Search Documents

By Charles H. White

Discussion of the paper of A. L. Sweetser, Tress., xxxviii., 236. CHARLES H. WHITE, Harvard University, Cambridge, Mass. (communication to the Secretary*) :-Those interested in leaching-processes gladly welcome contributions on either laboratory-tests, such as are reported by Mr. Sweetser, or mill-tests made on larger quantities of ore; and especially valuable are such reports, even with negative results, if the methods adopted are the outgrowth of an intimate knowledge of the conditions to be met. It seems very desirable, therefore, that as complete details as possible be given in reporting on such tests, particularly with respect to the character of the ore under examination. The questions of prime importance in the sampling of ore and in the making up of charges for laboratory-tests are those respecting its grade and uniformity. In Mr. Sweetser's paper the first of these questions is answered definitely, but the answer to the second, although apparent on inspection of the results, might be more strongly emphasized with advantage, since it is only on account of the extreme uniformity of the ore that the satisfactory results obtained could have been expected. It seems advisable to call attention to the fact that for average ores, and more particularly for uneven, or 11 spotted ores, the quantities used by Mr. Sweetser are not usually regarded as sufficient to insure satisfactory results. Let us examine the method somewhat in detail. The ore was crushed to pass a 5-mesh screen, and a sample of 45 lb. was taken out for assay and tests. The diameter of the largest grain of this ore, according to Richards,1 was 2.67 mm.-assuming here, as in the following cases, that the wire of the screen was of the largest size used for the purpose, thereby giving any possible advantage in this respect in favor of the method. The table in Richards's book, p. 852, shows that 45 lb. is a sufficient quantity for a fair sample with uniform ores, but not sufficient

Jan 7, 1908

By C. M. Smith

DELEGATES from 26 Local Sections and- Divisions of the Institute had three stimulating sessions during the Annual Meeting, a few topics still remaining to be discussed after the two Monday sessions.. The final session was held on Thursday morning. An abstract of the discussion will be transmitted to each delegate present. The topics included: Student relations. Section operation, membership, employment, MINING AND METALLURGY, a new nonmetallic minerals Division. licensing of engineers, and increased allotments of money to Local Sections. Some of the Sections felt that the present limit of $250 allotted to them - from the national treasury was insufficient to carry on their activities, and that this maximum should he increased. A resolution to this effect was passed for transmission to the Board of Directors.

Jan 1, 1935

By J. Murray Riddell

The method of treating hazards wherein value is decreased, is cited by R. D. Parks. Quite properly, the theory of probabilities is made use of when multiple hazards are under consideration. E. F. Fitzhugh, Jr. deals with the enhancement phase graphically and uses percentage of expectancy as derived by a study of conditions and the selection of a chance factor. It is believed that both of the authors referred to fully recognize the part which human judgment plays, and as coupled with experience, training, and the application of the theory of probabilities; in that respect the composer of this paper is in accord. Within the past year, the task of arriving at a mathematical method for handling the enhancement phase, and, additionally, coupling the negative and positive phases, was explored. In citing the hazard, or negative phase, reference is made to the text by Parks.

Jan 1, 1949

By C. M. Smith

HOWARD N. EAVENSON, acting for the last time as president of the Institute, presided at the annual business meeting on Tuesday afternoon at 4 o'clock. He spoke briefly of his visits with Local Sections last fall, and read a scholarly address on "Mineral Fuels and Civilization," scheduled for early publication in these columns. Karl Eilers presented the Treasurer's report, showing last year's income to be $134,967.44, compared with expenses of $133.266.51. Comparable figures for 1933 were $121,689.90 and $115,462.60. The Institute's peak income was in 1923 about $208,000. Newell G. Alford read the report of the Membership Committee showing 750 new members elected and placed on the rolls in 1934, compared with 328 in 1933. Losses by resignation last year were 81, compared with 262 in 1933; and 691 were suspended for non-payment of dues, compared with 747 the year before. Total membership, including 579 Student Associates, was 7742 at the end of 1934. Applications for membership have been coming in freely the last few months.

Jan 1, 1935

By C. E. Sims, F. W. Boulger, H. A. Saller

Most of the data on equilibrium constant and the deoxidations potentialities of those elements, considered to be stronger deoxidizers for steel than is silicon, have been calculated from thermodynamic data. The reason for this is, primarily, the obvious difficulty of obtaining direct experimental evidence of equivalent accuracy. This is an excellent use of the principles of thermodynamics and has given valuable data not otherwise available. Such results, of course, can be no more accurate than the physical constants used in the calculations, and one can never be sure that the basic data are either complete or accurate. In fact, as in the case with silicon,1 there are not only discrepancies among the calculated theoretical values of the equilibrium constant for deoxidation of steel but also between the theoretical and experimental values. It is highly desirable, therefore, to obtain experimental values for checks on calculated results whenever possible. If they disagree, both cannot be right, but if there is good agreement, their value is enhanced. The present work was done in an effort to obtain experimental evidence in regard to some of the common alloying additions but more particularly the so-called "strong" deoxidizers for steel. The method used was to determine the minimum concentration of the deoxidizer that would effect a certain definite degree of deoxidation in steel. The criterion of deoxidation was the change from the large globular Type I sulphide to the eutectic Type II as described by Sims and Dahle.2 This change is sharp and definite, and inasmuch as it can be produced with equal facility by aluminum, zirconium, and titanium, it is considered a manifestation of a certain degree of deoxidation and not an alloying effect. Ostensibly such a procedure could give only a comparison of deoxidizing powers and no absolute values. Nevertheless, repeated observations have shown that, when increasing increments of aluminum are added to a steel, the residual aluminum content begins to increase simultaneously with the appearance of Type II inclusions. Thus it seems warranted to postulate that the Type II inclusions appear coincident with the virtual elimination of FeO as an active constituent of the steel. Experimental Procedure The data obtained were primarily from the microexamination of polished and unetched specimens and from chemical analysis. Experimental heats weighing 200 to 250 lb were made in a basic-lined high-frequency induction furnace. The base composition was nominally that of a medium-carbon casting steel to which the appropriate additions were made. Specimens were poured into sand-cast ingots 3 in. in diam as shown in Fig 1. Sand-cast ingots were used to prevent chilling and to allow sufficient time in freezing for normal inclusions to form of a size large enough to be studied readily. In the first few heats, the tapered wall ingot was used, but in the majority, the extra large riser was used to prevent piping in heavily deoxidized steels. Specimens for microexamination were taken from the location shown in Fig 1, and drillings for chemical analysis were taken from a similar location. The procedure was to melt the base composition and deoxidize with the usual manganese and silicon additions and then to pour an ingot. The furnace was then tilted back, and the first increment of strong deoxidizer or special alloy was added and allowed to disseminate through the melt, with enough power on to hold the temperature constant, for 45 sec. Then a second ingot was poured. After this, another increment was added, and after the same holding time another ingot was poured. In this way from 9 to 12 ingots were poured from each heat, each successive ingot having progressively larger total additions of alloy. Eighteen heats were made altogether, and the range of alloys used and additions made are outlined in Table 1. The three principal types of sulphide inclusions found are illustrated in Fig 2. The globular Type I sulphides are characteristic of silicon-killed steels, the eutectic Type II are characteristic of steels deoxidized with a small amount of aluminum, while the larger, angular Type III are usually found in steels with a residual aluminum content above about 0.02 pct. In all specimens studied, the transition from Type I to II either did not occur at all or was very abrupt and clear cut. There never was any doubt as to just which increment produced the change, although the individual additions were small, in the order of 0.01 pct. The change from Type II to Type III was considerably less sharp, and, in some cases, both types were found together. Inasmuch as the formation of Type III sulphides is apparently not a deoxidation phenomenon, they will not be discussed here.

