Search Documents

By L. E. Paulson

INTRODUCTION The Northern Great Plains has 16 billion tons of strippable lignite (1). Presently, 15 million tons per year are mined; essentially all is used for generation of electrical power. In the future, additional large quantities will be consumed in the production of gaseous and liquid fuels. A major consideration in design and operability of power stations and conversion plants is the nature of the ash or inorganic constituents of the lignite used. These inorganic components cause fireside fouling in boilers, exert a catalytic effect in liquefaction and gasification, and contribute to particulate and SO2 emissions. Ash fouling on fireside boiler tubes cause reduced heat transfer and gas flow which limits boiler performance. Severe fouling can result in shutdown of the boiler. A comprehensive test program in both pilot plant and field studies at the Grand Forks Energy Technology Center (GFETC) has shown that ash fouling increases with increased sodium content of low-rank coals (2). The sodium in the coal can be

Jan 1, 1983

By L. Bruce McRae

A programme of work was initiated so that the possibility for the agglomeration of Transvaal chromite-fines by pelletization could be investigated. The use of cementitious binders did not yield promising results, binder additions of up to 10 per cent failing to produce an agglomerate that would be suitable as feed for an electric-smelting furnace. Further laboratory and pilot-plant studies showed that high-quality pellets could be made from chromite bonded with small amounts of bentonite and hardened by heat treatment at temperatures of the order of 1000°C. An investigation was also done into the reduction behaviour of pellets containing amounts of stoichiometric carbon up to that required for complete reduction. The results showed that the maximum degree of reduction that could be obtained was approximately 75 per cent, and that these pellets had the physical properties that would make them amenable to smelting in a submerged-arc electric-smelting furnace.

Jan 1, 1977

By Frederick Prime

AT the last meeting of the Institute, Mr. A. L. Holley read a paper on "Steel," in which he proposes for it a definition so opposed to the one generally received, as to call for some remarks. Until within the last five or six years there has been no dispute on the subject, and it seems worth while to investigate the matter. For not only does a proper tax on all importations depend on a proper appreciation of the term steel, but it is necessary to know whether steel, or wrought-iron, or homogeneous iron are requisite in all processes of manufacture in which malleable iron is employed, on account of cost, strength, etc. Karsteu* says : " Iron may be obtained, either as an unforgeable, unweldable metal, which melts at a high heat, termed cast-iron; or as a ductile, weldable, soft metal, which can only be melted at the * Karsten, Handbuch der Eisenhüttenkunde, 3d ed., vol. i, p. 6. Berlin, 1841.

Jan 1, 1876

By John R. Dyni

Colorado nahcolite deposits, estimated at 29 Gt, formed in an asymmetric permanent-lake basin whose waters were rich in algae and sulfate-reducing bacteria. Nahcolite (NaHCO3) occurs in oil shale of the Green River Formation (Eocene) as aggregates (62%), disseminated crystals (24%), and impure beds (13%). Because much of the nahcolite is nonbedded, it will be mined with oil shale and can be concentrated to marketable grade by crushing and screening. Impurities in nahcolite are kerogen, quartz, pyrite, and carbonate minerals. A promising new market for nahcolite is in the process of removal of sulfur dioxide from industrial stack gases. When heated, nahcolite reacts with sulfur dioxide to form sodium sulfate. Differences in thermally induced microporosity may explain why nahcolite is more reactive than trona, a Possible competitor with nahcolite for SO2 removal. Limited production of nahcolite at one or possibly two localities is expected in the next several years, but large-scale production is probably at least 10 years away.

Jan 1, 1982

By Patrick M. Hurley

The relationships between mineral deposits and various plate margin mechanisms are examined under the constraints of radiogenic isotopes and other geochemical indicators. It seems like1 y that: (1) deposits of the spreading ridge association are fairly ubiquitious through most of geologic history and can be recognized by the lithologic assemblage and primitive lead isotope ratios; (2) most metals in the island arc association are not derived entirely from a subducting oceanic plate, and have a partly continental affinity; (3) subduction beneath a continental plate generates ores which are derived either from the downgoing plate or from the lower crust; (4) the heating of a continental plate by thickening or by mantle plumes may develop a metallogenic province involving extraction of metals from the curst; (5) rifts and grabens developing thick sections of marine sediments with evaporites may be the locus of base metal mineralization by movement of reducing brine solutions resulting from diagenesis and bacterial reduction of sulfates

