Search Documents

By P. A. E. Armstrong

For hardening, the steel should be heated just above the critical temperature, as a properly forged steel quenched from this heat has some toughness, with maximum hardness and density. The quenching bath should be kept at approximately a constant temperature. In drawing or tempering, longer time periods at lower temperatures are better than the shorter periods at higher temperatures. A recent questionnaire brought out the following facts: The double-arc, double-taper bit and cross bit give the best service; resharpening of the drill steels most frequently was caused by wear of gage; chipping of bit was, with one exception, the second cause; breakage of shank was with one exception, the third cause; upsetting of bit, upsetting of shank, and breakage of body were the fourth cause. The direct cause of the necessity of resharpening given was poor heat treatment first, and faulty steel and severe rock conditions second. Rock-drill Steel By N. B. Hoffman Much of the drill steel produced in America is manufactured into hollow rods. After all forging has been finished the entire bar should be thoroughly annealed and heat trcated before the point is hardened and tempered, at least where the drill has heavy duty, such as working in deep holes and hard rock. A large number of tools of like character and doing work requiring similar properties are now being made of alloy steels; for instance a steel with a carbon content of 0.75 to 0.85 per cent., manganese 0.25 to 0.35, phosphorus under 0.020, sulfur under 0.030 and vanadium 0.18 to 0.23 has proved very satisfactory for chisels. A steel of this type properly manufactured will be far superior to the ordinary carbon steels, while at the same time is one whose price range should not prove prohibitive. Much of the cutting efficiency of a drill depends on proper heat treatment. This vanadium steel has a far greater safe hardening and forging range than ordinary carbon steels, making it more nearly foolproof. It will harden nicely at 1400" I?. but will also harden well and satisfactorily at 1550" F. retaining its quality of hardness and toughness in either case. Drill Steel from Hollow Ingots BY P. A. E. ARmstrong Hollow drill steel is made from a drilled billet with a sand-filled core or the drilled, pierced, or the drilled and pierced billet, not sand-filled, is rolled down over a projectile or ball much the same as in ordinary pipe manufacture. The first is the method generally used in this country; the second is used largely in Sweden. Swedish hollow drill steel has a

Jan 1, 1922

By D. K. Deardorff, Haruo Kato

D. K. Deardorff and Haruo Kato (U. S. Bureau of Mines)—We wish to refute the 1875" 20°C value that Giessen, et al., report as the transformation temperature of hafnium. Although these authors state that their work along this line will be reported later, we can't leave their value undiscussed, for we believe it to be 125°C too high. Our value of 1750° 20°C, which the authors mention, has been substantiated in our laboratories by the use of three other methods. The first method of substantiation was by heating and cooling curves using a hafnium/tungsten thermocouple, the couple having first been calibrated against a t/Pt-10 pct Rh couple. The second method was by quenching and metallography of dilute Hf-Ta alloys. The third cussion, it may be pointed out that the observations of Rogers referred to large unidirectional strains where the internal cracks or voids appeared only after a strain of 32 pct or more. On the contrary the internal fissures observed, as a result of fatigue cycling, occurred for a total extension of some 5 pct and furthermore followed the directions of the slip zones. Finally, it is not our contention, as implied in Dr. Alden's last paragraph, that the tensile stress is an important factor in crack propagation. Indeed, in connection with the reference to the companion report, special note is made of the fact that "Deformation was apparently concentrated in grains which have a slip plane nearly perpendicular to the specimen axis and thus near the plane of maximum applied shear." This dependence of the growth of fissures on the orientation of the slip planes with respect to the direction of maximum applied shear is clearly shown in work on the torsional cycling of single crystals which has been submitted for publication. method was by heating and cooling curves with W/W-26 pct Re thermocouple. Counting the original resistometric method, four different methods have yielded 1750" 20°C as the transformation temperature of hafnium. All our work on determination of the hafnium transformation temperature has shown that the specimen under test must be quickly heated to and through the transformation temperature if the lowest possible transformation value is to be determined; otherwise a higher value not representative of pure hafnium will result. Speed was emphasized in all methods. In our resistometric work the corresponding voltage, amperage, and temperature readings were taken quickly and the transformation temperature was usually reached within 5 min total heating time. In the thermal analysis work involving Hf/W or W/W-26 pct Re thermocouples the transformation temperature was attained within three minutes total heating time, this time being less because the two variables were

