Search Documents

By Frank Julian

After the solution of an iron ore, or metallic iron, in an acid, for the determination of phosphorus, it is necessary to evaporate the solution to dryness and to heat the residue to effect the complete separation of silica. Authorities differ as to the temperature required, some recormmentling not over 100' C., others as high as dull redness. For the purpose of securing some indications as to the degree of heat which may be safely or advantageously employed, I selected a gray pig-iron, a piece of Bessemer steel rail, and a sample of Ludington ore having the following composition; the phosphorus in the pig and steel being determined by Giutl's ferric chloride method:

Jan 1, 1884

By S. R. Rao

Interaction of potassium amyl xanthate with pyrrhotite has been studied thermochemically. Heats of adsorption of xanthate on unactivated mineral and the mineral activated with cupric ions have been compared with heats of reactions between potassium amyl xanthate and ferrous and cupric salts. It is shown that xanthate is consumed by stoichiometric exchange with anions present at the mineral surface. The floatability of the unactivated mineral is poor since xanthate is precipitated in bulk without creating a hydrophobic surface on the mineral. At the activated mineral surface, xanthate is adsorbed in certain isolated patches (active spots) and thereby creates a hydrophobic surface. The hydrophobicity of the mineral is greatly improved by lowering the pH to 4.5.

Jan 1, 1972

By George W. Healy, Ko Yamaguchi

In typical calorimetry the energy given off by a material under study is transferred to a water bath, whose temperature is sensed by a thermometer; for correct measurement the water bath must attain a uniform temperature to which the thermometer must respond. This introduces two sources of error, non-uniformity of the heat sink and a time lag until its temperature is registered. These errors may become important where a rapid process such as solidification of metals and alloys is being studied by means of Oelsen'sl quantitative thermal analysis. To overcome this difficulty, a calorimeter sink was conceived in which the water bath is replaced by a copper coil, which serves simultaneously as heat

Jan 1, 1967

By K. H. Coats, M. H. Terhune

Analysis and example applications have been performed to compare the accuracy and computing speed of alternating-direction explicit and implicit procedures (ADEP and ADIP) in numerical solution of reservoir fluid flow problems. ADIP yields significantly greater accuracy and requires about 60 per cent more computing time than ADEP, not 300 or 500 per cent more as reported elsewhere. l,2 INTRODUCTION Several recent papers 1-3 discuss an alternating-direction explicit difference approximation (ADEP) to the diffusion equation. Example applications of ADEP and ADIP4 were reported to support conclusions that ADEP is comparable in accuracy to ADIP and requires one-fifth to one-third the computing time of ADIP. Applications of ADEP in calculation of two-phase flow in reservoirs was also proposed. 3 This study was performed to compare further the relative merits of ADEP and ADIP in simulation of two-dimensional flow of one and two fluid phases in reservoirs. Since two-phase flow equations are often essentially elliptic rather than parabolic, the efficiency of ADEP in solving the elliptic equation was also examined.

Jan 1, 1967

By L. Obert, D. E. Stephenson

The objectives of this investigation were to develop a laboratory procedure in which core discing could be produced under known (and variable) stress conditions, and to study the discing characteristics of several fypes of rock. Discing of rock cores refers to the formation of discs or wafers of relatively uniform thickness which fracture or rupture on surfaces approximately *Fracture is a type of failure in which there is a complete loss of cohesion and fresh surfaces are created. Rupture is a type of failure in which there Is only a partial loss of cohesion. normal to the axis to the core (see Fig. 1). Usually the surfaces of the discs are concave-convex with the concave side toward the collar of the hole. The surface of the fractured discs are like those created by a tension failure (or possibly a shear failure with virtually no normal compressive stress). This phenomenon has been observed by a number of investigators1-5 in the course of diamond drilling in underground mines, especially in areas suspected of being under high stress. The state of stress in the core required to produce discing is not exactly known. Tranter and craggs6 theoretically investigated the stress distribution in an infinite cylinder, subjected to hydrostatic pressure, minus p, from z = 0 to z = 8 and unloaded from z = 0 to z = 8, Fig. 2. The exact solution to this problem shows that a tensile stress develops in the loaded region near z = 0 with the greatest tensile stress on the axis of the cylinder. A tensile stress also developed on the surface of the cylinder at a point just outside of the loaded zone. Jaeger and Cook3 experimentally investigated the discing mechanism by biaxially loading cores in a pressure jacket sealed at the ends by O-rings. According to the Tranter and Craggs theory it would be expected that failure should occur at the pressure discontinuity at the O-rings. The experimental results showed that if the specimen was unjacketed it broke at random points within the pressurized zone and at a pressure somewhat greater than the tensile strength of the specimen, presumably due to the development of a