Jan 1, 1978

By J. Y. Oldshue

INTRODUCTION The field of fluid mixing involves many different kinds of process objectives. In order to classify these objectives, Table 1 gives a listing of five basic application categories, gas-liquid, liquid-solid, liquid-liquid, miscible liquids, and fluid motion. However, each of these areas can be broken up into two different concepts one involved with uniformity of solids or liquids as a criteria, and the other involved with chemical reactions or mass transfer. The things that we would do to design a fluid mixing for solid suspension are quite different from things that we would do to design a mixer for heat transfer or gas-liquid mass transfer. Therefore, there are really ten separate mixing technologies. Each of these areas has its [ ] own principles of fluid mechanics, scale-up techniques and application experience. We will take a look at each of these areas and look at some of the ways that we can handle fluid mixing applications which.

Jan 1, 1979

By R. C. Dalzell, A. E. Wells

In 1866, Thomas Graham1 called attention to the volume of gases, three times the volume of the sample, evolved from a meteoric iron heated in an evacuated porcelain tube. From that time to this the occurrence and significance of gases in metals have been the subject of investigation by many workers, among whom Sieverts,2 Iwasé3 and 0. W. Ellis4 stand preeminent. Sieverts and Iwasé concerned themselves with the solubility of a number of gases in metals in the liquid and solid states. They determined the absorption coefficients of these gases, and in all cases found a sharp change in solubility at the melting point of the metals. Ellis analyzed the gases evolved by solidifying copper and those occluded by the solidified metal. Lobley and Jepson5 endeavored to determine the effects of hydrogen, carbon monoxide and nitrogen on the porosity of copper that was allowed to solidify in the presence of each gas after 30 min. exposure to it in the

Jan 1, 1930

By Eugene Stebinger

PAGE Introduction.............. 890 Position oF Montana in the Western Coal Province*..... 890 Montana's Total Coal Tonnage.........891 THe Coal-BearINg Formations,........891 General Statement............. 891 Kootenai Formation............ 895 Eagle Sandstone............896 Judith River Formation............ 896 Homethief or Lennep Sandstone.........897 Lance Formation..........• 897 Fort Union Formation............ 898 Tertiary Lake Beds............. 899 Distribution of the Coal Fields.......... 899 Classification of Montana Coals.........900 General Statement............. 900 Comparison of Chemical Analyses and Heating Values..901 DESCriPTions of the CoaL Fields.......... 905 • Fields Containing Bituminous and Higher Grade Coals..905 Bridger Field............. 905 Stillwater Field............ 906 Electric Field............ 907 Trail Creek Field...........908 Gallatin Field............909 Lombard Field...........910 Great Falls Field............ 910 Lewistown Field............ 911 Valier Field............. 912 Blackfoot Field............ 913 Fields Containing Sub-bituminous Coal.. 913 Bull Mountain Field..........913 Red Lodge Field............ 914 Missoula and Drummond Fields......... 916 Milk River Field............ 916 The Eastern Plains Region of Lignite and Sub-bituminous Coal.... 917

Jan 1, 1914

By H. O. Hofman

In the blast-furnace smelting of lead, copper and other non-ferrous metals, the largest part of the product obtained is slag. Its formation consumes more of the heat-energy of the fuel charged than any other chemical reaction that takes place. It is therefore of importance to know at what temperatures the different slags will form, so as to be able to choose in a given case the slag that will form at the right point in the operation, will keep the products thoroughly fluid, so as to insure a satisfactory separation, and will permit the consumption of fuel to be reduced to the lowest practicable point. While practical experience has brought out in a general way the leading differences as to the formation-temperatures of Rome silica—iron —lime slags, accurate details are still wanting. The object of the investigation here described was to supply some of these.* Prominent among the men who have worked on the fusibility of silicates are Lampadius, † Sefström,‡ Berthier,§

Jan 1, 1900

By L. L. Wyman

SINCE the observations of Heyn,1 relative to the embrittlement of copper after having been heated in hydrogen, this subject has received considerable attention from later investigators. The published works of Archbutt2 and of Bengough and Hill3 give the reasons for this embrittlement-the formation of steam by the reaction between cuprous oxide and hydrogen. From Ruder,4 Pilling,5 Moore and Beckinsdale,6 Bassett and Bradley,7 and from Smith8 can be obtained quantitative data concerning the action of hydrogen and other reducing gases on copper samples having various oxygen contents. This problem has been discussed from a practical standpoint by Fuller9 who calls attention to some of the instances of this embrittlement encountered in the manufacturing field. The examples he cites may be considered typical cases of copper embrittlement which were incident to the process of manufacture. In many cases, such difficulties are overcome by changes in the manufacturing process.