Jan 1, 1950

By C. W. Beattie, R. L. Solter

ALUMINUM-KILLED, low carbon steel sheets are used extensively for severe deep drawing and other difficult forming operations. They usually, but not always, have a characteristic grain structure in which the grains are elongated both in the lengthwise and in the transverse direction. As described by Burns and McCabe,&apos; a typical grain in the plane of the sheet has its two axes in that plane from 1 Y2 to 4 times as long as the axis normal to the plane of the sheet. Rickett, Kalin, and MacKenzieZ have also reported on the recrystallization behavior of such steel. The contrast in grain structures of fully processed sheets of aluminum-killed and rimmed steel is illustrated by Figs. 1 and 2. The elongated grain structure of the aluminum-killed sheet is not developed on all heats or lots of this metal, and studies of the factors controlling and influencing its formation are reported in this paper. Jeffries and Archerb tate that unstrained grains are normally equiaxed, but exceptions are common. For example, if a metal containing a material mechanically obstructing grain growth is subjected to considerable working followed by thorough annealing, it may exhibit grains consistently elongated in the direction of working. Our experiments demonstrate that aluminum-killed, low carbon steel is such a metal, and that the substance mechanically obstructing grain growth is aluminum nitride. The effectiveness of aluminum nitride in inhibiting grain growth has been found to be influenced by the degree of cold reduction, the rate of heating in annealing, the thermal history of the sample before cold reduction, and the residual aluminum content. A correlation between grain shape and austenitic grain coarsening temperature also was indicated and additional experiments demonstrated that aluminum nitride is also the principal cause for the fine grain characteristic of aluminum-killed steels. Manufacture In conventional practice, aluminum-killed sheet steel is manufactured from a low carbon steel containing approximately 0.02 to 0.07 pct residual (HC1 soluble) Al. With the exception of certain samples containing greater or lesser amounts of aluminum, the steels used in these investigations were within the following composition range: C, 0.03 to 0.06 pct; Mn, 0.28 to 0.38; S, 0.017 to 0.032; Al, 0.03 to 0.06; P, <0.01; and Si, <0.01. Properly heated ingots are rolled to slabs about 4 in. thick. After surface conditioning, the slabs are reheated to about 2300°F and hot rolled continuouslv to strip about 1/10 in. thick. The strip rolling is completed at a temperature of 1550°F or higher, and the strip is coiled, usually at a temperature near the lower critical transformation. After cooling, the strip is pickled to remove oxide, cold reduced 40 to 70 pet to final thickness, then annealed to 1250° to 1350°F in 20 to 80 ton charges, the size of which results in slow heating and cooling rates. Effect of Cold Reduction According to Sachs and Van Horn,&apos; the deformations of the individual grains in rolling are similar to those of the total volume. Thus individual grains would elongate in rolling according to the amount of cold reduction imposed. This is true theoretically, but as cold reduction increases the individual grains tend to fragment, and measured grain elongations become less than theoretical. The amount of grain elongation may be described by a numerical rating based on grain counts made by the intercept method. Specimens are polished normal to the plane of the sheet, with the polished surface extending parallel to the rolling direction. After etching, grain intercepts are counted along a 50 mm line on a micrograph of suitable magnification. In random locations parallel to the plane of the sample 20 counts are made and 20 are made in the thickness direction of the sample the average count in the thickness direction divided by the average count parallel to the plane of the sample gives a numerical rating of the grain shape called grain elongation. For example, a grain elongation of 2.00 means that the average grain is twice as long as it is thick. The average of both counts may be converted to grains per sq mm by a nomograph relating intercept counts and grain count. By the same procedure the grain elongation in the plane of the sheet but transverse to the rolling direction may be determined, using transverse metallographic samples. A comparison of theoretical and measured grain elongation was obtained on an aluminum-killed

Jan 1, 1952

By G. A. Vissac

O. R. LYONS *—I wish to thank Mr. Vissac for his compliment. I hope that his paper is not only well received, but that it will serve to bring forth more papers on the subject of thermal drying. One of the primary purposes of the work performed by Battelle for Bituminous Coal Research in investigating the thermal drying of coal was to stimulate other investigators and to get them to contribute their knowledge in the form of papers such as this one. We at Battelle and the personnel of Bituminous Coal Research are very gratified that Mr. Vissac and other persons have responded in this matter of the thermal drying of coal. I wish to state that I think that Mr. Vissac&apos;s paper is a very clear and easily understood description of a method of calculating the design requirements for a screen type drier, and I think that it would be exceedingly valuable to operators and to those who intend to purchase any type of thermal drier and use it in the future, if the manufacturers or operators who have such information for other types of driers would provide the same type of information for the other makes of driers now on the market. 1 also wish to point out—an idea that is new to me, and I know is new to most of the operators of driers in the United States-—the idea of recovering the heat that is normally lost in the coal and in the exhaust gases. This heat is not being recovered at most (of the thermal drying operations in the United States, and the possibility of recovering it should be called to the attention of every single one of those operators. I know many of them have never given any thought to the matter, but they will be interested once they realize the ease with which it could be done and the savings that could be realized. I also wish to compliment Mr. Vissac for presenting the method of analysis that he uses to determine the difficulty of drying any particular coal. It is a very simple method, and yet it seems to me that it should be a very effective, very efficient method for determining the difficulty of drying for his particular problems. C. Y. HEINER*—I do not know that I can add anything very illuminating to what Mr. Vissac has said. I think anything that Mr. Vissac said in regard to coal drying is a contribution because, to my personal knowledge, he has studied the matter carefully for many years and made many valuable contributions. I am not too familiar with coal drying problems in the east, but I know in the west we have not made enough coal drying studies. I think coal operators too often just take the coal as it is and make more or less the best of it. There are relatively few washing plants in the west now, and so the problem has not come to the front as much as it probably will in the future. In this connection, it seems to me that this matter of drying the raw coal, as Mr. Vissac brings up, is an extremely important one. We have not a continuous miner ourselves, yet, but we expect to get some this year, and we think the percentage of fine coal-—that is, minus 3/16 in.—will double. We have about 20 pct minus 3/16 in. in the 8 in. by 0 size now, and we think we will likely have 40 pct, which will have a surface moisture of the order of 8 pct. To wash it satisfactorily, we will have to dry the raw coal first in order to screen it, and after that, I suppose, there will have to be dry cleaning of some sort. We have not really used dry cleaning on fines in the west yet to my knowledge, but it is a matter that has to be faced by the industry, and I am very hopeful that Mr. Vissac&apos;s study will assist us in that connection. W. L. McMORRIS*-In my company we are preparing largely metallurgical coal for a great number of byproduct coke plants. The most outstanding thing to me about the requirements of moisture in the finished product is that there is a different requirement for almost every coke plant. Each operator has a different set of factors on which he establishes his coking costs where they involve moisture. For our corporation operations in Birmingham, my company does not produce the coal, but in Birmingham they are getting away with moistures very much higher than our plant at Clairton, Pa., would tolerate. The moisture that we have to produce for the plants along the lakefront where they are subject to much more severe weather is something else again. We have not tackled heat drying, primarily because our customers do not know what heat drying will do to the coking characteristics of the coal. If the temperature of drying can be held down

Jan 1, 1950

By D. Y. F. Lai, R. J. Borg

Tracer diffusion of Fe59 has been measured in the a-stabilized Fe-1.8 at. pet V alloy from 700° to 1500°C. The activation energies are obtained in both the presence and absence of magnetic order. Furthermore, it is established that diffusion in the alloy is identical to that in pure iron and consequently the values of Do and Q accurately represent the temperature dependence for self-diffusion. The purpose of this investigation is to obtain an accurate estimate of the temperature dependence for self-diffusion in bee iron in both the presence and absence of magnetic order, and, in so doing, to establish the temperature range of the magnetic effect.&apos;" As the temperature interval suitable for diffusion measurements is severely limited in both bee phases of pure iron because of the intervening fee ? phase, the experiments were performed on an a-stabilized alloy containing 1.8 at. pet V. This alloy is bee over the entire range from room temperature to the melting point. Although there have been several independent investigations of self-diffusion of iron in a, iron,1, 3-6 there still exists considerable disagreement regarding the values of Do and Q for the paramagnetic region. The two systematic studies of diffusion in 6 iron6, 7 previously reported are also only in fair agreement; but in view of the extremely small temperature range available for diffusion studies, i.e., 1390o to 1535oC, this is not surprising. It is comparatively easy to obtain accurate values of Do and Q for the a-stabilized alloy inasmuch as measurements can be made over the entire temperature range -700o to 1500°C. However, in order to assume that these same values apply to pure iron requires careful comparison of the data in the a, and 6 regions in both the alloy and pure iron. We have made several measurements in the appropriate temperature ranges and are unable to establish any systematic difference between the diffusion coefficients of iron in pure iron and in the alloy. We therefore conclude that the values obtained for the alloy are truly applicable to pure iron; the complete evidence favoring this conclusion will be discussed later in this paper. EXPERIMENTAL The experimental methods will be given here only in barest detail since they have been thoroughly de- scribed elsewhere.l, 7 The alloy was prepared by induction melting and chill casting under argon. Diffusion samples were machined from the ingot and annealed in hydrogen for several days at 900°C to give an average grain diameter of 1 to 2 mm. The penetration profiles of the tracer were established by a sectioning technique, the residual activity being counted after the removal of each section. The tracer used is Fe59 which emits two high-energy ? rays of 1.098 and 1.289 Mev, respectively; these were detected by a ? scintillation counter equipped with a pulse-height analyzer. For the measurements in the temperature range -700o to 1130°C the samples were vapor-plated with Fe59, encapsulated in quartz under vacuo, and annealed in resistance-heated furnaces which are controlled to ±1°C. The specimens diffused at higher temperatures are prepared as edge-welded couples, the two halves being separated by a thin washer of the alloy to prevent sintering. The diffusion anneal is then carried out by inductive heating under a dynamic vacuum. The temperature is monitored pyrometrically. RESULTS The diffusion coefficients are obtained from the penetration profiles in the usual way using the error-function complement relationship. The results over the entire temperature range are shown in Fig. 1. In the linear region, 900o < t > 1500°C the least mean squares (lms) values of the diffusion coefficients are given by D = 1.39 exp[-(56.5 ± 1) x 103/Rt] cm2/sec [l] The average departure of the measured diffusion coefficients from the values given by Eq. [1]In order to determine whether or not the slope is truly constant over the entire range from 900" to 1500°C, the data are arbitrarily divided into two groups, the first containing values between -900" and 1133°C and the second between -1133o and 1500°C. The lms values for the two groups are given by Eqs. [2] and [3]: D = 0.519 exp[-55.7 x 103 /RT](900° to 1133°C) cm2/sec [2] D = 1.45 exp[-56.7x103/RT] (1133° to 1500=C) cm2/sec [3] Thus, there is no significant difference between the high- and low-temperature segments of the linear region. This not only assures us of the consistency of the values obtained by induction heating as compared to those obtained from the resistance-heated