Jan 1, 1965

By Frank Firmstone

IT is often desirable to obtain one or more accurate horizontal sections of a blast furnace after blowing out. Wishing to do this, last April, in the case of No. 4 furnace at Glendon, which had worn in a very remarkable manner, the method described below was employed, with very good results. A scaffold was fixed in the furnace, and on it was placed a drawing- board, covered with paper, the top of which was made level at exactly the height at which the section was to he taken. (Fig. 8.) The centre of the furnace (which had previously been found, and marked on a plank across the top) was laid off on it by dropping a plumb-bob from above, and a strong needle was driven into the board in the centre. By means of a straight-edge and two plumb- bobs, the line passing through the centres of the front and back arches was also drawn on the board. A pencil was fastened to a light wooden straight-edge at a known

Jan 1, 1875

By Frank Firmstone

It is often desirable to obtain one or more accurate horizontal sections of a blast furnace after blowing out. Wishing to do this, last April, in the case of No. 4 furnace at Glendon, which had worn in a very remarkable manner, the method described below was employed, with very good results. A scaffold was fixed in the furnace, and on it was placed a drawingboard, covered with paper, the top of which was made level at exactly the height at which the section was to he taken. (Fig. 8.) The centre of the furnace (which had previously been found, and marked on a plank across the top) was laid off on it by dropping a plumb-bob from above, and a strong needle was driven into the board in the centre. By means of a straight-edge and two plumbbobs, the line passing through the centres of the front and back arches was also drawn on the board. A pencil was fastened to a light wooden straight-edge at a known

By F. X. Tartaron

F. C. Bond (Consulting Engineer, Processing Machinery Dept., Allis-Chalmers Manufacturing Co., Milwaukee, Wis.) — Papers such as this one which deal in a lucid manner with the obscure fundamentals of comminution theory are always welcome. The author has attempted to bring together several diverse theories and handles them interestingly. However, some of the ideas expressed and conclusions drawn require critical reviewing, for which amenities alone will not suffice. The author points out that the theoretical energy required to break across crystal lattices is of the order of 1000 times the actual energy required to crush or grind, and that this energy in turn is perhaps 1000 times the measured surface energy of the new surface area produced. The energy required to grind commercially is controlled by flaws and dislocations, rather than by the inner strength of the lattice structure. The measured surface energy is only a slight residue left after the face atoms are adjusted to their new environment. The dislocations in the crystal lattice structure, with a spacing of about O.l,u, or

Jan 1, 1962

By R. P. Steijn

IT has been observed by a number of investigators that under certain conditions metals freeze into an aggregate of small hexagonal strands, parallel to one another and with their axes approximately in the direction of growth.'" This structure has been termed "cellular structure" and is explained in various ways by different workers, notably by Rutter and Chalmers." These investigators attribute the phenomenon to the presence of minute quantities of solute atoms which induce constitutional supercooling. However, if this is true, observations of the cellular structure in extremely pure substances, like frozen distilled water' and germanium of less than 0.0001 atomic pct metallic solute,' are difficult to comprehend. The purpose of this communication is to describe several observations made of the prismatic structure in zinc of 99.99 pct purity. Zinc single and bicrystals grown in a constant gradient electrical resistance furnace exhibit the cellular structure after etching in 15 pct HC1. (See Figs. 1 and 2.) It is noticed that the hexagonal substructure sometimes continues unbroken across the bicrystalline grain boundary.