Jan 1, 1931

By W. S. Ayres

The construction of a new breaker at the Cranberry Colliery, Hazleton, Pa., was forced upon the operators, A. Pnrdee & Co., by a fire which destroyed the entire plant early in January, 1896. The loss included, in addition to the breaker, three boilerhouses and three engine-houses. The boilers were not injured, but the steam-pipes and connections were all broken and warped by the fire. The boilers were probably saved from injury by the presence of mind of the fireman., who started all his feed-pumps and filled the boilers with water. The hoisting-engines were more or less warped and cracked, but by patching and replacing the injured and broken parts, they were made to do satisfactory service in the new plant. It may be worthy of mention that the wrought-iron shaft of one of the hoisting-drums, 12 inches in diameter by 17 feet long, was so heated in the fire that the weight of the drum caused it

Jan 1, 1899

By R. S. Archer

THE binary aluminum-silicon alloys have certain characteristic advantages which are now well known, and these alloys have come into considerable use during the past several years.1 Their field of application has been limited to a certain extent, however, by their low yield point and hardness, low endurance limit, and relatively poor machining characteristics. These properties are improved by the addition of copper, and the ternary aluminum-silicon-copper alloys constitute an important class. The addition of copper decreases the corrosion resistance of the aluminum-silicon alloys and increases specific gravity. Magnesium is a hardening addition which seems to have relatively little effect on corrosion resistance, and which, of course, reduces specific gravity. The object of the work described in this paper was the development of alloys and heat treatments for the production of sand castings and permanent-mold castings having substantially all the advantages of the binary aluminum-silicon alloys together with mechanical properties improved to a degree permitting wider application.

Jan 1, 1930

By G. Sachs

THE iron-rich iron-nickel alloys have at-tracted considerable academic interest in recent years. The carbon-free alloys are of minor practical importance, but they are Atomic per cent nickel FIG. I. FIG. 2. FIG, I.-HONDA'S AND MERICA's IRON-NICKEL DIAGRAM, FIG. 2.-MARSH'S IRON-NICKEL CONSTITU-TIONAL DIAGRAM. the base of many alloys with various out-standing properties. The iron-nickel alloys, therefore, have been investigated exten-sively regarding both their structures and their properties. The researches on these alloys up to 1938 have been collected and critically reviewed by J. S. Marsh,1 and will be discussed in some detail in the sec-tions of this paper dealing with specific subjects. These numerous investigations have not succeeded in establishing the equilibrium conditions in this system. Alloys containing more than a certain amount of nickel (8 to10 per cent Ni) undergo the allotropic transformation extremely sluggishly, both on heating and cooling, showing a large hysteresis,2 which is not dependent upon

Jan 1, 1940

By J. Spotts McDowell

INTRODUCTION The magnitude of the thermal expansion of silica brick, and its inability to withstand rapid temperature changes, present problems of considerable importance in the manufacture of siliceous refractories. In the study represented by the experimental data herein described, these problems are considered from the point of view afforded by the results of recent investigators: Fenner and his associates of the "Geophysical Laboratory, Washington, D. C., who have established the stability relations of the silica minerals, and Endell and co-workers in Berlin, who have studied the changes brought about in the constitution of siliceous refractory materials upon the application of heat. In the process of manufacture, the quartzite from which the brick is made changes in part into cristobalite and tridymite. The attempt is herein made to determine by microscopic methods the degree of transformation in various specimens of test bricks manufactured at slightly varying temperatures of burning, with varying coarseness of grain, and to determine the effect of repeated burning. The effect of variations

Jan 10, 1916

By J. H. Anderson, G. A. Parks, B. K. Jindal, H. Leslie Bullock

H. Leslie Bullock (Engineering Consultant, Oak Park, 111.) — In reading over the paper, I find that I have no quarrel with the thoroughness of investigation of the points studied, but I am forced to question the selection of oxides from oxides as the subject of the investigation, the inclusion of silica gel as an example, and to question the validity of some of the conclusions. Separation of oxides from oxide, in minerals where the liberation of values is possible by grinding, are comparatively rare. Most oxides are only slightly soluble and the action of carbon dioxide or other acid forming ingredient in the air must be added to humidity to produce surface action. Silica gel is a very special synthetic substance in which the adsorption is determined by total surface, pore dimensions and temperature. Quartz is our most prevalent oxide and its action in electrostatic separation is far more sensitive to its three thermal transition points than to humidity.

