classes of equipment constructed with so-called light-weight and non-corrosive metals no doubt will have a considerable effect upon the rebuild-ing of old equipment. The question then will be: How much can we afford to spend on the rebuilding of an old car weighing six to seven tons more than a new car constructed with the latest available materials?

Jan 1, 1936

RACAL COMMITTEE OF ARRANGEMENTS Henry McCormick, Chairman; David Watts, Secretary; H. H. Campbell, A S. McCreath, S H. Chauvenet, C. E. Stafford, George S. Comstock, Jones Wister, E. C. Felton, F. W. Wood, Harvey Fisher. CITIZENS' RECEPTION COMMITTEE Governor H. M. Hoyt, Hon John C. Herman, Hon Simon Cameron, Hon. J. D. Cameron, W T. Hildrup, Charles L. Bailey, W. W. Jennings, Lane S. Hart, H. U. Carter, Gilliard Dock, T. T Wierman, Jr, James Boyd, D. L. Jauss, Dr. T J. Dunott, S. C. Gilbert. William J Rose, James Lynah, Dr. H. B Buehler, William N Lamberton, John Wister, G. M. McCauley, David Fleming, John Q. Donney, M. E. Olmsted, H. S Gross, Henry Gilbert. John B. McPherson, Lyman D. Gilbert, F. W. Forman, L. S. Bent, A. J. Dull, F. R. Leib, Dr. G. W. Belly, James McCormick. The opening session of the meeting was held in the hall. of the Young Men's Christian Association, on Tuesday evening, October 25th. Mr. Jones Wister, of the Local Committee of Arrangements, introduced the Hon. John C. Herman, mayor, who, in a brief address, extended to the members present a welcome to the city, of Harrisburg ; Lieutenant Governor Stone made an address of welcome on behalf of Governor Hoyt and the Commonwealth of Pennsylvania. President Metcalf responded, on behalf of the Institute, to the cordial addresses of the mayor and lieutenant-governor. The following persons proposed for members and associates of the Institute, and recommended by the Council, were unanimously elected :* MEMBERS. William F. Aldrich, - Montevallo, Shelby Co., Ala. George H Blake, - Steelton, Dauphin Co., Pa. L. Bertram Cady, - Salisbury, N. C. John B. Church, - Pottsville, Pa. Walter S. Church, - Pottsville, Pa, Frank L Clark, - Pittsburgh, Pa. * In the following list are included those elected at a subsequent session of this meeting.

Jan 1, 1882

By ERLE VICTOR DAVELER

ERLE VICTOR DAVELER, who in his application for membership in the Institute in 1909 modestly described himself as "millman," was born at Denver in 1885 and graduated from the University of California in 1907. After a few months' work at gold mills in California he went to Tonopah, where for the next two years he had a varied experience working on pumps, convey- ors, tube-mills and filters. For the following two years he was experimental foreman and metallurgical engineer for the Utah Copper Co. at Garfield. He was sent in 1911 to be assistant superintendent of mills at the Ray. From 1913 to 1917 he was mill superintendent at the striking but unsuccessful experiment in large-scale low-grade gold mining of the Alaska Gold Mines Co.

Jan 1, 1929

By J. Van Oirbeek

The ash-fusion gas producer, blown with air preheated to a high temperature, was perfected by the Société des Houilléres de Saint-Etienne during the years 1920 to 1925, for the treatment of a mixture of ashy fuel and limestone. The temperature, about 1800° C., obtained by using hot air in running the producer, ensures the fusion of all the slag and the transformation into carbon monoxide of every particle of carbon contained in the materials treated.

Jan 1, 1937

By Robert E. Green, T. Hinton

The velocities of the three possible modes of elastic-wave Propagation have been calculated for single-crystal aluminum at 1-deg intervals throughout the standard steveographic triangle. The results are presented as isospeed contours. The deviations between the direction of maximum energy propagation and specirzen axes are presented as arrows drawn within the standard triangle. The orientation factors associated with dislocation nzotion on the primary slip system only and also on all twelve slip systenzs have been calculated for all three elastic waves. The orientation factors associated with a longitudinal standing--7aue resonant specivnen hazle also been calculated. The relevance of these results to ultrasonic attenuation measurements is discussed. DUE to the widespread use of ultrasonics in the investigation of the properties of solids a number of authors15 have discussed in detail the theory of elastic-wave propagation in solids. In this paper the modes of wave propagation are evaluated according to the procedure suggested by reeen' for the case of single-crystal aluminum at 1-deg intervals throughout the standard stereographic triangle. The wave speeds are presented in the form of contour diagrams within the standard triangle. The deviations between the direction of maximum energy propagation and the normals to the wave fronts are presented as arrows drawn within the standard triangle. The orientation-de pendent factors (orientation factors) associated with dislocation damping as derived in the preceding paper6 have been calculated for the case of aluminum at 1-deg intervals throughout the standard triangle. The orientation factors for dislocation motion on the primary slip system only and on all twelve slip systems are presented in the form of contour diagrams, for both the traveling- and the standing-wave conditions. The relevance of these results to ultrasonic attenuation measurements is discussed. ELASTIC-WAVE PROPAGATION Three waves can be propagated in a linear elastic homogeneous anisotropic medium. The velocity of propagation v of each of these waves in a medium of density p can be obtained from the determination of the eigenvalues and eigenvectors of the matrix equa- The A's are a series of moduli which are functions of the elastic constants cij and the direction cosines 1, m, and n of the specimen axis. In the case of cubic single crystals where there are only three nonzero elastic constants cll, c12, and C, the A's are, The solution of Eq. [I] will give the wave speeds (eigenvalues) and the direction cosines a, 0, and y of the particle displacements (eigenvectors). To obtain the direction of maximum energy flux requires the calculation of the energy-flux vector ET with com- w is the angular frequency, A, the amplitude, and v the velocity of the wave. The direction cosines a, b, and c of the energy flux vector are then given by