Jan 1, 1965

By A. J. Lena, M. F. Hawkes

Changes in hardness, tensile properties, microstructure, electrical resistance, and X-ray diffraction effects indicate that lattice strains are necessary for the embrittlement of ferritic stainless steels when heated for relatively short times at 475°C (885°F). It is suggested that 475°C (885°F) embrittlement is due to the accelerated formation of an intermediate stage in the formation of s under the influence of these strains. FERRITIC stainless steels (low carbon alloys of iron with more than 15 pct Cr) are subject to two forms of embrittlement when heated in the temperature range of 375° to 750°C. The embrittlement which occurs after long time heating between 565" and 750°C is well understood; it is caused by the precipitation of the hard, brittle s phase. Sigma is an intermetallic compound of approximate equi-atomic composition with an extended range of formation in Fe-Cr alloys. The maximum temperature at which this form of embrittlement can occur is dependent upon chromium content; and is approximately 620°C for a 17 pct Cr steel and 730°C for a 27 pct Cr steel. The other form of embrittlement occurs after relatively short heating periods in the range of 375" to 565°C; in the higher chromium steels, hours may be sufficient as compared to months for s embrittlement. This phenomenon is not at all well understood and several controversial theories have been proposed. The rate and intensity of embrittlement increase with increasing chromium content but the maximum rate occurs at 475°C re-gardless of chromium content. As a result of this, the phenomenon has been termed 475°C (885°F) embrittlement. The effect of 475°C embrittlement on the properties of ferritic stainless steels has been thoroughly reviewed by Heger.1 The embrittlement causes a pronounced decrease in room temperature impact strength and ductility, a large increase in hardness and tensile strength, and a decrease in electrical resistivity and corrosion resistance. Microstructural changes accompanying embrittlement are minor and difficult to interpret with a general grain darkening, appearance of a lamellar precipitate, grain boundary widening, and precipitation along ferrite veins having been reported at various times. With the exception of reported line broadening, X-ray diffraction studies by conventional Debye analysis of solid samples have been of little value. BY making use of electron diffraction methods, Fisher, Dulis, and Car-roll&apos; have recently shown the existence of a chromi-um-rich, body-centered cubic phase in 27 pct Cr steels which had been aged at 482°C (900°F) for as long as four years. Two types of theories have been advanced to account for the embrittlement. The first of these requires the precipitation of a phase not inherent in the Fe-Cr system with various investigators suggesting a carbide,3 nitride,3 phosphide,4 or oxide." Theories of this type have difficulty accounting for the influence of alloying elements on the embrittlement and for the facts that a minimum chromium content is necessary for embrittlement and the intensity of embrittlement increases with increasing chromium content. The second type of theory that has been proposed relates 475°C embrittlement to s phase formation which is inherent in the Fe-Cr system. An assumption of this kind can adequately explain the influence of alloying elements, for they exert an effect on 475°C embrittlement similar to that on s phase for-mation as can be seen in Table I. The minimum chromium content is essentially the same for both phenomena and it has been shown12,13 that s is a stable phase in the embrittling temperature range. In addition, it has been reported14,15 that pure alloys embrittle to the same extent as commercial type alloys. There are, however, several factors which have prevented complete acceptance of a s phase theory. Foremost of these is that the embrittlement can be removed by reheating for short time periods above 600°C, which in the higher chromium steels is within the stable s region. No s has ever been observed after one of these curing treatments, nor has any s been found as a result of embrittlement at 475°C. In addition, the simple precipitation of s cannot explain the time-temperature relationships for reactions between 350°and 750°C. This behavior is shown schematically in Fig. 1. Newell 16 and Ried-rich and Loib4 have shown that 475°C embrittlement follows a C-type curve as illustrated, while Short-

Jan 1, 1955

By Charles E. Lundin

The character of the Er-D system was established by determining pressure-temperature-composition relationships. A Sieuerts&apos; apparatus was employed to make measurements in the temperature range, 473" to 1223"K, the composition range of erbium to ErD3, and the pressure range of 10~s to 760 Torr. The system is characterized by three homogeneous phase regions: the nzetal-rich, the dideuteride, and the trideuteride phases. These phases and their solubility boundaries were deduced from the family of isotherms of the system zchich relate the pressure-temperature-composition variables. The equilibrium plateau decomposition relationships in the two-phase regions were determined from can&apos;t Hoff plots to be: The differential heats of reaction in these two regions are AH = - 53.0 * 0.2 and -20.0 *0.1 kcal per mole of D2, respecticely. The differential entropies of reaction are AS = - 36.3 * 0.2 and - 31.0 * 0.2 cal per mole D2. deg, respectively. Relative partial molal and intepal thermodynamic quantities were calculated from the pure metal to the dideuteride phase. The study of the Er-D system was undertaken as a logical complement to an earlier study of the Er-H system.&apos; The primary interest was to compare the characteristics of the two systems and relate the difference to the isotopic effect. Studies of rare earth-deuterium systems by other investigators have been very limited in number and scope. Furthermore, there is even less information available wherein an investigator has systematically compared a binary rare earth-hydrogen system with the corresponding rare earth-deuterium system. The available information consists primarily of dissociation pressure measurements in the plateau pressure region of a few rare earths. Warf and Korst&apos; determined dissociation pressure relationships for the La- and Ce-D systems in the plateau region and several isotherms for each system in the dideuteride region. They compared these data with those of the corresponding hydrided systems. The study of these systems as a whole was very cursory and did not give sufficient data for a thorough comparison of the effect of the hydrogen vs the deuterium in the respective rare earths. The heat capacities and related thermodynamic functions of the intermediate phases, YH, and YD2, were determined by Flotow, Osborne, and Otto,~ and the investigation was again repeated for YH3 and YD3 by Flotow, Osborne, Otto, and Abraham.4 This investigation studied only these specific phases. Jones, Southall, and Goodhead5 surveyed the hydrides and deu-terides of a series of rare earths for thermal stability including erbium. They experimentally determined isotherms of selected hydrides and plateau dissociation pressures for deuterides. These data allowed comparison of the enthalpy and entropies of formation of the dihydrides and dideuterides. To date, no one rare earth has been selected to thoroughly establish the complete pressure-temperature-composition (PTC) relationships of binary solute additions of hydrogen and deuterium, respectively. The objective in this investigation was to provide the first comparison of a complete family of isotherms of a rare earth-deuterium system with those of a rare earth-hydrogen system. This would allow one to determine what differences exist, if any, in the various phase boundaries and the thermodynamic relationships in various regions of the systems. I) EXPERIMENTAL PROCEDURE A Sieverts&apos; apparatus was employed to conduct the experimental measurements. Briefly, it consisted of a source of pure deuterium, a precision gas-measuring buret, a heated reaction chamber, a mercury manometer, and two McLeod gages (a CVC, GMl00A and a CVC, GM110). Pure deuterium was obtained by passing deuterium through a heated Pd-Ag thimble. A 100-ml precision gas buret graduated to 0.1-ml divisions was used to measure and admit deuterium to the reaction chamber. The reaction unit consisted of a quartz tube surrounded by a nichrome-wound furnace. The furnace temperature was controlled by a recorder-controller to . An independent measurement of the sample temperature in the quartz tube was made by means of a chromel-alumel thermocouple situated outside, but adjacent to, the quartz tube near the specimen. Pressure in the manometer range was measured to k0.5 Torr and in the McLeod range (10~4 to 10 Torr) to *3 pct. The deuterium compositions in erbium were calculated in terms of deuterium-to-erbium atomic ratio. These compositions were estimated to be *0.01 D/Er ratio. The erbium metal was obtained from the Lunex Co. in the form of sponge. The metal was nuclear grade with a purity of 99.9+ pct. The oxygen content was reported to be 340 ppm and the nitrogen not detectable. Metallographically the structure was almost free of second phase (<i vol pct). A quantity of sponge was arc-melted for use as charge material. The solid material was compared with the sponge in the PTC relationships. They were found to be identical. Therefore, sponge material was used henceforth, so that equilibrium could be attained more rapidly. The specimen size was about 0.2 gr for each loading of the reaction chamber. The procedure employed to obtain the PTC data was to develop experimentally a family of isothermal curves of composition vs pressure. First, a specimen