Jan 1, 1963

By C. S. Barrett, D. F. Clifton

THE transformation that occurs in lithium and its solid solutions containing magnesium1,2 is similar in many respects to other diffusionless transformations of the martensitic type. This general similarity makes it desirable to investigate the transformation curves in detail. The current interest in the phenomenon of stabilization in martensitic transformations has created a need for a careful appraisal of possible stabilization effects in both cooling and heating transformations in lithium alloys. The effect of prior heat treatment on the temperature at which transformation begins and the effect of various temperature cycles in partially transformed alloys also merit attention. Limited data on some of these features were presented previously,' but the present studies have been made with improved apparatus, in which erratic fluctuations were smaller than in the earlier work, and include many independent determinations of certain critical observations. Material and Methods Geiger counter X-ray spectrometers were used: a Norelco instrument, original model, and a General Electric XRD-3. The low-temperature specimen holder has been described elsewhere." Specimens 10 mm in diam and 1.5 mm thick were held in firm contact with a copper block which was attached to the lower end of a stainless steel tube that extended up to a reservoir of liquid nitrogen. A heating coil on the tube permitted a controlled temperature gradient along the tube, so that desired temperatures and rates of heating and cooling could be obtained by controlling the heating current. The specimen was surrounded by an atmosphere of evaporated nitrogen in an insulated chamber having double cellophane windows. The temperature of the specimen was read by a thermocouple imbedded in it close to the irradiated area; the specimen could be held at constant temperature within 1°C for long periods. The body-centered cubic 200 reflection near 8 = 26" was used as the index of the amount of b.c.c. material present; occasional checks were made using the most suitable line of the low-temperature phase, the close-packed hexagonal 110 line near 8 = 29". Copper radiation was used throughout. A continuous record was made of the reflected intensities on a strip chart recorder, both when the peak intensity of a line was being followed and when the lines were being scanned at constant temperature. On the continuous recordings of peak intensity, periodic checks were made on the background intensity between the lines, and on the setting of the spectrometer for maximum intensity. The lithium-base solid solution containing 12.4 atomic pct Mg (33.3 wt pct) that had been used previously' was chosen, as it had a transformation range at relatively high temperatures, so as to permit wide temperature cycling within the range. Just prior to use a pellet was cut from the ingot,

Jan 1, 1951

By V. S. Tuman

In the first part of this paper, an estimate is made of the magnitude and extent of the thermal stresses which result from mud circulation. Our study is made for the period of relaxation, i.e., when the drilling operations are terminated and mud circulation is discontinued. In the second part, we have shown how the thermal stress can affect the wave propagation. An example is worked out for a Carbondale sandstone (Illinois basin). It is concluded that, in extreme cases when differential temperature is about 100°F, the travel time will be affected by about 2 microsec/ft. For more refined permeability studies, such corrections would be desirable. MAGNITUDE AND EXTENT OF THERMAL STRESSES RESULTING FROM MUD CIRCULATION When geological beds are penetrated by boreholes, it is observed that the formation temperatures increase with depth; however, the temperature profile varies considerably from place to place. During drilling operations, mud pumped from a pit at atmospheric temperature absorbs heat from the lower beds. As a result, the drilling fluid returning to the surface is at a higher temperature than the surrounding beds. The temperature gradient in a well depends on the rate of mud circulation and other factors; normally, this temperature gradient is smaller than the natural gradient in the formations. (See Fig. 1.) The temperature difference between the mud column and the surrounding beds gives rise to therma1 stresses (which are also important in the phenomenon of fracturing), and it is expected that they will affect the transit time of the sonic front in velocity logging.1 It is evident chat beds near the surface will undergo various cycles and will have a complicated dynamical and thermal-stress history. A limestone bed which is just penetrated will act as a source of heat, warming up the cold mud pumped down a few minutes earlier from the surface pit. The same limestone bed a week later will act as a sink, absorbing heat from the drilling mud which has already warmed up sufficiently to be at a higher temperature than the bed in question. No doubt a large section of the hole will undergo a heat treatment, which will make the calculation of the exact magnitude of the thermal stresses very difficult. In the solution of wellbore thermal equation, it is assumed that the rock around the wellbore is elastic and isotropic, and that the system is radially symmetrical. A complete dynamical solution of the thermal stresses set up at different horizons during the drilling operations would require a comprehensive history of the mud circulation, the surface temperature of the pit and the number of hours in which mud was not circulated. CONDUCTION OF HEAT AND THERMAL EQUATION OF STATE

By Robert I. Jaffee, Bruce W. Gonser, Eugene M. Smith

There has been little investigation of the gold-germanium binary alloys. Haughtonl does not mention any work on the system. In a review article commemorating the fiftieth anniversary of the discovery of germanium, E. Einecke2 mentioned a gold-germanium eutectic at 24 atomic per cent Ge (10.4 weight per cent) melting at 359°C., but did not give the source of his information. From measurements of electrical conductivity, J. 0. Linde3 estimated that at least 0.6 weight per cent germanium is soluble in gold. The recent availability of germanium in this country in commercial quantities has led to interest in its properties and its alloys. This study is part of a program of investigation on germanium alloys; work on ternary alloys involving germanium and gold will be reported later. In this investigation, the composition and melting point of the Au-Ge eutectic reported by Einecke has been found to be substantially correct. Eutectic composition has been placed at I2.0 per cent germanium, however. An alloy of 10.4 per cent Ge, Einecke's value, was found to have a few gold dendrites in it. The cutectic temperature has been determined as 356.0 6 ± 0.5°C., slightly less than the temperature of 359°C. reported by Einecke. The liquidus curves and the solid solubility of ger- manium in gold have been determined, and are shown in Fig. I. Materials and Alloying The germanium used in this investigation was prepared by the Eagle-Picher Lead Co. from pure germanium oxide, by reduction in clay crucibles with sodium cyanide. The regulus is quite pure, assaying over 99.9 per cent Ge. High-purity gold obtained from Handy and Harmon was used. Alloying was carried out in graphite crucibles in an atmosphere of purified hydrogen. The temperature was brought up to 1050" to iioo°C., and the metal was allowed to freeze in the crucible. Prepared in this way, the gold dendrites in hypoeutectic alloys were somewhat segregated at the bottom and sides of the ingot, and on the hyper-eutectic side the lighter primary germanium tended to gather at the top. Most of the alloys were made from virgin metal. Low-germanium heats were made by alloying pure gold with the eutectic. Melting losses were consistently a few milligrams or less, and the composition could safely be taken from the intended analysis. The 30 per cent and 50 per cent germanium heats for thermal analysis were made in part from remelted higher germanium heats, and they may be OR composition as much as one per cent. Because of the high cost of materials, the weight of heats for thermal analysis were 15 to 20 grams and heats for metallo-graphic, X-ray, and hardness specimens were 2 to 4 grams.

