Search Documents

F. W. Gordon, Philadelphia, Pa.: There can be no objection to the use of cross-compound blowing-engines; and when they are condensing they are susceptible of great range of duty with slight loss in efficiency. By those who have use for the full heat of the waste gases, this type of engine is advantageous; but many furnaces are not so located. The pig-iron is their finished product, and the gases are to be employed only for furnace-use. In this case simple engines are preferable, being less expensive and having less parts to take care of. These reasons determined the introduction of the engines, a sketch of which is distributed at this session. There are three of these engines to furnish blast for two furnaces, for a make of abont 250 tons per day, using 75 per cent. anthracite and 85 per cent. magnetic ores; and they are expected to blow up to twenty pounds pressure per square inch. For blast-furnaces I prefer the single to the coupled engine, except

Jan 1, 1894

By D. J. Dunn, J. L. Huiatt, T. E. Norman

Corrosion studies in laboratory ball mills and grinding environment simulations produce corrision rates and total metal removal rates much lower than those recorded in operating production ball mills. The corrosion component of ball metal loss in many mills probably represents less than 10% of the total loss, judging from AMAX experience and recent US Bureau of Mines (USBM) tests. Such small absolute losses are consistent with ball metal loss measured in production ball mill marked ball wear tests to determine effects of corrosion and abrasion resisting properties of alloys in operating mills. These indicate that metal hardness and microstructure determine relative metal loss rates of a given situation. The combination of ore characteristics and grinding process dynamics determine metal loss severity. Alloying for corrosion resistance and modification of the milling corrosion environment yield relatively small metal loss reductions. Alloying and heat treatment to produce high hardness and microstructures of high carbon martensite and, for cast irons M7C3 carbides, produces the lowest metal losses in typical wet grinding applications.

Jan 1, 1986

By M. J. Pool, R. K. Saxer, J. R. Myers, D. S. Dickson

ThE equilibrium phase diagram of the Mo-Cr system, described by anssen,' indicates that chromium and molybdenum form a continuous series of solid solutions above 1673K. The liquidus and solidus have been reported to have a minimum at about 12 at. pct Mo and 2133°K by Bloom and Grant2 and by Putnam, Potter, and Grant.3 X-ray studies by Trzebiatowski and ploszek4 and Baen and Duwez' revealed no indication of solid solution decomposition after long anneals at 1473", 1273", 923", and 873°K. However, Bloom and rant' by means of cooling and heating curve analysis of alloys containing up to 45 at. pct Mo found thermal effects at temperatures approximately 100" * 30°K below the liquidus. The only previous thermodynamic study of the Cr-Mo alloy system was made by Laffitte and Kuba-schewski6 who used the Knudsen effusion method at 1471°K. These investigators reported the possibility of a miscibility gap because they observed positive deviations from ideality in their chemical activity

Jan 1, 1970

By Raja V. Ramani, Ralph W. Barbaro

This paper presents an application of a Mixed Integer Programming (MIP) model to the problem of locating a centralized coal preparation plant and determining the production schedule for the mines. The system used for illustrating model application is hypothetical but realistic. It consists of three mines, two potential preparation plant sites, heavy media processing plant, and one market. The goal is to maximize the total profit of the system while satisfying the coal delivery schedule over a three year period meeting both quantity and quality requirements (ash, sulfur, and heat content). In addition to the base case, four different scenarios are analyzed. These four modifications are: (1) removing the flotation circuit from the preparation plant and sending all of the fines directly to the clean coal, (2) lowering the quality of coal from one of the mines, (3) applying discounts to the unselected site to improve its competitive position, and (4) adding a new mine. A detailed discussion of the base case and the effect of these four alternatives is presented.

Jan 1, 1983

By V. J. Decarlo, J. J. Gilman

POLISHING pure zinc differs somewhat from polishing less reactive metals. The problem is not that of finding a suitable reagent, but rather of producing the polish in such a way that the surface remains polished after it is removed from the polishing bath. In other words., the anodic film that is vital to the polishing mechanism' must be tightly adherent and nonporous. It is usually desirable that it be thin. Polishing solutions consist of proper proportions of an acid and a strong oxidizing agent. In electro-polishing, the external circuit acts as the oxidizing agent. The proportions are critical because the essential surface film must be maintained at approximately constant thickness during the polishing process. In the case of zinc, chiefly two oxidizing agents, chromic and nitric acids, have been used. The simplest polishing reagent is concentrated nitric acid. However, it has certain disadvantages. It tends to pit: an excessive amount of heat is evolved during polishing; and the oxide film that it produces is not very stable, so that the polished sur-