Jan 1, 1956

By W. H. Furlonge

WHILE fulfilling professional engagements, my travels over this portion of the Transvaal have been quite extensive—always on horseback however, so that anything like a thorough investigation of the ground passed over has been necessarily impossible; still, the more minute examination of certain small areas, coupled with general observations, has enabled me to form some idea as to the prominent geological features of the country as a whole. Anything like a complete or comprehensive description is indeed out of the question, as there are no proper maps of the country and the facilities for observation are limited. A large plateau, called the "High Veldt," stretches from east to west across the Transvaal. It is generally level, or gently rolling, and has an average elevation of 6000 feet above the sea; it is destitute of timber, and in fact greatly resembles the western prairies of North America. Rock-outcrops are not common in it. It terminates very abruptly to the east and northeast, the descent of 2000 or 3000 feet into the mountainous country that occupies its borders being made in a

Jan 1, 1890

By G. D. Cremer, J. J. Cordiano

Aluminum powder is a well-known article of commerce and in various forms has been marketed widely for use in paint, for pyrotechnic purposes and for exothermic mixtures. For a number of reasons, however, aluminum powder has not been employed extensively in powder metallurgy, although a great many proposals along this line have been offered. Aluminum and alumiuum-alloy powders oxidize readily upon exposure to air and the thin film of oxide (or hydroxide) thus formed is highly refractory, in that ordinary gaseous reducing agents such as hydrogen or carbon monoxide do not reduce the oxide to metal at temperatures below the melting point of aluminum. It has been thought that the presence of these films of oxide on aluminum particles would interfere markedly in powder metallurgical work and a number of suggestions have been made, either for preventing the formation of the film through the production of the powders in inert or reducing atmospheres, or for the removal of the oxide by means of powerful reducing agents, including "nascent" or atomic hydrogen released from metal hydrides. A second and more serious difficulty in the use of aluminum and aluminum-alloy powders in powder metallurgy resides in the fact that during compression such powders tend to adhere or cold-weld to the die walls, thus interfering with the formation and ejection of a compact. A third difficulty, which has been encountered only with aluminum-alloy powders, is their hardness when compared with elemental aluminum. Certain of these powders are susceptible to age-hardening, which further hinders the formation of strong green compacts. These conditions are particularly true of atomized aluminum-alloy powders. Even in the annealed condition, plastic deformation of alloy powders under pressure is low when compared with unalloyed powders. This fact, coupled with the lower corrosion resistance of the alloy powders. is probably the significant factor in our failure to obtain strong sintered pieces. Methods of Puoducing the Powder Many methods have been proposed for manufacture of aluminum powder, only a few of which are used commercially. Several of the more important processes include: (I) atomization of the molten metal; (2) mechanical pulverization and other types of comminution; and (3) graining, in which molten aluminum is stirred during freezing. For pigment and certain pyrotechnic uses aluminum flake powder is desirable, because of its greater proportion of surface to volume; and large quantities of such material are made by a procedure that involves stamping or ball milling. In making flake intended for use as pigment,