Jan 1, 1968

By W. E. STOKES

A GENERAL extension and appreciation of the stereocartographic principle of precise mapmaking is evident. Under the stimulus of war, many radical improvements in aerial photography, and in airplane and motor con? struction are indicated for the future. A survey of advanced military designs points to the conclusion that the familiar radial motor is destined for oblivion under the impact of the inverted "V" type.' The latest German inverted "V" design of 1000 hp. is 68 in. long whereas British and American motors of the same power are 72 and 94 in. respectively, suggesting a horsepower-weight efficiency ratio in favor of the former. Application of the pressure cooling principle has made possible the development of in-line air? cooled engines which offer many advantages, such as small frontal area, unobstructed vision for the pilot, freedom from vibration because rotative speeds are not limited by fundamental unbalance of reciprocating parts, freedom from excessive bearing loads, and less weight per horsepower.

Jan 1, 1940

By G. K. Dumbauld, B. E. Morgan

A satisfactory well-cementing composition must retain its fluidity long enough to be pumped into Place; then it must develop within a reasonable length of time sufficient strength and impermeability to anchor the casing in position and to form an effective seal between the casing and the formations. These properties may be evaluated by pumpability, strength (compressive or tensile), and permeability tests. Laboratory test procedures for the determination of pumpability time and strength development have been outlined previously and are readily available,1 but a satisfactory and convenient laboratory procedure for the measurement of the permeability of set cement has not been developed heretofore. some permeability data have been obtained previously by passing air through dried cement specimens.2 such a procedure is unsatisfactory because the drying of set cement alters it physical and chemical properties and subjects it to conditions dissimilar to well conditions. A more realistic method would be one wherein the cement remains water-saturated durin

Jan 1, 1952

JAMES ASHWORTH, Livingstone, Alberta, Can. (written discussion*).-About the year 1878, the writer commenced to experiment on safety lamps, the results of which will be found in the Transactions of the North of England Institute of Mining and Mechanical Engineers 1879-1880, the Transactions of the Manchester Geological and Mining Society, and in the technical press. He has also made a careful investigation of the flame caps produced by chemically prepared methane when mixed with air in accurately measured percentages. Before the conclusion of these experiments he personally fitted the hydrogen gas test to a special pat-tern of the Ashworth-Gray patent safety lamp. Later, as pure hydrogen gas was not always available, the writer constructed a safety lamp that would separately burn oil and alcohol; and still later, a somewhat similar lamp to burn alcohol only for specially testing low percentages of methane. This lamp was known As the Ash-worth alcohol safety lamp.

Jan 12, 1919

By Whitmell J. Smithwick, Charles E. Dandois

The first operating unit of the ring or annular shaft kiln as developed by Mr. Karl Beckenbach of West Germany was rated 185 tpd and was installed in 1962. Today, there are approximately 84 units in operation in Western Europe and Japan. Twenty-one additional units are under construction or on order. Sizes range from approximately 100-330 tpd, however, units of over 500 tons are in the design stage. The ring shaft kiln is a single vertical cylinder to which are attached the required service platforms, combustion chambers, injectors and distribution piping (Fig. 1). Auxiliaries such as recuperator, exhaust fan and dust collector are mounted on the appropriate service platform. The charging pan, feed conveyor, etc., are mounted at the kiln top and at the bottom of the kiln is the silo with a vibrator type discharger. Mounted separately is the required blower for injector air and fan for internal cooling.

Jan 4, 1973

T. M. Morris (Measurement and Evaluation of the Rate of Flotation as a Function of Particle Size, P. 794), was the commanding officer of a patrol craft charged with guarding Aleutian waters against infiltration by the Japanese during World War II. Before going into service, he was an assistant research engineer with Anaconda Copper at Anaconda, Mont., and later a metallurgist with Tennessee Copper Co. Presently he is a professor in the Department of Metallurgy, Missouri School of Mines, Rolla, Mo. A member of the AIME, he is a graduate of Columbia University and the University of Missouri, with a Bachelor of Science, Master of Science and a Ph.D. Professor Morris is the author of a previous paper for the AIME, Measurement of the Equilibrium Forces Between an Air Bubble and an Attached Solid in Water. An outdoor man by predilection, he enjoys bird watching and hiking in his free time.

Jan 1, 1952