Search Documents

By L. J. Gurevich

IN the course of the examination, at the Bureau of Standards, of fusible tin boiler plugs for the Steamboat Inspection Service, it became evident that an investigation should be undertaken to determine the precautions necessary in the manufacture of acceptable plugs. The results of the tests of these plugs show that their manufacture has improved, though at present not all of the plugs tested are satisfactory. Table 1 gives the result of tests of some 1500 plugs from about 100 makers. Records of the tests show that several of the makers were able to produce satisfactory plugs with every pouring. The Steamboat Inspection Service has the following specifications for fusible plugs: "Fusible plugs for use in boilers of steam vessels under the Jurisdiction of the Steamboat Inspection Service shall be made of bronze casing with the bore tapering continuously and openly from end to end, and filled from end to end with tin not less than 99.7 per cent. pure and to contain not more than 0.1 per cent. of lead and not more than 0.1 per cent. of zinc. The small end of the bore may be countersunk not more than 1/32 in. in depth and width, but no recess, thread, or cavity other than this countersink shall be allowed."

Jan 8, 1919

By Kenneth S. Ritchie

The natural emulsion samples used in this study were shipped directly from twelve California oil fields, through the courtesy of the superintendents of the main producing companies in those fields. Representative parts of each sample were chosen for the slides. Preparation of the slides was generally made in less than two minutes, including time of exposure; in a few cases, about five minutes was required. The short time was intended to minirmize the changes in conditions. Whenever comparison was of value, standard conditions were established. Spreading by gravity was adopted instead of smearing. Cover glasses were not allowed to rest on the films. General Characteristics of Emulsions The main purpose of the general views (Figs. 1-16) is to illustrate the general characteristics of the dispersed droplets together with any other constituent or impurity that may be found in each emulsion. The magnification is given so that dimensions could be measured from the plates. The slides used for these views had spherical recesses; they gave the best light. Where crystals were intended to be shown in the picture a filter (green was the best') was usually used. Emulsions that showed a tendency to move by concentrated light were pictured without a condenser.

Jan 1, 1931

By Walter Miller

ALTHOUGH confident of its ability to meet any demands which may be made, the petroleum refining industry is not complacent about the situation and realizes that the quantities of petroleum products to be furnished are so enormous and so far beyond what was previously estimated that the full co-operative effort of the industry must be exerted. Establishment by the President in May of the Office of Petroleum Coordinator for Defense with Secretary of the Interior Ickes at its head, plus the formation of the Petroleum Industry Council for Defense, in November, provide the channels for united endeavor within the industry and the means for gearing that endeavor within the industry and the means for gearing that endeavor in full harmony with the nation?s needs. Great strides have been made and a rapid understanding of the situation and the magnitude of the task is being attained by all concerned.

Jan 1, 1942

By Zárate G. E.

Practical and statistical considerations concerned with the sampling, sample preparation and chemical analysis of precious metal ores are reviewed. The principal requirements related with the characteristics of sample cutter, sample preparation, equipment and methods are discussed. The main errors introduced in the different stages of the sampling systems are defined. The application of statistical techniques to evaluate these errors to determine the ore grade variation and to design the number of increments needed to get an accurate assay are presented. Finally, results obtained with the application of this method to gold and silver ores are analyzed and some recommendations are given.

Jan 1, 1984

By JOHN JANNEY

STABILIZATION of the adjustment of normal consumption to normal production of world commodities is quite different from reducing production until visible surpluses are consumed. The first means restoration and maintenance of prosperity, the second means merely a temporary alleviation of a condition with the prime cause remaining uncorrected. Overproduction of foodstuffs in some sections of the world while millions starve in other sections represents not so much overproduction of foodstuffs as mal-distribution of foodstuffs. The flour mills of Washington and Oregon normally ship quantities of flour to China. Now, the wheat that would make this flour goes East instead of West. Is this overproduction, or is there something wrong that calls for study, analysis and correction? Can the plan used by the ostrich of hiding its head in. the sand get us by this present world tragedy, or must the challenge to solve this problem be met, constructively? Can we not make out of this breakdown in the world's economic system an opportunity? And use it as the stimulus for remedying the basic cause of the trouble and not content ourselves with devising temporary expedients that aim at remedying this or that of the obvious conditions, in themselves not causes at all but rather the evidence of causes, or that are the symptoms of the real trouble.

Jan 1, 1931

By G. H. Turner, R. C. Bell, E. Peters

Zinc oxide activities in a typical lead blast furnace slag have been calculated from plant operating data. These activities were used to assess the probable effect of fuel composition, oxygen enrichment, and air preheating on the efficiency and capacity of the slag-fuming operation. THE physical chemistry of zinc fuming has been examined with three objectives in mind: 1—to predict conditions favorable to increasing furnace capacity, 2—to predict the changes required to fume zinc more economically, and 3—to explain reported differences in the efficiencies of various slag-fuming plants. This study, made at ail in the plants and laboratories of The Consolidated Mining and Smelting Co. of Canada Ltd., developed from a program undertaken some three years ago on behalf of the AIME Extractive Metallurgy Div. subcommittee on slag fuming. Lead metallurgists first became interested in the recovery of zinc from lead blast furnace slags in 1905 and 1906. An excellent review of the early experimental work has been made by Courtney,' who described blast furnace, reverberatory furnace, and converter methods of fuming zinc from slag. Some of the investigators did not appreciate the importance of reducing the zinc oxide content of the slag to metal in order to fume it, since they tried compressed air blast without fuel in their earliest attempts. However, by 1908, the importance of reducing the zinc was established.' In 1925, the Waelz process for the recovery of zinc oxide from oxidized zinc ores was developed in Germany.' This process was not readily adaptable to lead blast furnace slags because of the difficulty in handling fusible charges in a kiln. What appears to have been the first slag-fuming operation as it is known was commenced by the Anaconda Copper Mining Co. at East Helena, Mont. in 1927." The first Trail furnace was completed in 1930, and this was followed by the construction of several other slag-fuming plants. During the period in which slag fuming has been extensively employed, little development of the chemistry of this process as a whole has taken place. Several good papers on the petrography of lead blast furnace slags have been published,""= but these studies could do little more than establish the forms in which lead and zinc occur in the initial charge and final products of the slag-fuming operation. In recent years, zinc-smelting problems have been ap- proached from a thermodynamic point of view. Maier has published an excellent thermodynamic treatment of zinc smelting." The important thermodynamic properties of zinc and its compounds have been determined and checked by other investigators.' However, to the best of the authors' knowledge, no thermodynamic treatment of the fuming of zinc from slag has been published. A thermodynamic study of any process requires that the essential chemistry of that process be known. In slag fuming there appear to be some differences of opinion as to whether the active reducing agent is elemental carbon or carbon monoxide. Furthermore, some observers have noted that high volatile coals appear to be more efficient than low volatile coals, indicating that hydrogen is also an important factor in the reducing efficiency of a fuel. That both hydrogen and carbon monoxide are effective reducing agents for the zinc oxide content of lead blast furnace slags can be demonstrated readily by introducing these gases into a slag bath held in a neutral vessel at 2100°F (1150°C). Elemental carbon also will reduce zinc oxide, but it is improbable that much free carbon is available for reduction of zinc, as the reaction between the finely powdered coal and air should be largely completed before the solid coal particles reach the slag. Some large-scale fuming experiments using gaseous hydrocarbons have been carried out by other investigators, but, as far as is known, these have not been developed yet into operating processes. The thermodynamic treatment in this paper is based on the following reactions: 1—to supply the thermal requirements C+V2O2- CO [1] C + 0,-CO, [2] H2+ ~z0,-H,O 131 and 2—to reduce ZnO ZnO + CO + Zn + CO, c41 ZnO + H, e Zn + H,O. [51 The furnace-gas composition also is controlled by the equilibrium constant of the familiar water-gas reaction H,O + CO + CO, + H2. C6l In order for the thermodynamic calculations to be quantitatively applicable, it is necessary that the chemical reactions to which they are being applied