Jan 1, 1969

By B. L. Averbach, M. F. Comerford, M. B. Rough

The volume fraction of ß phase was determined in a Ti-6Al-4V alloy by measurements of integrated diffraction intensities. The (0002), and (100)ß diffraction lines were chosen because this combination minimizes the errors resulting from preferred orientation. The difficulties arising from fluorescence radiation were eliminated by use of a diffracted beam monochromator. A specimen quenched from 1475OF (800°C) contained approximately 5 pct ß, but in specimens quenched from higher temperatures no ß was found. The ß phase formed during aging, and in specimens solution treated at 1570oF (855oC) approximately 10 pct ß was present after aging at 1000°F (540°C) for 24 hr. This ß appears to form by decomposition of martensitic a&apos;. ThE kinetics of the reactions which occur during the heat treatment of titanium alloys are complex &apos; and not completely understood. It has been proposed that hardening occurs in some alloys&apos; on aging by the precipitation of a transition phase w followed by the formation of the stable a and ß phases. It has been proposed for other alloys2 that the a&apos; marten-site decomposes by precipitating finely dispersed a particles. Most investigations have been hampered by the difficulties of determining quantitatively the amounts of the various phases present. This paper is concerned with the measurement of the amount of ß phase by an X-ray method, similar to one developed for the determination of retained austenite. The principal new feature was the use of a mono-chromator in the diffracted beam in order to reduce the fluorescence arising from the sample. EXPERIMENTAL PROCEDURE The experiments were carried out on an alloy of nominal composition Ti-6Al-4V (actual weight percentages: 6.2 Al, 4.1 V, 0.02 Mn, 0.17 Fe, 0.005 H, 0.03 C, and 0.02 N). The material was received as 5/8-in.-diam centerless ground rods in the annealed condition. The heat treatments were carried out in a vacuum of approximately 0.03µHg. The X-ray intensity measurements were made on 3/8-in. thick discs. The surface was prepared by grinding off about 0.060 in. and electropolishing in a solution af 60 ml (70 to 72 pct) perchloric acid in 1000 ml glacial acetic acid with a current density of 0.5 amp per sq cm.q The X-ray determination is based on the proportionality of the diffracted intensity of each line to the volume fraction of the corresponding phase. In calculating the intensities for a powder sample it is assumed that a large number of grains con- tributes to the diffracted intensity and that the grains are oriented at random. The presence of preferred orientation introduces serious errors in the relative intensities. The material used in this investigation exhibited a strong preferred orientation, which could not be removed by heat treatment. Other investigators have also found that preferred orientation may be retained after phase transformations. Glen and pugh5 performed a detailed analysis of the randomness expected after several allotropic transformations, but stated that this is not observed. Burgers,6 and Burgers and Ploos van Amstel,7 found that, in zirconium, the original orientation is retained after two phase transformations. Newkirk and Geisler8 observed similar behavior in titanium. On the basis of this evidence, it appears that, in the absence of plastic deformation, textures present in annealed titanium alloys are retained. Heating an a-ß alloy to the all-ß region and subsequent cooling to room temperature do not make the orientation of the mar-tensite different from that of the original a phase. In the present investigation it was possible to take advantage of the crystallographic relationships involved in the martensitic transformation to minimize the errors associated with preferred orientation. The relative orientation for titaniu-m marten-site9 takes the form (0001), 11 (110)ß; [1120], 11 [lll]ß. The same relationship has been proposed for zirconium&apos; and certain titanium-base alloys.10-12 Additional sets of approximately parallel planes have been determined for titanium-nickel alloys." The influence of preferred orientation can be minimized by comparing intensities from parallel planes in the two related phases. If it is assumed that each family of planes in a given phase is equally well populated, the effect of preferred orientation can be eliminated by using the normal multiplicity for the family of planes since each set of parallel planes is equally preferred for any orientation of the sample relative to the X-ray beam. The most suitable combination of reflections in the Ti-6A1-4V alloy appeared to be (0002), and (110)ß It must be recognized that the ß formed during aging of the Ti-6A1-4V alloy is a precipitate rather

Jan 1, 1960

By P. M. Kelly, E. P. Butler

Four Mn-CLL alloys, containing 60, 70, 80, and 90 pct Mn, respectively, have been examined in the quenched and the quenched and aged conditions using electron microscopy and electron, neutron, and X-ray diffraction. After certain heat treatments the alloys transform from fee to fct and in the tetraom1 condition show a domain structure parallel to {101} planes. Neutron diffraction indicates that the domains are antiferrornagnetically ordered. The domain boundary contrast has been examined using bright- and dark-field microscopy, and the contrast effects observed under favorable conditions have been used to deduce the c axis orientation in each domain. The domains are extremely mobile and can be nucleated at precipitate particles and screw dislocations. The domain mobility is responsible for the high damping capacity. In the aged material a Mn precipitates in the Kurdjumov-Sachs orientation and results of both electron microscopy and neutron diffraction indicate that the matrix separates into two components—one rich in manganese and the other rich in copper. ALLOYS of manganese and copper have the unusual combination of a high damping capacity and good mechanical properties and have been the subject of a number of investigations as part of a general interest in high damping capacity alloys for engineering purposes.&apos;,&apos; SO far, however, there has been no reported electron metallographic study of these alloys. The Mn-Cu system has an extensive range of solid solubility at high temperatures, and the equilibrium phases are expected to be y (fee) and a Mn. The high damping capacity is associated with a metastable tetragonal structure of variable c/a ratio, which forms from the high-temperature y phase. This latter phase becomes more difficult to retain as the manganese content increases, and alloys containing more than 82 wt pct Mn undergo a reversible martensitic fcc — fct transformation on quenching. The X-ray work of Basinski and christian3 showed that the Ms temperature for the transformation was below room temperature for alloys in the range 70 to 82 pct Mn and increased linearly with manganese content. When quenched from the y region, alloys in the range 50 to 82 pct Mn are cubic at room temperature, but become tetragonal if aged at temperatures between 400" and 600°C. The martensite transformation occurs on cooling from the aging temperature. Tetragonal alloys have a banded microstructure and the bands analyze to be traces of (110) planes. Similar microstructures have been observed in In-Tl4 and in other manganese-base systems, such as Mn-Au5 and Mn-Ni.6 The mobility of the bands in Mn-Cu alloys can be demonstrated by optical examination of a polished specimen surface subjected to a cyclic stress.7 The bands appear and disappear as the stress is varied, and X-ray measurements of the (200,020) and (002) peak intensities confirm that a reversible reorientation of the tetragonal structure occurs. Meneghetti and sidhu8 investigated the magnetic structure of Mn-Cu alloys and found antiferromagnetic ordering in furnace-cooled alloys of composition >69 at. pct Mn. Magnetic super lattice reflections occurred at the (110) and (201) positions and the proposed structure was fct with the spins along the c axis. A more complete investigation by Bacon et al.9 confirmed this structure. The magnetic ordering temperature Tn was found to increase linearly with manganese content in the same way as the Ms temperature, and at any composition, Tn > Ms. This relationship suggested that the magnetic ordering was responsible for the cubic — tetragonal transformation in the manganese-rich alloys. The purpose of this investigation was to study the mechanism of high damping and the structural changes that occur on aging. The main technique used was transmission electron microscopy, but X-ray and neutron diffraction experiments were also carried out. EXPERIMENTAL Materials and Heat Treatment. The four alloys, provided by the Admiralty Materials Laboratory. were of nominai composition 60, 70, 80, and 90 Mn and all had low impurity levels, <0.05 pct C, <0.2 pct Fe. This material was cold-rolled to 200-µ strip with intermediate annealing and then given a final heat treatment of 24 hr in the range 800° to 900°C followed by water quenching. An identical heat treatment was given a length of 3/4-in.-diam bar of the 70/30 alloy from which the neutron diffraction specimens were machined. It was suspected that the tetragonal structures would be metastable at room temperature, and so the alloys were not aged until required for experiments. After aging in a salt bath the alloys were water-quenched. Thin Foil Preparation. Initial thinning to 50 to 75 µ was possible in a solution consisting of: 50 ml nitric acid 25 ml acetic acid 25 ml water The surface deposit and grain boundary etching was removed by a final electropolish at around 20 V in an electrolyte consisting of:

Jan 1, 1969

By John H. Schemel

Large Zircaloy-2 hammer or press forged bars did not exhibit the uniform excellent corrosion resistance to steam normally expected of the alloy in wrought form. Weight gains of coupons cut from forged bars were 40 to 60 mg per sq dm compared to the 28 mg per sq dm obtained on hot rolled sheet and strip. The mechanism of this corrosion and its relation to microstructure is discussed. After these observations, a solution heat treatment followed by rapid cooling was tried on coupons from eight heats of forged bars. The basket-weave structure resulting from the quench did not show agglomeration of intermetallic compounds. These coupons showed uniformly good corrosion resistance with weight gains very close to the 28 mg per sq dm expected of Zircaloy-2 after the 14-day steam test. A large forging was solution heat-treated and tested for structure, mechanical properties, and corrosion resistance. Corrosion resistance was excellent and uniform throughout the section. The normally anisotropic mechanical properties were changed to completely iso-tropic. Strength levels were raised while there was a small loss in ductility at the service temperature. Tempering of the quenched structure below the ß transus did not improve the ductility at the test temperature of 600°F. ZIRCALOY-2 end caps for nuclear fuel elements Zircaloy-2 is an alloy of 1.5 pct Sn, 0.1 pct Fe, 0.1 pct Cr, and 0.05 pct Ni, balance hafnium-free zirconium patented by Westing-house Electric Co. used in pressurized water reactors are machined from large hammer-finished forged bars. The bars forged for this application range from 3 1/2 in. to 7 1/2 in. squares. One of the tests used to evaluate Zircaloy-2 for this service is a 14-day exposure to very high-purity steam at 75oF and 1500 psi pressure. Normally wrought products will exhibit a black lustrous film of zirconium oxide after the test and show a weight gain of approximately 28 mg per sq dm. Coupons representing the forged bars exhibited a wide variety of corrosion results ranging from acceptable black coupons to some covered with white crystals of zirconium oxide that had weight gains of nearly 100 mg per sq dm. One of the most common effects was a white corrosion product that looked like a stain to some observers and the outline of massive metal grains to others. Very careful specimen preparation prior to the corrosion test did not affect the result and metallographic examination did not reveal a structural feature of a size and shape that would correlate with the corrosion product. In addition to the relatively poor corrosion resistance, the forged product was not as ductile as desired. The problem of obtaining uniform and more acceptable properties in these heavy-forged sections seemed to be a function of the microstructure of the metal and, in particular, the distribution of the intermetallic compounds. None of the four alloying elements however are appreciably soluble in a zirconium and are present as compounds which usually appear scattered randomly throughout the structure. Moudryl showed that the distribution of these intermetallic compounds in Zircaloy could be related to a ostringero corrosion failure. Grozier et al. discussed another structural defect that causes a similar corrosion effect. In this case, an elongated gas-void was determined to be the cause. M. L. Picklesimer held in his discussion of the Grozier paper that at least a part of the observed =stringersn were caused by the distribution of the intermetallic compounds. He proposed a

Jan 1, 1962

By Frank M. Monroe, James R. Cost

The solubility of nitrogen in vanadium is determined from 275" to 575°C by measuring the height of the nitrogen internal friction peak of equilibrated V-N alloys. The proportionality constant at 275°C between the internal friction peak height (Q- 1) and the atom percent nitrogen in solution is found to be 0.095 per at. pct for nitrogen concentrations up to 0.8 at. pct. The heat of solution of the nitride in vanadium is 5500 cal per mole. The solubility of nitrogen in the Group V metals is discussed. LITTLE work has been performed on the vanadium-nitrogen terminal solid solution. Hahn1 found the solubility for nitrogen to be very small and reported the existence of a hexagonal phase of composition near that of V2N at the solubility limit. Rostoker and Yamarnoto2 reported the solubility to be at least 3.5 at. pct at the melting point and to be less than this value at 900°C. In addition, they reported from X-ray diffraction studies that nitrogen in solution produces tetragonality in the vanadium lattice. An X-ray study by Schonberg3 has confirmed the results of Hahn but indicated that the tetragonality observed by Rostoker and Yamamoto was due to the presence of oxygen in their specimens. Beatty4 has performed lattice parameter and hardness measurements on terminal solid solutions and found the upper limit of the solubility to be at least 0.66 at. pct N. No measurements have been made of the pressure-temperature-composition relationships (P-T-X) for the terminal solid solution. As a part of a research program on gas-metal equilibrium, an attempt was made to study the P-T-X relationships in the V-N system using both the internal friction and the gas equilibration methods which have been successful with the Nb(Cb)-N and Ta-N systems (see Ref. 5 for a review of this work). Extensive investigation, using the gas equilibration methods, showed this method not to be applicable with vanadium This was presumably due to the gettering action of vanadium sublimed on the walls of the Sieverts apparatus. Thus, the nitrogen pressure relationships with temperature and composition were not obtained. The internal friction methods were, however, found to be applicable, and the temperature-composition relationships are reported in this paper and compared with similar results for the Nb-N6 and Ta-N7 systems. The existence of a Snoek internal friction peak due to nitrogen in solution in vanadium has been clearly demonstrated. 8-10 Powers and Doyle found the peak to be at approximately 275°C for frequencies near 1 cps.8 In a subsequent paper10 they reported the proportionality constant at 275°C between the internal friction peak height (Q-1) and the concentration of ni- trogen in solution (in atom percent) as 0.06 per at. pct. The studies of Stanley and wert9 indicated qualitatively that the height of the Snoek peak decreased with aging at the peak temperature and thus suggested that internal friction methods were suitable for study of the solubility. EXPERIMENTAL METHOD The vanadium for this investigation was of particularly high purity. It was obtained from the Ames Laboratory of the U.S. Atomic Energy Commission, Ames, Iowa in the form of a 1/2-in. diam, three pass zone-refined ingot. The electrical resistivity ratio (p300ºk/p4ºk) was 160. The initial composition was determined as follows: Carbon 200 ppm Oxygen 150 ppm Chromium <50 pprn Iron 125 ppm Silicon <50 ppm Other metallic 100 pprn The initial vanadium ingot was fabricated to 30-mil wire by swaging and wire drawing without the need of intermediate annealing. Lengths of this wire were then further purified (particularly for oxygen) by outgassing at 10-6 torr at 1400°C for 4 hr. The outgassing treatment resulted in specimens with a bamboo grain structure and a lustrous appearance. Desired amounts of nitrogen were added to the outgassed wires in a Sieverts apparatus in which known amounts of nitrogen were equilibrated with the wire at 1300°C. Nitrogen concentrations were produced in the desired range from less than 1 to 10 at. pct N. Monitoring of the partial pressure of nitrogen in the Sieverts apparatus indicated that at 1300°C equilibrium between the nitrogen gas and the vanadium was obtained within 10 min. Relatively rapid cooling from the nitrogen addition temperature was obtained simply by turning off the specimen heating current and cooling to room temperature in the partial pressure of nitrogen. Internal friction measurements of wire specimens were made under forepump vacuum in a torsional pendulum at frequencies near 1 cps. The torsional pendulum was of low thermal inertia and was designed so that specimens could be heated both by a conventional tube furnace and by the joule heating of a separate current through the wire specimen." Use of a static atmosphere of helium gas as a quenching medium made it possible to cut the specimen current, rapidly cool the specimen to the measurement temperature, and make a measurement of the internal friction in less than 1 min. Because of the large solubility of vanadium for nitrogen, the internal friction peak heights were in some cases greater than Q-1 = 0.1. This high damping resulted in an estimated relative uncertainty in the damping measurements of approximately 10 pct. X-ray analyses made to identify the precipitated ni-