Jan 1, 1967

J. W. RICHARDS*(South Bethlehem; Pa.).-The brass industry would find it very profitable to subsidize researches on the purely scientific determination of the thermophysical properties of the brasses. The data we need most in connection with the brasses are the vapor tension of the zinc from the brasses at different temperatures, the heat of combination of zinc With copper to form different kinds of brasses, and the latent heat of fusion of these brasses at the melting temperature.

Jan 1, 1919

By Clarence M. Haight

The general practice in drill sharpening shops, of which descriptions have been written, is about as follows: The bit is heated to 1600" to 1900°F. Then when forged to the proper shape and size in the sharpening machine, the steel is allowed to cool; it is then passed to a hardening furnace where only the end is heated to about 1450" F., and then quenched in cold water, brine, or in brine with oil on top.

Jan 1, 1922

By W. L. Hill, W. H. Armiger, S. D. Gooch

The physical properties, chemical behavior under thermal treatment, and fertilizer value of fluorine-containing pseudowavellite (hydrous calcium aluminum phosphate) that occurs as phosphate clay admixed with quartz sand in an extensive deposit near Bartow, Fla., were determined by experiments in laboratory, pilot-plant, and greenhouse. When the mineral was heated at 500°C, 80 pct of the phosphorus became citrate soluble. The heated product, however, deteriorates markedly under moist conditions such as obtain in the soil.

Jan 6, 1950

By R. A. Marriot

The steam-generating plant at the Garfield smelter of The American Smelting and Refining Co. consists of two divisions in which the boilers are classed as direct-fired or waste-heat. The direct-fired boiler plant consists of eight 330-boiler hp. type K-19 and S-I 7 Stirling boilers located in the boiler room adjacent to the power house, and two 330-boiler hp. Stirling type K-19 boilers in the reverberatory building, which formerly were connected to a reverberatory furnace but now are arranged for direct firing. All direct-fired boilers are now fired with natural gas. The waste-heat boiler plant consists of all units connected to reverberatory furnaces, and receiving heat from the exit gases therefrom. In this classification there are two 490-boiler hp. Erie City vertical water-tube boilers, and six 330-boiler hp. type K-19 Stirling water-tube waste-heat boilers. Each furnace has boilers arranged in battery setting. The boilers are directly in front of the furnace and connection is made through a short uptake and flue (Fig. 1). The Stirling boiler settings rest on concrete foundations at ground level, with the furnace uptake and flue at a low elevation. The Erie boilers are carried on steelwork some 15 ft. above ground level, and stand against the face of the uptake with no connecting flue. The constructional requirements of a larger furnace dictated this type of setting.

Jan 1, 1934

By F. D. Rosi

IN the production of single crystals by the Bridg-man method of solidification from the melt in vacuum at a crucible lowering rate of 0.25 in. per hr, a cellular structure was frequently observed in copper and copper-base alloys at the terminal surface of the as-cast crystals (i.e., the surface representing the last portion of the crystal to solidify). The geometrical form of this structure varied from crystal to crystal, but, in general, could be classified as either hexagonal or quadrilateral. Fig. 1 shows examples of this cellular structure, which is similar to that reported by Buergerl and, more recently, by Pond and Kessler&apos; and Rutter and Chalmers. In the micrographs of Figs. lb and c, the cubic structure in the alloy crystals is obscured somewhat by excessive surface evaporation in the final stages of solidification. X-ray orientation studies indicate that the traces outlining the various geometrical forms correspond to octahedral planes, which are the planes of greatest reticular density in the face-centered cubic lattice. It would appear from this that the view first propounded by Bravais,4 that the surface energies and normal growth velocities of the different crystal planes are inversely proportional to their reticular densities, applies to this cellular structure, since those surviving are the planes of greatest atomic density. Thus, the observed variation in the geometrical form of this structure in crystals of different orientation is readily understandable from the distribution of the (111) planes in the standard {111}, (1101, and (1001 stereographic projections. Depending upon whether the crystal axis (i.e., the direction of crystallization) coincides with a <111>, <111>, or <100> direction, the cellular structure viewed from a surface perpendicular to the crystal axis will consist of a network of regular hexagons, skewed hexagons (with interfacial angles of 110" and 125"), or cubes, respectively. It follows, moreover, that off-orientations from these principal directions will yield modifications of these three basic geometric configurations. In this connection, it is interesting to note that the bounding planes of the hexagonal structure observed in tin by Rutter and Chalmers3 showed no preferred orientation.