Jan 1, 1957

By David L. Rife

Fluid inclusions have been studied since the mid-1800s. In 1858, the famous English geologist H. C. Sorby, stated that ". . . there is no necessary connection between the size of an object and the value of a fact, and that, though the objects [inclusions] ... are minute, the conclusions to be derived from the facts are great."' This statement philosophically emphasizes why fluid inclusions should be studied. Fluid inclusions supply the economic geologist with "hard" data on the chemical environment and mechanisms of transport for ore fluids. Such studies enable geologists to understand more about their complex nature. The information that can be obtained from fluid inclusions is as follows: 1) Fluid inclusion "filling temperatures" measured with the microscope heating stage, reflect the hotness of an ore fluid at the time of its entrapment and are one of the most accurate methods of geologic thermometry. 2) Ore fluid densities indicate the extent to which ground water becomes mixed with ore fluids. Density is determined from the composition of inclusions, the ratios of gas to liquid (at room temperature), and from

Jan 1, 1973

By R. E. Reed, R. D. Leggett, Paxton, H. W.

TECHNIQUES have been developed for growing monocrystals and bicrystals of Fe-20 Cr, Fe-20 Cr-20 Ni, and Fe-18 Cr-8 Ni alloys by both the strain-anneal and the Bridgeman techniques. None of the techniques are new but since they are simple and many people have expressed interest, they are described here quantitatively as they could be modified for other single-phase "commercial" materials of high melting point. CRYSTAL GROWTH BY STRAIN ANNEAL Flat tensile specimens with a tapered gage length were initially studied to deduce the approximate critical strain. Normal flat tensile specimens were then used. The optimum procedure for the austenitic steels (Fe-Cr-Ni) deduced from a variety of cold reductions, recrystallization treatments, tensile strain, and growth anneals was as follows: cold reduce 70 pct, recrystallize (after machining tensile specimens) at 1000°C for 1 hr, strain in tension 2.5 pct, and then heat to 1350°C as rapidly as possible. A time of 100 hr at 1350°C is usually sufficient to pro-

Jan 1, 1960

By P. D. Merica

Certain compositions of the light, i:e., aluminum-rich, alloys of aluminum with magnesium and copper have become quite well known within the past ten years under the name of duralumin. These alloys are used for rolling and forging and can be so treated as to develop quite remarkable mechanical properties. Thus a properly heat-treated alloy containing about 4 per cent. of copper and about 0.5 per cent. of magnesium, rolled into sheet or rod, will have a tensile strength of approximately 55,000 lb. per sq. in. (3866 kg. per sq. cm.) with an elongation in 2 in. (50.8 mm:) of about 15 per cent. This alloy, duralumin, was developed by Wilm,1 and its properties more fully described by Cohn.2 The authors considered it worth while to investigate the mechanical possibilities of the light alloys of two somewhat analogous ternary series; namely, of aluminum-magnesium-nickel and of aluminum-magnesium-manganese, to study the effect of variation of composition upon mechanical properties within the alumimum-rich group of the aluminum-magne-

Jan 7, 1919

By C. W. Vaupell

THE Huitzuco mines lie in north central Guerrero, Mexico; production has been about 90,000 flasks of quicksilver since 1873. Near-surface ores fill extinct mud geysers and the deep deposits are chambered veins, stock-works in brecciated blocks, and replacements in limestone. The epigenetic minerals livingstonite, stibnite and sulphur occur in limestone, gypsum and dolomite through a developed vertical range of 260 meters. The deepest workings expose an increased amount of stibnite, which probably indicates that the lower limit of mercury mineralization is being approached. A resur-gence of heat and water formed geysers over an extended area after the period of mercury mineralization. Mud geysers, which are situated, in the outcrops, contain the secondary mercury minerals, cinnabar and barcenite in the gravel and mud filling the vents. A 150-ton flotation plant is in operation concentrating stope fills that assay 3.0 kg. of mercury per ton. In one open stope, which is more than one hectare in area and 60 m. high, 150,000 tons are available.

Jan 1, 1937

By E. Buehler

THE floating zone refining technique'-4 has provided a new experimental approach to the purification of many reactive materials especially those with high melting points. The method avoids the use of a crucible and at the same time it provides a favorable environment at the freezing interface for the growth of single crystals. The physical properties of refractory metals such as molybdenum and tungsten have long been of interest from a fundamental point of view and because of their widespread use in vacuum electronics. Single crystals are often desirable for study. Prior to the introduction of zone melting, single crystals of these metals were usually grown in the solid state at temperatures slightly below the melting point by strain annealing3 or by the application of a moving temperature gradient. Such techniques were mostly successful on wires, ribbons, or rods having small cross-sectional areas. Recently, larger samples of tungsten, molydbenum, tantalum, columbium, and rhenium were melted by a floating zone process which employed electron bombardment heating.10 Single crystals were obtained in many instances