Jan 1, 1956

By R. B. G. Yeo

Pronounced isothermal martensite formation at room temperature was measured dilatometrically in a steel containing 0.01 pct C, 24.9 pct Ni, 0.26 pctAl, 2.58 pct Ti and 0.25 pct Cb. It is shown that martensite will form isothermally if stabilization of the austenite-martensite transformation is eliminated by removal of carbon. The decarburization of two iron-nickel alloys allows isothermal transformation to martensite to occur at temperatures above their athermal Ms temperatures. In an Fe-22.4 pct Ni alloy, at the 0.008 pct C level, the Ms temperature during air cooling is 85°F higher than that during- water quenching-. At the 0.15 pct C level this difference is reduced to only 5°F. The introduction of carbon causes stabilization during air cooling which lowers the Ms temperature virtually to the same level as determined during mate?. quenching. Thus in the 0.15 pct C alloy, the Ms temperature is almost independent of cooling rate. It is suggested that rival theories of martensite formation should be reexamined in alloys of sufficiently low carbon and nitrogen content to eliminate the complication of stabilization. The Ms temperature of a steel containing 0.01 pct C, 24.9 pct Ni, 0.26 pct Al, 1.58 pct Ti and 0.15 pct Cb, solution treated at 1500°F and air cooled as 1/8-in. diam specimens, was found to be 57 °F. 1 However, when held for several hours at room temperature the steel hardened slightly and became appreciably ferromagnetic. Isothermal transformation to martensite was first revealed by Kurdjumov and Maksimova2 in an iron-base alloy containing 0.6 pct C, 6.0 pct Mn and 2 pct Cu. Most of the other studies of isothermal martensite have also been confined to highly alloyed steels which transform at subzero temperatures; for instance, DasGupta and Lement, 3 Cech and Hollomon, 4 Machlin and Cohen,5 Shih, Averbach, and Cohen.6 Averbach and cohen7 noted a rapidly decaying volume increase at room temperature in a steel containing 1 pct C, 1.5 pct Cr and 0.2 pct V. cina8 and Marshall, Perry, and Harpster9 have described the isothermal transformation to martensite at room and subzero temperature in stainless steels. Kurdjumov10 has recently reviewed the subject, noting that the isothermal formation of martensite can be observed only in the temperature range somewhat below Ms or below -50°C. The isothermal formation of martensite may be characterized as follows: 1) It occurs in steels of widely different compositions, the main prerequisite being a low transformation temperature. 2) The transformation occurs by the formation of new plates and not by the growth of old ones. 3) The isothermal transformation is suppresed by stabilization during slow cooling or holding at temperatures near room temperature. However, the factors governing this mode of transformation are still not fully understood. The formation of martensite isothermally suggests an activated process. The early theories of martensite formation did, in fact, utilize classical nucleation concepts. Kurdjumov 11 first proposed the presence of thermally activated nuclei of different sizes and compositions which would grow if they reached critical size during cooling. This treatment was enlarged and developed quantitatively by Fisher, Holloman, and Turnbull12,13 and was later reviewed by the latter two authors.14 Fisher15 associates Ms with a nucleation rate of one per cc per sec. At slightly higher temperatures the nucleation rate is so low that isothermal formation of martensite is not observed in reasonable times. At slightly lower temperatures the nucleation rate is so high that it could not be suppressed by rapid cooling. By judicious use of parameters Fisher 16 was able to obtain good agreement between classical nucleation theory and the incubation times of martensite formation.4 However the application of these principles to martensite formation in iron-nickel alloys15 predicts that an alloy containing about 30 pct (31 at. pet) Ni would not transform. The presence of an Ms temperature at -223° C in an alloy containing 34.1 pct (33 at. pct) Ni led Kaufman and cohen17 to reject the hypothesis of homogeneous nucleation in favor of the reaction path theory originally proposed by Cohen, Machlin and Paranjpe.18 This theory conveniently explains the formation of martensite athermally but becomes labored when dealing with isothermal formation. Kaufman and cohen19 did explain the isothermal activation of embryos by assuming it to be a result of the expansion of their boundary dislocation loops but this treatment predicts an upper temperature limit of isothermal martensite formation.