Jan 1, 1945

By Robert I. Jaffee, Bruce W. Gonser, Eugene M. Smith

THERE has been little investigation of the gold-germanium binary alloys. Haughton1 does not mention any work on the system. In a review article commemorating the fiftieth anniversary of the discovery of germanium, E. Einecke2 mentioned a gold germanium eutectic at 24 atomic per cent Ge (10.4 weight per cent) melting at 359°C., but did not give the source of his information. From measurements of electrical conductivity, J. 0. Linde3 estimated that at least o.6 weight per cent germanium is soluble in gold. The recent availability of germanium in this country in commercial quantities has led to interest in its properties and its alloys. This study is part of a program of investigation on germanium alloys; work on ternary alloys involving germanium and gold will be reported later. In this investigation, the composition and melting point of the Au-Ge eutectic reported by Einecke has been found to be substantially correct. Eutectic composition has been placed at 12,0 per cent germanium, however. An alloy of 10.4 per cent Ge, Einecke's value, was found to have a few gold dendrites in it. The eutectic temperature has been determined as 356.0 ± 0.5°C., slightly less than the temperature of 359°C reported by Einecke. The liquidus curves and the solid solubility of germanium in gold have been determined, and are shown in Fig. I. MATERIALS AND ALLOYING The germanium used in this investigation was prepared by the Eagle-Picher Lead Co. from pure germanium oxide, by reduction in clay crucibles with sodium cyanide. The regulus is quite pure, assaying over 99.9 per cent Ge. High-purity gold obtained from Handy and Harmon was used. Alloying was carried out in graphite crucibles in an atmosphere of purified hydrogen. The temperature was brought up to 1050° to 1100°C., and the metal was allowed to freeze in the crucible. Prepared in this way, the gold dendrites in hypoeutectic alloys were somewhat segregated at the bottom and sides of the ingot, and on the hypereutectic side the lighter primary germanium tended to gather at the top. Most of the alloys were made from virgin metal. Low-germanium heats were made by alloying pure gold with the eutectic. Melting losses were consistently a few milligrams or less, and the composition could safely be taken from the intended analysis. The 30 per cent and 50 per cent germanium heats for thermal analysis were made in part from remelted higher germanium heats, and they may be off composition as much as one per cent. Because of the high cost of materials, the weight of heats for thermal analysis were 15 to 20 grams and heats for metallographic, X-ray, and hardness specimens were 2 to 4 grams.

Jan 1, 1945

By H. C. Fiedler

The solubility of sulfur in Si-Fe was determined by the metallographic examination of heat-treated and quenched samples. In the absence of manganese, the solubility in 3.1 pct Si-Fe was found to be about 0.010 pct at 1000o C, 0.015 pct at 11000C, and 0.020 pct at 1150°C, which is substatntially less than hitherto reported. Increasing the silicon content was found to decrease the solubility of sulfur, which is consistent with the increase in the activity coefficient of sulfur with increasing silicon content that has been reported for Fe-Si alloys. Manganese additions were studied in alloys containing 3.1 pct Si and between 0.013 and 0.015 pct S. At low manganese levels the solubility product of manganese sulfide was found to be lower than previously reported. THE solubility of sulfur in pure polycrystalline iron has been reported by Rosenquist and Dunicz1 and by Turkdogan et al.2 Samples were equilibrated in atmospheres containing different ratios of H2S/H2. Both groups of investigators found a solubility limit in y iron of 0.013 pct at 1000oC and 0.031 pct at 1200°C. In addition, Rosenquist and Dunicz1 found a solubility limit in a iron of 0.020 pct at 900°C. Ainslie, Hoffman, and seybolt3 found significantly higher sulfur contents in polycrystalline iron samples than in single-crystal samples after heating at 890°C in a sealed tube containing a mixture of powdered iron and FeS made with s35. Whereas the single crystals contained 0.013 and 0.016 pct S (± 0.005 pct), the polycrystalline samples contained between 0.016 and 0.026 pct S. Autoradiographs suggested that the excess sulfur in the polycrystalline samples was due to the segregation of sulfur in solution at grain boundaries. Ainslie and seybolt4 have reported on the solubility of sulfur in 3 pct Si-Fe. Their samples were sealed in capsules containing hydrogen and sufficient sulfur as cobalt sulfide to saturate the sample. After heat treating, the sulfur-rich phase on the surface was removed by abrading, and the sulfur content of the sample was taken as the equilibrium value for that temperature. Before the equilibrating heat treatment, the samples were heated to 1300°C to coarsen the grains. The resulting grain size, which was about 3/18 in. in diam, was considered sufficiently large to preclude a sensible increase in sulfur solubility due to grain boundary segregation. They reported the solubility to be 0.029 pct at 900oC, 0.063 pct at 1000oC, 0.076 pct at 1100°C, 0.122 pct at 1200°C, and 0.098 pct at 1300°C.