Jan 1, 1970

By R. F. Hehemann, S. T. Zegler

The w phase in zirconium alloys containing more than G pct Nb can form in a difjUsionless manner during quenching or with composition change during aging at temperatures below 550°C. The latter treatment establishes a metastable equilibrium between an w phase containing 5 pct Nb and a ß phase containing 45 pct Nb. The superconducting transition temperat~ire of quenched Z?-10 pct Nb and Zr-15 pct Nb alloys is increased by aging at 375°C and both alloys exhibit the same Tc after prolonged aging. The superconducting transition both in the quenched and in the aged alloys is relatively sharp (occurring ovev a temperature range of <0.5°K), and is interpreted in terms of the microstructure that characterizes the ß-w) mixture and proximity effects postulated for thin-film superconductors. At elevated temperatures alloys of the transition elements from groups 4 to 6 in the periodic table exhibit wide ranges of mutual solubility in the bcc structure. Except for compositions that are high in a group 4 element? the bcc structure can be retained at room temperature by quenching and several systematic studies of the influence of composition on superconductivity in bcc alloys have been reported.&apos;&apos;2 The high-temperature bcc form (ß) of the group 4 elements—titanium, zirconium, hafnium—is not retained upon quenching but instead transforms marten-sitically to the hcp structure (a). The Ms temperature can be lowered by alloying the group 4 metals with a solute from a higher group and with a critical amount of solute the martensitic transformation can be suppressed. The 3 phase, however, is not retained without modification. Rather, a metastable phase, w (in particular in titanium- and zirconium-base alloys), occurs over a fairly wide range of compositions above that required for suppression of the martensitic transformation.3,4 As in the formation of a, the transformation of ß to w occurs in a diffusionless manner during quenching and the temperature for its initiation (ws) is lowered by increasing solute content. The ws temperature can be well below room temperature and reversibility of the transformation allows w that forms on cooling to low temperatures to disappear again when the sample is returned to room temperature.5 In Zr-Nb alloys the w phase can also be formed during aging at temperatures below 550°c.5 In this treatment, a metastable equilibrium is established between a niobium-rich ß phase and a zirconium-rich w phase. The present study of Zr-Nb alloys was undertaken to examine the influence of microstructure: as controlled by composition and heat treatment, on the superconducting transition temperature, Tc. MATERIALS AND PROCEDURE The alloys were prepared from zirconium crystal bar that was spectrochemically pure except for 30 ppm of Al, 40 ppm of Cu, 100 ppm of Fe, and 1 ppm of each B and Pb. The niobium used was 99.5+ pct pure containing according to the suppliers&apos; (Stauffer Chemical Co.) analysis a maximum of 50 ppmO, 60 ppm of N, 30 ppm of C, 5 ppm of H, 200 ppm of Ta, 50 ppm of Mo, and 15 ppm each of Fe, Co, and Ni. The alloys were prepared in the form of buttons weighing approximately 4 g by arc melting on a water-cooled copper hearth in an inert-gas atmosphere. All alloys were heat-treated in the ß-phase region for 3 days at 1000°C and water-quenched. For heat treatment, the specimens, 0.5 cm in diam by 1.0 cm long, were wrapped in zirconium foil and sealed in an inert-gas atmosphere inside quartz capsules. Quenching was done by breaking the capsules under water. Subsequent aging treatments of Zr-10 pct Nb and Zr-15 pct Nb alloys were done by placing the specimens in a lead bath at 375°C and quenching in chilled brine. The phases present in the quenched and aged alloys were identified by optical and X-ray metallography. X-ray powder patterns were taken at room temperature with a 114.6-mm-diam Debye-Scherrer camera and CuK-a radiation. Superconducting transition temperatures were determined from magnetic-permeability measurements6 in a 10 oe field. The superconducting transition temperature was determined from a plot of galvanometric deflection as a function of temperature by extrapolation of the linear portion of the curve to zero deflection. In Figs. 1 and 3 the arrows indicate the temperature range of the transitions. RESULTS AND DISCUSSION Superconductivity in Quenched Alloys. In Fig. 1 Tc for alloys quenched from 1000°C is plotted against nominal composition. Indicated also in Fig. 1 are results of metallographic studies. Alloys containing less than 5 pct Nb transform martensitically to a during quenching from 1000°C and Fig. 1 demonstrates that Tc increases significantly as the niobium concentration in a is increased. On the basis of the Bardeen-Cooper-Schreiffer theory of superconductivity7 it seems most likely that this increase in Tc results from an increase in the density of electronic states as zirconium is alloyed with niobium. This increased density of states has been revealed clearly in low-temperature specific-heat measurements.8 The martensitic transformation to a is suppressed when the alloy content exceeds 5 pct Nb. In the range from approximately 6 to 30 pct Nb, quenched alloys consist of a mixture of B and w phases and the amount

Jan 1, 1967

By G. Nabi, W-K. Lu

Cylindrical specimens of natural dense hematite were reduced to magnetite at atmospheric pressure in H2-H2O mixtures of known composition over the temperature range 1084° to 1284°K. The rate of reduction was measured by the rate of movement of the interface between hematite and magnetite. The diffusion of gases through the gaseous boundary layer, the magnetite layer, and the interfacial chemical reaction were all considered in the interpretation of experimental data. The mass transfer coefficient through the boundary layer was calculated using accepted correlations. Values of the chemical reaction rate constant and the diffusivity of hydrogen in the magnetite phase were determined. THE present investigation is concerned with the reduction kinetics of natural hematite to magnetite by H2-H2O mixtures in the temperature range 1084" to 1284°K at atmospheric pressure. This reaction is the first step in the series of topochemical reactions in the process of reducing hematite to iron. Kinetic information of the simple steps such as hematite-magnetite transformation is necessary in order to have a better understanding of the complex processes of hematite reduction in iron-making. It also has direct industrial significance because magnetic roasting is one of the most important methods in benefication of lean ore.&apos; Although many technical papers have been published on the process of magnetic roasting and iron oxide reduction, very little information is available in the literature concerning the fundamental nature of hematite reduction to magnetite by reducing gases. Hansen et al.2 reduced the dense synthetic pellets of high-purity oxide in CO-CO2 mixtures and determined the reaction rate by weight-loss method. They were able to interpret most of their results by applying the interfacial area control theory developed by Mckewan.3 In contrast, Wilhelm and St. Pierre,4 who studied reduction of hematite to magnetite in H2-H2O mixtures by weight-loss method, stressed that the resistance of the porous magnetite layer to the diffusion of gases cannot be neglected in consideration of the overall reaction rate. In the present study the contributions of interfacial chemical reaction, diffusion of gases through the magnetite phase, and the gaseous boundary layer to the overall reaction rate will be considered. APPARATUS AND PROCEDURE Hematite Specimens Preparation. Natural hematite ore from Vermillon range of Northern Minnesota was selected for the present investigation because of its high purity and thermal stability. Chemical analysis of five samples gave the following average values: 67.52 pct total iron (96.62 pct Fe2O3, 0.28 pct FeO, 0.03 pct metallic iron), 2.53 pct SiO2, <0.07 pct MgO, 0.03 pct CaO, 0.05 pct combined mixture, 0.07 pct loss on ignition, and 0.34 pct other. Cylindrical specimens of 0.93 cm in diam and 2.7 cm in length were drilled from slabs of ore with a water-cooled diamond core drill. These specimens were heated to 1000°C and furnace-cooled. Specimens with silica pockets developed large cracks. The uncracked specimens were heated a second time, and their surfaces were carefully examined with a microscope. Those with hairline cracks or surface inhomoaenitv-- were rejected. Preparation of H2-H2O Mixtures. H2-H2O mixtures were prepared by the combustion of H2-O2, mixtures in a pyrex glass chamber in the presence of a catalyst. Alumina pellets coated with palladium, supplied by Englehard Industries, were used as the catalyst. Purified grades of hydrogen and oxygen were used which were repurified by usual techniques. Hydrogen before entering the combustion chamber was passed through an activated alumina H2O absorption bulb, with copper turning at the top. The cover of this bulb was not made pressure-tight so that any pressure development in the hydrogen line would cause the cover to blow off and also the copper turnings would act as a flame arrester in the case of a flashback from the combustion flame. Oxygen flow rates were measured with a bubble flow meter after purification with 1 pct accuracy. Hydrogen flow rates were measured by "precision wet test meter" and the amount of unburnt hydrogen was accurately measured by a bubble flow meter, after condensing water vapor in the gaseous stream. The Pyrex glass bulb contained concentric Vycor glass tubes as shown in Fig. 1. Oxygen was prevented from diffusing into the hydrogen line by threading platinum wire through pores at the combustion end of gas inlet tube. The glass bulb was heated with a Kanthal heating wire pasted in asbestos paper. The surface temperature of the bulb was measured with a thermocouple and adjusted to remain at approximately 350°C. The gaseous reaction chamber also served as a preheater for gases to avoid thermal segregation. The following sequence of operation was adopted. 1) Nitrogen was passed through the outer concentric tube to purge the catalyst bulb of oxygen. 2) Hydrogen was introduced through the inner tube until a steady flow was obtained. 3) Oxygen was then introduced into the nitrogen stream passing through the outer tube. 4) When combustion had commenced and a flame was visible over the platinum wire, the N2 was turned off.