Jan 1, 1962

By R. H. Walpole, J. M. Kane

IN all probability the mining and metallurgical industry as a whole can demonstrate a larger ecorlomic return from installation of dust-control equipment than any other major industrial group. This fact has partially accounted for the marked increase of dust-control installations made during the past decade. While the primary objectives for installation of dust-collecting systems are improved working and operating conditions for men and equipment, the fact that an economic return can be anticipated on salvageable materials is an added advantage which shows in partial or complete equipment write-off. The conditions apply to most phases of the mining, milling, and smelting industry, both non-metallic and metallic. As with any mechanical devices, selection of suitable dust collector equipment involves evaluation of available products with characteristics most nearly meeting conditions of the application at hand. When there is valuable product to be collected, and/or when there are possibilities of air pollution or public nuisance, collector selection is often guided by the maxim of "highest available collection efficiency at reasonable cost and reasonable maintenance." A brief review of dust collector designs will permit outlining of major characteristics of each group. Final selection will involve detailed data against a background of the problem under consideration. The dry centrifugal collectors, see Fig. 1, represent a group of low cost units with minimum maintenance. They are subject to abrasion under heavy abrasive dust loads and to plugging with moist materials. Efficiency drops off rapidly on particle sizes below the 10 to 20 micron group. Because of the large amounts of —10 micron particles in most mining dust problems, they will normally be used as primary collectors and will be followed by high efficiency units. This combination is cspecially popular where the bulk of material is desired in a dry state with wet collection indicated for the final cleanup portion. In remote plant locations, dry centrifugal~ can be used alone if product in dust form has no value or if dust loading is light enough to eliminate a nuisance in the plant area. Where high efficiency dust colleotion equipment must be selected, choice will normally involve fabric arresters, wet collectors, or high voltage Electro-Static precip-itators. Fabric arresters, see Fig. 2, rely on the passing of dust-laden air at low velocity through filter fabric. Velocity ranges from 1 to 3 fpm for the usual installation and may be as high as 10 to 20 fpm in arrangements where automatic frequent vibration or continuous cleaning of the filter media is employed. Fabric is normally suspended in either stocking type or in an enlvelope shape. Collection efficiency is excellent even on sub-micron particle sizes. Equipment is bulky, must be vibrated to remove the collected dust load, and is restricted in applications from temperature and moisture standpoints. Condensation of moisture on the fabric filter mcdia causes plugging of the passages with great reduction in air flow. Temperatures for the usual medias of cotton or wool are 180" and 200°F maximum, although the introduction of synthetic materials such as nylon, orlon, and glass cloth have increased the possibilities of this type of collector for higher temperature applications. The wet-type collector may employ a number of different principles so that entering dust particles in the gas stream are wetted and removed. Principles usually include impingement on collector surface or water droplets, often in combination with centrifugal forces. Variety of wet collector designs is indicated by typical collectors illustrated in Figs. 3 and 4. Collection efficiency is a function of the particular design, although the better collectors will have high collection efficiency on particles in the 1-micron range. Wet collectors have the advantage of handling hot or moist gases, take up small space, and eliminate secondary dust problems during the disposal of the material. At times collection of the material wet is a disadvantage. Wet collectors may also be subject to corrosion and freezing factors. The high voltage Electro-Static precipitator, see Fig. 5, is probably the most expensive type of high efficiency collector. It finds its applications generally in problems in which collectors previously discussed cannot be employed. Its collection efficiency is based on its design features and can be excellent on the finest of fume particles. Material is normally collected dry. Gas temperatures are of no great concern as long as condensation does not occur within the dry type of precipitator and the temperatures do not exceed the limits for materials used in its construction. As with the fabric arrester, provisions

Jan 1, 1954

By K. G. Kreider, J. H. Brophy, J. Wulff

The technology of nickel-activated sintering of tungsten powder has been successfully applied to the densification of plasma-sprayed tungsten. Nickel was added by infiltration in a zinc solution followed by evaporation of the solvent. After sintering one hour at 1300°C density 95 pct of theoretical and transverse rupture strength of 74,000 psi were obtained. Shrinkage was found to be anisotropic and the mechanism of densification was comparable to that found in the nickel-activated sintering of tungsten powder. 1 HE use of a plasma spray gun for the fabrication of massive tungsten parts has become increasingly interesting. Applications now exist where a deposit in the as-sprayed condition is satisfactory. However, these deposits are generally characterized by a lamellar anisotropic microstructure containing 15 pct porosity of which, typically, two-thirds is open to the surface. Mechanically, the as-sprayed deposits fail at relatively low stress levels with a biscuit-like fracture. As a result of these problems the possibility of improving structure and strength by sintering treatments subsequent to spraying is particularly attractive. Preferably this sintering treatment should be adaptable to large bodies of sprayed metal. The similarity between the as-sprayed tungsten structure and that of a powder compact suggests that the relatively low-temperature activated sintering technique1 might be profitably employed in the densification of plasma-sprayed tungsten. It was the purpose of the present investigation to develop a technique for introducing the nickel-activating agent into the sprayed structure, to evaluate the amount and mechanism of densification obtained as a function of time and temperature, and to obtain an indication of the relative strength before and after sintering. EXPERIMENTAL PROCEDURE Powder used for spraying was purchased from the Wah Chang Corp. in several size fractions ranging from an average size of 4 to 150 . These powders were sized further for an explicit study of the influence of average feed size on densification. All powders were dried at 200°C before use. Spraying was accomplished with a Plasma Flame unit manufactured by Thermal Dynamics Corp. Several modifications of the unit were helpful in conducting the investigation. A variable speed auger feed mechanism coupled with the carrier gas mecha nism facilitated the use of fine particle sizes. A coil of ten turns of copper tubing in series with the arc power and concentrically would around the nozzle improved nozzle life and extended the range of operating currents available. The function of the auxiliary coil was to cause the arc to spin and to prevent impingement at only one point in the nozzle. Normally air sprayed deposits were made with an arc maintained at 400 amp at 50 to 70 v. The arc was blown by a gas mixture containing from 5 pct H, 95 pct N for the finest powder feed sizes ranging to 20 pct H, 80 pct N for the coarsest size. The flow rate was maintained at 100 cu ft per hr NTP through a nozzle of 0.25 in. ID. When apraying in air, the powder stream was directed toward an aluminum substrate for ease of mechanical removal of the deposit. The substrate was cooled by diverting the plasma flame with an air jet, and a second jet was directed on the deposit surface. In this configuration a gun-to-work distance of 2 to 3 in. was found to be satisfactory. Fig. 1 represents a typical as-sprayed deposit micro-structure. Laboratory studies of protective atmosphere spraying were carried out in cylindrical chamber 8 in. in diam by 18 in. in length. In operating the nozzle attached to such a chamber, particular care was required to avoid nozzle burn out due to reduced gas flow. The structure and density of the chamber sprayed deposits varied over wide ranges depending on substrate temperature. For the purposes of this investigation, flat deposits were made approximately 2 in. sq by 3/8 in. thick. From these deposits individual samples were cut an ground to a rectangular shape typically 1 1/2 in. by 1/8 in. sq such that the long dimension was perpendicular to the spraying direction. For the study of shrinkage anisotropy deposits up to one inch thick were produced. From these, rectangular samples were cut having a longer dimension parallel to the spraying axis. Prior to the addition of activating agent, the samples were deoxidized in hydrogen at 800°C for 20 min. No detectable dimensional or microstructural change was observed after this treatment. The addition of nickel was accomplished by infil-