Jan 1, 1943

By G. D. Cremer, J. J. Cordiano

Aluminum powder is a well-known article of commerce and in various forms has been marketed widely for use in paint, for pyrotechnic purposes and for exothermic mixtures. For a number of reasons, however, aluminum powder has not been employed extensively in powder metallurgy, although a great many proposals along this line have been offered. Aluminum and alumiuum-alloy powders oxidize readily upon exposure to air and the thin film of oxide (or hydroxide) thus formed is highly refractory, in that ordinary gaseous reducing agents such as hydrogen or carbon monoxide do not reduce the oxide to metal at temperatures below the melting point of aluminum. It has been thought that the presence of these films of oxide on aluminum particles would interfere markedly in powder metallurgical work and a number of suggestions have been made, either for preventing the formation of the film through the production of the powders in inert or reducing atmospheres, or for the removal of the oxide by means of powerful reducing agents, including "nascent" or atomic hydrogen released from metal hydrides. A second and more serious difficulty in the use of aluminum and aluminum-alloy powders in powder metallurgy resides in the fact that during compression such powders tend to adhere or cold-weld to the die walls, thus interfering with the formation and ejection of a compact. A third difficulty, which has been encountered only with aluminum-alloy powders, is their hardness when compared with elemental aluminum. Certain of these powders are susceptible to age-hardening, which further hinders the formation of strong green compacts. These conditions are particularly true of atomized aluminum-alloy powders. Even in the annealed condition, plastic deformation of alloy powders under pressure is low when compared with unalloyed powders. This fact, coupled with the lower corrosion resistance of the alloy powders. is probably the significant factor in our failure to obtain strong sintered pieces. Methods of Puoducing the Powder Many methods have been proposed for manufacture of aluminum powder, only a few of which are used commercially. Several of the more important processes include: (I) atomization of the molten metal; (2) mechanical pulverization and other types of comminution; and (3) graining, in which molten aluminum is stirred during freezing. For pigment and certain pyrotechnic uses aluminum flake powder is desirable, because of its greater proportion of surface to volume; and large quantities of such material are made by a procedure that involves stamping or ball milling. In making flake intended for use as pigment,

Jan 1, 1943

By I. W. L. Finlay, H. R. Ogden, R. Jaffee, D. J. Maykuth

Aluminum has been found to be soluble in a titanium to about 26 pct, and to raise the temperature range of transformation from a to 8. Two intermediate phoses exist in the system, a new face-centered tetragonal phase, designated as 7, which occurs between 34 and 46 pct Al, and TiAI Metallographic and X-ray diffraction data were used to determine the diagram. ALUMINUM is one of the useful alloying additions for titanium-base alloys. It is an important constituent in two commercial alloys released in 1950, one containing 4 pct A1 and 4 pct Mn, and the other containing 3 pct A1 and 5 pct Cr as the metallic alloy content. It is probable that, in the future, other titanium alloys containing aluminum will be released. In the course of alloy development work, some of the features of the constitution of titanium-rich Ti-A1 alloys have been developed. These are described in the present paper. The only available information on the Ti-A1 system concerns the aluminum-rich end of the diagram. In summarizing the early work, Hansen' indicated that there is little solubility of titanium in aluminum, and that a two-phase region exists up to the intermediate compound, TiA1a (37.2 wt pct Ti), which has a congruent melting point at 1355°C. Fink' has reported that a peritectic reaction occurs at 665°C between the melt and TiA1³ to form the terminal solid solution of titanium in aluminum. The solubility of titanium in aluminum has been established at 0.24 pct at 510°C and is estimated to be between 1 and 1.5 pct at the peritectic temperature. No information has been published on the diagram above TiAl,, other than a statement- hat aluminum raises the a to ß transformation temperature of titanium. Materials and Preparation of Alloys Iodide-type titanium and high-purity aluminum were used in this investigation. Typical analyses of these materials are given in Table 1. Alloys were prepared by arc melting on a water-cooled copper hearth, using the techniques described previously for contamination-free melting.' Weight losses during melting were very low, ranging from 0 to 0.02 g in a 10 to 15 g charge, indicating that little or no loss of aluminum occurred during melting. This permitted the use of nominal compositions for these alloys. Alloy ingots containing from 0 to 7.5 pct A1 were rolled in air at 850°C to 0.040 in. sheet. Alloys containing from 7.5 to 16 pct A1 could only be rolled about 25 pct reduction at temperatures up to and including 1200°C. Alloys containing above 16 pct A1