Jan 1, 1968

By John L. Ham, Robert M. Parke

THE melting point of molybdenum is 2625° ± 50°C. Heretofore the metal has been considered too refractory to be melted in commercial quantities; hence, it has been formed into rod, wire, and sheet by the methods of powder metallurgy, wherein the temperatures do not exceed 90 per cent of the melting temperature. The manipulation of liquid metals at temperatures of about 2000°C. and above presents some difficult problems in heat transfer, in purification, and in container materials. For metals melting at such high temperatures, it is generally regarded as expedient to circumvent the more common melting and casting process by resorting to powder metallurgy. This circumvention is not accomplished without some penalties, the more notable of which are the relatively high cost of the powder metallurgy method and particularly the size limitations of its product. In an effort to overcome the inherent disadvantages of the powder metallurgy method, especially in respect to the limit of size, a project was begun in 1943 at the Climax Molybdenum Co. laboratory to develop a method of melting and casting molybdenum capable of producing larger bodies of molybdenum than were then obtainable. Later, from Feb. 1, 1944, to Aug. 31, 1945, the project was under the supervision of the National Defense Research Committee, Division One. In peacetime, too, there are needs for molybdenum, which make consideration of another process desirable; for example, large parts for heat engines generally, the omnipresent demand for metal of higher quality and lower cost, and the development of molybdenum-base alloys. This paper describes methods for melting and casting molybdenum, with details of the special process needed to make molybdenum castings ductile, and reports some of the properties of what may be regarded as a new, or at least modified, form of the metal. FIRST PROCESS FOR MELTING AND CASTING MOLYBDENUM The maintenance of a temperature greater than 2625°C. in a space large enough to melt several pounds of molybdenum may involve the loss of heat at a very considerable rate. For melting molybdenum, therefore, the source of heat must be of high potential and of fairly high power. Evidently, also, the source of heat must not impair the purity of the product. The electric arc operating in vacuum appeared to meet these requirements and was accordingly the first choice as a source of energy. A number of arc devices for melting molybdenum were examined, and several were tried. In the first experiment, a 20-kw., 60-cycle-per-second alternating-current arc was operated between two horizontal and opposed electrodes of molybdenum. In this arrangement the falling droplets of molybdenum solidified below the arc in an irregular mass. This experiment did not produce a useful casting, but the data obtained indicated that

Jan 1, 1946

By John L. Ham, Robert M. Parke

The melting point of molybdenum is 2625° + 50°C. Heretofore the metal has been considered too refractory to be melted in commercial quantities; hence, it has been formed into rod, wire, and sheet by the methods of powder metallurgy, wherein the temperatures do not exceed 90 per cent of the melting temperature. The manipulation of liquid metals at temperatures of about 2000°C. and above presents some difficult problems in heat transfer, in purification, and in container materials. For metals melting at such high temperatures, it is generally regarded as expedient to circumvent the more common melting and casting process by resorting to powder metallurgy. This circumvention is not accomplished without some penalties, the more notable of which are the relatively high cost of the powder metallurgy method and particularly the size limitations of its product. In an effort to overcome the inherent disadvantages of the powder metallurgy method, especially in respect to the limit of size, a project was begun in 1943 at the Climax Molybdenum Co. laboratory to develop a method of melting and casting molybdenum capable of producing larger bodies of molybdenum than were then obtainable. Later, from Feb. I, 1944, to Aug. 31, 1945, the project was under the supervision of the National Research Committee, Division One. In peacetime, too, there are needs for molybdenurn, which make consideration of another process desirable; for example, large parts for heat engines generally, the omnipresent demand for metal of higher quality and lower cost, and the development of molybdenum-base alloys. This paper describes methods for melting and casting molybdenum, with details of the special process needed to make molybdenum castings ductile, and reports some of the properties of what may be regarded as a new, or at least modified, form of the metal. First Process for Melting and Casting Molybdenum The maintenance of a temperature greater than 2625°C. in a 'pace large enough to melt several pounds of molybdenum may involve the loss of heat at a Very considerable rate. For melting molybdenum, therefore, the source of heat must be of high potential and of fairly high power. Evidently, also, the source of heat must not impair the purity of the product. The electric arc operating in vacuum appeared to meet these requirements and was accordingly the first choice as a source of energy. A number of arc devices for melting molybdenum were examined, and several were tried. In the first experiment, a 20-kw., 60-cycle-per-second alternating-current arc was operated between two horizontal and opposed electrodes of molybdenum- In this arrangement the falling droplets of molybdenum solidified below the arc in an irregular mass. This experiment did not produce a useful casting, but the data obtained indicated that