Jan 1, 1963

By M. Shelef, A. W. Fletcher

The effect of alkali sulfates in promoting the sul-fation of nickel and copper in a bulk sulfide flota -tion concentrate by fluidized bed roasting has been studied in the laboratory, and it was shown that the various alkali sulfates promote sulfation to approximately the same extent. The sulfation of a mixture of synthetically prepared iron and nickel oxide and of nickel ferrite has also been studied. Nickel sulfation was promoted by high ratios of Fe:Ni and by the presence of sodium sulfate. THE work described in this paper was a continuation of earlier studies into the role of alkali sulfates in promoting the sulfation roasting of nickel sulfides1,2 in an endeavor to determine how the system was affected by the presence of compounds of iron and copper. The earlier work1 showed that, in the sulfation of NiO at 680°C, the reaction was limited by the formation of an impermeable film of nickel sulfate on the oxide surface. The relative effect of the various alkali sulfates in promoting nickel sulfation varied in the order: Li > Na >Cs > Rb > K A study of alkali sulfate/ nickel sulfate interactions at high temperatures showed that the promoting action was due to the fact that the nickel sulfate product layer sintered and agglomerated only when the more active additives were present. This resulted in the formation of discontinuities in the nickel sulfate layer so that diffusion of the sulfating gases to the NiO surface was no longer impeded and the reaction could proceed to completion. A similar explanation was used for the observation that sodium and lithium sulfates promote the oxidation of NiS to NiO at temperatures below 750°C since small amounts of nickel sulfate were formed during oxidation.2 It was of interest to study the effect of alkali sulfates on the sulfate roasting of a sulfide flotation concentrate which is typical of material treated commercially. In order to control temperature it is essential to roast sulfides in a fluidized bed and this technique was therefore used, although the batchwise operation of a small-scale laboratory reactor does not reproduce all conditions which prevail in full-scale continuous plant. The results obtained are therefore only comparative, and cannot be used for predicting the optimum conditions for metal extraction. The sulfation of synthetically prepared mixed oxides of nickel + copper and nickel + iron and of nickel ferrite was also studied to evaluate the relative effects of alkali sulfates with more complex systems. SULFATION ROASTING OF A SULFIDE FLOTATION CONCENTRATE The bulk sulfide flotation concentrate used in this work contained 7.92 pct Ni, 1.74 pct Cu, 35.66 pct Fe, and 31.28 pct S. The sulfide minerals present in order of abundance were pyrrhotite FeS, pyrite FeS2, pentlandite (FeNi)S, and chalcopyrite CuFeS2. Two samples described as coarse and fine were used. The coarse sample, which was a flotation concentrate (58 pct plus 300 mesh), was ground to 100 pct minus 350 mesh to produce the fine sample. Before roasting, the sample of sulfide concentrate was agglomerated by wetting witli a solution of the alkali sulfate (or water), thoroughly mixing, and drying at 110°C. This gave a cake which was gently crushed and screened, the -18 +100 mesh fraction being used for fluidized bed roasting. A similar-size fraction had been used by the authors in pilot plant work with a 4-in.-diam fluidized bed reactor.' In this work it was found that the molar ratio of additive to the total iron + nickel + copper content of the sulfide sample should be adjusted to a value of approximately 0.06, as this was the optimum amount necessary for nickel sulfation. Experimental. The fluidized bed reactor consisted of a quartz tube approximately 60 cm long and 30 mm in diameter resting in a vertical tube furnace. The sulfide bed (30 g) was supported on a bed of -4 +12 mesh quartz particles 3 cm high, which rested on a sintered quartz disc welded to the tube. The temperature of the furnace was controlled with a variable transformer to give a final bed temperature of 680°C. The bed was fluidized with air or mixtures of air + 10 pct v/v SO2, at a total apparent gas velocity of 60 to 65 cm per sec at 680°C. The SO2 was introduced into the fluidizing air stream only when the oxidation of the sulfides was completed. At the end of the roasting period the calcine was leached with boiling water and the

Jan 1, 1964

By Rudolph G. Wuerker

The progress made in testing the strength of rocks and minerals as they are encountered in mine operation is reviewed. An attempt is made to correlate these physical measurements with abrasive hardness, grindability, and behavior in comminution on one hand and fracture of rocks in pillars and roof control on the other. THIS paper reviews the progress made in testing the strength of rocks, ores, coal, salts, and other minerals as they are encountered in mine operations. It attempts to correlate the results of these physical measurements with technological properties more useful to the mining engineer: abrasive hardness, grindability, and behavior in comminution on one hand, and roof control, fracture of rocks in pillars, and mining methods with controlled caving on the other. In the following pages, the materials discussed will be referred to as rocks. Basic to rock mechanics and comminution are the problems of strength, elastic behavior, and failure, common to all brittle materials. A distinction will be drawn as to theoretical and applied research, and discussion of the progress made in each field will include test data obtained by the U.S. Bureau of Standards,1-1 the U.S. Bureau of Mines," the Iowa Engineering Experiment Station,"." the Committee on Geophysical Research at Harvard University,'" Basic Industries Research of the Allis-Chalmers Manufacturing Co.,11,12 by Philipps,13 and by Mueller," to name only a few. With refinements of testing methods and increased standardization. more useful and more comparable results have been achieved. This is especially important in testing a material like rock, as the inherent heterogeneity demands careful and exacting procedures. New measuring procedures that appear to supersede well known standard methods have contributed to faster and less costly testing yet have introduced new concepts, with implications as to comparability of results which must be watched. Reference is made to the sonic method for determining elastic properties," to be discussed in detail below. Basic Investigations Historically, all work in the field has started with the simplest determinations such as those for crushing strength, abrasive hardness, and grindability. These serve the limited objectives in the researcher's field of specialization: building construction, road ballast, roof control in mines, comminution, and seismic prospecting. Occasionally, fundamental properties like the modulus of elasticity E and Poisson's ratio v have been determined with the idea that they might have some bearing on the technological properties of the material under investigation. But it was not until the work of Philipps,13 of Harvard University,'" and of the U.S. Bureau of Mines"' that sufficient basic data were collected to allow researchers to go beyond the technological test and find the fundamental laws behind the behavior of rocks in mine and mill operations. The properties to be looked for are those that describe the elastic behavior of any material, the modulus of elasticity E and Poisson's ratio v being the ones determinable with least difficulties. Only two such properties are required to compute any other property such as the shear modulus, the modulus of rigidity, and the bulk modulus, all of which are related to each other according to well known equations of the theory of elasticity." In spite of their heterogeneous character, all rocks tested have possessed elastic properties. This does not mean that rocks of the same type always have the same modulus of elasticity, which varies exactly as the crushing strength or any other physical property of a rock can spread over a wide range. This has been explained by imperfections of the material always found in rocks, but to some extent this scattering of data is caused by inaccuracies inherent in the testing methods. Modulus of Resilience, a Criterion of Failure Increased availability of E values should allow us to test the validity of the quantity of strain energy theory which has been used in the solution of roof control problems by Philipps13 and by Holland.'" Recently Bond and Wang12 have applied this theory to explain the failure of an elastic material in comminution. Actually it is a very old theory, proposed as far back as 1885 by Beltrami.16 By its assumption the condition of yielding is determined by the term S2 M, = — x volume. Here M, is the modulus of 2E resilience, and its dimension is inch-pounds per cubic inch, that is, work per unit volume. Its numerical value is equal to the area under the stress-strain diagram. In the foregoing equation S is the yield stress (in psi) in tension or compression, whatever the case may be. E, the modulus of elasticity, is in psi. The great appeal of Beltrami's concept of stored energy lies in the fact that the two properties which seem to influence failure most, strength and elasticity, occur in the formula for the modulus of resilience. As an illustration of this, the moduli of resilience in compression of some typical materials tested by the U.S. Bureau of Mines" have been plotted in Fig. 1. The sample of concrete of conventional mix is shown only for the sake of comparison. Its determination was made in the Department of Mining and Metallurgical Engineering, University of Illinois. The values of the moduli of resilience of the various specimens in the plot are:

Jan 1, 1954

"Coulter's Rainbow and Crooked Falls are situated about five miles below the City of Great Falls. Coulter's, the first of the series in the course of the river, is unimportant and has been submerged by the Rainbow dam. Next below Coulter's is the Rainbow Falls, 47 feet in height. Following Rainbow Falls is the Crooked Falls, 21 feet in height. The power developed at this point is such that the one clam, power house and tail-race utilize the power from all three of the above falls.The development at Rainbow was started October, 1908, and completed July, 1910. It has a total capacity of 21,000 k-w. in generators, and 36,000 h-p. in waterwheels, and operates at 105 foot head. The general scheme of development is typical of what may be called standard practice in the west for plants of medium head, and consists of a low diverting clam, a double pipe line feeding into a balancing reservoir near the plant, and individual pen-stocks supplying the turbines from this reservoir.The dam is a rock-filled crib structure 1,146 feet long and 29 feet high, the up-stream side of which slopes at such an angle that the stability of the clam is assured even under the greatest floods, the weight of the water acting to hold it down, so that the higher the flood the greater the stability. The down-stream side is also sloping and tapers off into a long apron so designed as to take care of any overflow which may occur without shock or commotion. The clam is founded on solid rock throughout its entire length."

Jan 1, 1913

By R. K. Datta

Eluropium -activated yttrium vanadate, excited by short- and long-wavelength ultraviolet radiations, shows enzission lines near 6100A, the principal ones correspondirzg to transitions of EU+3 ions from 5Do to the F2 energy level. The ~neclmlallistns of absorption and etnissiorz of this phosphor have been empirically studied. The absorption is caused by two separate processes in the matrix. The phosphor YVO4:Eu and tlie matrix YVO, haue essentially the same resectance spectra in the region 2500 to 4000if. There are two broat ah~o?~ption bands: natnely, around 2600 and 3600A regions. Whet? compared with the reflectance spectra of the constituent oxides, namely, Y2O3, V205, Eu2 03, the absorption bands of the tnatvix and the phosphor in the short- and long-wavelength ultraviolet regions can be interpreted as due to charge-transfer processes involving i) Y-O and ii) 17-0, respecti~~ely. The excitation spectrum' of the phosphor has two broad bands with peaks at about 2600 and 3600A regions. U can be postulated that enevgy absorbed under short- crud long-wavelength ultraziolet excitatzon, respectzcely, by Y-0 and V-O parts of the niatrix is transferred by radcatio~zless process to EU+3 ions. Thzs postulate can empirically be proved on the basis of the spectra of the systems (YVO4,-YPO4,):Eu. PO? ~ons do not have' any appreciable absorption in the short or long uv regions. When P0't3 ions are substitlited for v0i3 ions in YVO,:Eu phosphors, the absorption and excitation in the lo~zg uv region are gradually reduced. Ailoreover, the £«+3 emission under 3650A excitation is decreased zuitlz increase in PO^ content, lt~lzereas the emission under 253711 excitation remains esserztially constant with as IILUCIL as 60 mole pct of YPO, in YVO,:En. EUROPIUM-activated yttrium vanadate (YV04:Eu) is a well-known phosptor.'-3 When excited by cathode rays, 2537, or 3650A radiations, YV04:Eu emits typical narrow-band spectrum of EU'3 fluorescence in the region of 5900 to 7100A, a very strong maximum occurring at about 6190A. This emission is considered to be due to 5Do — 7F2 transition of excite: EU*3 in 4f state. Moreover, the emission under 3650A excitation increases with temperature markedly. Because of these properties, YV04:Eu phosphor finds wide application in industries, namely, in color television tube, laser, and high-pressure mercury-vapor lamps. It is the purpose of this paper 1) to present the empirical study of the mechanism of absorption and excitation of YV04:Eu phosphor by ultraviolet radiation, and 2) to offer an explanation for the process of emission. It should be mentioned that a theoretical discussion on the mechanism of absorption in terms of the crystal or ligand field theory is beyond the scope of this paper. Empirical studies presented here are based primarily on spectroscopic and crystal-chemical investigations. EXPERIMENTAL i) Preparation of Materials. The synthesis of vanadate phosphorinvolves preparation of (Yi-.tEuj^Oj, blending the mixed oxide with an oxidic compound of vanadium, such as V205 or NH4V03, and firing the mixture at about 1000°C for several hours when YVO4:Eu forms as a primary phase. (Y1-xEux)203 compositions are prepared by coprecipitation of oxalates, and igniting them at about 1000°C. The vanadium compound is added in excess of the stoichiometric proportion for fluxing purposes. The charge is cooled, ground, and the excess of vanadium is removed by a hot wash (-80°C) of alkali or ammonia. Y(VP)04:Eu samples are prepared by mixing (Yi-xEux)203 with stoichio-metric proportions of (NH4)2HP04 and the vanadium compound. The mixtures are prefired at 700" to 800°C for 1 or 2 hr, then ground and refired at 1150°C. The firings of the phosphors are done in silica crucibles, and the homogeneity of the final products checked by X-ray diffraction analysis. ii) Spectroscopic Measurements. Diffuse reflectance sqectra of the samples within the range 2500 to 7000A are obtained by using CaF2 as standard in Cary Recording Spectrophotometer, Model No. 14. The emission spectra from phosphor plaques, excited under different ultraviolet sources, are obtained by a direct-recording spectroradiometer4 adapted with a grating monochromator with nearly constant dispersion. Maximym sensitivity in the spectral region from 2500 to 7000A is obtained with a quartz-windowed, S-20 response p$otomultiplier. The total' band pass is kept about 30A. The spectra are calibrated against the light from a standard tungsten filament lamp reflected from a magnesium-oxide plaque. Brightness data given throughout this report $re measured from the height of the main peak (6190A) of the emission spectra. The excitation spectra are measured using sodium salicy-late as standard. RESULTS AND DISCUSSION The diffuse reflectance spectra of both pure and activated YV04, along with their constituent components, are shown in Fig. 1. YVO4 shows two broad absorption bands, namely, around 2500 and 3600A, respectively. Since there is little difference between the reflectance spectraoof YVO4 and YVO,:Eu in the uv region (2500 to 4000A), it can be postulated that excitation of the phosphor is mainly due to absorption by the matrix, i.e., YVO4. The question, now, is whether the matrix (Yv04) is excited as a whole, or different components are responsible for the two absorption bands. The characteristic absorption spectra of molecular ions involving transition metal ions, both in aqueous solutions and in crystals, are due to electronic transi-