Jan 1, 1952

By Henry N. McCarl

[The Construction Materials section contains the following Chapters: Aggregates Cement and Cement Raw Materials Crushed Stone Dimension and Cut Stone Lightweight Aggregates Gypsum and Anhydrite Sand and Gravel Insulating Materials-Thermal and Sound Slag Roofing Granules] Mineral aggregates are those natural and manufactured industrial mineral and rock materials that provide bulk and strength in portland cement concrete, bituminous concrete mixes, and plaster or stucco surfaces. They may also provide special characteristics such as thermal and acoustical insulation, weight, surface textures, abrasion resistance, and impermeability to various concrete products and mixes. Most aggregates are relatively inexpensive materials, but despite their low unit value, the tonnages consumed each year in the United States and throughout the" world make mineral aggregates by far the leading industrial mineral and rock materials both in terms of volume (tonnage) produced and value consumed. The major use of mineral aggregates is in concrete. The low cost, high bulk aggregates tend to keep concrete construction costs at levels competitive with other building materials. Other major uses of aggregates include highway and railroad base or ballast materials, graded fill, and various industrial uses such as metallurgical and chemical fluxes and raw materials-these latter uses are often considered nonaggregate uses of mineral aggregate materials. The per-ton value of mineral aggregate materials at the production plant in 1980 and 1981 varied from $2 to $5 for most sand and gravel and crushed stone, $3 to $6 for air-cooled slag, $7 to $20 for expanded slag and expanded clay or shale aggregate, to as much as $165 to $320 for expanded perlite or vermiculite. The expanded lightweight aggregates have been dramatically affected by increasing fuel costs. It is ironic that the specialized aggregates used as insulating materials to conserve energy cost so much more to produce due to the high proportion of energy consumed in their production. The first four parts of "Construction Materials" deal with the utilization of four major mineral aggregate types: Crushed Stone, Lightweight Aggregates, Sand and Gravel, and Slag. While the focus will be on the use of these industrial minerals and rocks, there will also be some coverage of sources, mining and production, especially in those cases where they are not discussed in the Commodity section of this book.

Jan 1, 1983

By L. A. Willey

Although the interierometric method for the determination of length changes was devised by Fizeau more than three quarters of a century ago, it has not achieved the widespread use in the metallurgical field that its precision and simplicity would seem to warrant. The interferometer and the basic principle are both very simple. When optically plane surfaces held at a very slight angle to each other are illuminated by monochromatic light, rectilinear, equally spaced interference fringes arc formed. Each fringe corresponds to a defiuitc thikness of the wedge formed by the optical flat.;. The difference in wedge thickness between two consecutive fringes is cqual to one half the wave length of the illuminating light. Instruments for vicwing the intertero~ncter have passed through a number of modifications. Outstanding among the improvements were those Abbe. in 1884. His improved instrument permitted micrometric mcasurements to the order of one-hundredth of the width of an interference fringe (i.e., lengths were measured to the order of one two-hulldredth of the mave length of light ). It also permitted the consecutive use of light of several wave lengths. which made possible the determination of the order number of any fringe and therefore the absolute thickness of the wedge at any point. The Abbe dilatometer and methods of measuretment, including corrections to he applied for the change of index of refraction with change in tempcrature and barometric pressure in an air wedge, have been thoroughly described by Pulfrich.' Pulfrich2 made further improvements in the interference measuring apparatus. His instrument embodied all the features of the Abbe dilatometer but was made more versatile by its complete mechanical separation from the interferorneter. The introduction of an Amici prism in the piece permitted the simultaneous observ tion of the whole set of fringe systems developed in the interferometer from the visible light of a geisler tulle. .Also, the introduction of a direct-vision, reflecting prism made it possible to set the fringes parallel to the two vertical fiducial line. of the instrument without the necessity of rotating the interierometcr. Interferometric methods employed ill this country have been developed and dcscribed by Priest, Pelers and Cragoe," Austin,5 Merritt,= Saunders,? and Nix and MaNair. Since none of these authors used the type of instrument that was employed in the present investigation, they Will not be discussed here. This paper will be limited to the description of the interfernmetric apparatus and method used at the Aluminum Research Laboratories and to the presentation of data so obtained. Apparatus and Procedure A general view of the dilatometer, not including equipment for controlling and