Jan 1, 1969

By N. J. Grant, B. C. Giessen, Paul Predecki

ALLOYS of gold, silver, and aluminum with elements of the groups BII, BIII, BIV, and BV were prepared by a rapid quenching technique (splat) and were examined by X-ray diffraction. Five new intermediate phases were found and will be described briefly herein. For the gold and silver systems, the concentration ranges having an electron/atom ratio e/a of 1.4 to 1.5 ("3/2 Hume-Rothery phases") were studied primarily. Master alloys were prepared from high-purity metals (99.9+ pct or better) by melting either in evacuated fused silica capsules or by nonconsum-able-electrode arc melting in an argon atmosphere. Small pieces, 20 to 50 mg, of each alloy were blast-atomized to form a splat, by a technique similar to that described by Duwez and Willens.1 The technique used for this study is described in detail in Ref. 2; it utilizes a resistance-heated graphite crucible with a small hole at the bottom, directed toward a metal substrate or quenching plate. The prepared alloy rests over the fine hole, through which it is expelled by an explosion shock wave in the form of fine droplets (1 to 50 µ) of molten metal onto a copper or silver substrate, which is maintained at about -190°C. The resulting very high cooling rates (see Ref. 2 for quantitative measurements) can prevent the process of nuclea-tion and growth in many instances, resulting in the formation of metastable phases. The splat particles were transferred to a GE-XRD5 diffractometer and maintained at -190°C, where they were examined with CuKa radiation. The samples were then allowed to warm to room temperature or were heated to higher temperatures until the equilibrium structures formed. Of fifteen alloy systems considered, nonequi-librium structures were encountered in six; these are described below and summarized in Table I. In the system Au-Sb a metastable £ phase (A3 type, hcp, a = 2.898 + 0.002A; c = 4.731 * 0.004A; c/a = 1.633) was found in the concentration range Au + 13 to 15 at. pct Sb. This phase is isomorphous with the stable phases in the systems Au-Cd, Au-In, and Au-Sn, all at an average e/a ratio of 1.4 to 1.5. The concentration range of one-phase metastable was deduced from the small amounts of supersaturated gold solid-solution phase present in the splat product. It was found that ? could also be retained by splatting onto a substrate held at room temperature: however, decomposed into the equilibrium phases Au + AuSb2 after heating to 200°C for 1/2 hr, or on holding the powdered splatted alloy at 20°C for several months. Calorimetric measurements will be made in an attempt to decide the question whether ? is metastable at all temperatures or whether it is a stable phase at low temperatures. There is evidence that another phase, possibly also close-packed but with a different stacking sequence, can be obtained by rapid quenching of alloys with a different antimony content. Klement, Willens, and Duwez3 reported the existence of an amorphous phase on quenching Au-Si alloys (25 at. pct Si) to - 196°C. They found that on heating to room temperature another phase of unknown crystal structure was formed. This was confirmed (see Table I); however, the new crystalline phase, designated as ?, could also be formed simply by rapid quenching to room temperature, and even was found to exist already in the as-cast Au + 20 at. pct Si alloy. It was found that ? decomposed into Au + Si on the specimen surface at room temperature. This behavior, and the question whether or not there is an equilibrium-temperature region for ?, have not yet been resolved. It is probable that ? (Au + 20 to 21 at. pct Si) is cubic of the -brass type (D81-3) with a = 9.60, + 0.01A and N = 52 atoms per cell [compare 6 (CU-Sn)4]. Except for two very weak lines, the powder pattern of about thirty lines could be indexed on this basis; however, a determination of the atom positions has not yet been attempted. For Au-Ge the C phase was observed at about 21 at. pct Ge as reported by Luo et at.5 Lattice parameters a = 2.876A, c = 4.73,A, c/a = 1.64 were found. In the Au-Pb system, formation of a ? phase was not observed, but in the lead-rich region at 75 at. pct Pb, broad peaks belonging to an amorphous phase were found. The maximum diffracted intensity occurred at 28 = 32.4 deg which is about 1 deg larger than the position of the (111) line of lead (Cuka). For Ag-Pb, an amorphous phase analogous to the one found in the Au-Pb system was observed; this metastable phase exists probably at about 75 at. pct Pb. Since no lead-rich alloys were tested, all alloys consisted of silver + amorphous phase at -190°C. In A1-Ge alloys, line-rich and complex powder patterns were obtained at about 30 at. pct Ge; they bear similarities to those of aluminum and germanium, but are of lower symmetry; the existence of more than one intermediate phase is possible. The authors are grateful to the Kennecott Copper Corp. for Fellowship support, and ARPA (Contract

Jan 1, 1965

By W. C. Leslie

The textures of cold-rolled and of annealed iron are compared with those of an iron-0.8 pct copper alloy in which the amount of precipitation after cold rolling was controlled. Previously published pole figures -for cold-rolled and for annealed iron are confirmed. The effects of precipztatiotz after cold rolling are to retain the cold-rolled texture after annealing, to inhibit the formation of the usual allnealing texture, and to produce elongated recrys-tallized ferrite grains. It is suggested that the inhibition of new textures by precipitation after cold rolling is a general phenomenon. A great deal of attention has been paid to the development of texture during the secondary or tertiary recrystallization of ferritic alloys, but very little work seems to have been done on the control of texture during primary recrystallization. If such control were attained, it might be possible to simplify the processing of oriented materials or to change the characteristics of current cold-rolled and an-nealed products. From previous experience, it seemed likely that texture could be controlled by recrystallizing a supersaturated solid solution. Green, Liebmann, and Yoshidal found that the formation of preferred orientation in aluminum (40 deg rotation about <111> relative to the deformed matrix) was inhibited when iron was retained in supersaturated solid solution in the strained aluminum. The authors attributed this inhibition to iron atoms in solid solution. There is, however, an alternative explanation. Green et al, took a highly supersaturated solution of iron in strained aluminum and heated it to an unspecified temperature for recrystallization. It is probable that precipitation occurred prior to and during recrystallization, and it is proposed that the inhibiting agent is this precipitate, rather than the iron atoms in solid solution. It is important to note that precipitation before cold work is ineffective; the effective precipitate is that formed after cold working and either before or during recrystallization. The location and distribution of the precipitate are critical. Precipitation in such a manner has been found to have profound effects upon kinetics of recrystallization and the microstruc-ture of the recrystallized alloys.2-4 It would be surprising, indeed, if this were accomplished with no change in texture. Because of the relative simplicity of the system, and because of previous experience,4-7 it was decided to determine the effect of precipitation on texture in an alloy of iron and copper. Bush and Lindsay5 found an unspecified change in texture in cold-rolled and annealed low-carbon rimmed steel sheets when the copper content exceeded 0.1 pct. MATERIALS In earlier work, the rate of recrystallization of a low-carbon steel was greatly decreased by 0.80 pct copper, and, after the proper treatment, the recrystallized ferrite grains were greatly elongated.4 Accordingly, it was decided to investigate the effect of precipitation on texture at this level of copper content. The iron and the iron-copper alloy were made from high-quality electrolytic iron and OFHC copper, vacuum-melted in MgO crucibles, cast, hot-rolled to 0.2 in., then machined to 0.150 in. The compositions are given in Table I. The plates were heated to 925°C and brine quenched, twice. This produced a ferrite grain size of ASTM 0 in the iron and ASTM 1 in the Fe-Cu alloy. Disk specimens were cut from the heat-treated plates, repeatedly polished and etched, then used to determine (110) and (200) pole figures by reflection. Despite the complication of large grain size, these pole figures strongly indicated a random texture. PROCEDURES The copper content in solid solution in ferrite before cold rolling and recrystallization, and hence, the amount that could precipitate during the recrys-tallization anneal, was controlled at three levels by heat treatment. The specimens as quenched from 925° C were presumed to have all the copper, 0.80 pct, in solid solution. Other samples of the quenched alloy were aged 5 hr at 700°C to retain about 0.5 pct Cu in solid solution.6 A third set of quenched specimens was reheated to 700°C, then slowly cooled in steps, to reduce the amount of copper in solid solution to a very low level. All specimens were cold-rolled 90 pct, from 0.150 to 0.015 in. thick. The rolling was done in one direction only, i.e., the strip was not reversed between passes, with a jig on the table of the mill to keep the short specimens at 90 deg to the rolls. The rolls were 5 in. in diameter and speed was 35 ft. per min. Machine oil was used as a lubricant. In a supersaturated alloy, the maximum effect of the copper precipitate on microstructure and on recrystallization can be developed by a treatment at 500°C, after cold rolling and before recrystallization.&apos;