Jan 1, 1947

By John L. Ham, Robert M. Parke

The melting point of molybdenum is 2625° + 50°C. Heretofore the metal has been considered too refractory to be melted in commercial quantities; hence, it has been formed into rod, wire, and sheet by the methods of powder metallurgy, wherein the temperatures do not exceed 90 per cent of the melting temperature. The manipulation of liquid metals at temperatures of about 2000°C. and above presents some difficult problems in heat transfer, in purification, and in container materials. For metals melting at such high temperatures, it is generally regarded as expedient to circumvent the more common melting and casting process by resorting to powder metallurgy. This circumvention is not accomplished without some penalties, the more notable of which are the relatively high cost of the powder metallurgy method and particularly the size limitations of its product. In an effort to overcome the inherent disadvantages of the powder metallurgy method, especially in respect to the limit of size, a project was begun in 1943 at the Climax Molybdenum Co. laboratory to develop a method of melting and casting molybdenum capable of producing larger bodies of molybdenum than were then obtainable. Later, from Feb. I, 1944, to Aug. 31, 1945, the project was under the supervision of the National Research Committee, Division One. In peacetime, too, there are needs for molybdenurn, which make consideration of another process desirable; for example, large parts for heat engines generally, the omnipresent demand for metal of higher quality and lower cost, and the development of molybdenum-base alloys. This paper describes methods for melting and casting molybdenum, with details of the special process needed to make molybdenum castings ductile, and reports some of the properties of what may be regarded as a new, or at least modified, form of the metal. First Process for Melting and Casting Molybdenum The maintenance of a temperature greater than 2625°C. in a 'pace large enough to melt several pounds of molybdenum may involve the loss of heat at a Very considerable rate. For melting molybdenum, therefore, the source of heat must be of high potential and of fairly high power. Evidently, also, the source of heat must not impair the purity of the product. The electric arc operating in vacuum appeared to meet these requirements and was accordingly the first choice as a source of energy. A number of arc devices for melting molybdenum were examined, and several were tried. In the first experiment, a 20-kw., 60-cycle-per-second alternating-current arc was operated between two horizontal and opposed electrodes of molybdenum- In this arrangement the falling droplets of molybdenum solidified below the arc in an irregular mass. This experiment did not produce a useful casting, but the data obtained indicated that

Jan 1, 1947

By H. E. Elliott, R. S. Busk, A. T. Peters

One of the problems of the fabricator of metals and alloys is the propensity of some composition rarnges toward abnoermal grain growth during certain stages of fabrication. In this respect magnesium alloys are no exception among alloys. Fortunately, convenient foundry control methods have been developed by which the abnormal grain growth possible in certain magnesium-alloy castings can be suppressed. An unusual characteristic of magnesium alloys, however, is that castings of some composition ranges are subject to local grain growth during heat-treatment without the necessity of intentional mechanical stressing of the part prior to heat-treatment. This effect occurs only under certain critical casting conditions, and only in certain alloys of greater than about 8.5 per cent aluminum content, such as C alloy (Mg, 9 per cent A1, 2 Per cent Zn, 0.2 Per cent Mn) and G alloy (Mg, 10 per cent Al, 0.2 per cent Mn). The first observation of this phenomenon in cast magnesium alloys occasioned much surprise, since it is not observed in other meta1s- Jeffries and Archer1 have stated that "the grain size of cast metals, provided they have not been plastically deformed, cannot be changed by heating below the melting point." The study of the conditions leading to abnormal grain growth in cast magnesium alloys, and of the mechanism of this phenomenon, has led to some very interesting observations. Perhaps the most significant of these was the observation that stresses originating from cooling contraction in magnesium-alloy castings are the only stresses necessary, under certain conditions, to cause local recrystallization and subsequent grain growth in the casting during heat-treatment. Before recent developments, this phenomenon of abnormal local grain growth Was a definite problem in the production foundry on C alloy sand castings. Illustrated (Fig. I) is a picture of a casting scrapped because of this defect. A mottled effect is produced in coarse-grained areas by suitable etching solutions. The properties of metal in the affected area are much impaired by such grain coarsening. Ultimate tensile strengths of half the normal value have been measured in metal of this nature. In this paper are described the techniques that have been developed by The DOW Chemical Co. for studying, and in large measure solving, this production problem. Also discussed are studies of the mechanism by which excessive grain coarsening occurs, and the fundamental conditions that produce this effect. The abnormal grain growth discussed in this paper will be referred to as "germinasium since this term has been definedl as any process leading to an abnormally coarse grain size. This paper deals only with abnormal local grain growth that may occur during the solution heat-treatment of certain magnesium-alloy castings, as dis-

Jan 1, 1945

By Reno H. Sales

Our colleagues cannot in the future earn reputations and medals for achievements in milling and smelting ore and for successful management of mining companies, if some one doesn't keep finding and mining the ore to mill and smelt and to provide the basis for the good management. Good ore seems sometimes to be quite helpful to good management, and good ore is not as easy to find as it used to be. And there are still more reasons, why—when this honor had been decided upon and named for Mr. Daniel C. Jackling—it should be initially conferred on Reno H. Sales. . The terms of reference of the award are that it should be conferred upon an individual working in the fields of mining, geology, geophysics, who has made an outstanding contribution to the progress of technology in one or more of those fields. And in this initial year (the earlier years are the easiest) just that was done. I think I could get away with it amongst the old-timers of my generation if I say that this time they made the award to the individual, who made the outstanding contribution. But, as Al Smith used to say, "Let's look at the record." Really, the record is mixed up a little with extra-lateral litigation—the old-time "apex cases" under Section 2322 of the Revised Statutes. Reno Sales doesn't like such litigation, but there is little question that the urgency, generated by conflicting claims of intra-limital and extra-lateral rights, and consequent necessity for committing to records and maps the complications of Butte structure, did advance—and by several years—the first continuous, accurate, systematic, and scientific portrayal of the geological and mineralogical details of what is, after all, the most important and the most complicated copper district—at least in North America. Prior to Sales' time, some of the most eminent of geologists often waived details. One geologist took the judge to the window to show him the Rarus fault going through a notch in the Continental Divide. The entertaining testimony in the Bluebird litigation was as perfect in literary style as it was innocent of the criteria by which faulting and lack of continuity of vein structure are now recognized. At any rate, this need for an accurate record of structure was in the background—to whatever extent it was, or was not, the etiological agent—for formation of the Geological Department of the Amalgamated Copper Co. in and about the year 1900. Charles W. Goodale was at that time the head of the Boston & Montana, and John D. Ryan succeeded William Scallon as the president of Anaconda Copper Mining Co. in 1905. Horace V. Winchell, for years a specialist in extra-lateral litigation, was perhaps the man who at that date had the vision, the persuasive weight with the management, and the willingness to defend the idea of large current expenditures (as then viewed) for a complete and sys-