Jan 1, 1945

By F. C. Sturges

[CONTENTS PAGE ................. Introduction-Grouting in Mines. By F. C. STURGES. I Use and Technique of Pressure Grouting in the Construction Industry. By V. L. MINEAR . 3 Technique of Pressure Cementing in the Petroleum, Mining, and Construction Industries. By WY. D. OWSLEY and R. E. MOELLER. ..................... 9 An Example of Controlled Pre-grouting in Shaft Sinking. By R. H. ALLEN and J. W. GALPIN. 15 ........ Solidifying Mines and Shafts Areas by Pressure Grouting. By B. H. MOTT 17 .............. Grouting in Southeast Missouri District. By W. W. WEIGEL 20] Introduction-Grouting in Mines By definition the word "grout" means a thin mortar, or a kind of plaster or cement, and "grouting" means to fill up or finish with grout. The words "cement," "plaster" and "mortar" mean a substance that is used in a soft state which subsequently hardens. Thus, grouting is the filling of void space with a substance that hardens. Construction cements are the most common substances used, either by themselves or in mixtures, but the term grouting is applied quite correctly when other substances such as plastics and certain chemicals are used. Also, the use of the term grouting to cover the filling of voids with materials that do not actually become hard, such as the flotation tailings used in grouting in the southeast Missouri lead district, should be considered correct, as some stiffening does take place and, anyway, it is a better descriptive term than any substitute. Engineers are interested in grouting because some of the materials with which they must work contain voids, and certain conditions can be improved if these voids can be filled with something solid and permanent. Grouting is done to accomplish several purposes: I. To stop the passage of fluids and gases, 2. To cement materials together to make them stronger, and 3. To prevent consolidation of materials by filling void space with something solid as a replacement for the air and water that could be forced out under load. The construction industry uses grouting extensively for all three purposes. Grouting is used to stop water percolation under and around dams. It is used to control water flow in tunnel driving and in shaft sinking. It is used to improve foundation conditions under civil engineering structures by permanently filling void space and thereby reducing settlement, or by cementing broken rock together and increasing its supporting strength. The oil and gas industry does a lot of grouting, primarily to stop the passage of gases and fluids. The search for oil at increasingly greater depths has meant greater investment per well, and the oil industry has spent large sums on development of improved drilling methods. This

Jan 1, 1947

By Noel Stearn

WHEN the Age of Machinery was suddenly thrust upon civilization about the beginning of the nineteenth century, an unprecedented demand for mineral resources sprang up. This demand brought about the rapid development of the known ore deposits and the discovery of such other deposits as could be encountered by energetic and canny pros-pectors. Thus in the countries now reasonably ac-cessible nearly all orebodies have been located except those which are totally concealed even from the eyes and "senses" of experienced and expert prospectors. The high rate of exhaustion of known ore deposits and the necessity of looking farther and farther ahead for raw materials as a matter of insurance on the stu-pendous capital outlays involved in mining, develop-ment, and conversion operations, have resulted in excep-tional activity in three different fields of effort. The first is purely geographic. Prospectors are now pene-trating the few hitherto inaccessible regions in the hope of stumbling upon exposed ore deposits or locating visible indications of their presence. The second is chemical. Industrial chemists and metallurgists are seeking to facilitate the exploitation of lower grade ores to find methods of recovering valuable metals from common substances. In the third field of effort. lie the activities of the economic geologist and the mining engineer, who en-deavor to locate concealed ore deposits, which would remain hidden from the prospector, no matter. how expert or conscientious he might be. Obviously the task which such a man must face is both exacting and indefinite, and the tools which he has heretofore been permitted to bring to it are, for the most part, abstract-a knowledge of certain fundamental princi-ples and processes involved in the origin, occurrence, structure, and distribution of deposits. of natural re-sources and of the rocks which form the environments of those deposits, and a process-of reasoning by analogy supplemented by the .use of the diamond drill, or such artificial exposure as the test pit, trench, shaft or tunnel. His primary efforts are usually bent on acquiring a knowledge of the distribution of the rocks-as accurate -is possible-which is a natural prerequisite to any conclusion as to how they became so distributed. Over very extensive areas, however, he meets. the extreme difficulty of being unable to see the rocks, except at rare intervals, since .they have been concealed by an overburden of glacial material, of alluvium, of soil, or of other rocks.