Jan 1, 1968

By J. U. Messenger

A technique is described whereby the resistance of an emudian to breaking can be quantitatively determined. Produced ailfield emulsions are usually the water-in-oil type and, accordingly, do not conduct an electrical current. However, there is a threshold of A-C voltage pressure above which an emulsion will break and current will flow. The more stable an emulsion, the higher the required voltage. A Fann Emulsion Tester, modified so that low voltages (0 to 10 v) can be accurately measured, is suitable. This technique has application in evaluating the effect of a demuksifier on the stability of an emulsion. Emulsions can, in essence, be titrated with demulsifiers by adding a quuntity of demulsifier, stirring, and measuring the voltage required to cause current to flow. Any synergistic effect of two or more materials added simultaneously can be followed accurately. A demulsifier that significantly lowers the threshold voltage (from 100 to 400 v to 0 to 10 v for the emulsions in this study) is effective and can cause the enlulsion to break. A demulsifier that will bring about this drop in the threshold voltage at low concentration ir very desirable. The technique is also well adapted for rapidly screening demulsifiers. INTRODUCTION Stable emulsions in produced reservoir fluids resulting from certain well stimulation and completion procedures are common problems. The use of suitable demulsifiers can often mitigate these difficulties. At the present time, a rapid and efficient method for selecting satisfactory demulsifiers is not available. It is badly needed. Reliance is now placed primarily on trial-and-error procedures. A new test method has been developed which permits a more rapid and precise selection of demulsifiers. It involves measuring the electrical stability potential of an emulsion before and after a demulsifier has been added. This paper describes this method and shows where it should have application in field emulsion problems. NATURE OF OILFIELD EMULSIONS Two immiscible components must be present for an emuhion to form; we are concerned here with crude oil and water. An emulsifier must be present for tin emulsion to be stable. J Emulsifiers can be substances which are soluble in oil and /or mter and which lower interfacial tension. They can be colloidal solids such as bentonite, carbon, graphite, or asphalt which collect at the interface and are preferentially wet by one of these phases. Unrefined crude oils can contain both types of emulsifiers, A popular theory is that, of the two phases in an emulsion, the dispersed phase will be the one contributing most to the interfacial tension.' Usually this phase contains the least amount of emulsifier. The stability of a water-in-oil emulsion is affected by the fol1owing: l) viscosity; (2) particle or droplet size; (3) interfacial tension between the phases; (4) phase-volume ratios; and (5) the difference in density between the phases. A stable emulsion is usually characterized by high-viscosity, small droplets, low interfacial tensions, small differences in density between its phases, and slow separatian of the phases. It also has low conductivity (high electrical stability potential). Water-in-oil and oil-in-water emulsions"' are both common; however, oil field emulsions are predominantly water-in-oil emulsions. The emulsions which commonly occur during oompletion and stimulation operations contain a combination of several of the following: acids, fracturing fluids (oil, water, acid), and formation water and oil. Produced emulsions usually contain formation water and oil. Emulsions form in oil wells because oil and water are mixed together at a high rate of shear in the presence of a naturally occurring or unavoidably produced emulsifier. During the completion and stimulation of productive zones, and while formation fluids are being produced, oil and water are very often commingled. These mixtures are formed into emulsions by agitation which occurs when the fluids are pumped from the surface into the matrix of the formation or produced through the formation to the surface. Restrictions to flow (such as perforations, pumps, and chokes)".'" increase the level of agitation; tight emulsions are more likely to form under these conditions. Often an emulsified droplet is an emulsion itself.'" Therefore, emulsion-breaking problems can be quite complex. The complexity can be even greater if a third phase (gas) is included. Demulsifiers operate by tending to reverse the form of the emulsion. During this process, droplets of water become bigger, viscosity is lowered, color becomes darker, separation of the phases faster and electrical stability potential approaches zero. Any of these effects could be followed as a means of determining emulsion stability. However, electrical stability potential is the most reproducible and most easily measured parameter for following the stability of a water-in-oil emulsion.

Jan 1, 1966

By R. G. Agarwal, Ramey Jr. H. J., Al-Hussainy R.