Jan 1, 1959

By P. D. Merica, A. N. Finn, R. G. Waltenberg

CeRtain compositions of the light, i.e., aluminum-rich, alloys of aluminum with magnesium and copper have become quite well known within the past ten years under the name of duralumin. These alloys are used for rolling and forging and can be so treated as to develop quite remarkable mechanical properties. Thus a properly heat-treated alloy containing about 4 per cent. of copper and about 0.5 per cent. of magnesium, rolled into sheet or rod, will have a tensile strength of approximately 55,000 1b. per sq. in. (3866 kg. per sq. cm.) with an elongation in 2 in. (50.8 mm.) of about 15 per cent. This alloy, duralumin, was developed by Wilm,1 and its properties more fully described by Cohn.2, The authors considered it worth while to investigate the mechanical possibilities of the light alloys of two somewhat analogous ternary series; namely, of aluminum-magnesium-nickel and aluminum-magnesium-manganese, to study the effect of variation of composition upon mechanical properties within the alumimum-rich group of the aluminum-magne-

Jan 1, 1921

By D. W. Breck

Zeolites were first recognized as a new group of minerals by Cronstedt with the discovery of stilbite in 1756. The word zeolite was coined from the two Greek words meaning "to boil" and "a stone" because of the loss of water when heated in the mineralogist's blowpipe (Breck, 1974). In 1845 it was discovered that certain soils lave the power of retaining ammonium salts Way, 1850). These were the first ion exchange experiments. Later it was discovered that it was the hydrated silicates in the soil that produced this phenomenon. Several years later a paper was published dealing with the action of dilute salt solutions on silicates which showed that this base-exchange principle, which we now call cation exchange, is reversible. The quantitative cation exchange behavior of zeolite minerals, such as chabazite, was studied. As a result any aluminosilicate which exhibited the property of ion exchange was referred to as a "zeolite," even today the term has been applied to clay minerals as well as synthetic organic ion exchange resins.

Jan 1, 1975

By R. G. Robins, O. J. Kwok

The application of chemical thermodynamic theory to high temperature aqueous systems is discussed as a basis for the explanation of thermal precipitation. The derivation of high temperature potential/ pH diagrams is briefly outlined in order to show a temperature/pH relationship for hydrolytic precipitation, which is an effect that is caused simply by heating an aqueous solution. Various examples of thermal precipitation are given, with particular reference to separation of metal values from leach solutions. Metal sulphate solutions are shown to precipitate basic sulphates, hydrated sulphates , oxides, hydroxides, and oxydroxides of the metal depending largely on the pH, the concentration of metal ion, and the concentration of sulphate or bisulphate. The CuS04-H2S04-H20 system is treated in some detail, and the separation of copper from other metal ions is investigated. Other separations involving Fe, Ni, Zn, Cd, and Cr are considered. Other advantages of thermal precipitation, such as the formation of high purity, large particle size and easily filterable materials, are presented. The kinetics of thermal precipitation are also briefly examined.

Jan 1, 1973

By T. B. Gyles

Zinc is made by the National Smelting Co. and its associates by both the horizontal retort process and the vertical retort process developed by the New Jersey Zinc Co. This paper deals only with the horizontal retort practice at Avonmouth. That the horizontal retort process does survive in all countries in some form or other is due to at least partial success in overcoming some of the inherent difficulties of the process. The horizontal retort furnaces ran into considerable difficulties when the product of the selective flotation of mixed lead and zinc ores became the normal material for treatment. It is necessary, therefore, to make some reference in connection with the process to the preliminary treatment of the ore prior to distillation.. Therefore we include some small reference to this aspect in our description. Furnace Design and Structure Of the types of furnaces in operation at the company's various works, those at Avonmouth are perhaps more typical of the trend to utilize large units, with a subsequent saving in costs, such as heating and supervision.

Jan 1, 1937

By S. Ramachandran, R. A. Walsh, J. C. Fulton

A method has been developed for calculating the oxygen content of commercially melted stainless steels. Application of thermodynamics to the de-oxidation reaction in straight chromium and Cr-Ni stainless steels has resulted in a set of equations DURING the past 30 years, many rewarding developments have resulted from the application of physical chemistry to steelmaking. A need still ex- which permits the calculation of oxygen contents. The model was programmed for computer calc~ilations. The validity of the method was demonstrated on routine oxygen samples from numerous commercially melted heats of stainless steel. ists for further progress in the use of thermodynamics to meet the more stringent requirements for cleaner steel. Current electric furnace practices have been developed around minimizing residual-oxygen content, one of the most important factors controlling the inclusion content of stainless steels. The residual oxygen is controlled by the use of deoxidizers during the finishing period and a number of empirical rules have been evolved. Although this feature of electric furnace practice has long been in use, only in recent years has funda-