Jan 9, 1928

AN intermetallic compound, Ni3A1, has an ordered fcc structure of type Ll2, and shows peculiar dependence of the yield stress upon temperature; i.e., the yield stress increases by a factor of six upon raising the temperature from 77" to 900K1, 2 This compound is technologically important, since many nickel-base superalloys owe their high-temperature strength to the peculiar yield stress behavior of Ni3Al. The only study of the elastic behavior of this compound was made by Davies and Stoloff,1 who determined Young's modulus of poly crystalline Ni3A1 between 300" and 730°K. The determination of single-crystal elastic constants of Ni3A1 is therefore of interest in connection with dislocation dynamics and is reported in this paper. A single-crystal specimen, 1 by 1 by 3 cm, was cut from an ingot generously supplied by Dr. B. H. Kear of Pratt & Whitney Aircraft. Following initial machining with a Servomet and a surface grinder, the specimen was etched and annealed at 1100°C for 5 hr in vacuum followed by furnace cooling. Two parallel faces were oriented normal to within ±l deg of a [I101 crystallographic axis by the back-reflection Laue technique. The parallel faces were hand-lapped, etched, and polished by the usual metallographic procedures. Final thickness along the [I101 axis was (0.9325 * 0.0005) cm. Chemical analysis gave an average composition of 87.35 pct Ni. Total impurity content is esimated to be no more than 0.1 pct. The elastic constants were calculated from measurements of ultrasonic waves which were propagated along the [110] axis. A longitudinal wave and two shear waves whose displacements are aligned along the [ 110], [li~], and [001] directions, respectively, are necessary in order to completely specify the three elastic constants. Two 3/6-in. quartz transducers were bonded to the parallel faces of the sample with ~ac-seal.3 Although this bond was sensitive to thermal shock, it performed satisfactorily over the entire temperature range for both longitudinal and shear wave propagation. A frequency of 5 mHz was employed in the method of Williams and Lamb4 in order to measure the absolute value of the ultrasonic velocity. The pulse-overlap technique of Mcskimin5 was also used at this frequency in order to determine the shift in the ultrasonic velocity