Although it has long been realized that gas recovery from a water-drive gas reservoir may be poor because of high residual saturations under water drive, it appears that only limited infomlation on the subject has been available until recently. This study was performed to show the qiiantitative potential importance of water influx. Results indicate that gas recovery may be very low in some cases: perhaps as low as 45 per cent of the initial gas in place. Gas recovery under water drive appear to depend in an important was on: (I) the prodirction rate and manner of production; (2) the residual gas saturation; (3) aquifer propertie.); and (4) the volumetric displacement effciency of water invading the gas reservoir. The manner of estimating water-drive gas reservoir recovery can vary considerably. Examples are: the steady-state tnethorl. the Hurst modified steady-state method, and various unsteady-state methods such ac. those of van Ever-dingen-Hurst, Hurst, and Carter-Tracy. The Carter-Tracy water influx expression was used in this study. In certain cases, it appears that gas recovery can be increased significantly by controlling the production rate and manner of production. For this reason, the potential importance of water influx in particular gas reservoirs should he investigated early to permit adequtrtr planning lo optirtize the pay reserves. INTRODUCTION In recent years, the economic importance of natural gas production has become increasingly apparent. This has been evidenced by more intensive exploration efforts aimed at gas production, and exploitation of both deep, as well as low-permeability gas reservoirs. Technical developments such as deep-penetration fracturing have made development of such formations economically feasible. Unfortunately, water influx has forced abandonment of a number of gas reservoirs at extraordinarily high pressures. Although reservoir engineering methods for estimating water influx have long been available, it appears that application of these methods to the water-drive gas reservoir has been sporadic.'a Available methods for estimating water influx which can be applied to the water-drive gas reservoir problem include the steady-state method,1 the Hurst modified steady-state method and various unsteady-state methods such as those of van Everdingen-Hurst. Hurst, and Carter-Tracy. Interesting applications of these solu- tions to gas reservoir and the aquifer gas-storage problems have appeared recently.3,12,14 The experimental study of residual gas saturations under water drive by Geffen et al. in 1952 indicated that residual gas saturations could be extremely high. A value of 35 per cent of pore volume is often used in field practice when specific information is not available. The study of Geffen et al. showed that residual gas saturation might be much higher in some cases. Naar and Henderson concluded that the residual non-wetting phase saturation under imbibition should be about half of the initial non-wetting phase saturation. The Naar and Henderson result that residual gas saturation under water influx should be about half the original gas saturation is recommended as an estimate if laboratory measurements are not available. Thus, it is clear that a considerable portion of the initial gas in place might be trapped in a water-drive gas reservoir as residual gas at high pressure. A full water-drive would result in loss of residual gas trapped at initial reser.voir pressure. Consideration of transient aquifer behavior leads to the conclusion that high-rate production of water-drive gas reservoirs could result in improved gas recovery by reduction of the abandonment pressure. However, there appears to be little quantitative information on this possibility. One of the few advantages of water-drive gas production appears to be improved deliverability through water-drive support of the reservoir pressure. There may also be an advantage in higher condensate recovery caused by pressure maintenance for gas-condensate water-drive reservoirs. In view of the preceding, this study was made to assess the potential importance of water-drive in gas reservoir engineering. The Carter-Tracy approximate water-influx expression was used because this equation offers some advantages in hand-calculation which do not appear to have been generally recognized.' However, calculations were performed in the main with a high-speed digital computer to permit evaluation of the effect of water-drive under a large variety of conditions. CALCULATION METHOD Water-drive gas reservoir performance can be estimated in a manner completely analogous to oil reservoir calculations: a materials balance is written for the reservoir, and a water influx equation is written for the aquifer. Siniltaneous solution provides the cun~ulative water influx and the reservoir pressure. When reservoir performance data (gas produced and reservoir pressures) are available, it is usually possible to match performance data to determine the initial gas in place and the water influx parameters —

Jan 1, 1966

By Charles Will Wright

THE economy as well as the living standards of a country depends largely upon adequate supplies of raw materials at reasonable prices. Geological and climatic conditions responsible for the occurrence of commercial minerals and the growth of raw agricultural and forest products are so varied in different parts of the world that no country can be self-sufficient. The world is rapidly shrinking because of improvement in transportation facilities, but populations are steadily increasing and so are the needs for a greater production of raw materials and for their more equitable distribution. Too many barriers between nations prevent free access to the main sources of supply of the raw materials vital to neighboring nations and it is just such barriers that are often the cause of friction and even war. The International Trade Organization is doing a commendable job in helping to. break down barriers and to reduce friction, and we should now find ways to facilitate access to these sources of supply and encourage more efficient and greater production of the raw materials so urgently needed throughout the world. This cannot be done by individual selfish governmental agencies, influenced as they are by politics, nor by socialistic governments attempting to nationalize industries. It can be done efficiently only by the free individual through private enterprise properly protected against adverse governmental action. This protection can be supplied by the World Bank.

Jan 1, 1948

By S. F. Ravitz

IN his excellent book on the Principles of Flotation, Wark' makes the following significant statement concerning the theory of flotation: Two questions of first-rate importance must be considered . . . First, it must be decided whether the sulfide minerals require a collector in order that they may float, or whether as has been claimed, they possess an inherent floatability and need no collector. Second, it must be decided whether the xanthate type of collector can react with or be adsorbed by the unchanged sulfide minerals themselves, or whether, as many claim, reaction with the collector is dependent upon initial oxidation of the mineral surface. In the theory of flotation there are no two questions of greater importance than these. Ravitz and Porter' presented evidence that galena can be floated without a collector, and even without any reagent, provided oxidation products are thoroughly removed from its surface. They found also that thoroughly cleaned galena floated faster when xanthate was used than when a frother alone or no reagent was used, and that, without a collector, the recovery decreased gradually upon exposure of the mineral to air. Their work, however, has met with considerable criticism. I(127).3-6 This paper is presented to answer the objections that have been raised, and to present additional data that confirm their results. EXPERIMENTAL PROCEDURE The apparatus used to provide oxygen-free conditions for flotation has been described in detail by Ravitz and Porter. An atmosphere of purified nitrogen was maintained within the apparatus; all water and solutions used were freed of dissolved air, and could be transferred where desired by the use of nitrogen pressure; nitrogen was used as the gaseous medium for flotation. The flotation cell was essentially a glass cylinder 15 cm. long and 4.6 cm. in diameter. Near the bottom was sealed a fritted glass filter, which broke up the gas into small bubbles, and 6 cm. above this filter was a side arm through which the froth overflowed. The pulp was agitated by a glass impeller, which entered the cell through a mercury seal. For each test 17 grams of galena and 75 ml. of water were placed in the cell, after which the speed of the impeller and the rate of gas flow were adjusted. Water was added gradually during the test to keep the froth level at the proper height. The mineral was prepared and cleaned in the following manner. Exceptionally pure galena was crushed by hand on a clean bucking board, screened to - 150+ 200 mesh, and deslimed on a zoo-mesh sieve with a fine spray of water. It was then boiled on a hot plate for a number of hours with several changes of the desired cleaning solution, after which both the solution and the mineral were placed in the "mineral flask" of the apparatus. The cleaning solution was drained off, and the mineral was boiled with oxygen-free water