Jan 1, 1955

By H. E. Elliott, R. S. Busk, A. T. Peters

ONE of the problems of the fabricator of metals and alloys is the propensity of some composition ranges toward abnormal grain growth during certain stages of fabrication. In this respect magnesium alloys are no exception among alloys. Fortunately, convenient foundry control methods have been developed by which the abnormal grain growth possible in certain magnesium-alloy castings can be suppressed. An unusual characteristic of magnesium alloys, however, is that castings of some composition ranges are subject to local grain growth during heat-treatment without the necessity of intentional mechanical stressing of the part prior to heat-treatment. This effect occurs only under certain critical casting conditions, and only in certain alloys of greater than about 8.5 per cent aluminum content, such as C alloy (Mg, o per cent Al, 2 per cent Zn, 0.2 per cent Mn) and G alloy (Mg, i0 per cent Al, 0.2 per cent Mn). The first observation of this phenomenon in cast magnesium alloys occasioned much surprise, since it is not observed in other metals. Jeffries and Archer' have stated that "the grain size of cast metals, provided they have not been plastically deformed, cannot be changed by heating below the melting point." The study of the conditions leading to abnormal grain growth in cast magnesium alloys, and of the mechanism of this phenomenon, has led to some very interesting observations. Perhaps the most significant of these was the observation that stresses originating from cooling contraction in magnesium-alloy castings are the only stresses necessary, under certain conditions, to cause local recrystallization and subsequent grain growth in the casting during heat-treatment. of abnormal local grain growth was a definite problem in the production foundry on C alloy sand castings. Illustrated (Fig. r) is a picture of a casting scrapped because of this defect. A mottled effect is produced in coarse-grained areas by suitable etching solutions. The properties of metal in the affected area are much impaired by such grain coarsening. Ultimate tensile strengths of half the normal value have been measured in metal of this nature. In this paper are described the techniques that have been developed by The Dow Chemical Co. for studying, and in large measure solving, this production problem. Also discussed are studies of the mechanism by which excessive grain coarsening occurs, and the fundamental conditions that produce this effect. The abnormal grain growth discussed in this paper will be referred to as "germination," since this term has been defined' as any process leading to an abnormally coarse grain size. This paper deals only with abnormal local grain growth that may occur during the solution heat-treatment of certain magnesium-alloy castings, as dis-

Jan 1, 1945

By A. A. Stripling

The Cretaceous limestone wells of the Mara/Maru-caibo Dist. of Venezuela are extremely prolific producers. To maintain production on cessation of natural flow, large scale gas-lift operations were commenced involving high production rates on caring Flow. For the design of these gas-lift installations it was essential to have some knowledge of the pressure gradients involved in casing flow, so that the required injection pressures, optimum gas injection raws, etc., could be forecast. This paper presents a method of calculating these annular pressure gradients. Basically the method makes use of an energy balance equation coupled with an empirical energy loss factor derived from field data. The calculations have been put in a form suitable for "punch card-type" calculating machines. A set of gradient curves for Mara/Maracaibo conditions covering flow rates up to 12,000 B/D, and GOR's of 500 to 2,000 cu fd/bbl is presented. From these curves the flowing BHP can be predicted from surface data and the vertical pow performance under varying conditions of gas injection can be estimated. The method has been applied to La Paz and Mam gas-lift operations for over three years and has given consistently accurate results. INTRODUCTION The Cretaceous limestone fields of the Mara/Maracaibo area in Venezuela are characterized by the presence of widely distributed fissure systems. Under these conditions individual wells frequently have extremely high potentials and such wells are generally flowed on the casing-tubing annulus in order to reduce the pressure loss in vertical flow. To maintain production on cessation of natural flow, an extensive gas-lift system was planned. As a first approach to this gas-lift design problem, an attempt was made to construct a set of empirical flowing gradient curves from the available subsurface pressure data. Such a method has been used successfully for tubing-flow conditions in California by Gilbert'. Unfortunately, the empirical construction of casing-flow gradient curves presents additional difficulties, as pres- sure bombs cannot bc run in the casing-tubing annulus against high rates of flow. Thus, the Full flowing gradients cannot be defined by actual measurement and the best that can be done is to obtain spot pressures at the tubing shoe. Under these conditions a vast accumulation of BHP data is required to construct a set of gradients. To the La Paz and Mara fields the majority of the available flowing pressure measurements fall into a relatively narrow GOR range, in the neighborhood of the solution ratio. While there appeared to be reasonable prospects of constructing gradient curves for this limited range, measurements at higher GOR's, which were of major interest for gas-lift operations, were relatively few and the prospects of constructing empirical curves cor~spondingly remote. As an alternative approach, the possibilities of a mathematical analysis of vertical flow conditions were investigated. May and Laird2fV n 1934 presented an excellent analysis of the vertical-flow conditions in the Anglo-Iranian Oil Co.'s fields. Their analysis was based on an energy-balance equation and calculated the losses due to kinetic energy, friction and slippage separately. By combining these losses with the total calculated available energy, the required depth-pressure traverse could be deduced. On applying the method to La Paz conditions, good results were obtained for tubing flow at high tubing-head pressures. However, for lower wellhead pressures (300 psi and under) the discrepancy between calculated and measured values increased appreciably. It was considered that this was probably due to energy losses caused by slippage or liquid hang-up in a continuous gas phase, for which it was difficult to visualize any analytical approach. In 1952 Poettmann and Carpenter4 presented a method of pressure gradient calculation which, while based on an energy-balance equation similar to that employed by May and Laird, made no attempt to evaluate the various components making up the total energy loss resulting from irreversibilities of flowing fluids. Instead, they proposed a method of analysis which assumed that all significant losses for multiphase flow could be correlated in a form similar to that of the Fanning equation for frictional losses in single-phase flow. They then derived an empirical relationship linking measurable field data with a factor which, when applied to the standard form of the Fanning equation, would enable the energy losses to be determined. The total available