Jan 1, 1963

By George E. Beavers

It is well to understand at once that converter gas is always mixed with copper blast-furnace gas at Copperhill before entering the Glover tower, and, at times, roaster gas is also added along with the converter and blast-furnace gas. Fig. 1 is introduced to show the variations in the sulfur dioxide content of the gas and the ability of the acid-plant operator to control the variations, resulting in a very even grade at the Gay-Lussac tower entrance. The sulfur dioxide content of the gas entering the Gay-Lussac tower must be low and regular to assure low niter consumption. The blast-furnace gas alone is rather uniform as regards sulfur dioxide content and the variations, as shown in Fig. 1, are chiefly caused by converter changes—out for charging, slag pouring, copper pouring, and, of course, the "finish." The combined gas during the converter finish is, at times, almost free of oxygen and the sulfur dioxide content reaches 13.0 per cent. At such times air is added at the Glover tower.

Jan 1, 1934

By J. B. Scuffham, G. A. Rowden

The use of ammonia as a leaching agent has been well-documented but only recently have its advantages been fully exploited on a commercial basis. When compared with conventional sulfuric acid leaching processes, the major advantage of ammoniacal systems is their ability to reject iron and many acid consuming gangue materials. Although metallic copper, nickel, zinc, etc. are dissolved rapidly in ammoniacal liquors at ambient temperature in the presence of air the sulfide ores of these metals are more resistant to this treatment. Sherritt Gordon Mines in Canada treats sulfide concentrates at its Fort Saskatchewan plant under pressure with ammoniacal am- monium sulfate solution to solubilize the non-ferrous metal values. Typical leach operating conditions are 80-95°C and 115- 128 psig. Although the metals present in the ammonical solution could be recovered via solvent extraction techniques, Sherritt Gordon Mines currently operates a pressure reduction process using hydrogen to yield metal powders directly from the ammoniacal solution. The basic Sherritt Gordon technology has been applied world wide for the treatment of nickel/cobalt concentrates.

Jan 12, 1973

By Leonard Waldo

(New York Meeting, February, 1911.) THE recent and rapid development of the physics of engineering materials at temperatures as low as that of liquid air and as high is that of the electric are, has drawn renewed attention to the absence of tables, properly printed and spaced, for the convenient and accurate translation of temperature from centigrade to Fahrenheit scales and vice versa. It is to be noted that the Fahrenheit scale is the almost universal usage in foundries and shops in the United States, though the laboratories of the same works employ the centigrade notation. The growing use of the electric furnace in Germany and France calls for much American citation all in centigrade high temperatures, and while the arithmetical calculation is simple, it becomes burdensome when often repeated. I have been surprised at the numerous reprints of Table I. from centigrade to Fahrenheit degrees, first privately printed for personal use, which have been made by works, blue-prints, test-books, and technical journals, and I hope that Table II., from Fahrenheit to centigrade degrees, will be equally useful.

Jan 4, 1913

By H. O. Pickard

The Hoover and Mason Phosphate Co. made extensive tests with a rig manufactured by the Paris Manufacturing CO. as shown in Fig I. It is powered by a 20-hp Wisconsin air-cooled gasoline engine, through a single reduction gear and flexible coupling. The machine operates a 4-in. auger with a detachable cutting head, as shown in Fig I. The auger length is 3 ft 4 in. and the cutting head averages 7 in. The unit has a drilling capacity of 100 ft and can drill an average prospect hole in less than 15 min. The weight of the motor is used for the thrust feed for driving the auger and head down, aided by the spiral shape of the auger. The rate of downward motion—i.e., the feed—is regulated by a handwheel. The string of tools is withdrawn from the hole by a gear train controlled by a hand-operated clutch. In fairly dry strata, not of the consistency of mud, the action of the auger

Jan 1, 1948

By R. E. Sheppard, A. O. Martel

Zinc sinter plant fume is roasted to selectively sulfate the cadmium. Water leaching of the roasted fume recovers about 80% of the contained cadmium and produces solutions containing about 40 grams per liter cadmium and 10 grams per liter zinc. The solution is treated with sodium bichromate for lead removal. Cadmium sponge, precipitated with zinc dust, is briquetted, melted, and cast into commercial shapes. The residue from the water leach is acid leached with waste acid, solubilizing the zinc and residual cadmium. Impure cadmium sponge, precipitated with zinc dust, is separated from solution with cyclones and dewatered in a centrifuge. Air-oxidation- acid leaching of the impure sponge resolubilizes the cadmium. The resulting solution is neutralized, clarified, and treated for cadmium recovery with the water leach solution. The residue from the leached fume is water-washed and recovered in a centrifuge-thickener circuit. This residue contains lead sulfate and significant quantities of gold and silver. Manpower requirements are held to a minimum by automating operations within the Leach Plant.

Jan 1, 1973