Jan 1, 1962

By R. W. Cahn, C. D. Graham

Two predictions of the oriented growth theory of recrystallization textures have been tested by measuring the orientation dependence of the rate of growth of a single grain into a strained single crystal of aluminum, and determining the orientations of artificially and spontaneously nucleated grains growing preferentially into strained aluminum single crystals. Growth rates are found to be insensitive to orientation, except that new grains with orientations similar to the matrix or to a twin of the matrix have very low mobilities. Similarly, new grains growing preferentially into a strained crystal have random orientations, except that orientations near that of the matrix or its twins are avoided. The predictions of oriented growth theory are thus not confirmed. BASICALLY, the oriented growth theory of re-crystallization textures1 rests on the assumption that the rate of growth of a recrystallizing grain depends strongly on the orientation of the growing grain relative to the strained matrix into which it grows. In particular, the theory holds that in face-centered-cubic metals the orientation which corresponds to maximum growth rate is one in which the growing grain and the matrix are related by a rotation about a common <111> direction. The amount of rotation, as derived from several kinds of experiments,2-1 has been assigned various values, generally in the range between 20" and 40". (A <111> rotation of 60" is a twin relationship.) The conclusion that boundary migration rates depend strongly on orientation is based almost entirely on indirect evidence; there have been very few direct measurements of boundary migration rates as a function of orientation.* " The present investigation was undertaken to provide such measurements, to help make possible a decision between the oriented growth and oriented nilcleation theories of recrystal-lization textures. The basic experimental program consisted of measuring the rate of growth of a single recrystal-lizing grain consuming a strained single crystal, with the orientations of both grains preselected so that the effect of orientation on growth rate could be determined. A prerequisite for such an experiment is a strained single crystal which will support the growth of a new grain but which will not spontaneously nucleate new grains on heating. That is, the crystal must support the growth of a grain nucleated artificially, but contain no recrystalliza-tion nuclei which will become active at the testing temperature. Beck was apparently the first to note that such a condition could exist," and to make use of the condition for am experiment of the type described here.&apos; The present work was actually suggested, however, by a report of Tiedema". " that an aluminum single crystal strip, oriented with a (111) plane in the plane of the strip and a < 112> direction parallel to the tensile axis, would not recrystallize after 20 pet extension even when heated almost to the melting point, provided that the strip was heavily etched before being heated. This result could not be duplicated in the present work. In fact, it was found that any crystal which deformed in multiple slip (<100>, <112> and <111> orientations) underwent spontaneous nucleation after 15 pet extension, even if etched. However, crystals which deformed in single slip, and which did not develop heavy deformation bands, could be extended 15 pet without showing spontaneous nucleation at temperatures up to 600°C. Crystals oriented within about 10o of <110> which developed heavy deformation bands could be extended 10 pet without showing spontaneous nucleation. In all cases a heavy etch was required to prevent nucleation. Etching was necessary because of the presence of an oxide layer on the crystal surface at the time of straining, which leads to preferential nucleation at the surface.&apos;&apos; Grain Growth Rates Experimental Procedure and Results—Aluminum strips of 99.6 pet purity (principal impurities 0.19 pet Fe and 0.12 pet Si), 1 mm by 1 cm in cross section, were grown into single crystals of controlled orientation by the strain-anneal method of Fuji-wara.&apos;"&apos; " A sharp temperature gradient was maintained in the strips during growth by lowering them into a salt bath controlled at 650°C. Crystal orientations were determined by the etch-pit method of Barrett and Levenson" to an accuracy of ±2O. The crystals were extended by 10 or 15 pet in a simple hand operated tensile machine. Crystal orientations were rechecked after extension, and were found to be in agreement with the orientations predicted by the formula of Schmid and Boas." After extension, the grip ends of the single crystal specimen were cut off with a jeweller&apos;s saw, and the crystal heavily etched (at least 20 pet wt loss) in hot 10 pet Na or KOH solution. A region of severe local deformation was then introduced at one corner of the strip, usually by cutting off the corner with shears. Heating this end of the strip caused a large number of new grains to nucleate at the sheared edge. One of these grains grew to occupy the full width of the strip. The appearance of the strip at

Jan 1, 1957

By Jerome J. English, Gordon W. Powell

An experimental investigation and mathematical analysis of the thermal-dilation behavior of the titanium alloy Ti-7Al-3Cb have shown that the linear dimensional changes associated with the polymorphic transformation need not be isotropic. The absolute magnitude of the linear dimensional change, which may be either positiue or negative, associated with the cr-p transformation is dependent upon the relutzve volumes of different orientations of the transformation product. It is hypothesized that the dilation irregulati-ties that have been observed during the polymorphic transformation of pure, coarse-grained titanium and other titanium-base alloys can be explained in the same manner. When titanium is heated above about 165O°F, the hcp a structure transforms to bcc 0. Thermal-dilatioh measurements have shown that the transformation is accompanied by a decrease in length of 0.16 pct.&apos; Such dilation behavior would be expected because the volume of the hcp unit cell is about 0.3 to 0.4 pct greater than that of the bcc unit cell. A recent investigation2 of the thermal-dilation behavior of an experimental a-p* titanium alloy, Ti- 7A1-3Cb, containing 0.06 wt pct 0 showed that its dilation behavior during the polymorphic transformation differed substantially from that reported for unalloyed titanium. The first time the alloy was cycled through the transformation, the dilation curve closely duplicated that of unalloyed titanium. However, upon repeated cycling through the transformation temperature range, both the magnitude and the sign of the dimensional change associated with the transformation were observed to vary with each cycle. This investigation was undertaken to obtain additional data on the dimensional changes associated with the polymorphic transformation in the Ti-7A1-3Cb alloy and to determine the cause of the dimensional irregularities. After testing, the specimens were examined metallo-graphically. In addition, Laue back-reflection patterns were obtained from selected sections taken perpendicular to the specimen axes to determine the a orientations present in these sections. White radiation from a tungsten target and a 0.1-mm-diam collimator were used to produce the diffraction patterns. RESULTS Dilation Curves. Three types of thermal-dilation curves were obtained when the a-8 titanium alloy was heated and cooled through the transformation temperature range. These three types of curves are illustrated in Fig. 1. The type I curve represents what is considered normal behavior, because the dilation change is what would be expected on the basis of the volumes of the unit cells of a and p. The Type I1 curve is the inverse of Type I. Normal behavior is characterized by an expansion on cooling through the transformation, whereas a contraction takes place in the Type 11 curve. With Type ni behavior, no clearly distinguishable length change occurs during the transformation. No other anomalies that might be indicative of other phase transformations were observed in the dilation curves at lower temperatures. Apparently, the cooling rate was low enough for equilibrium to be reached during the 0 to a transformation. Table I lists the types of dilation curves observed during the polymorphic transformation as a function of the direction of measurement and cycle number. The A1 value was determined by extrapolating the low-temperature (a + 5 pct p) and high-temperature (100 pct p) segments of the dilation curves to a common temperature and measuring the difference in the or-dinates at that temperature, see Fig. 1. The transformation occurs over a temperature range in this alloy, so the magnitude of A1 is not an absolute value but depends on the choice of temperature. A mean temperature, T,, within the transformation temperature range was selected for the measurement. T, on cooling occurred about 100°C lower than T, on heating. The first time each of the three dilation specimens was heated to above the temperature, that is, Cycle 2, normal Type I behavior was observed. In Cycle 3, two deviations from normal behavior occurred. First, during cooling of the longitudinal specimen, a substantially larger expansion, +0.21 pct, was measured as 0 transformed to a compared with +0.03 pct in Cycle 2. Second, the thickness specimen was observed to undergo a contraction instead of the anticipated expansion on cooling. Continued cycling of the three specimens from room temperature to 2500°F produced additional changes in the dilation behavior. These changes did not seem to be related to the fabrication direction of the alloy because the values of a1 for the longitudinal, transverse, and thickness specimens varied unpredictably in magnitude and sign. Furthermore, both the longitudinal and transverse specimens showed all three types of dilation curves at least once during the six cycles that they received. Fig. 2 is a sketch of the transverse specimen after

Jan 1, 1967