Abadilla, Quirico A. Catanawan, Tayabas, P I '20 Abbey, Robert Graham, District Mgr., The W. W. Sly Mfg. Co, 50 Church St, New York, N. Y. '21 Abbott,-A. N., Mines Supt, Mazapil Copper Co., Ltd .. Concepcion del Oro, Zac., Mexico. '23 Abbott, Clarence E., Mgr, Mines & Quarries, Tenn. Coal, Iron & R R Co. 1242 Brown Marx Bldg, Birmingham, Ala. '04 Abbott, Louis Benjamin, Chief Engr, Consolidation Coal Co, Elkhorn Div . Jenkins, Ky. '15 Abeel, George H., Jr., Cons Min Engr... . Box 427, Santa Monica, Cal. '18 Abel, Albert E., Asst. to Pres., Valley Mould & Iron Corp Hubbard, Ohio. '19 Abel, Raymond L., Asst. Prof., Dept. of Pet. Refin , Univ. of Pittsburgh Pittsburgh, Pa. '28 Abernathy, George Elmer, Prof. of Geol. & Min., Kansas State Teachers College. Pittsburg, Kans '20 ||Abernethy, D. Carl, Jr. Min. Engr., Hudson Coal Co . Scranton, Pa '27 Abey, Hiroshi, Min. & Met. Engr., Min. & Met. Dept, The Higher Technical School, Osaka, Japan. '17 Aborn, Robert H., Instructor in Met, Harvard University Cambridge, Mass. '19 Abozeid, Mahmood, Pet. Production Engr., Marland Oil Co Ponca City, Okla. '20 Abraham, Arthur W., Geol, Richfield Oil Co. Box 788, Bakeisfield, Cal. '20 Abraham, W. E. V., Member, Geol Staff of Burmah Oil Co, Ltd Nyaunghla. Upper Burma, India. '23

Jan 1, 1923

By P. Greenfield, P. A. Beck

RECENT work by J. Darby, Jr. in this laboratory has shown that the reported vanadium-rich limit of the s phase in the Co-V system at 1200°C is in error. The appearance of a second phase in s actually is restricted to alloys containing over 68 atomic pct V. The error in the original value is due apparently to a reaction that takes place along the numerous cracks in the s specimens between the alloy and the impurities present in the He + 8 pct H atmosphere in the annealing furnace. Such a reaction and the consequent appearance of a second phase can be suppressed if the alloys are sealed under vacuum in Vycor tubing. The new value of 68 atomic pct V for the vana-dium-rich limit of the s phase in the Co-V system effects slightly the s compositions calculated from average values of N, and N,. for various s phases. The standard deviation between experimental mean compositions and those calculated from the assumption that s is characterized by a constant number of 3d + 4s electrons per atom (N,), is slightly reduced from 9.1 to 8.8 pct. The maximum divergence for the V-Mn s phase is reduced from 15.5 to 14 atomic pct. The standard deviation calculated from constant electron vacancy numbers given by N.. = 4.66 (Mo + Cr + V) + 3.2 (Mn) + 2.2(Fe) + 1.71(Co) + 1.6(Ni) is now greatly reduced, as the maximum divergence for this correlation previously occurred in the V-Co system. This maximum divergence is reduced from 7.6 to 2.3 pct, and the standard deviation for all s- phases is reduced from 4.1 to only 2.9 pct. The correlation for electron vacancy numbers given by N. 5.66 (V when with Ni or Co) + 4.88 (V when with Mn or Fe) + 4.66 (Cr + Mn) + 3.3 (Mn) + 2.66 (Fe) + 1.71 (Co) + 0.61 (Ni) is made slightly worse, and the standard deviation increases from 2.8 to 3.9 pct. These changes, however, do not affect the conclusions of the paper.' The deviation between calculated and experimental s compositions is much less for either one of the electron vacancy correlations than for the correlation with the number of 3d + 4s electrons.