Jan 1, 1970

By L. G. Austin

My first contact with industrial milling was during the time I worked in the electricity generating industry in the United Kingdom. In visits to power stations to investigate either deposits in the boiler furnaces or polluting deposits settling around the stacks. I had to check the performance of the vertical coal pulverizers, since poor pulverization aggravated both problems. Naturally, then, when I came to the USA in 1957 to take a PhD in fuel technology at Penn State, I was put to work to review the science of coal pulverization. After this reviewing, I was completely confused. On one hand, there was a well-developed understanding of stress-strain equations, and a rapidly developing knowledge of how stressed, brittle solids fractured, based on the Grifith crack theory. On the other hand, reading in the grinding literature gave me: -Kick's Law, which was clearly not correct in the light of modem fracture theory; -Rittinger's Law, which was also clearly not correct; -Bond's Third Law of Comminution, which was claimed to have something to do with the Grifith crack theory, but where the connection between the two was made by intuitive pseudo-scientific reasoning I could not accept; -the choice of mill motor power for the most common type of coal mill, the Raymond pulverizer, was calculated from the fan power required to move air through the mill. Although I could accept the empirical connection between the two, it made no sense from the point of view of fracture energy. Even today, most books or review chapters on size reduction start from these laws. Incorrect statements abound in the literature, such as "the Hardgrove Index is based on Rittinger's Law," which it is not, "The Bond theory states that work input is proportional to new crack tip length produced in particle breakage," which is not true, etc. My own test work showed that these "laws" did not fit the data for grinding of coal. At about this time, Epstein (1948) and Broadbent and Callcott (1956), following the original work by R.L. Brown (1941) at the British Coal Utilization Research Association, proposed describing breakage as a series of fracture stages. I took their concepts and developed the basic differential equation for a batch grinding process continuous in time, analogous to a batch chemical reactor. Robin Gardner then joined the project and did his PhD on treating batch grinding in the same way as a batch chemical reactor. He found that the basic equation had already been partially derived by Sedlatschek and Bass (1953) in Ger- many. We confirmed experimentally the validity of the equations for describing batch grinding (1962) and formulated the equation describing steady-state continuous grinding in a fully-mixed mill. At about the time this work was published, Gaudin and Meloy (1962) and Filippov (1961) independently published essentially the same equations, but without experimental proof of the validity of the concepts. I will give a brief overview of what these beginnings had led to in the design of mills for size and power, and show some of the results of this more detailed understanding of grinding processes. Concepts of Fracture Mills such as tumbling ball, rod, pebble and autogenous mills and vertical mills such as the Raymond, and E-type, apply compressive stress to lumps or particles relatively slowly. Compressive stress applied to a particle of an elastic brittle solid imparts overall strain energy to the solid and produces local regions of tensile stress, [(Fig. 1)] (Berenbaum and Brodie, 1959).

Jan 1, 1985

By E. G. De Coriolis

The development of huge production facilities and of new or improved processes for manufacturing magnesium from its raw sources has been an outstanding achievement of this war. Furthermore, at least one new method has reached a stage of pilot production that offers promise. Its potentialities seem to indicate that a reduction in cost and simplification or elimination of problems incident to the use of at least one of the present processes are quite within the realm of possibility. Although magnesium of very high purity (99.9 per cent and higher) is obtained, and the rate of recovery reasonable (60 to 70 per cent). the ferrosilicon reduction process is open to a serious objection, which at the time its use was proposed was thought to be sufficient to raise some doubts as to its success, at least on a high production basis. The temperature range at which the reaction is carried out—namely, 2100" to 2150°F.—is very close to the failure temperature of the material of which the retort is made. It is so close that for a time it was assumed it might make commercial use of the process an impossibility. However, at the time under discussion, the demand for magnesium was so great that it was felt by those who had to go ahead and produce this essential metal that the emergency warranted their taking a chance on this process. Subsequent developments have fully justified the soundness of their decision. Fortunately for the war effort, when the plants were put into operation it was discovered that although the retorts did collapse in rather short periods of time, as predicted, they could be blown back into operable shape by application of high-pressure air. This practical method of operation so relieved the situation that the problem disappeared. Nevertheless, if the process had not been successful, or the production of magnesium by the electrolytic process had not been able to keep pace with demands, our war program would have been seriously impaired. Fireless Cooker'' Process For this reason a program was set up and assigned for the development of a new method that had been suggested to the War Production Board in 1941. It is believed justifiable in terming the method "new" for several reasons: (I) while utilizing the same (ferrosilicon) process as the Pidgeon, hence involving similar reactions, the type of retort or furnace is essentially different, (2) the method of operation, reaction temperatures, etc., differ materially, and, most important of all, (3) the problems to be overcome in making the process successful were not and could not have been anticipated by anything previously known about the Pidgcon process. As will be shown later, the briquetting process, the condenser, the furnace lining

Jan 1, 1949