Jan 1, 1954

By H. H. Otto

Fourteen years ago, J. B. Warriner presented before the Institute a paper on anthracite stripping,&apos; describing the progress of stripping in the Anthracite Region from its beginning with an old quarry stripping at Summit Hill, which was operated more than a century ago, through various types of strippings used in 1917. This paper will briefly review the status of anthracite stripping methods from 1917 to the present day and describe in detail the stripping operation of The Hudson Coal CO. at Clinton collicry. It is not intended as a review of the work in the district—that would require a much longer paper. History and Statistics Mr. Warriner said, in part: "The sizes of shovels have gradually increased until now 70 and 80-ton shovels are the rule and larger equipment is coming in." He also referred to a large electrically operated dragline which weighed about 225 tons and had an operating radius of 125 ft. In 1917, a number of strippings used shovels of various sizes, ranging up to the 60 Marion and Bucyrus 70-C railroad type. Material was hauled away in narrow-gage side dumpers, usually of 4 or 5 cu. yd. capacities. Star-type churn drills with 4-in. bits were generally used for drilling purposes. Since 1917 wages in the anthracite field; have increased, but the higher operating costs of strippings are now being successfully combated by continuous improvements in stripping equipment, such as the development of the caterpillar or crawler shovels, the use of larger cars, better drilling equipment, the introduction of shovels of increased capacity and the adoption, in a number of instances, of standard-gage equipment for transportation. In 1918 another large dragline was introduced in the southern fields, which had been in service in the Middle West and is in use today, dipping vertically about 180 ft. to raise coal out of a stripping. About 1918, small shovels with caterpillar traction were introduced. In 1922 the 6-in. well drills began replacing the 4-in. drills, with an attendant saving to the operators. About the same time A. E. Dick placed the first pair

Jan 1, 1931

By Maurice B. Dusseault, Edo Nyland

Numerous consistent seismic signals are being generated in a pilot fireflood in a 750 m deep high permeability unconsolidated channel sand in Eastern Alberta. The pilot has a central air injection well, eight production wells on artificial lift, and two internally placed observation wells. Surface seismometers and a 12-hydrophone downhole string were deployed to detect seismics signals. Date were collected for 22 hours employing signal-triggered event detectors recording on cassette tapes. Monitoring during twelve hours of steady air injection at 625m3/s yielded a clear event frequency of about 50 events/h. The events were mostly clear compressional wave arrivals originating in the vicinity of the firefront. Stopping air injection caused a gradual drop in event frequency, and the rate was reestablished when air injection was reinitiated. Spectral frequency analysis and knowledge of material properties indicate that the events are shears of a stick-slip nature associated with the strain-weakening behavior of the over-compacted reservoir sands. The event amplitude indicates small-scale shearing, and different amplitudes suggest that planes re-shear with lower energy release levels. The triggering mechanism for shear rupture is high shear stress created by thermal expansion in the area of highest ther- mal gradient. Other enhanced recovery techniques may also produce useful signals for process control. In particular, steam flooding, hydraulic fracturing, and high-pressure injection operations likely generate mappable microseismic events which can be applied directly to production/ injection strategy.

Jan 1, 1982

By T. R. Cass, M. R. Achter

A technique for measuring the creep and rupture strength of nickel specimens bonded by sintered oxide layers has been developed for the investigation of the role of grain-boundary oxide in the oxidation strengthening of nickel during creep at 817 °C. Prom the inverse dependence of the rate of bonding on the thickness of the starting oxide, it is suggested that the rate of diffusion of Ni++ through NiO is the controlling process at the start of sintering. Cornparisons of the creep and rupture strength and of the microstructure of sintered couples with conventionul creep specimens suggest rupture in nickel is prevented by load-bearikzg, ikltergranular layers of oxide. A number of recent investigations have shown that at high temperature and low stress the creep-rupture strength of nickel and nickel-base alloys may be much greater in air than in an inert gas or vacuum.&apos;-7 For example, at 817°C and 2500 psi, nickep failed in vacuum in 48 hr but not in air after 4000 hr, and a Ni-Cr-A1 alloy5 at 1038°C and 3000 psi failed in vacuum in 4 hr but not in air after 731 hr. Fig. 1 is a typical creep curve in air for materials experiencing this pronounced environmental strengthening. A common feature of these curves is the entry into a third stage of accelerating creep, concurrent with the for-

Jan 1, 1962