Jan 1, 1955

By Jorge Munoz Reyes, Guillermo

The new entity, Yacimientos Petroliferos Fiscales Bolivianos, created in 1936 for the development and exploitation of all petroliferous zones of Bolivia, including those formerly belonging to the Standard Oil Co., is doing its utmost to bring about rapid development and by this means to create a new source of revenue for the State. With this in view, Y.P.F.B. has opened a new field in the Samaipata region, on the main road between Cochabamba and Santa Cruz. Installation of machinery has begun for the drilling of several wells on the five anticlines that occur in this region. Work has also begun in the Saipuru field, on the Santa Cruz-Charagua highway, which was discovered by the Standard Oil and temporarily abandoned. In this new field, a topping plant will be installed, to supply gasoline and kerosene to Santa Cruz. Explorations are also being made on the neighboring structures of Saipuru. At the end of 1937, the committee that is to study the region of the Chapare in the northeastern part of Cochabamba, was organized. The structures were studied 10 years ago by Kirtley Mather and other geologists. It is hoped that by March 1938 this camp will begin work, as this zone gives promise of being valuable. Development The capacity of the refinery at Camiri has been enlarged in order that it may supply all the needs of that region. In order that the supply of crude may be adequate, several wells that had been almost abandoned by the Standard Oil are being cleaned out. New wells have been located at this camp following the principal anticlinal structure, and during the first half of the year 1938 several wells will be drilled. The same program is being followed in Sanandita but on a greater scale, as the nearness of this district to the Argentine border, which is the best market for the Bolivian petroleum of the south, allows immediate sale of the petroleum. Possibly a new refinery will be installed at this camp, as the one now in existence is only a rudimentary distillery. At the Bermejo camp, which is farther south, intensive work is being done to bring the wells into production. The Standard Oil produced limited quantities several years ago, but since 1927 the wells of this dis-

Jan 1, 1938

By Raymond B. Ladoo

TIIe milling of talc, as is the case with many non-metallic minerals, until recently, has not received adequate technical consideration, for the talc industry has become of importance only within the last decade. At first, talc was used only in the massive form, for foot warmers, griddles, and so on, and milling methods were unnecessary. As the demand for ground talc increased, producers adopted the machinery used in the milling of flour; in fact, many talc mills were rebuilt flour mills. Improvement has been slow, but today several types of grinding and separating machinery are in use; many of them, however, are still inadequate and inefficient. To determine the best methods of milling talc, it is necessary to understand the essential properties a talc must possess to fit it for a particular use. For toilet purposes, whiteness, freedom from lime and grit, fineness of grain, and good "slip" are essential. As a paper filler or coating, the talc must be white, uniform, and fine grained, have a good slip, and be free from grit and iron; freedom from lime is a disputed point. Fibrous talc is supposed to be superior to massive on account of the interlocking of grains in the paper, thus increasing its strength; this point, though, is in doubt. In general, talc for the paper industry need not be of as high quality or as fine grained as that used for toilet purposes. Talc is usually bought by sample, for which reason it is difficult to state the essential properties for use in paint, rubber, roofing, and so on. The adoption of standard screen tests and standard grades by producers is necessary before an accurate basis for manufacturing or selling standards can be established. Off-color talcs might be utilized, as in Germany and Austria, by the establishment of standard grades of colored talcs. The machinery to be used depends on whether the talc is fibrous, foliated, or massive; hard or soft; of uniform or variable grade; pure or impure. In some cases, it is possible to change the mining practice or to utilize different sections of the deposit in order to vary some of these factors, but in many cases these factors are fixed, so the milling must be designed to suit the conditions.

Jan 1, 1922

By G. Austin Schroter, Ian Campbell

ALTHOUGH there is now an extensive literature on the bleaching clays, not a great deal of material is to be found concerning the geological features of these deposits and their bearing on problems of exploration and development. At the same time, chemical and crystallographic research on the clay minerals during the past few years has laid a suitable foundation upon which to base conclusions of economic value drawn from field observations. All of the criteria and deductions herein presented are based upon extensive field work by the senior author, both in the United States and Canada, and when subjected to the ultimate tests of development and exploitation they have held up remarkably well, despite the fact that many of these conclusions apparently have not been reviewed in the literature heretofore. The nomenclature of the bleaching clays is rather confusing in the light of present-day commercial standards and has even led to litigation." The old term "fuller's earth" is largely based upon trade usage and the definition of the term therefore is dependent upon the changing standards of commerce. For statistical purposes the Bureau of Mines81 classes as "fuller's earth" all natural bleaching or filtering claylike materials that possess high adsorptive capacity without previous chemical treatmerit or activation. Conversely, the so-called activated or acid activated clays are now generally recognized as any clay mineral or mixture of the clay minerals whose adsorptive capacity has been developed to commercial standards by chemical or physical treatment. Therefore, without attempting to propose any additions to the nomenclature of bleaching clays, this paper will refer to naturally adsorptive clays and activable clays, respectively, for the two types indicated.

Jan 1, 1940

By C. L. Berrien

BEFORE the present company was formed, in 1916, each group of mines comprising the old organizations made its detailed daily and monthly mine cost records along the lines used before the consolidation; that is, there was no attempt made to standardize and compare the stope costs of all mines. The general cost sheets for all mines, however, were standardized, and cumulative labor cost sheets were compiled in the general superintendent's office. At most of the mines, a daily record or distribution sheet for each working place was kept, showing the number of men, hours of drilling, hours of timbering, hours of tramming, cars of ore, cars of waste, sticks of powder and feet of fuse. This information was kept by each shift boss and entered on the distribution sheet by him or, at some mines, by a tram boss. The superintendent solved his own problems under the direction of the general superintendent, but without coming in touch with other superintendents, either through records or general conferences. Probably 95 per cent. of the stopes were square-set worked by day's pay; there were some back-filling and shrinkage stopes. Many of the development places, such as shaft sinking, station cutting, drifting and raises had always been run by contract. These contracts were given, for no definite period, at so much per linear foot and were measured monthly, or when completed; the men being paid monthly. In some cases, fairness to the employee, was not maintained. On the whole, there was no standardization. There were no stope contracts, because of the objections of the Western Federation of Miners to general contracting in the mines.

Jan 2, 1922