Jan 1, 1940

By John R. Spencer

A capillary tube variable volume cell is described, which has operated satisfactorily over a range of 100°F and 3,500 psi to 550°F and 1,500 psi. The cell contents are entirely visible over the length of the capillary with the exception of a space at the top amounting to three per cent of the total volume. Observations on the critical behavior of simple systems have been greatly facilitated by the apparatus, it being possible to establish the critical conditions for a particular mixture in the course of a day's run. INTRODUCTION Many types of apparatus have been designed for obtaining data on the phase relationships of hydrocarbon systems. Such apparatus can in general be subdivided into two classifications; (l), indirect measurement of phase volume, and (2), direct visual observation of phase volume, each of which has outstanding advantages and disadvantages. Indirect measurement of phase volume requires the use of rather elaborate apparatus including internal probes in which are located the device for determining the locus of the interface between phases. Such equipment is by its very nature costly, and is complex from the standpoint of operating technique. Probing techniques can be used, however, over wide ranges of temperature and pressure with a high degree of reproducibility. Apparatus for visual observation of phase behavior obviously has the advantage of enabling the experimenter to see exactly what takes place, but because the material to be tested is contained in a cell constructed of both metal and glass, is limited severely as to the temperature range of operation. Furthermore. the maximum pressure usually is limited by the choice of material used for sealing the glass to the metal, and by the strength of the glass itself. In the interest of increased efficiency of observation, as much of the cell as possible should be visible to the eye. Glass capillary tubes have been used successfully but have always given difficulty at the metal-to-glass seal. An apparatus has been devised to overcome the problems of sealing and resistance to temperature effects that have heretofore been the limiting factor with glass apparatus in the observation of phase volumes at elevated temperature and pressure. APPARATUS The objective which dictated the general arrangement of the apparatus (Figs. 1 and 2) was simplicity of operation. The air bath, A, was constructed of an iron framework to which was attached approximately one inch of glass wool bats which were covered on the outside with "Masonite." A roughly octagonal center piece was installed to provide forced circulation of the air by the fan, B, past the heaters, D, cell, F, and thermoregulator, C, respectively. The entire top of the box is removable to facilitate charging of the cell and to permit easy maintenance. Two windows are provided before and behind the cell to allow the operator to observe the contents against the background fluorescent light, E. The heaters,

Jan 1, 1951

By C. H. Bushell, M. Malnarich

REAGENT control in flotation is more an art than a science. Operators vary the amount of reagents used according to the metallurgy obtained. The amount of collector may be increased, for example, if tailings losses are high and decreased if concentrate grades are low. Often control decisions are based on only one assay, such as the tailings analysis by microscopic or quick assaying techniques. This method of control has given reasonably satisfactory results but is clearly far from perfect. No adjustment in reagent addition can be made until information is received that metallurgy has deteriorated, that is, until the optimum time for adjustment has already passed. The first adjustment probably will be an overcorrection or an undercor-rection, and time will be required to establish the best new addition rates. The seriousness of the problem depends on variability of the ore. In ore of continually shifting composition and complexity, mill results will shift back and forth from excessively high concentrate grades and high tailings losses to excessively low concentrate grades and low tailings losses. Economic incentive for improved control also increases with increasing size of mill. Even a small improvement in percentage recovery in a large mill pays for expensive control equipment. The Sullivan concentrator of The Consolidated Mining & Smelting Co. of Canada Ltd. at Kimberley, B. C., treats 11,000 tpd of complex lead-zinc ore, a scale of operations which justifies an extensive research program on automatic control. Work has followed two separate lines: 1) development of faster analytical methods for pulps, and 2) study of metallurgical control by measurement and control of reagent concentrations in flotation solutions. Although work is incomplete in both phases, a progress report can be given on the development of reagent control. The primary requirement in flotation is selective attachment of particles of one mineral to air bubbles while the other minerals remain detached. Hydrophobicity of mineral surfaces is established by the collector, which coats the minerals by adsorption. The requirement of selective affinity for air bubbles is therefore equivalent to requiring selective adsorption of a collector. Adsorption theory, supported by abundant experimental evidence, shows that the amount of a reagent adsorbed at a surface must be a function of its residual concentration in solution. As the concentration in solution rises, the amount adsorbed increases, usually following some type of logarithmic curve. Selective adsorption must depend on a natural difference in the minerals, but ordinarily the differences in affinity are not great enough to obtain complete coverage of one mineral while the others are completely uncoated. An optimum concentration will exist, below which coverage will not be great enough to float enough of the valuable mineral, and above which too much unwanted mineral will float. All other reagents, except some frothers, affect the amount of collector adsorbing at constant residual collector concentration in solution, either by adsorbing competitively with the collector, or by a

Jan 1, 1957

By John R. Spencer

A capillary tube variable volume cell is described, which has operated satisfactorily over a range of 100°F and 3,500 psi to 550°F and 1,500 psi. The cell contents are entirely visible over the length of the capillary with the exception of a space at the top amounting to three per cent of the total volume. Observations on the critical behavior of simple systems have been greatly facilitated by the apparatus, it being possible to establish the critical conditions for a particular mixture in the course of a day's run. INTRODUCTION Many types of apparatus have been designed for obtaining data on the phase relationships of hydrocarbon systems. Such apparatus can in general be subdivided into two classifications; (l), indirect measurement of phase volume, and (2), direct visual observation of phase volume, each of which has outstanding advantages and disadvantages. Indirect measurement of phase volume requires the use of rather elaborate apparatus including internal probes in which are located the device for determining the locus of the interface between phases. Such equipment is by its very nature costly, and is complex from the standpoint of operating technique. Probing techniques can be used, however, over wide ranges of temperature and pressure with a high degree of reproducibility. Apparatus for visual observation of phase behavior obviously has the advantage of enabling the experimenter to see exactly what takes place, but because the material to be tested is contained in a cell constructed of both metal and glass, is limited severely as to the temperature range of operation. Furthermore. the maximum pressure usually is limited by the choice of material used for sealing the glass to the metal, and by the strength of the glass itself. In the interest of increased efficiency of observation, as much of the cell as possible should be visible to the eye. Glass capillary tubes have been used successfully but have always given difficulty at the metal-to-glass seal. An apparatus has been devised to overcome the problems of sealing and resistance to temperature effects that have heretofore been the limiting factor with glass apparatus in the observation of phase volumes at elevated temperature and pressure. APPARATUS The objective which dictated the general arrangement of the apparatus (Figs. 1 and 2) was simplicity of operation. The air bath, A, was constructed of an iron framework to which was attached approximately one inch of glass wool bats which were covered on the outside with "Masonite." A roughly octagonal center piece was installed to provide forced circulation of the air by the fan, B, past the heaters, D, cell, F, and thermoregulator, C, respectively. The entire top of the box is removable to facilitate charging of the cell and to permit easy maintenance. Two windows are provided before and behind the cell to allow the operator to observe the contents against the background fluorescent light, E. The heaters,

Jan 1, 1951